JVC RX-7001PGD User Manual

AUDIO/VIDEO CONTROL RECEIVER
RECEPTOR DE CONTROL DE AUDIO/VÍDEO RECEPTOR DE COMANDO AUDIO/VÍDEO
RX-7001PGD
TV/CATV/DBS
ANALOG/DIGITAL
123
TEST REAR-L
456
EFFECT REAR-R
7
/P
89
SEA MODE
10
0
RETURN
SET
CHANNEL VOLUMETV VOL
TAPE/MD
VCR
CONTROL
PLAY
/REW
TUNING STOP PAUSE
REC
RM-SRX7001P REMOTE CONTROL
CENTER
ENTERENTER
SUBWOOFER
VCR
SLEEP
MENUMENU
+10
100+FM MODE
AUDIO/
TV/VCR
CATV/DBS
TEXT DISPLAY
MUTING
FF/
RX-7001P AUDIO/VIDEO CONTROL RECEIVER
STANDBY
STANDBY/ON
PHONES
COMPULINK
Remote
SPEAKERS
12
SURROUND ON/OFF
DSP MODE
BALANCE/SURROUND
ADJUST
SEA MODE
ANALOG/DIGITAL
SEA ADJUST SETTING
THEATER LIVE CLUB DANCE CLUB HALL PAVILION
INPUT
FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY FM MODE
SOUND SELECT
BASS BOOST ONE TOUCH OPERATION
SOURCE NAME
INPUT ATT.
MULTI JOG
DIGITAL
DVD
TV SOUND/DBS PHONO
SOURCE SELECTOR
CD
TAPE/MDVCR
FM
AM
MASTER VOLUME
+
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
SURROUND
ON/OFF
SURROUND
MODE
CD-DISC
SOUND
MENU
EXIT
TV/VIDEO
DOWN UP
DIGITAL
INSTRUCTIONS
MANUAL DE INSTRUCCIONES
INSTRUÇÕES
For Customer Use:
Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.
Model No. Serial No.
LVT0396-008A
Warnings, Cautions and Others / Avisos, precauciones y otras notas / Advertêcias, precauções e outras notas /
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
PRECAUCIÓN
Para reducir riesgos de choques eléctricos, incendio, etc.:
1. No extraiga los tornillos, los cubiertas ni la caja.
2. No exponga este aparato a la lluvia o a la humedad.
ATENÇÃO
Para reduzir riscos de choques eléctricos, incêndio, etc.:
1. Não retire parafusos nem desmonte as tampas ou o gabinete.
2. Não exponha este aparelho à chuva nem à umidade.
Caution –– STANDBY/ON switch!
Disconnect the mains plug to shut the power off completely. The STANDBY/ON switch in any position does not disconnect the mains line. The power can be remote controlled.
Precaución –– Interruptor STANDBY/ON !
Desconectar el cable de alimentación para desactivar la alimentación totalmente. Cualquier que sea la posición de ajuste del interruptor STANDBY/ON , la alimentación no es cortada completamente. La alimentación puede ser controlada remotamente.
Precaução –– Interruptor STANDBY/ON !
Desconectar o cabo de alimentação para desligar a alimentação por completo. Qualquer que seja a posição de ajuste do interruptor STANDBY/ON , a alimentação não é completamente cortada. A alimentação pode ser controlada remotamente.
G-1
Caution: Proper Ventilation
To avoide risk of electric shock and fire and to protect from damage. Locate the apparatus as follows: Front: No obstructions open spacing. Sides: No obstructions in 10 cm from the sides. Top: No obstructions in 10 cm from the top. Back: No obstructions in 15 cm from the back Bottom: No obstructions, place on the level surface. In addition, maintain the best possible air circulation as illustrated.
Precaución: Ventilación Adecuada
Para evitar el riesgo de choque eléctrico e incendio y para proteger el aparato contra daños. Ubique el aparato de la siguiente manera: Frente: Espacio abierto sin obstrucciones Lados: 10 cm sin obstrucciones a los lados Parte superior: 10 cm sin obstrucciones en la parte superior Parte trasera: 15 cm sin obstrucciones en la parte trasera Fondo: Sin obstrucciones, colóquelo sobre una superficie
nivelada Además, mantenga la mejor circulación de aire posible como se ilustra.
Precaução: ventilação apropriada
Para prevenir o risco de choque elétrico ou incêndio e para proteger o aparelho contra danos. Localize-o da seguinte maneira: Frente: Espaço aberto, sem obstruções Lados: Espaço de 10 cm sem obstruções nos lados Topo: Espaço de 10 cm sem obstruções acima Atrás: Espaço de 15 cm sem obstruções atrás Parte inferior: Sem obstruções. Coloque o aparelho em superfície
nivelada. Mantenha, além disso, a maior circulação de ar possível, como indica a ilustração.
EnglishPortuguês
Español
Wall or obstructions Pared u obstrucciones Parede ou obstáculo
Spacing 15 cm or more Espacio de 15 cm o más Espaço de 15 cm ou mais
RX-7001PGD
Floor Piso Piso
Front Frente Frente
Stand height 15 cm or more Allura del soporte 15 cm o más Base com altura de 15 cm ou mais
G-2

Table of Contents

Parts Identification ...................................... 2
English
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Setting the Voltage Selector Switch ........................................... 3
Connecting the FM and AM Antennas....................................... 3
Connecting the Speakers ............................................................ 4
Connecting Audio/Video Components....................................... 5
Connecting the Power Cord ....................................................... 9
Putting Batteries in the Remote Control .................................... 9
Basic Operations ....................................... 10
Turning the Power On and Off (Standby) ................................ 10
Selecting the Source to Play..................................................... 10
Adjusting the Volume ............................................................... 11
Selecting the Front Speakers .................................................... 11
Muting the Sound ..................................................................... 12
Reinforcing the Bass ................................................................ 12
Attenuating the Input Signal .................................................... 12
Adjusting the Subwoofer Output Level.................................... 12
Basic Settings ........................................... 13
Recording a Source .................................................................. 13
Adjusting the Front Speaker Output Balance........................... 13
Changing the Source Name...................................................... 13
Setting the Subwoofer Information .......................................... 14
Setting the Speakers for the DSP Modes ................................. 14
Digital Input (DIGITAL IN) Terminal Setting ......................... 16
Selecting the Analog or Digital Input Mode ............................ 16
Showing the Text Information on the Display ......................... 17
Setting the AM Tuner Interval Spacing.................................... 17
Storing the Basic Settings and Adjustments — One Touch
Operation ........................................................................... 17
Using the Sleep Timer.............................................................. 17
Using the DSP Modes ................................ 21
Available DSP Modes According to the Speaker Arrangement .. 23
Adjusting the 3D-PHONIC Modes .......................................... 24
Adjusting the DAP Modes ....................................................... 24
Adjusting the Surround Modes ................................................ 25
Activating the DSP Modes....................................................... 27
Using the DVD MULTI Playback Mode .......... 29
Activating the DVD MULTI Playback Mode .......................... 29
Using the On-Screen Menus ........................ 30
Selecting the Source to Play..................................................... 30
Selecting Different Sources for Picture and Sound.................. 30
Activating the DSP Modes....................................................... 30
Selecting the Analog or Digital Input Mode .............................. 30
Adjusting the Front Speaker Output Balance........................... 31
Reinforcing the Bass ................................................................ 31
Attenuating the Input Signal .................................................... 31
Adjusting the Subwoofer Output Level.................................... 31
Adjusting the DSP Modes ........................................................ 31
Adjusting the DVD MULTI Playback Mode ........................... 32
Selecting Your Favorite SEA Mode ......................................... 32
Creating Your Own SEA Mode ................................................ 32
Setting the Basic Setting Items ................................................ 33
Operating the Tuner.................................................................. 33
Storing the Preset Stations ....................................................... 34
Assigning Names to Preset Stations......................................... 34
COMPU LINK Remote Control System ......... 35
TEXT COMPU LINK Remote Control System .. 36
Showing the Disc Information on the TV Screen .................... 37
Searching for a Disc (Only for the CD player) ........................ 38
Entering the Disc Information.................................................. 39
Receiving Radio Broadcasts ........................ 18
Tuning in Stations Manually .................................................... 18
Using Preset T uning ................................................................. 18
Selecting the FM Reception Mode........................................... 19
Assigning Names to Preset Stations......................................... 19
Using the SEA Modes ................................ 20
Selecting Your Favorite SEA Mode ........................................... 20
Creating Your Own SEA Mode ................................................ 20
AV COMPU LINK Remote Control System .... 41
Operating JVC’s Audio/Video Components ... 43
Operating Audio Components .................................................. 43
Operating Video Components .................................................. 45
Operating Other Manufacturers’ Video
Equipment ............................................ 46
Troubleshooting ......................................... 52
Specifications ............................................ 53
1

Parts Identification

Become familiar with the buttons and controls on the receiver before use. Refer to the pages in parentheses for details.
1
2
345 67 8 9 p
English
1
2
3 4
5 6
7
8
9
STANDBY
STANDBY/ON
PHONES
COMPULINK
Remote
AUDIO/VIDEO CONTROL RECEIVERRX-7001P
SPEAKERS
12
TV/CATV/DBS
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
ANALOG/DIGITAL
SURROUND
ON/OFF
SURROUND
MODE
CD-DISC
SOUND
MENU
EXIT
TV/VIDEO
/REW
DOWN UP
REC
RM-SRX7001P REMOTE CONTROL
CENTER
123
MENUMENU
TEST REAR-L
456
ENTERENTER
EFFECT REAR-R
/P
89
7
SUBWOOFER
SEA MODE
10
0
RETURN FM MODE
SET
CHANNEL VOLUMETV VOL
TAPE/MD
VCR
CONTROL
FF/
PLAY
TUNING
STOP PAUSE
VCR
SLEEP
+10
100+
AUDIO/ TV/VCR
CATV/DBS
TEXT
DISPLAY
MUTING
SURROUND ON/OFF
DSP MODE
BALANCE/SURROUND
ADJUST
p q
w
e
r
t
y
u
i
o
INPUT
ANALOG/DIGITAL
SEA MODE
SEA ADJUST SETTING
THEATER LIVE CLUB DANCE CLUB HALL PAVILION
FM/AM TUNING TUNER PRESET
TUNER/SEA MEMORY
SOUND SELECT
INPUT ATT.
FM MODE
BASS BOOST ONE T O UCH OPERATION
SOURCE NAME
MULTI JOG
Remote Control
1 TV/CATV/DBS button (45, 46) 2 Source selecting buttons (10)
DVD, DVD MULTI, CD, TAPE/MD, TV/DBS, PHONO, FM/AM, VCR
3 SURROUND ON/OFF button (25, 27) 4 SURROUND MODE button (25, 26) 5 CD-DISC button (44) 6 SOUND button (20, 24, 29) 7 On-screen operation buttons (30, 37)
MENU, SET, EXIT, %, fi, @, #
8 TV VOL +/– buttons (45, 46) 9 Operating buttons for audio/video components
(43 – 47)
p AUDIO buttons q VCR w SLEEP button (17) e ANALOG/DIGIT AL button (16) r • 10 keys for selecting preset channels (19)
• 10 keys for adjusting sound (20, 24 – 27, 29)
• 10 keys for operating audio/video components (43 – 47)
t Remote control mode selector (10, 43, 46) y TEXT DISPLAY button (37) u CHANNEL +/– buttons (45 – 47) i VOLUME +/– buttons (11) o MUTING button (12)
, (10)
button (45, 47)
DIGITAL
DVD
TV SOUND/DBS PHONO
TAPE/MDVCR
SOURCE SELECTOR
CD
FM
AM
MASTER VOLUME
+
dsa;oiuytrewq
Front Panel
1 STANDBY/ON button and STANDBY
lamp (10)
2 Remote sensor (9) 3 SURROUND ON/OFF button and lamp (26, 27) 4 SEA MODE button (20) 5 INPUT ANALOG/DIGITAL button (16) 6 FM/AM TUNING button (18)* 7 FM MODE button (19) 8 Display (10) 9 Source lamps (10) p MASTER VOLUME control (11) q PHONES jack (12) w SPEAKERS 1/2 buttons and lamps (11) e DSP MODE button (24) r BALANCE/SURROUND ADJUST button
(12, 13, 24)*
t SEA ADJUST button (20)* y SETTING button (14 – 17)* u TUNER/SEA MEMORY button (18 – 20) i SOUND SELECT/INPUT ATT. button
(11, 12)
o BASS BOOST/SOURCE NAME button
(12, 13)
; ONE TOUCH OPERATION button and lamp
(17)
a TUNER PRESET button (19)* s MULTI JOG control
What this control actually does depends on which function you are trying to adjust. Before using this control, select the function by pressing one of the buttons marked with *.
d SOURCE SELECTOR control (10)
2

