JVC SR-DVM70EU User Manual

Download

DVD / HDD & Mini DV VIDEO RECORDER

SR-DVM70EU

VIDEO

DV HDD DVD

AUX

CANCEL

LIVE

ENTER

STOP/

JUMP

RECMODE

DISPLAY

REMAIN

VPS/PDC

AUDIO

SUBTITLE

CLEAR

LIVECHECK

TV/CBL/SAT

MEMO/MARK

EDITDUBBING

ONSCREEN

ANGLE

CABLE/SAT

STANDBY/ON

PROGRAMME

NAVIGATIONTOPMENU

RETURN

NEXTPREVIOUS

SLOWSLOW PLAY/SELECT

PAUSEREC

SETUP

PROGRESSIVE

DVD

OPERATE

SAT

SCAN

S-VIDEO

VIDEO(MONO)L -AUDIO -R

INF-1

INPUTSELECT

RECDVDRECHDDRECDV

EJECTEJECTDISPLAY

DV/HDD/DVD RECMODE INSTANTREPLAY AUDIODUB. INSERT

RECPAUSEPLAY

FFREWSTOP

DVIN/ OUT

INSTRUCTIONS

LPT1002-001B

2 EN

SAFETY FIRST

Safety Precautions

The rating plate and the safety caution are on the rear of the unit.

WARNING: DANGEROUS VOLTAGE INSIDE WARNING: TO PREVENT FIRE OR SHOCK HAZARD,

DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE UNIT CORRECTLY AS INSTRUCTED. WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO THE INSIDE OF THIS UNIT. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

CLASS 1 LASER PRODUCT

REPRODUCTION OF LABELS WARNING LABEL INSIDE OF THE UNIT

IMPORTANT:

8 Please read the various precautions on page 2 before

installing or operating the unit.

8 It should be noted that it may be unlawful to re-record pre-

recorded tapes, DVDs, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

CAUTION:

8 When you are not using the unit for a long period of time, it is

recommended that you disconnect the power cord from the mains outlet.

8 Dangerous voltage inside. Refer internal servicing to

qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.

DISCLAIMER OF LIABILITY

JVC shall not be liable for any loss relating to the unit’s failure to properly record, store or playback any content (video, audio or otherwise) for any reason whatsoever. Any applicable warranties shall only cover replacement or repair of the effected unit, and shall not apply to recovery or replacement of lost content.

ATTENTION:

8 Using a mobile phone in the vicinity of the unit may cause

picture vibration on the TV screen or change the screen to a blue back display.

8 Some TVs or other appliances generate strong magnetic

fields. Do not place such appliances on top of the unit as it may cause picture disturbance.

When moving the product, press A to turn off the power, and wait at least 30 seconds before unplugging the power cord. Then, wait at least 2 minutes before moving the product.

8 If there is a power outage when using the unit, the recorded

data may be erased.

8 It is recommended to back up discs which contain important

recordings periodically (every few years). As digital signals do not deteriorate, failure to play back or record might arise due to the effects of the disc aging through the years depending on the storage environment.

8 Recorded programs and data cannot be restored once the

disc is damaged.

● Manufactured under licence from Dolby Laboratories. ADolbyB and double-D symbol are trademarks of Dolby Laboratories.

● ADTSB and ADTS DIGITAL OUTB are trademarks of Digital Theater Systems, Inc.

● Cassettes marked P can be used with the DV deck of this unit. The DV deck can play back and record only PAL signals.

● SHOWVIEW is a trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under license from Gemstar

Development Corporation.

● This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual

property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing users only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

HOW TO USE THIS INSTRUCTION MANUAL

● All major sections and subsections are listed in the Table Of Contents on page 4. Use this when searching for information on a specific

procedure or feature.

● The Index on pages 10 – 13 illustrates the controls and connections on the front and rear panel, the front display panel and the remote

control.

● The list of terms on page 90 lists frequently-used terms, and the number of the page on which they are used or explained in the manual.

● The A mark signals a reference to another page for instructions or related information.

● Operation buttons necessary for the various procedures are clearly indicated through the use of illustrations at the beginning of each

major section.

For Italy:

AIt is declared that this product, brand JVC, conforms to the Ministry Decree n. 548 of 28 Aug.’95 published in the Official Gazette of the Italian Republic n. 301 of 28 Dec.’95B

The OPERATE A button does not completely shut off mains power from the unit, but switches operating current on and off. ABB shows electrical power standby and ACB shows ON.

When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear).

When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

Failure to heed the following precautions may result in damage to the unit, remote control or disc.

1. DO NOT

^ ^ in direct sunlight. ^ in a dusty environment. ^ ^ on a surface that is unstable or subject to vibration.

2. DO NOT

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

3. DO NOT

4. DO NOT or remote control.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

5. DO NOT

6. DO NOT water. Also DO NOT place any containers filled with water or

liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit.

7. DO NOT candles, on the apparatus.

8. AVOID

place the unit ^

in an environment prone to extreme temperatures or humidity.

in an environment where strong magnetic fields are generated.

block the unit’s ventilation openings or holes.

place heavy objects on the unit or remote control. place anything which might spill on top of the unit

expose the apparatus to dripping or splashing. use this equipment in a bathroom or places with

place any naked flame sources, such as lighted

violent shocks to the unit during transport.

SAFETY FIRST

MOISTURE CONDENSATION

Moisture in the air will condense on the unit when you move it from a cold place to a warm place, or under extremely humid conditions^just as water droplets form on the surface of a glass filled with cold liquid. In conditions where condensation may occur, disconnect the unit’s power plug from the wall and keep it disconnected for a few hours to let the moisture dry, then turn on the unit.

IMPORTANT:

Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment.

If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer.

In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your nearest JVC dealer.

If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below: DO NOT make any connection to the Larger Terminal coded E or Green. The wires in the mains lead are coloured in accordance with the following code:

Blue to N (Neutral) or Black Brown to L (Live) or Red

If these colours do not correspond with the terminal identifications of your plug, connect as follows: Blue wire to terminal coded N (Neutral) or coloured Black. Brown wire to terminal coded L (Live) or coloured Red.

If in doubt^consult a competent electrician.

EN 3

Some Do’s And Don’ts On The Safe Use Of Equipment

This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.

DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment)

are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or

changing connections. DO consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment. DO be careful with glass panels or doors on equipment.

DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way^switch off,

withdraw the mains plug and consult your dealer. DON’T remove any fixed cover as this may expose dangerous voltages. DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has

a standby mode. Switch off using the switch on the equipment and make sure that your family knows how to do this. Special

arrangements may need to be made for infirm or handicapped people. DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of road safety. It is illegal to

watch television whilst driving. DON’T listen to headphones at high volume, as such use can permanently damage your hearing. DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause damage and shorten

the life of the equipment. DON’T use makeshift stands and NEVER fix legs with wood screws^to ensure complete safety always fit the manufacturer’s approved

stand or legs with the fixings provided according to the instructions. DON’T allow electrical equipment to be exposed to rain or moisture.

ABOVE ALL...

^ NEVER let anyone especially children push anything into holes, slots or any other opening in the case^this could result in a fatal

electrical shock;

^ NEVER guess or take chances with electrical equipment of any kind^it is better to be safe than sorry!

4 EN

CONTENTS

SAFETY FIRST 2

Safety Precautions.........................................................................2

DISC INFORMATION 5

About Discs....................................................................................5

INDEX 10

INSTALLING YOUR NEW UNIT 16

Basic Connections .......................................................................16

INITIAL SETTINGS 17

Auto Set Up..................................................................................17

Preset Download..........................................................................18

Language .....................................................................................20

Monitor Set...................................................................................21

BASIC OPERATIONS ON DVD DECK 22

Basic Playback.............................................................................22

Playback Features .......................................................................23

Using The On-screen Bar ............................................................27

Parental Lock ...............................................................................31

Basic Recording...........................................................................32

Recording Features......................................................................33

BASIC OPERATIONS ON HDD DECK 35

Basic Recording...........................................................................35

Recording Features......................................................................36

Basic Playback.............................................................................37

Playback Features .......................................................................37

BASIC OPERATIONS ON DV DECK 39

Basic Playback.............................................................................39

Playback Features .......................................................................40

LIVE MEMORY PLAYBACK ON HDD/DVD DECK 41

Live Memory Playback.................................................................41

TIMER RECORDING ON HDD/DVD DECK 44

SHOWVIEW Timer Programming ...................................................44

Manual Timer Programming.........................................................46

Automatic Satellite Programme Recording

(HDD Deck Only).......................................................................48

NAVIGATION ON HDD/DVD DECK 49

Library Database Navigation .......................................................49

Edit Original Information .............................................................. 50

Edit Play List Information............................................................. 52

Edit Library Information ............................................................... 54

Playback With MP3/WMA/JPEG Navigation ...............................55

EDITING 56

Dubbing .......................................................................................56

DV Dubbing (HDD & DVD Deck Only) ........................................ 59

Edit From A Camcorder............................................................... 61

Edit To Or From Another Recorder ............................................. 62

Output/Input Set .......................................................................... 63

Digital Audio Dubbing .................................................................. 64

Audio Dubbing (DV Deck Only) ................................................... 65

Insert Editing (DV Deck Only)...................................................... 66

REMOTE CONTROL 67

Remote Control Functions........................................................... 67

SYSTEM CONNECTIONS 69

Connecting To A Satellite Receiver............................................. 69

Connecting To A Dolby Digital Decoder Or

An Amplifier With Built-in DTS .................................................. 70

Connecting/Using A Decoder ......................................................70

SUBSIDIARY SETTINGS 71

Mode Set .....................................................................................71

HOWVIEW System Setup ............................................................ 74

Tuner Set..................................................................................... 74

Clock Set .....................................................................................77

Format A Disc (DVD Deck Only) .................................................78

Finalise A Disc (DVD Deck Only) ................................................79

Scan Mode Set (HDD & DVD Deck Only) ...................................80

Tray Lock (DVD Deck Only) ........................................................ 80

Mode Lock ................................................................................... 80

Last Function Memory ................................................................. 80

TROUBLESHOOTING 81

SPECIFICATIONS 85

APPENDIX 86

LIST OF TERMS 90

About Discs

Recordable/Playable Discs

You can use discs with the following logos for recording and playback.

DVD-RAM

12 cm: 4.7 GB/9.4 GB 8 cm: 1.4 GB/2.8 GB Ver. 2.0/2x speed Ver. 2.1/1x – 3x speed Ver. 2.2/5x speed

DVD-R

12 cm: 4.7 GB 8 cm: 1.4 GB Ver. 2.0/1x – 4x/8x speed (Video mode)

● The above table is based on the information as of October 2004.

● Recording and playback may not be performed depending on the

characteristics and condition of the disc used, leading to unsatisfactory results. Using discs manufactured by JVC is recommended since they have been tested to be compatible with this unit.

DVD-RAM Discs

It is only possible to use discs which conform with DVD-RAM standard Version 2.0 or 2.1.

● It is impossible to record on DVD-RAM discs which do not

conform to this standard. If you use a disc formatted under a different standard version, format it on this unit before use.

● It may not be possible to record, play back, edit or dub a

DVD-RAM disc even if it conforms to the standard if it was recorded or edited on the devices from other manufacturers or on a PC, or if it has far too many titles, or if there is very little available capacity remaining on the disc.

● DVD-RAM discs recorded on this unit cannot be played back on

an incompatible DVD player.

● It is possible to record copy-once programmes of digital

broadcasts only onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs are not compatible).

DVD-RW

12 cm: 4.7 GB/9.4 GB Ver. 1.1/1x – 2x speed (Video mode/VR mode) Ver. 1.2/4x speed (Video mode/VR mode)

DISC INFORMATION

EN 5

DVD-R/RW Discs

It is only possible to use DVD-R discs which conform with DVD-R standard Version 2.0. When a DVD-R/RW disc (Video mode) is finalised (A pg. 79), it can be played back on a standard DVD player as a DVD VIDEO disc. When a DVD-RW disc (VR mode) is finalised (A pg. 79), it can be played back on a standard DVD player compatible with the VR mode of DVD-RW discs.

Before finalising ^ ^ it is possible to record on unrecorded areas of the disc, edit the

disc title and programme titles, and delete programmes.

● It is impossible to record or edit DVD-R/RW discs recorded on

other devices even if they have not been finalised.

● It is impossible to overwrite recorded areas of DVD-R discs.

● Available recording capacity does not increase even if a recorded

programme is deleted from a DVD-R disc.

After finalising ^

After a DVD-R/RW disc (Video mode) has been finalised, it is possible to play back the recorded programmes (video and/or audio) on a standard DVD video player as a DVD VIDEO disc.

● Edited titles are displayed as the

ADVD menuB in video mode.

● It is impossible to record, edit or

delete the data either in video mode or in VR mode.

● Either in video mode or in VR

mode, although the disc can be played back on DVD players from

HOME MOVIES DOCUMENTARIES

MTV CARTOON

TRAVELLINGCLIPS

other manufacturers, sometimes it may not be possible to play back depending on the disc and recording conditions.

● It is impossible to record on CD-R/RW or DVD-R discs used for

authoring.

● It is impossible to record onto DVD-R/RW (Video mode) discs

broadcasts that allow you to copy once. The copy once programmes can only be recorded onto DVD-RW discs formatted in VR mode.

NOTE:

The following may result if you play back a DVD-R disc recorded on another unit.

● The disc does not play.

● A mosaic pattern (block noise) appears on the screen.

● Video or audio may be dropped out.

● The unit stops during playback.

6 EN

DISC INFORMATION

Discs For Playback Only

You can use discs with the following logos for playback only.

DVD VIDEO Video CD/Super Video CD

(example of region code indications)

Audio CD

CD-DA files

CD-RW

CD-DA/JPEG/ MP3 files

● Playback may not be performed depending on the characteristics

and condition of the disc used.

● DTS Audio CDs can also be played back (An optional DTS

decoder is required).

● MP3 and JPEG discs can be played back on this unit only when

they have been recorded in the ISO9660 or Joliet format and finalised.

● JPEG files that can be played back on this unit must conform to

JFIF/Baseline process, and the maximum resolution of a JPEG file is 2,812 pixels in width and 2,112 pixels in height.

● CD-R/RW discs recorded in music CD format need to be finalised

to play back on this unit.

● Operation and audio quality of this unit are not guaranteed for

discs that do not conform to the Compact Disc specification (CD-DA). Before you play back a CD, check for the CD logo and read the notes on the package to confirm that it conforms to the Compact Disc specification.

● Depending on the intentions of the author of the software,

recording conditions of DVD discs and Video CD/SVCD discs may be restricted. Since this unit plays back discs according to the intentions of the author of the software as indicated on the disc, some functions may not operate as commanded.

● When switching from the first layer to the second layer of double-

layered DVD VIDEO discs, the image and sound may be momentarily distorted. This is not a malfunction.

● DVD-AUDIO discs compatible with DVD video players can be

played.

● Super Audio CDs (SACD) compatible with conventional CD

players can be played.

CD-R

CD-DA/JPEG/ MP3 files

CD-ROM

JPEG/MP3 files

Unplayable Discs

The following types of discs cannot be played using this unit. Do not attempt to play back any kind of disc that is damaged (cracked, warped, or repaired with adhesive tape) or discs in unusual shapes (heart-shaped, octagonal, or other forms). If such discs are accidentally played back, it may cause noise that can lead to speaker damage.

● CD-ROM discs (including PHOTO-CD and CD-G)

● Discs recorded in Packet Write (UDF) format

● 1.3-GB double density CDs (DDCD)

● High density CDs (HDCD)

The following discs also cannot be played back.

● Discs of a region number other than A2B

● DVD-RAM (2.6 GB/5.2 GB)

● DVD-RAM (TYPE1)

Caution for DualDisc playback

The Non-DVD side of a ADualDiscB does not comply with the ACompact Disc Digital AudioB standard. Therefore, the use of Non-

DVD side of a DualDisc on this product may not be recommended.

Region Number

The world is divided into 6 regions for DVD VIDEO discs. DVDVIDEO discs are assigned a region number to indicate which region they may be played back in. A disc cannot be played back on this unit unless the region number of the disc matches that of the unit. The region number for this unit is A2B. Only discs whose region number includes A2B or AALLB can be played back such as shown below.

Examples of DVD VIDEO labels which can be played back using this unit.

Marks of discs in this instruction manual

Allows operation with a DVD-RAM disc.

Allows operation with a DVD-R disc.

Allows operation with a DVD-RW disc .

Allows operation with a DVDVIDEO disc.

Allows operation with a Video CD/Super Video CD (SVCD) disc.

Allows operation with an Audio CD disc.

Allows operation with a disc including MP3 files.

Allows operation with a disc including JPEG files.

Recording Medium And Format

DVD-RAM

● Recording and erasing can be performed as many times as

possible on a disc.

● Editing can be performed after recording, such as deleting

unwanted parts.

● While recording, it is possible not only to start playback of a

programme currently being recorded, but also to watch another programme previously recorded.

DVD-RW (VR mode)

● Recording and erasing can be performed as many times as

possible on a disc.

● Editing can be performed after recording, such as deleting

unwanted parts.

DVD-RW (Video mode)

● Can be played back on other DVD players.

● New recording can be performed by erasing all the data on a disc

once played back.

DVD-R

● Can be played back on other DVD players.

● Suitable when keeping a recorded disc for a long time.

File Structure Of Discs

DVD VIDE O

Typically, DVD VIDEO discs are made up of larger units called AtitlesB. Each title has a number (title number) that can be used to select desired titles. Titles are further divided into units called AchaptersB. Each chapter has a number (chapter number) that can also be used to select desired chapters. Note that some discs are not divided into titles and chapters.

When you record a programme on a DVD-RAM/RW (VR mode) disc

A single recording session results in a single title (a single chapter). However, chapter marks are automatically inserted when recording is paused, or audio changes from monaural to stereo due to commercial breaks, etc. It is also possible to insert chapter marks at desired locations during playback. (A pg. 25)

When you record a programme on a DVD-R/RW (Video mode) disc

A single recording session results in a single title (a single chapter). However, chapter marks are automatically inserted when recording is paused, or audio changes due to commercial breaks, etc. It is also possible to insert chapter marks at desired locations during either recording or playback. Once the disc has been finalised, these chapter marks are deleted and new chapter marks are assigned automatically approximately every 5 minutes.

DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc

Title 1 Title 2

Chapter 1 Chapter 2

● In Video mode, even before finalising, it is impossible to perform

Chapter 3

editing operations other than changing the disc name and/or title names and deleting programmes and/or titles.

● After finalising, it is impossible to perform editing operations.

Chapter 1

Chapter 2

Chapter 3

DISC INFORMATION

EN 7

Audio CD/Video CD/SVCD

Typically, Audio CD discs are divided into separate tracks each containing one song. Each track is assigned a number. For example, the third track is Track 3. The same is true for Video CD/ SVCD discs. However, some discs are not divided into tracks.

Audio CD or Video CD/SVCD

Track 1 Track 2 Track 3 Track 4

JPEG/MP3 Disc (CD-R/RW/ROM)

MP3/JPEG files put in directories nested in several levels on a disc will be organized as if they were put in single level directories (groups) by the MP3/JPEG Navigation of this unit. (A pg. 55)

File structure of a disc before starting the MP3/JPEG Navigation

Directory MP3 file JPEG file

File structure of the disc after starting the MP3/JPEG Navigation

Files are automatically grouped as follows and displayed on the MP3/JPEG Navigation screen. Data is displayed in the alphabetical order of file name. Files are grouped based on roots.

● This unit can recognise up to 9 hierarchies including directories

and files. Also, it can recognise up to 250 files in each group, and up to 99 groups on a disc.

NOTES:

● Video CD/SVCD discs that support Playback Control (PBC)

The contents of a disc are recorded into several hierarchies, and played back according to the instructions on the screen while navigating through the hierarchies. It is also possible to playback recorded tracks consecutively without activating the PBC function even when playing a PBC-compatible disc. (A pg. 26)

● Regarding the contents recorded on discs

Some files may not be played back depending on the file types and other factors.

8 EN

EJECT DV/HDD/DVD REC MODE INSTANTREPLAY AUDIO DUB. INSERT

RECDVD

DVIN/ OUT

RECPAUSEPLAY FFREWSTOP

DISC INFORMATION

DVD VIDEO Marks

Sometimes marks are printed on a DVD disc and/or on its packaging to indicate information regarding the contents and functions of the disc. Check the marks indicating the contents and functions of the disc. Note, however, that in some cases a disc may not include a mark even for a function it supports.

Marks related to video

Number of subtitles Number of angles

Recorded under the standard 4:3 aspect ratio

Video playback is in Wide video mode (16:9) on wide televisions, but in letter box on televisions with standard 4:3 aspect ratio.

Video playback is in Wide video mode (16:9) on wide televisions, but pan and scan is used on televisions with standard 4:3 aspect ratio (either the left or right side of the image is cut-out).

Marks related to audio

Number of audio tracks

Screen includes black bands at the top and the bottom of image which has a standard 4:3 aspect ratio (letter box)

Placing A Disc

Opening the disc tray

Press M to open the disc tray.

● Pressing the button again closes the disc tray.

● Use the button to open and close the disc tray.

● Do not block the disc tray with your hand while it is opening or

closing as this may result in hardware failure.

● Do not place unplayable discs or any object other than a disc on

the disc tray.

● Do not press down strongly on the disc tray or place any heavy

objects on it.

Discs without cartridges

Dolby Digital mark It has been developed by Dolby Laboratories as a digital surround system.

DTS (Digital Theater Systems) You can enjoy DTS audio if you connect an amplifier with a built-in DTS decoder to the DIGITAL OUT connector of the unit.

Disc tray

Place the disc on the disc tray with the label side facing up. Since disc size changes depending on the disc to be played back, be sure to correctly align the disc with the grooves for its size. If the disc is not in its groove, it may be scratched or otherwise damaged. To insert an 8 cm disc, place it according to the inner groove.

DVD-RAM discs contained in cartridges

Double-sided discs:

Remove the disc from the cartridge. Align the disc with the grooves on the disc tray as shown in the illustration and insert with the side you wish to play back or record facing down. If you insert the disc with ASide AB facing down, programmes are recorded on the side A.

Single-sided discs:

Remove the disc from the cartridge. Align the disc with the grooves on the disc tray as shown in the illustration and insert with the label side facing up.

Care And Handling Of Discs

How to handle discs

When handling a disc, do not touch the surface of the disc. Since discs are made of plastic, they are easily damaged. If a disc gets dirty, dusty, scratched or warped, the images and sound will not be picked up correctly, and such a disc may cause the unit to malfunction.

Label side

Do not damage the label side, stick paper to or use any adhesives on its surface.

Recording side

Make sure that discs are not scratched or dirty on the recording side before use. Scratches and dirt on the recording side of a disc may hinder proper playback and recording. Also be careful that a DVD-RAM disc may get scratched or dirty when removed from cartridge then put back in after use.

Storage

Make sure that discs are kept in their cases. If discs are piled on top of one another without their protective cases, they can be damaged. Do not put discs in a location where they may be exposed to direct sunlight, or in a place where the humidity or temperature is high. Avoid leaving discs in your car!

DISC INFORMATION

EN 9

Maintenance of discs

If there are fingerprints or other dirt adhering to a disc, wipe with a soft dry cloth, moving from the centre outwards. If a disc is difficult to clean, wipe with a cloth moistened with water. Never use record cleaners, petrol, alcohol or any anti-static agents.

CAUTION:

Sometimes during playback, noise may appear or images may be garbled. This is sometimes due to the disc. (It may not be up to industry standards.) These symptoms are caused by the discs, not by the malfunction of the unit.

10 EN

INDEX

Front View

OPERATE

S-VIDEO

IN F-1

VIDEO (MONO)L- AUDIO - R

INPUT SELECT

FFREWSTOP

LMBA

RECPAUSEPLAY

DVIN/ OUT

HGI

EJECTEJECTDISPLAY

RECDVDRECHDDRECDV

DV/HDD/DVD REC MODE INSTANT REPLAY AUDIODUB. INSERT

A OPERATE Button (A) B Eject Button (EJECT M) (DV) A pg. 39 C Mini DV Cassette Loading Slot D DV Lamp (DV) A pg. 39

DV Recording Lamp (REC)

E HDD Lamp (HDD) A pg. 20, 35

HDD Recording Lamp (REC) A pg. 35

F DVD Lamp (DVD) A pg. 20, 22

DVD Recording Lamp (REC) A pg. 32

G Open/Close Button (EJECT M) (DVD) A pg. 8 H DV/HDD/DVD Select Button (DV/HDD/DVD) A pg. 22, 35, 39

● This button will not function during navigation mode or set up

mode.

I Recording Mode Button (REC MODE) A pg. 32, 35 J Instant Replay Button (INSTANT REPLAY) A pg. 26, 38, 40 K Disc Tray L Audio Dubbing Button (AUDIO DUB.) A pg. 65 M Insert Button (INSERT) A pg. 66

N Display Button (DISPLAY) A pg. 25, 33 O S-video Input Connector [S-VIDEO] A pg. 61 P Video/Audio Input Connectors

[VIDEO/AUDIO ((MONO) L/R)] A pg. 61

Q Input Select Buttons (INPUT SELECT JK) A pg. 32, 35 R Front Display Panel A pg. 12 S Infrared Beam Receiving Window T Stop Button (STOP o) A pg. 22, 37 U Reverse Search Button (O) (HDD & DVD deck) A pg. 23,

42 Rewind Button (REW O) (DV deck) A pg. 39, 40

V Play Button (PLAY I) A pg. 22, 37 W Forward Search Button (N) (HDD & DVD deck) A pg. 23,

42 Fast Forward Button (FF N) (DV deck) A pg. 39, 40

X Pause Button (PAUSE W) A pg. 22, 37 Y Record Button (REC R) A pg. 32, 35 Z DV Input/Output Connector [DV IN/OUT(A*)] A pg. 59

* A (i.Link) refers to the IEEE1394-1995 industry specification and

extensions thereof. The i.Link standard.

A logo is used for products compliant with the

Rear View

INDEX

EN 11

ACDB

DIGITAL

AUDIO OUT

PCM/STREAM

COAXIAL

OPTICAL

HDD/DVD

A Region Number A pg. 6 B AC Power Cord A pg. 16 C Cooling Fan

● This prevents the temperature from rising inside the unit.

Do not remove it.

● Install the unit so as not to block the area around the fan.

● The unit may become hot when it is turned off, as the cooling

fan on the rear of the unit is not activated. However, the cooling fan may be activated in the following cases;

^ In the Automatic Satellite Programme Recording standby

mode (A pg. 48), slightly before the starting time of VPS/PDC recording (A pg. 45).

^ If you connect the decoder or satellite receiver to [L-2 IN/

DECODER], and if AL-2 SELECTB is set to ADECODERB, ASAT VIDEOB or ASAT S-VIDEOB. (A pg. 63)

^ When AJUST CLOCKB is set to AONB (A pg. 77).

(Set AJUST CLOCKB to AOFFB if you mind the noise of the fan.)

COMPONENT

VIDEO OUT

HDD/DVD

ANTENNA

OUT

REMOTE IN

S-VIDEO OUT

L-1

F G H

AUDIO OUT

RIGHT

VIDEO OUT

LEFT

IN/OUT

L-2

IN/DECODER

K L

D Digital Audio Output Connectors

[DIGITAL AUDIO OUT (OPTICAL/COAXIAL)] (HDD & DVD deck only) A pg. 64, 70

E S-video Output Connector [S-VIDEO OUT] A pg. 16 F Audio Output Connectors [AUDIO OUT (LEFT/RIGHT)]

A pg. 16

G BNC Video Output Connector [VIDEO OUT] A pg. 16 H Component Video Output Connectors [COMPONENT

VIDEO OUT (Y/P

B/PR

)] (HDD & DVD deck only) A pg. 16

I Antenna Input Connector [ANTENNA IN] A pg. 16 J Remote Input Connector* [REMOTE IN]

* There is currently no compatible remote control unit available.

K L-1 Input/Output Connector [L-1 IN/OUT] A pg. 16, 62, 69,

L L-2 Input/Decoder Connector [L-2 IN/DECODER] A pg. 62,

69, 70

M Antenna Output Connector [ANTENNA OUT] A pg. 16

12 EN

INDEX

Front Display Panel

ACBD GF

VPS/PDC

EIHJ

LPCM FR XP SP LP EP

RW VCD

RAM

A VIDEO Indicator (z) A pg. 33, 36

Lights when VIDEO mode is selected by pressing TV AV/ VIDEO. Lights off when TV mode is selected.

