Output PowerAt stereo operationFront channels130 W per channel, min. RMS, driven into 6
At surround operationFront channels130 W per channel, min. RMS, driven into 6
Center channel130 W, min. RMS, driven into 6
Surround channels130 W per channel, min. RMS, driven into 6
Surround back channels130 W per channel, min. RMS, driven into 6
AudioAudio Input Sensitivity/
VideoVideo Input Sensitivity/
HDMIHDMI Input (Ver. 1.1)VCR (DBS), DVR/DVD
Tuning Range87.50 MHz to 108.00 MHz
Usable SensitivityMonaural12.8 dBf (1.2
50 dB Quieting Sensitivity Monaural16.0 dBf (1.7
Stereo Separation at REC OUT35 dB at 1 kHz
Tuning Range531 kHz to 1 710 kHz
Power RequirementsAC 240 V , 50 Hz
Power Consumption180 W (at operation)
Dimensions (W
Mass7.8 kg
USB WIRELESS SYSTEMThe USB wireless transmitter supplied with this receiver supports
× H × D)435 mm × 91.5 mm × 371 mm
Impedance
Audio Input (DIGITAL IN) Coaxial:
Audio Output LevelDVR, VCR300mV
Signal-to-Noise Ratio ('66 IHF/'78 IHF)80 dB/62 dB
Frequency Response (6
Bass Boost+4 dB ±1 dB at 100 Hz
Equalization
(at DSP operation)
Impedance
Video Output Level/
Impedance
SynchronizationNegative
HDMI Output (Ver. 1.0)MONITOR OUT
Stereo37.5 dBf (20.5
DVR/DVD, VCR, DBS, TV300 mV/47 k
DIGITAL IN 1(DVR/DVD)
Optical:
DIGITAL IN 2(DBS), 3(VCR)
USBUSB WIRELESS
Ω)20 Hz to 20 kHz (±1 dB)
Center frequency63 Hz, 250 Hz, 1 kHz, 4kHz, 16 kHz
Control range±8 dB
Composite video:
DVR/DVD, VCR, DBS
S-video:
DVR/DVD, VCR, DBS
Component:
DVR/DVD, VCR (DBS)
Composite video:
DVR, VCR, MONITOR OUT
S-video:
DVR, VCR, MONITOR OUT
Component:
MONITOR OUT
FM tuner (IHF)
AM tuner
General
more than 0.8% total harmonic distortion (IEC268-3/DIN).
more than 0.8% total harmonic distortion.
Ω at 1 kHz, with no more than
0.8% total harmonic distortion.
more than 0.8% total harmonic distortion.
more than 0.8% total harmonic distortion.
Ω
0.5 V(p-p)/75Ω
-21 dBm to -15 dBm (660 nm ±30 nm)
USB TERMINAL
1 V(p-p)/75
Y (luminance): 1 V(p-p)/75 Ω
C (chrominance, burst): 0.3 V(p-p)/75 Ω
Y (luminance): 1 V(p-p)/75 Ω
PB, PR: 0.7 V(p-p)/75 Ω
1 V(p-p)/75 Ω
Y (luminance): 1 V(p-p)/75 Ω
C (chrominance, burst): 0.3 V(p-p)/75 Ω
Y (luminance): 1 V(p-p)/75 Ω
PB, PR: 0.7 V(p-p)/75 Ω
Ω
µV/75 Ω)
µV/75 Ω)
µV/75 Ω)
5.0 W (in standby mode)
Direct Sequence Spreading Spectrum (DSSS) using 2.4 GHz
frequency band.
Designs and specifications are subject to change without notice.
Ω at 1 kHz with no
Ω at 1 kHz with no
Ω at 1 kHz, with no
Ω at 1 kHz, with no
1-2 (No.MB500)
SECTION 1
PRECAUTIONS
1.1Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purposes. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety characteristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
(No.MB500)1-3
1.5 Safety Precautions (U.K only)
(1) This design of this product contains special hardware and many circuits and components specially for safety purposes. For con-
tinued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits.
(2) Any unauthorised design alterations or additions will void the manufacturer's guarantee; furthermore the manufacturer cannot
accept responsibility for personal injury or property damage resulting therefrom.
