JVC SR-DVM70AG, SR-DVM70EU Service Manual

SERVICE MANUAL

DVD / HDD & Mini DV VIDEO RECORDER

YD04920054

SR-DVM70AG, SR-DVM70EU

CABLE/SAT

DVD

TV

STANDBY/ON

DVD

TV/CBL/SAT

TV

AV

TV

VIDEO

DV HDD DVD

TV

PR

AUX

CANCEL

MEMO/MARK

PROGRAMME

EDITDUBBING

LIVE

NAVIGATIONTOPME NU

ENTER

RETURN

MENU

NEXTPREVIOUS

SLOWSLOW PLAY/SELECT

CLEAR

PAUSEREC

STOP/

JUMP

RECMODE

DISPLAY

ONSCREEN

REMAIN

VPS/PDC

AUDIO

SUBTITLE

ANGLE

LIVECHECK

SETUP

PROGRESSIVE

OPERATE

EJECTEJECTDISPLAY

DV/HDD/DVD REC MODE INSTANTREPLAY AUDIODUB. INSERT

SAT

SCAN

S-VIDEO

VIDEO(MONO)L - AUDIO - R

INF-1

INPUTSELECT

RECDVDRECHDDRECDV

RECPAUSEPLAY

FFREWSTOP

DVIN / OUT

(AG model)

SR-DVM70AG, SR-DVM70EU [D4MC29]

(EU model)

TABLE OF CONTENTS

1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11

5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-35

COPYRIGHT © 2005 Victor Company of Japan, Limited

No.YD049

2005/4

SPECIFICATION

SR-DVM70AG SR-DVM70EU

GENERAL

Power requirement AC 220 V ~ 240 V, 50 Hz/60 Hz

Power consumption

Power on 45 W
Power off 18 W

Temperature

Operating 5°C to 35°C

Storage -20°C to 60°C

Operating position Horizontal only

Dimensions (W × H × D) 435 mm × 96 mm × 372 mm

Weight 6.2 kg

Input/Output

Video input 0.5 - 2.0 Vp-p, 75 Ω (pin jack)

Video output 1 Vp-p, 75 Ω (BNC)

Audio input -8 dB, 50 kΩ (pin jack), Corresponding to mono (left)

Audio output -8 dB, 1 kΩ (pin jack)

21-pin SCART connectors IN/OUT × 1, IN/DECODER × 1

S-video input Y: 0.8 - 1.2 Vp-p, 75 Ω, C: 0.2 - 0.4 Vp-p, 75 Ω

S-video output Y: 1.0 Vp-p, 75 Ω, C: 0.3 Vp-p, 75 Ω

DV 4-pin for DV IN/OUT

Component video output Y: 1.0 Vp-p, 75 Ω, CB/CR, PB/PR: 0.7 Vp-p, 75 Ω

Remote Input Ø3.5 mm

Digital audio output Optical: -18 dBm, 660 nm, Coaxial: 0.7 Vp-p, 75 Ω,

VIDEO/AUDIO (DVD deck)

Recording time Maximum 8 hours (with 4.7 GB disc)

Audio recording system Dolby Digital (2 ch), Linear PCM (XP mode only)

Video recording compression system MPEG2 (CBR/VBR)

VIDEO/AUDIO (HDD Deck)

Video recording compression system MPEG2 (VBR)

Audio recording system Dolby Digital (2 ch), Linear PCM (XP mode only)

Recording time Maximum 300 hours (with 160 GB HDD)

VIDEO/AUDIO (DV Deck)

Signal system PAL colour signal, 625 lines/50 fields

Recording system Digital Component Recording

Format DV format (SD mode)

Cassette Mini DV Cassette

Maximum recording time

(SP) (SP): 80 min. with M-DV80ME cassette

(LP) (LP): 120 min. with M-DV80ME cassette

Audio recording system PCM 48 kHz, 16 bit (2 ch)/32 kHz, 12 bit (4 ch)

TUNER/TIMER

Tuning system Frequency synthesized tuner

Channel coverage VHF : 47 MHz - 89 MHz/104 MHz - 300 MHz/302 MHz - 470 MHz

Memory backup time Approx. 60 minutes

ACCESSORIES

Provided accessories

RF cable, Input Cable Adapter, Output

Cable Adapter, Audio/Video Cable, Infrared

remote control unit, "R6" battery × 2

Corresponding to Dolby Digital and DTS Digital Surround

Bit stream Selectable in digital audio output setting menu

(XP): Approx. 1 hour, (SP): Approx. 2 hours, (LP): Approx. 4 hours

(EP): Approx. 6 hours, (FR): Approx. 1 hour - 8 hours

(XP): Approx. 34 hours, (SP): Approx. 69 hours, (LP): Approx. 138 hours

• Specifications shown are for SP mode unless otherwise specified.