B Disc Type Indicator

When a disc is loaded, the type of the disc is indicated.

Disc Status Indicator

When a disc is running, the disc marks rotate. During High-Speed Search:

Rotate faster than normal playback.

During Slow Motion:

Rotate slower than normal playback.

While recording:

Inner red ring lights in the same way as normal playback. During Instant Timer Recording (ITR), inner red ring slowly blinks.

While paused:

Disc marks blink when either recording or playing back. While stopped: Disc marks all light. While resume stopped: Disc marks all blink. While the disc tray opened: Disc marks all light out. No disc on the disc tray: Disc marks all light out.

VR Mode Indicator (VR) A pg. 78

Lights when a DVD-RW disc is formatted in VR mode.

C VPS/PDC Indicator A pg. 45

Appears when checking if the station being received transmits a VPS/PDC signal.

D Linear PCM Indicator (LPCM)

Lights when AXP MODE REC AUDIOB is set to ALINEAR PCMB (A pg. 72) for recording with HDD, DVD-RAM, DVD-R and DVD-RW discs, and when Linear PCM audio is played.

E Cassette Loaded Mark (u)

Indicates the present of a cassette in the DV deck. Lights when a cassette is loaded into the DV deck. It will remain lit as long as the cassette is loaded, even if the HDD or DVD deck is being selected.

F Recording Mode Indicator (XP/SP/LP/EP/FR) A pg. 32

Blinks when recording mode is being set. While AFRB is blinking, the left 3 digits of the Multi Display (P R) indicate setting values ranging from A60B to A480B. After the value has been set, only AFRB lights.

G Group/Title Indicator (GRP/TITLE)

AGRPB or ATITLEB lights depending on a disc loaded while the left 2 digits of the Multi Display (P) indicate the numbers explained below.

AGRPB: Total number of groups or group number being played

ATITLEB: Total number of titles or title number being played

H Channel Indicator

Indicates the channel received.

back are displayed on the Multi Display.

I Track/Chapter Indicator (TRK/CHAP)

ATRKB or ACHAPB lights depending on a disc loaded while the 3rd and 4th digits from the left of the Multi Display (R) indicate the numbers explained below.

ATRKB: Total number of tracks or track number being played

ACHAPB: Chapter number being played back are displayed on

J Simulated Surround Effect Indicator (3D) A pg. 29

Lights when a simulated surround effect is set to A3D-ONB on the on-screen bar.

K Random/Programme Playback Mode Indicator (RND/

PRGM) A pg. 30

ARNDB: Lights when Random Playback mode is set. APRGMB: Lights when Programme Playback mode is set.

L Repeat Mode Indicator (x/1/A-B) A pg. 27

Select Repeat Playback mode on the on-screen bar.

AxB: Whole disc is played back repeatedly. Ax1B: A single title/chapter/track is played back

AxA-BB: The selected part (A-B) is played back repeatedly.

No display: Repeat Playback mode is off.

M VPS/PDC Recording Indicator A pg. 45

Lights when VPS/PDC recording function is activated.

N Video Output Indicator (q) A pg. 80

No display: Indicates that interlace mode is engaged. q: Indicates that progressive mode is engaged. (Example) q lights when video output mode is in progressive mode.

O Automatic Satellite Programme Recording Indicator

A pg. 48

Lights when the HDD deck is in the Auto Satellite Programme Recording standby mode.

P Group/Title Number Display Q Audio Dubbing/Insert Editing Indicator

AADUBB or AINSB lights up during Audio Dubbing or Insert Editing respectively.

R Track/Chapter Number Display S Remaining Time/Elapsed Time Indicator A pg. 25, 33

Lights when remaining time of HDD, DVD-RAM, DVD-R and DVD-RW discs is displayed, and lights out when elapsed time is displayed. The right 6 digits of the Multi Display (T) indicate elapsed or remaining time of each track. No display: Indicates elapsed time of the disc. Displayed: Indicates remaining time of the disc.

T Remaining Time/Elapsed Time Display A pg. 25, 33

Time Code Display A pg. 40

U Multi Display

Displays clock, received channel, elapsed time, and remaining time. Also displays status of the unit (NO DISC/OPEN/CLOSE/ READING).

back are displayed on the Multi Display.

the Multi Display.

repeatedly.

Remote Control

CABLE/SAT

DVD

A B

C D

DV H DD DVD

VIDEO

STANDBY/ON

DVD

TV/CBL/SAT

AUX

CANCEL

LIVE

MEMO/MARK

PROGRAMME

EDITDUBBING

H I J K

NAVIGATIONTOP MENU

ENTER

RETURN

NEXTPREVIOUS

SLOWSLOW PLAY/SELECT

CLEAR

STOP/

JUMP

PAUSEREC

REC MODE

DISPLAY

ON SCREEN

ANGLE

LIVE CHECK

SET UP

SAT

PROGRESSIVE

SCAN

Q R

REMAIN

AUDIO

VPS/PDC

SUBTITLE

A TV AV/VIDEO Button A pg. 33, 36 B TV Muting Button (TV d) A pg. 67 C DV Button* A pg. 39

* This button will not function during navigation mode or set up mode.

D HDD Button* A pg. 35

* This button will not function during navigation mode or set up mode.

E Number Keys A pg. 32, 35 F Cancel Button (CANCEL(L)) A pg. 30 G Auxiliary Button (AUX): Not use on this unit. H Live Button (LIVE) A pg. 42 I Dubbing Button (DUBBING) A pg. 56 J Top Menu Button (TOP MENU) A pg. 23 K FGDE Buttons A pg. 17 L Menu Button (MENU) A pg. 23 M Reverse Skip Button (S) A pg. 23, 42, 38

Previous Button (PREVIOUS) A pg. 26

N Reverse Search Button (O) (HDD & DVD deck) A pg. 23,

42 Rewind Button (O) (DV deck) A pg. 39 Reverse Slow Button (SLOW –) A pg. 24

O Record Button (R) A pg. 32, 35 P Jump Button (JUMP +/–) A pg. 38 Q Recording Mode Button (REC MODE) A pg. 32, 35

Remain Button (REMAIN) A pg. 25, 33

R Display Button (DISPLAY) A pg. 25, 33, 40

V W

X Y

b c

d e

f g

i j

k l m n

o p

INDEX

EN 13

S VPS/PDC Recording Button (VPS/PDC j) A pg. 45 T Audio Button (AUDIO) A pg. 26 U Subtitle Button (SUBTITLE) A pg. 26 V TV/CABLE/SAT/DVD switch A pg. 20 W DVD STANDBY/ON Button (DVD A) X TV/CBL/SAT STANDBY/ON Button (TV/CBL/SAT A)

A pg. 67

Y DVD Button* A pg. 22

* This button will not function during navigation mode or set up mode.

Z TV Volume Buttons (TV8 +/–) A pg. 67 a Programme Buttons (PR +/–) A pg. 32, 67 b Memo Button (MEMO) A pg. 50, 53

Mark Button (MARK) A pg. 25

c Programming Button (PROGRAMME) A pg. 44, 46, 47 d Edit Button (EDIT) A pg. 50 e Navigation Button (NAVIGATION) A pg. 49 f Enter Button (ENTER) A pg. 20 g Return Button (RETURN) A pg. 26, 28, 44 h Forward Skip Button (T) A pg. 23, 42

Next Button (NEXT) A pg. 26

i Forward Search Button (N) (HDD & DVD deck) A pg. 23,

42 Fast Forward Button (N) (DV deck) A pg. 39 Forward Slow Button (SLOW +) A pg. 24

j Play Button (I) A pg. 22, 37

Select Button (SELECT) A pg. 55

k Pause Button (W) A pg. 22, 37 l Stop Button (o) A pg. 22, 37

Clear Button (CLEAR

) A pg. 30

m Skip Search Button (v) A pg. 24, 42 n Set Up Button (SET UP) A pg. 20 o Instant Replay Button (w) A pg. 42 p On-Screen Button (ON SCREEN) A pg. 14, 27 q Automatic Satellite Programme Recording Button (SAT j)

A pg. 48

r Progressive Scan Button (PROGRESSIVE SCAN) A pg. 80 s Angle Button (ANGLE) (DVD deck only) A pg. 25

Live Check Button (LIVE CHECK) A pg. 42

How To Use

Before use, insert two R6 size batteries into the remote control with the polarity (F and G) matched correctly as indicated on the battery compartment or on the lid.

The remote control can operate most of your unit’s functions, as well as basic functions of TV sets and satellite receivers and other brands. (A pg. 67)

● Point the remote control toward the receiving window.

● The maximum operating distance of the remote control is

about 8 m.

NOTE:

If the remote control doesn’t work properly, remove its batteries, wait a short time, replace the batteries and then try again.

14 EN

7: 00 XP 10: 00 SP 20: 00 LP 28: 00

36: 00

FR480

ITR 2 : 30

INDEX

On-Screen Display (HDD & DVD deck)

When ASUPERIMPOSEB is set to AONB or AAUTOB and ON SCREEN on the remote control is pressed, various operational indicators appear on the TV screen. To clear the operational indicators, press ON SCREEN twice.

When playing back a recorded title HDD

0:00 1:00 2:00

FISHING WORLD

01:16:48

FR360

Digital

When pressing REC MODE

(Appears for eight seconds.)

A Remaining disc time for each recording speed B Recording speed

When pressing R during recording

A Title start B Current playback point C Title end D Elapsed playing time E Play mode F Name of title currently being played back G Time scale (This title is an hour and a half long.) H Audio mode

DVD

TITLE99 CHAPTER999 REMAIN6:59:59 T.

FISHING WORLD

Digital

A Playback title number B Playback chapter number C Disc remaining time D Current status (playback) E Audio mode F Bar meter G Name of title (or play list) currently being played back H Current playback point I Recorded mode

When recording HDD

11:00 12:00 13:00

FR360

11:35

PR.12

LIVE

A Recording time for Instant Timer Recording (ITR) mode

When using Live Memory playback HDD

11:00 12:00 13:00

FR360

11:35

11:33

PR.12

DVD

TITLE99 CHAPTER999 REMAIN6:59:59 T.

RAM

FR360

11:35

11:33

PR.12

A Time scale for recording (HDD deck)

Bar meter for recording (DVD deck)

B Current recording point C Recording mode D Current time E Current playback channel position number F Time scale for Live Memory Playback (HDD deck)

Bar meter for Live Memory Playback (DVD deck)

G Current playback point H Live Memory playback mode I Current playback time

DVD

TITLE99 CHAPTER999 T. REMAIN6:59:59

RAM

FR360

A Recording point B Current status (recording) C Current time D Recording channel number

11:35

PR.12

LIVE

INDEX

SE CL EANI NG CASSET TE

61BIT

R000:00:00:

G F

A B

EN 15

On-Screen Display (DV Dubbing)

When capturing images from the external DV equipment

0:00 1:00 2:00

HDD

00: 00:00. 00

FR360

12bit

JVC

GR-DV3500DV

A Recording speed B HDD capacity graph C HDD time counter D Recording time scale E HDD mode F Remote control mode G Connected DV equipment mode H Connected DV equipment model information I Input channel J Sound mode K Sound input bit-rate*

* Indicates the sound bit-rate of the connected DV equipment

L Connected DV equipment information*

* Maker name and model name, etc. may not appear depending on the

connected equipment.

M Time counter for the connected DV equipment N Sound monitor mode

DV DV

O Remote control switch P Auto capture button Q Sound monitor switch

GR-DV3500

00: 00:00. 00

SOUND1

1 2

On-Screen Display (DV deck)

A Operation Mode Indicators B Tape Speed (SP/LP) C Sound Mode Display A pg. 72 D Current Day/Month/Year/Clock Display/Time Code Display

A pg. 40

E Audio Mode Display A pg. 40 F Warning Message G Auxiliary Input Indicator (L-1, L-2, F-1 or DV) H ACassette LoadedB Mark

R Elapsed recording time

179 : 59 : 59

16 EN

INSTALLING YOUR NEW UNIT

Basic Connections

TV aerial cable

Mains outlet

Mains power cord

Back of unit

To [S-VIDEO To [AUDIO OUT]

Audio cable (not supplied)

S-video cable

(not supplied)

To [L-1 IN/OUT]

OUT]

It’s essential that your unit be properly connected.

ATTENTION:

Connect the AC plug only after all connections to the TV has been completed.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

1 Make sure the package contains all of the accessories listed in

ASPECIFICATIONSB (A pg. 85).

2 Place the unit on a stable, horizontal surface. 3 Connect the unit to a TV depending on the TV and cables you

use.

8 Basic Connection To connect to a TV with 21-pin SCART connector ^

A Disconnect the TV aerial cable from the TV. B Connect the TV aerial cable to the [ANTENNA IN] connector on

the rear panel of the unit.

C Connect the [ANTENNA OUT] connector on the rear panel of

the unit and the TV’s aerial connector with the supplied RF cable.

D Connect the [L-1 IN/OUT] connector on the rear panel of the

unit and the TV’s 21-pin SCART connector with a supplied 21pin SCART cable.

● The [L-1 IN/OUT] connector accepts and delivers either a

composite signal (regular video signal), Y/C signal or RGB signal.

● Set your TV to the VIDEO (or AV), Y/C, or RGB mode

according to the type of your TV’s SCART connector.

To [ANTENNA IN]

21-pin SCART cable (supplied)

BNC video

cable (not

supplied)

To [VIDEO OUT]

To 75 ohm terminal

To [COMPONENT VIDEO OUT (Y/P

B/PR

)]

[ANTENNA

OUT]

Component video cable (not supplied)

RF cable

(supplied)

To connect to a TV with BNC connector ^

A Perform A – C of ATo connect to a TV with 21-pin SCART

connector ^B in the left column.

B Connect an optional audio cable between the [AUDIO OUT]

connectors on the rear panel of the unit and the TV's audio input connectors.

C Connect an optional BNC video cable between the unit's BNC

[VIDEO OUT] connector and the TV's BNC VIDEO input connector.

8 S-Video Connection To connect to TV’s S-VIDEO input and AUDIO input connectors ^

A Perform A – C of ATo connect to a TV with 21-pin SCART

connector ^B in the left column.

B Connect the unit’s [S-VIDEO OUT] connector to the TV’s

S-VIDEO input connector.

C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO

input connectors.

● If your TV is not stereo-capable, use the unit’s [AUDIO OUT]

connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

● Set AL-1 OUTPUTB to ASCART S-VIDEOB when using the S-

Video connection.

8 Component Video Connection To connect to TV’s component video input connectors ^

A Perform A – C of ATo connect to a TV with 21-pin SCART

connector ^B in the left column.

B Connect the unit’s [COMPONENT VIDEO OUT (Y/P

B/PR

)]

connectors to the TV’s component video input connectors.

C Connect the unit’s [AUDIO OUT] connectors to the TV’s AUDIO

input connectors.

● You can obtain high-quality component video pictures.

● The [COMPONENT VIDEO OUT (Y/P

B/PR

)] connectors do not

output DV signals.

● If your TV is not stereo-capable, use the unit’s [AUDIO OUT]

connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

● By using the component video connection, you can view the

images in the progressive mode. For switching to the progressive mode, refer to AScan Mode Set (HDD & DVD Deck Only)B (A pg. 80).

NOTE:

Select an appropriate option of AL-1 OUTPUTB as follows (A pg. 63):

When your TV’s SCART connector accepts:

Set AL-1 OUTPUTB to:

Composite signals ASCART VIDEOB Y/C signal (separated

luminance (brightness) and

ASCART S-VIDEOB

chrominance (colour) signals) RGB signal ASCART RGBB Component video signal ACOMPONENTB

When the setting selected is not in accordance with the TV connected and depending on the type of appliance connected to the unit, the correct picture will not appear.

4 Plug the end of the mains power cord into a mains outlet.

● ALOADINGB blinks on the front display panel when the AC plug

of the mains power cord is connected into a mains outlet and it takes approximately 50 seconds for the unit to be turned on. This is not a malfunction.

Auto Set Up

Auto Channel Set/Auto Clock Set/Auto Guide Programme Number Set

After the A button on the unit (or DVD A on the remote control) is pressed for the first time to turn on the unit selecting your country*, the Auto Set Up function sets the tuner channels, clock** and Guide Programme numbers automatically.

* If you live in Belgium (BELGIUM) or Switzerland (SUISSE), you also

need to select your language.

* If you live in Hungary (MAGYARORSZÁG), Czech Republic (ČESKÁ

REPUBLIKA), Poland (POLSKA) or other countries in Eastern Europe (OTHER EASTERN), set the clock manually.

CABLE/SAT

DVD A

, by simply

DVDTV

3 Press FGD E to select the

language of your choice, then press ENTER. The AUTO SET/ T-V LINK display appears on the TV screen.

4 Press DE to select AAUTO

SETB, then press ENTER. The

INITIAL SETTINGS

INITIAL SET UP > LANGUAGE SELECT

ENGLISH

DEUTSCH

ITALIANO

ESPAÑOL NORSK

SVENSKA DANSK

SELECT WITH @ THEN PRESS [ENTER]

ENTER

SET UP

EXIT

SELECT

INITIAL SET UP > AUTO CH SET

PRESS [SET UP] TO EXIT

FRANCAIS NEDERLANDS SUOMI

RETURN

EN 17

AUTO SET screen will appear.

● When AUTO SET is completed,

AUTO SET T-V LINK

ASCAN COMPLETEDB appears on the TV screen. Select AOKB.

SELECT WITH @ THEN PRESS [ENTER]

ENTER

ATTENTION:

SET UP

EXIT

SET UP

SELECT

INITIAL SET UP > AUTO SET

ENTER

EXIT

SELECT

PRESS [SET UP] TO EXIT

AUTO SET

PLEASE WAIT...

CANCEL

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

AAUTOB blinks on the front display panel; do NOT press any button on the unit or remote control until the front display panel shows A––:––B as illustrated on page 19.

● When you have connected the unit to a TV offering T-V Link via a

fully-wired 21-pin SCART cable (A pg. 16) and the TV is turned on, the unit automatically performs the Preset Download (A pg. 18) even if you select AAUTO SETB for Auto Set Up function.

ENTER

FGDE

Before starting, make sure of the following:

● The TV aerial cable should be connected to the unit.

● The unit’s mains power cord should be connected to a mains

outlet.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

1 Press A on the unit or DVD A on the remote control to turn

on the unit. The Country Set display appears on the TV screen.

2 Press FGD E to select your

country’s name, then press ENTER.

NOTES:

● If you have selected ABELGIUMB

or ASUISSEB, go to step 3.

● If you have selected

AMAGYARORSZÁGB, AČESKÁ REPUBLIKAB, APOLSKAB or

AOTHER EASTERNB, press ENTER. The Clock Set screen appears. Set the clock manually (A pg. 77), then go to step 4.

● If you have selected any other country name, go to step 4.

INITIAL SET UP > AREA SELECT

BELGIUM

ČESKÁ REPUBLIKA

DEUTSCHLAND ESPAÑA GREECE ITALIA MAGYA RORSZÁG NEDERLAND NORGE ÖSTERREICH POLSKA PORTUGAL SUISSE SUOMI SVERIGE OTHER WESTERN OTHER EASTERN

ENTER

SET UP

EXIT

SELECT WITH @ THEN PRESS [ENTER]

PRESS [SET UP] TO EXIT

SELECT

DANMARK

RETURN

ATTENTION:

Once you have performed Auto Set Up, even if the unit’s memory backup has expired, all the stored stations and their Guide Programme numbers remain in the unit’s memory and the unit will not perform Auto Set Up again. The unit only performs Auto Clock Set when the unit is turned on. If you have moved to a different area, perform each setting as required.

● Tuner setting (A pg. 74)

● Clock setting (A pg. 77)

If a new station starts broadcasting in your area, perform tuner setting. (A pg. 74)

NOTES:

● In areas where no TV station transmits a PDC (Programme

Delivery Control) signal, the unit can perform neither Auto Clock Set nor Auto Guide Programme Number Set.

● If there is a power cut, or if you press A or SET UP while Auto

Set Up is in progress, Auto Set Up will be interrupted; be sure to turn off the unit power once and try again from step 1.

● Auto Clock Set may not function properly depending on the

reception condition.

● If no sound accompanies the picture or the audio sounds

unnatural on some channels that have been stored by Auto Set Up, the TV system setting for those channels may be incorrect. Select the appropriate TV system for those channels. (A pg. 76, AINFORMATIONB)

After AAuto Set UpB is completed, perform AMonitor SetB on page 21.

18 EN

INITIAL SETTINGS

Preset Download

Auto Channel Set by Downloading from TV/Auto Clock Set/Auto Guide Programme Number Set

ATTENTION:

You can use this function only with a TV offering T-V Link, etc.* Be sure to use a fully-wired 21-pin SCART cable.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic,

SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

CABLE/SAT

DVDTV

ENTER

If you have connected the unit to your TV via a 21-pin SCART cable (A pg. 16), the unit will automatically perform Preset Download instead of the Auto Set Up in step 4 on page 17. After downloading, the unit sets the clock and Guide Programme numbers automatically.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Perform steps 1 to 3 of AAuto Set UpB (A pg. 17) before

continuing.

1 Press DE to select AT-V L I NKB and press ENTER. The T-V

LINK screen will appear.

● When T-V LINK is completed,

ASCAN COMPLETEDB appears on the TV screen. Select AOKB.

ATTENTION:

Preset positions on the front display panel increase from APR 1B; do NOT press any button on the unit or remote control until the front display panel shows clock time, APR 1B or A––:––B as illustrated on page 19.

● If you press any button on the unit or remote control while

downloading is in progress, it will be interrupted.

NOTES:

● For details, refer to the instruction manual of your TV.

● In the area where no TV station transmits a PDC (Programme

Delivery Control) signal, the unit can perform neither Auto Clock Set nor Auto Guide Programme Number Set.

● If there is a power cut, or if you press A or SET UP while

downloading or set up is in progress, it will be interrupted; be sure to turn off the unit power once and try again from the beginning.

● Auto Clock Set may not function properly depending on the

reception condition.

● On this unit, the characters available for station names (ID) are

A–Z, 0–9, –, Z, + and & (space). Some names of downloaded stations may differ from those of your TV. (A pg. 76)

INITIAL SET UP > AUTO CH SET

ENTER

SET UP

EXIT

SELECT

INITIAL SET UP > T-V LINK

ENTER

SET UP

EXIT

SELECT

AUTO SET T-V LINK

SELECT WITH @ THEN PRESS [ENTER]

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

PRESS [SET UP] TO EXIT

T-V LINK

PLEASEWAIT...

CANCEL

SELECT WITH @ THEN PRESS [ENTER]

PRESS [SET UP] TO EXIT

After APreset DownloadB is completed, perform AMonitor SetB on page 21.

Results Of Auto Set Up/Preset Download Appearing On The Front Display Panel

If both Auto Channel Set and Auto Clock Set have been performed successfully, the correct current time is displayed.

Turn on the TV and select its AV mode, then make sure that all necessary stations have been stored in the unit’s memory by using the PR +/– button(s).

● If station names (ID – A pg. 89) have also been stored in the

unit’s memory, the station name will be displayed at the top right corner of the TV screen for about 5 seconds when the unit is tuned to a different station.

● If you want to set the tuner manually such as to add or skip

channels, to change channel positions, or to set or change station names, see pages 75 – 76.

If Auto Channel Set has succeeded but Auto Clock Set has not, APR 1B (channel position) is displayed.

If both Auto Channel Set and Auto Clock Set have failed, A––:––B is displayed.

A Turn on the TV and select its AV mode, then make sure that all

necessary stations have been stored in the unit’s memory by using the PR +/– button(s).

● If station names (ID – A pg. 89) have also been stored in the

unit’s memory, the station name will be displayed at the top right corner of the TV screen for about 5 seconds when the unit is tuned to a different station.

● If you want to set the tuner manually such as to add or skip

channels, to change channel positions, or to set or change station names, see pages 75 – 76.

B Perfor m AClock SetB (A pg. 77).

ATTENTION:

After making sure the cables are connected properly, turn off the unit’s power once, then turn the unit’s power back on again. The Country Set display appears on the TV screen; perform AAuto Set UpB (A pg. 17) or APreset DownloadB (A pg. 18) again.

IMPORTANT:

● To check if the Guide Programme numbers have been set

correctly, perform the S (A pg. 44)

● In certain reception conditions, station names may not be stored

correctly, and auto Guide Programme Number Set may not work properly. If the Guide Programme numbers are not set properly when you timer-record a TV programme using the S system, the unit will record a TV programme of a different station. When programming the timer using the S sure to check the desired channel is selected correctly. (A pg. 44)

● Your unit memorizes all detected stations even if reception of

some of them is poor. You can delete those stations with an unacceptable picture. (A pg. 76, ADelete A ChannelB)

HOWVIEW Timer Programming.

HOWVIEW

HOWVIEW system, be

INITIAL SETTINGS

EN 19

INFORMATION

Language for the on-screen display

Auto Set Up also selects the language automatically for the onscreen display depending on the Country setting you have made in step 2 on page 17 (unless you have selected ABELGIUMB or ASUISSEB), as shown below.

SUOMI B SUOMI ITALIA B ITALIANO

PORTUGAL

DEUTSCHLAND POLSKA NORGE SVERIGE DANMARK ÖSTERREICH

ČESKÁ REPUBLIKA

B ENGLISH MAGYARORSZÁG B ENGLISH B DEUTSCH ESPAÑA B ESPAÑOL B ENGLISH NEDERLAND B NEDERLANDS B NORSK GREECE B ENGLISH B SVENSKA OTHER WESTERN B ENGLISH B DANSK B DEUTSCH OTHER EASTERN B ENGLISH B ENGLISH

If you want to change the language setting manually, see AOn- screen Language SetB (A pg. 20).

Just Clock

Your unit is equipped with the Just Clock function which provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. If you want to take advantage of this function, simply set it to AONB. (A pg. 77)

T-V Link Functions

When you connect the unit to your TV via a fully-wired 21-pin SCART cable (A pg. 16), the following functions are available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual of your TV.

* Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK,

Q-Link or DATA LOGIC via a fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.

TV Auto Power On

The TV will turn on and be set to its AV mode automatically whenever you start playback. For details, refer to the instruction manual of your TV.

Unit Auto Standby

You can use your TV’s remote control to turn off the unit. For details, refer to the instruction manual of your TV.

Direct Rec

You can easily start recording the programme that you are watching on your TV. When you use this function, set ADIRECT RECB to AONB. (A pg. 72)

20 EN

INITIAL SETTINGS

Language

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

HDD

ENTER

DVD

FGDE

SET UP

On-screen Language Set

This unit offers you the choice to view on-screen messages in 10 different languages.

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press DE to select A FUNCTION SET UPB, then press G.

DVDTV

4 Press DE to select A DISPLAY

SETB, then press G.

5 Press FG to select AON

SCREEN LANGUAGEB, then press ENTER.

6 Press FG to select your desired

language, then press ENTER.

7 Press SET UP to complete the

setting.

DVD VIDEO SET UP

REC/PLAY SET UP

SUPERIMPOSE

BLUE BACK

DIMMER

POWER SAVE

ON SCREEN LANGUAGE

SET UP

EXIT

HDD/DVD/DV SET UP

FUNCTION SET UP

DISPLAY SET

ENTER

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

SELECT

VIDEO IN/OUT

AUTO

BRIGHT

ENGLISH

INITIAL SET UP

OFF

Menu/Audio/Subtitle Language Set (DVD deck only)

Some DVD discs contain the DVD menu display, audio and subtitles in multiple languages. With these discs, you can set the default language as you like.

● The procedure shows how to set AMENU LANGUAGEB as an

example.

1 Press DVD so that the DVD lamp lights up on the unit. 2 Press SET UP to access the Main Menu screen. 3 Press DE to select A DVD VIDEO SET UPB, then press G. 4 Press DE to select

ALANGUAGE SETB, then press

5 Press FG to select AMENU

LANGUAGEB, then press ENTER.

6 Press FG to select your desired

language, then press ENTER.