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.
English
Before Installation
General
• Be sure your hands are dry.
• Turn the power off to all components.
• Read the manuals supplied with the components you are going to connect.
Locations
• Install the receiver in a location that is level and protected from moisture.
• The temperature around the receiver must be between –5˚C and 35˚C (23˚F and 95˚F).
• Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.
Handling the receiver
• Do not insert any metal object into the receiver.
• Do not disassemble the receiver or remove screws, covers, or cabinet.
• Do not expose the receiver to rain or moisture.
Connecting the FM and AM Antennas
FM Antenna Connections
A
ANTENNA
ANTENNA
AM
LOOP
FM 75 COAXIAL
L
IA
FM 75
X
A
O
C
AM EXT
FM Antenna
Extend the supplied FM antenna horizontally.
B
AM
LOOP
ANTENNA
FM 75
O
C
L
IA
X
A
AM EXT
Checking the Supplied Accessories
Check to be sure you have all of the following items, which are supplied with the receiver. The number in the parentheses indicates quantity of the pieces supplied.
• Remote Control (1)
• Batteries (2)
• AM Loop Antenna (1)
• FM Antenna (1)
• AC Plug Adaptor (1)
If anything is missing, contact your dealer immediately.
Setting the Voltage Selector Switch
Before connections, always do the following first if necessary.
Set the correct voltage for your area with the voltage selector switch on the rear panel. Use a screw driver to rotate the switch so the number the arrow is pointing at is the same as the voltage where you are plugging in the receiver.
AM
LOOP
AM
EXT
Outdoor FM Antenna Cable
A. Using the Supplied FM Antenna
The FM antenna provided can be connected to the FM 75 COAXIAL terminal as temporary measure.
B. Using the Standard Type Connector (Not Supplied)
A standard type connector should be connected to the FM 75
COAXIAL terminal.
Note:
If reception is poor, connect the outdoor antenna. Before attaching a 75 going to an outdoor antenna), disconnect the supplied FM antenna.
coaxial cable (the kind with a round wire
3
VOLTAGE SELECTOR
110V
220V
127V
230 - 240V
Voltage Mark
AM Antenna Connections
+
–+–
RIGHT LEFT
1
2
1
2
FRONT SPEAKERS
ANTENNA
FM 75 COAXIAL
Snap the tabs on the loop into the slots of the base to assemble the AM loop.
Basic connecting procedure
1
2
1
R
I
G
H
T
3
4
1
R
I
G
H
T
1
R
I
G
H
T
English
AM
LOOP
AM
EXT
1
AM Loop Antenna
2
3
Outdoor single vinyl-covered wire (not supplied)
Turn the loop until you have the best reception.
Notes:
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. This could cause poor reception.
• If reception is poor, connect an outdoor single vinyl-covered wire to the AM EXT terminal. (Keep the AM loop antenna connected.)
1 Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2 Turn the knob counterclockwise.
3 Insert the speaker signal cable.
4 Turn the knob clockwise.
Connecting the front speakers
You can connect two pairs of front speakers (one pair to the FRONT SPEAKERS 1 terminals, and another pair to the FRONT SPEAKERS 2 terminals).
Right speaker
FRONT SPEAKERS 1
Left speaker
Connecting the Speakers
You can connect the following speakers:
• Two pairs of front speakers to produce normal stereo sound.
• One pair of rear speakers to enjoy the surround effect.
• One center speaker to produce more effective surround effect (to
emphasize human voices).
• One subwoofer to enhance the bass.
IMPORTANT:
After connecting the speakers listed above, set the speaker setting information properly to obtain the best possible DSP effect. For details, see page 14.
For each speaker (except for a subwoofer), connect the (–) and (+) terminals on the rear panel to the (–) and (+) terminals marked on the speakers. For connecting a subwoofer, see page 5.
CAUTION:
Use speakers with the SPEAKER IMPEDANCE indicated by the speaker terminals.
Right speaker
FRONT SPEAKERS 2
Left speaker
4
About the speaker impedance
English
The required speaker impedance of the front speakers does differ depending on whether both the FRONT SPEAKERS 1 and FRONT SPEAKERS 2 terminals are used or only one of them is used.
CASE 1 When you connect only one set of front speakers
Front
speaker
1
speaker
Front
1
Connecting the subwoofer speaker
You can enhance the bass by connecting a subwoofer. Connect the input jack of a powered subwoofer to the SUBWOOFER OUT jack on the rear panel, using a cable with RCA pin plugs (not supplied).
SUBWOOFER
OUT
Powered subwoofer
Connecting Audio/Video Components
Use front speakers with 8 – 16 impedance.
CASE 2 When you connect two sets of front speakers
Front
speaker
2
Front
speaker
1
Front
speaker
2
Front
speaker
1
Use front speakers 16 – 32 impedance.
Connecting the rear and center speakers
Connect rear speakers to the REAR SPEAKERS terminals and a center speaker to the CENTER SPEAKER terminals.
You can connect the following audio/video components to this receiver. Refer also to the manuals supplied with your components.
Audio Components Video Components
• Turntable • DVD player*
• CD player* • TV*
• Cassette deck • DBS tuner* or MD recorder* • VCR
*
You can connect these components using the methods described in “Analog connections” (below) or in “Digital connections” (see page
8).
Analog connections
Audio component connections
Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, and the red plug to the audio right jack.
CAUTION:
If you connect a sound-enhancing device such as a graphic equalizer between the source components and this receiver, the sound output through this receiver may be distorted.
1
Left rear
speaker
5
Center speaker
Right rear
speaker
CENTER
SPEAKER
+
2
REAR
SPEAKERS
RIGHT LEFT
Turntable
If an earth cable is provided for your turntable, connect the cable to the screw marked (H) on the rear panel.
Turntable
RIGHT LEFT
+
To audio output
AUDIO
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
Note:
Any turntables incorporating a small-output cartridge such as an MC (moving-coil) type must be connected to this receiver through a commercial head amplifier or step-up transformer. Direct connection may result in insufficient volume.
CD player
CD player
To audio output
Cassette deck or MD recorder
Cassette deck
To audio input
RIGHT LEFT
MD recorder
To audio output
AUDIO
PHONO
CD
OUT
(REC)
TAPE
/MD
IN
(PLAY)
RIGHT LEFT
AUDIO
PHONO
CD
OUT
(REC) TAPE
/MD
IN
(PLAY)
Video component connections
Use the cables with RCA pin plugs (not supplied). Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack. If your video components have S-video (Y/C-separation) terminals, connect them using S-video cables (not supplied). Connecting these video components through the S-video input/output terminals will give you better picture playback (or recording) quality.
IMPORTANT:
This receiver is equipped with both the composite video and S-video input/output terminals for connecting video components. You do not have to connect both the composite video and S-video terminals. However, remember that the video signals from the composite
video input terminals are output only through the composite video output terminals, while the ones from the S-video input terminals are output only through the S-video output terminals.
Therefore, if a recording video component and a playing video component are connected to the receiver through the different video terminals, you cannot record the picture from the playing component on the recording component. In addition, if the TV and a playing video component are connected to the receiver through the different video terminals, you cannot view the playback picture from the playing component on the TV .
VCR
A
S-VHS (or VHS) VCR
DC
English
To audio input
To audio output
Note:
You can connect either a cassette deck or an MD recorder to the TAPE/MD jacks. When connecting an MD recorder to the TAPE/MD jacks, change the source name, which will be shown on the display when selected as the source, to “MD.” See page 13 for details.
If your audio components have a COMPU LINK-3 or TEXT COMPU LINK jack
• See also page 35 for detailed information about the connection and the COMPU LINK-3 remote control system.
• See also page 36 for detailed information about the connection and the TEXT COMPU LINK remote control system.
B
AUDIO
DVD
TV SOUND
/DBS
OUT
(REC)
VCR
IN
(PLAY)
Å To left/right channel audio output ı To left/right channel audio input Ç To S-video output Î To composite video outputTo composite video input Ï To S-video input
VIDEO
VIDEO S-VIDEORIGHT LEFT
F
E
6
English
DVD
VIDEO
VIDEO S-VIDEORIGHT LEFT
AUDIO
DVD
A
B
C
To audio output
TV and/or DBS tuner
When connecting the TV, DO NOT connect the TV’s video output to these video input terminals.
RIGHT
AUDIO
TV SOUND
/DBS
TV
(REC)
IN
(PLAY)
MONITOR
OUT
OUT
DVD
VCR
DVD player
• When you connect the DVD player with stereo output jacks:
DVD player
VIDEO
VIDEO S-VIDEORIGHT LEFT
Å To front left/right channel audio output (or to audio mixed
output if necessary)
ı To S-video output Ç To composite video output
Connect the TV to the MONITOR OUT jack to view the playback picture from the other connected video components.
To composite video input
To S-video input
Note:
Use a TV of the PAL- or multi-color system.
RIGHT
AUDIO
To audio output
DBS tuner
DBS
To composite video output
To S-video output
DVD
TV SOUND
/DBS
OUT
(REC)
IN
(PLAY)
OUT
(REC) VCR 2
IN
• When you connect the DVD player with its analog discrete output (5.1 CH reproduction) jacks:
A
B
AUDIO
VIDEO
VIDEO S-VIDEORIGHT LEFT
SUB
WOOFER
CENTER
DVD
DVD player
DVD
ED
DVD
TV SOUND
/DBS
OUT
(REC) VCR
IN
(PLAY)
VIDEO
VIDEO S-VIDEORIGHT LEFT
C
F
Å To center channel audio output ı To subwoofer audio output Ç To S-video output Î To front left/right channel audio outputTo rear left/right channel audio output Ï To composite video output
Note:
When connecting the DBS tuner to the TV SOUND/DBS jacks, change the source name, which will be shown on the display when selected as the source, to “DBS.” See page 13 for details.
7
Digital connections
This receiver is equipped with three DIGITAL IN terminals — one digital coaxial terminal and two digital optical terminals, and one DIGITAL OUT terminal. You can connect any digital equipment such as —
• DBS tuner,
• Digital TV broadcast tuner,
• DVD player,
• CD player,
• and MD recorder.
IMPORTANT:
• When connecting the DVD player, digital TV broadcast tuner or DBS tuner using the digital terminals, you also need to connect it to the video jack (either composite video terminal or S-video terminal) on the rear. Without connecting it to the video jack, you can view no playback picture.
• After connecting the components using the DIGITAL IN terminals, set the following correctly if necessary. – Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Digital Input (DIGITAL IN) Terminal Setting” on page
16.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 16.
Digital input terminals
Notes:
• When shipped from the factory, the DIGITAL IN terminals have been set for use with the following components. – DIGITAL 1 (coaxial): For DVD player – DIGITAL 2 (optical): For CD player – DIGITAL 3 (optical): For digital TV broadcast tuner
• When you want to operate the CD player or MD recorder using the COMPU LINK remote control system, connect the target component also as described in “Analog connections” (see pages 5 and 6).
• When you want to operate the DVD player using the AV COMPU LINK remote control system, connect the DVD player also as described in “Analog connections” (see page 7).
Digital output terminal
MD recorder, etc.
Digital optical cable (not supplied) between digital optical terminals
English
DBS
CD player
Digital coaxial cable (not supplied) between digital coaxial terminals
Digital optical cable (not supplied) between digital optical terminals
When the component has a digital coaxial output terminal, connect it to the DIGITAL 1 (DVD) terminal, using the digital coaxial cable (not supplied).
When the component has a digital optical output terminal, connect it to the DIGITAL 2 (CD), or DIGITAL 3 (TV) terminal, using the digital optical cable (not supplied).
DVD playerDBS tuner
DVD
MD recorder
DIGITAL IN
PCM / DOLBY DIGITAL
DIGITAL 1 (DVD)
DIGITAL 2 (CD)
MPEG/ DTS
When the digital recording equipment such as an MD recorder has a digital optical input terminal, connecting it to the DIGITAL OUT terminal enables you to perform digital-to-digital recording.
DIGITAL OUT
PCM/DOLBY DIGITAL/MPEG/DTS
Before connecting a digital optical cable, unplug the protective plug.
DIGITAL 3 (TV)
8
English
Connecting the Power Cord
Before plugging the receiver into an AC outlet, make sure that all connections have been made.
Plug the power cord into an AC outlet.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first. When using the remote control, aim the remote control directly at the remote sensor on the receiver.
Keep the power cord away from the connecting cables and the antenna. The power cord may cause noise or screen interference. We recommend that you use a coaxial cable to connect the antenna, since it is well-shielded against interference.
Notes:
• The preset settings such as preset channels and sound adjustment may be erased in a few days in the following cases:
–When you unplug the power cord. –When a power failure occurs.
• If the wall outlet does not match the AC plug, use the supplied AC plug adaptor.
CAUTIONS:
• Do not plug in before setting the voltage selector switch on the rear of the unit and all connection procedures are complete.
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When unplugging the cord, always grasp the plug so as not to damage the cord.
1
2
R6P(SUM-3)/AA(15F)
3
9
1. On the back of the remote control, remove the battery cover.
2. Insert batteries. Make sure to match the polarity: (+) to (+).
3. Replace the cover.
If the range or effectiveness of the remote control decreases, replace the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity: (+) to (+).
• Use the correct type of batteries. Batteries that look similar may differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.

Basic Operations

The following operations are commonly used when you play any sound source.
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to “AUDIO/TV/ VCR.”
AUDIO/ TV/VCR
CATV/DBS
Turning the Power On and Off (Standby)
On the front panel:
To turn on the power, press STANDBY/ON
. The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.
Current source name appears
Current volume level is shown here
To turn off the power (into standby mode),
press STANDBY/ON again. The STANDBY lamp lights up. A small amount of power is consumed in standby mode. To turn the power off completely, unplug the AC power cord.
From the remote control:
To turn on the power, press AUDIO . The STANDBY lamp goes off. The name of the current source (or station frequency) appears on the display.
To turn off the power (into standby mode),
press AUDIO . The STANDBY lamp lights up.
STANDBY
STANDBY/ON
STANDBY
STANDBY/ON
From the remote control:
Press one of the source selecting buttons.
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
Selected source name appears
DVD Select the DVD player. DVD MUL TI Select the DVD player for viewing the digital video
disc using the analog discrete output mode (5.1CH reproduction) on the DVD player.
To enjoy the DVD MULTI playback, see page 29.
CD* Select the CD player. TAPE/MD* Select the cassette deck (or the MD recorder). TV/DBS Select TV sounds (or the DBS tuner). PHONO* Select the turntable. FM/AM* Select an FM or AM broadcast.
• Each time you press the button, the band alternates between FM and AM.
VCR Select the video component connected to the VCR
jacks.
Notes:
• When connecting an MD recorder (to the TAPE/MD jacks), and a DBS tuner (to the TV SOUND/DBS jacks), change the source name shown on the display. For details, see page 13.
• When you press one of the source selecting buttons on the remote control marked above with an asterisk (*), the receiver automatically turns on.
English
Selecting the Source to Play
On the front panel:
Turn SOURCE SELECTOR until the source name you want appears on the display.
• As you turn the selector, the source changes as follows:
CD O PHONO O TAPE (or MD) O FM O AM O DVD O DVD MULTI O TV SOUND (or DBS) O VCR O (back to the beginning)
The selected source lamp also lights up.
• The DVD lamp lights up both for “DVD” and “DVD MULTI.”
SOURCE SELECTOR
DVD
TV SOUND/DBS PHONO
CD
TAPE/MDVCR
FM
AM
10
Signal and speaker indicators on the display
• The signal indicators light up to indicate the incoming channel
English
signals. – Only the indicators for the incoming signals light up.
• The frame of the signal indicator (except for “LFE” and “S”)
lights up if the corresponding speaker is set to “LARGE” or “SMALL” (for subwoofer, “YES”). – The frames of “L” and “R” indicators always light up.
C
L
R
LFESUBWFR
Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER VOLUME clockwise. To decrease the volume, turn it counterclockwise.
• When you turn MASTER VOLUME rapidly, the volume level also changes rapidly.
• When you turn MASTER VOLUME slowly, the volume level also chang es slowly.
MASTER VOLUME
+
LS
S
RS
L:•When digital input is selected: Lights up when the left
channel signal comes in.
When analog input is selected: Always lights up.
R:•When digital input is selected: Lights up when the right
channel signal comes in.
When analog input is selected: Always lights up.
C: Lights up when the center channel signal comes in. LS: Lights up when the left rear channel signal comes in. RS: Lights up when the right rear channel signal comes in. S: Lights up when the monaural rear channel signal comes in. LFE: Lights up when the LFE channel signal comes in.
Notes:
• When “SUBWOOFER” is set to “YES,”
• When you select “DVD MULTI,” all the signal indicators except “S” light up.
SUBWFR
lights up.
Selecting different sources for picture and sound
You can watch picture from a video component while listening to sound from another component.
On the front panel:
1. Press SOUND SELECT (INPUT
ATT.) briefly while viewing the picture from a video component
SOUND SELECT
INPUT ATT.
such as the VCR or DVD player, etc.
“SOUND SELECT” appears on the display.
From the remote control:
To increase the volume, press VOLUME +.
VOLUME
To decrease the volume, press VOLUME –.
CAUTION:
Always set the volume to the minimum before starting any source. If the volume is set at its high level, the sudden blast of sound energy can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range of “0” (minimum) to “90” (maximum).
Selecting the Front Speakers
On the front panel ONLY:
When you have connected two pairs of the front speakers, you can select which to use.
Press SPEAKERS 1 or SPEAKERS 2 to select the speaker to use.
• Each time you press the button, the lamp on the respective button turns on and off. When the lamp on either button lights up, the respective speakers are activated.
Note:
If you use any of the DSP modes other than the 3D-PHONIC modes with both front speakers activated, the speakers connected to the FRONT SPEAKERS 2 terminals are deactivated.
SPEAKERS
1
2
2. Turn SOURCE SELECTOR to
SOURCE SELECTOR
select the sound (except the TV sound), while the indication of the above step is still on the display.
From the remote control:
Press one of the audio source selecting buttons (CD, TAPE/MD, PHONO, FM/AM, TV/DBS*), while viewing the picture from a video component such as the VCR or DVD player, etc.
Notes:
• Once you have selected a video source, pictures of the selected source are sent to the TV until you select another video source.
*
The TV/DBS button only works for selecting “DBS” as the source but not for selecting “TV SOUND.” When you use the DBS tuner, change the source name correctly (see page 13).
11
Listening only with headphones
You can listen with the headphones without deactivating both pairs of speakers; however, if you want to use the HEADPHONE mode (see below), you must turn off both pairs of speakers.
1. Connect a pair of headphones to the PHONES jack on the front
panel.
2. Press SPEAKERS 1 and/or 2 so that no lamps on the buttons are
turned on. This cancels the surround mode or DSP mode currently selected, and activates the HEADPHONE mode (see below).
• The HEAD PHONE indicator lights up on the display.
HEADPHONE mode:
This mode can reproduce the LFE channel signals, mixing them with the front channel signals. So you will not miss the subwoofer sounds even if you listen to a source using the headphones.
Notes:
• While in the HEADPHONE mode, you cannot use any other DSP modes (see page 21.)
• Activating the speaker cancels the headphones mode and turns on the DSP mode previously selected.
CAUTION:
Be sure to turn down the volume before connecting or putting on headphones, as high volume can damage both the headphones and your hearing.
Attenuating the Input Signal
When the input level of the playing source is too high, the sounds will be distorted. If this happens, you need to attenuate the input signal level to prevent the sound distortion.
On the front panel ONLY:
Press and hold INPUT ATT. (SOUND
SOUND SELECT
SELECT) so that the ATT indicator lights up on the display.
INPUT ATT.
• Each time you press and hold the button, the Input Attenuator mode turns on (“INPUT ATT ON”) or off (“INPUT NORMAL”).
Notes:
• This function is available only for the sources connected using the
analog terminals.
• This function takes effect when the DSP mode is in use.
• When selecting “DVD MULTI” as the source, this effect does not
work.
Adjusting the Subwoofer Output Level
You can adjust the subwoofer output level if you have selected “YES” for the “SUBWOOFER” (see page 14). Once it has been adjusted, the receiver memorizes the adjustment.
English
Muting the Sound
From the remote control ONLY:
Press MUTING to mute the sound through all
MUTING
speakers and headphones connected.
“MUTING” appears on the display and the volume turns off (the volume level indicator goes off).
To restore the sound, press MUTING again so that “OFF” appears on the display.
• Turning MASTER VOLUME on the front panel or pressing VOLUME +/– on the remote control also restores the sound.
Reinforcing the Bass
You can boost the bass level.
On the front panel ONLY:
Press BASS BOOST (SOURCE NAME) briefly to select the bass boost function.
• Each time you press the button, the bass boost function turns on (“BASSBOOST ON”) and off (“BASSBOOST OFF”). – Select “BASSBOOST ON” to activate the bass boost function.
The BASS BOOST indicator lights up on the display.
– Select “BASSBOOST OFF” to cancel it.
The indicator goes off.
BASS BOOST
SOURCE NAME
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
• When the front speakers are all deactivated, the subwoofer level cannot be adjusted.
On the front panel:
1. Press (BALANCE/) SURROUND
BALANCE/SURROUND
ADJUST
ADJUST repeatedly until “SUBWFR LEVEL” appears on the display.
The display changes to show the current setting.
2. Turn MULTI JOG to adjust the
MULTI JOG
subwoofer output level (–10 dB to +10 dB).
From the remote control:
1. Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
2. Press SUBWOOFER –/+ to adjust
the subwoofer output level (–10 dB to +10 dB).
SUBWOOFER
0
+10
100+FM MODE
Note:
This function affects the front speaker sounds only.
12