(3) Essential safety critical components are identified by ( ) on the Parts List and by shading on the schematics, and must never
be replaced by parts other than those listed in the manual. Please note however that many electrical and mechanical parts in
the product have special safety related characteristics. These characteristics are often not evident from visual inspection. Parts
other than specified by the manufacturer may not have the same safety characteristics as the recommended replacement parts
shown in the Parts List of the Service Manual and may create shock, fire, or other hazards.
(4) The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be separated from live parts,
high temperature parts, moving parts and/or sharp edges for the prevention of electric shock and fire hazard. When service is
required, the original lead routing and dress should be observed, and it should be confirmed that they have been returned to
normal, after re-assembling.
1.5.1 Warning
(1) Service should be performed by qualified personnel only.
(2) This equipment has been designed and manufactured to meet international safety standards.
(3) It is the legal responsibility of the repairer to ensure that these safety standards are maintained.
(4) Repairs must be made in accordance with the relevant safety standards.
(5) It is essential that safety critical components are replaced by approved parts.
(6) If mains voltage selector is provided, check setting for local voltage.
Burrs formed during molding may be left over on some parts of the chassis. Therefore,
pay attention to such burrs in the case of preforming repair of this system.
1-4 (No.MB500)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
(No.MB500)1-5
SECTION 3
DISASSEMBLY
3.1Main body section
3.1.1 Removing the top cover
(See Fig.1 and 2)
(1) From the both sides of the main body, remove the four
screws A attaching the top cover. (See fig. 1)
(2) From the back side of the main body, remove the five
screws B and screw C attaching the top cover. (See Fig. 2)
Reference:
When removing the screw C, use a screwdriver to show
as follows.
TORX Driver: size T10
Parts number: DR-L70
(3) Remove the top cover in the direction of the arrow. (See
Fig. 1)
Top cover
A
Fig.1
3.1.2 Removing the USB wireless board
(See Fig. 3)
• Remove the top cover.
(1) From the top side of the main body, disconnect the LAN
module board from USB board.
(2) Remove the two screws D attaching the USB board.
(3) Disconnect the connector wire from connector CN662
the DSP board.
of
B
C
Top cover
BB
Fig.2
DSP board
USB wireless board
1-6 (No.MB500)
CN662
Rear panel
Coaxial connector
Fig.3
D
3.1.3 Removing the fan motor
(See Fig. 4)
• Remove the top cover.
(1) Remove the tie band bundling the wires.
(2) From the top side of the main body, disconnect the wire
from the connector CN103
(3) Remove the three screws E and take out the fan motor as-
sembly.
(4) Remove the two screws F attaching the fan motor to the fan
bracket.
on the main amplifier board.
Fan motor assembly
Fan motor
F
Main amplifier board
CN103
3.1.4 Removing the HDMI board
(See Figs.5 and 6)
• Remove the top cover.
(1) From the back side of the main body, remove the three
screws G attaching the HDMI board to the rear panel. (See
Fig.5)
(2) From the top side of the main body, remove the screw H at-
taching the HDMI board. (See Fig.6)
(3) Disconnect the card wires from the connectors (CN731
CN732, and CN762) on the HDMI board. (See Fig.6)
(4) Disconnect the parallel wire from the connector CN711 on
the HDMI board. (See Fig.6)
(5) Take out the HDMI board from the main body. (See Fig.6)
3.1.5 Removing the DSP board
(See Figs.5 and 6)
• Remove the top cover and fan motor.
(1) From the back side of the main body, remove the five
screws J attaching the DSP board to the rear panel. (See
Fig.5)
(2) From the top side of the main body, remove the screw K at-
taching the DSP board. (See Fig.6)
(3) Disconnect the connector CN681
the DSP connect board. (See Fig.6)
Note:
When removing the DSP board, take care not to break
the claw of the connector on it.
(4) Take out the DSP board and disconnect the wires from the
connectors (CN661
side of the DSP board. (See Fig.6)
(5) Disconnect the card wires from the connectors (CN651
CN652
) on the DSP board. (See Fig.6)
(6) Take out the DSP board from the main body.
, CN682, and CN683) on the forward
on the DSP board from
F
E
Fan bracket
E
Fig.4
G
,
Rear panel
J
Fig.5
CN652
DSP board
K
CN683
CN682
CN661
CN732
CN731
,
CN771
CN762
HDMI board
H
CN681
CN651
Fig.6
(No.MB500)1-7
3.1.6 Removing the SCART board
(See Fig.7 and 8)
• Remove the top cove, USB board, DSP board and HDMI
board.