• E.& O.E. Design and specifications subject to change without notice.

• Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby Laboratories.

• "DTS" and "DTS Digital Out" are trademarks of Digital Theater Systems, Inc.

• Cassettes marked Mini DV can be used with the DV deck of this unit. The DV deck can play back and record only PAL signals.

• SHOWVIEW is a trademark of Gemstar Development Corporation. The SHOWVIEW system is manufactured under licence from Gemstar Devel­opment Corporation.(EU MODEL)

• G-CODE is registered trademarks of Gemstar Development Corporation. The G-CODE system is manufactured under license from Gemstar De­velopment Corporation.(AG MODEL)

• (i.Link) refers to the IEEE1394-1995 industry specification and extensions thereof. The logo is used for products compliant with the i.Link stan­dard.

Corresponding to copy protection

(EP): Approx. 209 hours, (FR): Approx. 300 hours

UHF : 470 MHz - 862 MHz

RF cable, 21-pin SCART cable,

SCART/RCA adapter × 2, Infrared remote

control unit, "R6" battery × 2

1-2 (No.YD049)

SECTION 1

r

PRECAUTION

1.1 SAFTY PRECAUTIONS

Prior to shipment from the factory, JVC products are strictly in­spected to conform with the recognized product safety and elec­trical codes of the countries in which they are to be
sold.However,in order to maintain such compliance, it is equally
important to implement the following precautions when a set is
being serviced.

1.1.1 Precautions during Servicing

(1) Locations requiring special caution are denoted by labels

and inscriptions on the cabinet, chassis and certain parts of
the product.When performing service, be sure to read and
comply with these and other cautionary notices appearing
in the operation and service manuals.

(2) Parts identified by the symbol and shaded ( ) parts

are critical for safety.
Replace only with specified part numbers.

NOTE :

Parts in this category also include those specified to
comply with X-ray emission standards for products
using cathode ray tubes and those specified for
compliance with various regulations regarding spu­rious radiation emission.

(3) Fuse replacement caution notice.

Caution for continued protection against fire hazard.
Replace only with same type and rated fuse(s) as speci­fied.

(4) Use specified internal wiring. Note especially:

• Wires covered with PVC tubing

• Double insulated wires

• High voltage leads

(5) Use specified insulating materials for hazardous live parts.

Note especially:

• Insulation Tape

• PVC tubing

•Spacers

• Insulation sheets for transistors

•Barrier

(6) When replacing AC primary side components (transformers,

power cords, noise blocking capacitors, etc.) wrap ends of
wires securely about the terminals before soldering.

Consequently, when servicing these products, replace the
cathode ray tubes and other parts with only the specified
parts. Under no circumstances attempt to modify these cir­cuits.Unauthorized modification can increase the high volt­age value and cause X-ray emission from the cathode ray
tube.

(12) Crimp type wire connectorIn such cases as when replacing

the power transformer in sets where the connections be­tween the power cord and power trans former primary lead
wires are performed using crimp type connectors, if replac­ing the connectors is unavoidable, in order to prevent safe­ty hazards, perform carefully and precisely according to the
following steps.

• Connector part number :E03830-001

• Required tool : Connector crimping tool of the proper
type which will not damage insulated parts.

• Replacement procedure

a) Remove the old connector by cutting the wires at a

point close to the connector.Important : Do not re­use a connector (discard it).

cut close to connector

Fig.1-1-3

b) Strip about 15 mm of the insulation from the ends

of the wires. If the wires are stranded, twist the
strands to avoid frayed conductors.

15 mm

Fig.1-1-4

c) Align the lengths of the wires to be connected. In-

sert the wires fully into the connector.

Metal sleeve

Fig.1-1-1

(7) Observe that wires do not contact heat producing parts

(heatsinks, oxide metal film resistors, fusible resistors, etc.)

(8) Check that replaced wires do not contact sharp edged or

pointed parts.

(9) When a power cord has been replaced, check that 10-15

kg of force in any direction will not loosen it.

Power cord

Fig.1-1-2
(10) Also check areas surrounding repaired locations.
(11) Products using cathode ray tubes (CRTs)In regard to such

products, the cathode ray tubes themselves, the high volt­age circuits, and related circuits are specified for compli­ance with recognized codes pertaining to X-ray emission.

Connector

Fig.1-1-5

d) As shown in Fig.1-1-6, use the crimping tool to

crimp the metal sleeve at the center position. Be
sure to crimp fully to the complete closure of the
tool.