● See ALanguage Code ListB (A pg. 86).

7 Press SET UP to complete the setting.

NOTE:

When the selected language is not available on the disc, the disc’s default menu language is played back.

DVD VIDEO SET UP

HDD/DVD/DV SET UP

LANGUAGE SET AUDIO OUTPUT

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ENTER

SET UP

EXIT

SELECT

INITIAL SET UP

FUNCTION SET UP

PARENTAL LOCK DISC PLAY SET UP

ENGLISH

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

Monitor Set

You can select the monitor type depending on the TV used when you play back DVD VIDEO discs recorded for wide-screen TVs.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

DVDTV

DVD

ENTER

FGDE

SET UP

INITIAL SETTINGS

1 Press DVD so that the DVD lamp lights up on the unit. 2 Press SET UP to access the Main Menu screen.

● You cannot set the monitor type during recording or playback.

3 Press DE to select A FUNCTION SET UPB, then press G. 4 Press DE to select AVIDEO IN/

OUTB, then press G.

5 Press FG to select AMONITOR

TYPEB, then press ENTER.

6 Press FG to select the desired

option, then press ENTER.

7 Press SET UP to complete the

setting.

*The boldface settings below indicate the settings at your purchase.

8 MONITOR TYPE - 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX

4:3LB (Letter Box conversion):

Select this when the aspect ratio of your TV is 4:3 (conventional TV). While viewing a wide screen picture, the black bars appear on the top and the bottom of the screen.

4:3PS (Pan&Scan):

Select this when the aspect ratio of your TV is 4:3 (conventional TV). While viewing a wide screen picture, the black bars do not appear; however, the left and right edges of the pictures will not be shown on the screen.

16:9AUTO (Wide television conversion):

Select this when the aspect ratio of your TV is 16:9 (wide TV).

16:9FIX (Wide television conversion):

Select this when the aspect ratio of your TV is fixed to 16:9 (wide TV). The unit automatically adjusts the screen width of the output signal correctly when playing back a picture whose aspect ratio is 4:3.

DVD VIDEO SET UP

REC/PLAY SET UP

MONITOR TYPE

F-1 INPUT

L-1 OUTPUT

L-1 INPUT

L-2 SELECT

SET UP

EXIT

HDD/DVD/DV SET UP

FUNCTION SET UP

DISPLAY SET

SELECT WITH @ THEN PRESS [ENTER]

ENTER

PRESS [SET UP] TO EXIT

SELECT

VIDEO IN/OUT

4:3LB

VIDEO

SCART VIDEO

VIDEO

EN 21

INITIAL SET UP

Pan&Scan/Letter Box

In general, DVDVIDEO disc are produced for a wide-screen TV with 16:9 aspect ratio. Material with this ratio will not fit to a TV with 4:3 aspect ratio. There are two styles to display the image, APan&ScanB (PS) and ALetter BoxB (LB).

Pan&Scan

The right and left side of the image are cut off. The image fills the screen.

● The picture will be shown in the A4:3LBB mode

depending on the disc even if the A4:3PSB mode is selected.

Letter Box

Black bands appear at the top and bottom of the image. The image itself appears in 16:9 aspect ratio.

22 EN

BASIC OPERATIONS ON DVD DECK

Basic Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

DV/HDD/DVD

DVD

ENTER

CABLE/SAT

To play back an MP3/JPEG disc, see APlayback With MP3/WMA/ JPEG NavigationB (A pg. 55).

1 Load a disc.

● For details, refer to APlacing A DiscB (A pg. 8).

● Pressing I also closes the disc tray.

● Playback begins automatically if an auto-playback DVD disc is

loaded.

2 Press DV/HDD/DVD on the unit repeatedly or DVD on the

remote so that the DVD lamp lights up on the unit.

3 Press I to start playback.

● If you load a DVD disc whose region code does not match the

unit, AREGION CODE ERRORB appears on the TV screen. For details, refer to ARegion NumberB (A pg. 6).

● If ACAN NOT PLAY BACK DISC UNDER CURRENT SETTINGB

appears on the TV screen, refer to AParental LockB (A pg. 31).

● With Video CD/SVCD discs with PBC control or some DVD

discs, the menu display may appear on the TV screen after

starting playback. In this case, select an item which you want to play back from the menu. Otherwise, the playback cannot go forward. Refer to APlayback Control (PBC) FunctionB (A pg. 26)

DVDTV

or ALocating A Desired Scene Using The DVD MenuB (A pg. 23).

● The Library Database Navigation also enables you to search

and select the desired titles. (A pg. 50)

4 Press W to pause playback.

● To resume normal playback, press I.

5 Press o to stop playback.

● When a recordable disc is played, playback stops and a

programme received with the unit’s tuner resumes on the TV screen.

● When a playback-only disc is played, playback stops and the

TV screen becomes all blue when you press o. Pressing o again resumes a programme received with the unit’s tuner.

● If M is pressed during playback, playback stops, then the disc

tray opens.

NOTES:

● When the Library Database Navigation screen appears, choose

a thumbnail image of the desired title on the TV screen, then press ENTER. (A pg. 50)

● It is not possible to playback the DVD disc recorded in 96 kHz on

DVD during recording or Live Memory Playback on HDD.

ATTENTION:

● It takes approximately 30 seconds to read a disc depending on

the type and condition of the disc since this unit is multi-disc compatible (DVD-RAM, DVD-RW, DVD-R). It may even take several minutes when a disc is dirty, scratched or warped.

● It may take a few seconds to start playback. This is not a

malfunction.

● Forward/reverse high-speed search and other operations

cannot be performed while playback is stopped.

BASIC OPERATIONS ON DVD DECK

EN 23

Playback Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press DVD so that the DVD lamp lights up on the unit.

CABLE/SAT

DVDTV

DVD

0-9

TOP MENU

ENTER

O/SLOW

JUMP

JUMP +

FGDE

T N/SLOW +

Locating The Start Point Of The Item Or Skip The Item

Press S or T during playback.

● Pressing T locates the start point or marked points of the item

or skips the item in the forward direction, then resumes playback.

● Pressing S locates the start point or marked points of the item

or skips the item in the reverse direction, then resumes playback.

Current playback point

programme

Scene 2

(Chapter 2)

Track 2

Reverse

: marked points (A pg. 25)

●

Drama

Scene 3

(Chapter 3)

Track 3

programme

Scene 4

(Chapter 4)

Track 4

(Chapter 5)

Forward

Movie

Scene 5

Tra ck 5

Variable Speed Search

Locating A Desired Scene Using The DVD Menu

DVDVIDEO discs may have top menu and disc menu.

Top m enu

DVD discs generally have their own menus which show the disc contents. These menus contain various items such as titles of a movie, names of songs, or artist information. You can locate a desired scene by using the top menu displayed on the TV screen. Press TOP MENU to access the top menu.

Disc menu

Disc menus include playback data (angle menu, subtitle menu, etc.) specific to each title. Press MENU to access the disc menu.

1 Press TOP MENU or MENU to

access the DVD menu.

2 Press FGD E to select a

desired title, then press ENTER. Playback starts.

● It may be possible to select the

desired item using the number keys depending on the menu

display.

NOTE:

When A7B appears on the TV screen in step 1, the disc does not have a top menu or disc menu.

Example:

During playback, press N for forward variable speed search, or O for reverse variable speed search.

● Each press of the button increases the search speed for each

direction.

● To resume normal playback, press I.

For Audio CD

You can perform 4 levels of speed search with N and O. (Audio is active also during variable speed search.) You cannot perform slow motion for each direction.

Reverse

Reverse Search

4 steps

-60 -15 -3 -113515

Reverse

-5

Play

Reverse

Slow Motion

3 steps

---

Slow Motion

16116

3 steps

Normal

Play

Forward

Forward Search

4 steps

Still Picture/Frame-By-Frame Playback

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) to activate frame-by-

frame playback.

● Each press of SLOW – (O) or SLOW + (N) advances/

reverses the still picture frame by frame.

● Frame-by-frame playback for reverse direction cannot be

performed with Video CD/SVCD discs.

● To resume normal playback, press I.

24 EN

BASIC OPERATIONS ON DVD DECK

Slow Motion

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) for 2 or more seconds.

● Each press of SLOW – (O) or SLOW + (N) increases the

slow motion speed for each direction.

● Slow motion for reverse direction cannot be performed with

Video CD/SVCD discs.

Skip Search

During playback, press v.

● Each press initiates an approximately 30-second period of fast-

motion playback. Normal playback resumes automatically.

● Skip search cannot be performed when a VCD/SVCD disc is

being played back with the PBC function.

Jump Search

You can locate a scene ahead or behind the current one by jumping scenes according to selected time intervals (A pg. 73) during playback (or Live Memory Playback). Press JUMP – or JUMP +.

● To advance forward or back, press JUMP – or JUMP +

repeatedly within 5 seconds of each press to continue jump.

● Depending on the time from where you want to start jump search,

the first press of JUMP – or JUMP + will not necessarily lead to a jump of the selected time interval. The first press will lead to a jump to the nearest quarter points of an hour (15 min/ 30 min/ 45 min/ 00 min). The subsequent jumps will then be in accordance to the selected time interval.

● When you cannot advance any further (beginning or end of

programme reached), the message AUNABLE TO GO BACK ANY MOREB appears on the screen and the on-air screen resumes. In such a case, press S, O or o.

Example:

Playback search when jump interval is set to 15 MIN jumps. Taking for instance, you want to start jump search 40 minutes after the beginning of the programme. Pressing result in a jump to the scene at the 30 minutes point or 45 minutes point respectively as illustrated below. At the subsequent press, the scene will jump to the 15 minutes point or 1 hour point respectively, according to the selected time interval, which in this case is

Time counter

0 min

Beginning of programme

15 min

30 min

Current scene

40 min

NOTE:

Jump search cannot be performed with finalised DVD-R/DVD-RW (video mode) discs.

45 min

JUMP –

1 h

End of programme

JUMP +

15 MINB.

1 h 15 min

will

Resume Function

It is possible to memorise the position where you stop playback and resume playback from that position.

● Be sure to set ARESUMEB to AONB or ADISC RESUMEB.

(A pg. 72)

● Resume function always works for DVD-R/DVD-RW discs that

have not been finalised and DVD-RAM regardless of the setting of ARESUMEB.

1 Press o during playback to memorise a resume point.

● The unit enters Resume Stop mode and memorises the

position where you have stopped playback as a resume point. (The inside of the disc status indicator on the front display panel blinks while memorising.)

● The unit retains a memory of the resume points of the last 30

discs played back, even though they have been ejected if ARESUMEB is set to ADISC RESUMEB. (A pg. 72)

● To clear the resume points:

(The inside of the disc status indicator stops blinking and lights.)

When ARESUMEB is set to AONB:

• Press A to turn off the unit.

• Press M to take out the disc.

• Press o in stop mode.

• Press

TOP MENU to display the top menu, then start playback

by selecting an item, etc.

• Press MENU to display the disc menu, then start playback by

selecting an item, etc.

When ARESUMEB is set to ADISC RESUMEB:

•Set ARESUMEB to AOFFB. (A pg. 72)

• Press

o in stop mode.

• Press

TOP MENU to display the top menu, then start playback

by selecting an item, etc.

• Press MENU to display the disc menu, then start playback by

selecting an item, etc.

2 Press I in stop mode to resume playback. The unit starts

playback from the resume point.

NOTES:

● ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and

already finalised DVD-R/DVD-RW (video mode) discs. For other types of discs, the function under AONB setting will be applied even if ARESUMEB is set to ADISC RESUMEB. (A pg. 72)

● If you stop the playback of a disc for which a resume point has

already been memorised, the memory will be updated with the new resume point.

● After the unit has memorised the resume points for 30 discs,

remembering a new resume point will cause the unit to delete the oldest memorised point. Stopping playback of a disc for which a resume point is already stored may change the order in which the points are stored. This may potentially change the order in which points are deleted.

● When the unit memorises a resume point for a disc, it also

remembers audio language, subtitle and angle settings.

● This function may not work for some Video CD/SVCDs.

● When ARESUMEB is changed to AONB or AOFFB (A pg. 72),

resume points of the discs memorised with ARESUMEB set to ADISC RESUMEB will be cleared.

● Resume points are memorised for each side of a double-sided

disc.

● When you switch to HDD while playing back JPEG/MP3 files,

playback stops. The Resume Function doesn’t work when you switch to DVD thereafter to playback the disc.

BASIC OPERATIONS ON DVD DECK

EN 25

CABLE/SAT

DVDTV

DVD

0-9

MARK

ENTER

S/PREVIOUS

I o

REC MODE/REMAIN

DISPLAY

AUDIO

FGDE

RETURNMENU T/NEXT

SET UP

ANGLESUBTITLE

Marking Positions To Play Back Again Later

It is possible to mark positions (up to 999 points) where you want to play back once again later, and start playback from a marked position. Marking onto DVD-RAM/RW (VR mode only) discs when recording is helpful to locate a start point when you play back the discs later.

To mark positions:

During playback, press MARK at positions you want to mark.

● AMARKB appears on the TV screen.

You can easily locate the marked positions using S or T when you play back the disc.

To delete the marked positions:

While paused, press S or T to locate a marked position you want to delete, then press MARK.

● Crossed AMARKB appears on the

TV screen, and the marked position is deleted.

NOTES:

● When a monaural programme changes to a stereo programme

while recording, a mark signal is automatically recorded.

● For DVD-R/RW (Video mode) discs, marks are assigned

automatically every 5 minutes.

● If MARK is pressed when playing back a disc that does not allow

marks to be inserted, A7B appears on the TV screen.

Checking The Time Information

You can check time information of a disc on the front display panel and the TV screen.

8 DVD-RAM/DVD-R/DVD-RW

Each press of DISPLAY on the remote control or the unit changes the display as follows:

During recording

Clock time (front display panel only) N Current title elapsed time N Disc remaining time* N (back to the beginning)

* only discs before finalising

During playback

Each title elapsed time N Current title elapsed time N Disc remaining time* N (back to the beginning)

* only discs before finalising

During recording/playback or in stop mode Press REC MODE.

● The disc remaining time according to recording modes appears

on the TV screen.

● It is possible to check disc remaining time according to recording

modes also by pressing REMAIN.

● In FR mode, it is possible to set recording time in detail. While the

recording mode and the disc remaining time are displayed by pressing REMAIN, press FG to select AFRB, then press DE to select the desired recording time. (A pg. 34)

● It is not possible to switch the recording mode during playback or

while recording.

8 Video CD/SVCD/Audio CD During playback or in stop mode

Current track elapsed time N Current track remaining time N Tot al elapsed time N Total remaining time N (back to the beginning)

NOTE:

When a PBC-compatible Video CD/SVCD disc is loaded, deactivate the PBC function. (A pg. 26)

Angle Selection

You can enjoy a variety of scene angles if a DVD VIDEO disc contains Amulti-angleB parts, where the same scene was shot from different angles. If the disc contains Amulti-angleB parts, AyB appears on the TV

screen at the beginning of the Amulti-angleB part.

1 Press ANGLE during

playback. The angle selection display appears on the TV screen.

2 Press ANGLE or DE to select

your desired angle.

● Each time you press ANGLE or DE, the angle changes.

● When A7B appears on the TV screen, the current scene is not

recorded from multiple angles. In addition, some discs prohibit angle selection.

● To clear the angle selection display, press ENTER. In addition,

the angle selection display disappears automatically if no operation is done for 10 seconds.

When 3 scene angles are contained.

26 EN

BASIC OPERATIONS ON DVD DECK

Subtitle Selection

Some DVD VIDEO discs contain more than one subtitle language, from among which you can choose the desired subtitle language. AhB appears on the TV screen at the beginning of the part where more than one subtitle language are recorded.

1 Press SUBTITLE during

playback. The subtitle selection display appears on the TV screen.

● Each time you press

SUBTITLE, the subtitle display is switched on and off.

When 3 subtitle languages are contained.

ENGLISH

2 Press DE to select your desired language.

● To clear the subtitle selection display, press ENTER.

NOTES:

● When A7B appears on the TV screen, no subtitle language is

recorded.

● When the subtitle language won’t be changed with the procedure

above, change the subtitle on a disc menu displayed by pressing MENU.

Audio Channel Selection

When watching bilingual programmes or playing discs on which you recorded bilingual or stereo programmes, you can choose the desired audio channel.

● When ASUPERIMPOSEB is set to AONB or AAUTOB, you can

confirm on the TV screen the audio channel you have chosen. (A pg. 73)

● Each time you press AUDIO, the audio

channel changes.

TRACK

On-Screen Display

For main audio of bilingual programme

For sub audio of bilingual programme

For stereo discs

For audio of left channel

For audio of right channel

NOTE:

It is not possible for DVD-R/DVD-RW (Video mode) disc playback to switch the audio channel. The audio channel is played back as set in AVIDEO MODE RECORDING AUDIOB setting. (A pg. 72)

When you can’t switch the audio channel of a bilingual programme

When the unit is connected with a digital audio device using an optional optical cable and ADIGITAL AUDIO OUTB is set to ADOLBY DIGITAL/PCMB, it is not possible to switch the audio channel of a bilingual programme recorded on a DVD-RAM or DVD-RW (VR mode) disc. (A pg. 70) In this case, perform the following steps using the remote control to switch ADIGITAL AUDIO OUTB from ADOLBY DIGITAL/PCMB to APCM ONLYB.

A Press SET UP to access the Main Menu screen. B Press DE to select ADVD VIDEO SET UPB, then press G. C Press DE to select AAUDIO OUTPUTB, then press G. D Press FG to select ADIGITAL AUDIO OUTB, then press

ENTER.

E Press FG to select APCM ONLYB, then press ENTER.

(A pg. 71)

F Press SET UP to complete the setting. G Press AUDIO to select the desired audio channel.

USE

Audio Language/Sound Selection

Some DVD VIDEO discs contain the multiple audio language or sound. You can select the desired audio language or sound. For some Video CD/SVCD discs, you can switch the audio channel to choose Karaoke either with or without the vocal.

1 Press AUDIO during playback.

The Audio Language/Sound selection display appears.

2 Press AUD IO or DE to select

your desired audio language/ sound.

● Each time you press AUDIO or DE, the audio language/sound

changes.

● To clear the Audio Language/Sound selection display, press

ENTER.

NOTES:

● When A7B appears on the TV screen, no audio language is

recorded.

● When the audio language won’t be changed with the procedure

above, change the audio on a disc menu displayed by pressing MENU.

● Pressing AUDIO to select the audio language/sound is only

possible during playback. It is not possible to select by pressing AUDIO in stop mode. However, you can select the desired audio language/sound from the setup menu while in stop mode.

For example: DVD VIDEO

When 3 audio languages are contained.

Playback Control (PBC) Function

Some Video CD/SVCD discs support the PBC function. PBC is an abbreviation of APlay Back ControlB. A Video CD/SVCD disc recorded with PBC has its own menus, such as a list of the songs on the disc. You can locate a specific scene by using the menu.

1 Press I in stop mode. The PBC menu appears. 2 Press the number keys to enter the number of the desired

scene, then press ENTER. The unit starts playback of the selected item.

● APBCB appears on the front display panel.

● When ANEXTB or APREVIOUSB appears on the TV screen:

Pressing NEXT(T) advances to the next page. Pressing PREVIOUS(S) returns to the previous page.

● You can return to the menu by pressing RETURN.

● The method of the operation is different depending on the disc.

NOTE:

If you want to playback a PBC-compatible Video CD/SVCD disc without activating the PBC function, start playback with the PBC function, then press o to stop playback. The TV screen becomes all blue. Then start playback in stop mode by using the number keys to choose the track, then press ENTER.

Instant Replay

You can move back the playback position slightly. Press w on the remote control or INSTANT REPLAY on the unit.

● Each press skips back for approximately 7 seconds and resumes

playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

Using The On-screen Bar

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

The on-screen bar allows you to control various playback functions. Some of the functions operated on Navigation Menu can be controlled on the On-screen bar.

ATTENTION:

The on-screen bar can also be used for the HDD deck.

Be sure to clear Library Database Navigation screen by pressing NAVIGATION.

CABLE/SAT

DVDTV

BASIC OPERATIONS ON DVD DECK

EN 27

A Disc type. B Select this for Repeat Playback. (A pg. 27) C Select this for A-B Repeat Playback. (A pg. 28) D Select this for search function. (A pg. 28) E Select this for time search function. (A pg. 29) F Select this to switch Simulated Surround Effect function.

(A pg. 29)

G Select this for Picture Control function. (A pg. 29) H Select this to switch picture source type. (A pg. 30) I Current status area for the selected item. J Select this for Programme Playback. (A pg. 30) K Select this for Random Playback. (A pg. 30) L Select this to control the switching interval of the slide show.

(A pg. 30)

NOTE:

Although examples of the on-screen bar are provided here only for 3 types of discs, the on-screen bar will be displayed for whichever disc indicated in the left column.

Basic Operation On The On-screen Bar

Example: When selecting Picture Control function of DVD

During playback or while stopped

1 Press ON SCREEN twice to access the on-screen bar. The

item currently selected is highlighted and pointed by :.

ENTER

NAVIGATION

FGDE

RETURN

ON SCREEN

How To Access The On-screen Bar

1 Press ON SCREEN twice whenever a disc is loaded.

Contents of the on-screen bar during playback

DVD VIDE O

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

Video CD/SVCD

TRACK 99

VCD

3D-ON CINEMA AUTO

EACH 0:00

CINEMA

3D-ON CINEMA AUTO

2 Press DE to select AB, then press ENTER. The pop-up

window appears under the selected item.

3D-ON CINEMA AUTO

3 Press FG to select the desired option, then press ENTER.

3D-ON CINEMA AUTO

NORMAL CINEMA SHARP SOFT

To clear the on-screen bar Press ON SCREEN.

NOTE:

See the corresponding pages for details on each menu item.

Repeat Playback

You can repeat playback as you like according to the type of disc.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select A xB, then press ENTER. The pop-up

window appears under the selected item.

JPEG disc

JPEG

TRACK 99GROUP 99

5 SEC.

3D-ON CINEMA AUTO

3 Press FG repeatedly to select the desired Repeat mode, then

press ENTER.

28 EN

DVD-

VIDEO

CHAPTER 99 EACH 179:59GROUP 99

DVD-RAM/RW/R

BASIC OPERATIONS ON DVD DECK

OFF:

Repeat playback is not performed.

ALL REPEAT:

The whole disc is played back repeatedly.

TITLE REPEAT:

The current title is played back repeatedly.

DVD VIDE O

OFF:

Repeat playback is not performed.

TITLE REPEAT:

The current title is played back repeatedly.

CHAPTER REPEAT:

The current chapter is played back repeatedly.

Audio CD/Video CD/SVCD/JPEG/MP3

OFF:

Repeat playback is not performed.

ALL REPEAT:

The whole disc is played back repeatedly.

TRACK REPEAT*:

The current track is played back repeatedly.

*ATRACK REPEATB cannot be selected for JPEG discs.

To clear the on-screen bar Press ON SCREEN.

To cancel Repeat Playback

Repeat the above procedure from step 1, select AOFFB in step 3, then press ENTER.

NOTES:

● Repeat Playback is not possible for a Video CD/SVCD with PBC

function.

● Repeat Playback may not work properly depending on the type of

the disc being used.

● It is possible to use Mode Lock function. (A pg. 80)

A-B Repeat Playback

To cancel A-B Repeat Playback Press DE to select AA-B xB, then press ENTER.

NOTES:

● A-B Repeat Playback may not work properly depending on the

type of disc being used.

● The subtitles recorded around the A-B point may not appear.

● When the end of the item is reached before the end point is set,

the on-screen bar disappears from the TV screen. In such a case, repeat the procedure from step 1.

● The point B must be set at least 3 seconds after the point A.

● When playing back a DVD, A-B Repeat Playback is possible only

within the same title.

● AA-B xB cannot be selected during Programme and Random

Playback.

● AA-B xB cannot be selected while stopped.

Locating The Beginning Of A Desired Selection

You can locate the beginning of a title, chapter, group or track.

During playback or while stopped

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select A 9B, then press ENTER. 3 Press FG to select the desired item, then press ENTER.

● Skip this step for Video CD/SVCD and Audio CD.

For DVD-RAM/RW/R, DVD VIDEO

ATITLE SEARCHB or ACHAPTER SEARCHB is selectable. (However, ACHAPTER SEARCHB is not selectable while stopped.)

For JPEG, MP3

AGROUP SEARCHB or ATRACK SEARCHB is selectable. (However, ATRACK SEARCHB is not selectable while stopped.)

For Video CD/SVCD, Audio CD

ATRACKB is selectable.

NOTE:

Settings that are selectable during playback and stop mode differ depending on the type of disc and search used.

You can repeat the desired part.

During playback

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select AA-B xB. 3 Press ENTER at the beginning of the desired part you want to

repeat (point A). The elapsed playing time of the point A appears.

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

AB1:25:58 : :

3D-ON CINEMA AUTO

4 Press ENTER at the end of the desired part you want to repeat

(point B). The elapsed playing time of the point B appears.

● The selected part of the disc (between point A and B) is played

repeatedly.

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

AB1:25:58 1:40:00

To clear the on-screen bar Press ON SCREEN.

3D-ON CINEMA AUTO

CINEMA

TITLE SEARCH CHAPTER SEARCH

4 Press the number keys to enter the desired item number, then

press ENTER.

● Playback starts from the selected section.

Examples:

A To select track 5, press the number key A5B. B To select track 15, press the number key A1B and A5B. C To select track 25, press the number key A2B, then A5B.

If you have specified a wrong selection

Press RETURN on the remote control and repeat the above procedures from step 2.

To clear the on-screen bar Press ON SCREEN.

NOTES:

● When A7B is displayed on the TV screen in step 4, the chapter

you have selected is not contained in the disc, or chapter search does not work on the disc.

● Before you press ENTER, playback may start automatically when

you enter the section’s number depending on the disc.

● This function is not possible for a Video CD/SVCD with PBC

function.

BASIC OPERATIONS ON DVD DECK

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CHAPTER 99 EACH 0:00TITLE 99

EN 29

CABLE/SAT

DVDTV

0-9

CANCEL

ENTER

CLEAR

FGDE

RETURN

ON SCREEN

Time Search

You can play back a disc from the desired point by specifying the elapsed playing time from the beginning of a programme (DVD-RAM, DVD-R, DVD-RW, DVDVIDEO and HDD) or a disc (Video CD/SVCD and Audio CD).

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select Aj9B, then press ENTER. The pop-up

window appears under the selected item.

CHAPTER 99 EACH 0:00TITLE 99

DVD-

VIDEO

CINEMA AUTO

Simulated Surround Effect

It is possible to get a simulated surround effect from your stereo system. You can enjoy the virtual surround sound with your 2channel stereo system.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select AB, then press ENTER.

● A3D-ONB appears above the selected item and Simulated

Surround Effect is activated.

● Each time you press ENTER, A3D-ONB appears and disappears

alternately.

3D-ON CINEMA AUTO

To clear the on-screen bar Press ON SCREEN.

To cancel the simulated surround effect Press ENTER to clear A3D-ONB from the screen.

NOTES:

● Simulated Surround Effect works correctly only when playing

back a title recorded in multichannels.

● Simulated Surround Effect does not affect the DVD VIDEO

bitstream signal from the [DIGITAL AUDIO OUT] connectors.

● When Simulated Surround Effect is activated, the settings of

AANALOG AUDIO OUTB and AD. RANGE CONTROLB are disabled. (A pg. 71)

● Simulated Surround Effect cannot be activated under the

following conditions:

● When the HDD deck is in the recording mode.

● When the HDD or DVD deck is in the timer standby mode.

● When a disc containing both the Dolby Digital 5.1CH and 2CH

sound formats is playing back a scene that is not in the 5.1CH sound format.

Adjusting The Picture Quality

3 Press the number keys to enter the time, then press ENTER.

Playback starts from the specified time. Example: To play back from a point 12 (minutes): 50 (seconds) elapsed.

TIME

Press 1

If you have specified a wrong selection,

Press RETURN on the remote control and repeat the above procedures from step 2.

To clear the on-screen bar Press ON SCREEN.

NOTES:

● When A7B is displayed on the TV screen in step 3, you have

selected a point that exceeds the recording time of the disc.