(1) Remove the six screws L attaching the SCART board.
(See Fig.7)
(2) Disconnect the card wire from CN537
SCART board. (See Fig.8)
and CN539 of the
LL L
Fig.7
3.1.7 Removing the input board
(See Fig.9 and 10)
(1) Remove the seven screws M attaching the input
board.(See Fig.9)
(2) Remove the three screws N attaching the input board. (See
Fig.10)
(3) Disconnect the each wire from each connector of the input
board.
CN539
SCART board
M
Input board
CN537
Fig.8
Fig.9
3.2Other item
For the other items, please refer to RX-D701S,RX-D702B No.MB441.
1-8 (No.MB500)
N
Fig.10
SECTION 4
ADJUSTMENT
This service manual does not describe ADJUSTMENT.
SECTION 5
TROUBLESHOOTING
This service manual does not describe TROUBLESHOOTING.
(No.MB500)1-9
Victor Company of Japan, Limited
Audio/Video Systems Category 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan
(No.MB500)
Printed in Japan
VPT
SCHEMATIC DIAGRAMS
AUDIO/VIDEO CONTROL RECEIVER
RX-D701SB,RX-D701SE,RX-D701SEN
RX-D702BB,RX-D702BE,RX-D702BEN
CD-ROM No.SML200601
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Contents
Block diagrams
Standard schematic diagrams
Printed circuit boards
COPYRIGHT 2006 Victor Company of Japan, Limited.
2-1
2-2
2-15 to 21
No.MB500SCH
2006/1
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the
parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "
mark nearby are critical for safety.
Block diagram
Audio/Video signal input,system control and component section
J ;U.S.A.
C ;CANADA
B ;U.K.
E ;CONTINENTAL EUROPE
EN:NORDIC COUNTRIES
EV;EAST EUROPEAN COUNTRIES
US;SINGAPORE
UJ;U.S. ARMY
A ;AUSTRARIA
UT;TAIWAN
UF;CHINA
D :JAPAN
QMF51W2-5R0-J8
QMF5AE2-R10-J1
FC113
QNG0020-001Z
F104
!
FC104
QNG0020-001Z
FC114
QNG0020-001Z
1
D1001
1SS133-T2
QMF51W2-2R5-J8 QMF51W2-2R5-J8
QMF5AE2-R10-J1 QMF5AE2-R10-J1
C1001
4700p
2143
!
!
RY101
QSK0142-001
FC103
QNG0020-001Z
!
!
C1002
0.22
Q1001
KRC105S-X
R1002
3.3M
C1003
0.001
PW104
PW103
!
CN120
LIVE/
BRN
2
1
123
NEUTRAL/
BLU
MAINS
PLUG
!
C1004
0.001
!
QGA7901C1-02
QNZ0136-001Z
EP151
!
LVA10579-5
VOLTAGE SELECTOR LOCATION
746
3
8
5
2
746
1
3
5
2
746
3
1
528
220V230-240V127V110V
VOLTAGE MEASUREMENT CONDITION
POWER ON
SOURCE FM(NO SIGNAL)
SURROUND OFF
VOLUME 0
746
1
3
1
8
528
1
2
3
4
(SHEET 3/18)
to CN101 of LVA10578-1
AC
AC
RY+9V
POWER_ON
FW121
54
!
FC114
QNG0020-001Z
9
1
T102
!
QQT0478-002
F104
!
QNG0020-001Z
!
QNG0020-001Z
FC104
3
4
1SS133-T2
FC113
D1001
FC103
F103
!
QNG0020-001Z
!
!
C1001
!
4700p
2
!
RY101
QSK0128-001
1
R1002
3.3M
C1002
!
0.22
!
C1003
0.001
Q1001
KRC105S-X
PW103
PW104
!
CN120
LIVE/
BRN
2
1
NEUTRAL/
BLU
MAINS
PLUG
Parts are safety assurance parts.
When replacing those parts make
123
sure to use the specified one.
!
QGA7901C1-02
!