1.2
5

2.0

5.5

Crimping tool

Fig.1-1-6

e) Check the four points noted in Fig.1-1-7.

Not easily pulled free

Wire insulation recessed

more than 4 mm

Crimped at approx. cente

of metal sleeve

Conductors extended

Fig.1-1-7

(No.YD049)1-3

1.1.2 Safety Check after Servicing

Examine the area surrounding the repaired location for damage
or deterioration. Observe that screws, parts and wires have been
returned to original positions, Afterwards, perform the following
tests and confirm the specified values in order to verify compli­ance with safety standards.

(1) Insulation resistance test

Confirm the specified insulation resistance or greater be­tween power cord plug prongs and externally exposed
parts of the set (RF terminals, antenna terminals, video and
audio input and output terminals, microphone jacks, ear­phone jacks, etc.).See table 1 below.

(2) Dielectric strength test

Confirm specified dielectric strength or greater between
power cord plug prongs and exposed accessible parts of
the set (RF terminals, antenna terminals, video and audio
input and output terminals, microphone jacks, earphone
jacks, etc.). See Fig.1-1-11 below.

(3) Clearance distance

When replacing primary circuit components, confirm spec­ified clearance distance (d), (d') between soldered termi­nals, and between terminals and surrounding metallic
parts. See Fig.1-1-11 below.

d

Chassis

d'

Power cord
primary wire

Fig.1-1-8

(4) Leakage current test

Confirm specified or lower leakage current between earth
ground/power cord plug prongs and externally exposed ac­cessible parts (RF terminals, antenna terminals, video and
audio input and output terminals, microphone jacks, ear­phone jacks, etc.).
Measuring Method : (Power ON)Insert load Z between
earth ground/power cord plug prongs and externally ex­posed accessible parts. Use an AC voltmeter to measure
across both terminals of load Z. See Fig.1-1-9 and follow­ing Fig.1-1-12.

ab

Externally
exposed
accessible part

Z

V

c

A

Fig.1-1-9

(5) Grounding (Class 1 model only)

Confirm specified or lower grounding impedance between
earth pin in AC inlet and externally exposed accessible
parts (Video in, Video out, Audio in, Audio out or Fixing
screw etc.).Measuring Method:
Connect milli ohm meter between earth pin in AC inlet and
exposed accessible parts. See Fig.1-1-10 and grounding
specifications.

AC inlet

Earth pin

Exposed accessible part

MIlli ohm meter

Grounding Specifications

Region

USA & Canada

Europe & Australia

Grounding Impedance (Z

Z 0.1 ohm

Z 0.5 ohm

)

Fig.1-1-10

AC Line Voltage

100 V

100 to 240 V

110 to 130 V

110 to 130 V

200 to 240 V

Region

Japan

USA & Canada

Europe & Australia

Insulation Resistance (R

R 1 M /500 V DC

1 M R 12 M /500 V DC

R 10 M /500 V DC

)

Dielectric Strength

AC 1 kV 1 minute

AC 1.5 kV 1 minute

AC 1 kV 1 minute
AC 3 kV 1 minute

AC 1.5 kV 1 minute

(

Class

(

Class

Clearance Distance (d), (d'

d, d' 3 mm

d, d' 4 mm

d, d' 3.2 mm

d 4 m m

)

d' 8 m m (Power cord
d' 6 m m (Primary wire

)

Fig.1-1-11

AC Line Voltage

100 V

110 to 130 V

110 to 130 V

220 to 240 V

Region

Japan

USA & Canada

Europe & Australia

Load Z

1

0.15

1.5

2

50

Leakage Current (i)

i 1 mA rms

i 0.5 mA rms

i 0.7 mA peak
i 2 mA dc

i 0.7 mA peak
i 2 mA dc

a, b, c

Exposed accessible parts

Exposed accessible parts

Antenna earth terminals

Other terminals

Fig.1-1-12

NOTE :

These tables are unofficial and for reference only. Be sure to confirm the precise values for your particular country and locality.

)

)

)

1-4 (No.YD049)

1.2 Hard Disk Drive (HDD) Handling Precautions

The HDD is a precision device for use in reading and writing a large amount of data on or from a disk rotating at a high speed. If it is
not handled carefully, either abnormal operation may result or it may not be possible to read data. The HDD is sensitive to the following
items and special care is required in safeguarding against them when handling an HDD. Also take care in handling a set incorporating
an HDD.