● Some DVDVIDEO discs do not contain time information, and it is

not possible to use the Time Search function. In such cases, A7B is displayed on the TV screen as well.

● This function is not possible for a Video CD/SVCD with PBC

function.

TIME

Press 2

TIME

Press 0Press 5

You can obtain optimal picture quality by selecting an appropriate picture mode.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select AB, then press ENTER. The pop-up

window appears under the selected item.

CINEMA AUTO

3 Press FG to select the desired option, then press ENTER.

NORMAL:

Normally select this option.

CINEMA:

Suitable for a movie disc, etc.

SHARP:

Clearer, sharper-edged picture when viewing images with lots of flat, same-coloured surfaces such as cartoons.

SOFT:

Select this option when too much noise appears.

To clear the on-screen bar Press ON SCREEN.

30 EN

VCD

TRACK 99 EACH 0:00

JPEG

TRACK 99GROUP 99

BASIC OPERATIONS ON DVD DECK

Setting The Progressive Mode

You can obtain optimal picture quality by selecting whether the content on the disc is processed by field (video source) or by frame (film source).

1 Set the unit to the progressive scan mode. (A pg. 80) 2 Press ON SCREEN twice to access the on-screen bar. 3 Press DE to select AB, then press ENTER. The pop-up

window appears under the selected item.

CHAPTER 99 EACH 0:00TITLE 99

AUTO

CINEMA

DVD-

VIDEO

3D-ON

4 Press FG to select the desired option, then press ENTER.

AUTO:

This mode automatically detects film and video content for

progressive playback. When film content is found, flag

detection is used to invoke playback of film data in full screen.

When video content is found, pictures from multiple fields are

used to detect sections with movement, and then this

movement undergoes advanced image processing for output of

sharp, detailed progressive images without any reduction in

image quality where movement occurs. Normally, operation in

this mode is recommended.

FILM:

Suitable for playing back a progressive scanned film source

disc.

VIDEO:

Suitable for playing back a video source disc. The outlines on

the played back pictures will be soft.

To clear the on-screen bar Press ON SCREEN.

NOTE:

When the progressive mode is set, be sure to set AL-1 OUTPUTB to ACOMPONENTB (A pg. 63). Progressive scan is output only from

[COMPONENT VIDEO OUT] connectors.

Programme Playback

4 Press I. Playback starts in the programmed order.

● When all of the programmed tracks have been played back,

Programme Playback stops, but the programmed information remains.

● To add tracks to the end of the programme, perform steps 1

through 3.

● During Programme Playback, pressing T skips to the next

selection of the programme. Pressing S returns to the beginning of the current selection.

To clear the on-screen bar and the contents of the programme Press ON SCREEN.

To cancel Programme Playback Press DE to select APRGMB, then press ENTER.

NOTE:

Programme Playback is not possible depending on the type of disc.

Random Playback

You can play back all the tracks on the disc in random order.

While stopped

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select ARNDB, then press ENTER. Playback starts

in random order.

CINEMA

To clear the on-screen bar Press ON SCREEN.

To cancel Random Playback Perform steps 1 and 2.

NOTE:

The same track will not be played back more than once during Random Playback.

Select The Switching Interval Of The Slide Show

You can programme up to 30 tracks (Video CD/SVCD or Audio CD) to play back in the desired order.

While stopped

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select APRGMB, then press ENTER. The

programme table appears under on-screen bar.

TRACK 99 EACH 0:00

VCD

3 Press the number keys to

enter the track numbers in the

desired order. Examples: A To select track 5, press the

number key A5B and ENTER. B To select track 15, press the

number key A1B and A5B.

C To select track 25, press the number key A2B and A5B.

If you have specified a wrong selection

Press CANCEL(L). The last selection is erased. Or press CLEAR (o). The whole selection is erased.

USE [0-9] KEYS TO SELECT TRACK

Program Total Time

CINEMA

You can control the switching interval of the slide show.

1 Press ON SCREEN twice to access the on-screen bar. 2 Press DE to select AB, then press ENTER. The pop-up

window appears under the selected item.

5 SEC.

3 Press FG to select the desired option, then press ENTER.

● Each time you press FG, the interval changes as follows:

5 SEC. Y 10 SEC. Y 15 SEC. Y 20 SEC. Y 25 SEC. Y 30 SEC. Y (Back to the beginning)

To clear the on-screen bar Press ON SCREEN.

NOTE:

JPEG files are played back as a slide show. It may take more time to display an image with larger file size.

Parental Lock

This function restricts playback of DVDVIDEO discs which contain violent (and other) scenes according to the level set by the user. For example, if a movie which includes violent scenes supports the parental lock feature, such scenes which you do not want to let children view can be cut or replaced by other scenes.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press DVD so that the DVD lamp lights up on the unit.

CABLE/SAT

DVDTV

DVD

0-9

ENTER

FGDE

BASIC OPERATIONS ON DVD DECK

EN 31

8 Press FG to select your country code, then press ENTER.

● If you do not need to change your country code, jump to 10.

● See ACountry/Area Code List for Parental LockB (A pg. 87)

9 Press the number keys to enter the same password as in

step 6 above, then press ENTER.

10 Press SET UP to complete the setting.

NOTE:

Remember your password, or make a note of it.

To Change The Settings

You can change the Parental Lock settings later.

1 Perform steps 1 to 3 of ATo Set Parental Lock For The First

TimeB to access the APARENTAL LOCKB screen before continuing.

To change the level

2 Press FG to select APARENTAL LEVELB, then press ENTER. 3 Press FG to select the desired level, then press ENTER.

To change the country code

4 Press FG to select ACOUNTRY CODEB, then press ENTER. 5 Press FG to select your country code, then press ENTER.

● See ACountry/Area Code List for Parental LockB (A pg. 87).

6 Press the number keys to enter the same password as in

step 6 of ATo Set Parental Lock For The First TimeB, then press ENTER.

7 Press SET UP to complete the setting.

NOTE:

If you forget your password, enter A8888B in step 6.

SET UP

To Set Parental Lock For The First Time

While stopped

1 Press SET UP to access the Main Menu screen. 2 Press DE to select ADVD VIDEO SET UPB, then press G. 3 Press DE to select

APARENTAL LOCKB, then

press G.

4 Press FG to select

APARENTAL LEVELB, then

press ENTER.

5 Press FG to select the

desired level, then press

ENTER.

● The smaller the value of level

is, the more restrictive the

Parental Lock level becomes.

● Select ANONEB to cancel the restriction.

6 Press the number keys to enter your desired four-digit number,

then press ENTER.

● If you made a mistake, enter a correct number again.

7 Press FG to select ACOUNTRY CODEB, then press ENTER.

DVD VIDEO SET UP

HDD/DVD/DV SET UP

LANGUAGE SET

AUDIO OUTPUT

PARENTAL LEVEL

COUNTRY CODE

ENTER

SET UP

EXIT

SELECT

DVD VIDEO SET UP

HDD/DVD/DV SET UP

LANGUAGE SET AUDIO OUTPUT

PARENTAL LEVEL

COUNTRY CODE

ENTER

SET UP

EXIT

SELECT

INITIAL SET UP

FUNCTION SET UP

PARENTAL LOCK DISC PLAY SET UP

NONE

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

INITIAL SET UP

FUNCTION SET UP

PARENTAL LOCK DISC PLAY SET UP

NONE

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

To Temporarily Release Parental Lock

When you set the Parental Lock level strictly, some discs may not be played back at all. When you insert such a disc and try to play it back, the confirmation screen appears on the TV screen, asking you whether you want Parental Lock to be temporarily released or not.

1 Load a disc.

● If the disc is rated higher than the selected level, the

confirmation screen appears.

2 Press DE to select AYESB, then press ENTER.

● If you select ANOB, you cannot play back that disc.

3 Press the number keys to enter the same password as in

step 6 of ATo Set Parental Lock For The First TimeB, then press ENTER.

● When you enter the correct password, the Parental Lock is

released and the unit starts playback.

● If you enter a wrong password, AENTRY ERRORB appears on

the TV screen. Enter the correct password.

● If you have successively entered wrong password three times,

AENTRY ERROR CAN NOT CHANGE PASSWORDB appears on the TV screen. In such a case, press ENTER. The disc will stop. Then play back the disc again, and try the procedure again from step 1.

NOTE:

If you forget your password, enter A8888B in step 3.

32 EN

BASIC OPERATIONS ON DVD DECK

Basic Recording

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

ATTENTION:

It is not possible to record programmes on a DVD-R disc which has already been finalised.

DV/HDD/DVD REC MODE

INPUT SELECT JK

0-9

ENTER

R o

REC MODE

DVD

PR+/

WIo

CABLE/SAT

DVDTV

7 Press o twice to stop recording.

● It takes about 10 seconds to end the writing session when you

stop recording.

NOTES:

● It is recommended to format a DVD-RAM disc before use if you

use the disc on this unit for the first time.

● When using a brand-new DVD-RW disc, format the disc either in

VR mode or in Video mode. (A pg. 78)

● Recordings made on DVD-R/RW disc must be finalised to play

back on other DVD players. Perform AFinalise A Disc (DVD Deck Only)B (A pg. 79).

● You can record up to 99 programmes and 99 play lists on each

disc.

● Some programmes can only be recorded one time.

● When recording is started, an index of the first part of recording is

automatically recorded. (A pg. 49) To record satellite programmes, refer to page 48. To delete the index, refer to page 51.

● Recording sometimes may stop or cannot be performed even if

there is enough available capacity remaining on the disc.

● It is not possible to record on both DVD and HDD simultaneously.

Recording Mode

MPEG2 format is used as recording format. As a guide for picture quality, the AbpsB unit is used to represent how much data can be recorded per second. The larger this value is, the better the picture quality becomes but more capacity is required for the recording. Select XP or SP for programmes where quick movement occurs, such as sports programmes, and LP or EP for talk shows, etc. with relatively less movement. The recording modes for a 4.7 GB disc are set as follows:

Recording mode Recording amount

(approx.)

XP 10 Mbps 1 hour SP 5 Mbps 2 hours LP 2.5 Mbps 4 hours EP 1.6 Mbps 6 hours

60-360

(A pg. 34)

420 7 hours

The amount varies

depending on the

selected time.

480 8 hours

● For details on FR mode, refer to AFree Rate FunctionB (A pg. 34)

Maximum recording

time (approx.)

1 – 6 hours

1 Load a recordable disc.

● For details, refer to APlacing A DiscB (A pg. 8).

2 Press DV/HDD/DVD on the unit repeatedly or DVD on the

remote so that the DVD lamp lights up on the unit.

3 Press PR +/– or the number keys to select the channel you

wish to record. You can also press INPUT SELECT JK on the

unit to select.

4 Press REC MODE repeatedly to select the recording mode,

then press ENTER.

● Each time you press REC MODE, the recording mode changes

as follows:

XP N SP N LP NEP N FR (60-360*, 420, 480) N(Back to the

beginning)

* The value is selectable from 1 to 6 hours in 5-minutes interval by

pressing

DE repeatedly after selecting

value in 30-minutes interval, press and hold

For details on the recording mode, see the right column.

●

FR60–FR360B. To change the

DE.

5 Press R on the unit to start recording. Or while holding R, press

I on the remote control.

● The DVD recording lamp lights up on the unit.

6 Press R and W on the remote control simultaneously to pause

recording.

● To resume recording, press R and I simultaneously.

BASIC OPERATIONS ON DVD DECK

EN 33

Recording Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press DV/HDD/DVD on the unit repeatedly or DVD on the

remote so that the DVD lamp lights up on the unit.

DV/HDD/DVD

DISPLAY

TV AV / VIDEO

DVD

PR+/

CABLE/SAT

DVDTV

Instant Timer Recording (ITR)

This easy method lets you record for 30 minutes to 6 hours (selectable in 30-minutes interval), and shuts the unit off after recording is finished.

1 Press R on the unit to start recording. 2 Press R again to engage the ITR mode.

● On the front display panel, A0:30B appears.

3 If you want to record for more than 30 minutes, press R to

extend the time. Each press extends recording time by 30 minutes.

NOTES:

● You can only perform ITR using the R button on the unit.

● When the recording capacity becomes full during timer recording

or Instant Timer Recording, the unit automatically performs ARelief RecordingB (A pg. 46).

Watch Another Programme While Recording On The Unit

While recording is going on, you can watch another programme on the TV by using the TV’s tuner.

NOTE:

It is required that the remote control is set to be able to operate the TV in advance. (A pg. 67)

1 During recording, press TV AV/VIDEO to select TV mode.

● Video mode is disengaged, and the VIDEO indicator on the

front display panel lights off .

VIDEO indicator lights off.

REMAIN

DISPLAY

● The programme received on the TV’s tuner is displayed on the

TV screen.

2 Slide the TV/CABLE/SAT/DVD switch to TV. 3 Press PR +/– repeatedly to select the desired channel.

NOTE:

If a decoder is connected to the unit (A pg. 70), you can select a scrambled channel as well as other normal channels.

Elapsed Recording Time And Disc Remaining Time Indication

During recording, press DISPLAY repeatedly until the desired indication appears on the front display panel.

● Each time you press DISPLAY, the time indication changes as

follows: Elapsed recording time N Disc remaining time N Clock N (Back to the beginning)

● You can also check the disc remaining time by pressing REMAIN

while the unit is stopped or recording is in progress. The list of disc remaining times for all recording modes appears on the TV screen.

34 EN

BASIC OPERATIONS ON DVD DECK

Free Rate Function

To record the entire programme, the unit automatically sets the appropriate recording mode depending on the combination of the total time of the programme to be recorded and either the remaining disc space or the specified recording time (from 60 minutes to 480 minutes).

8 To record the entire programme within the actual

remaining disc space (DVD deck only)

Select AFR (JUST)B in a recording mode selection procedure.

● Note that this function is available only for timer programming

recording (A pg. 44, 46) and dubbing from HDD to DVD (A pg. 56).

8 To record the entire programme by specifying the desired

recording time

Select AFR60–FR360B, AFR420B or AFR480B in a recording mode selection procedure. (A pg. 32, 35, 44, 46)

8 To record a 25-min. long daily programme five times just

on the same DVD disc for example

Perfor m AS Be sure to set the recording mode to AFR125B and set Weekly/ Daily Rec Function to AMON-FRIB in step 8 to fit the total recording time to the whole disc space.

When the same programme is recorded in SP mode instead of in AFR125B, the 5th programme cannot be recorded.

HOWVIEW Timer ProgrammingB (A pg. 44) procedure.

A: 1st

Blank

B: 2nd C: 3rd D: 4th E: 5th

A: 1st B: 2nd C: 3rd D: 4th E: Blank (20 min.)

Receiving Stereo And Bilingual Programmes

Your unit is equipped with a Sound-Multiplex decoder (A2) and a Digital stereo sound decoder (NICAM) making reception of stereo and bilingual broadcasts possible. When the channel is changed, the type of broadcast being received will be displayed on the TV screen for a few seconds.

Type of Broadcast Being Received

On-Screen Display

A2 Stereo A2 Bilingual Regular Monaural NICAM Stereo NICAM Bilingual NICAM Monaural

NOTES:

● ASUPERIMPOSEB must be set to AONB or AAUTOB. Otherwise the

on-screen displays will not appear. (A pg. 73)

● If the quality of stereo sound being received is poor, the

broadcast might be received in monaural with better quality.

Selection Of The Audio Channel To Be Recorded On A Disc

When a programme is recorded on a DVD-RAM or DVD-RW disc in VR mode, all audio channels of the receiving programme are recorded on the disc. When you record a programme on a DVD-R or DVD-RW disc in video mode, select the desired audio channel (ANICAMB or AMONOB) to be recorded on the disc. (A pg. 72)

NOTE:

Before playing back a programme recorded in stereo, or a bilingual programme, refer to AAudio Channel SelectionB (A pg. 26).

NOTES:

● You can programme this unit to timer-record, regardless of the

disc remaining time. When the disc remaining time is not enough, the unit performs ARelief RecordingB (A pg. 46). To avoid this, make sure of the disc remaining time before setting timer programming. (Example) If you programmed to timer-record for 60 minutes in SP mode on a 120-minute disc, the disc remaining time would be 30 minutes in XP mode, 60 minutes in SP mode, 120 minutes in LP mode, 180 minutes in EP mode, and 240 minutes in FR480 mode. Timer-recording will not complete beyond these remaining times.

● The maximum recording time of FR (JUST) mode is the same as

the recording time of FR480 mode. When timer programming a long programme in FR (JUST) mode on a disc whose remaining time is short, it is recommended to check the disc remaining time in FR480 mode to see if the remaining time is enough for the programme.

● Even if more than one programme are timer programmed in FR

(JUST) mode, only the first one is recorded.

● In order to ensure that the recording fits on the disc, this feature

may leave a slight non-recorded section at the end of the disc.

● There may be some noise and sound disturbance at the point on

the disc where the unit switches the mode.

Basic Recording

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

ATTENTION:

The HDD on the unit requires approximately 20 seconds to start up after the unit has been turned on, during which no operation can be made.

HDD lamp

INPUT SELECT JK

HDD

0-9

DV/HDD/DVD

CABLE/SAT

PR+/

DVDTV

BASIC OPERATIONS ON HDD DECK

EN 35

Pause recording on HDD deck

It is not possible to pause recording. Pressing W initiates Live Memory Playback. However, it is still possible to pause recording only when recording the channels of external sources (AL-1B, AL-2B, AF-1B, and ADVB). While holding R, press W on the remote. To resume recording, while holding R, press I on the remote. No operation can be made with the buttons on the unit.

Recording Mode

Recording mode Maximum recording time (approx.)

XP 34 hours

SP 69 hours

LP 138 hours

EP 209 hours

FR480 300 hours

● For details on FR mode, refer to AFree Rate FunctionB (A pg. 34)

NOTE:

The maximum recording time stated in the above table are the approximate time under unused condition.

I o R

REC MODE

1 Press DV/HDD/DVD on the unit repeatedly or HDD on the

remote so that the HDD lamp lights up on the unit.

2 Press PR +/– or the number keys to select the channel you

wish to record. You can also press INPUT SELECT JK on the

unit to select.

3 Press REC MODE repeatedly to select the recording mode,

then press ENTER.

● Each time you press REC MODE, the recording mode changes

as follows:

XP N SP N LP NEP N FR (60-360*, 420, 480) N (Back to the

beginning)

* The value is selectable from 1 to 6 hours in 5 minutes interval by

● For details on the recording mode, see the right column.

DE repeatedly after selecting

pressing value in 30 minutes interval, press and hold

FR60–FR360B. To change the

DE.

4 Press R on the unit to start recording. Or while holding R, press

I on the remote control.

● The HDD recording lamp lights up on the unit.

5 Press o twice to stop recording.

● Pressing o once displays the confirmation message to stop

recording. Press o again to terminate recording.

NOTES:

● Continuous recording for over 48 hours is not possible.

● It is not possible to record on both DVD and HDD simultaneously.

36 EN

BASIC OPERATIONS ON HDD DECK

Recording Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press DV/HDD/DVD on the unit repeatedly or HDD on the

remote so that the HDD lamp lights up on the unit.

DISPLAY

TV AV / VIDEO

HDD lamp

INPUT SELECT JK

HDD

REMAIN

DV/HDD/DVD

CABLE/SAT

PR+/

DISPLAY

DVDTV

Watch Another Programme While Recording On The Unit

While recording is going on, you can watch another programme on the TV by using the TV’s tuner.

NOTE:

It is required that the remote control is set to be able to operate the TV in advance. (A pg. 67)

1 During recording, press TV AV/VIDEO to select TV mode.

● Video mode is disengaged, and the VIDEO indicator on the

front display panel lights off.

VIDEO indicator lights off.

● The programme received on the TV’s tuner is displayed on the

TV screen.

2 Slide the TV/CABLE/SAT/DVD switch to TV. 3 Press PR +/– or INPUT SELECT JK repeatedly to select the

desired channel.

NOTE:

If a decoder is connected to the unit (A pg. 70), you can select a scrambled channel as well as other normal channels.

Elapsed Recording Time And Disc Remaining Time Indication

During recording, press DISPLAY on the remote control or the unit repeatedly until the desired indication appears on the front display panel.

● Each time you press DISPLAY, the time indication changes as

follows: Elapsed recording time N Disc remaining time N Clock N (Back to the beginning)

● You can also check the disc remaining time by pressing REMAIN

while the unit is stopped or recording is in progress. The list of disc remaining times for all recording modes appears on the TV screen.

Instant Timer Recording (ITR)

This easy method lets you record for 30 minutes to 6 hours (selectable in 30-minutes interval), and shuts the unit off after recording is finished.

1 Press R on the unit to start recording. 2 Press R again to engage the ITR mode.

● On the front display panel, A0:30B appears.

3 If you want to record for more than 30 minutes, press R to

extend the time. Each press extends recording time by 30

minutes.

NOTES:

● You can only perform ITR using the R button on the unit.

● When the recording capacity becomes full during timer recording

or Instant Timer Recording, the unit is automatically shut off.

Receiving Stereo And Bilingual Programmes

Type of Broadcast Being Received

A2 Stereo A2 Bilingual Regular Monaural NICAM Stereo NICAM Bilingual NICAM Monaural

NOTES:

● ASUPERIMPOSEB must be set to AONB or AAUTOB. Otherwise the

on-screen displays will not appear. (A pg. 73)

● If the quality of stereo sound being received is poor, the

broadcast might be received in monaural with better quality.

On-Screen Display

BASIC OPERATIONS ON HDD DECK

EN 37

Basic Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

DV/HDD/DVD

CABLE/SAT

HDD

NTER

Playback Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press HDD so that the HDD lamp lights up on the unit.

CABLE/SAT

DVDTV

HDD

WIo

DVDTV

O/SLOW

JUMP

JUMP +

Variable Speed Search

During playback, press N for forward variable speed search, or O for reverse variable speed search.

● Each press of the button increases the search speed for each

direction.

● To resume normal playback, press I.

Reverse

MARK

T N/SLOW +

ON SCREEN

Forward

ATTENTION:

● It may take a few seconds to start playback. This is not a

malfunction.

● Forward/reverse high-speed search and other operations

cannot be performed while playback is stopped.

1 Press DV/HDD/DVD on the unit repeatedly or HDD on the

remote so that the HDD lamp lights up on the unit.

2 Press I to start playback.

● The Library Database Navigation also enables you to search

and select the desired programmes. (A pg. 50)

3 Press W to pause playback.

● To resume normal playback, press I.

4 Press o to stop playback.

NOTE:

When the Library Database Navigation screen appears, choose a thumbnail image of the desired title on the TV screen, then press ENTER. (A pg. 50)

Reverse Search

4 steps

-60 -15 -3

-5

Reverse

Slow Motion

Play

3 steps

-1 1 1.5 3 5 15

1161

Slow Motion

3 steps

Normal

Forward Search

Play

5 steps

NOTE:

You can hear the (normal) audio track only during 1.5x speed search.

Still Picture/Frame-By-Frame Playback

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) to activate frame-by-

frame playback.

● Each press of SLOW – (O) or SLOW + (N) advances/

reverses the still picture frame by frame.

● To resume normal playback, press I.

Slow Motion

1 Press W to pause during playback. 2 Press SLOW – (O) or SLOW + (N) for 2 or more seconds.

● Each press of SLOW – (O) or SLOW + (N) increases the

slow motion speed for each direction.

Skip Search

During playback, press v.

● Each press initiates an approximately 30-second period of fast-

motion playback. Normal playback resumes automatically.

38 EN

BASIC OPERATIONS ON HDD DECK

Instant Replay

You can move back the playback position slightly. Press w on the remote control or INSTANT REPLAY on the unit.

● Each press skips back for approximately 7 seconds and resumes

playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

1.5x Speed Playback

You can play back a title quickly. The sound will also be played back faster than normal speed during 1.5x speed playback.

1.5x speed playback cannot be performed during recording on HDD or DVD.

1 Press O to locate the point to start 1.5x speed playback from. 2 Press I to resume playback. 3 Press N once.

● Pressing ON SCREEN displays AX1.5B on the top right corner of

the screen.

NOTE:

When the unit is connected with a digital audio device using an optional optical cable, set ADIGITAL AUDIO OUTB to APCM ONLYB. (A pg. 26)

Jump Search

You can locate a scene ahead or behind the current one by jumping scenes according to selected time intervals (A pg. 73) during playback (or Live Memory Playback). Press JUMP – or JUMP +.

● To advance forward or back, press JUMP – or JUMP +

repeatedly within 5 seconds of each press to continue jump.

● Depending on the time from where you want to start jump search,

● When you cannot advance any further (beginning or end of

programme reached), the message AUNABLE TO GO BACK ANY MOREB appears on the screen and the on-air screen resumes. In such a case, press S, O or o.

Example:

Playback search when jump interval is set to 15 MIN jumps. Taking for instance, you want to start jump search 40 minutes after the beginning of the programme. Pressing JUMP – or JUMP + will result in a jump to the scene at the 30 minutes point or 45 minutes point respectively as illustrated below. At the subsequent press, the scene will jump to the 15 minutes point or 1 hour point respectively, according to the selected time interval, which in this case is A15 MINB.

Time counter

0 min

15 min

30 min

40 min

45 min

1 h 15 min

1 h

Marking Positions To Play Back Again Later

It is possible to mark positions (up to 999 points) where you want to play back once again later, and start playback from a marked position. Marking onto the disc when recording is helpful to locate a start point when you play back the disc later.

To mark positions:

During playback, press MARK at positions you want to mark.

● AMARKB appears on the TV screen.

You can easily locate the marked positions using S or T when you play back the disc.

To delete the marked positions:

While paused, press S or T to locate a marked position you want to delete, then press MARK.

● Crossed AMARKB appears on the

TV screen, and the marked position is deleted.

NOTE:

When a monaural programme changes to a stereo programme while recording, a mark signal is automatically recorded.

Beginning of programme

Current scene

End of programme

Basic Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

DV/HDD/DVD I

CABLE/SAT

BASIC OPERATIONS ON DV DECK

EN 39

1 Load a cassette. Make sure the window side is up, the rear

label side is facing you and the arrow on the front of the cassette is pointed toward the unit.

● Do not apply too much pressure when inserting.

● If the erase protection switch is set to ASAVEB, playback begins

automatically. It takes about 15 seconds until the playback picture appears. However, when APOWER SAVEB is set to AONB (A pg. 73), playback will not begin automatically even though a cassette with its erase protection switch set to ASAVEB is inserted.

● The unit’s power comes on automatically.

2 Press DV/HDD/DVD on the unit repeatedly or DV on the remote

so that the DV lamp lights up on the unit.

3 Find the programme start point. If the tape is advanced past the

start point, press O. To go forward, press N.

DVDTV

4 Press I to start playback. 5 Press o to stop playback.

● To eject the cassette, press M (DV).

Clean the video heads using a dry cleaning cassette

- M-DV12CL - when:

● No picture during playback.

● Block noise appears during playback.

● AUSE CLEANING CASSETTEB appears on the screen.

NOTE:

The heads get dirty in the following cases:

● in an environment prone to extreme temperature or humidity

● in a dusty environment

● flaw, dirt or mould on video tapes

● continuous usage for a long time

Usable cassettes

● Cassettes marked P can be used with the DV deck.

● Tapes recorded in the DVCAM format can be played.

NOTES:

● When you record a tape on the DV deck with the recording speed

set to ALPB, it is recommended to play back that tape back on this DV deck. Digital video recorder from other manufacturers may not be able to play back the tape properly.

Accidental erasure prevention

To prevent accidental recording on a recorded cassette, set its erase protection switch to ASAVEB. To record on it later, set the switch to ARECB.

Erase protection switch

40 EN

BASIC OPERATIONS ON DV DECK

Playback Features

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press DV/HDD/DVD on the unit repeatedly or DV on the

remote so that the DV lamp lights up on the unit.

CABLE/SAT

DVDTV

DISPLAY

AUDIO

Skip Search

During playback, press v.

● Each press initiates an approximately 30-second period of fast-

motion playback. Normal playback resumes automatically.

Instant Replay

During playback, press w on the remote control or

INSTANT REPLAY

(about 7 seconds) and resumes playback.

on the unit. The unit rewinds the picture a little

Next Function Memory

The Next Function Memory AtellsB the unit what to do after rewinding. Before continuing, make sure the unit is in the Stop mode.

For Automatic Start Of Playback

Press O, then press I within 2 seconds.