Basic Settings

Some of the following settings are required after connecting and positioning your speakers in your listening room, while others will make operations easier.
English
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to “AUDIO/TV/ VCR.”
AUDIO/ TV/VCR
CATV/DBS
2. Turn MULTI JOG to adjust the
balance.
• Turning it clockwise decreases the left channel output.
• Turning it counterclockwise decreases the right channel output.
MULTI JOG
Recording a Source
For analog-to-analog recording
You can record any analog source through the receiver to —
• the cassette deck (or MD recorder) connected to the TAPE/MD jacks, and
• the VCR connected to the VCR jacks
— at the same time.
For digital-to-digital recording
You can record the currently selected digital input through the receiver to a digital recording device connected to the DIGITAL OUT terminal.
Notes:
• Analog-to-digital and digital-to-analog recordings are not possible.
• The output volume level, bass boost (see page 12), SEA modes
(see page 20), and DSP modes (see page 21) cannot affect the recording.
• The test tone signal (see page 25, 26) does not come out through
the DIGITAL OUT terminal.
Adjusting the Front Speaker Output Balance
If the sounds you hear from the front right and left speakers are unequal, you can adjust the speaker output balance.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press BALANCE (/SURROUND)
ADJUST repeatedly until “L/R
BALANCE/SURROUND
ADJUST
BALANCE” appears on the display.
The display changes to show the current setting.
Changing the Source Name
When you have connected an MD recorder to the TAPE/MD jacks or the DBS tuner to the TV SOUND/DBS jacks on the rear panel, change the source name which will be shown on the display when you select the MD recorder or DBS tuner as the source.
On the front panel ONLY:
1. When changing the source name
SOURCE SELECTOR
from “TAPE” to “MD”:
Turn SOURCE SELECTOR until “TAPE” appears.
When changing the source name from “TV SOUND” to “DBS”:
Turn SOURCE SELECTOR until “TV SOUND” appears.
2. Press and hold SOURCE NAME (BASS BOOST) until “ASSGN. MD” or “ASSGN. DBS” appears
BASS BOOST
SOURCE NAME
on the display.
To change the source name to “TAPE” or “TV SOUND,” repeat
the same procedure above — in step 1, select “MD” or “DBS” then press and hold SOURCE NAME (BASS BOOST).
Note:
Without changing the source name, you can still use the connected components. However, there may be some inconvenience. – “TAPE” or “TV SOUND” will appear on the display when you select
the MD recorder or DBS tuner. – You cannot use the digital input (see page 16) for the MD recorder. – You cannot use the COMPU LINK remote control system (see page
35) to operate the MD recorder.
13
Setting the Subwoofer Information
Register whether or not you have connected a subwoofer.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
SETTING
1. Press SETTING repeatedly until
“SUBWOOFER” appears on the display.
The display changes to show the current setting.
MULTI JOG
2. Turn MULTI JOG to register
whether you have connected a subwoofer or not.
• As you turn it, the subwoofer setting alternates between “YES” and “NO.”
YES: Select this when a subwoofer is used.
up on the display (see page 11).
NO: Select this when no subwoofer is used.
SUBWFR
lights
Setting the Speakers for the DSP Modes
To obtain the best possible surround sound of the DSP modes, you have to register the information about the speakers arrangement after all connections are completed.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers.
• When you change your speakers, you need to register the information about the speakers again.
On the front panel ONLY:
1. Press SETTING repeatedly until
SETTING
“FRONT SPK” (Front Speaker), “CENTER SPK” (Center Speaker) or “REAR SPK” (Rear Speaker) appears on the display.
The display changes to show the current setting.
MULTI JOG
2. Turn MULTI JOG to select the
appropriate item about the speaker selected in the above step.
• As you turn it, the display changes to show the following:
LARGE SMALL NONE
LARGE: Select this when the speaker size is relatively large. SMALL: Select this when the speaker size is relatively small. NONE: Select this when you have not connected a speaker.
(Not selectable for the front speakers.)
3. Repeat steps 1 and 2 to select the appropriate items for the other speakers.
Notes:
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 12 cm, select “LARGE,” and if it is smaller than 12 cm, select “SMALL. ”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
Center Delay Time Setting
Register the delay time of the sound from the center speaker, comparing to that of the sound from the front speakers. If the distance from your listening point to the center speaker is equal to that to the front speakers, select 0 msec. As the distance to the center speaker becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
• When shipped from the factory, delay time is set to 0 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
SETTING
“CENTER DELAY” appears on the display.
The display changes to show the current setting.
MULTI JOG
2. Turn MULTI JOG to select the delay time of the center speaker output.
• Turn it clockwise to increase the delay time from 0 msec (“C.
DELAY: 0ms”) to 5 msec (“C. DELAY: 5ms”).
• Turn it counterclockwise to decrease the delay time from
5 msec (“C. DELAY: 5ms”) to 0 msec (“C. DELAY: 0ms”).
Notes:
• Center delay time setting is not valid for the DVD MULTI playback
mode.
• You cannot adjust the center delay time when you have set
“CENTER SPK” to “NONE.”
Rear Delay Time Setting
Register the delay time of the sound from the rear speakers, comparing to that of the sound from the front speakers. If the distance from your listening point to the rear speakers is equal to that to the front speakers, select 0 msec. As the distance to the rear speakers becomes shorter, increase the delay time.
• 1 msec increase (or decrease) in delay time corresponds to 30 cm
decrease (or increase) in distance.
• Rear delay time for Dolby Digital, DTS Digital Surround and
MPEG Multichannel is to be set to 5 msec.
• When shipped from the factory, delay time is set to 5 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
SETTING
“REAR DELAY” appears on the display.
The display changes to show the current setting.
English
14
2. Turn MULTI JOG to select the
English
delay time of the rear speaker output.
• Turn it clockwise to increase the delay time from 0 msec (“R. DELAY: 0ms”) to 15 msec (“R. DELAY: 15ms”).
• Turn it counterclockwise to decrease the delay time from 15 msec (“R. DELAY: 15ms”) to 0 msec (“R. DELAY: 0ms”).
Notes:
• Rear delay time setting is not valid for the DVD MULTI playback mode.
• You cannot adjust the rear delay time when you have set “REAR SPK” to “NONE.”
Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if you have used a small speaker for any of the front, center, and rear channels, this receiver automatically reallocate the bass elements, originally assigned to the channel for which you have connected the small speaker, to another channel (for which you have connected the large speaker). To use this function properly, you need to set the crossover frequency level according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers (see page 14), this
function is set to “OFF” and cannot be adjusted.
On the front panel ONLY:
1. Press SETTING repeatedly until
“CROSSOVER FRQ” (Crossover Frequency) appears on the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select the
crossover frequency level according to the size of the small speaker connected.
• As you turn it, the display changes to show the following:
80Hz 100Hz 120Hz
• Use the following comments as reference when adjusting.
80Hz: Select this when the cone speaker unit built in the
speaker is about 12 cm.
100Hz: Select this when the cone speaker unit built in the
speaker is about 10 cm.
120Hz: Select this when the cone speaker unit built in the
speaker is about 8 cm.
Note:
Crossover frequency setting is not valid for the DVD MULTI playback mode, 3D-PHONIC mode, and HEADPHONE mode.
MULTI JOG
SETTING
MULTI JOG
Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using Dolby Digital, DTS Digital Surround or MPEG Multichannel follow the procedure below.
On the front panel ONLY:
1. Press SETTING repeatedly until
SETTING
“LFE ATT” (Low Frequency Effect Attenuator) appears on the display.
The display changes to show the current setting.
MULTI JOG
2. Turn MULTI JOG to select the low frequency effect attenuator level.
• As you turn it, the display changes to show the following:
0dB 10dB
0dB: Normally select this. 10dB: Select this when the bass sound is distorted.
Note:
Low frequency effect attenuator setting is not valid for the DVD MULTI playback mode.
Dynamic Range Compression Setting
You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.
• This function takes effect only when playing back a source using
Dolby Digital.
On the front panel ONLY:
1. Press SETTING repeatedly until
SETTING
“D. RANGE COMP.” (Dynamic Range Compression) appears on the display.
The display changes to show the current setting.
MULTI JOG
2. Turn MULTI JOG to select the appropriate item about the compression level.
• As you turn it, the display changes to show the following:
OFF MID MAX
OFF: Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID: Select this when you want to reduce the dynamic
range a little. (Factory setting.)
MAX: Select this when you want to apply the compression
effect fully. (Useful at night.)
15
Note:
Dynamic Range Compression setting is not valid for the DTS Digital Surround, MPEG Multichannel and DVD MULTI playback mode.
Digital Input (DIGITAL IN) Terminal Setting
When you use the digital input terminals, you have to register what components are connected to which terminals (DIGITAL IN 1/2/3).
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until
SETTING
“DIGITAL IN” appears on the display.
The display changes to show the current setting.
DIGITAL 2 terminal setting
DIGITAL 1 terminal setting
DIGITAL 3 terminal setting
MULTI JOG
2. Turn MULTI JOG to select the
appropriate digital terminal setting.
• As you turn it, the display changes to show the following: 1 DVD 2 CD 3 TV (or DBS*)
1 DVD 2 CD 3 MD 1 DVD 2 MD 3 TV (or DBS*) 1 CD 2 DVD 3 TV (or DBS*) 1 CD 2 DVD 3 MD 1 CD 2 MD 3 TV (or DBS*) 1 TV (or DBS*) 2 CD 3 DVD 1 TV (or DBS*) 2 CD 3 MD 1 TV (or DBS*) 2 DVD 3 MD 1 MD 2 CD 3 TV (or DBS*) 1 MD 2 CD 3 DVD 1 MD 2 DVD 3 TV (or DBS*) (back to the beginning)
If you have changed the source name from “TV SOUND” to
*
“DBS,” “DBS” appears.
Note:
When shipped from the factory, the DIGITAL IN terminals can be used as the digital input for the following components.
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
• DIGITAL 3 (optical): For digital TV broadcast tuner
Selecting the Analog or Digital Input Mode
When you have connected some digital source components using the digital terminals (see page 8), you need to change the input mode for these components to the appropriate digital input mode correctly — AUTO/PCM, DOLBY DIGITAL, DTS, or MPEG.
Before you start, remember...
The digital input (DIGITAL IN) terminal setting should be correctly done for the sources you want to select the digital input mode for. Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to digital input even if you follow the procedure below.
On the front panel:
1. Turn SOURCE SELECTOR until
SOURCE SELECTOR
the source (CD, MD, TV SOUND, DBS, or DVD)* for which you want to change the input mode appears on the display.
Note:
*
Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press INPUT ANALOG/DIGITAL repeatedly until the digital input
INPUT
ANALOG/DIGITAL
mode you want appears on the display.
• Each time you press the button, the input mode changes as
follows:
ANALOG
MPEG
(Digital)
DTS
(Digital)
AUTO/PCM
(Digital)
DOLBY DIGITAL
(Digital)
Normally select “AUTO/PCM,” so the receiver automatically detects the incoming digital signal format. (The DIGITAL AUTO indicator lights up on the display.)
– When the receiver can recognize the digital signal format
coming into the receiver, the frame of the digital signal
indicator for the detected signal lights up automatically.
– When the receiver cannot recognize the incoming signal
format correctly, the frame of the digital signal indicator
flashes. If this happens, select the same digital input mode with the incoming digital signal — either “DOLBY DIGITAL”, “DTS” or “MPEG.”
To change the input mode back to analog input, select “ANALOG.”
From the remote control:
1. Press the sour ce selecting button (CD, T APE/MD, TV/DBS, or DVD)* f or which y ou want to
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
change the input mode.
Note:
*
Among the sources listed above, you can select the digital input only for the sources which you have selected the digital input terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press ANALOG/DIGIT AL to
ANALOG/DIGITAL
change the input mode.
• Each time you press the button, the
input mode changes as follows:
ANALOG
MPEG
(Digital)
DTS
(Digital)
Notes:
• Noise may come out of the speakers while searching or skipping a
multi-sound source encoded with Dolby Digital, DTS Digital Surround or MPEG Multichannel. If this happens, select “DOLBY DIGITAL” , “DTS” or “MPEG” for digital input mode.
• When you change the source, the digital input mode will be
automatically reset to “AUTO/PCM.”
AUTO/PCM
(Digital)
DOLBY DIGITAL
(Digital)
English
16
English
2010 30 40 50 60 70 80 90
(Canceled)
00
Display
Showing the Text Information on the
Storing the Basic Settings and Adjustments — One Touch Operation
When you have connected an MD recorder or CD player equipped with TEXT COMPU LINK remote control system (see page 36), you can show the text information, such as disc title or track title, on the display of this receiver. To show it on the display, follow the procedure below.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until
SETTING
“FL DISPLAY” appears on the display.
The display changes to show the current setting.
2. Turn MULTI JOG to select either
MULTI JOG
the source name or the text information to be shown on the display.
• As you turn it, the display changes to show the following:
NORMAL TEXT
NORMAL: Source name appears during play. TEXT: Text information appears during play.
Note:
Though you have selected “TEXT,” the source name such as “CD” or “MD” appears if a playing disc has no text information.
Setting the AM Tuner Interval Spacing
Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing.
On the front panel ONLY:
To select the 10 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet. Hold down TUNER PRESET and press STANDBY/ON . Now the 10 kHz interval is selected.
TUNER PRESET
and
To change back to the 9 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet. Hold down FM MODE and press STANDBY/ON 9 kHz interval is selected.
FM MODE
and
STANDBY
STANDBY/ON
. Now the
STANDBY
STANDBY/ON
JVC’s One Touch Operation function is used to assign and store different sound settings for each different playing source. By using this function, you do not have to change the settings every time you change the source. The stored settings for the newly selected source are automatically recalled. The following can be stored for each source:
• Volume level (see page 11)
• Bass boost (see page 12)
• Input attenuator mode (see page 12)
• Subwoofer output level (see page 12)
• Balance (see page 13)
• SEA modes (see page 20)
• DSP modes – 3D-PHONIC mode settings (see page 24) – DAP mode settings (see page 24) – Surround mode settings (see page 25)
• DVD MULTI playback mode settings (see page 29)
On the front panel ONLY:
To store the sound settings
1. Press ONE TOUCH OPERATION.
ONE TOUCH OPERATION
The ONE TOUCH OPERATION lamp lights up, then the previously memorized settings are recalled.
2. Adjust the sound using the functions listed above.
The newly adjusted settings are memorized.
To recall the sound settings
With the ONE TOUCH OPERATION lamp lit, the settings for the currently selected source are recalled when the source is selected.
To cancel the One Touch Operation function
Press ONE TOUCH OPERATION so that the lamp goes off. (Even though the One Touch Operation function is canceled, the recalled sound effects remain active.)
Notes:
• If the source is FM or AM, you can assign a different setting for
each band.
• The DSP modes and DVD MULTI playback mode cannot be used at
the same time.
Using the Sleep Timer
Using the Sleep Timer, you can fall asleep to music and know the receiver will turn off by itself rather than play all night.
From the remote control ONLY:
Press SLEEP repeatedly.
The SLEEP indicator lights up on the display, and the shut-off time changes as follows (in minutes):
When the shut-off time comes
The receiver turns off automatically.
To check or change the time remaining until the shut-off time
Press SLEEP once. The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 00min.” appears on the display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
SLEEP
17

Receiving Radio Broadcasts

You can browse through all the stations or use the preset function to go immediately to a particular station.
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to “AUDIO/TV/ VCR.”
AUDIO/ TV/VCR
CATV/DBS
Tuning in Stations Manually
Before you start, remember...
• Check the AM tuner interval spacing (9 kHz or 10 kHz) for your area. (See page 17.)
On the front panel:
1. Turn SOURCE SELECTOR to
SOURCE SELECTOR
select the band (FM or AM).
The last received station of the selected band is tuned in.
2. Press FM/AM TUNING.
3. Turn MULTI JOG until you find
FM/AM TUNING
MULTI JOG
the frequency you want.
• Turning it clockwise increases the frequency.
• Turning it counterclockwise decreases the frequency.
• When you turn MULTI JOG quickly, the frequency keeps changing until a station is tuned in.
From the remote control:
TUNING
/REW
DOWN
FM/AM
FF/
UP
TUNING
1. Press FM/AM to select the band.
• Each time you press the button, the band alternates between FM and AM.
2. Press TUNING UP or TUNING DOWN repeatedly until you find the frequency you want.
• When you hold the button (and release it),
the frequency keeps changing until a station is tuned in.
Using Preset Tuning
Once a station is assigned to a channel number, the station can be quickly tuned. You can preset up to 30 FM and 15 AM stations.
To store the preset stations
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Tune in the station you want to preset (see
“Tuning in Stations Manually”).
• If you want to store the FM reception mode for this station, select the FM reception mode you want. See “Selecting the FM Reception Mode” on page 19.
2. Press TUNER (/SEA) MEMORY.
TUNER/SEA MEMORY
“CH-” appears and the channel number position starts flashing on the display for about 10 seconds.
3. Turn MULTI JOG to select a
MULTI JOG
channel number while the channel number position is flashing.
Note:
You can use the 10 keys on the remote control to select the preset number. When using the 10 keys, be sure that they are activated for the tuner, not for the CD and others. (See page 43.)
4. Press TUNER (/SEA) MEMORY
TUNER/SEA MEMORY
again while the selected channel number is flashing on the display.
The selected channel number stops flashing. The station is assigned to the selected channel number.
English
Note:
When a station of sufficient signal strength is tuned in, the TUNED indicator lights up on the display. When an FM stereo program is received, the STEREO indicator also lights up.
5. Repeat steps 1 to 4 until you store all the stations you want.
To erase a stored preset station
Storing a new station on a used number erases the previously stored one.
18
To tune in a preset station
English
On the front panel:
1. Turn SOURCE SELECTOR to select the band (FM or AM).
The last received station of the selected band is tuned in.
2. Press TUNER PRESET.
3. Turn MULTI JOG until you find the channel you want.
• Turning it clockwise increases the channel
numbers.
• Turning it counterclockwise decreases the
channel numbers.
SOURCE SELECTOR
TUNER PRESET
MULTI JOG
Note:
When using the FM MODE button on the remote control, be sure that the 10 keys are activated for the tuner, not for the CD and others. (See page 43.)
Assigning Names to Preset Stations
You can assign a name of up to four characters to each preset station. When a preset station is tuned in, its assigned name will appear on the display.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
• You can use the following characters: Space (_), A – Z, and 0 – 9.
From the remote control:
1. Press FM/AM.
FM/AM
• Each time you press the button, the band alternates between FM and AM.
2. Press the 10 keys to select a preset channel number.
• For channel number 5, press 5.
• For channel number 15, press +10 then 5.
• For channel number 20, press +10 then 10.
• For channel number 30, press +10, +10,
then 10.
CNTR TONE
123
TEST REAR-L
456
EFFECT REAR-R
7
/P 89
SEA MODE
10
RETURN
SUBWOOFER
0
FM MODE
CENTER
MENU
ENTER
+10
100+
Note:
When you use the 10 keys on the remote control, be sure that they are activated for the tuner, not for the CD and others. (See page 43.)
Selecting the FM Reception Mode
When an FM stereo broadcast is hard to receive or noisy
You can change the FM reception mode while receiving an FM broadcast.
• You can store the FM reception mode for each preset station.
Press FM MODE on the front panel or on the remote control.
• Each time you press the button, the FM reception mode alternates
between “AUTO MUTING” and “MONO.”
FM MODE
On the front panel
On the remote control
SUBWOOFER
0
FM MODE
On the front panel ONLY:
1. Tune in a preset station.
See the left.
2. Press TUNER (/SEA) MEMORY.
TUNER/SEA MEMORY
The preset channel number starts flashing for about 10 seconds.
• If you turn MULTI JOG while the preset channel number is flashing, you can change the preset channel number.
3. Press TUNER PRESET, while the preset channel number is flashing.
The first character position starts flashing.
4. Turn MULTI JOG to select the first character, while the first character position is flashing.
5. Press TUNER PRESET, while a character you want is flashing.
The next character position starts flashing.
6. Repeat steps 4 and 5 to enter up to four characters.
TUNER PRESET
MULTI JOG
TUNER PRESET
AUTO MUTING: When a program is broadcasted in stereo,
you will hear stereo sound; when in monaural, you will hear monaural sounds. This mode is also useful to suppress static noise between stations. The AUTO MUTING indicator lights up on the display.
MONO: Reception will be improved although you will lose the
stereo effect. In this mode, you will hear noise while tuning into the stations. The AUTO MUTING indicator goes off on the display.
19
7. Press TUNER (/SEA) MEMORY
TUNER/SEA MEMORY
while the last selected character is flashing after you have assigned a name.
To erase the input characters
Insert spaces using the same procedure described above.