C1004
0.001
EP151
QNZ0136-001Z
LVA10579-5
2-2
Regulator / DC-DC converter section
LVA10578-1
D+5V_Mi
1
DGND
2
FL1
3
VPP
4
FL2
5
CN102
QGF1205C1-05
to CN902
of LVA10579-1
R110
100k
C114
1/50
*MARK LIST
R1164
R1151
R1152
R1153
C102
R101
R102
R104
R105
D105
B2017
Q173
C172
C1149
C1150
C1167
C1168
C1139
C1140
C1141
Fuse
F101
F102
B,E,EN,EV,US,A,
J,C
UF,UT,UJ,D
51k47k
1.5k
2.2k
1.8k
3.6k
1.2k
1.8k
US,A,UF,
J,C,B,E,EN,EV
UT,UJ
220/631000/25
USENONE
USENONE
USENONE
USENONE
USE
USE
J,C,D,
US,A,UF,UT,UJ
NONE
NONE
NONE
NONE
J,C,D
NONE
NONE
NONE
J,C,D
QMF51U1-4R0-J8
QMF51U1-4R0-J8
C169
470/16
LVA10578-6
BLK_REG2
LVA10578-4
D+5V_DSP
BLK_REG
USENONE
USENONE
NONE
NONE
B,E,EN,EV
USE
USE
USE
USE
B,E,EN,EV,
US,A,UF,UT,UJ
USE
USE
USE
B,E,EN,EV,US,A,
UF,UT,UJ
QMF51W2-4R0-J8
QMF51W2-4R0-J8
!
Q176
2SD2394/EF/
Q177
2SD2394/EF/
!
C166
470/16
R177
100
R178
100
2SD2394/EF/
C168
100/16
D+5V_HDMI
!
Q171
DCDC_+12
DCDC_-B+12
Q156
2SC1740S/RS/-T
PRI_RY+12V
!
Q172
2SD2394/EF/
R172
100
R171
100
D159
MTZJ6.2C-T2
2SD2394/EF/
C165
100/16
to CN530
of LVA10599-1
of LVA10600-1
1
2
CN130
3
4
5
6
7
8
9
10
11
1
2
3
4
5
6
7
8
9
1
2
R189
R188
R187
R186
C167
0.0022
*
Q173
Q155
2SC1740S/RS/-T
!
2SD2394/EF/
C174
10/50
D171
MTZJ13B-T2
!
2SD2394/EF/
C176
10/50
MTZJ13B-T2
+12V_RY
HP_RY
+7V
-7V
AGND
A+5V_DSP
A+5V_Vi
A+9V_Vi_Tu
+12V_RY
AC_DET_2
VCHANGE_1
VCHANGE_2
HP_RY
DGND
D+5V_DSP
D+5V_Mi
B+5V_Mi
FAN_ON/OFF
FAN_LOW
POWER_ON
REG_DET
D+5V_HDMI
CN131
to CN531
of LVA10599-1
of LVA10600-1
CN103
QGA2501C1-02
R16710UNF
!
!
CN107
CN117
QGA2001F1-03
D158
MTZJ7.5A-T2
Q174
R174
10k
Q175
D172
FAN
FANGND
10
10
10
10
1W
R168
2.2k
!
UNF
!
1W
UNF
!
1W
UNF
!
1W
UNF
!
1W
UNF
1/4W
123
123
*
C172
0.0047
!
R165
UNF
0.22
(1W)
C164
2200p
R166
!
2.2k
(1/4W)
R173
UNF
!
4.7
(1/2W)
UNF
(1/2W)
C173
1/50
R175
UNF
4.7
(1/2W)
!
!
R176
UNF
10k
(1/2W)
C175
1/50
MTZJ8.2C-T2
to CN104
of LVA10578-1
CN114
QGA2001F1-07
UNF
+12V
+B
PGND
-B+12V
-B
CN115
to CN105
of LVA10578-1
Q103
KTC3200/GL/-T
D117
!
D161 1A3G-T1
!
D162
1A3G-T1
7
6
5
4
3
2
1
1
2
3
4
5
FW323
1
2
3
4
to CN313
7
6
5
4
3
2
1
1
2
3
4
5
R109
22k
+7V
AGND
-7V
of LVA10578-2
CN104
CN105
QGA2001C1-05
M_CLOCK
123
4
CN101
QGA2001C1-04
AC
AC
from FW121
of LVA10579-5
RY+9V
POWER_ON
PGND
AMP_+B
AMP_-B
TH_COM
!
R105
10
UNF
(1/4W)
!