Soundtrack Selection

Your unit is capable of recording two soundtracks (L and R) and will play back the one you select.

During Playback Pressing AUDIO changes the soundtrack as follows:

TRACK

On-Screen Display

L W X R For stereo or Bilingual tapes L W For main audio of Bilingual tapes

X R For sub audio of Bilingual tapes

NOTE:

For instructions on recording stereo and bilingual programmes, refer to page 34.

USE

ATTENTION:

In the search, still, slow-motion or frame-by-frame playback mode, a slight mosaic effect appears on screen.

Variable Speed Search

During playback, press N for forward variable speed search, or O for reverse variable speed search.

● Each press of the button increases the search speed for each

direction.

● To resume normal playback, press I.

Reverse

Reverse Search

3 steps

Slow Motion

Reverse

1 step

Slow Motion

1 step

Normal Play

Forward

Forward Search

3 steps

12412

Still Picture/Frame-By-Frame Playback

1 Press W to pause during playback. 2 Press W to activate frame-by-frame playback.

● To resume normal playback, press I.

Slow Motion

1 Press W to pause during playback. 2 Press and hold W for 2 seconds, then release. Press W and

release again to return to still picture.

● Press N for forward slow motion or O for reverse slow

motion.

● To resume normal playback, press I.

Time Code

During recording, a time code is recorded on the tape. This time code is used to confirm the position on the tape when playing back or editing a tape.

1 Press DISPLAY on the remote control or the unit until the time

code on the tape appears on the front display panel and the TV screen.

● Each time you press DISPLAY, the indication changes as

follows: Tape remaining time N Time code N Clock time N (Back to the beginning)

LIVE MEMORY PLAYBACK ON HDD/DVD DECK

EN 41

Live Memory Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press DV/HDD/DVD on the unit repeatedly to select the HDD

or DVD deck.

This unit records pictures onto the hard disc and DVD-RAM disc, instead of video tapes, then plays back the pictures recorded on the disc. This makes it possible to achieve high-speed writing and read-out that has not been possible with conventional VCRs, enabling recording and playback simultaneously.

High-speed spin

Recording

(High-speed writing)

It is called ALive Memory PlaybackB to start playback of the programme being recorded, with a time-lag between a recording point and a playback point, as shown in the figure below.

Current playback point

(Live Memory Playback)

Current recording position

Playback continues

(Recording point)

Recording start point

Currently elapsed recording time

30 min.

Not only can this unit play back a programme previously recorded while recording or timer recording another programme, but the unit also allows you to play back from the beginning of a programme while continuing to record the same programme.

Playback (High-speed read-out)

Recording continues

1 hour

Recording/playback Status Display

CABLE/SAT

DVDTV

LIVE NAVIGATION

Press NAVIGATION

Navigation menu, then choose a programme to play back. (A pg. 49)

ON SCREEN

Live Memory Playback status can be checked by pressing ON SCREEN to display the bar meter on the superimpose display. The current status is superimposed on the TV screen. ( using Live Memory playbackB)

NOTES:

● Live Memory Playback could be performed approximately 30

seconds after recording has started on the DVD-RAM disc. However, for HDD, Live Memory Playback is possible right after recording has started.

● Although high-speed search up to approximately 30 seconds

before the current recording point is possible during Live Memory Playback, once the current recording point is reached, the unit resumes normal playback and maintains a delay of approximately 30 seconds so that recording and playback can continue.

● When using Live Memory Playback during timer recording,

playback continues even after the end of the recording.

● When using Live Memory Playback during timer recording,

playback is automatically stopped just before recording starts, and then recording starts when the time arrives for the next timerprogramme.

● It is impossible to perform ITR even if you press R during Live

Memory Playback. (A pg. 36) Press o to display the programme being recorded, then perform ITR settings.

● Playback may be paused for a moment during Live Memory

Playback, which does not interfere with recording.

● Live Memory Playback cannot be performed while recording the

source from DV input. (A pg. 59, ADV Dubbing (HDD & DVD Deck Only)B)

● When LIVE CHECK is pressed to display the picture currently

being recorded, the picture size may not be correct.

● Press R or LIVE to stop Live Memory Playback.

● Live Memory Playback cannot be performed even if the ALIVE

MEMORYB in AHDD SET UPB is set to other than AOFFB, as temporary recording on HDD stops during recording on DVD.

to display Library Database

A pg. 14, AWhen

42 EN

LIVE MEMORY PLAYBACK ON HDD/DVD DECK

Buttons To Be Used During Live Memory Playback

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press HDD or DVD to select the desired deck for Live Memory

Playback.

CABLE/SAT

DVDTV

HDD

E G

A LIVE

Returns to on air programme screen. When a confirmation

message appears by pressing this button during timer

programming or title editing, etc., follow the instruction to return

to the previous screen.

B NAVIGATION

Displays Library Database Navigation menu. You can choose a

title to play back.

C S

● Pressing once skips back to the beginning of the chapter being

played back.

● Pressing down for 2 or more seconds during playback reverses

playback at 5 times the normal speed while pressed. Releasing

the button resumes normal playback.

Available only when paused

● Pressing down for 2 or more seconds reverses playback at 1/16

times the normal speed.

D T

● Pressing once skips forward to the beginning of the next

chapter being played back.

● Pressing down for 2 or more seconds during playback

advances playback at 5 times the normal speed while pressed.

Releasing the button resumes normal playback.

Available only when paused

● Pressing down for 2 or more seconds advances playback at 1/

16 times the normal speed.

E O

● Each press of the button during playback advances the

playback speed in 5 steps in the reverse direction.

Available only when paused

● Each press of the button reverses the still picture frame by

frame.

● Pressing down for 2 or more seconds reverses playback at 1/16

times the normal speed. Then, each press of the button

reverses slow-motion at 1/16 times, 1/4 times and 1/2 times the

normal playback.

F H K

DVD

F N

● Each press of the button during playback advances the

playback speed in 4 steps in the forward direction.

Available only when paused

● Each press of the button advances the still picture frame by

frame.

● Pressing down for 2 or more seconds advances playback at 1/

16 times the normal speed. Then, each press of the button advances slow-motion at 1/16 times, 1/4 times and 1/2 times the normal playback.

G o

● Pressing once during Live Memory Playback or RetroActive

Recording returns to the screen on air.

● Pressing twice during recording stops recording and returns to

the screen on air.

H W

● Pressing once pauses playback (still picture playback).

● Pressing repeatedly advances the still picture frame by frame.

I JUMP –

Each press of the button during Live Memory Playback jumps back for the selected time interval and resumes playback. (A pg. 38, AJump SearchB)

J JUMP +

Each press of the button during Live Memory Playback jumps forward for the selected time interval and resumes playback. (A pg. 38, AJump SearchB)

K v

It is useful when skipping over unwanted sections.

● Pressing once skips forward for approximately 30 seconds and

resumes playback.

● Pressing repeatedly skips forward continuously as many times

as pressed.

L w

It is useful when watching sports programmes, etc.

● Each press skips back for approximately 7 seconds and

resumes playback.

● Pressing repeatedly skips back for approximately 7 seconds

continuously as many times as pressed.

M LIVE CHECK

You can check, for example, if the programme you are recording has already finished.

● Pressing once displays the picture currently being recorded and

the one being played back simultaneously.

● Pressing successively clears the Live Check window and

displays only the picture currently being played back.

LIVE MEMORY PLAYBACK ON HDD/DVD DECK

EN 43

Temporary recording for Live Memory (HDD deck only)

This unit automatically records the channel being received, within the specified range of time, to the reserved space on the hard disc. The time range can be set for 30 minutes, 1 hour, and 3 hours. (A pg. 72)

NOTE:

Previous temporary recordings will be overwritten since the unit is always recording the channel being received. Thus, it is not possible to play back TV programmes recorded beyond the specified range of time since they are already overwritten. To avoid this in order to save titles, perform normal recording (A pg. 35), timer recording (A pg. 44, 46), or RetroActive Recording (A pg. 43).

About limitation on temporary recording

The temporary recording for Live Memory is cancelled in the following cases, and will start all over again when it is to resume.

● When the power is turned off

● When the system is powered again after a power failure was

occurred

● When normal recording, timer recording, RetroActive

Recording, or Automatic Satellite Programme Recording (A pg. 48) is performed

● When the ALIVE MEMORYB setting is changed (A pg. 72)

● When tuner channel setting is performed (A pg. 74)

● When dubbing is performed by pressing DUBBING (A pg. 56)

● When ADVB is selected by pressing PR +/– (A pg. 59)

RetroActive Recording (HDD deck only)

You can start recording from the previous part of the channel you are currently watching (temporarily recorded on the background). (A pg. 43, ATemporary recording for Live Memory (HDD deck only)B)

1 Press S or O to locate the point to start recording from.

● Each press of O increases the reverse search speed.

2 Press R on the unit to start RetroActive Recording. Or while

holding R, press I on the remote control.

3 Press o to stop RetroActive Recording.

● The on-air screen resumes.

NOTES:

● You cannot use RetroActive Recording for channels other than

the channel you are currently watching.

● Recording speed is automatically set to FR65 mode when

RetroActive Recording is started.

● Temporarily recorded data prior to the beginning of RetroActive

Recording is erased when RetroActive Recording started.

Simultaneous Recording and Playback

You can play back the previous part of the channel you are recording or other programmes available in the Library Database.

1 Press NAVIGATION. The Library Database Navigation screen

appears.

2 Press DE to select AORIGINALB, then press ENTER. 3 Press FGD E to select the desired title, then press ENTER.

● For DVD-RAM, playback starts from the beginning of the title if

ACONTINUOUS PLAYB in ADVD SET UPB is set to AONB (A pg. 72).

4 Press DE to select the desired playback method

(ABEGINNINGB, ARESUMEB or AREPEATB), then press ENTER.

● Playback of the selected title begins automatically.

5 Press o to stop playback.

● The on-air screen resumes.

NOTES:

● You can use various playback features during Live Memory

Playback.

● To stop simultaneous playback, press o. The on-air screen

resumes. To stop actual recording, press o again.

Instant Replay

You can move back the playback position slightly during recording or Live Memory Playback. Press w on the remote control or INSTANT REPLAY on the unit.

8 DVD-RAM

● Pressing once during recording skips back for approximately 30

seconds and starts Live Memory Playback. While pressing once during Live Memory Playback skips back for approximately 7 seconds and resumes playback.

● Each subsequent press skips back for approximately 7 seconds

and resumes playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

8 HDD

● Pressing during recording skips back for approximately 7

seconds and starts Live Memory Playback. While pressing during Live Memory Playback skips back for approximately 7 seconds and resumes playback.

● Each press skips back for approximately 7 seconds and resumes

playback.

● Pressing while paused skips back for approximately 7 seconds

and resumes pause.

Resuming Playback (HDD deck only)

You can resume playback of a TV broadcast you were recording or watching from the point you have paused.

1 Press W to pause a TV broadcast.

● Recording continues when recording.

2 Press I to start Live Memory Playback.

● Playback resumes from the paused position.

3 Press o to resume the on-air screen.

44 EN

TIMER RECORDING ON HDD/DVD DECK

SHOWVIEW Timer Programming

You can programme this unit to timer-record as many as 16 programmes. With the S simplified because each TV programme has a corresponding code number which your unit is able to recognise. You can use the remote control to enter the S

● Make sure that the unit’s built-in clock is set properly.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

1 Load a recordable disc if recording to DVD. 2 Press PROGRAMME to access the programme top screen. 3 Press FGD E to select ASHOWVIEWB, then press ENTER.

● When APROGRAMME FULL DELETE UNWANTED TIMER

4 Press the number keys to

● If you have made a mistake, press FGD E to select ADELETEB

5 Press FG to select ARECORD TOB, then press ENTER. Press

6 Press FGD E to select ACONFIRMB, then press ENTER.

● If the number you entered is invalid, ASHOWVIEW NO. ERROR

● If AGUIDE PROGRAMME IS NOT SET SET GUIDE

HOWVIEW system, timer programming is greatly

HOWVIEW number.

CABLE/SAT

DVDTV

0 – 9

PROGRAMME

ENTER

DISPLAY

VPS/PDCj

FGDE

RETURN

PROGRAMMESB appears on the TV screen, you need to

cancel some of the reserved programmes. (A pg. 47)

PROGRAMME > SHOWVIEW (1/2)

enter the S

HOWVIEW number

of a programme you wish to

record.

Press FGD E to select the

desired number key on the

screen, then press ENTER.

SELECT WITH @ THEN PRESS [ENTER]

PRESS [PROGRAMME] TO EXIT

PROGRAMME

SHOWVIEW NO.

1234

12 456 789

DELETE

DELETE ALL

RECORD TO DVD

ENTER

SELECT

EXIT

CONFIRM

Repeat to enter all required

numbers.

or ADELETE ALLB, then press ENTER and input the correct

number before you press ENTER again.

FG to select the desired recording deck, then press ENTER.

CONFIRM SHOWVIEW NO. THEN RETRYB appears on the TV

screen. Input a valid S

HOWVIEW number.

PROGRAMME THEN RETRYB appears on the TV screen, set

Guide Programme Numbers manually. (A pg. 74)

7 The SHOWVIEW number you entered and the matching timer-

recording information are displayed on the TV screen. Check the programme data.

● To cancel this setting, press RETURN.

IMPORTANT:

Make sure the channel position number you wish to record is displayed; if not, see AS

HOWVIEW System SetupB (A pg. 74) and

set the Guide Programme number correctly.

8 Press FG to select the desired recording option as required.

Press FG to select the desired setting, then press ENTER.

● AINPUT TITLEB (A pg. 50, AModify Title NameB)

● ACATEGORYB (A pg. 51, AModify CategoryB)

● AVPS/PDCB (A pg. 45, AVPS/PDC RecordingB)

● AWEEKLY/DAILYB (A pg. 45, AWeekly/Daily RecordingB)

● AREC MODEB (A pg. 32, ARecording ModeB)

9 Press FG to select AOKB, then press ENTER to access the

Programme Confirmation screen.

10 Press DE to select AEXITB, then press ENTER to complete

timer programming.

● To programme another timer, press DE to select

ACONTINUEB, then press ENTER.

● If APROGRAMME OVERLAPPEDB appears on the TV screen,

delete or modify the programmes.

NOTES:

● There may be cases that the SHOWVIEW Timer Programming

function prolongs the stop time of the programming.

● When two successive programmes are recorded on a DVD-RW

disc with the S beginning of the second one may be left off the recording.

● If the copy limited programme is received during timer-recording,

the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed.

IMPORTANT:

If you have moved to a different area or if a broadcasting station’s channel number has been changed, the wrong channel number will be displayed on the S in step 7. When this happens, set the correct Guide Programme number for that station. (A pg. 74, AS

Satellite Receiver Users

To timer-record a satellite broadcast using the S system:

A Perform AS B Set the satellite receiver to the appropriate channel before

the selected programme begins.

C Leave the satellite receiver’s power on.

HOWVIEW Timer Programming function, the

HOWVIEW programme screen

HOWVIEW System SetupB)

HOWVIEW

HOWVIEW Timer ProgrammingB (A pg. 44).

TIMER RECORDING ON HDD/DVD DECK

EN 45

Weekly/Daily Recording

You can record programmes with one of the following weekly/daily timer settings.

For the HDD deck

When you select a mode other than ONCE, the space on the hard disk drive is saved for new recordings by overwriting previous recordings. To prevent loss of a needed recording, backup programmes you wish to save by dubbing them to DVD discs before overwriting previous recordings. Or save the title of weekly/ daily programmes to avoid overwriting of a previous week/day. (A pg. 47)

ONCE (One Time Recording)

In this mode a programme will not be automatically overwritten.

WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite)

When the set weekly programme is broadcast, the programme

recorded last week is automatically deleted and overwritten by

the new programme. Save the title of each programme you

wish to save, then the recorded programme is saved and will

not be overwritten by the new programme.

This week’s drama

Overwritten

MON-SUN (FOR A WEEK)/ MON-SAT (FOR A WEEK)/ MON-FRI (FOR A WEEK) (Daily Recording/Weekly Overwrite)

When the set weekly programme is broadcast, the programme

recorded on the same day last week is automatically deleted

and overwritten by the new programme. Save the title of each

programme you wish to save, then the recorded programme is

saved and will not be overwritten by the new programme.

This

Overwritten

week

Last

week

MON-SUN (OVERWRITE)/ MON-SAT (OVERWRITE)/ MON-FRI (OVERWRITE) (Daily Recording/Daily Overwrite)

When the set daily programme is broadcast, yesterday’s

programme is automatically deleted and overwritten by the new

programme. Save the title of each programme you wish to

save, then the recorded programme is saved and will not be

overwritten by the new programme.

Last week’s drama

MON TUE WED THU FRI

VPS/PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) and VPS (Video Programme System) are services designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video unit and have precedence over the advertised times you may have preset into the timer. This means that your unit will start and stop recording when the preset TV programmes actually start and end^even if the broadcast time of a preset TV programme is changed.

NOTES:

● Make sure to press VPS/PDCj after completing timer

programming procedure to activate the VPS/PDC recording function. The VPS/PDC recording indicator lights up on the front display panel when VPS/PDC recording function is activated. However, it will blink rapidly when VPS/PDCj is pressed under the following conditions:

● Clock is not set.

● Timer programming has not been set.

● Disc is not loaded.

● HDD is full.

● When you use Manual Timer Programming, set the start time

(VPS or PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

● VPS/PDC recording is also possible when a satellite receiver or a

cable system is connected to [L-2 IN/DECODER] connector on your unit.

● VPS/PDC recording is also possible via the [L-1 IN/OUT]

connector.

● When timer recording via VPS/PDC recording is in progress, it is

not possible to switch between the HDD and DVD deck, and the following menus cannot be displayed:

● Main Menu

● Library Database Navigation menu

● Editing menu

● If the unit is powered on when set to record a timer programme

onto HDD/DVD using VPS/PDC, the PDC information will not be used. The programme will be recorded using the start and stop times originally programmed.

How to check if the station being received transmits a VPS/ PDC signal

A Hold down DISPLAY for about 5 seconds. AVPS/PDCB appears

and blinks on the front display panel. If a VPS/PDC signal is detected from the station, AVPS/PDCB will stop blinking. If no VPS/PDC signal is detected from the station, AVPS/PDCB will blink at a slower rate.

B Press DISPLAY again to return to normal display.

Overwritten

Tuesday’s programme

Monday’s programme

For the DVD deck

ONCE (One Time Recording) WEEKLY (Weekly Recording) MON-SUN/ MON-SAT/ MON-FRI (Daily Recording)

46 EN

TIMER RECORDING ON HDD/DVD DECK

Manual Timer Programming

You can programme this unit to timer-record as many as 16 programmes. If you do not know the S wish to record, use the following procedure to set your unit to timer-record the programme.

● Make sure that the unit’s built-in clock is set properly.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

ENTER

HOWVIEW number for the programme you

CABLE/SAT

DVDTV

PROGRAMME

FGDE

8 Press FG to select ATV PROGB, then press ENTER. Press

FG to select the desired channel.

9 Press FG to select ACONFIRMB, then press ENTER. 10 Set the other recording options as required.

● Refer to step 8 in ASHOWVIEW Timer ProgrammingB

(A pg. 44).

11 Press FG to select AOKB,

then press ENTER to access the Programme Confirmation screen.

12 Press DE to select AEXITB,

then press ENTER to complete timer programming.

● To programme another timer,

press DE to select ACONTINUEB, then press ENTER.

● If APROGRAMME OVERLAPPEDB appears on the TV screen,

delete or modify the programmes.

NOTES:

● When two successive programmes are recorded on a DVD-RW

disc with Manual Timer Programming function, the beginning of the second one may be left off the recording.

● If the copy limited programme is received during timer-recording,

the unit enters Record Pause mode. Recording starts again if it is switched to a recordable broadcast during the time you programmed.

SELECT WITH @ THEN PRESS [ENTER]

PRESS [PROGRAMME] TO EXIT

PROGRAMME

EXIT

PROGRAMME > CALENDAR PR. (3/3)

14/01/04 WED 22:30 - 23:00 GARDENING [EDUCATION]

INPUT TITLE

CATEGORY

PLAY LIST

DISC No.

NAME

When a disc that is not registered in the library is loaded, a message appears confirming if the disc should be registered. If registering, perform the following procedure.

1 Press DE to select AREGISTERB, then press ENTER to confirm

the registration.

2 Press NAVIGATION to return to the normal screen.

NOTES:

● It is not possible to register discs formatted on devices other than

JVC’s DVD recorders.

● It is not possible to register discs recorded on devices other than

JVC’s DVD recorders.

● It is not possible to register discs when ASAVE AS LIBRARYB is

set to AOFFB. (A pg. 72)

NAVIGATION ON HDD/DVD DECK

EN 55

Playback With MP3/WMA/JPEG Navigation

This unit can play back discs that MP3/WMA sound files and JPEG image files taken with digital still cameras or other devices are recorded. The MP3/WMA/JPEG Navigation enables you to search and select the desired files recorded on CD-R/RW or CD-ROM discs very easily.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Press DVD to select the DVD deck.

NAVIGATION > ORIGINAL

GROUP : 001/100 TRACK : 001/100 IT’S SHOWTIME!!/B’z

ROOT CLASSIC CLUB DANCE EUROPE FOREIGN GROUP FOREIGN ROCK

001.

IT’S SHOWTIME! !/B’z

002.

ONLYFLOWER IN THE WORLD/SMAP

003.

SEXY GUY/GOMAKI

004.

HEY?/AYAYA

005.

DOOR TOTOMORROW/ IWISH

REASON/ASAMI

006.

007.

DIE ANOTHERDAY/ JAMESBOND

A Selected group number/total number of groups on the disc B Selected file number/total number of files in the group that

contains the selected file

C Elapsed time (MP3 only) D Name of the selected file E Group name F Selected file

0: 07: 01

Locating The Desired Group And Tracks

1 Load a disc. 2 Press NAVIGATION. 3 Press FGD E to select AORIGINALB, then press ENTER. 4 Press FG to select the

desired group, then press ENTER.

● A list of files in the selected

group appears.

5 Press FG to select the

desired item, then press ENTER. The unit starts playback from the selected item.

● The unit stops when all items

in the selected group are played back.

NOTES:

● If you press SELECT(I) instead of ENTER in step 4, the unit

starts playback from the first file of the group.

● JPEG files are played back as a slide show at the set intervals.

(A pg. 30)

● If a file name includes any 2-byte character, the unit may not

show the file name correctly.

● The order of the groups and items shown in steps 4 and 5 may

differ from the order shown on your PC.

NAVIGATION > ORIGINAL

GROUP : 001/100 TRACK : 001/100 IT’S SHOWTIME!!/B’z

ROOT CLASSIC CLUB DANCE EUROPE FOREIGN GROUP FOREIGN ROCK

GROUP : 001/100 TRACK : 001/100 IT’S SHOWTIME!!/B’z

ROOT CLASSIC CLUB DANCE EUROPE FOREIGN GROUP FOREIGN ROCK

NAVIGATION > ORIGINAL

001.

IT’S SHOWTIME!!/B’z

002.

ONLY FLOWER IN THE WORLD/SMAP

003.

SEXY GUY/GOMAKI

004.

HEY?/AYAYA

005.

DOOR TO TOMORROW/I WISH

REASON/ASAMI

006.

007.

DIE ANOTHER DAY/JAMES BOND

IT’S SHOWTIME!!/B’z

001.

ONLY FLOWER IN THE WORLD/SMAP

002.

SEXY GUY/GOMAKI

003.

HEY?/AYAYA

004.

DOOR TO TOMORROW/I WISH

005.

REASON/ASAMI

006.

007.

DIE ANOTHER DAY/JAMES BOND

0:07:01

NOTES:

● If there are more than 100 files, the rest of the files are not

displayed. In this case, press ON SCREEN to display them on the TV screen.

● If both MP3 files and WMA files are recorded on the same disc,

WMA files cannot be played back as they are not displayed on the navigation screen.

56 EN

EDITING

Dubbing

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

DVDTV

HDD

UBBING

ENTER

R o

NOTES:

● It is not possible to dub copy-protected contents. An error

message will appear on the TV screen.

● It is not possible to dub simultaneously when timer

programming is set. Select either dubbing or timer programming.

● The order of the index which are displayed by pressing

DUBBING differs from the images displayed by pressing NAVIGATION or EDIT.

DVD

MARK

FGDE

ON SCREEN

5 Press FGD E to select indexes (small pictures) of desired

original recordings and/or play lists, then press MARK. After selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

● The recordable time of the disc is displayed on the bar meter.

For details, refer to AAbout Disc Remaining DisplayB (A pg. 58).

6 Press DE to select A EXECUTEB, then press ENTER to start

dubbing.

NOTES:

● Play lists are dubbed as programmes.

● In Video mode, if the selected play list includes the scenes

recorded in the different transfer rate, the dubbing is performed in the highest transfer rate of the scenes in the selected play list.

● During dubbing, it is not possible to play back on HDD or DVD, or

to set timer programming.

● It is not possible to discontinue dubbing once it has been started.

Just Dubbing (From HDD To DVD)

By using Just Dubbing function, when dubbing all selected original recordings and/or play lists, the unit automatically sets the appropriate recording mode depending on the combination of the total time of the selected recordings and/or play lists to be dubbed and the available disc space.

1 Load a recordable disc. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select AHDDNDV DB, then press ENTER. 4 Press FGD E to select AJUSTB, then press ENTER. 5

Perform steps5–6 of AHigh Speed Dubbing (From HDD To DVD)B.

NOTES:

● Play lists are dubbed as programmes.

● In Video mode, if the selected play list includes the scenes

recorded in the different transfer rate, the dubbing is performed in the highest transfer rate of the scenes in the selected play list. However, the lower transfer rate cannot be dubbed in the higher transfer rate.

● The recordable time of the disc is displayed on the bar meter. For

details, refer to AAbout Disc Remaining DisplayB (A pg. 58).

● During dubbing, it is not possible to play back on HDD or DVD, or

to set timer programming.

● It is not possible to discontinue dubbing once it has been started.

High Speed Dubbing (From HDD To DVD)

It is possible to dub the original recordings and/or play lists on the HDD deck to DVD discs. The dubbing is performed in high speed, keeping the original transfer rate.

NOTES:

● After accessing the Dubbing Menu screen, it is not possible to

take out a disc.

● It is not possible to dub copy-once titles in Video mode.

● When dubbing a copy-once title, the data will be moved from

HDD to DVD upon completing dubbing.

● When you cancel dubbing a copy-once title during dubbing, the

original recording on the HDD deck remains and the title copied to a DVD disc is deleted.

● It is not possible to dub play lists which contain copy-once titles.

● It is not possible to dub the following programmes to DVD-R/RW

disc (Video mode):

● which contains more than one audio language.

● which is on the play list.

● which is edited (also RetroActive Recording).

● which is recorded in LP mode or FP155-FP240 mode.

Recording may not be performed in the highest speed depending

●

on the characteristics of the disc used.

1 Load a recordable disc. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select AHDDNDV DB, then press ENTER. 4 Press FGD E to select AHIGH SPEEDB, then press ENTER.

Manual Dubbing (From HDD To DVD)

It is possible to perform dubbing in the desired transfer rate.

1 Load a recordable disc. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select AHDDNDV DB, then press ENTER. 4 Press FGD E to select AMANUALB, then press ENTER. 5 Perform step 5 of AHigh Speed Dubbing (From HDD To DVD)B.

The Manual Dubbing screen appears.

6 Press FG to select AREC MODEB, then press ENTER. Press

FG to select the desired option, then press ENTER.

7 Press G to select ACONFIRMB, then press ENTER. 8 Press DE to select A EXECUTEB, then press ENTER to start

dubbing.

NOTES:

● In Video mode, if the selected play list includes the scenes

● The recordable time of the disc is displayed on the bar meter. For

details, refer to AAbout Disc Remaining DisplayB (A pg. 58).

● During dubbing, it is not possible to play back on HDD or DVD, or

to set timer programming.

● It is not possible to discontinue dubbing once it has been started.

EDITING

EN 57

Dubbing From HDD To DV

It is possible to perform dubbing from the HDD deck to the DV deck.

1 Load a Mini DV cassette with the erase protection switch set to

ARECB.