Using the SEA Modes

The SEA (Sound Effect Amplifier) modes give you control of the way your music sounds.
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to “AUDIO/TV/ VCR.”
AUDIO/ TV/VCR
CATV/DBS
Selecting Your Favorite SEA Mode
On the front panel:
Press SEA MODE repeatedly until the SEA mode you want appears on the display.
• Each time you press the button, the SEA mode changes as follows:
SEA ROCK
SEA ROCK: Gives a heavy sound. Both high and low
SEA MUSICAL: Enhances the mid-frequency range, which
SEA MOVIE: Adds breadth to sounds so you feel like
SEA COUNTRY: Enhances the high-frequency range so that
SEA JAZZ: Gives a feeling of a live atmosphere.
SEA USERMODE: Your original SEA adjustment (see the
SEA OFF: No SEA mode is applied (see below).
SEA MUSICAL SEA MOVIE
SEA USERMODESEA OFF
frequencies are boosted.
the human voice is mostly made up of.
you are in a movie theater.
instruments such the violin and banjo are emphasized.
Good for acoustic music.
right).
SEA JAZZ
Notes:
• The SEA modes cannot be used for recording.
• When the SEA mode is turned on, the SEA indicator lights up on
the display.
• When the SEA mode is used with the DAP mode (see page 24),
sounds may be distorted. If this happens, turn off the DAP mode or decrease the effect level of the DAP mode.
SEA MODE
SEA COUNTRY
Creating Your Own SEA Mode
You can adjust and store your own SEA adjustment into memory (SEA USERMODE).
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel ONLY:
If you do not want to store your adjustment, but rather want to adjust the SEA temporarily, skip step 4 below.
1. Press SEA ADJUST repeatedly
SEA ADJUST
until the frequency range (100 Hz, 1 kHz or 10 kHz) you want appears on the display.
2. Turn MULTI JOG to adjust the
MULTI JOG
SEA level of the selected frequency range.
• Turning it clockwise increases the level.
• Turning it counterclockwise decreases the level.
3. Repeat step 1 and 2 to adjust other frequency
ranges if necessary.
4. Press (TUNER/) SEA MEMORY.
Your adjustment is stored into the SEA USERMODE.
TUNER/SEA MEMORY
English
To cancel the SEA mode
Press SEA MODE repeatedly until “SEA OFF” appears. The SEA indicator goes off from the display.
From the remote control:
SOUND
1. Press SOUND.
The 10 keys are activated for sound adjustments.
2. Press SEA MODE repeatedly until the SEA mode you want appears on the display.
To cancel the SEA mode
Press SEA MODE repeatedly until “SEA OFF” appears in step 2 above. The SEA indicator goes off from the display.
SEA MODE
10
RETURN
To recall your own SEA adjustment
Press SEA MODE repeatedly until “SEA USERMODE” appears.
To erase a stored adjustment
Storing a new adjustment into SEA USERMODE erases the previously stored one.
20

Using the DSP Modes

The built-in Surround Processor provides three types of the DSP (Digital Signal Processor) mode — 3D-PHONIC mode, DAP (Digital Acoustic Processor) mode and Surround mode.
English
3D-PHONIC modes
The 3D-PHONIC mode gives you such a nearly surround effect as is reproduced through the Dolby Surround decoder, which is widely used to reproduce sounds with a feeling of movement like those experienced in movie theaters. The 3D-PHONIC mode is the result of research on sound localization technology carried out at JVC for many years. This mode can be used when the front speakers are
connected to this receiver (without respect to the rear/center speaker connection).
3D ACTION: Best for action and war movies — where the
action is fast and explosive.
3D THEA TER: Reproduces the sound field of a large theater. This
mode can be selected when only front speakers are connected to this receiver and “REAR SPK” and “CENTER SPK” are set to “NONE” (see page 14).
DAP modes
The sound heard in a concert hall or club consists of direct sound and indirect sound — early reflections and reflections from behind. Direct sounds reach the listener directly without any reflection. On the other hand, indirect sounds are delayed by the distances of the ceiling and walls. These direct sounds and indirect sounds are the most important elements of the acoustic surround effects. The DAP mode can create these important elements, and gives you a real “being there” feeling. This mode can be used when the front
speakers are connected to this receiver (without respect to the rear/center speaker connection).
You can select one of the following to your preference while playing an analog or linear PCM source.
LIVE CLUB: Gives the feeling of a live music club with a low
ceiling.
DANCE CLUB:Gives a throbbing bass beat. HALL: Gives clear vocal and the feeling of a concert hall. PAVILION: Gives the spacious feeling of a pavilion with a high
ceiling.
Early reflections
Direct sounds
Reflections from behind
21
Surround modes
With this receiver, you can use four types of the Surround mode.
Following modes cannot be used when only the front speakers are connected to this receiver (without the rear speakers or center speaker).
JVC Theater Surround
In order to reproduce a more realistic sound field in your listening room while playing soundtracks of software encoded with Dolby Surround (bearing the mark
DOLBY SURROUND
) you can use JVC
Theater Surround.
English
Dolby Surround (Dolby Digital and Dolby Pro Logic)
*
Used to watch the soundtracks of software encoded with Dolby Digital (bearing the mark (bearing the mark
DOLBY SURROUND
DIGITAL
) or with Dolby Surround
). Dolby Surround encoding format records the left front channel, right front channel, center channel, and rear channel (total 4 channels) signals into 2 channels. The Dolby Pro Logic decoder built in this receiver decode these 2 channel signals into original 4 channel signals — matrix-based multichannel reproduction, and allows you to enjoy the realistic stereo sounds in your listening room. On the other hand, Dolby Digital encoding method (so called a discrete 5.1 channel digital audio format) records and compresses the left front channel, right front channel, center channel, left rear channel, right rear channel, and LFE channel (total 6 channels, but LFE channel is counted as 0.1 channel, therefore called 5.1 channels) signals digitally. Each channel is completely independent from other channel signals to avoid interference, therefore, you can obtain much better sound quality with much stereo and surround effects. The Dolby Digital decoder built in this receiver can create much more realistic sound field in your listening room. You may feel as if you were in a real theater. In addition, Dolby Digital enables stereo rear sounds, and sets the cutoff frequency of the rear treble at 20 kHz, comparing to 7 kHz for Dolby Pro Logic. These facts enhance the sound movement and being-there feelings much more than Dolby Pro Logic.
• To enjoy the software encoded with Dolby Digital, you must
connect the source component using the digital terminal on the rear of this receiver. (See page 8.)
DTS Digital Surround
**
DTS Digital Surround is another discrete 5.1 channel digital audio format available on CD, LD, and DVD software. Comparing to Dolby Digital, audio compression rate is relatively low. This fact allows DTS Digital Surround format to have more data recorded than Dolby Digital even using the same media, and to add breadth and depth to the reproduced sounds. As a result, DTS Digital Surround features natural, solid and clear sound.
• To enjoy the software encoded with DTS Digital Surround, you
must connect the source component using the digital terminal on the rear of this receiver. (See page 8.)
Notes:
• The DSP modes have no effect on monaural sources.
• When you select “DVD MULTI” as the source to play, you cannot select or adjust the DSP modes.
• The Ÿ
PRO LOGIC
decoder built in this receiver is activated.
indicator lights up when the Dolby Pro Logic
DVD MULTI Playback Mode
This receiver provides the DVD MULTI playback mode for reproducing the analog discrete 5.1 channel output mode of the DVD player or other equipment. You can adjust the DVD MULTI playback mode while playing back a video software such as a DVD using the analog discrete
5.1 channel output mode.
• For the DVD MULTI playback mode connection, see page 7.
• For details on the DVD MULTI playback mode, see page 29.
MPEG Multichannel
MPEG Multichannel is another discrete 5.1 channel digital audio format available on DVD software, and uses encoding method called MPEG2-Audio. (MPEG stands for “Motion Picture Expert Group” and has been originally developed for compressing video signals. ) To watch the soundtracks of video software bearing the mark
, the receiver can provide you with MPEG Multichannel decoder. MPEG Multichannel is automatically selected according to software played back and the speaker arrangement you have done.
• To enjoy the software encoded with MPEG Multichannel, you
must connect the source component using the digital terminal on the rear of this receiver. (See page 8.)
*
Manufactured under license from Dolby Laboratories. “Dolby,” “Pro Logic,” and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. ©1992–1997 Dolby Laboratories, Inc. All rights reserved.
**
Manufactured under license from Digital Theater Systems, Inc. US Pat. No. 5,451,942 and other world-wide patents issues and pending. “DTS” and “DTS Digital Surround” are trademarks of Digital Theater Systems, Inc. ©1996 Digital Theater Systems, Inc. All rights reserved.
22
English
Available DSP Modes According to the Speaker Arrangement
Available DSP modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see page 14).
Front
speaker
Front
speaker
Front
speaker
Rear
speaker
Front
speaker
Rear
speaker
Speaker arrangements
TV
TV
Center speaker
TV
TV
Center speaker
Front
speaker
Front
speaker
Front
speaker
Rear
speaker
Front
speaker
Rear
speaker
Available DSP modes
Each time you press DSP MODE on the front panel or SURROUND MODE on the remote control, the DSP modes change as follows:
• 3D THEATER
• LIVE CLUB
• DANCE CLUB
• HALL
• PAVILION
• 3D ACTION
• DSP OFF (DSP mode is canceled)
Each time you press DSP MODE on the front panel or SURROUND MODE on the remote control, the DSP modes change as follows:
By pressing DSP MODE:
• THEATER
• LIVE CLUB
• DANCE CLUB
• HALL
• PAVILION
• 3D ACTION
• DSP OFF (DSP mode is canceled)
By pressing SURROUND MODE:
• DOLBY/DTS/MPEG SURROUND (DOLBY PRO LOGIC, DOLBY DIGITAL*, DTS SURROUND**, or MPEG SURROUND***)
• THEATER
• LIVE CLUB
• DANCE CLUB
• HALL
• PAVILION
• 3D ACTION
To activate the Surround
• DSP OFF (DSP mode is canceled)
mode, press SURROUND ON/ OFF button so that the lamp on the button lights up.
To activate the Surround mode, you can also use the
SURROUND ON/OFF button.
*
Activated automatically only when “AUTO/PCM” is selected as the digital input and playback source is encoded with Dolby Digital.
**
Activated automatically only when “AUTO/PCM” is selected as the digital input and playback source is encoded with DTS Digital Surround.
***
Activated automatically only when “AUTO/PCM” is selected as the digital input
and playback source is encoded with MPEG Surround.
Notes:
• If Surround mode is canceled while playing back a multichannel source such as Dolby Digital, DTS Digital Surround and MPEG Multichannel, all channel signals are mixed with left and right front channel and are output through the front speakers.
• While playing back a multichannel source such as Dolby Digital, DTS Digital Surround and MPEG Multichannel, Theater Surround, DAP modes, and 3D­PHONIC modes cannot be used. On the other hands, if you select a Dolby Digital, DTS Digital Surround and MPEG Multichannel as the source to play while using any of Theater Surround, DAP modes, and 3D-PHONIC modes, the currently selected mode will be canceled and Dolby Digital, DTS Digital Surround or MPEG Multichannel mode will be activated.
23
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to “AUDIO/TV/ VCR.”
AUDIO/ TV/VCR
CATV/DBS
3. Press EFFECT to select an effect level you want.
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 4DSP EFFECT 5
EFFECT
7
/P
English
Adjusting the 3D-PHONIC Modes
Once you have adjusted the 3D-PHONIC modes, the adjustment is memorized for each 3D-PHONIC mode.
Before you start, remember...
Make sure that you have set the speaker information correctly (see page 14).
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
On the front panel:
1. Press DSP MODE repeatedly until
DSP MODE
“3D ACTION” or “3D THEATER” appears on the display.
The 3D-PHONIC, DSP, and Ÿ PRO LOGIC indicators also light up on the display.
2. Adjust the effect level.
1) Press (BALANCE/) SURROUND
BALANCE/SURROUND
ADJUST
ADJUST repeatedly until “DSP EFFECT” appears on the display.
The display changes to show the current setting.
2) Turn MULTI JOG to select the effect
MULTI JOG
level.
• As you turn it, the effect level changes as follows:
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 4DSP EFFECT 5
As the number increases, the selected 3D-PHONIC mode becomes stronger.
From the remote control:
1. Press SURROUND MODE repeatedly until “3D ACTION” or
SURROUND
MODE
“3D THEATER” appears on the display.
The 3D-PHONIC, DSP, and Ÿ PRO LOGIC indicators also light up on the display.
As the number increases, the selected 3D-PHONIC mode becomes stronger.
Adjusting the DAP Modes
Once you have adjusted the DAP modes, the adjustment is memorized for each DAP mode.
Before you start, remember...
Make sure that you have set the speaker information correctly (see page 14).
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
• You cannot adjust the rear speaker output level when you have set “REAR SPK” to “NONE.” See page 14.
• When the DAP mode is used with the SEA mode (see page 20), sounds may be distorted. If this happens, turn off the SEA mode.
On the front panel:
1. Press DSP MODE repeatedly until
DSP MODE
the DAP mode — LIVE CLUB, DANCE CLUB, HALL, or PAVILION — appears on the display.
The DSP indicator also lights up on the display.
• When you have set “REAR SPK” to “NONE,” the 3D­PHONIC indicator also lights up.
2. Adjust the speaker output levels.
1) Press (BALANCE/) SURROUND
ADJUST repeatedly until one of the indications appears on the display.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Turn MULTI JOG to adjust the
selected speaker output level (from –10 dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output level.
BALANCE/SURROUND
ADJUST
MULTI JOG
2. Press SOUND.
The 10 keys are activated for sound adjustments.
SOUND
24
3. Adjust the effect level.
English
1) Press (BALANCE/) SURROUND ADJUST repeatedly until “DSP EFFECT” appears on the display.
The display changes to show the current setting.
2) Turn MULTI JOG to select the effect level.
• As you turn it, the effect level changes
as follows:
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
As the number increases, the selected DAP mode becomes stronger.
BALANCE/SURROUND
ADJUST
Adjusting the Surround Modes
Once you have adjusted the Surround modes, the adjustment is memorized for each Surround mode.
MULTI JOG
Dolby, DTS and MPEG Surround adjustments
Before you start, remember...
Make sure that you have set the speaker information correctly (see page 14).
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
• You cannot adjust the rear speaker output le vels when you have set
DSP EFFECT 4DSP EFFECT 5
“REAR SPK” to “NONE.” See page 14.
• You cannot adjust the center speaker output level you have set “CENTER SPK” to “NONE.” See page 14.
From the remote control:
1. Press SURROUND MODE repeatedly until the DAP mode — LIVE CLUB, DANCE CLUB, HALL, or PAVILION — appears on the display.
The DSP indicator also lights up on the display.
• When you have set “REAR SPK” to “NONE,” the 3D-
PHONIC indicator also lights up.
2. Press SOUND.
The 10 keys are activated for sound adjustments.
3. Adjust the speaker output levels.
• To adjust the left rear speaker level, press
REAR•L –/+ (from –10 dB to +10 dB).
• To adjust the right rear speaker level, press
REAR•R –/+ (from –10 dB to +10 dB).
4. Press EFFECT to select an effect level you want.
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
SURROUND
MODE
SOUND
REAR•L
56
ENTERENTER
REAR•R
89
EFFECT
7
/P
From the remote control:
1. Press SURROUND ON/OFF to activate an appropriate Surround
SURROUND
ON/OFF
mode — PRO LOGIC, DOLBY DIGITAL, DTS SURROUND or MPEG SURROUND.
• Each time you press the button, the Surround mode turns on
and off alternately.
• When “PRO LOGIC” is selected, the Ÿ PRO LOGIC
indicator lights up on the display.
Note:
You can also press SURROUND MODE to activate an appropriate Surround mode.
2. Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker output balance.
“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:
TEST TONE L
(Left front speaker)
TEST TONE LS
(Left rear speaker)
TEST TONE C
(Center speaker)
TEST TONE RS
(Right rear speaker)
TEST
TEST TONE R
(Right front speaker)
4
DSP EFFECT 4DSP EFFECT 5
As the number increases, the selected DAP mode becomes stronger.
25
Notes:
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when “CENTER
SPK” is set to “NONE” (see page 14).
• No test tone comes out of the rear speakers when “REAR SPK”
is set to “NONE” (see page 14).
• If the TV is turned on and the proper video input is selected on
the TV, the test tone screen will appear on the TV.
4. Adjust the speaker output levels.
• To adjust the center speaker level, press CENTER –/+ (from –10 dB to +10 dB).
• To adjust the left rear speaker level, press REAR•L –/+ (from –10 dB to +10 dB).
• To adjust the right rear speaker level, press REAR•R –/+ (from –10 dB to +10 dB).
CENTER
23
MENUMENU
5. Press TEST again to stop the test tone.
REAR•L
56
ENTER
REAR•R
89
TEST
4
On the front panel:
You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.
1. Press SURROUND ON/OFF to
SURROUND ON/OFF
activate an appropriate Surround mode — PRO LOGIC, DOLBY DIGITAL, DTS SURROUND or MPEG SURROUND.
• Each time you press the button, the Surround mode turns on and off alternately.
• When “PRO LOGIC” is selected, the Ÿ PRO LOGIC indicator lights up on the display.
2. Adjust the speaker output levels.
1) Press (BALANCE/) SURROUND
ADJUST repeatedly until one of the indications appears on the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Turn MULTI JOG to adjust the
selected speaker output level (from –10 dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
BALANCE/SURROUND
ADJUST
MULTI JOG
JVC Theater Surround adjustments
Before you start, remember...
Make sure that you have set the speaker information correctly (see page 14).
• There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.
• You cannot adjust the rear speaker output le vels when you have set “REAR SPK” to “NONE.” See page 14.
• You cannot adjust the center speaker output level when you have set “CENTER SPK” to “NONE.” See page 14.
From the remote control:
1. Press SURROUND MODE
repeatedly until “THEATER”
SURROUND
MODE
appears on the display.
The Ÿ PRO LOGIC and DSP indicators also light up on the display.
SOUND
2. Press SOUND.
The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker
output balance.
TEST
4
“TEST TONE L” starts flashing on the display, and a test tone comes out of the speakers in the following order:
TEST TONE L
(Left front speaker)
TEST TONE LS
(Left rear speaker)
TEST TONE C
(Center speaker)
TEST TONE R
(Right front speaker)
TEST TONE RS
(Right rear speaker)
Notes:
• You can adjust the speaker output levels without outputting the test tone.
• No test tone comes out of the center speaker when “CENTER SPK” is set to “NONE” (see page 14).
• No test tone comes out of the rear speakers when “REAR SPK” is set to “NONE” (see page 14).
• If the TV is turned on and the proper video input is selected on the TV, the test tone screen will appear on the TV.
4. Adjust the speaker output levels.
• To adjust the center speaker level, press CENTER –/+ (from
–10 dB to +10 dB).
• To adjust the left rear speaker level, press REAR•L –/+ (from
–10 dB to +10 dB).
• To adjust the right rear speaker level, press REAR•R –/+ (from
–10 dB to +10 dB).
CENTER
23
MENUMENU
REAR•L
56
ENTERENTER
REAR•R
89
English
26
5. Press TEST again to stop the test tone.
English
6. Press EFFECT to select an effect level you want.
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
TEST
4
EFFECT
7
/P
Activating the DSP Modes
You can use only one DSP mode at a time. When a DSP mode is activated, another DSP mode is canceled if in use.
For Dolby Pro Logic, Dolby Digital, DTS Digital Surround and MPEG Multichannel
DSP EFFECT 4DSP EFFECT 5
As the number increases, JVC Theater Surround becomes stronger.
On the front panel:
You can also use the buttons on the front panel to adjust the Surround modes. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.
1. Press DSP MODE repeatedly until
DSP MODE
“THEATER” appears on the display.
The Ÿ PRO LOGIC and DSP indicators also light up on the display.
2. Adjust the speaker output levels.
1) Press (BALANCE/) SURROUND
ADJUST repeatedly until one of the indications appears on the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Turn MULTI JOG to adjust the
selected speaker output level (from –10 dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
BALANCE/SURROUND
ADJUST
MULTI JOG
1. Press SURROUND ON/OFF so that the lamp on the front panel button lights up.
• Each time you press the button, the Dolby/DTS/MPEG
Surround turns on and off alternately.
SURROUND ON/OFF
On the front panel
SURROUND
ON/OFF
On the remote control
2. Select and play a sound source.
• To enjoy Dolby Pro Logic, play back a software encoded with
Dolby Surround and labeled with
DOLBY SURROUND
• To enjoy Dolby Digital, play back a software encoded with
Dolby Digital and labeled with
DIGITAL
• To enjoy DTS Digital Surround, play back a software encoded
with DTS Digital Surround and labeled with
• To enjoy MPEG Multichannel, play back a software encoded
with MPEG Multichannel and labeled with mark.
To cancel the Dolby/DTS/MPEG Surround mode
Press SURROUND ON/OFF again so that the lamp on the front panel button goes off. (“SURROUND OFF” appears on the display.)
SURROUND ON/OFF
SURROUND
ON/OFF
mark.
mark.
mark.
3. Adjust the effect level.
1) Press (BALANCE/) SURROUND ADJUST repeatedly until “DSP EFFECT” appears on the display.
The display changes to show the current setting.
2) Turn MULTI JOG to select the effect level.
As you turn it, the effect level changes as follows:
DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3
DSP EFFECT 4DSP EFFECT 5
As the number increases, JVC Theater Surround becomes stronger.
27
BALANCE/SURROUND
ADJUST
MULTI JOG
On the front panel
On the remote control
For the other DSP modes
On the front panel:
1. Press DSP MODE repeatedly until
DSP MODE
the mode you want appears on the display.
• Each time you press the button, the DSP
modes change. (See page 23 for more details.)
2. Select and play a sound source.
• To enjoy 3D-PHONIC and JVC Theater Surround, play back a
software encoded with Dolby Surround and labeled with
DOLBY SURROUND
mark.
––––––––––––––– MEMO –––––––––––––––
Use this column to write down your DSP mode adjustments for your future reference.
English
To cancel the DSP mode
DSP MODE
Press DSP MODE repeatedly until “DSP OFF” appears on the display.
From the remote control:
1. Press SURROUND MODE repeatedly until the DSP mode you
SURROUND
MODE
want appears on the display.
• Each time you press the button, the DSP
modes change.
2. Select and play a sound source.
• To enjoy 3D-PHONIC and JVC Theater Surround, play back a
software encoded with Dolby Surround and labeled with
DOLBY SURROUND
To cancel the DSP mode
Press SURROUND MODE repeatedly until “DSP OFF” appears on the display.
Note:
While playing back MPEG Multichannel or Dolby Digital source through a digital input terminal, you can neither select nor adjust any DSP mode. If any DSP mode is in use, it is temporarily canceled, and normal stereo sounds are reproduced. To enjoy the MPEG Multichannel and Dolby Digital source with DSP mode, change the input mode from the digital input to the analog input. (See page 16.)
mark.
SURROUND
MODE
28