(1) Vibrations and impacts
(2) Static electricity
(3) Rough handling

1.2.1 Handling in transport, etc.

• Be sure to place the HDD in the manufacturer's specified pack­age carton before transport.

• When receiving a package containing an HDD, check that the
package carton is not damaged (such as having holes in the
carton, crushed corners, etc.).

• Do not impact the packaging carton when loading or unloading

HDD
Do not throw or
drop packages.

it.

• It is not permitted to use the inner package carton only for
transporting an HDD.

• Do not stack package cartons one upon another.

Be sure to package and
transport the HDDs correctly.

1.2.2 Handling an HDD in the stand-alone status

• When handling an HDD on a hard workbench, place an anti­static mat (rubber sheet) or similar object on the hard surface
(to prevent any impacts occurring between the HDD and
bench).

• Do not stack the HDDs one upon another.

• Do not knock an HDD with a hard object (such as a screwdriv­er).

• Do not place an HDD on its side panel without using a support
(do not place an HDD in an unstable position).

1.2.3 Handling the installation of an HDD

• Place antistatic mats or similar sheets on all of the surfaces on which work is conducted or when the HDD is transported.

• Do not permit the HDD to knock against the set's brackets.

• When screwing the brackets, be careful not to knock the HDD. When using a power screwdriver, use a low-shock model and arrange
the tightening torque properly.

• When mounting an HDD in a main body, take care not to apply excessive force to the brackets.

(No.YD049)1-5

SECTION 2

SPECIFIC SERVICE INSTRUCTIONS

2.1 Different table of features

The following table indicates main different points between models SR-DVM70AG and SR-DVM70EU.

ITEM SR-DVM70AG SR-DVM70EU

DVD REGIONAL CODE REGION 3 REGION 2

2.2 Service position

This unit has been designed so that the Mechanism and Main
board assemblies can be removed together from the bottom
chassis. Before diagnosing or servicing the circuit boards, take
out the major parts from the bottom chassis.

2.2.1 How to set the "Service position"

(1) Refer to the disassembly procedure and perform the disas-

sembly of the major parts before removing the Mechanism
assembly.

(2) Remove the screws that fix the Mechanism, Main board as-

sembly to the bottom chassis. If any other screws are used
to fix the boards, remove them also.

(3) Remove the combined Mechanism, HDD, DVD unit,

switching regulator, digital, DV jack, junction and Main

board assemblies.
(4) If any other major parts are used, remove them also.
(5) Connect the wires and connectors of the major parts that

have been removed in steps (1) to (4). (Refer to Fig. 2-2a.)
(6) Place the combined Mechanism, Main board and other

board assemblies upside down.
(7) Insert the power cord plug into the power outlet and then

proceed with the diagnostics and servicing of the board as-

sembly.

Notes:

• Before inserting the power cord plug into the power out-

let, make sure that none of the electrical parts are able
to short-circuit between the workbench and the board
assembly.

• For the disassembly procedure of the major parts and

details of the precautions to be taken, see "Removing
the major parts".

• If there are wire connections from the Main board and

Mechanism assemblies to the other major parts, be sure
to remove them (including wires connected to the major
parts) first before performing step (2).

• When carrying out diagnosis and repair of the Main

board assembly in the "Service position", be sure to
ground both the Main board and Mechanism assem­blies. If they are improperly grounded, there may be
noise on the playback picture or FDP counter display
may move even when the mechanism is kept in an inop­erative status.

• In order to diagnose the playback or recording of the

cassette tape, set the Mechanism assembly to the re­quired mode before placing it upside down. If the mech­anism mode is changed (including ejection) while it is in
an upside down position the tape inside may be dam­aged.

• For some models, the mechanism and board assem-

blies are attached by connectors only. When carrying
out a diagnosis or repair of the boards in the "Service
position", make sure that the connectors are not dis­connected.

TP3901

TP3902

TP3906

TP3907

TP3908

TP3903

TP3904

TP3905

SWITCHING
REGULATOR
board assembly

JUNCTION
board assembly

DIGITAL
board
assembly

DV JACK
board
assembly

DVD
UNIT

DISPLAY / SWITCH
board assembly

HDD

Fig.2-2a

REAR JACK
board assembly

MAIN
board
assembly

MDA
board
assembly

DV MAIN
board
assembly

OPERATION / JACK
board assembly

1-6 (No.YD049)

2.3 Jig RCU mode

This unit uses the following two modes for receiving remote con­trol codes.

(1) User RCU mode:Ordinary mode for use by the user.