2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select AHDDNDV B, then press ENTER. 4 Press FGD E to select indexes (small pictures) of desired

original recordings and/or play lists, then press MARK. After

selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

5 Press FG to select ASELECT REC. MODEB, then press

ENTER. Press FG to select the desired option, then press

ENTER.

6 Press FG to select ASELECT SND. MODEB, then press

ENTER. Press FG to select the desired option, then press

ENTER.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

8 Press DV so that the DV lamp lights up on the unit. 9 Press I to locate the point from where you want to start

dubbing, then press R and W simultaneously so that the DV

deck enters the record pause mode.

10 Press HDD so that the HDD lamp lights up on the unit.

● The dubbing screen will appear.

11 Press DE to select AEXECUTEB, then press ENTER for

confirmation.

● To cancel the dubbing, press o then DE to select ACANCELB

and press ENTER to confirm.

12 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to end.

Original Dubbing (From DVD To HDD)

It is possible to dub the original recordings on DVD discs to the HDD deck.

1 Load a disc you want to dub. 2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select ADV DNHDDB, then press ENTER. 4 Press FGD E to select indexes (small pictures) of desired

original recordings and/or play lists, then press MARK. After

selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

5 Press DE to select AEXECUTEB, then press ENTER to start

dubbing.

NOTES:

● It is not possible to dub play lists on DVD discs.

● It is not possible to dub pre-recorded DVDVIDEO discs.

● It is not possible to dub Video CDs/SVCDs or Audio CDs.

● It is not possible to discontinue dubbing once it has been started.

Dubbing From DVD To DV

It is possible to perform dubbing from the DVD deck to the DV deck.

1 Load the disc you want to dub onto the DVD deck, and a Mini

DV cassette with the erase protection switch set to ARECB to the DV deck.

2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select ADV DNDVB, then press ENTER. 4 Press FGD E to select indexes (small pictures) of desired

original recordings and/or play lists, then press MARK. After selecting all indexes you want to dub, press ENTER.

● You can select up to 8 original recordings and/or play lists.

5 Press FG to select ASELECT REC. MODEB, then press

ENTER. Press FG to select the desired option, then press ENTER. The confirmation screen appears.

6 Press FG to select ASELECT SND. MODEB, then press

ENTER. Press FG to select the desired option, then press ENTER.

● Sound mode selection is not available when dubbing a

DVD-RW (Video mode) or DVD-R disc.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

8 Press DV so that the DV lamp lights up on the unit. 9 Press I to locate the point from where you want to start

dubbing, then press R and W simultaneously so that the DV deck enters the record pause mode.

10 Press DVD so that the DVD lamp lights up on the unit.

● The dubbing screen will appear.

11 Press DE to select AEXECUTEB, then press ENTER to

confirm.

● To cancel the dubbing, press o then DE to select ACANCELB

and press ENTER to confirm.

12 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to end.

NOTES:

● It is not possible to dub play lists on DVD discs.

● It is not possible to dub Video CDs/SVCDs or Audio CDs.

● When dubbing is in progress, only o is functional.

58 EN

EDITING

Dubbing From DV To HDD (Dubbing An Entire Cassette)

It is possible to perform automatic dubbing of all the recorded programmes of a cassette from the DV deck to the HDD deck using the AENTIREB dubbing.

1 Load the Mini DV cassette you want to dub. Make sure its erase

protection switch is set to ASAVEB.

● Set ADV AUDIO RECB to the appropriate mode. (A pg. 72)

2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select ADV NHDDB, then press ENTER. 4 Select AENTIREB, then press ENTER. 5 Press FG to select ASELECT REC. MODEB, then press

ENTER. Press FG to select the desired option, then press

ENTER.

6 Press FG to select ASELECT SND. MODEB, then press

ENTER. Press FG to select the desired option, then press

ENTER.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

8 Press DE to select AEXECUTEB, then press ENTER for

confirmation.

● Once dubbing starts, it will continue dubbing until the end of the

tape is reached.

● To cancel the dubbing, press o then DE to select ACANCELB

and press ENTER to confirm.

● If the tape is not rewind, the unit will start dubbing after

automatically rewinding the tape to the beginning.

9 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to

end.

● The tape will automatically be rewound.

NOTES:

● ASUPERIMPOSEB is automatically set to AOFFB. It will return to

AAUTOB after dubbing is completed.

● When there are blanks on the tape of more than 2 seconds, the

HDD deck will enter into pause mode. Dubbing will resume once recorded portion is detected.

● Dubbing copyright guarded tape is not possible.

● When dubbing is in progress, only o is functional.

9 Upon completing dubbing, the tape stops and ADUBBING

COMPLETEDB appears on the TV screen. Press ENTER to end.

● The tape will automatically be rewound.

NOTES:

● ASUPERIMPOSEB is automatically set to AOFFB. It will return to

AAUTOB after dubbing is completed.

● The programme information at the DV deck will not be dubbed.

● When there are blanks on the tape of more than 2 seconds, the

DVD deck will enter into pause mode. Dubbing will resume once recorded portion is detected.

● Dubbing copyright guarded tape is not possible.

● When dubbing is in progress, only o is functional.

About Disc Remaining Display

When dubbing from HDD to DVD, the unit displays the time information for dubbing by bar meter. By comparing the disc remaining time and the necessary time for dubbing of the selected items, it is possible to check if the dubbing can be performed completely or not.

When performing the High Speed Dubbing

Capacity of a disc Remaining capacity

21%

Dark green: Length of already recorded item Light green: Length of selected item Yellow: Length of the item now being selected by arrow Red: Excess over the capacity

When performing the Just Dubbing

TOTAL 105MIN

● The unit displays the status on the assumption that the selected

items are dubbed in the lowest transfer rate.

● The total time of a loaded disc is displayed on the right of the bar

meter.

When performing the Manual Dubbing

Dubbing From DV To DVD (Dubbing An Entire Cassette)

It is possible to perform automatic dubbing of all the recorded programmes of a cassette from the DV deck to the DVD deck using the AENTIREB dubbing.

1 Load the Mini DV cassette you want to dub. Make sure its erase

protection switch is set to ASAVEB.

● Set ADV AUDIO RECB to the appropriate mode. (A pg. 72)

2 Press DUBBING to access the Dubbing Menu screen. 3 Press FGD E to select ADV NDVDB, then press ENTER. 4 Select AENTIREB, then press ENTER. 5 Press FG to select ASELECT REC. MODEB, then press

ENTER. Press FG to select the desired option, then press

ENTER.

6 Press FG to select ASELECT SND. MODEB, then press

ENTER. Press FG to select the desired option, then press

ENTER.

7 Press G to select ACONFIRMB, then press ENTER. The

confirmation screen appears.

8 Press DE to select AEXECUTEB, then press ENTER for

confirmation.

● Once dubbing starts, it will continue dubbing until the end of the

tape is reached.

● To cancel the dubbing, press o then DE to select ACANCELB

and press ENTER to confirm.

● If the tape is not rewind, the unit will start dubbing after

automatically rewinding the tape to the beginning.

MAX FR240

● The unit displays the status on the assumption that the selected

items are dubbed in the lowest transfer rate.

● The available highest transfer rate is displayed on the right of the

bar meter.

DV Dubbing (HDD & DVD Deck Only)

L–R

SOUND1

0:00 1:00 2:00

GR-DV3500

GR-DV3500DV

HDD

00:00: 00.00

12bit

JVC

00:00: 00.00

FR360

DV DV

1 2

A B C

You can dub programmes from a camcorder or DV equipment connected to the unit with a DV cable. The unit’s remote control allows you the limited control of the connected camcorder or DV equipment functions during dubbing.

NOTES:

● Use the DV cable VC-VDV 204U for connection.

● When you connect a PC to the [DV IN] connector, we do not

assure the normal operation of this unit.

Your unit

To [DV IN]

Camcorder

DV equipment

DV cable

(VC-VDV 204U)

(not supplied)

DV connector

EDITING

EN 59

The following on-screen display for DV dubbing appears when ON SCREEN is pressed while the channel has been set to ADVB.

A Remote control switch

To switch between the devices operable by the remote control unit. The unit is operable when the remote icon ( ) displayed faces to the left, while the DV device is operable when the remote icon is facing to the right.

B Auto capture button

Select to start or pause the dubbing. If ENTER is pressed when the DV device is in the pause condition, preroll editing* where it is possible to dub with a start time that is highly accurate will be activated. When the DV device cannot be operated from the unit (such as in camera mode), proceed with normal recording (A pg. 32, 35).

* Preroll editing refers to the playback after the DV tape is slightly

rewind. (For DV devices that do not support the –1x speed, the rewinding time may be longer.)

C Sound monitor switch

For selecting the desired sound format for dubbing.

1 Connect a camcorder or DV equipment to the [DV IN]

connector on the unit’s front panel.

2 Press DV/HDD/DVD on the unit repeatedly or HDD on the

remote so that the HDD lamp lights up on the unit.

3 Press PR +/– or INPUT SELECTJK to set the channel to ADVB. 4 Press ON SCREEN.

● The on-screen display for DV dubbing appears.

5 Press DE to select , then press ENTER to display

the remote icon (facing to the right) for the DV equipment.

6 Press REC MODE repeatedly to set the recording mode. 7 Locate the point from where you want to start dubbing, then

stop or pause playback by pressing the following buttons on the remote control: I, N, O, o, W.

● To play back in slow speed (1/10 of the normal speed), press W

to pause playback, then press O or N.

● To play back frame-by-frame, press W to pause playback, then

press W repeatedly. Each press of W advances a frame.

● To change the playback direction, press O or N.

8 Press DE to select , then press ENTER repeatedly

until the desired sound track appears on the TV screen.

SOUND1:

Select this to record the original stereo sound played back on the connected DV equipment.

SOUND2:

Select this to record the dubbed stereo sound played back on the connected DV equipment.

MIX:

Select this to record the sound of both ASOUND1B and ASOUND2B.

● Note that this selection is not available when the source

programme is recorded in 16BIT (48 kHz) mode.

9 Press DE to select , then press ENTER. The

dubbing starts.

● Playback on the external DV equipment and recording on the

unit should start simultaneously.

● To pause dubbing, press DE to select , then press

ENTER. Both the unit and the external DV equipment pause dubbing. Pressing W on the unit also works the same way.

10 Press DE to select , then press ENTER. Then

press o. The DV equipment stops.

11 Press DE to select , then press ENTER.

60 EN

EDITING

12 Press o twice on the remote control to stop dubbing.

● Both the unit and the external DV equipment stop dubbing.

NOTES:

● Dubbing copyright guarded programmes is not possible.

● Original DV information such as the recording date and time are

not recorded.

● The superimposed indication during the operation or dubbing is

not recorded.

● If the dubbing is paused while the channel is set to ADVB, you

cannot switch channels.

When you dub from DV equipment other than a camcorder

A Perform step 1 to 4. B Locate the point from where you want to start dubbing,

then stop on the DV equipment.

● If you pause the DV equipment in this step, a few

second’s still picture will be recorded at the beginning of the recorded programme.

Set the input mode to ADV I NPUTB on the DV equipment.

● If you select an input mode other than ADV INPUTB,

unwanted pictures may be recorded at the beginning of the recorded programme.

D Perform step 9 to 12.

To skip unwanted part of the source picture

Press ENTER to stop both equipment, then press DE to select

Locate the point where you want to restart dubbing by pressing I, N, or O, then press o. Press DE to select , then press ENTER to restart dubbing.

Edit From A Camcorder

You can use a camcorder as the source player and your unit as the recording deck. If your camcorder has a DV IN/OUT connector, you can use the camcorder as the recording deck and your unit as the source player.

A If the camcorder has no S-VIDEO output connector:

To [VIDEO/AUDIO ((MONO) L/R)] input

Audio/video cable (not supplied)

AUDIO/VIDEO OUT

Player

B If the camcorder has an S-VIDEO output connector:

To [S-VIDEO]

input

S-video cable (not supplied)

To [AUDIO] input

S-VIDEO OUT

Recorder

Audio cable (not supplied)

●

Slide the TV/CABLE/SAT/DVD switch to DVD.

EDITING

EN 61

1 Make connections.

A If the camcorder has no S-VIDEO output connector:

^ connect the camcorder’s AUDIO/VIDEO OUT connectors to

the unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front panel.

● When using a monaural camcorder, connect its AUDIO OUT

connector to the [AUDIO-L] input connector on your unit.

B If the camcorder has an S-VIDEO output connector:

^ connect the camcorder’s AUDIO OUT and S-VIDEO OUT

connectors to the unit’s [AUDIO] and [S-VIDEO] input connectors on the front panel.

C If the camcorder has a DV IN/OUT connector:

^ connect the camcorder’s DV IN/OUT connector to the unit’s

[DV IN/OUT] connector.

● When using your unit as the source player, refer to the

camcorder’s instruction manual for the recording procedure.

2 Press DV/HDD/DVD on the unit repeatedly to select the

recording deck.

3 Press PR +/– or INPUT SELECTJK to select AF-1B or ADVB.

● Set AF-1 INPUTB to AVIDEOB for the [AUDIO] input connector, or

AS-VIDEOB for the [S-VIDEO] input connector, depending on

the connector being used. (A pg. 64)

4 Press REC MODE repeatedly to set the recording mode. 5 Start playback on the camcorder slightly before the actual point

from where you wish to start dubbing.

6 Press R on the unit to start recording. Or while holding R, press

I on the remote control. The dubbing starts.

7 Press o on the unit, then stop playback on the camcorder.

NOTES:

● All necessary cables can be obtained from your dealer.

● Refer to the camcorder’s instruction manual for operating

procedure.

● The quality of dubbed picture becomes poorer than that of the

original.

● When you are editing through the [DV IN/OUT] connector, the

unit will stop if the player begins playing a blank portion of tape or the signal is interrupted.

● When connecting the unit to a device equipped with a DV input

connector, be sure to use the optional DV cable (VC-VDV204U)

● To edit through the [DV IN/OUT] connector using the HDD or

DVD deck, refer to ADV Dubbing (HDD & DVD Deck Only)B (A pg. 59).

AUDIO OUT

Player

C If the camcorder has a DV IN/OUT connector:

Recorder/Player

Player/Recorder

To [DV IN]

(VC-VDV 204VU)

(not supplied)

DV connector

DV cable

62 EN

EDITING

Edit To Or From Another Recorder

You can use your unit as the source player or as the recording deck.

NOTES:

● When using another recorder as the recording deck, refer to its

instruction manual.

● It is not possible to dub copy-protected contents. An error

message will appear on the TV screen.

A When using your unit as the source player

TV receiver

21-pin SCART cable

B When using your unit as the recording deck

Player

(not supplied)

Recorder

21-pin SCART cable

Another recorder

Your unit

(supplied)

●

Slide the TV/CABLE/SAT/DVD switch to DVD.

1 Connect another recorder’s 21-pin SCART connector to the

unit’s 21-pin SCART connector as illustrated.

A When using your unit as the source player:

^ connect its [L-1 IN/OUT] connector to the recording deck.

B When using your unit as the recording deck:

^ connect its [L-2 IN/DECODER] connector to the source

player.

● If another recorder is compatible with the Y/C signal:

^ when using your unit as the source player, set AL-1

OUTPUTB to ASCART S-VIDEOB. (A pg. 63)

^ when using your unit as the recording deck, set AL-2

SELECTB to AS-VIDEOB. (A pg. 63)

2 When using this unit as the recording deck, press DV/HDD/

DVD on the unit repeatedly to select the recording deck.

3 When using this unit as the recording deck, press PR +/– or

INPUT SELECTJK to select AL-2B.

● Set AL-2 SELECTB to AVIDEOB or AS-VIDEOB. (A pg. 63)

4 When using this unit as the recording deck, press REC MODE

repeatedly to set the recording mode.

5 Engage the Play mode of the source player. 6 Engage the Record mode of the recording deck. 7 Stop recording on the recording deck, then stop playback on

the source player.

NOTES:

● All necessary cables can be obtained from your dealer.

● For Y/C signal input/output, be sure to use a 21-pin SCART cable

that is compatible with the Y/C signal.

● When you use this unit as the source player for editing, be sure to

set ASUPERIMPOSEB to AOFFB before starting. (A pg. 73) If you are using another recorder with S-Video and Audio output connectors, connect its S-Video and Audio output connectors to this unit’s [S-VIDEO] and [AUDIO] input connectors on the front panel. Then, set the unit’s input mode to AF-1B in step 3, and set AF-1 INPUTB to AS-VIDEOB. (A pg. 64)

TV receiver

21-pin SCART cable

(not supplied)

Recorder

Player

Another recorder

Your unit

21-pin SCART

cable (supplied)

Output/Input Set

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

ENTER

FGDE

SET UP

EDITING

EN 63

SCART RGB:

If a connected appliance’s input is compatible with RGB signals, set to ASCART RGBB. You can obtain a high-quality RGB picture.

COMPONENT:

If a connected appliance’s input is compatible with Y/PB/PR signals, set to ACOMPONENTB. You can obtain a high-quality Y/P

picture. Switch the TV to the input that you can watch

DVDTV

B/PR

component video pictures.

8 L-1 INPUT ^ VIDEO / S-VIDEO

VIDEO:

If a connected appliance’s output is compatible only with regular video signals, set to AVIDEOB.

S-VIDEO:

If a connected appliance’s output is compatible with Y/C signals, set to AS-VIDEOB. You can obtain a high-quality picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

NOTES:

● If AL-1 OUTPUTB is set to ASCART S-VIDEOB or ASCART RGBB, it

is not possible to set AL-1 INPUTB to AS-VIDEOB.

● If AL-2 SELECTB is set to ASAT S-VIDEOB or ADECODERB, it is

not possible to set AL-1 INPUTB to AS-VIDEOB.

● If AL-2 SELECTB is set to ADECODERB, it is only possible to set

AL-1 OUTPUTB to ASCART VIDEOB

● Component video signals are not output from the [L-1 IN/OUT]

connector.

● When Progressive scan mode is engaged, it is not possible to

select the setting of AL-1 OUTPUTB. (A pg. 63)

L-1 Output And L-1 Input Setting

The [L-1 IN/OUT] connector accepts and delivers either a composite signal (regular video signal) or a Y/C signal (a signal in which the luminance and chrominance signals are separated). Set AL-1 OUTPUTB and AL-1 INPUTB to the appropriate mode depending on the type of appliance connected to the unit’s [L-1 IN/ OUT] connector.

1 Press SET UP to access the Main Menu screen. 2 Press DE to select AFUNCTION SET UPB, then press G. 3 Press DE to select AVIDEO

IN/OUTB, then press G.

4 Press FG to select AL-1

OUTPUTB or AL-1 INPUTB,

then press ENTER.

5 Press FG to select the

appropriate setting, then press

ENTER.

6 Press SET UP to complete the

setting.

*The boldface settings below indicate the settings at your purchase.

8 L-1 OUTPUT ^ SCART VIDEO / SCART S-VIDEO / SCART

RGB / COMPONENT

SCART VIDEO:

If a connected appliance’s input is compatible only with regular

video signals, set to ASCART VIDEOB

SCART S-VIDEO:

If a connected appliance’s input is compatible with Y/C signals,

set to ASCART S-VIDEOB. You can obtain high-quality picture.

(For connection, be sure to use a 21-pin SCART cable that is

compatible with the Y/C signal.)

DVD VIDEO SET UP

HDD/DVD/DV SET UP

REC/PLAY SET UP DISPLAY SET

MONITOR TYPE

F-1 INPUT

L-1 OUTPUT

L-1 INPUT

L-2 SELECT

SELECT WITH @ THEN PRESS [ENTER]

ENTER

SET UP

EXIT

DVD VIDEO SET UP

REC/PLAY SET UP DISPLAY SET

SET UP

EXIT

MONITOR TYPE

F-1 INPUT

L-1 OUTPUT

L-1 INPUT

L-2 SELECT

SELECT

HDD/DVD/DV SET UP

ENTER

SELECT

PRESS [SET UP] TO EXIT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

FUNCTION SET UP

VIDEO IN/OUT

FUNCTION SET UP

VIDEO IN/OUT

4:3LB

VIDEO

SCART VIDEO

VIDEO

4:3LB

VIDEO

SCART VIDEO

SCART S-VIDEO

VIDEO SCART RGB

COMPONENT

VIDEO

INITIAL SET UP

L-2 Select Setting

Set AL-2 SELECTB to the appropriate mode depending on the type of appliance connected to the unit’s [L-2 IN/DECODER] connector.

1 Perform steps 1 and 2 of AL-1 Output And L-1 Input SettingB on

the left column.

2 Press FG to select AL-2 SELECTB, then press ENTER. 3 Press FG to select the

appropriate setting, then press ENTER.

4 Press SET UP to complete the

setting.

*The boldface settings below indicate the settings at your purchase.

8 L-2 SELECT ^ VIDEO / S-VIDEO / SAT VIDEO / SAT S-VIDEO /

DECODER

Select AVIDEOB or AS-VIDEOB to use this unit as the recording deck with the player connected to the [L-2 IN/DECODER] connector, or to use the satellite receiver connected to the [L-2 IN/DECODER] connector.

VIDEO:

If a connected appliance’s output is compatible only with regular video signals, set to AVIDEOB.

S-VIDEO:

If a connected appliance’s output is compatible with Y/C signals, set to AS-VIDEOB. You can obtain high-quality picture. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

Select ASAT VIDEOB or ASAT S-VIDEOB to view a satellite programme with the TV set while the unit is turned off. (A pg. 69)

SAT VIDEO:

If a connected satellite receiver’s output is compatible only with regular video signals, set to ASAT VIDEOB.

SAT S-VIDEO:

If a connected satellite receiver’s output is compatible with Y/C signals, set to ASAT S-VIDEOB. (For connection, be sure to use a 21-pin SCART cable that is compatible with the Y/C signal.)

DVD VIDEO SET UP

HDD/DVD/DV SET UP

REC/PLAY SET UP DISPLAY SET

MONITOR TYPE

F-1 INPUT

L-1 OUTPUT

L-1 INPUT

L-2 SELECT

ENTER

EXIT

SELECT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

SET UP

FUNCTION SET UP

VIDEO IN/OUT

4:3LB

VIDEO

SCART VIDEO

VIDEO

INITIAL SET UP

VIDEO

S-VIDEO SAT VIDEO DECODER

64 EN

EDITING

DECODER:

To use a decoder connected to the [L-2 IN/DECODER] connector.

NOTES:

● If you have a satellite receiver or a decoder connected to the [L-2

IN/DECODER] connector, be sure to set AL-2 SELECTB back to appropriate mode after editing.

● If you are not connecting a satellite receiver or a decoder to the

[L-2 IN/DECODER] connector, leave AL-2 SELECTB set to AVIDEOB.

● When AL-2 SELECTB is set to ASAT VIDEOB and ASAT S-VIDEOB,

ASATB appears on the TV screen or front display panel instead of AL-2B.

● If AL-1 OUTPUTB is set to ASCART S-VIDEOB, it is not possible to

set AL-2 SELECTB to ADECODERB or ASAT VIDEOB.

● If AL-1 OUTPUTB is set to ASCART RGBB, it is not possible to set

AL-2 SELECTB to ADECODERB or ASAT S-VIDEOB.

● If AL-1 OUTPUTB is set to ACOMPONENTB and AL-2 SELECTB to

ASAT VIDEOB, ASAT S-VIDEOB or ADECODERB, be sure to

connect the [L-1 IN/OUT] connector with a TV.

● If AL-2 SELECTB is set to ASAT S-VIDEOB , be sure to set AL-1

OUTPUTB to ASCART S-VIDEOB.

● The BNC and S-Video output do not support the satellite receiver

function. Make use of the L-1 output when viewing images from the satellite receiver.

F-1 Input Setting

Set AF-1 INPUTB to the appropriate mode depending on the connector (VIDEO or S-VIDEO) being used on the front panel.

1 Perform steps 1 and 2 of AL-1 Output And L-1 Input SettingB

(A pg. 63).

2 Press FG to select AF-1 INPUTB, then press ENTER. 3 Press FG to select the

appropriate setting, then press ENTER.

4 Press SET UP to complete the

setting.

*The boldface settings below indicate the settings at your purchase.

DVD VIDEO SET UP

HDD/DVD/DV SET UP

REC/PLAY SET UP DISPLAY SET

MONITOR TYPE

F-1 INPUT

L-1 OUTPUT

L-1 INPUT

L-2 SELECT

SELECT WITH @ THEN PRESS [ENTER]

ENTER

SET UP

EXIT

SELECT

PRESS [SET UP] TO EXIT

FUNCTION SET UP

VIDEO IN/OUT

4:3LB

VIDEO

SCART VIDEO

VIDEO

INITIAL SET UP

VIDEO

S-VIDEO

Digital Audio Dubbing

You can dub selected audio from a DVD or Audio CD disc to a digital audio device. However, it is not possible to dub copy-protected discs.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

Example: Dubbing to an MD

Recorder

Digital audio device

(MD deck, etc.)

Optical cable (not supplied)

To [DIGITAL AUDIO OUT (OPTICAL)]

Rear of unit

Player

Coaxial cable

(not supplied)

To [DIGITAL AUDIO OUT

(COAXIAL)]

Note for connection:

Remove the protection cap from the optical cable.

8 F-1 INPUT ^ VIDEO / S-VIDEO

VIDEO:

When connecting an appliance to the [VIDEO] input connector, set to AVIDEOB.

S-VIDEO:

When connecting an appliance to the [S-VIDEO] input connector, set to AS-VIDEOB

1 Connect the unit and a digital audio device using either an

optional optical cable or an optional coaxial cable.

2 Place a disc on the unit and load an MD on the connected

digital audio device.

3 Select the audio to be dubbed. 4 Start playback slightly before the actual point from where you

wish to start dubbing.

5 Press W to pause playback. 6 Select the input mode on the connected digital audio device. 7 Press I to start playback on the unit. 8 Start recording on the digital audio device. 9 Stop recording on the digital audio device. Then press o to stop

playback on the unit.

NOTE:

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.

Audio Dubbing (DV Deck Only)

This function allows you to record new audio, without erasing the original audio, on a DV tape that was recorded with ADV AUDIO RECB set to A12BITB (A pg. 72).

ATTENTION:

You cannot perform Audio Dubbing on a tape that was recorded with ADV AUDIO RECB set to A16BITB (A pg. 72), on a tape that was recorded at the ALPB speed, or on a blank tape.

Your unit

To [AUDIO]

input

Your unit

INPUT SELECTJK

Audio cable (not supplied)

AUDIO OUT

CD player, etc.

Mixer output

Original sound

[AUDIO OUT]

Recorder

AUDIO DUB.

Audio mixer

Recorder

●

Slide the TV/CABLE/SAT/DVD switch to DVD.

EDITING

EN 65

1 Connect an audio device to the unit’s [AUDIO] input connectors

on the front panel.

● When using a monaural audio device, connect its AUDIO OUT

connector to the [AUDIO-L] input connector on your unit.

2 Load a Mini DV cassette with the erase protection switch set to

ARECB.

3 Press DV/HDD/DVD on the unit repeatedly or DV on the remote

so that the DV lamp lights up on the unit.

4 Press PR +/– on the remote control or INPUT SELECTJK on

the unit to select AF-1B.

5 Start playback slightly before the actual point from where you

wish to start dubbing.

6 Press W to pause playback. 7 Press AUDIO DUB. to engage the audio dubbing mode.

● Your unit enters the Audio Dubbing Pause mode.

● To perform Audio Dubbing with audio mixing, press AUDIO to

select AL W X RB at this point. When using the DV deck as the recording deck, also make sure that AAUDIO MODEB is set to ASOUND1B (A pg. 72).

* Audio Dubbing with audio mixing is not possible if you are using a

monaural audio component, or if you don’t have an audio mixer.

8 Engage the audio device’s playback, then press I to start the

tape in the unit. Audio dubbing starts at this point.

● To stop dubbing temporarily, press W. Press I to resume

dubbing.

9 Press o on the unit, then stop playback on the audio device to

end the audio dubbing.

NOTES:

● Once the Audio Dubbing starts, you cannot use the other deck.

● When monitoring the audio dubbed sound on the DV deck, set

AAUDIO MODEB to ASOUND2B (A pg. 72).