Using the DVD MULTI Playback Mode

This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD player. Before playing back a DVD, refer also to the manual supplied with the DVD player.
English
IMPORTANT:
When using the remote control, check to see if its remote control mode selector is set to the correct position: To operate this receiver, set it to “AUDIO/TV/ VCR.”
AUDIO/ TV/VCR
CATV/DBS
Activating the DVD MULTI Playback Mode
You can adjust the DVD MULTI playback mode while playing back a DVD using the analog discrete output mode on the DVD player. Once you have made adjustments, the receiver memorizes the adjustments until you change them. You also need to set the DVD player to the analog discrete output mode.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
From the remote control:
1. Press DVD MULTI so that “DVD MULTI” appears on the display.
Note:
When you select “DVD MULTI” as the source to play, the DSP mode is canceled temporarily, and the SURROUND ON/OFF and SURROUND MODE buttons do not work.
2. Select the analog discrete output mode on the DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following steps.
3. Press SOUND.
The 10 keys are activated for adjusting the sound.
DVD MUILTI
SOUND
On the front panel:
1. Turn SOURCE SELECTOR until
SOURCE SELECTOR
“DVD MULTI” appears on the display.
Note:
When you select “DVD MULTI” as the source to play, the DSP mode is canceled temporarily, and the SURROUND ON/OFF and DSP MODE buttons do not work.
2. Select the analog discrete output mode on the DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following steps.
3. Adjust the speaker output levels.
1) Press (BALANCE/) SURROUND
ADJUST repeatedly until one of the indications appears on the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Turn MULTI JOG to adjust the
selected speaker output level (from –10 dB to +10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
BALANCE/SURROUND
ADJUST
MULTI JOG
4. Adjust the speaker output levels.
• To adjust the center speaker level, press CENTER –/+ (from – 10 dB to +10 dB).
• To adjust the left rear speaker level, press REAR•L –/+ (from –10 dB to +10 dB).
• To adjust the right rear speaker level, press REAR•R –/+ (from –10 dB to +10 dB).
CENTER
23
MENUMENU
REAR•L
56
ENTER
REAR•R
89
29

Using the On-Screen Menus

You can use the Menus on the TV screen to control the receiver. To use this function, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 7), and set the TV’s input mode to the proper position to which the receiver is connected.
• When the TV’s input mode is incorrect; for example, a different video input or TV tuner mode is selected, you cannot show the Menus on the TV screen.
English
On-Screen Operation buttons (on the remote control)
TV/CATV/DBS
ANALOG/DIGITAL
CENTER
123
MENUMENU
TEST REAR-L
456
ENTERENTER
EFFECT REAR-R
/P
89
7
SEA MODE
SUBWOOFER
10
0
RETURN
FM MODE
SET
CHANNEL VOLUMETV VOL
TAPE/MD
VCR
CONTROL
PLAY
FF/
TUNING
STOP PAUSE
SLEEP
CATV/DBS
DISPLAY
VCR
+10
100+
AUDIO/ TV/VCR
TEXT
MUTING
MENU
SET
EXIT
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
SURROUND
ON/OFF
SURROUND
MODE
CD-DISC
SOUND
MENU
EXIT
TV/VIDEO
/REW
DOWN UP
REC
RM-SRX7001P REMOTE CONTROL
Selecting Different Sources for Picture and
Sound (Also see page 11)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the MAIN MENU.
2. Press % / fi to move to “VISUAL.”
3. Press @ / # to select a different video source.
4. When you finish, press EXIT.
The menu disappears from the TV.
Activating the DSP Modes (Also see page 27)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move to “MODE.”
Selecting the Source to Play (Also see page 10)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the MAIN MENU.
Shows the buttons you can use on the current menu. In this case, use % / to move up and down, and @ / # to select, adjust or set the item.
Notes:
• “INPUT” appears only when the digital input (DIGITAL IN) terminal setting have been correctly done for the digital source currently selected. (See page 16.)
• The on-screen display will disappear if no operation is done for about 1 minute.
2. Press % / fi to move to “SOURCE.”
3. Press @ / # to select the source.
4. When you finish, press EXIT.
The menu disappears from the TV.
3. Press @ / # to select the DSP mode you want to use.
4. When you finish, press EXIT.
The menu disappears from the TV.
Selecting the Analog or Digital Input Mode
(Also see page 16)
This selection is only possible when the digital input (DIGITAL IN) terminal setting have been correctly done for the digital source currently selected.
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move to “INPUT.”
3. Press @ / # to select the digital or analog input you want.
For details, see page 16.
4. When you finish, press EXIT.
The menu disappears from the TV.
30
Adjusting the Front Speaker Output Balance
English
(Also see page 13)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the MAIN MENU.
Adjusting the Subwoofer Output Level
(Also see page 12)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the MAIN MENU.
2. Press % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / to move to “BAL.” (Balance).
4. Press @ / # to adjust the balance.
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Reinforcing the Bass
(Also see page 12)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / to move to “BASS BOOST.”
4. Press @ / # to turn the bass boost function “ON” or “OFF.”
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Attenuating the Input Signal
(Also see page 12)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / to move to “INPUT ATT.”
4. Press @ / # to turn the Input Attenuator mode “ATT ON” or “NORMAL.”
2. Press % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / fi to move to “SUBWFR LEVEL.”
4. Press @ / # to adjust the subwoofer output level.
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Adjusting the DSP Modes
(Also see pages 24 – 27)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / to move to “MODE.”
3. Press @ / # to select the DSP mode you want to adjust.
• In this example,
“THEATER” is selected.
4. Press % / fi to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
5. Press % / fi to move to “SURROUND LEVEL,” then press @ / #.
The SURROUND LEVEL menu appears.
6. Press % / fi to move to the item you want to set or adjust, then press @ / #.
On these adjustment menus, you can do the following:
For 3D-PHONIC
“DSP EFFECT”: Select the effect level.
(3D ACTION, 3D THEATER):
5. When you finish, press EXIT repeatedly until the menu disappears from the TV.
31
For DAP
For Dolby Pro Logic:
For Dolby Digital, DTS Digital Surround and MPEG Multichannel:
For JVC Theater Surround:
(LIVE CLUB, DANCE CLUB, HALL, PAVILION):
“REAR L LEVEL”: Adjust the left rear speaker output
level. *
“REAR R LEVEL”: Adjust the right rear speaker output
level. *
“DSP EFFECT”: Select the effect level.
“TEST TONE”: Output a test tone. “CENTER LEVEL”: Adjust the center speaker output
level. **
“REAR L LEVEL”: Adjust the left rear speaker output
level. *
“REAR R LEVEL”: Adjust the right rear speaker output
level. *
“TEST TONE”: Output a test tone. “CENTER LEVEL”: Adjust the center speaker output
level. **
“REAR L LEVEL”: Adjust the left rear speaker output
level. *
“REAR R LEVEL”: Adjust the right rear speaker output
level. *
“TEST TONE”: Output a test tone. “CENTER LEVEL”: Adjust the center speaker output
level. **
“REAR L LEVEL”: Adjust the left rear speaker output
level. *
“REAR R LEVEL”: Adjust the right rear speaker output
level. *
“DSP EFFECT”: Select the effect level.
6. Press % / to move to the item you want to set or adjust, then press @ / #.
On this adjustment menu, you can do the following:
“CENTER LEVEL”:Adjust the center speaker output level. “REAR L LEVEL”: Adjust the left rear speaker output
level.
“REAR R LEVEL”: Adjust the right rear speaker output
level.
7. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Selecting Your Favorite SEA Mode
(Also see page 20)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / fi to move to “SEA,” then press @ / #.
The SEA menu appears.
4. Press % / fi to move
to “SEA MODE.”
English
Notes:
*
Not displayed when “REAR SPK” is set to “NONE” (see page
14).
**
Not displayed when “CENTER SPK” is set to “NONE” (see page 14).
7. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Adjusting the DVD MULTI Playback Mode
(Also see page 29)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move to “SOURCE.”
3. Press @ / # to select “DVD MULTI.”
4. Press % / to move
to “SOUND
CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
5. Press % / to move to “SURROUND LEVEL,” then press @ / #.
The SURROUND LEVEL menu appears.
5. Press @ / # to select the SEA mode you want.
6. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Creating Your Own SEA Mode
(Also see page 20)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / to move to “SOUND CONTROL,” then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / to move to “SEA,” then press @ / #.
The SEA menu appears.
32
4. Press % / to move
English
to “SEA ADJUST.”
The SEA ADJUST menu appears.
5. Press % / / @ / # to adjust the SEA mode as you want.
@ / # : Select the frequency ranges. % / : Adjust the frequency levels.
6. Press SET to store the setting into the SEA USERMODE.
• If you press EXIT, without pressing SET in this step, you can
return to the SEA menu. (The adjustment you have made is active but not stored.)
7. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Setting the Basic Setting Items (Also see
pages 14 – 17)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / to move to “SETTING,” then press @ / #.
The SETTING 1 or SETTING 2 menu appears.
3. Press % / to move to the item you want to set or adjust, then press @ / #.
• To go to the SETTING 2
menu, move to “NEXT PAGE,” then press @ / #.
• To go back to the SETTING
1 menu, move “PREVIOUS PAGE,” then press @ / #.
On the SETTING 1 and 2 menus, you can do the following:
to
“LFE ATT.”: Set the low frequency effect attenuator
level (see page 15).
“COMP.”: Set the dynamic range compression
(see page 15).
“DIGITAL 1/2/3”: Set the digital input terminals
(see page 16).
“FL DISP.”: Shows the disc text information on the
display (see page 17).
Notes:
*
Not adjustable when “CENTER SPK” is set to “NONE” (see page 14).
**
Not adjustable when “REAR SPK” is set to “NONE” (see page
14).
4. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Operating the Tuner (Also see pages 18 and 19)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
2. Press % / to move to “TUNER CONTROL,” then press @ / #.
The TUNER CONTROL menu appears.
3. Press % / fi to move to the item you want to set or adjust, then press @ / #.
On the TUNER CONTROL menu, you can do the following:
“PRESET CH”: Select a preset channel station. “BAND”: Select the band. “FREQUENCY”: Tune in a station manually. “FM MODE”: Select the FM reception mode.* “PRESET MEMORY”: See “Storing the Preset Stations” on
the next page.
Note:
*
Not displayed when an AM station is selected.
4. When you finish, press EXIT repeatedly until the menu disappears from the TV.
“SUBWOOFER”: Set the subwoofer information (see
page 14).
“FRONT SPK”: Set the front speaker information (see
page 14).
“CENTER SPK”: Set the center speaker information (see
page 14).
“REAR SPK”: Set the rear speaker information (see
page 14).
“CNTR DELAY”: Adjust the delay time of the center
speaker output (see page 14).*
“REAR DELAY”: Adjust the delay time of the rear
speaker output (see page 14).**
“CROSSOVER”: Set the crossover frequency
(see page 15).
33
Storing the Preset Stations (Also see page 18)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the MAIN MENU.
2. Press % / to move to “TUNER CONTROL,” then press @ / #.
The TUNER CONTROL menu appears.
3. Tune into a station on the TUNER CONTROL menu, referring to “Operating the Tuner” on the previous page.
4. Press % / to move to “PRESET MEMORY,” then press @ / #.
The PRESET MEMORY menu appears.
5. Press @ / # to select a preset station number you want.
6. Press SET to store the setting.
7. When you finish, press EXIT repeatedly until the menu disappears from the TV.
Assigning Names to Preset Stations
(Also see page 19)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / / @ / # buttons also displays the
MAIN MENU.
6. Press % / to move to “PRESET NAME,” then press SET.
The character entry screen appears.
7. Press % / / @ / # to move
in front of a
character you want.
You can also select the following:
: To enter space
: To erase the character : To go back to the previous character position or go
to the next character position
8. Press SET to enter the selected character.
9. Repeat steps 7 and 8 to enter up to four
characters.
10.Press % / / @ / # to move
to “PRESET NAME,” then press SET to store the setting.
The TUNER CONTROL menu appears again.
11.When you finish, press EXIT repeatedly until the menu disappears from the TV.
English
2. Press % / to move to “TUNER CONTROL,” then press @ / #.
The TUNER CONTROL menu appears.
3. Press % / fi to move to “PRESET CH.”
4. Press @ / # to select a preset station.
5. Press % / to move to “PRESET MEMORY,” then press @ / #.
The PRESET MEMORY menu appears.
34

