SPEAKER SYSTEM
SX-LC33
English
INSTRUCTIONS
LVT1264-001A
[U, UP]
Thank you for purchasing a JVC speaker.
Before you begin using it, please read the instructions carefully
to be sure you get the best possible performance. If you have any
questions, consult your JVC dealer.
English
Warnings, Cautions and Others
7 Precautions for installation
• Do not install the speakers on an uneven surface or in a place
subject to vibration; otherwise, they may fall over, causing
damage or injury.
– Take the occurrence of earthquakes or other
physical shocks into consideration when
selecting the installation place, and secure the
speakers thoroughly.
• To prevent deformation or discoloration of the
cabinet, do not install the speakers where they are
exposed to direct sunlight or high humidity, and
avoid installation near air conditioning outlets.
• Speaker vibrations may cause howling. Place the
speakers as far away from the player as possible.
• The speakers are magnetically shielded to avoid
color distortions on TVs. However, if not installed
properly, it may cause color distortions. So, pay attention to the
following when installing the speakers.
– When placing the speakers near a TV set, turn off the TV’s
main power switch or unplug it before installing the
speakers.
Then wait at least 30 minutes before turning on the TV’s
main power switch again.
Some TVs may still be affected even though you have followed
the above. If this happens, move the speakers further away
from the TV.
• Tuner reception may become noisy or hissing if a speaker is
installed near the tuner. In this case, leave more distance
between the tuner and the speakers or use an outdoor
antenna for better tuner reception without interference from
the speakers.
7 Checking the supplied accessories
• Speaker cord (3m, 1)
• Feet (4)
If any item is missing, contact your dealer immediately.
7 Attaching the feet
Attach the supplied feet on the bottom of the speaker, so that you
can protect the speaker cabinet, decrease the vibration of the
speaker cabinet and prevent the speaker from slipping.
• Turn the speaker upside down and attach the feet as
illustrated.
Peel off
Bottom of the
speaker
7 Precautions for daily use
• To maintain the appearance of the speakers
Wipe with a dry, soft cloth if the cabinet should become dirty.
If very dirty, apply a small amount of water or neutral detergent
to the cloth and wipe clean, then wipe with a dry cloth.
• To improve the sound field
– It is recommended to leave a space of more than 50 cm
between the speakers and the wall.
– If the speakers are facing a solid wall or glass
door, etc., it is recommended to furnish the wall
with materials that absorb sounds, for example by
hanging up thick curtains, to prevent reflections
and standing waves.
• To use the speakers without any trouble
– Do not reproduce sounds at so high a volume that they are
distorted; otherwise, the speakers may be damaged by
internal heat buildup.
– When moving the speakers, do not pull the speaker cords;
otherwise, the speakers may fall over, causing damage or
injury.
Place a large, thick cloth under the speaker in order to
protect the floor and the speaker.
7 To remove the speaker grille
To remove the speaker grille, insert your fingers at the bottom
of the speaker grille, then pull upward.
To attach the speaker grille, put the projections of the speaker
into the holes of the speaker grille.
• Do not push the speaker grille strongly.
2
Connection
7 Connecting the speaker system to the amplifier
Before connection—
• Turn off the power to the amplifier before connecting the
speaker system; otherwise, the speakers may be damaged.
• The impedance of the speaker is 6 Ω. Before connecting it to
your amplifier, check the speaker impedance range of your
amplifier. If the impedance of this speaker is out of the speaker
impedance range indicated on the amplifier, you cannot
connect this system to the amplifier.
• The maximum power handling capacity of the SX-LC33 is
120 W. Excessive input will result in abnormal noise and
possible damage.
• Be sure to turn down the volume level to prevent unwanted
noise before performing following operations:
– Turning on or off other components,
– Operating the amplifier,
– Tuning FM stations,
– Fast-forwarding a tape,
– Continuously reproducing high frequency oscillation or high
pitch electronic sounds.
• When using a microphone, do not aim it at the speakers or
use it near the speakers; otherwise, the howling which occurs
may damage the speakers.
• Before replacing the cartridge, always turn off the power to the
turntable; otherwise, the clicking noise may damage the
speakers.
7 Connecting the speaker cord to the speaker
Connect the speaker cord to the speaker as follows.
1
Twist and remove the insulation at the end of each
speaker cord before connecting.
2
Rotate the speaker terminal knob counterclockwise and
fit the speaker cord into the groove. Then rotate the knob
clockwise to secure the cord.