UNF
(1/4W)
UNF
(1/4W)
UNF
R102
3.3k
(1W)
*
R101
15k
*
C102
*
D105
*
MTZJ12C-T2
C101
0.0047/100
D102
1A3G-T1
!
!
!
D104
1A3G-T1
D101
1A3G-T1
1A3G-T1
R272
NI
TH272
EP102
QNZ0136-001Z
NI
!
D103
R1111
Q1104
KTA1268/GL/-T
1k
DCDC Converter
2W
2W
UNF
UNF
!!
2.2k
2.2k
R1109
R1110
R1112
1k
C1165
D1111
1SS133-T2
R1113
39k
R1118
47k
NI
C1119
C1139
C1140
*
*
0.1/100
NI
C1166
C1141
C1120
0.1/100
*
L1101
22
QQL78AK-220
C1117
4700/63
C1118
4700/63
L1102
22
QQL78AK-220
R1105
C1115
0.1/100
C1108
R1107
C1112
!
R1108
C1114
R1106
!
C1116
0.1/100
0.0033
LVA10579-11
DCDC Converter_Control
D1154
R11701kR1169
BLK_DCCTRL
UDZS2.7B-X
3.3k
VCC
1CLR1D1CLK
IC115
SN74HC74ANS-X
891011121314
D1155
1SS133-T2
2PRE
2CLK
1PRE1Q1Q
2Q
C1158
0.1
GND2Q
7654321
R1166
470
C1156
100p
1SS133-T2
2D
2CLR
Q1103
KTA1268/GL/-T
R1114
820
C1157
0.1
VCC
D1153
SN74HC00ANS-X
R1165
3.3k
D1105
(1W)(1W)(1W)(1W)
10
C1107
0.0033
10
0.0033
10
0.0033
10
C1109
C1110
891011121314
7654321
0.0033
C1111
C1113
0.0033
GND
D
S
0.0033
0.0033
D
S
Q1101
2SK3599-01MR
(With H.Sink)
!
!
D1107
FMB-G19L
(With H.Sink)
!
D1108
FMB-G19L
(With H.Sink)
Q1102
2SK3599-01MR
(With H.Sink)
!
G
G
N.I.
R1103
33
R1117
4.7
1/4W
D1106
N.I.
R1104
33
1/4W
SSS_ON/OFF
1/4W
IRS2011S-X
C1155
1
D1110
1SS133-T2
!
IC101
R1162
IC112
NJM2403M-X
C1122
0.33
SSS_ON/OFF
1k
R1161
1M
1
(1/2)
7
IC112
NJM2403M-X
PWM_V
PWM_V
8
R1101
NI
NI
C1143
0.22/100
C1142
0.22/100
C1161
C1162
D1109
1SS133-T2
C1123
NI
+12V
FEEDBACK
+12V
FEEDBACK
R1180
Q1173
1
R1115
820
CN152
QGB2510J1-12
123456789
123456789
CN151
QGB2510K1-12
D1151
1SS133-T2
13k
KTA1504/YG/-X
C1174
100/16
KIA7805API
R1158
680
R1176
47k
100k
EP101
QNZ0136-001Z
R1102
100k
NI
NI
C1144
0.22/100
C1145
0.22/100
C1163
!
IC121
C1182
100/16
D1174
1SS133-T2
Q1172
C1164
C1153
1
NJM2125F-X
KRC102S-X
R1175
C1106
6800/80
!
C1171
4.7/50
DRIVER_SD
123
C1181
0.01
IC111
5
+
1
C1151
47/16
-
4
3
2
R1156
120k
C1152
1
R1157
10k
C1159
820p
R1179
10k
R1174
D1173
1SS133-T2
Q1177
Q1171
C1173
0.01
C1172
KTC3875/YG/-X
1000p
2.2k
R1116
4.7
1/4W
1234
VB
HO
VS
HIN
PGND
101112
101112
PGND
4
(2/2)
M_CLOCK
M_CLOCK
+
3
-
2
+
5
-
6
LIN
VCHANGE_2
VCHANGE_2
R1164
C1154
100p
COM
VCHANGE_1
DRIVER_SD
DRIVER_SD
VCHANGE_1
*
D1152
1SS133-T2IC113
AC_DET_2
AC_DET_2
VCCLO
8765
Vout_DET
Vout_DET
C1126
AC_DET_1
AC_DET_1
R1159
10k
R1160
1k
330
R1163
C1105
R1171
3.3k
UNF
1/4W
3.3k
NI
6800/80
R1181
47k
1
D1101
!