COMPU LINK Remote Control System

The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on the receiver.
English
To use this remote control system, you need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see below) in addition to the connections using cables with RCA pin plugs (see pages 5 and 6).
• Make sure that the AC power cords of these components are
unplugged before connection. Plug the AC power cords only after all connections are complete.
CD player
Cassette deck
or
MD recorder
COMPU LINK – 3
(SYNCHRO)
Turntable
Notes:
• If your audio component has two COMPU LINK-3 (SYNCHRO)
jacks, you can use either one. If it has only one COMPU LINK-3 (SYNCHRO) jack, connect it so that it is the last item in the series of components. (For example, the turntable or CD player in the diagram above.)
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See page 13.)
• Refer also to the manuals supplied with your audio components.
This remote control system allows you to use four functions listed below.
Remote Control through the Remote Sensor on the Receiver
You can control the connected audio components through the remote sensor on the receiver using this remote control. Aim the remote control directly at the remote sensor on the receiver. For details, see pages 43 and 44.
Automatic Power On/Off (Standby): only possible with the COMPU LINK-3 connection
Both the CD player and cassette deck (or MD recorder) turn on and off (standby) along with the receiver. When you turn on the receiver, the CD player or cassette deck (or MD recorder) will turn on automatically, depending on which component has been previously selected. When you turn off the receiver, both the CD player and cassette deck (or MD recorder) will turn off (standby).
Synchronized Recording
Synchronized recording means the cassette deck (or MD recorder) starts recording as soon as a CD or a record begins playing.
To use synchronized recording, follow these steps:
1. Put a tape in the cassette deck (or an MD in the MD recorder), and a disc in the CD player (or a record on the turntable).
2. Press the record () button and the pause (8) button on the cassette deck (or MD recorder) at the same time.
This puts the cassette deck (or MD recorder) into recording pause. If you do not press the record () button and pause (8) button at the same time, the synchronized recording feature will not operate.
3. Press the play (3) button on the CD player or on the turntable.
The source changes on the receiver, and as soon as play starts, the cassette deck (or MD recorder) starts recording. When the play ends, the cassette deck (or MD recorder) enters recording pause, and stops about 4 seconds later.
Notes:
• During synchronized recording, the selected source cannot be
changed.
• If the power of any component is shut off during synchronized
recording, the COMPU LINK remote control system may not operate properly. In this case, you must start again from the beginning.
Automatic Source Selection
When you press the play ( on its own remote control, the receiver automatically turns on and changes the source to the component. On the other hand, if you select a new source on the receiver or on the remote control, the selected component begins playing immediately. In both cases, the previously selected source continues playing without sound for a few seconds.
33
3) button on a connected component or
33
35

TEXT COMPU LINK Remote Control System

The TEXT COMPU LINK remote control system has been newly developed to deal with the disc information recorded in the CD Text with the TEXT COMPU LINK remote control system through the receiver.
*
and MDs. Using these information in the discs, you can operate the CD player or MD recorder equipped
English
CONNECTIONS:
To use this remote control system, you need to connect the CD player and/or MD recorder you want to operate, following the procedures below.
1. If you have already plugged your CD player, MD recorder, and this receiver into the AC outlets, unplug their AC power cords first.
2. Connect your CD player, MD recorder, and this receiver as follows, through the COMPU LINK-3 (SYNCHRO) jacks and TEXT COMPU LINK jacks.
1) COMPU LINK-3 (SYNCHRO) jacks: Use the cables with
the monaural mini-plugs (not supplied with this receiver).
CD player
MD recorder
COMPU LINK – 3
(SYNCHRO)
2) TEXT COMPU LINK jacks: Use the cables with the
stereo mini-plugs (not supplied with this receiver).
CD player
MD recorder
TEXT
COMPU LINK
3. Connect your CD player, MD recorder and this receiver, using the cables with RCA pin plugs (see pages 5 and 6).
4. Plug the AC power cords of these components above into the AC outlets.
5. When turning on these components for the first time, turn on the connected components first, then turn on this receiver.
FUNCTIONS:
This remote control system allows you to use the functions listed below.
Displaying the Disc Information on the TV screen
Disc information such as its performer and disc title (and track titles only when a CD Text is selected) is shown on the TV screen.
Disc Search: Only for CD Player
This remote control system can allow you to search discs by the performer, disc title, and music genre. With this disc search, you can easily find the disc you want to play.
Disc Title Input:
If your CD player or MD recorder has the disc memory function, you can input the following information about the normal audio CDs or MDs on the TV screen.
• For CDs: Performer, disc title, and music genre
• For MDs: Disc title and song titles
*
What is a CD Text?
In a CD Text, some information about the disc (its disc title, performer, composer, arranger, etc.) is recorded.
Notes:
• If your audio component has two COMPU LINK-3 (SYNCHRO) jacks, you can use either one. If it has only one COMPU LINK-3 (SYNCHRO) jack, connect it so that it is the last item in the series of components. (For example, the CD player in the diagram to the left.)
• If your audio component has two TEXT COMPU LINK jacks, you can use either one. If it has only one TEXT COMPU LINK jack, connect it so that it is the last item in the series of components. (For example, the CD player in the diagram to the left.)
• “TEXT COMPULINK SOURCE NOT CONNECTED” appears on the display in the following cases:
– When the connections explained to the left are not correctly done. – When you try to use the TEXT COMPU LINK function a few
seconds after you turn on the connected equipment. This is not a malfunction of the units.
• Refer also to the manuals supplied with your CD player or MD recorder.
IMPORTANT:
If you turn on the receiver before turning on the other components after connecting the components, the TEXT COMPU LINK remote control system does not work correctly. If this happens:
1. Turn off all the components including this receiver.
2. Turn on the connected components.
3. Turn on this receiver.
36
English
OPERATIONS
To use this remote control system, you need to connect the TV to the MONITOR OUT jack on the rear panel (see page 7), and set the TV’s input mode to the proper position to which the receiver is connected. Make sure you have connected the CD player or
MD recorder equipped with the TEXT COMPU LINK remote control system. If not, you cannot use the following functions.
On-Screen Operation buttons (on the remote control)
TV/CATV/DBS
ANALOG/DIGITAL
CENTER
123
MENU
TEST REAR-L
456
ENTER
EFFECT REAR-R
/P
89
7
SEA MODE
SUBWOOFER
10
0
RETURN
FM MODE
SET
CHANNEL VOLUMETV VOL
TAPE/MD
VCR
CONTROL
FF/
PLAY
TUNING STOP PAUSE
SLEEP
CATV/DBS
DISPLAY
MUTING
VCR
+10
100+
AUDIO/ TV/VCR
TEXT
MENU
EXIT
SET
DISPLAY
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
SURROUND
ON/OFF
SURROUND
MODE
CD-DISC
SOUND
MENU
EXIT
TV/VIDEO
/REW
DOWN UP
REC
RM-SRX7001P REMOTE CONTROL
TEXT
1 Source name: CD or MD 2 Select or , then press SET to change the disc. 3 Track numbers and track titles.
• The current playing (selected) track is indicated in yellow.
• When you move
to a track number, you can
change the track information by pressing @ / #. Each time you press the button, track information alternates between its track title and its performer. (You can also start playing the track by pressing SET.)
4 Select this (move
in front), then press SET to go to
the DISC SEARCH screen (see page 38).
5 Select this (move in front), then press SET to go to
the TITLE INPUT screen (see page 39).
6 This appears only when a CD Text is selected. 7 Disc information such as the disc title, performer, and
music genre. When this is selected (
in front), you can change the disc information by pressing @ / #. Each time you press the button, disc information (see “Note on 7”) changes.
8 Select
or , then press SET to change the track.
9 Usable buttons and their functions for the current
selection. Indication here will be changed according to what is currently selected ( in front) on the screen. See “Note on 9.”
Note on 7:
The following information will appear on the display:
• For CD Texts — Disc title, Performer, Genre, Song writer, Composer, Arranger, Message Only recorded information will be shown. If there is no data, “NO DATA” will appear.
• For MDs — Disc title If there is no data, “NO DATA” will appear.
Showing the Disc Information on the TV
Screen
Press TEXT DISPLAY while “CD” or “MD” is selected as the source.
The Disc Information screen appears on the TV.
1
2
3
4 5
Note on 9:
For example, the SET button will be used to start play (PLAY), to go to the next screen (ENTER), and to determine the selection (ENTER).
To exit from the Disc information screen:
Press EXIT.
Notes:
• The on-screen display will disappear in the following cases: – if no operation is done for about 10 minutes.
6
7
8
9
– if you do any operation other than explained in this section.
• To control the MD recorder using the TEXT COMPU LINK remote control system, you have to change the source name shown on the display from “TAPE” to “MD.” (See page 13.)
• Some special characters and marks cannot be displayed correctly.
37
Searching for a Disc (Only for the CD player)
Search for a disc by its performer:
1. Press TEXT DISPLAY while “CD” is selected as the source.
The Disc Information screen appears on the TV.
2. Press % / to move
to “SEARCH,” then
press SET.
The DISC SEARCH screen appears .
3. Press % / to move
to “PERFORMER”,
then press SET.
The PERFORMER SEARCH screen appears.
4. Press % / / @ / # to move in front of the first character of the performer you want to search, then press SET.
To correct the incorrect entry, press % / / @ / # to move
in front of the correct character, then press SET.
Search for a disc by its disc title:
1. Press TEXT DISPLAY while “CD” is selected as the source.
The Disc Information screen appears on the TV.
2. Press % / to move
to “SEARCH,” then
press SET.
The DISC SEARCH screen appears.
3. Press % / fi to move
to “DISC TITLE,
then press SET.
The DISC TITLE SEARCH screen appears.
4. Press % / / @ / # to move in front of the first character of the disc title you want to search, then press SET.
To correct the incorrect entry, press % / / @ / # to move
in front of the correct character, then press SET.
Note:
Symbols such as @, # or $ cannot be available for search.
English
Note:
Symbols such as @, # or $ cannot be available for search.
5. Press SET again.
Disc search starts, then the SEARCH RESULT screen, showing the performers, appears.
6. On the SEARCH RESULT screen, you can do the following:
Changing the indication of the disc information: Press % /
to move
you press @ / #, the disc information alternates between its performer and its disc title.
Starting a disc play and going to the Disc Information
screen (see page 37): Press % / to move disc, then press SET.
Showing unseen disc information (if more than 5 discs are
listed as a result of the search): Press % / until they appear.
Going back to the PERFORMER SEARCH screen: Press
EXIT.
to a searched disc, then press @ / #. Each time
to a searched
5. Press SET again.
Disc search starts, then the SEARCH RESULT screen, showing the disc titles, appears.
6. On the SEARCH RESULT screen, you can do the following:
Changing the indication of the disc information: Press % /
to move
you press @ / #, the disc information alternates between its disc title and its performer.
Starting a disc play and going to the Disc Information
screen (see page 37): Press % / to move disc, then press SET.
Showing unseen disc information (if more than 5 discs are
listed as a result of the search): Press % / until they appear.
Going back to the DISC TITLE SEARCH screen: Press
EXIT .
to a searched disc, then press @ / #. Each time
to a searched
38
Search for a disc by its genre:
English
1. Press TEXT DISPLAY while “CD” is selected as the source.
The Disc Information screen appears on the TV.
2. Press % / to move
to “SEARCH,”
then press SET.
The DISC SEARCH screen appears.
3. Press % / to move
to “GENRE”, then
press SET.
The GENRE SEARCH screen appears.
4. Press % / to move to the genre you want to search, then press SET.
To show the unseen genres, press % / until they appear.
Disc search starts, then the SEARCH RESULT screen, showing the disc titles, appears.
5. On the SEARCH RESULT screen, you can do the following:
Changing the indication of the disc information: Press % /
to move
time you press @ / #, the disc information alternates between its disc title and its performer.
Starting a disc play and going to the Disc Information
screen (see page 37): Press % / to move to a searched disc, then press SET.
Showing unseen disc information (if more than 5 discs are
listed as a result of the search): Press % / until they appear.
Going back to the GENRE SEARCH screen: Press EXIT.
to a searched disc, then press @ / #. Each
Entering the Disc Information
For the CD Player with the disc memory function:
You can use the disc memory function through this receiver. The disc information (its performer, disc title, and music genre) of normal audio CDs will be stored into the memory built in the CD player. For the disc memory function, refer to the manual supplied with your CD player.
• The performer, disc title, and music genre information are usually recorded in a CD Text. However, if a CD Text has no genre information recorded in the disc itself, you can input its music genre by yourself.
Note:
You can enter the TITLE INPUT screens for a CD Text and input its titles. However, you cannot store the titles you have input for a CD Text.
Example: Entering the following information for Disc 1
Performer: “MICHAEL” Disc title: “MY FAVORITE”
1. Press TEXT DISPLAY while “CD” is selected as
the source.
The Disc Information screen appears on the TV.
2. Press % / to move
to “TITLE INPUT,”
then press SET.
The TITLE INPUT: PERFORMER screen appears.
3. Press % / / @ / # to move in front of a
character you want, then press SET to enter the character.
• If the current CD is a CD Text, go to step 5 without entering the performer.
To use the lower case letters, press % / / @ / # to move
to , then press SET.
To use the upper case letters again, press % / / @ / # to move to , then press SET.
39
4. Repeat step 3 until you

finish putting a performer name (up to
32 characters).
To insert a space, press % /
/ @ / # to move
, then press SET.
To correct an incorrect character:
1) Press % / / @ / # to move to + or =, then press SET until the incorrect character is selected.
2) Press % / / @ / # to move to , then press SET to erase the character.
3) Press % / / @ / # to move in front of the correct character, then press SET to enter the correct character.
to
For the MD recorder:
You can write the disc information (disc title and song titles) into the disc. You can only write the song title for the song currently selected.
• If you have the CD-MD combination deck, you can also enter the disc information (its performer, disc title, and its music genre) of normal audio CDs into the memory built in the CD-MD combination deck. (To do this, follow the procedure of “For the CD Player with the disc memory function” on page 39.)
• If you change the disc or song title with more than 32 characters, the characters following 32nd will be erased from the title.
1. Press TEXT DISPLAY while “MD” is selected as
the source.
The Disc Information screen appears on the TV.
English
5. Press % / / @ / # to move MICHAEL (in this
to “DISC 1:
example),” then press SET.
The TITLE INPUT: DISC TITLE screen appears.
6. Enter the disc title, referring to steps 3 and
4.
• If the current CD is a CD
Text, go to the next step without entering the disc title.
7. Press % / / @ / # to move
to “DISC 1:
MY FAVORITE (in this example),” then press SET.
The TITLE INPUT: DISC 1 GENRE screen appears.
8. Press % / to move to the genre you want, then press SET.
The Disc Information screen appears again.
To show the unseen genres, press % / until they appear.
2. Press % / to move to “TITLE INPUT,”
then press SET.
The DISC TITLE INPUT screen appears.
3. Enter the title, referring
to steps 3 and 4 of “For the CD Player with the disc memory function” on page 39.
• You can enter up to 32 characters for the disc title.
4. Press % / / @ / # to move
to the disc title you have just entered, then press SET.
The disc title is stored into the memory, and the SONG TITLE INPUT screen for the currently selected song appears.
• You can enter a song title for the song currently selected
(indicated in yellow on the TV screen).
5. Enter the song title, referring to steps 3 and 4 of “For the CD Player with the disc memory function” on page 39.
• You can enter up to 32 characters for the song title.
6. Press % / / @ / # to move to the song title you have just entered, then press SET.
The song title is stored into the memory, and the Disc Information screen appears again.
40

AV COMPU LINK Remote Control System

The AV COMPU LINK remote control system allows you to operate JVC video components (TV, VCR, and DVD player) through the receiver.
English
To use this remote control system, you need to connect the video components you want to operate, following the diagrams below and the procedure on the next page.
CONNECTIONS 1:
VHS
AV
COMPU LINK
VCR
DVD player
DVD
AV
COMPU LINK
AV
COMPU LINK
CONNECTIONS 2:
CASE 1: If the components are equipped with the S-video
terminals
TV
CAUTION:
The AV COMPU LINK remote control system cannot control the DBS tuner connected to the TV SOUND/DBS jacks.
If the AV COMPU LINK terminal on the TV is “RECEIVER/AMP”
AV
RECEIVER/AMP
EX
(VCR)
COMPU LINK
RECEIVER/
AMP
Notes:
• When connecting only the VCR or DVD player to this
If the AV COMPU LINK terminal on the TV is “AV COMPU LINK EX”
AV
EX
COMPU LINK
receiver, connect it directly to the receiver using cable with the monaural mini-plugs.
• Refer also to the manuals supplied with your video components.
CASE 2: If the components are not equipped with the S-
video terminals
DO NOT use these video terminals.
(PLAY)
(REC)
IN
MONITOR
DVD
OUT
VCR
OUT
VIDEO
VIDEO S-VIDEO
DVD player
DVD
VCR
S-VHS
TV
To Video input 1
CASE 3: If only the VCR is equipped with the S-video
terminal
DO NOT use these video terminals.
TV
To Video input 1
To Video input 2
(PLAY)
DVD
OUT (REC)
VCR
IN
MONITOR
OUT
VIDEO
VIDEO S-VIDEO
DVD player
DVD
VCR
S-VHS
DO NOT use these video terminals.
VIDEO
(PLAY)
MONITOR
(REC)
IN
DVD
OUT
VCR
OUT
VIDEO S-VIDEO
DVD player
DVD
VCR
VHS
TV
To Video input 2
CASE 4: If only the DVD player is equipped with the S-
video terminal
DO NOT use these video terminals.
VIDEO
(PLAY)
MONITOR
(REC)
IN
DVD
OUT
VCR
OUT
VIDEO S-VIDEO
DVD player
DVD
VCR
VHS
To Video input 2
To Video input 1
TV
41
1. If you have already plugged your VCR, DVD player, TV, and this receiver into the AC outlets, unplug their AC power cords first.
2. Connect your VCR, DVD player, TV, and this receiver, using the cables with the monaural mini­plugs (not supplied).
• See “CONNECTIONS 1” on the previous page.
3. Connect the audio input/output jacks on VCR, DVD player, TV, and this receiver using the cables with RCA pin plug.
• See pages 6 and 7.
4. Connect the video input/output jacks on VCR, DVD player, TV, and this receiver, using the cables with RCA pin plug or with S-video plug.
• See “CONNECTIONS 2” on the previous page.
5. Plug the AC power cords of the components into the AC outlets.
6. When turning on the TV for the first time after the AV COMPU LINK connection, turn the TV volume to the minimum using the TV volume control on the TV.
7. Turn on the other connected components first, then turn on this receiver.
• When turning on the VCR, use the remote control supplied
with this receiver (press VCR
The AV COMPU LINK remote control system allows you to use the five basic functions listed below.
Remote Control of the TV, DVD player, and VCR Using This Remote Control
See page 45 for details.
For the DVD player and the VCR:
• Aim the remote control directly at the remote sensor on each
component. For the TV having AV COMPU LINK terminal “RECEIVER/ AMP”:
• Aim the remote control directly at the remote sensor on the
receiver. For the TV having AV COMPU LINK terminal “AV COMPU LINK EX”:
• Aim the remote control directly at the remote sensor on the TV.
One-Touch Video Play
Simply by inserting a video cassette without its safety tab into the VCR, you can enjoy the video playback without setting other switches manually. The receiver automatically turns on and changes the source to “VCR.” The TV automatically turns on and changes the input mode to the position so that you can view the playback picture. When you insert a video cassette with its safety tab, press the play
33
(
3) button on the VCR or on the remote control. So, you can get the
33
same result.
).
One-Touch DVD Play
Simply by starting playback on the DVD player, you can enjoy the DVD playback without setting other switches manually.
When the DVD player is connected through the analog input jacks on this receiver (and analog input is selected), the receiver automatically turns on and changes the source to “DVD” or “DVD MULTI.”
When the DVD player is connected through the digital input terminal on this receiver (and digital input is selected), the receiver automatically turns on and changes the source to “DVD DIGITAL.”
The TV automatically turns on and changes the input mode to the position so that you can view the playback picture.
Automatic Selection of TV’s Input Mode
• When you select “TV SOUND” (or “TV DIGITAL”) as the source
to play on the receiver, the TV automatically changes the input mode to the TV tuner so that you can watch TV.
• When you select “DVD” (or “DVD DIGITAL”), “DVD MULTI,”
“VCR,” or “DBS” (or “DBS DIGITAL”) as the source to play on the receiver, the TV automatically changes the input mode to the appropriate position (either Video Input 1 or Video Input 2) so that you can view the playback picture.
Note:
When you select “TV SOUND” (or “TV DIGITAL”) as the source on the receiver, you cannot see the menu on the TV screen since the AV COMPU LINK remote control system automatically changes the TV’s input mode to the TV tuner. If you do not mind stopping listening to the TV sounds, you can then show the on-screen displays after changing the TV’s input mode to the appropriate position (either Video Input 1 or Video Input 2) the receiver is connected to.
Automatic Power On/Off
The TV, VCR, and DVD player turn on and off along with the receiver. When you turn on the receiver;
• If the previously selected source is “VCR,” the TV and VCR will
turn on automatically.
• If the previously selected source is “TV SOUND” (or “TV
DIGITAL”) or “DBS” (or “DBS DIGITAL”), only the TV will turn on automatically.
• If the previously selected source is “DVD” (or “DVD DIGITAL”)
or “DVD MULTI,” the TV and DVD player will turn on
automatically. When you turn off the receiver, the TV, VCR and the DVD player will turn off.
Note:
If you turn off the receiver while recording on the VCR, the VCR will not turn off, but continue recording.
English
42