(2) Jig RCU mode: Mode for use in production and servicing.
When using the Jig RCU, it is required to set the unit to the Jig
RCU mode (the mode in which codes from the Jig RCU can be
received). As both of the above two modes are stored in the EE­PROM, it is required to set the unit back to the User RCU mode
each time that an adjustment is made or to check that the neces­sary operations have been completed.These modes can be set
by the operations described below.

Note:

• When the unit is set to Jig RCU mode and when the unit

is under Jig RCU mode, the remote control unit attached
to product operates only in "Remote Control Code 1".
Since the unit is in "Remote Control Code 3" when it is
shipped and just after its batteries are changed, "Re­mote Control Code 3" needs to be changed to "Remote
Control Code 1."

• Confirm the RCU mode when exchanged parts. Since

some SERVICE PARTS sets the unit to the Jig RCU
mode as initial setting. Therefore please set the unit to
the user RCU mode after replacing the EEPROM.

User RCU mode

Jig RCU mode

2.3.1 Changing Remote Control Code

(1) Slide the TV/CABLE/SAT/DVD switch to DVD.
(2) Press the number key "1" of the remote control unit while

pressing the "SET UP" button of the remote control unit.
Then,press the "ENTER" button, and then release the

"SET UP" button.
(3) Press the "POWER" button on the unit to turn off the unit.
(4) Press the "PLAY" button on the unit for over 5 seconds

while the unit is turned off. The code currently set appears

on the front display panel.
(5) Press the "STOP" button on the remote control to change

the unit’s code. When FDP indicator displays "DVD1," it

means that the Remote Control Code has been changed to

"1."

2.3.2 Setting the Jig RCU mode

(1) Turn on the power.
(2) Press the "DV/HDD/DVD" select button repeatedly on the

unit so that the DVD lamp lights up on the unit.
(3) Press the following remocon keys continuously within 2

seconds " SET UP " → " 2 " → " 8 " → " ENTER ".

When the unit is set to the Jig RCU mode, the symbols

( " : " ) in the time display of the FDP are blinked.

(Refer to Fig.2-3a User/Jig RCU mode)

2.3.3 Setting the User RCU mode

(1) Turn off the power.
(2) Press the "REC" and "PAUSE" buttons of the unit simulta-

neously. Alternatively, transmit the code "43-9D" from the

Jig RCU.

Fig.2-3a User/Jig RCU mode

( blinked)

(No.YD049)1-7

DISASSEMBLY

3.1 Removing the major parts

3.1.1 Destination of connectors

Two kinds of double-arrows in connection tables respectively

show kinds of connector/wires.

: The connector of the side to remove

CONN. No. PIN No.CONNECTOR

WR2a

WR2b

Main CN101

Main CN103

 Destination of connectors

CONN. No. PIN No.CONNECTOR

WR2a

WR2b

WR3a

WR3b

WR4a

WR4b

WR4c

CN7108

(CN1001)

CN7109

(CN1002)

CN7121

(CN1802)

WR5a

WR6a

WR6b

WR6c

WR6d

WR8a

WR8b

WR8c

WR8d

WR8e

WR9a

WR9b

WR11a

WR11b

WR11c

WR11d

WR12a

WR12b

WR12c

WR12d

Main

Main

Junction

Digital

Digital

Digital

Junction

Junction

Junction

Junction

Junction

SW. REG

SW. REG

SW. REG

SW. REG

Junction

Main

Main

Main

Main

Rear jack

Rear jack

DV Main

DV Main

DV Main

DV Main

Main

Main

Main

Main

: Wire: Flat wire : Board to board (B-B)

Digital CN761

Digital CN762

CN3104

CN3102

CN5504

CN2201

CN2101

CN1405

CN5502

CN7108

CN7109

CN7121

CN7126

CN5304

CN5303

CN5301

CN5302

CN7127

CN3103

CN2602

CN701

CN901

CN951

CN952

CN1502

CN4001

CN1501

CN5501

CN5404

CN2601

CN501

CN3104

Operation/jack

Display/switch

DVD unit

DVD unit

HDD

Junction

Digital

Digital

Digital

Digital

DV jack

Junction

HDD

Main

Fun motor

DV Main

Junction

Junction

Junction

Junction

Main

Main

DV mechanism sensor

DV drum motor

DV MDA

Main

DV Main

DV Main

DV Main

DV Main

CN7201

CN7001

CN1406

CN1003

CN1001

CN1002

CN1802

CN4104

CN5501

CN5402

CN2002

CN7102

CN8001

CN7123

CN7107

CN902

FW851

CN5506

CN5403

CN1001

CN3701

CN3501

CN1503

SECTION 3

3.1.2 How to read the procedure table

This table shows the steps for disassembly of the externally fur­nished parts and board assemblies. Reverse these steps when
re-assembling them.