Tighten
ª terminal
(Red)
· terminal
(Black)
Silver
Copper
To the speaker ª
terminal of amplifier
To the speaker ·
terminal of amplifier
Loosen
English
About speaker cords—to improve the sound quality
About the OFC cord
The core wires of the supplied speaker cords are made of OFC (Oxygen Free Copper). This OFC cord enables high quality
sound reproduction.
When connecting the speaker cords
Make sure to match the polarity (ª and ·); otherwise, the surround effect will become less effective.
After connecting, check that the exposed cores are fully inserted into the terminal.
When using other speaker cords
Observe the following;
• Buy thick speaker cords rather than thin cords, and make them as short as possible for connection.
• Do not use long speaker cords; otherwise, the sound quality may deteriorate.
• Use speaker cords of the same length for both left and right speakers.
• Using a special speaker cord such as a litz wire, a coaxial cable, or a cord which has the specified connecting directionality
may influence the sound quality.
Specifications
Type: 2-way 3-speaker bass-reflex type
Magnetically-shielded type
Speakers
Woofer: 13.5 cm cone x 2
Tweeter: 1.9 cm dome x 1
Power handling capacity: 120 W
Impedance: 6 Ω
Crossover frequency: 4 000 Hz
Frequency range: 52 Hz to 80 000 Hz
Sound pressure level: 89 dB/W•m
Dimensions (W x H x D): 150 mm x 415 mm x 292.5 mm
Mass: 8.0 kg
Design and specifications subject to change without notice.
3
感謝您惠購 JVC 揚聲器。
在開始使用之前，請您仔細閱讀本使用說明書，以確保您獲得揚聲
器的最佳性能。若有疑問，請與JVC代理銷售商聯繫。
警告，注意及其他
7 安裝時的注意事項
• 切勿將揚聲器放置在凹凸不平處或受到震動處。否則揚聲器摔
落可能導致自身損壞或損傷他物。
– 在選擇安裝場所時，須事先考慮到可能會發生地
震或其他物理性衝擊等情況，確保揚聲器安裝牢
靠。
• 為防止機殼變形或變色，勿將揚聲器安裝在受到陽光
直射或高度潮溼處，亦避免安裝在空調器的排氣孔附
近。
• 揚聲器的振動可能產生顫噪。應盡量將揚聲器遠離唱
機放置。
• 盡管揚聲器具有磁性屏蔽性能可以避免造成電視機色彩失真，但
如果安裝不當仍然可能引起電視機色彩失真。因此在安裝揚聲器
時請注意以下事項。
– 如果欲將揚聲器安裝在電視機附近，在安裝揚聲器之前請先關
閉電視機的主電源開關或拔下電源插頭。
在重新啟動電視機的主電源之前至少要等待 30 分鐘。
盡管您已經按照上述方法去做，有些電視機仍然會受到影響。發
生此種情況時，須將揚聲器移到遠離電視機處進行安裝。
• 如果將揚聲器安裝在調諧器附近，在調諧器接收時可能出現噪音
或嘶嘶聲。發生此種情況時，須將調諧器與揚聲器之間多空出一
些距離，或者使用室外天線，這樣調諧器便不會受到揚聲器的干
擾，而獲得較好的接收效果。
7 檢查附件
• 揚聲器導線 (3m, 1)
• 支腳 (4)
如果有任何項目遺漏，請速與經銷商聯絡。
7 安裝支腳
將隨機附帶的支腳安裝到揚聲器的底部，以便保護揚聲器外殼，減
小揚聲器機殼的震動，防止揚聲器滑倒。
