SX-WD5
SPEAKER SYSTEM
ENCEINTE ACOUSTIQUE
SX-WD5
English
Français
INSTRUCTIONS
MANUEL D’INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT1236-004A
[J]
Warnings, Cautions and Others
English
7 Precautions for installation
• Do not install the speakers on an uneven surface or in a place subject to vibration;
otherwise, they may fall over, causing damage or injury.
– Take the occurrence of earthquakes or other physical shocks into consideration
when selecting the installation place, and secure the speakers thoroughly.
• To prevent deformation or discoloration of the cabinet, do not install the speakers
where they are exposed to direct sunlight or high humidity, and avoid installation near
air conditioning outlets.
• Speaker vibrations may cause howling. Place the speakers as far away from the player
as possible.
• The speakers are magnetically shielded to avoid color distortions on TVs. However, if
not installed properly, it may cause color distortions. So, pay attention to the following
when installing the speakers.
– When placing the speakers near a TV set, turn off the TV’s main power switch or
unplug it before installing the speakers.
Then wait at least 30 minutes before turning on the TV’s main power switch again.
Some TVs may still be affected even though you have followed the above.
If this happens, move the speakers further away from the TV.
• Tuner reception may become noisy or hissing if a speaker is installed near the tuner.
In this case, leave more distance between the tuner and the speakers or use an
outdoor antenna for better tuner reception without interference from the speakers.
7 Precautions for daily use
• To maintain the appearance of the speakers
– Wipe with a dry, soft cloth if the cabinet should become dirty.
If very dirty, wipe with a cloth applied a small amount of water or neutral detergent,
then wipe with a dry cloth.
– Do not use chemicals such as benzine and thinner for cleaning the cabinet;
otherwise, the speakers may deteriorate or its paint may come off.
• To improve the sound field
– It is recommended to leave a space of more than 50 cm between the speakers and
the wall.
– If the speakers are facing a solid wall or glass door, etc., it is recommended to
furnish the wall with materials that absorb sounds, for example by hanging up thick
curtains, to prevent reflections and standing waves.
• To use the speakers without any trouble
– Do not reproduce sounds at so high a volume that they are distorted; otherwise, the
speakers may be damaged by internal heat buildup.
– When moving the speakers, do not pull the speaker cords; otherwise, the speakers
may fall over, causing damage or injury.
2
Connection
7 Precautions
Before connecting:
• Make sure to match the polarity (ª and ·) when connecting the speaker cords.
• Turn off the power to the amplifier before connecting the speaker system; otherwise,
the speakers may be damaged.
• The impedance of the speaker is 6 Ω.
If this does not match with the speaker impedance range indicated on the amplifier,
you cannot connect this system to the amplifier.
• The maximum power handling capacity of the SX-WD5 is 100 W. Excessive input will
result in abnormal noise and possible damage.
Daily operations and maintenance:
• Be sure to turn down the volume level on the amplifier to prevent unwanted noise
before performing following operations:
– Turning on or off other components
– Operating the amplifier
– Tuning FM stations
– Fast-forwarding a tape
– Continuously reproducing high frequency oscillation or high pitch electronic sounds
– Connecting or disconnecting a microphone
• When using a microphone, do not aim it at the speakers or use it near the speakers;
otherwise, the howling which occurs may damage the speakers.
• Before replacing the cartridge, always turn off the power both to the amplifier and to
the turntable; otherwise, the clicking noise may damage the speakers.
7 Connecting the speaker system to the amplifier
• Twist and remove the insulation at the end of each speaker cord before
connecting.
English
· terminal
(Black hoop)
Silver
ª terminal
(Red hoop)
Copper
1 2 3
To the speaker ª
terminal of amplifier
To the speaker ·
terminal of amplifier
3
Loading...