Step/

Loc No.

40

10

15

15

4

40

40

4

6

28

20

14

6

19

4

19

2

6

19

11

4

9

8

3

15

8

20

5

8

8

7

7

[1] Top cover 3-1a

(1) (2) (3) (4) (5)

(1) Order of steps in Procedure

(2) Part name to be removed or installed.
(3) Fig. No. showing procedure or part location.
(4) Identification of part to be removed, unhooked, unlocked,

(5) Adjustment information for installation

3.1.3 Disassembly procedure

Step/

Loc No.

[1]
[2]

[3]

[4]

[5]
[6]

[7]

[8]

[9]
[10]
[11]

[12]

[13]
[14]

Part Name

Bracket 2(S1c)

Fig.

No.

----------------------------------------

Point Note

4(S1a),(S1b),3(L1a), <Note 1a>
2(SD1a),(P1a),(W1a),
CN1(WR1a),

When reassembling, perform the step(s) in the reverse or­der.
These numbers are also used as the identification (loca­tion) No. of parts Figures.

released, unplugged, unclamped or unsoldered.
P= Spring, W= Washer, S= Screw, L= Locking tab, SD=
Solder, CN**(WR**)= Remove the wire (WR**) from the
connector (CN**).

Note:

• The bracketed ( ) WR of the connector symbol are

assigned nos. in priority order and do not corre­spond to those on the spare parts list.

Part Name

Top cover
Front panel assembly
(Operation jack board assembly)
(Display/switch display board assembly)
DVD unit
(Bracket)
Digital board assembly

DV jack board assembly
Switching regulator board assembly

HDD
(Bracket),(Sheet)
Junction board assembly

Rear jack board assembly
Rear cover
DV mechanism assembly

DV main board assembly
(Bracket)

Bracket(DV MAIN)
Main board assembly

Fig.
No.

3-1b
3-1a
3-1b

3-1a
3-1b
3-1a
3-1b

3-1a,3-1b

3-1a
3-1b

3-1a
3-1b
3-1a
3-1b

3-1b
3-1b
3-1a
3-1b

3-1a
3-1b

3-1b

3-1a,3-1b

Point Note

8(S1a)
(S2a),3(L2a),5(L2b)
CN3104(WR2a),CN3102(WR2b

4(S3a),4(S3b)
CN5504(WR3a),CN2201(WR3b)
4(S4a),CN2101(WR4a)
CN1405(WR4b),CN5502(WR4c),
CN7108(CN1001),CN7109(CN1002)
CN7121(CN1802)
(S5a),CN7126(WR5a)
4(S8a)
CN5304(WR6a),CN5303(WR6b),
CN5301(WR6c),CN5302(WR6d)
4(S7a),4(S7b)

(S8a),CN7127(WR8a),
CN3103(WR8b),
CN2602(WR8c),
CN701(WR8d),CN901(WR8e)
3(S9a),CN951(WR9a),CN952(WR9b)
7(S10a),(S10b),3(L10a)
3(S11a),CN1502(WR11a),
CN4001(WR11b),
CN1501(WR11c),CN5501(WR11d)
4(S12a),4(S12b),CN5404(WR12a),
CN2601(WR12b),CN501(WR12c),
CN3104(WR12d)
3(S13a)
3(S14a)

<Note2a>
<Note2b>

)

<Note2a>

<Note2a>

<Note2a>

<Note2a>

<Note2a>

<Note3a>
<Note3b>

1-8 (No.YD049)

< Note 2a >

• Be careful not to damage the connector and wire etc. during
connection and disconnection.

• When connecting the flat wire to the connector, be careful with
the flat wire direction.

< Note 2b >

• When attaching the Front panel assembly, make sure that the
door opener of DV deck is in the down position.

< Note 3a >

• When reattaching the bracket(DV MAIN), secure the screws
(S13a) in the order of 1,2,3.

< Note 3b >

• When reattaching the Main board assembly, secure the
screws (S14a) in the order of 1,2,3.