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.
English
Operating Audio Components
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page 35) in addition to the connections using cables with RCA pin plugs (see pages 5 and 6).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel or the menu function to choose a source, the remote control will not operate that source. To operate a source with the remote control, the source must be selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 13.)
• Refer also to the manuals supplied with your components.
TV/CATV/DBS
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
SURROUND
ON/OFF
TEST REAR-L
SURROUND
MODE
CD-DISC
EFFECT REAR-R
7
SOUND
SEA MODE
10
RETURN
MENU
EXIT
CHANNEL VOLUMETV VOL
TV/VIDEO
VCR
/REW
DOWN UP
REC
RM-SRX7001P REMOTE CONTROL
VCR
ANALOG/DIGITAL
SLEEP
CENTER
123
MENUMENU
456
ENTERENTER
/P
89
SUBWOOFER
+10
0
FM MODE
100+
AUDIO/ TV/VCR
CATV/DBS
SET
TEXT
DISPLAY
TAPE/MD
MUTING
CONTROL
FF/
PLAY
TUNING STOP PAUSE
AUDIO/ TV/VCR
CATV/DBS
Check to see if the remote control mode selector is set to the correct position.
To operate the audio system, TVs, VCRs, and DVD players, set it to
“AUDIO/TV/VCR.”
Tuner
You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):
FM/AM: Alternates between FM and AM.
After pressing FM/AM (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations:
1 – 10, +10: Selects a preset channel number directly.
For channel number 5, press 5. For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.
TUNING UP/TUNING DOWN:
Tunes into stations.
FM MODE: Changes the FM reception mode.
Sound control section (Amplifier)
You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):
SURROUND ON/OFF: Turns on or off the Surround modes —
Dolby Pro Logic, Dolby Digital, DTS Digital Surround and MPEG Multichannel.
SURROUND MODE: Selects the DSP modes.
After pressing SOUND (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations:
SEA MODE: Changes the SEA modes. SUBWOOFER – / +: Adjusts the subwoofer output level. CENTER – / +: Adjusts the center speaker output level. REAR•L – / +: Adjusts the left rear speaker output level. REAR•R – / +: Adjusts the right rear speaker output level. EFFECT: Selects the effect level. TEST: Turns on or off the test tone output.
Note:
After adjusting sounds, press the corresponding source selecting button or CD-DISC to operate your target source by using the 10 keys; otherwise, the 10 keys cannot be used for operating your target source.
CD player
After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the CD player:
PLA Y: Starts playing.
44
4: Returns to the beginning of the current (or
44
previous) track.
¢¢
¢: Skips to the beginning of the next track.
¢¢
STOP: Stops playing. P AUSE: Pauses playing. To release it, press PLAY. 1 – 10, +10: Selects a track number directly.
For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 30, press +10, +10, then 10.
43
CD player-changer
After pressing CD-DISC (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a CD player-changer:
Cassette deck
After pressing TAPE/MD or TAPE/MD CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a cassette deck:
English
PLA Y: Starts playing.
44
4: Returns to the beginning of the current (or previous)
44
track.
¢¢
¢: Skips to the beginning of the next track.
¢¢
STOP: Stops playing. P AUSE: Pauses playing. To release it, press PLAY. 1 – 6, 7/P: Selects the number of a disc installed in a CD
player-changer.
After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the CD player-changer: 1 – 10, +10: Selects a track number directly.
For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 30, press +10, +10, then 10.
Turntable
After pressing PHONO (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a turntable:
PLAY : Starts playing. STOP: Stops operations.
PLA Y: Starts playing.
11
1: Fast winds the tape from right to left.
11 ¡¡
¡: Fast winds the tape from left to right.
¡¡
STOP: Stops operations. P AUSE: Pauses playing. To release it, press PLAY.
REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
MD recorder
After pressing TAPE/MD or TAPE/MD CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the MD recorder:
PLA Y: Starts playing. 4: Returns to the beginning of the current (or previous)
track.
¢: Skips to the beginning of the next track.
STOP: Stops playing. P AUSE: Pauses playing. To release it, press PLAY.
REC: Press this button with the PLAY button to start
recording.
Press this button with the PAUSE button to enter
recording pause.
Note:
You can use either TAPE/MD button or the TAPE/MD CONTROL button to activate the buttons listed above. If you press TAPE/MD, the playing source also changes. On the other hand, if you press TAPE/ MD CONTROL, the playing source does not change.
44
Operating Video Components
English
IMPORTANT:
To operate JVC’s video components using this remote control:
• You need to connect JVC video components through the AV COMPU LINK terminals (see page 41) in addition to the connections using cables with RCA pin plugs (see pages 6 and 7).
• Some JVC VCRs can accept two types of the control signals — remote code “A” and “B.” Before using this remote control, make sure that the remote control code of the VCR is set to code “A.”
• When using the remote control: – For the DVD player and VCR operations, aim the remote
control directly at the remote sensor on each component, not on the receiver.
– For the TV operations:
7 If the TV has the AV COMPU LINK terminal
“RECEIVER/AMP,” aim the remote control directly at the remote sensor on the receiver.
7 If the TV has the AV COMPU LINK terminal “AV
COMPU LINK EX,” aim the remote control directly at the remote sensor on the TV.
VCR
You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):
VCR : Turns on or off the VCR.
After pressing VCR or VCR CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:
1 – 9, 0: Selects the TV channels on VCR. PLAY : Starts playing.
1: Rewinds a tape. ¡: Fast winds a tape.
STOP: Stops operations. PAUSE: Pauses playing. To release it, press PLAY.
REC: Press this button with the PLAY button to start
recording. Press this button with the PAUSE button to enter recording pause.
CHANNEL +/–: Changes the TV channels on the VCR.
Note:
You can use either VCR button or the VCR CONTROL button to activate the buttons listed above. If you press VCR, the playing source also changes. On the other hand, if you press VCR CONTROL, the playing source does not change.
TV/CATV/DBS
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
ANALOG/DIGITAL
SURROUND
ON/OFF
SURROUND
MODE
CD-DISC
SOUND
MENU
EXIT
TV/VIDEO
/REW
DOWN UP
REC
RM-SRX7001P REMOTE CONTROL
CENTER
123
MENUMENU
TEST REAR-L
456
ENTERENTER
EFFECT REAR-R
/P
89
7
SEA MODE
SUBWOOFER
10
0
RETURN
FM MODE
SET
CHANNEL VOLUMETV VOL
TAPE/MD
VCR
CONTROL
PLAY
TUNING STOP PAUSE
CATV/DBS
FF/
VCR
SLEEP
+10
100+
AUDIO/ TV/VCR
TEXT
DISPLAY
MUTING
AUDIO/ TV/VCR
CATV/DBS
Check to see if the remote control mode selector is set to the correct position.
To operate the audio system, TVs, VCRs, and DVD players, set it to
“AUDIO/TV/VCR.”
DVD player
After pressing DVD or DVD MULTI (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a DVD player:
PLA Y: Starts playing.
4: Returns to the beginning of the current (or previous) track. ¢: Skips to the beginning of the next track.
STOP: Stops playing. P AUSE: Stops playing temporarily. To release it, press PLAY.
After pressing DVD or DVD MULTI, these buttons can be used for the DVD menu operations.
Note:
For detailed menu operations, refer to the instructions supplied with the discs or the DVD player.
TEST REAR-L
456
CENTER
23
MENUMENU
ENTERENTER
REAR-R
8
TV
You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”):
TV/CATV/DBS :Turns on or off the TV. TV VOL +/–: Adjusts the volume. TV/VIDEO: Sets the input mode (either TV or VIDEO).
45
After pressing TV/DBS (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a TV:
CHANNEL +/–: Changes the channels. 1 – 9, 0, 100+: Selects the channels. RETURN: Alternates between the previously selected
channel and the current channel.