• 將揚聲器倒置，如圖所示安裝支腳。
剝下封紙
揚聲器底部
7 日常使用時的注意事項
• 保養揚聲器的外表
如果機殼出現髒污，可用干爽柔軟的布進行擦拭。
如果髒污嚴重，可在布上沾少量的水或中性洗滌劑擦去污物，
然后再用干布擦拭。
• 改良音場
– 建議在揚聲器與牆壁之間留出 50 cm 以上的間隔。
– 如果揚聲器面對固質材料的牆壁或玻璃門等設施，
建議您使用吸音性材料，如厚料窗簾來裝飾牆壁，
這樣便可以防止發生反射波和駐波。
• 常規使用揚聲器
– 勿在極高，乃至出現聲音失真的音量下播放音響，否則揚聲
器內部熱量積聚可能損壞揚聲器。
–
在移動揚聲器時勿拉扯揚聲器導線；
自身損壞或損傷他物。
否則揚聲器摔落可能導致
在揚聲器的底下鋪一張大的厚布，以便保護地板和揚聲器。
7 如何卸下揚聲器罩網
要卸下揚聲器罩網時，將手指插入揚聲器罩網底部，然后朝前拉。
要裝上揚聲器罩網時，將揚聲器上的插銷插到揚聲器罩網上的插孔
里。
• 切勿過度用力推插揚聲器罩網。
4
連接
7 將揚聲器系統連接到功率放大器上
進行連接之前—
• 在連接揚聲器系統之前，首先關閉功率放大器的電源，否則可能
損壞揚聲器。
• 每隻揚聲器的阻抗為 6 Ω。在將揚聲器系統連接到功率放大器上
之前，首先檢查功率放大器能夠對應的揚聲器阻抗範圍。如果揚
聲器的阻抗超出了功率放大器上標出的揚聲器阻抗範圍，便不能
將該揚聲器系統連接到功率放大器上。
• SX-LC33 的最大額定功率為 120 W。超過該值以上的信號傳入
時將會產生異常噪音並可能受到損壞。
• 在執行下列操作之前確保調低音量水平，以防止出現異常噪音：
– 啟動或關閉其他組件，
– 操作功率放大器，
– 調收 FM 電台，
– 快速前進倒帶，
– 連續播放高頻振幅或高調電子音。
• 在使用麥克風時，不要將其朝向揚聲器，也不要在揚聲器附近
使用，否則顫噪可能會損壞揚聲器。
• 在更換唱頭之前，請務必關閉唱機的電源，否則喀噪音可能會
損壞揚聲器。
7 將揚聲器導線連接到揚聲器上
請按如下方法將揚聲器導線連接到揚聲器上。
1
在連接之前，擰下每根揚聲器導線末端的絕緣皮。
2
逆時針方向旋轉揚聲器端子上的旋鈕，將揚聲器導線放到線槽
內。然后順時針方向旋轉旋鈕以固定導線。
擰緊
ª 端子
（紅）
· 端子
（黑）
銀色
銅色
至功率放大器的揚聲器
ª 端子
至功率放大器的揚聲器
· 端子
鬆開
關于
揚聲器導線—如何提高音響質量
關于 OFC 導線
隨機提供的揚聲器導線的芯線是以 OFC（無氧銅）製成。此種 OFC 導線可為您播出高質量的音響。
在連接揚聲器導線時
確保對準極性（ª 和 ·）；否則，環繞聲效果將會丟失。接線之后，須檢查裸露的線芯是否全部插入到端子內。
在使用其他揚聲器導線時
請遵守下列事項；
• 購買揚聲器導線時盡量買粗的而不要買細的，而且接線盡量要短。
• 對左置和右置揚聲器使用相同長度的揚聲器導線。
• 不要使用過長的揚聲器導線，否則音響質量會降低。
• 使用特殊的揚聲器導線，如辮線，同軸電纜或帶有特定的連接定向性的導線可能會影響音響質量。
規格
類型： 2 向 3 揚聲器
低音反射型，磁性屏蔽型
揚聲器：
低音揚聲器： 13.5 cm 圓錐型 x 2
高音揚聲器： 1.9 cm 圓頂型 x 1
額定功率： 120 W
阻抗： 6 Ω
分解頻率： 4 000 Hz
頻率範圍： 52 Hz 至 80 000 Hz
聲壓水平： 89 dB/W•m
尺寸（寬 x 高 x 深）： 150 mm x 415 mm x 292.5 mm
重量： 8.0 kg
設計及規格如有變更恕不另行通知。
5
6
한국어
제공된 부속품의 확인
설치에 관한 유의사항
화면의 색상 왜곡을 방지하는 자기장
세트와 가까운 곳에 스피커를 설치할 경우에는, 스피커
TV
TV
TV
일상적인 사용시의 유의사항
이상 공간을 두는 것이
JVC
스피커를 구입해 주셔서 감사합니다.
JVC
대리점으로
한국어
타입:
웨이
스피커 저음 반향 타입
콘형
돔형
W
스피커 코드를 스피커에 연결하기
앰프에 스피커 시스템 연결하기
W
방송 튜닝
높이
안길이):
코드를 이용하면 고음질의 사운드를
단자
단자
단자에
단자에
SX-LC33
SPEAKER SYSTEM
EN, CS, KO
0704NSMMDWHCE© 2004 Victor Company of Japan, Limited
CAUTIONS / /
English
SX-LC33
7 For Unpacking
• Take out the speaker by holding the
bands.
• Do not touch the speaker grille or
speaker units; otherwise, it will be
damaged.
EN, CS, KO
7
Bands
Speaker units
LV43477-002A
[U, UP]
Loading...