REAR JACK
BOARD ASSY

MAIN BOARD ASSY

(WR12a)

(WR11d)

<Note2a>

CN5403

CN5404

CN3501

CN1001

CN3701

DV MAIN BOARD ASSY

CN4001

CN5501

CN3104

CN2002

<Note2b>

(WR12b)

<Note2a>

CN2601

CN1503

CN1501

CN5506

CN951

(WR9a)

<Note2a>

(WR12c)

<Note2a>

(WR8d)

CN501

<Note2a>

(WR11c)

<Note2a>

(WR8e)

<Note2a>

CN901

CN902

CN701

D

(WR12d)

<Note2a>

CN3102

(WR6d)

FW851

CN852

(WR9b)

CN5402

(WR8c)

CN2602

CN3014

CN3103

CN5302

(WR6c)

CN5301

<Note2a>

CN7107

CN7123

(WR3a)

CN8001

(WR4c)

CN7102

(WR8b)

DRIVE UNIT

(WR8a)

FAN

CN5001

SWITCHING REGLATOR
BOARD ASSY

(WR6b)

CN5303

(WR6a)

<Note2a>

CN5304

CN5501

JUNCTION BOARD ASSY

CN5502

CN5504

CN1003

(WR3b)

<Note2a>

CN2201

DIGITAL
BOARD ASSY

CN7127

DV JACK BOARD ASSY

CN7106

CN2101

(WR5a)

CN7126

(WR4a)

<Note2a>

CN1405

(WR4b)

<Note2a>

CN4104

Operation/jack board assembly

(WR2a)

<Note2a>

CN7201

NOTE) INSERT FFC WIRE
TO THE CONNECTOR BEFORE
ATTACHING TO FRONT PANEL.

(WR2b)

<Note2a>

CN7001

Fig.3-1a

BOTTOM SIDE

TOP SIDE

Display/switch board assembly

NOTE) WHEN YOU FIX ANY PWB
WITH THE SCREW,

PUT IT ON THE JIGS.

(No.YD049)1-9

(S1a)

(S1a)

(S1a)

[1]Top cover

(S1a)

[13]Bracket(DV MAIN)

(S13a)

[12]Bracket

(S13a)

1

3

(S12a)

(S12b)

(S1a)

(S1a)

[9]Rear jack board assembly

[11]DV mechanism assembly

(S11a)

u

j

CN4001

CN1502

[12]DV main board assembly

2

(S12b)

(S12b)

(S12a)

<Note2a>

(S13a)

(S1a)

(S1a)

[10]Rear cover

(L10a)

(S11a)

(WR11a)

(S11a)

(WR11b)

<Note2a>

(S3a)

(S10a)

(L10a)

(S9a)

(S10a)

(S10b)

(S10a)

(L10a)

[3]DVD unit

(S3a)

[3]Bracket

(S3a)

[14]Main board assembly

Bottom chassis

[2]Front panel

assembly

(L2a)

(L2b)

(L2b)

(L2a)

(S14a)

1

(L2b)

j

3

(S2a)

(S14a)

2

(S14a)

[5]DV jack board assembly

c

[4]Digital board assembly

[6]Switching regulator

board assembly

[7]HDD

(S5a)

(S4a)

(S8a)

(S3b)

(S6a)

(S6a)

CN5302

CN5001

(S7a)

(S7b)

(S7a)

(S4a)

(S7b)

(S4a)

[8]Junction board assemly

(S3a)

(S3b)

(S6a)

[7]Bracket(HDD)

(S7b)

(S7a)

[7]SHEET

1-10 (No.YD049)

Fig.3-1b

SECTION 4

ADJUSTMENT

4.1 Before adjustment

4.1.1 Precautions

(1) Observe the specified screw tightening torque when

attaching parts. The torque should be 0.04 Nm (0.4 kgfcm)
unless otherwise specified.

(2) Always disconnect the power supply unit before proceed-

ing to solder or attach parts.

(3) When plugging or unplugging a wire, be careful not to

damage the connector.

(4) When replacing a part, be careful not to damage other

parts or to mistakenly attach parts.

4.1.2 Tools required for adjustments

TORQUE DRIVER

12

YTU94088

Tool for replacing tip IC

4

PTS40844-2

BIT

YTU94088-003

Tool for installing slit washer

3

YTU94121A

Table 4-1-1

4.1.3 Disassembly and assembly procedures

The following table shows the steps for assembling or disassem­bling the mechanism parts. Read the following descriptions care­fully before actual assembly/disassembly operations.

(1) : Order of disassembly steps. Reverse this order when as-

sembling.

(2) : Name of the disassembled/assembled part.

Surface where the disassembled/assembled part is

(3) :

mounted. T = Top. B: Bottom.

(4) : Number of disassembly drawing.

(5) : Parts to be removed in disassembly/assembly, such as

screws, washers and springs, and the points.

Symbol Name & Point

SScrew

W Washer

PSpring

* Connector, lock(L), soldering(SD),

shield, etc.

[Example] • (W1) = Remove the washer W1.

• (P1) = Remove the spring P1.