● Audio Dubbing is also possible with the [L-1 IN/OUT] or [L-2 IN/

DECODER] connector on the rear panel. When using these 21pin SCART connectors, be sure to select the correct input mode (AL-1B or AL-2B) in step 4.

● When playing back an audio dubbed Mini DV tape on the DV

deck, set AAUDIO MODEB to ASOUND2B (A pg. 72).

● Audio dubbing is not possible using the [DV IN/OUT] connector.

● Audio dubbing is not possible on a blank portion of the tape.

[AUDIO]

input

INPUT SELECT

AUDIO DUB.

66 EN

EDITING

Insert Editing (DV Deck Only)

Insert Editing replaces the pictures with new ones, while the audio soundtrack remains unchanged. For Insert Editing, use your unit as the recording deck.

ATTENTION:

Insert Editing is not possible with a Mini DV cassette recorded in LP mode.

A If the player has no S-VIDEO output connector:

Your unit

Player

INPUT SELECT

To [VIDEO/AUDIO ((MONO) L/R)] input

Audio/video cable (not supplied)

AUDIO/VIDEO OUT

Another recorder

B If the player has an S-VIDEO output connector:

Your unit

To [S-VIDEO]

input

INPUT SELECTJK

To [AUDIO] input

Recorder

INSERT

Recorder

INSERT

●

Slide the TV/CABLE/SAT/DVD switch to DVD.

1 Make connections.

A If the player has no S-VIDEO output connector:

^ connect the player’s AUDIO/VIDEO OUT connectors to your

unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on the front panel.

B If the player has an S-VIDEO output connector:

^ connect the player’s AUDIO OUT and S-VIDEO OUT

connectors to your unit’s [AUDIO] and [S-VIDEO] input connectors on the front panel.

2 Load a Mini DV cassette with the erase protection switch set to

ARECB.

3 Press DV/HDD/DVD on the unit repeatedly or DV on the remote

so that the DV lamp lights up on the unit.

4 Press PR +/– on the remote control or INPUT SELECTJK on

the unit to select AF-1B.

5 Press S, T and W to determine the edit-in point (the

beginning of the segment to be replaced).

● Be sure to engage the Still mode at the edit-in point.

6 Press INSERT to engage the insert editing mode.

● Your unit enters the Insert Pause mode.

● The TV screen changes from the still picture to the input source

you are going to record.

7 Load the source cassette and play back the segment that is to

be inserted. When you reach the start of the section of the source tape that you wish to insert, press I to start the tape in your unit. Insert editing begins at this point.

8 Press o to stop recording on the DV deck to end insert editing.

NOTES:

● Once the Insert Editing starts, you cannot use the other deck.

● All necessary cables can be obtained from your dealer.

● Insert Editing cannot be performed on a Mini DV cassette that

has had its erase protection switch set to ASAVEB.

● When Insert Editing is performed on a tape that has been

recorded on another video recorder, the inserted portion may appear distorted.

● A small portion of the recording which precedes an insert edit

may become erased.

● Insert Editing is also possible with the [L-1 IN/OUT] or [L-2 IN/

DECODER] connector on the rear panel. When using these 21pin SCART connectors, be sure to select the correct input mode (AL-1B or AL-2B) in step 4.

● Insert Editing is not possible using the [DV IN/OUT] connector.

● Insert Editing is not possible on a blank portion of the tape.

S-video cable (not supplied)

S-VIDEO OUT

Player

Audio cable (not supplied)

AUDIO OUT

Another recorder

REMOTE CONTROL

EN 67

Remote Control Functions

Remote Control 1/2/3/4 Code Switching

The remote control is capable of controlling four JVC video units independently. Each of the units can respond to one of four codes (1, 2, 3 or 4). The remote control is preset to send 3 code signals because your unit is initially set to respond to 3 code signals. You can easily modify your unit to respond to 1, 2 or 4 code signals.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

1 – 4

ENTER

SET UP

● Keep pressing SET UP down during step 1.

1 Press the number key A1B for 1, A2B for 2, A3B for 3 or A4B for 4 to

change the remote control code, then press ENTER.

2 Press A on the unit to turn off the unit. 3 Press I on the unit for over 5 seconds while the unit is turned

off. The code currently set appears on the front display panel.

4 Press o on the remote control to change the unit’s code. The

code currently set on the remote control blinks on the front display panel for approximately 5 seconds, and is applied to the unit.

NOTE:

When APOWER SAVEB is set to AONB (A pg. 73), it is not possible to change the remote code.

CABLE/SAT

DVDTV

CABLE/SAT

TV AV /VIDEO

TV d

0 – 9

TV 8 +/–

PR +/–

ENTER

SET UP

DVDTV

TV Multi-Brand Remote Control

Your remote control can operate the basic functions of your TV set. In addition to JVC TVs, other manufacturer’s TVs can also be controlled.

● Turn off the TV using its remote control.

● Slide the TV/CABLE/SAT/DVD switch to TV.

IMPORTANT:

Although the provided remote control unit is compatible with JVC televisions, as well as many other models, it may not work with your TV, or in some instances, may have limited function capability.

● Keep pressing SET UP down during step 1.

1 Enter your TV’s brand code using the number keys, then press

ENTER.

2 Press A on the unit’s remote control to turn on the TV and try

operations (A step 3).

● Once you have set the remote control to operate the TV, you do

not have to repeat this step until you replace your remote control’s batteries.

● Some brands of TVs have more than one code. If the TV does

not function with one code, try entering another.

3 Press the corresponding buttons to operate the TV: A, TV AV/

VIDEO, PR +/–, TV8 +/–, TV d, number keys.

● For some brands of TVs, you must press ENTER after having

pressed the number keys.

68 EN

REMOTE CONTROL

BRAND NAME CODE

JVC FERGUSON FINLUX FUNAI LG/GOLDSTAR GRUNDIG HITACHI ITT MITSUBISHI MIVAR NEC NOKIA PANASONIC PHILIPS RCA SAMSUNG SANYO SHARP SONY THOMSON TOSHIBA

01, 23, 24, 25 27 30 32 18 19 10 28 03 29 20 31 04, 11 02 05 12, 33, 34, 35 13, 16 06 07 26 08, 14

Satellite Receiver Multi-Brand Remote Control

Your remote control can operate the basic functions of your satellite receiver set. In addition to JVC satellite receivers, other manufacturer’s satellite receivers can also be controlled.

BRAND NAME CODE

JVC AMSTRAD CANAL + D-BOX ECHOSTAR (VIA DIGITAL) FINLUX FORCE GALAXIS GRUNDIG HIRSCHMANN ITT NOKIA KATHREIN LUXOR MASCOM MASPRO NOKIA PACE PANASONIC PHILIPS RFT SAGEM SALORA SAMSUNG SKYMASTER TPS TRIAX WISI

72, 73 60, 61, 62, 63, 92 81 85 82 68 89 88 64, 65 64 68 70, 71 68 93 70 87 67, 86, 92 13, 14, 74 66, 84 69 83 68 05, 24 69 83 91 64

● Slide the TV/CABLE/SAT/DVD switch to CABLE/SAT.

IMPORTANT:

Although the provided remote control unit is compatible with JVC satellite receivers, as well as many other models, it may not work with your satellite receiver, or in some instances, may have limited function capability.

● Keep pressing SET UP down during step 1.

1 Enter your satellite receiver’s brand code using the number

keys, then press ENTER.

2 Press A on the unit’s remote control to turn on the satellite

receiver and try operations (A step 3).

● Once you have set the remote control to operate the satellite

receiver, you do not have to repeat this step until you replace your remote control’s batteries.

● Some brands of satellite receivers have more than one code. If

the satellite receiver does not function with one code, try entering another.

3 Press the corresponding buttons to operate the satellite

receiver: A, PR +/–, number keys.

● For some brands of satellite receivers, you must press ENTER

after having pressed the number keys.

● The number keys may not function with some satellite

receivers.

SYSTEM CONNECTIONS

EN 69

Connecting To A Satellite Receiver

Simple Connections

This is an example of a simple connection if your TV has one 21-pin AV input (SCART) connector.

Connect the satellite receiver to the [L-2 IN/DECODER] connector, then connect the [L-1 IN/OUT] connector to the TV’s connector.

NOTES:

● Set AL-2 SELECTB to AVIDEOB or AS-VIDEOB. (A pg. 63)

● You can use the Automatic Satellite Programme Recording

function (A pg. 48) with this connection. (HDD deck only)

● To record a programme via the satellite receiver, select L-2 mode

by pressing PR +/– or INPUT SELECTJK so that AL-2B appears on the front display panel.

● For details, refer to the instruction manual of the satellite

receiver.

Outdoor unit

Satellite cable

Satellite receiver

Aerial

TV aerial cable

ANTENNA IN

ANTENNA OUT

Perfect Connections (Recommended)

This is an example of recommended connections if your TV has two 21-pin AV input (SCART) connectors.

Connect the decoder to the satellite receiver’s connector if you have a decoder, [L-1 IN/OUT] connector to TV’s connector, and [L2 IN/DECODER] connector to the satellite receiver’s connector. Then connect the satellite receiver and TV.

NOTES:

● Set AL-2 SELECTB to AVIDEOB or AS-VIDEOB. (A pg. 63)

● You can use the Automatic Satellite Programme Recording

function (A pg. 48) with this connection. (HDD deck only)

● To record a programme via the satellite receiver, select L-2 mode

by pressing PR +/– or INPUT SELECTJK so that AL-2B appears on the front display panel.

● To receive a scrambled broadcast, descramble the signal with

the decoder connected to the satellite receiver.

● For details, refer to the instruction manual of the satellite receiver

and decoder.

Outdoor unit

Satellite cable

Satellite receiver

Aerial

TV aerial cable

ANTENNA IN ANTENNA OUT

IMPORTANT

When you set AL-2 SELECTB to ASAT VIDEOB or ASAT S-VIDEOB (A pg. 63), it is possible to view a satellite broadcast with the TV set to its AV mode even if the unit is turned off. When the unit is in Stop mode or recording, press TV AV/VIDEO on the remote control to turn off the VIDEO indicator on the front display panel.

● If you turn on the unit when the satellite receiver’s power is off,

nothing appears on the TV screen. In this case, turn on the satellite receiver, or set the TV to its TV mode, or press TV AV/

VIDEO on the remote control to set the unit to the AV mode.

Decoder

70 EN

SYSTEM CONNECTIONS

Connecting To A Dolby Digital Decoder Or An Amplifier With Built-in DTS

These instructions enable you to connect your unit to a Dolby Digital Decoder or an amplifier with built-in DTS.

Dolby Digital Decoder or

amplifier with built-in DTS

When you can’t switch the audio channel of a bilingual programme

When the unit is connected with a digital audio device using an optional optical cable and ADIGITAL AUDIO OUTB is set to ADOLBY DIGITAL/PCMB, it is not possible to switch the audio channel of a bilingual programme recorded on a DVD-RAM or DVD-RW (VR mode) disc. In this case, perform the following steps using the remote control to switch ADIGITAL AUDIO OUTB from ADOLBY DIGITAL/PCMB to APCM ONLYB.

A Press SET UP to access the Main Menu screen. B Press DE to select A DVD VIDEO SET UPB, then press G. C Press DE to select A AUDIO OUTPUTB, then press G. D Press FG to select ADIGITAL AUDIO OUTB, then press

ENTER.

E Press FG to select APCM ONLYB, then press ENTER.

(A pg. 71)

F Press SET UP to complete the setting. G Press AUDIO to select the desired audio channel.

To DIGITAL AUDIO input

Coaxial cable

(not supplied)

To [DIGITAL

AUDIO OUT

(COAXIAL)]

Note for connection:

Remove the protection cap from the optical cable.

Optical cable (not supplied)

To [DIGITAL AUDIO OUT (OPTICAL)]

Rear of unit

1 Connect the unit and a Dolby Digital Decoder or an amplifier

with built-in DTS using either an optional optical cable or an optional coaxial cable.

NOTES:

● For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBY

DIGITAL/PCMB. (A pg. 71)

● For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB.

(A pg. 71)

CAUTIONS:

● This unit has a dynamic range of more than 110 dB with regards

to its Hi-Fi audio capability. It is recommended that you check the maximum level if you are going to listen to the Hi-Fi audio signals through a stereo amplifier. A sudden surge in the input level to the speakers may damage them.

● Some speakers and televisions are specially shielded to prevent

television interference. If both are of the non-shielded type, do not place the speakers adjacent to the TV set as this can adversely affect the playback picture.

Connecting/Using A Decoder

The [L-2 IN/DECODER] connector can be used as an input connector for an external decoder (descrambler). Simply connect a decoder and you can enjoy a variety of programming that is available through scrambled channels.

Decoder

TV aerial cable

1 Set AL-2 SELECTB to ADECODERB. (A pg. 63) 2 Connect your unit’s [L-2 IN/DECODER] connector to the

decoder’s 21-pin SCART connector using a 21-pin SCART cable.

3 Perform the procedure as described in AWhen Receiving A

Scrambled Broadcast (HDD & DVD Deck Only)B (A pg. 76).

[L-1 IN/OUT]

RF cable (supplied)

[L-2 IN/

DECODER]

Mode Set

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

HDD

ENTER

DVD

FGDE

SUBSIDIARY SETTINGS

*The boldface settings below indicate the settings at your purchase.

EN 71

AUDIO OUTPUT

8 DIGITAL AUDIO OUT ^ DOLBY DIGITAL/PCM / STREAM/

/ PCM ONLY

PCM

Set to the appropriate mode according to the type of the device connected to [DIGITAL AUDIO OUT] connector.

DOLBY DIGITAL/PCM:

DVDTV

Select this when you connect the digital input connector of a Dolby Digital Decoder or an amplifier with a built-in Dolby Digital Decoder.

STREAM/PCM:

Select this when you connect the digital input connector of an amplifier with a built-in DTS, Dolby Digital, or MPEG multichannel decoder.

PCM ONLY:

Select this when you connect the linear PCM digital input of other audio equipment (amplifier, MD or DAT deck, etc.).

NOTES:

● This setting also functions when HDD is active.

● If you watch or play back a title which contains multiple audio

languages, select APCM ONLYB in advance and choose main or sub audio with AUDIO.

SET UP

AUDIO

Various modes of this unit are categorized into menus nested in 2 levels shown in the following table. To change the settings of these modes, find the desired mode in the menu (for details on each menu, see pages 71 through 73), then follow the procedure below.

DVD VIDEO SET UP LANGUAGE SET (A pg. 20)

AUDIO OUTPUT (A pg. 71) PARENTAL LOCK (A pg. 31) DISC PLAY SET UP (A pg. 72)

HDD/DVD/DV SET UP HDD SET UP (A pg. 72)

DVD SET UP (A pg. 72) DISC SET UP (A pg. 78, 79) DV SET UP ( A pg. 72)

FUNCTION SET UP REC/PLAY SET UP (A pg. 72)

DISPLAY SET (A pg. 73) VIDEO IN/OUT (A pg. 21, 63)

INITIAL SET UP TUNER SET (A pg. 74)

CLOCK SET (A pg. 77)

● The procedure below shows how to set the desired option of the

AAUDIO RECB mode as an example.

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press DE to select AFUNCTION SET UPB, then press G. 4 Press DE to select AREC/

PLAY SET UPB, then press G.

5 Press FG to select AAUDIO

RECB, then press ENTER.

6 Press FG to select the

desired option, then press ENTER.

7 Press SET UP to complete the

setting.

DVD VIDEO SET UP

HDD/DVD/DV SET UP

REC/PLAY SET UP DISPLAY SET

XP MODE REC AUDIO

AUDIO REC

DIRECT REC

INPUT COLOUR SYSTEM

JUMP TIME

ENTER

EXIT

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

SELECT

SET UP

FUNCTION SET UP

VIDEO IN/OUT

DOLBY DIGITAL

NICAM

OFF

PAL

15 MIN

INITIAL SET UP

8 ANALOG AUDIO OUT ^ STEREO / DOLBY SURROUND

Select the appropriate setting to accommodate the unit to the connected A/V equipment. This function takes effect when a DVD VIDEO disc is played back.

STEREO:

Select this when listening to conventional two-channel stereo audio with the unit’s [AUDIO OUT] connectors connected to a stereo amplifier/receiver or TV set, or in case you want to record the audio from a DVD VIDEO disc to a Mini Disc, etc.

DOLBY SURROUND:

Select this when listening to multichannel surround audio with the unit’s [AUDIO OUT] connectors connected to an amplifier/ receiver with a built-in surround decoder or a surround decoder.

8 D. RANGE CONTROL ^ NORMAL / WIDE RANGE / TV MODE

The dynamic range (the difference between the loudest sound and the quietest one) can be compressed during playback of a programme encoded in Dolby Digital format. This function takes effect when a DVD VIDEO disc recorded in Dolby Digital format is played back at low or middle volume.

NORMAL:

Normally select this setting to activate this function.

WIDE RANGE:

Select this to deactivate this function when you enjoy wide dynamic range programme.

TV MODE:

Select this when you hear the sound through the TV’s speaker(s).

NOTES:

● This function has no effect on programmes other than those

recorded in Dolby Digital format.

● This function does not work when Simulated Surround Effect is

activated. (A pg. 29)

● The effect of ANORMALB and AWIDE RANGEB may not be

different depending on discs.

8 OUTPUT LEVEL ^ STANDARD / LOW

You can lower the output level of analogue audio to accommodate the unit to the connected A/V equipment.

STANDARD:

Normally select this setting.

LOW:

The output level of analogue audio is lowered.

72 EN

SUBSIDIARY SETTINGS

DISC PLAY SET UP

8 RESUME ^ OFF / ON / DISC RESUME

When this function is set to AONB or ADISC RESUMEB, you can use the resume function. (A pg. 24)

OFF:

You cannot use the resume function.

ON:

You can start playback from the resume point of the placed disc.

DISC RESUME:

The unit retains a memory of the resume points of the last 30 discs played back, even though they have been ejected.

NOTE:

ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and already finalised DVD-R/DVD-RW (video mode) discs. For other types of discs, the function under AONB setting will be applied even if ARESUMEB is set to ADISC RESUMEB.

HDD SET UP

8 LIVE MEMORY ^ OFF / 30 MIN / 1 HR / 3 HR

When this function is set to A30 MINB, A1 HRB or A3 HRB, you can apply the selected time length to ATemporary recording for Live Memory (HDD deck only)B (A pg. 43).

DVD SET UP

8 SAVE AS LIBRARY ^ OFF / ON

When this function is set to AONB, the recording information is automatically stored in the library. For details, refer to AEdit Library InformationB (A pg. 54).

8 CONTINUOUS PLAY ^ OFF / ON

When this function is set to AONB, multiple titles on a disc are played back continuously one after another.

8 VIDEO MODE RECORDING ASPECT ^ PRIORITIZE 4:3 /

PRIORITIZE 16:9

This is the setting for the aspect ratio used when you dub titles to DVD discs in video mode. If the titles you want to dub are recorded in both 16:9 and 4:3, you must select one aspect ratio.

PRIORITIZE 4:3:

If you select APRIORITIZE 4:3B, even a title recorded in 16:9 is dubbed in 4:3.

PRIORITIZE 16:9:

If you select APRIORITIZE 16:9B, even a title recorded in 4:3 is dubbed in 16:9.

8 VIDEO MODE RECORDING AUDIO ^ MAIN / SUB

This is the setting for the audio channel to be selected when dubbing titles to DVD discs in video mode. Select either one of the two settings if the titles to be dubbed have two audio channels.

MAIN:

Select this to dub the main channel.

SUB:

Select this to dub the sub channel.

8 MP3 & WMA / JPEG ^ MP3 & WMA / JPEG

You can select files to play back, when both MP3&WMA files and JPEG files are recorded on a disc.

MP3 & WMA:

Select this to play back MP3/WMA files.

JPEG:

Select this to play back JPEG files.

ATTENTION:

When changing the settings in the ADV SET UPB menu while in the DV deck mode, the unit will switch to HDD or DVD deck mode. To proceed to DV deck after making the changes, press DV/HDD/DVD on the unit repeatedly or DV on the remote control to select the DV deck.

DV SET UP

8 DV AUDIO REC ^12BIT / 16BIT

This is the setting for sound mode before recording on a Mini DV tape.

12BIT:

Enables Audio Dubbing later.

16BIT:

Audio Dubbing is not possible but the recorded sound quality is higher than A12BITB

8 AUDIO MODE ^ SOUND1 / SOUND2 / MIX

You can select the desired sound mode when playing back an audio dubbed Mini DV tape.

SOUND1:

Original recorded sound.

SOUND2:

Audio dubbed sound.

MIX:

Original recorded sound and audio-dubbed sound.

NOTES:

● When AAUDIO MODEB is set to AMIXB, both the main and sub

audio will be audible for bilingual tapes.

● To select only the main audio or only the sub audio of bilingual

tapes, set AAUDIO MODEB to ASOUND1B.

REC/PLAY SET UP

8 XP MODE REC AUDIO ^ DOLBY DIGITAL / LINEAR PCM

You can select the audio format when you record a title in XP mode. When this function is set to ALINEAR PCMB, you can obtain a high-quality audio sound.

DOLBY DIGITAL:

To record in Dolby Digital format.

LINEAR PCM:

To record in Linear PCM format.

8 AUDIO REC ^ NICAM / MONO

You can select the desired NICAM audio channel to be recorded on a DVD-R/RW (Video mode) disc.

NICAM:

To record the main and sub language of NICAM audio.

MONO:

To record the standard (monaural) sound of NICAM audio.

NOTE:

This function works only for the NICAM bilingual programme.

8 DIRECT REC ^ OFF / ON

When this function is set to AONB, you can easily start recording the programme that you are watching on your TV. While holding R, press I on the remote control, or press R on the unit.

NOTES:

● When you use the Direct Rec function, be sure to use a TV

offering T-V LINK, etc. and connect a fully-wired 21-pin SCART cable between the unit and the TV. (A pg. 16)

● If ADIRECT RECB is set to AOFFB, the R button functions as

described in ABasic RecordingB (A pg. 32, 35).

● During Direct Rec, A––B appears on the front display panel.

● If a programme is recorded with the Direct Rec, the station name

will not be registered in the library. A––––B will be displayed for the station name.

● Even if there is no power supply for more than 60 minutes, the

unit keeps the setting.

SUBSIDIARY SETTINGS

EN 73

8 INPUT COLOUR SYSTEM ^ PAL / SECAM

You can play back PAL discs, or record PAL and SECAM signals on this unit. Select the appropriate colour system.

PAL:

To record PAL signals.

SECAM:

To record SECAM signals.

8 JUMP TIME ^ 15 MIN / 30 MIN / 1 HR

You can locate a scene ahead of or behind the currently viewed one by jumping a selected time interval during playback (or Live Memory Playback). For details, refer to AJump SearchB (A pg. 24,

38).

DISPLAY SET

8 SUPERIMPOSE ^ AUTO / ON / OFF

When this function is set to AAUTOB, various operational indicators appear on the TV screen. Messages appear in the selected language. (A pg. 20)

AUTO:

To superimpose operational indications for approximately five seconds just after the corresponding operation.

ON:

To turn on superimposed indications.

OFF:

To turn off superimposed indications.

NOTES:

● When you use this unit as the source player for editing, be sure to

set ASUPERIMPOSEB to AOFFB before starting. (A pg. 62)

● When you select AAUTOB, during playback, the operation mode

indicators may be disturbed depending on the type of disc being used.

8 ON SCREEN LANGUAGE

This unit offers you the choice to view on-screen messages in 10 different languages. Although Auto Set Up selects the language automatically (A pg. 19), you can change the language setting manually as required. For details, refer to AOn-screen Language SetB (A pg. 20)

8 BLUE BACK ^ OFF / ON

When this function is set to AONB, the TV screen becomes all blue when receiving a channel not in use.

NOTE:

When you want to receive an unstable channel with poor signals, set this function to AOFFB.

8 DIMMER ^ BRIGHT / DIMMED

You can change the brightness of the front display panel.

BRIGHT:

Normally select this.

DIMMED:

To dim the front display panel. (Blue lamp on the front display panel is turned off.)

8 POWER SAVE ^ OFF / ON

When this function is set to AONB, you can reduce the power consumption while the unit is turned off.

NOTES:

● During Power Save mode ^

^ the front display panel will be turned off. ^ the Just Clock function (A pg. 77) does not work.

● Power Save does not work when ^

^ the unit is in the Timer mode. ^ the unit’s power is turned off after timer-recording or Instant

Timer Recording.

^ the Automatic Satellite Programme Recording mode is

engaged. (A pg. 48)

^ AL-2 SELECTB is set to ADECODERB, ASAT VIDEOB or ASAT

S-VIDEOB. (A pg. 63)

● It takes some time for the unit to complete initialisation after you

turn on the unit power, with AWAKE UPB blinking on the front display panel.

74 EN

SUBSIDIARY SETTINGS

SHOWVIEW System Setup

IMPORTANT:

Normally, Auto Set Up (A pg. 17), Preset Download (A pg. 18) or Auto Channel Set (A pg. 74) sets the Guide Programme numbers automatically. You need to set the Guide Programme numbers manually only in the following cases.

● When timer-programming with the SHOWVIEW system, the

channel position, where the station you wish to record is received on your unit, is not selected,

when you add a channel after Auto Set Up, Preset Download or Auto Channel Set has taken place, ^ Set the Guide Programme number for that station manually.

● When you wish to timer-record a satellite programme with the

HOWVIEW system,

^ Set the Guide Programme numbers for all satellite

broadcasts received on your satellite receiver.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

Guide Programme Number Set

1 Press SET UP to access the Main Menu screen. 2 Press DE to select AINITIAL SET UPB, then press G. 3 Press DE to select ATUNER

SETB, then press G.

4 Press FGD E to select

AGUIDE PROG SETB, then press ENTER.

5 Press FG to select AGUIDE

PROGB, then press ENTER.

6 Press FG to select the Guide

Programme number for the desired station as shown in the TV listings. Then press ENTER.

7 Press FG to select ATV

PROGB, then press ENTER. Press FG to select the number of the unit’s channel position on which the Guide Programme number’s broadcast is received by the unit or the satellite receiver. Then press ENTER.

● Repeat steps 5 – 7 as necessary.

8 Press SET UP to complete the setting.

Guide Programme Number

AGuide Programme (GUIDE PROG) numberB refers to the assigned TV station numbers, according to broadcast area, for the S

HOWVIEW timer recording. The Guide Programme Numbers

can be found in most TV listings.

DVD VIDEO SET UP

HDD/DVD/DV SET FUNCTIO N SET UP INITIAL SET UP

TUNER SET CLOCK SET

AUTO CH SET MANUAL CH SET

ENTER

SET UP

EXIT

SET UP

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

SELECT

INITIAL SET UP > GUIDE PROG SET

GUIDE PROG

TV PROG

ENTER

SELECT WITH @ THEN PRESS [ENTER]

SELECT

PRESS [SET UP] TO EXIT

EXIT

GUIDE PROG SET

YLE2 1

RETURN

Tuner Set

Your unit needs to memorise all necessary stations in channel positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the PR +/– buttons without going through any vacant channels.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

DVDTV

ENTER

IMPORTANT:

Perform the following steps only if ^ ^ Auto Channel Set has not been set correctly by Auto Set Up

or by Preset Download. (A pg. 17, 18)

^ you have moved to a different area or if a new station starts

broadcasting in your area.

Auto Channel Set

1 Press SET UP to access the Main Menu screen. 2 Press DE to select A INITIAL SET UPB, then press G. 3 Press DE to select ATUNER SETB, then press G. 4 Press FGDE to select AAUTO

CH SETB, then press ENTER.

5 Press FGD E to select your

country’s name, then press ENTER.

6 Press FGD E to select the

language of your choice.

7 Press ENTER twice.

● When you have connected the

unit to a TV offering T-V Link via a fully-wired 21-pin SCART cable (A pg. 16), the unit automatically performs the Preset Download and the T-V LINK screen will appear. (A pg. 18)

● The Auto Set screen appears,

and remains on screen while the unit searches for receivable stations.

FGDE

SET UP

DVD VIDEO SET UP

TUNER SET

SET UP

EXIT

SELECT

INITIAL SET UP > AUTO SET

SET UP

EXIT

FUNCTION SET UP

HDD/DVD/DV SET

CLOCK SET

AUTO CH SET MANUAL CH SET

GUIDE PROG SET

ENTER

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

AUTO SET

PLEASE WAIT...