30PRA20-FC
!
D1103
30PRA20-FC
C1124
0.1/250
C1146
0.1/250
C1167
*
0.1/250
C1168
*
0.1/250
C1150
*
0.1/250
C1149
*
0.1/250
C1147
0.1/250
C1125
0.1/250
D1102
!
30PRA20-FC
!
D1104
30PRA20-FC
1SS133-T2
R1155
22k
C1104
0.22
C1137
0.1/250
C1138
0.1/250
C1148
NI
D1171
R1154
3.3k
R1173
10k
D1172
1SS133-T2
C1136
0.1/250
C1135
0.1/250
C1103
0.22
*
R1153
R1172
3.3k
Q1174
KTC3875/YG/-X
C1101
0.22/100
C1133
0.22/100
C1134
0.22/100
CN111
QGA3901C1-03
3
from CN211
of LVA10579-13
2
1
C1102
0.22/100
C1131
0.22/100
C1132
0.22/100
*
*
R1151
R1152
Q1152
Q1151
KRC102S-X
KRC102S-X
R1178
100
Q1176
NI
Q1175
NI
!
!
MY
F102
!
C111
100/63
S2S3S3
FC102
FC112
Q163
Q161
Q162
COM
QNG0020-001Z
QNG0020-001Z
!
D115
1A3G-T1
KRC111S-X
KRC111S-X
470/16
!
F101
!
D114
1A3G-T1
R183
R184
R182
NI
+12V_FAN
Q154
KRC102S-X
A+5V_Vi
C161
C163
470/16
1234567
CN106
S2
QGA3901C1-08
from CN206
of LVA10579-13
FC101
QNG0020-001Z
!
FC111
QNG0020-001Z
C110
220/50
D113
1A3G-T1
!
A+5V_DSP
2k
47k
A+9V_Vi_Tu
R154
10k
R155
11k
D154
MTZJ8.2A-T2
2k
R159
R160
47k
!
2SD2394/EF/
(With H.Sink)
**
R104
10
UNF
(1/4W)
*
B2017
Q101
6800/25
3300/25
KTD863/Y/-T
D107
D108
1A3G-T1
1A3G-T1
!!
D106
MTZJ6.2B-T2
C104
470/16
C151
C152
C106
0.1/100
D119
UF304G-F82
D109
!
NI
C105
0.1/100
NI
D120
D111
D110
UF304G-F82
!
!
10DDA20-FD
D112
C107
!
IC151
KIA7805API
IC152
KIA7809API
1SS133-T2
C157
10/50
IC153
KIA7805API
!
(With H.Sink)
0.1/100
(With H.Sink)
123
!
(With H.Sink)
123
(With H.Sink)
D152
KRA102S-X
(With H.Sink)
123
MTZJ8.2C-T2
D157
MTZJ8.2C-T2
Q158
KTA1046/Y/
R152 4.7
!
Q151
D156
!
10DDA20-FD
C153
0.01
C155
0.01
Q152
KRC102S-X
C158
0.01
R15122UNF
!
R153
!
R156
R157
R158
!
R161
!
!
!
!
UNF
0.47
!
10
(1/4W)
!
(1/4W)
470
4.7
(1/4W)
4.7
R162
2.2k
R164
2.2k
R16310UNF
1W
(1/4W)
(1/4W)
(1/4W)
(1/4W)
UNF
1W
UNF
UNF
UNF
1W
UNF
UNF
UNF
TH101
4.7
!
!
C154
100/16
C156
100/25
!
Q153
2SD2394/EF/
D153
MTZJ13B-T2
!
C159
100/16
Q157
C160
100/16
C162
100/16
R103
6.8
UNF
(1/4W)
C103
R106
820
4700p
!
8
1/4W
R107
5.6 UNF
!
MY
C109
C108
0.047
0.047
!
Q102
KTA1046/Y/
!
R108
C113
3.3k
22/50
UNF
(1/4W)
C112
22/50
D116
MTZJ36C-T2
R181
100
KRC111S-X
+7V
-7V
Parts are safety assurance parts.
When replacing those parts make
sure to use the specified one.