Operating Other Manufacturers’ Video Equipment

This remote control supplied with the receiver can transmit control signals for other manufacturers’ VCRs, TVs, CATV converters and DBS tuners. By changing the transmittable signals from preset ones to the other manufacturers’, you can operate the other manufacturer’s components using this remote control.
When operating the other manufacturers’ components, refer also to the manuals supplied with them. To operate these components with the remote control, first you need to set the manufacturer’s code each for VCR, TV, CATV converters and DBS tuners.
TV/CATV/DBS
DVD DVD MUILTI CD TAPE/MD
TV/DBS PHONO FM/AM
VCR
SURROUND
ON/OFF
TEST REAR-L
SURROUND
MODE
CD-DISC
EFFECT REAR-R
7
SOUND
SEA MODE
10
RETURN
MENU
EXIT
CHANNEL VOLUMETV VOL
VCR
ANALOG/DIGITAL
SLEEP
CENTER
123
MENUMENU
456
ENTERENTER
/P
89
SUBWOOFER
+10
0
FM MODE
100+
AUDIO/ TV/VCR
CATV/DBS
SET
TEXT
DISPLAY
AUDIO/ TV/VCR
CATV/DBS
To change the transmittable signals for operating another manufacturer’s TV
1. Set the remote control mode to “AUDIO/TV/ VCR.”
2. Press and hold TV/CATV/DBS
.
3. Press TV/DBS.
4. Enter manufacturer’s code (three digits) using buttons 1 – 9, and 0.
See the list on pages 48 and 49 to find the code. Examples: For a JVC product, press 0, 3, then 6.
For a Sony product, press 0, 0, then 0.
5. Release TV/CATV/DBS .
The following buttons can be used for operating the TV (with the remote control mode selector set to “AUDIO/TV/VCR”):
TV/CATV/DBS TV VOL +/–: Adjusts the volume. TV/VIDEO: Sets the input mode (either TV
After pressing TV/DBS (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on a TV:
: Turns on and off the TV.
or VIDEO).
English
VCR
TV/VIDEO
TAPE/MD
CONTROL
/REW
PLAY
TUNING
DOWN UP
STOP PAUSE
REC
RM-SRX7001P REMOTE CONTROL
MUTING
FF/
Check to see if the remote control mode selector is set to the correct position.
To operate the audio system, TVs, and VCRs,
set it to “AUDIO/TV/VCR.”
CHANNEL +/–: Changes the channels. 1 – 10, 0, 100+ (+10): Selects the channels.
The 100+ (+10) button will function as the ENTER button if your TV requires pressing ENTER after selecting a channel number.
To operate the CATV converter, set it to “CATV/
DBS.”
Note:
Refer to the manual supplied with your TV.
6. Try to operate your TV by pressing TV/CATV/ DBS
When your TV turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
.
46
To change the transmittable signals for operating a CATV converter or DBS tuner
English
To change the transmittable signals for operating another manufacturer’s VCR
1. Set the remote control mode to “CATV/DBS.”
2. Press and hold TV/CATV/DBS
.
3. Press TV/DBS.
4. Enter manufacturer’s code (three digits) using buttons 1 – 9, and 0.
See the list on pages 49 and 50 to find the code. Examples: For a Toshiba product, press 0, 0, then 0.
For a Samsung product, press 7, 0, then 2.
5. Release TV/CATV/DBS .
After setting the remote control mode selector to “CATV/DBS,” you can perform the following operations on the CATV convertor or on the DBS tuner:
TV/CATV/DBS : Turns on and off the CATV converter
or the DBS tuner.
CHANNEL +/–: Changes the channels. 1 – 10, 0, 100+ (+10): Selects the channels.
The 100+ (+10) button will function as the ENTER button if your equipment requires pressing ENTER after selecting a channel number.
Note:
Refer to the manual supplied with your CATV converter or DBS tuner.
6. Try to operate your CATV converter or DBS tuner by pressing TV/CATV/DBS
When your CATV converter or DBS tuner turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of CATV converter or DBS tuner, try each one until the correct
one is entered.
.
1. Set the remote control mode to “AUDIO/TV/ VCR.”
2. Press and hold VCR
.
3. Press VCR.
4. Enter manufacturer’s code (three digits) using buttons 1 – 9, and 0.
See the list on pages 50 and 51 to find the code. Examples: For a JVC product, press 0, 0, then 8.
For an NEC product, press 0, 3, then 8.
5. Release VCR .
The following button can be used for operating the VCR (with the remote control mode selector set to “AUDIO/TV/VCR”):
VCR
After pressing VCR or VCR CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”), you can perform the following operations on the VCR:
CHANNEL +/–: Changes the TV channels on the 1 – 10, 0, 100+ (+10): Selects the TV channels.
PLAY: Starts playback.
1: Rewinds a video tape. ¡: Fast winds a video tape.
STOP: Stops operation. PAUSE: Pauses. REC: Starts recording or enters recording
Notes:
• Refer to the manual supplied with your VCR.
• You can use either VCR button or the VCR CONTROL button to
activate the buttons listed above. If you press VCR, the playing source also changes. On the other hand, if you press VCR CONTROL, the playing source does not change.
: Turns on and off the VCR.
VCR.
The 100+ (+10) button will function as the ENTER button if your VCR requires pressing ENTER after selecting a channel number.
pause.
6. Try to operate your VCR by pressing VCR .
When your VCR turns on or off, you have entered the correct code.
If there are more than one code listed for your brand of VCR, try each one until the correct one is entered.
47
Manufacturers’ codes for TV
A-Mark 003
Acura 009 Admiral 093 Aiko 092 Akai 030, 208 Akura 264 Alaron 216 Alba 009, 036, 037 Amstrad 009, 037 Anam 003, 004, 009, 068, 161, 250, 425, 426 Anam National 161, 250, 425 Anitech 009, 068 AOC 003, 030 Arcam 216 Archer 003 Audinac 391 Audiosonic 037 Audiovox 003, 092, 451 Basic Line 009 Baur 037, 535, 554 Bell & Howell 154 Beon 037 Blaupunkt 535, 554 Britannia 216 Broksonic 003, 426 Bush 009, 036, 037 Candle 030, 186 Carnivale 030 Carrefour 036 Carver 054, 170 Cascade 009 Cathay 037 CCE 037 Celebrity 000 Centurion 037 Cimline 009 Cineral 092, 451 Citizen 030, 039, 060, 092, 186 Clarivox 037 Contec 009, 036, 216 Continental Edison 489 Craig 161 Crosley 054 Crown 009, 037, 039 CS Electronics 216 Curtis Mathes 030, 039, 047, 054, 060, 093, 145, 154,
166, 451
Daewoo 009, 037, 039, 066, 092, 154, 391, 402,
451 Dansai 037 Dayton 009 De Graaf 208 Decca 037 Denon 145 Dixi 004, 009, 037 ECE 037 Ectec 391 Electroband 000 Electrohome 409 Elin 037 Elta 009 Emerson 039, 154, 178 Envision 030 Erres 037 Etron 009, 283 Ferguson 037, 560 Fidelity 216 Finlandia 208
Finlux 037 Firstline 009, 216 Fisher 154, 208 Formenti 037 Fortress 093 Frontech 264 Funai 264, 342 GE 047, 093, 178, 451 GEC 037 Geloso 009 General 186 Gibralter 030 GoldStar 001, 002, 030, 037, 039, 178, 283, 409,
457, 467 Goodmans 036, 037 Gradiente 053, 170 Granada 037, 208, 502 Grundig 037, 535, 554 Hallmark 178 Hanseatic 037 Harman/Kardon 054 Harvard 068 HCM 009 Hinari 009, 036, 037, 283 Hitachi 036, 145, 409, 576 Huanyu 216 Hypson 037, 264 ICE 264 Indiana 037 Infinity 054 Inkel 571 Interbuy 068 Interfunk 037 Intervision 037, 068, 264 ITT 283 JBL 054 JCB 000 JEC 502 JVC 036, 053, 069, 160 Kaisui 009, 216 Kamp 216 Kawasho 216 Kendo 037 Kenwood 030 Kingsley 216 Korpel 037 Koyoda 009 KTV 030, 039 Leyco 037, 264 Liesenk & Tter 037 Logik 001 LXI 047, 054, 154, 156, 178 M Electronic 009, 037, 068 Magnavox 030, 036, 054, 186 Manesth 264 Marantz 030, 037, 054 Mark 037 Maruman 391 Matsui 009, 036, 037, 208 Matsushita 250 Mediator 037 Megatron 003, 145, 178 Memorex 009, 150, 154, 178, 250 Metz 535 MGA 030, 150, 178 Midland 039, 047 Minerva 535, 554 Mitsubishi 036, 093, 150, 178, 535
English
48
Mivar 216 Motorola 093
English
MTC 030, 060, 216 Multitech 009, 216 NAD 156, 166, 178 National 226 NEC 030, 036, 170 Neckermann 037, 554 NEI 037 Nicamagic 216 Nikkai 037, 216, 264 Nikko 030, 092, 178 Nisato 391 Nordmende 560 NTC 092 Optimus 154, 166, 250 Optonica 093 Orion 037 Osaki 264 Otto Versand 036, 037, 535, 554 Panama 264 Panasonic 161, 226, 250 Pathe Cinema 216 Pausa 009 Penney 002, 003, 030, 039, 047, 060, 156, 178 Philco 030, 054, 145 Philips 037, 054, 554 Phonola 037 Pilot 030, 039 Pioneer 166 Portland 039, 092 Profex 009 Proscan 047 Protech 009, 037, 264 Proton 003, 178 Quasar 250 Quelle 037, 252, 535, 554 Questa 036 R-Line 037 Radio Shack 030, 039, 047, 154, 178, 409 Radiola 037 Rank Arena 036 RCA 047, 090, 093 Realistic 030, 039, 154, 178 Revox 037 Rex 264 Rhapsody 216 Roadstar 009, 264 Runco 030 Saisho 009, 264 Sampo 030, 039 Samsung 009, 030, 037, 039, 060, 090, 178, 264,
427 Samsux 039 Sandra 216 Sansei 451 Sanyo 036, 154, 208, 376, 424 SBR 037 Schneider 037 Scotch 178 Scott 178 Sears 047, 054, 154, 156, 178 SEG 036, 264 Semp 156 Sentra 283 Sharp 036, 039, 093, 256 Siemens 037, 535, 554 Silver 036
Simpson 186 Sky-Worth 037 Sonitron 208 Sonoko 009, 037 Sonolor 208 Sontec 037 Sony 000, 036 Soundesign 178, 186 Soundwave 037 Spectricon 003 Standard 009 SuperTech 216 Supreme 000 Sylvania 030, 054 Sysline 037 Tandy 093 Tashiko 036 Tatung 003, 037 Technics 250 Techwood 003 Teknika 039, 054, 060, 092, 150, 186 Telefunken 252 Teletech 009 Teleton 186 Texet 216 Thomson 489, 560 Thorn 037, 535 TMK 178 Toshiba 036, 060, 154, 156, 241, 502 Totevision 039 Ultra 391 Universum 037, 264, 535 Vector Research 030 Vestel 037 Victor 036, 053, 160, 250, 376 Vidikron 054 Vidtech 036, 178 Wards 030, 054, 178 Watson 037 Wega 036 White Westinghouse 037, 216 Yamaha 030 Yoko 037, 264 Zenith 092 Zonda 003
Manufacturers’ codes for CATV converters
ABC 008 Daeryung 008 GoldStar 838 LG Alps 779 Memorex 000 Now 776 Panasonic 000 Paragon 000 Pulsar 000 Quasar 000 Runco 000 Samsung 702 Scientific Atlanta 008 Seawoo 780 TongKook 777, 840 Toshiba 000 Zenith 000
49
Manufacturers’ codes for DBS tuner
Cyrus 200 Dae Young 735 DNT 200 DX Antenna 752 Kathrein 200 Marantz 200 Panasonic 739 Pantech 747 Philips 200 Radiola 200 RFT 200 Samsung 773 Sony 661 Toshiba 486 Ventana 200
Manufacturers’ codes for VCR
Admiral 048 Adventura 000 Aiko 278 Aiwa 000, 037 Akai 041, 061, 281, 288 Akiba 072 Alba 020, 072, 278 Ambassador 020 Amstrad 000, 278 Anam 037, 162, 226, 240, 278, 553 Anam National 162, 226 Anitech 072 ASA 037, 081 Asha 240 Asuka 037 Audiovox 037 Baird 000, 041, 104 Basic Line 020, 072, 278 Beaumark 240 Bell & Howell 104 Blaupunkt 034, 162, 195, 226, 227 Brandt 187, 320 Brandt Electronic 041 Bush 072, 278 Calix 037 Capehart 020 Carver 081 Catron 020 CCE 072, 278 CGE 000 Cimline 072 Cineral 278 Citizen 037, 278 Clatronic 020 Colt 072 Condor 020 Craig 037, 072, 240 Crown 020, 072, 278 Curtis Mathes 041, 162 Cybernex 240 Cyrus 081 Daewoo 020, 045, 046, 278, 368 Dansai 072 Daytron 020 De Graaf 042, 166 Decca 000, 081 Denon 042
Dual 041 Dumont 000, 081, 104 Dynatech 000 Elbe 038 Elcatech 072 Electrohome 037 Electrophonic 037 Emerex 032 Emerson 000, 037, 043, 061, 278 ESC 240, 278 Ferguson 041, 320 Fidelity 000 Finlandia 081, 104 Finlux 000, 042, 081, 104 Firstline 037, 043, 045, 072 Fisher 046, 104 Frontech 020 Fuji 033 Funai 000 Garrard 000 GE 048, 240 GEC 081 General 020, 052 Go Video 432 GoldHand 072 GoldStar 037, 038, 225, 471 Goodmans 000, 020, 037, 062, 072, 278 Gradiente 000, 008 Graetz 041, 104, 240 Granada 046, 081, 104 Grandin 000, 037, 072 Grundig 072, 081, 195, 226 Hanseatic 037 Harley Davidson 000 Harman/Kardon 038, 081 Harwood 072 HCM 072 Headquarter 046 Hinari 072, 240 Hitachi 000, 041, 042, 166, 235, 240 Hypson 072 Imperial 000 Interfunk 081 ITT 041, 046, 104, 240, 384 ITV 037, 278 Jensen 041 JVC 008, 041, 067, 384 Kaisui 072 KEC 037, 278 Kenwood 038, 041, 067, 384 KLH 072 Kodak 037 Korpel 072 Lenco 278 Leyco 072 Lloyd’s 000 Loewe 037, 081, 162 Logik 072, 240 Luxor 043, 046, 048, 062, 104 LXI 037 M Electronic 000 Magnasonic 278 Magnavox 000, 081 Magnin 240 Manesth 045, 072 Marantz 062, 081 Marta 037 Matsushita 162, 227
English
50
English
Melectronic 038 Memorex 000, 037, 046, 048, 104, 162, 240 Memphis 072 Metz 037, 162, 195, 227 MGA 043, 061, 240 MGN Technology 240 Minerva 195 Minolta 042 Mitsubishi 043, 048, 061, 067, 081, 173, 196 Motorola 048 MTC 000, 240 Multitech 000, 072 Murphy 000 NAD 058 National 226 NEC 038, 040, 041, 067, 104, 370 Neckermann 081 Nesco 072 Nikko 037 Nikon 034 Noblex 240 Nokia 041, 046, 104, 240 Nordmende 041, 320, 384 Oceanic 000, 041 Olympus 226 Optimus 037, 048, 058, 104, 162, 432 Optonica 062 Osaki 000, 037, 072 Otto Versand 081 Palladium 037, 041, 072 Panasonic 162, 225, 226, 227, 367 Pathe Marconi 041 Penney 037, 038, 040, 042, 240 Pentax 042 Perdio 000 Philco 038 Philips 062, 081, 384 Phonola 081 Pilot 037 Pioneer 058, 067, 081, 162, 235 Portland 020 Profitronic 240 Proline 000 Protec 072 Pye 081 Quarter 046 Quartz 046 Quasar 162 Quelle 081 Radio Shack 000, 037 Radiola 081 Radix 037 Randex 037 RCA 042, 048, 240 Realistic 000, 037, 046, 048, 062, 104 Rex 041, 384 Ricoh 034 Roadstar 037, 072, 240, 278 Saba 041, 320, 384 Salora 043, 046 Samsung 045, 240, 426, 432 Sanky 048 Sansui 000, 041, 067 Sanyo 046, 104, 240, 368, 369 SBR 081 Schaub Lorenz 000, 041, 104 Schneider 000, 072, 081 Scott 043, 045
Sears 000, 037, 042, 046, 104 SEG 240 SEI 081 Seleco 041 Semp 045 Sentra 020 Sharp 048, 062, 363 Shintom 072, 104 Shogun 240 Siemens 037, 081, 104, 195 Silva 037 Singer 045, 072 Sinudyne 081 Solavox 020 Sonolor 046 Sontec 037 Sony 000, 032, 033, 034 STS 042 Sunstar 000 Suntronic 000 Sylvania 000, 043, 081 Symphonic 000 Tashiko 000 Tatung 000, 041, 081 Teac 000, 041 Tec 020 Technics 162, 226 Teknika 000, 037, 052 Teleavia 041 Telefunken 041, 187, 320, 384 Tenosal 072 Tensai 000 Thomas 000 Thomson 041, 320, 384 Thorn 041, 104 TMK 240 Toshiba 041, 043, 045, 081, 366, 384 Totevision 037, 240 Uher 240 Unitech 240 Universum 000, 037, 081, 195, 240 Vector 045 Vector Research 038, 040 Victor 008, 041, 067, 384 Video Concepts 040, 045, 061 Videosonic 240 Wards 000, 042, 048, 062, 072, 081, 240 White Westinghouse 278 XR-1000 000, 072 Yamaha 038 Yamishi 072 Yokan 072 Yoko 020, 240 Zenith 000, 033, 034
Manufacturers’ codes listed on pages 48 to 51 are subject to change without notice. If they are changed, this remote control cannot operate the equipment.
51

Troubleshooting

Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC service center.
PROBLEM
POSSIBLE CAUSE
SOLUTION
English
The display does not light up.
No sound from speakers.
Sound from one speaker only.
Continuous hiss or buzzing during FM reception.
Occasional cracking noise during FM reception.
The power cord is not plugged in.
Speaker signal cables are not connected.
The SPEAKERS 1 and 2 buttons are not set correctly.
An incorrect source is selected.
Muting is activated.
Speaker signal cables are not connected properly.
The balance is set to one extreme.
Incoming signal is too weak.
The station is too far away.
An incorrect antenna is used.
Antennas are not connected properly.
Ignition noise from automobiles.
Plug the power cord into an AC outlet.
Check speaker wiring and reconnect if necessary.
Press SPEAKERS 1 and 2 correctly.
Select the correct source.
Press MUTING to cancel the mute.
Check speaker wiring and reconnect if necessary.
Adjust the balance properly (see page 13).
Connect an outdoor FM antenna or contact your dealer.
Select a new station.
Check with your dealer to be sure you have the correct antenna.
Check connections.
Move the antenna farther from automobile traffic.
No colors on the on-screen display.
Howling during record playing.
“OVERLOAD” starts flashing on the display.
Remote control does not work.
The color system of the connected TV is not PAL.
Your turntable is too close to speakers.
Speakers are overloaded because of high volume.
Speakers are overloaded because of short circuit of speaker terminals.
The remote control mode selector is not set correctly.
There is an obstruction in front of the remote sensor on the receiver.
Batteries are weak.
Connect a PAL- or multi-color system TV.
Move speakers away from the turntable.
1. Press STANDBY/ON panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the volume.
Press STANDBY/ON then check the speaker wiring. If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again. If speaker wiring is not short-circuited, contact your dealer.
Set the selector correctly either to “AUDIO/ TV/VCR” or to “CATV/DBS.”
Remove the obstruction.
Replace batteries.
on the front
on the front panel,
52
Amplifier
English
Audio

Specifications

Output Power
At Stereo operation: Front channels: 100 W* per channel, min. RMS, both channels driven into 8 at
1 kHz with no more than 0.9% total harmonic distortion. (IEC268-3/DIN)
At Surround operation: Front channels: 100 W* per channel, min. RMS, driven into 8 Ω at 1 kHz with no
more than 0.8% total harmonic distortion.
Center channel: 100 W*, min. RMS, driven into 8 at 1 kHz, with no more than
0.8% total harmonic distortion.
Rear channels 100 W* per channel, min. RMS, driven into 8 Ω at 1 kHz, with no
more than 0.8% total harmonic distortion.
(* Measured on AC 110 V, 127 V, 220 V and 240 V)
Audio Input Sensitivity/Impedance (1 kHz): PHONO (MM): 2.5 mV/47 k
CD, TAPE/MD, TV SOUND/DBS, VCR, DVD:
200 mV/47 k
Audio Input (DIGITAL IN)* : Coaxial: DIGITAL 1 (DVD): 0.5 V(p-p)/75
Optical: DIGITAL 2 (CD), DIGITAL 3 (TV):
–21 dBm to –15 dBm (660 nm ±30 nm)
*Corresponding to Linear PCM, Dolby Digital, DTS Digital Surround and MPEG
Multichannel (with sampling frequency — 32 kHz, 44.1 kHz, 48 kHz).
Audio Output Level: TAPE/MD, VCR: 200 mV
Digital output: Optical: DIGITAL OUTPUT
Signal wave length: 660 nm Output level: –21 dBm to –15 dBm
Signal-to-Noise Ratio (’66 IHF/DIN): PHONO: 70 dB/66 dB (at REC OUT)
CD, TAPE/MD, TV SOUND/DBS, VCR, DVD:
87 dB/67 dB
Frequency Response (8 Ω): PHONO: 20 Hz to 20 kHz (±1 dB)
CD, TAPE/MD, TV SOUND/DBS, VCR, DVD:
20 Hz to 20 kHz (±1 dB)
RIAA Phono Equalization: ±1.0 dB (20 Hz to 20 kHz)
Bass boost: +6 dB ±1.0 dB at 100 Hz (Volume control at –30 dB)
SEA: Center frequencies: 100 Hz, 1 kHz, 10 kHz
Control range: ±10 dB ±2 dB
Video
53
Video Input Sensitivity/Impedance:
Composite video: TV SOUND/DBS, VCR, DVD: 1 V(p-p)/75
S-video: TV SOUND/DBS, VCR, DVD: (Y: luminance): 1 V(p-p)/75
(C: chrominance, burst): 0.286 V(p-p)/75
Video Output Level:
Composite video: VCR, MONITOR OUT: 1 V(p-p)/75
S-video: VCR, MONITOR OUT: (Y: luminance): 1 V(p-p)/75
(C: chrominance, burst): 0.286 V(p-p)/75
Synchronization: Negative
Signal-to-Noise Ratio: 45 dB
On-Screen Color System: PAL
FM tuner (IHF)
Tuning Range: 87.50 MHz to 108.00 MHz
Usable Sensitivity: Monaural: 12.8 dBf (1.2 µV/75 Ω)
50 dB Quieting Sensitivity: Monaural: 21.3 dBf (3.2 µV/75 Ω)
Stereo: 41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted): Monaural: 78 dB at 85 dBf
Stereo: 73 dB at 85 dBf
Total Harmonic Distortion: Monaural: 0.4% at 1 kHz
Stereo: 0.6% at 1 kHz
Stereo Separation at REC OUT: 35 dB at 1 kHz
Alternate Channel Selectivity: 45 dB: (±400 kHz)
Frequency Response: 30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM tuner
Tuning Range: 531 kHz to 1 602 kHz (at 9 kHz intervals)
530 kHz to 1 600 kHz (at 10 kHz intervals)
Usable Sensitivity: Loop antenna 400 µV/m
Signal-to-Noise Ratio 50 dB (100 mV/m)
General
Power Requirements: AC 110 V/127 V/220 V/230 V – 240 V ,
adjustable with the voltage selector, 50 Hz/60 Hz
Power Consumption: 200 W(at operation)
5 W (in standby mode)
Dimensions (W x H x D): 435 mm x 157 mm x 412.5 mm
Mass: 11. 3kg
English
Designs & specifications are subject to change without notice.
54
Mains (AC) Line Instruction (not applicable for Europe, U.S.A., Canada, Australia and U.K.)
Instrucción sobre la línea de la red (CA) (no aplicable para Europa, EE.UU., Canadá, Australia, ni el Reino Unido)
Instrução sobre a tensão da rede eléctrica (CA) (não aplicável para a Europa, os E.U.A., o Canadá, a Austrália e o Reino Unido)
VOLTAGE SELECTOR
110V
220V
127V
230 - 240V
VOLTAGE SELECTOR
220V
230 - 240V
CAUTION for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC) line voltage corresponds with the position of the voltage selector switch provided on the outside of this equipment and, if different, reset the voltage selector switch, to prevent from a damage or risk of fire/electric shock.
PRECAUCIÓN para la línea de la red (CA)
ANTES DE ENCHUFAR EL EQUIPO, compruebe si la tensión de la línea de la red (CA) corresponde con la posición del selector de tensión situado en la parte exterior del equipo, y si es diferente, reajuste el selector de tensión para evitar el riesgo de incendios/ descargas eléctricas.
110V
127V
PRECAUÇÃO para a ligação à tensão da rede (CA)
ANTES DE LIGAR O APARELHO A UMA TOMADA DA REDE, verifique se a tensão da rede CA corresponde à posição do selector de voltagem localizado na parte externa deste equipamento. Caso não corresponda, reajuste o selector de voltagem a fim de evitar avarias ou riscos de incêndio e choque eléctrico.
EN, SP, PR, CH
VICTOR COMPANY OF JAPAN, LIMITED
0600HIMMDWJEIN
JVC
Loading...