(6) : Notes for disassembly/assembly.
(7) : For the phase alignment in disassembly/assembly and

the parts which require phase adjustments after assembly,
see "4.7 Mechanism phase check/adjustment".

4.1.4 Screws and washers used in disassembly/assembly

of the mechanism assembly

Table 4-1-2 shows the symbols and part numbers of the screws
and washers used in the mechanism assembly.
When disassembling or assembling the mechanism assem­bly,be sure to attach screws and washers correctly by referring
to the following table.

Symbol Part number

(S1) QYSDSP2005ZA

(S2) YQ43893

(S3) YQ43893-7

Symbol Part number

(W1) YQ44246

(W2) YQ44246-3

Table 4-1-2

Step/Loc No. Fig. No. Point Note Discription

1

2

3

4

[A] Cassette housing assembly/
[B] Mechanism assembly

[1]Drum assembly

[2]Motor bracket assembly

[3]Middle catcher assembly

Part Name

1

2

2

3

2(S1),(L1) (L5)

3(S2)

4(S2)

3(S2)

T

T

T

T

1

2,3

2,4

(1) (2) (3) (4) (5) (6) (7)

(No.YD049)1-11

4.2 Disassembly/assembly of the mechanism assembly

4.2.1 Introduction

The disassembly and assembly of the mechanism assembly should usually be performed in the ASSEMBLY mode.(Table 4-2-1)
Note that the mechanism is in the cassette in (C-IN) mode when the mechanism assembly is taken out of the set and that the C-IN
mode should be switched to the ASSEMBLY mode in this case.
To set the ASSEMBLY mode, apply 3 V DC to the electrodes on the upper part of the loading motor as shown in Fig. 4-2-7.

MODE

PARTS

[1]

ROTARY
ENCORDER

R. ENC -20

MAIN CAM GEAR 0

[2]

[3]

36

C-IN

ASSEMBLY

17

S. FF

30.33

36.33

87

0

15

33.33

40

LOADING END

169.66

166.66

140

PLAY REV STOP FF/REW

270.33

276.33

223.66

226.66

185

229.66

273.33

220

303.66

306.66

245

190.33

193.33

160

196.33

Table 4-2-1

4.2.2 Mechanism modes

The mechanism has 6 modes as shown in Table 4-3-1. The current mode can be confirmed by the positioning of the " " marking on
the sub-cam gear and the " " marking on the mechanism. See the following figures (Figs. 4-2-1 to -6) for details.

Note:

• This mechanism assembly has another ASSEMBLY mode. However, this mode cannot be identified from the markings because
it corresponds to an intermediate position between the C-IN ( C ) mode and S-FF ( H ) mode. This mode can be confirmed by the
rotary encoder phase. See Fig. 4-2-7.

1. Checking the mechanism mode

Fig.4-2-1

Fig.4-2-4

1-12 (No.YD049)

[H]

[H][C]

Fig.4-2-2

Fig.4-2-5

[P]

Fig.4-2-3

[F][S][R]

Fig.4-2-6

2. Setting/checking the ASSEMBLY mode

Wire (Brown)

DC 3 V

Motor bracket assembly (Loading Motor)

Marking

(Colored red)

Rotary encoder

< ASSEMBLY >

Wire (Red)

[C]

[H]

Fig.4-2-7

(No.YD049)1-13

4.3 Mechanism timing chart

See following table (Table 4-3-1).

MODE

PARTS

36

[1]

ROTARY
ENCODER

[2]

[3]

ROTARY ENCODER

MAIN CAM 0

SUB CAM

POLE BASE

CTL PLATE

FF/REW

MAIN BRAKE(SUP)

MAIN BRAKE(TU)

SUB BRAKE

ON(REV MODE PRESS UP)

ON(PLAY MODE)

PINCH ROLLER

EXIT GUIDE ARM

HALF LOADING

TENSION ARM

BAND ARM PLATE

CLUTCH LOCK

SUP CENTRRING

OFF

S/REV

PLAY

ON 1

ON 2

OFF

ON 1

ON 2

OFF

OFF

OFF

ASSY

OFF

OFF 1

OFF 2

OFF

OFF 1

OFF 2

ASSEMBLY

C-IN

17

-20

0

15

0

ON

ON

ON

ON

ON

S. FF

30.33

33.33

40

4015

36.33

87

LOADING END

169.66

166.66

140

140

PLAY REV STOP FF/REW

270.33

276.33

223.66

226.66

185

185

229.66

273.33

220

220

303.66

306.66

245

245

190.33

193.33

160

160

196.33

CENTERRING ARM

1-14 (No.YD049)

S/REV

Table 4-3-1