CANCEL

ENTER

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

SELECT

INITIAL SET UP

8 View the Confirmation screen.

AAUTO SET COMPLETEDB or ASCAN COMPLETEDB is displayed on the TV screen. Select AOKB.

9 Press SET UP to complete the setting.

● Using the Confirmation screen, you can skip or add channel

positions, enter station names and perform other operations. Refer to pages 75 – 76 for the procedures.

● Depending on reception conditions, the stations may not be

stored in order, and the station names may not be stored correctly.

● For information on scrambled broadcasts, refer to AWhen

Receiving A Scrambled Broadcast (HDD & DVD Deck Only)B (A pg. 76).

IMPORTANT:

● In certain reception conditions, station names may not be

stored correctly, and Auto Guide Programme Number Set may not work properly. When the Guide Programme numbers are not set properly, the programme that you do not intended to record will be timer-recorded by the S unit. When programming the timer using the S system, be sure to check the desired channel is selected correctly. (A pg. 44)

● Your unit memorises all receivable stations even if reception of

some of them is poor. You can delete those stations with an unacceptable picture from the list. (A pg. 76, ADelete A ChannelB)

NOTES:

● Fine tuning is performed automatically during Auto Channel Set.

If you want to perform tuning manually, refer to AFine-Tuning Channels Already StoredB (A pg. 76).

● If you perform Auto Channel Set when the aerial cable is not

connected properly, ASCAN COMPLETED –NO SIGNAL–B appears on the TV screen in step 8. In such a case, make sure of the aerial connection and press ENTER; Auto Channel Set will start again.

● If no sound accompanies the picture or the audio sounds

HOWVIEW system of the

HOWVIEW

SUBSIDIARY SETTINGS

EN 75

Manual Channel Set

Store channels that were not stored during Auto Set Up (A pg. 17), Preset Download (A pg. 18) or Auto Channel Set (A pg. 74).

1 Press SET UP to access the Main Menu screen. 2 Press DE to select A INITIAL SET UPB, then press G. 3 Press DE to select ATUNER SETB, then press G. 4 Press FGD E to select AMANUAL CH SETB, then press

ENTER. The Manual Channel Set screen appears.

5 Press DE to select AEDITB, then press ENTER. 6 Press FGD E to select a blank

position in which you want to store a channel, then press ENTER. The Confirmation screen appears.

7 Press FG to select ABANDB,

then press ENTER.

8 Press FG to change the band

between CH (regular) and CC (cable), then press ENTER.

9 Press FG to select ACHB, then

press ENTER.

10 Press FG to input the

channel number you want to store.

● To enter the registered

station name (A pg. 89), press FG to select AIDB, then press ENTER. Press FG.

● For fine tuning adjustment, press FG to select AFINEB, then

press ENTER. Press FG to perform fine-tuning.

● When storing a channel that sends scrambled broadcasts,

press FG to select ADECODERB, then press ENTER. Press FG to set ADECODERB to AONB (AOFFB is the default setting).

● When AL-2 SELECTB is set to AVIDEOB, AS-VIDEOB, ASAT

VIDEOB or ASAT S-VIDEOB, the ADECODERB setting cannot be changed. (A pg. 63)

11 Press ENTER to enter new channel information. The

Confirmation screen appears.

12 Press SET UP or RETURN to close the Confirmation screen.

● To change positions, see AChange Station Channel PositionB

(A pg. 76).

● If you wish to set station names other than the ones registered

in your unit, see ASet Stations (B)B (A pg. 76).

(Example) To store in position 12.

INITIAL SET UP > MANUAL CH SET

PR PR

01 C01 ----

CTEA

03 05 1000

04 C79 3SAT

9LIV

05 01

AB3

The programme currently received on the selected channel position appears behind the confirmation screen.

INITIAL SET UP > MANUAL CH SET

BAND

FINE

DECODER

SET UP

EXIT

MOVE

ENTER

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

SELECT

07 ----

08 ----

09 ----

10 ----

11 ----

12 ----

EDIT RETURN

----

OFF

RETURN

ATTENTION:

Guide Programme numbers are not set when channels are stored manually. (A pg. 74, AS

HOWVIEW System SetupB)

76 EN

SUBSIDIARY SETTINGS

Delete A Channel

1 Perform steps 1 – 5 of AManual Channel SetB (A pg. 75). 2 Press FGD E to select the channel you want to delete. 3 Press CANCEL(L) to delete a channel. The channel next to

the cancelled one moves up one line.

● Repeat steps 2 – 3 as necessary.

4 Press SET UP or RETURN to close the Confirmation screen.

Change Station Channel Position

1 Perform steps 1 – 4 of AManual Channel SetB (A pg. 75). 2 Press DE to select AMOVEB, then press ENTER. 3 Press FGD E to select the channel you want to move, then

press ENTER.

4 Press FGD E to select the new channel position, then press

ENTER.

Example: If you moved the station in position 4 to position 2, the

stations originally in positions 2 and 3 each move down one space.

INITIAL SET UP > MANUAL CH SET

02 CTEA

C79

9LIV

AB3

MOVE

07 ----

08 ----

09 ----

10 ----

11 ----

12 ----

RETURN

EDIT

01 C01 ----

03 05 1000

04 3SAT

05 01

● Repeat steps 3 – 4 as necessary.

INITIAL SET UP > MANUAL CH SET

01 C01 ----

C79

3SAT

03 02

CTEA

04 05

1000

9LIV

05 01

AB3

07 ----

08 ----

09 ----

10 ----

11 ----

12 ----

MOVE

RETURN

EDIT

5 Press SET UP or RETURN to close the Confirmation screen.

When Receiving A Scrambled Broadcast (HDD & DVD Deck Only)

1 Set AL-2 SELECTB to ADECODERB. (A pg. 63) 2 Perform steps 1 – 5 of AManual Channel SetB (A pg. 75). 3 Press FGD E to select the channel position broadcasting

scrambled programmes, then press ENTER. The Confirmation screen appears.

4 Press FG to select ADECODERB, then press ENTER. 5 Press FG to set ADECODERB to AONB, then press ENTER. 6 Press RETURN to return to the Manual Channel Set screen.

● Repeat steps 3 – 5 as necessary.

7 Press SET UP or RETURN to close the Confirmation screen.

INFORMATION

If you live in Eastern Europe, ATV SYSTEMB setting appears instead of ADECODERB setting on the Manual Channel Set screen. When you can see the picture but can hear no audio, select appropriate TV system (D/K or B/G). Normally, TV programmes are broadcast as follows. For Eastern Europe : D/K For Western Europe : B/G A Select a country in Eastern Europe in step 5 of AAuto

Channel SetB (A pg. 74).

B Press FG to select ATV SYSTEMB in step 7 of AManual

Channel SetB (A pg. 75).

C Press FG to select appropriate TV System (D/K or B/G).

Set Stations (A)

Set station names that are registered in your unit.

1 Perform steps 1 – 5 of AManual Channel SetB (A pg. 75). 2 Press FGD E to select the channel you want to modify, then

press ENTER. The Confirmation screen appears.

3 Press FG to select AIDB, then press ENTER. 4 Move the arrow to the left ID selection column. Registered

station names (ID) (A pg. 89) appear as you press FG.

5 Press ENTER to select the desired ID, then press ENTER

again to select AOKB.

6 Press RETURN to return to the Manual Channel Set screen.

● Repeat steps 2 – 5 as necessary.

7 Press SET UP or RETURN to close the Confirmation screen.

Set Stations (B)

Set station names other than the ones registered in your unit.

1 Perform steps 1 – 5 of AManual Channel SetB (A pg. 75). 2 Press FGD E to select the channel you want to modify, then

press ENTER. The Confirmation screen appears.

3 Press FG to select AIDB, then press ENTER. 4 Press FGD E to select the desired characters (A–Z, 0–9, –, Z,

+, & (space)), then press ENTER.

● Enter the remaining characters the same way (maximum of 4).

5 After entering all characters, press FGD E to select AOKB, then

press ENTER.

6 Press RETURN to return to the Manual Channel Set screen.

● Repeat steps 2 – 5 as necessary.

7 Press SET UP or RETURN to close the Confirmation screen.

NOTE:

The characters available for the station name (ID) are A–Z, 0–9, –, Z, +, & (space) (maximum of 4).

Fine-Tuning Channels Already Stored

1 Perform steps 1 – 5 of AManual Channel SetB (A pg. 75). 2 Press FGD E to select the channel you want to fine-tune, then

press ENTER. The Confirmation screen appears.

3 Press FG to select AFINEB, then press ENTER. 4 Press FG until the picture appears in its best quality, then

press ENTER.

● Repeat steps 2 – 4 as necessary.

5 Press RETURN to return to the Manual Channel Set screen. 6 Press SET UP or RETURN to close the Confirmation screen.

Clock Set

IMPORTANT:

If you performed Auto Set Up (A pg. 17) or Preset Download (A pg. 18), without ever having set the clock previously, the unit’s built-in clock is also set automatically. Perform the following steps only if ^ ^ Auto Clock Set has not been performed correctly by Auto Set

Up or Preset Download.

^ you want to change Just Clock setting. (See AJust ClockB in

the right column)

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

DVDTV

ENTER

FGDE

SET UP

SUBSIDIARY SETTINGS

6 Press FG to select ATV PROGRAMMEB

, then press

EN 77

ENTER.

Press FG to set the channel position to the number representing the station transmitting clock setting data, then press ENTER.

● The unit is preset to receive clock setting and adjustment data

from channel position 1.

7 Press SET UP to start the clock operation.

NOTES:

● Just Clock (when set to AONB) adjusts the unit’s built-in clock

every hour, except for 23:00, 0:00, 1:00 and 2:00.

● Just Clock is not effective when:

^ the unit’s power is on. ^ the unit is in the Timer mode. ^ a difference of more than 3 minutes exists between the built-in

clock’s time and the actual time.

^ the unit is in the Automatic Satellite Programme Recording

mode. (A pg. 48) (HDD deck only)

^ the unit is in the Power Save mode. (A pg. 73) ^ AL-2 SELECTB is set to ASAT VIDEOB or ASAT S-VIDEOB.

(A pg. 63)

● If Just Clock is set to AONB, the unit’s clock is automatically

adjusted at the start/end of Summer Time.

● Just Clock may not function properly depending on the reception

condition.

Just Clock

The Just Clock function provides accurate time keeping through automatic adjustments at regular intervals, by reading data from a PDC signal. The Just Clock option can be set to AONB or AOFFB at the Clock Set screen (the default setting is AOFFB).

IMPORTANT:

If you turn off Just Clock, the accuracy of your unit’s built-in clock may be reduced, which could adversely effect timer recording. We recommend you to keep Just Clock on. In cases where the clock setting data from a PDC signal is incorrect, however, you are advised to keep Just Clock set to AOFFB.

1 Press SET UP to access the Main Menu screen. 2 Press DE to select AINITIAL SET UPB, then press G. 3 Press DE to select ACLOCK

SETB, then press G.

NOTE:

When you have selected

AMAGYARORSZÁGB, AČESKÁ REPUBLIKAB, APOLSKAB or

AOTHER EASTERNB for the country setting (A pg. 17), you cannot use Just Clock function. Skip steps 5 and 6.

DVD VIDEO SET UP

TUNER SET CLOCK SET

YEAR

DATE

TIME

JUST CLOCK

TV PROGRAMME

ENTER

SET UP

EXIT

SELECT

HDD/DVD/DV SET UP

FUNCTION SET UP

SELECT WITH @ THEN PRESS [ENTER]

PRESS [SET UP] TO EXIT

2004

01. 01 THU

--:--

OFF

INITIAL SET UP

4 Press FG to select AYEARB, then press ENTER. Press FG to

set the year, then press ENTER.

● Repeat the same procedure to set the date and time.

● When you set the date, press and hold FG to change the date

by 15 days interval.

● When you set the time, press and hold FG to change the time

by 30 minutes interval.

5 Press FG to select AJUST CLOCKB, then press ENTER. Press

FG to set to the desired mode, then press ENTER.

● The default setting is AOFFB.

● For the Just clock function, refer to AJust ClockB on the right

column.

● If you set to AOFFB, you can disregard the next step as you

won’t be able to receive regular clock adjustments.

78 EN

SUBSIDIARY SETTINGS

Format A Disc (DVD Deck Only)

Some DVD-RAM/RW discs are unformatted. Format the disc when you use an unformatted disc or you want to delete all recordings and data on the disc.

ATTENTION:

● When a disc is formatted, all recordings and data are erased. It

is impossible to restore them.

● Never turn off the unit or disconnect the mains power cord

while ANOW FORMATTING...B is displayed on the TV screen.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Load a DVD-RAM/RW disc to format.

CABLE/SAT

DVDTV

ENTER

FGDE

SET UP

Format A DVD-RAM Disc

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press SET UP to access the Main Menu screen. 3 Press DE to select A HDD/DVD/DV SET UPB, then press G. 4 Press DE to select ADISC SET

UPB, then press G.

5 Press FGD E to select

AFORMATB, then press

ENTER. Press DE to select AOKB, then press ENTER.

6 Press DE to select

AEXECUTEB, then press

ENTER.

DVD VIDEO SET UP

HDD/DVD/DV SET UP

HDD SET UP DVD SET UP

ENTER

SET UP

EXIT

SELECT

FUNCTION SET UP

DISC SET UP DV SET UP

CANC. FINALIS.

FINALISE

Video

SELECT WITH @ THEN PRESS [ENTER] PRESS [SET UP] TO EXIT

Video

FORMAT

INITIAL SET UP

Format A DVD-RW Disc

1 Perform steps 1 to 4 of AFormat A DVD-RAM DiscB as above

before continuing.

2 Press FGD E to select AFORMATB, then press ENTER. Press

DE to choose AVR MODEB or AVIDEO MODEB, then press

ENTER when ADISC WILL BE FORMATTEDB appears on the TV screen.

AVR MODEB:

To be chosen when you want to record, erase, or edit data on the disc repeatedly.

AVIDEO MODEB:

To be chosen when you want to erase all the data on the disc once played back to record new data, or play back the disc on other DVD players.

3 Press DE to select A EXECUTEB, then press ENTER.

NOTES:

● It is impossible to format Version 1.0 DVD-RW discs in Video

mode.

● It is impossible to format DVD-R discs.

● All the titles on a disc will be deleted once the disc is formatted

even if they are protected titles. (A pg. 51)

SUBSIDIARY SETTINGS

EN 79

Finalise A Disc (DVD Deck Only)

Finalising DVD-R/RW discs recorded on this unit makes it possible for the discs to be played back on other DVD players. DVD-RW discs are finalised in the mode that the discs were formatted, enabling playback on compatible DVD players. Title names input in the Library Database Navigation are registered as title names in the DVD menu. (A pg. 50)

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

● Load a DVD-R/RW disc to finalise.

CABLE/SAT

DVDTV

ENTER

FGDE

SET UP

Finalise A DVD-R/RW Disc

1 Perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 78)

before continuing.

2 Press FGD E to select AFINALISEB, then press ENTER.

● For DVD-R/RW (Video mode) discs, the background selection

screen will appear. Press FGDE to select the desired background from a selection of 18 backgrounds, then press ENTER.

3 Press DE to select AOKB, then press ENTER. 4 Upon completing finalisation, ACOMPLETEDB appears on the

TV screen. Press ENTER to end.

5 Press SET UP to return to the normal screen.

● Menu screen is cleared.

● Once a DVD-R/RW (Video mode) disc has been finalised, the

displays for original and play list do not appear. Only display for library appears.

● Once a DVD-RW (VR mode) disc has been finalised, it can be

played on DVD players compatible with VR mode.

Cancel The Finalisation Of A DVD-RW Disc

1 Load a DVD-RW disc to cancel the disc finalisation, and

perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 78) before continuing.

2 Press FGD E to select ACANC. FINALIS.B, then press ENTER. 3 Press DE to select A EXECUTEB, then press ENTER. 4 Upon completing cancellation of finalisation, ACANCELLATION

COMPLETEDB appears on the TV screen. Press ENTER to end.

5 Press SET UP to return to the normal screen.

● When the disc finalisation is cancelled, the mode in which the

disc was formatted is restored, making the disc recordable. (A pg. 7, 78)

Before finalising

● It is possible to record on a blank space.

● It is possible to enter title names. (A pg. 50)

● It is possible to delete titles. (A pg. 51)

● It is impossible to overwrite recorded areas of DVD-R discs.

● Available recording capacity does not increase even if a recorded

title is deleted from a DVD-R disc.

● It is impossible to record or edit DVD-R/RW discs recorded on

other devices even if they have not been finalised.

After finalising (For DVD-R/RW (Video mode) discs)

● Video and audio that have been recorded by then are recorded in

conformity to the DVD Video standard, enabling you to play back the discs as DVD VIDEO discs.

● Although DVD-R/RW discs finalised on this unit become playable

on DVD players compatible with DVD-R/RW discs, some discs still may not play, for which JVC cannot take responsibility.

● Marked points marked before finalising will be deleted, and titles

will be divided automatically into AchaptersB approximately every 5 minutes. (A pg. 25)

● Depending on the DVD players and DVD-R/RW discs used, and

on the conditions of recording, it may not be possible to play back the discs. In this case, play back the discs on this unit.

● Additional recordings become impossible.

80 EN

SUBSIDIARY SETTINGS

Scan Mode Set (HDD & DVD Deck Only)

If you connect the unit and TV with Component Video Connection (A pg. 16), you can select the scan mode from two modes: Interlaced scan mode which is used in the conventional TV system, and Progressive scan mode which enables reproduction of higher-quality images.

8 Interlaced scan

In the conventional video system, a picture is shown on the display monitor in two halves. The Interlaced scan system places lines of the second half of the picture in-between lines of the first half of the picture.

8 Progressive scan

Progressive scan displays all the horizontal lines of a picture at one time, as a single frame. This system can convert the interlaced video from DVD into progressive format for connection to a progressive display. It dramatically increases the vertical resolution.

ATTENTION:

Your TV needs to be compatible with PAL Progressive.

● Turn on the unit.

● Turn on the TV and select the AV mode.

● Slide the TV/CABLE/SAT/DVD switch to DVD.

CABLE/SAT

DVDTV

HDD

DVD

Tray Lock (DVD Deck Only)

You can lock the disc tray to prohibit the unwanted disc ejection by children.

● Turn off the unit.

To lock tray

While the unit is turned off, press and hold o, then press M on the unit. ALOCKB appears on the front display panel and the disc tray is locked.

To unlock tray

While the unit is turned off, press and hold o, then press M on the unit. AUNLOCKB appears on the front display panel.

Mode Lock

When the unit is turned on, press and hold ENTER on the remote control for more than 5 seconds. ALOCKB appears on the front display panel.

● No buttons will function and playback and recording will not be

interrupted.

● When the unit is in the stop mode, all buttons will not function

except R and I. To cancel Mode Lock, press and hold ENTER again for more than 5 seconds.

NOTE:

It is also possible to use Mode Lock during Repeat Playback (A pg. 27).

PROGRESSIVE SCAN

1 Press HDD or DVD so that the HDD or DVD lamp lights up on

the unit.

2 Press PROGRESSIVE SCAN for 3 or more seconds.

● Video output indicator (q) lights on the front display panel if

Progressive scan mode has been established. (A pg. 12)

● Each press of PROGRESSIVE SCAN for 3 or more seconds

switches the scan mode.

NOTES:

● When the progressive mode is set, be sure to set AL-1 OUTPUTB

to ACOMPONENTB (A pg. 63). Progressive scan is output only from [COMPONENT VIDEO OUT] connector.

● Interlaced scan mode is the setting at your purchase.

● Interlaced scan mode might be suitable depending on video

material.

● Scan mode cannot be set while menu screen is displayed.

● When the Progressive scan mode is engaged, no video signal is

output from [L-1 IN/OUT] connector.

Last Function Memory

When the power plug is disconnected from unit or when power failure occurs, your settings for the following functions are kept in the memory. These settings will resume when the unit is turned on again.

● Input selection (channel or auxiliary input; L-1, L-2, F-1 or DV)

● Recorder selection (The last selected deck is memorised.)

● Country setting (A pg. 17)

● Recording speed (A pg. 32, 35)

● Mode settings (A pg. 71 – 73)

Before requesting service for a problem, use this chart and see if you can solve the trouble yourself. Small problems are often easily solved, and this can save you the trouble of sending your unit off for repair.

Initialising (DVD Deck Only)

Malfunction occurs on the unit.

] Press A to turn off the unit, press and hold A, then press o

for two seconds or more.

General

No power is supplied to the unit.

● The AC power plug is disconnected from the mains outlet.

] Connect the AC power plug to the mains outlet securely.

(A pg. 16)

The remote control does not work properly.

] Remove the batteries, wait for 5 minutes or more, then load the

butteries again.

● The setting of the remote control code is inappropriate.

] Set the same remote control code (1, 2, 3, or 4) on both the unit

and the remote control. (A pg. 67)

● The batteries are discharged.

] Replace the dead batteries with new ones.

Dubbing from the external equipment is not possible.

● The source (another video recorder, camcorder) has not been

properly connected.

] Confirm that the source is properly connected.

● All necessary power switches have not been turned on.

] Confirm that all units’ power switches are turned on.

● The setting of the input channel position is inappropriate.

] Select the input channel position (AF-1B, AL-1B or AL-2B) that

corresponds to the input terminal connected to the external equipment. (A pg. 62)

The on-screen display superimposed on the programme played back/received on this unit is recorded when you dub the programme to an external recording equipment.

] Set ASUPERIMPOSEB to AOFFB. (A pg. 73)

The unit does not operate.

● There are cases when the operation is prohibited on the disc.

● Lightning or static electricity may cause malfunction of the unit.

] Press A to turn the power off, then press the button again to

turn the power on.

The remote control of a JVC TV will not operate the unit.

● The setting of the remote control code is inappropriate.

] To operate the unit using a JVC TV remote control, set the

remote control code of the unit to A1B (Default: A3B). (A pg. 67)

TROUBLESHOOTING

EN 81

Playback (DVD Deck)

The DVD deck cannot be operated.

● The DVD deck is not selected.

] Press DV/HDD/DVD on the unit repeatedly or DVD on the

remote so that the DVD lamp lights up on the unit.

Images do not appear on the TV screen.

● The TV receiver’s channel selector is not set to the AV mode.

] Set the TV to its AV mode.

● When interlace scanned programme is played back,

progressive scan mode is selected.

] Press and hold PROGRESSIVE SCAN until q disappears

from the front display panel. (A pg. 80)

Playback does not start or stop immediately after playback is started by pressing I. On the front display panel, ANO DISCB appears.

● The disc is loaded upside down.

] Place the disc on the disc tray with the playback surface facing

down. (A pg. 8)

● A disc not being compatible with the unit is loaded.

] Load a playable disc on the unit. (A pg. 5)

● A dirty disc is loaded.

] Clean the disc. (A pg. 9)

● Defective disc is loaded.

] Replace the warped or scratched disc with a normal one.

Images are blurred or distorted when you start High-Speed Search.

] Images are blurred or distorted at the point where the playback

speed changes and this is not a malfunction of the unit.

Playback does not start.

] Playback does not start for approximately 30 seconds after

recording is stopped and this is not a malfunction of the unit.

Playback does not start when you select a title or a chapter.

● The Parental Lock is engaged and the disc is rated higher than

the set level.

] Release the Parental Lock temporarily or change the set level.

(A pg. 31)

Playback (HDD Deck)

The HDD deck cannot be operated.

● The HDD deck is not selected.

] Press DV/HDD/DVD on the unit repeatedly or HDD on the

remote so that the HDD lamp lights up on the unit.

82 EN

TROUBLESHOOTING

Playback (DV Deck)

The DV deck cannot be operated.

● The DV deck is not selected.

] Press DV/HDD/DVD on the unit repeatedly or DV on the remote

so that the DV lamp lights up on the unit.

The tape will not rewind or fast-forward.

● The tape is already fully rewound or fast-forwarded.

] Check the cassette.

The playback picture does not appear while the tape is running.

● The TV is not set to the AV mode.

] Set the TV to the AV mode.

Noise appears during visual search.

● This is normal.

The playback picture is blurred or interrupted while TV broadcasts are clear or AUSE CLEANING CASSETTEB message appears on the screen.

● The video heads may be dirty.

] Use a dry cleaning cassette M-DV12CL, or consult your JVC

dealer.

Recording (DVD Deck)

The desired programme cannot be recorded.

● The channel position does not correspond to that in the

receiving area.

] Set the correct channel position for the receiving broadcast.

(A pg. 74)

Recording cannot be made.

● No disc or a disc not being compatible with the unit is loaded.

] Load a recordable disc on the unit. (A pg. 5)

● The disc loaded is not formatted.

] Format the disc. (A pg. 78)

● A finalised DVD-R disc is loaded.

] Recording cannot be made on finalised discs. Load a

recordable disc on the unit.

● The disc is full or does not have enough space for the title to be

recorded.

] Clear unnecessary titles on the disc or load a blank disc.

(A pg. 51)

● The DVD-RAM disc loaded has had its protect tab slid to the

protect position.

] Release the protect tab. (A pg. 8)

Recording (HDD Deck)

TV broadcasts cannot be recorded.

● AL-1B, AL-2B or AF-1B has been selected as the input mode.

] Set to the desired channel.

Camcorder recording is not possible.

● The camcorder has not been properly connected.

] Confirm that the camcorder is properly connected.

● The input mode is not correct.

] Set the input mode to AF-1B. (A pg. 61)

Recording (DV Deck)

During recording, the tape does not run. The DV recording lamp lights up on the unit.

● The unit is in the Record Pause mode.

] Press I to resume recording.

Recording cannot be done.

● There is no cassette loaded, or the cassette loaded has had its

erase protection switch set to ASAVEB.

] Insert a Mini DV cassette, or set the erase protection switch set

to ARECB.

Camcorder recording is not possible.

● The camcorder has not been properly connected.

] Confirm that the camcorder is properly connected.

● The input mode is not correct.

] Set the input mode to AF-1B or ADV B.

The tape is automatically rewound, then the unit is shut off.

● The end of the tape was reached during recording.

] The programme may not have been recorded in its entirety.

Next time make sure you have enough time on the tape to record the entire programme.

Audio dubbing is not possible.

● ADV AUDIO RECB had been set to A16BITB at the original

recording.

] Set ADV AUDIO RECB to A12BITB at the original recording.

● The tape speed had been set to LP at the original recording.

] Set the tape speed to SP at the original recording.

Monitoring the audio dubbed sound is not possible during audio dubbing.

] This is normal. Monitor the sound using the connected devices.

TROUBLESHOOTING

EN 83

Timer Recording (HDD & DVD Deck)

Timer programming cannot be made.

● Date and time is not correct.

] Set date and time correctly. (A pg. 77)

● Timer recording is in progress.

] Timer programming can’t be performed while a timer recording

is in progress. Wait until it finishes.

Timer programming recording does not start.

● Date and time is not correct.

] Set date and time correctly. (A pg. 77)

SHOWVIEW Timer Programming cannot be made.

● Date and time set on the unit is not correct.

] Set date and time correctly. (A pg. 77)

● The channel position does not correspond to that in the

receiving area.

] Set the correct channel position for the receiving broadcast.

(A pg. 74)

The SHOWVIEW system does not timer-record properly.

● The unit’s channel positions have been set incorrectly.

] Refer to AS

the procedure.

Automatic Satellite Programme Recording does not start.

● The satellite receiver is not connected properly to this unit.

] Connect the satellite receiver to the [L-2 IN/DECODER]

connector properly. (A pg. 48)

On the front display panel, A––:––B appears.

● Power failure occurred.

] Set date and time correctly. (A pg. 77)

APROGRAMME FULLB appears on the TV screen during timer programming.

● 16 programmes have already been timer programmed.

] Clear unnecessary programmes on the unit, then try timer

programming again. (A pg. 47)

The disc space does not increase when recorded titles are cleared.

● The PC’s data recorded on a DVD-RAM drive cannot be

cleared on this unit.

] Format the disc. (When the disc is soiled, wipe the disc with a

soft dry cloth before formatting.) (A pg. 9, 78)

HOWVIEW System SetupB (A pg. 74) and reperform

JVC SR-DVM70EU User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual