JVC MXJE-5 Service manual

SERVICE MANUAL

COMPACT COMPONENT SYSTEM

MB35420053

MX-JE5

Area suffix

US ------------------------ Singapore
UX -------------------- Saudi Arabia
UG --- Turkey,South Africa,Egypt
UN ----------------------------- Asean

(SP-XSJE5)

(SP-XJE5) (SP-XSJE5)

(CA-MXJE5)

(SP-XJE5)

TABLE OF CONTENTS

1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-32

5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-39

COPYRIGHT © 2005 Victor Company of Japan, Limited

No.MB354

2005/3

SPECIFICATION

Amplifier section Output Power 100 W per channel, min. RMS, driven into 6 Ω at 1 kHz

with no more than 10% total harmonic distortion.

Digital output OPTICAL DIGITAL OUTPUT -21 dBm to -15 dBm (660 nm ±30 nm)

Audio input sensitivity/
Impedance*

VIDEO OUT Color system NTSC/PAL selectable

Speaker Terminals 6 Ω - 16 Ω (Main speakers)

Tuner section FM tuning range 87.50 MHz - 108.00 MHz

AM (MW) tuning range 531 kHz - 1 710 kHz (at 9 kHz)

For Saudi Arabia only 531 kHz - 1 602 kHz (at 9 kHz)

Disc player section Playable disc DVD Audio/ DVD Video/CD/VCD/SVCD

Dynamic range 90 dB

Horizontal resolution 500 lines

Wow and flutter Immeasurable

Cassette deck section Frequency response Normal (type I) 50 Hz - 14 000 Hz

Wow and flutter 0.15% (WRMS)

General Power requirement AC 110 V / AC 127 V / AC 220 V / AC 230 V - AC 240

Power consumption 135 W (at operation) 17 W (on standby)

Dimensions (approx.) 265 mm × 335 mm × 352 mm (W/H/D)

Mass (approx.) 8.3 kg

Speakers Type 3-Way 3-Speaker Bass Reflex Type (Magnetically

Speakers Woofer 15 cm cone × 1

Power handling capacity 100 W

Impedance 6 Ω

Frequency range 42 Hz - 29 000 Hz

Sound pressure level 83 dB/W·m

Dimensions (approx.) 205 mm × 335 mm × 250 mm (W/H/D)

Mass (approx.) 3.6 kg each

Surround speakers Type 1-Way Bass Reflex Type

Speaker 8 cm cone × 1

Power handling capacity 40 W

Impedance 16Ω
Dimensions (approx.) 105 mm × 230 mm × 125 mm (W/H/D)

Mass (approx.) 0.7 kg each

AUX 300 mV/47 kΩ
MIC 1/2 3.0 mV/50 kΩ

VIDEO (composite) 1 V(p-p)/75Ω
S-VIDEO Y (luminance):1 V(p-p)/75Ω

C (chrominance, burst):0.286 V(p-p)/75Ω

COMPONENT
(Interlace/Progressive)

Midrange 5 cm cone × 1
Tweeter 2 cm dome × 1

(Y):1 V(p-p)/75Ω
(PB/PR):0.7 V(p-p)/75Ω

530 kHz - 1 710 kHz (at 10 kHz)

530 kHz - 1 600 kHz (at 10 kHz)

CD-R/CD-RW (recorded in Audio CD/ Video CD/
Super Video CD/ MP3/ WMA/ JPEG format)
DVD-R/DVD-RW (recorded in video format)

V , (adjustable with the voltage selector), 50 Hz / 60 Hz

Shielded type)

*Measured at 1 kHz, with tape recording signal 300 mV
Design and specifications are subject to change without notice.

1-2 (No.MB354)

SECTION 1

PRECAUTION

1.1 Safety Precautions

(1) This design of this product contains special hardware and

many circuits and components specially for safety purpos­es. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be per­formed by qualified personnel only.

(2) Alterations of the design or circuitry of the product should

not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.

(3) Many electrical and mechanical parts in the products have

special safety-related characteristics. These characteris­tics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by us­ing replacement components rated for higher voltage, watt­age, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Ser­vice Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety charac­teristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.

(4) The leads in the products are routed and dressed with ties,

clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassem­bling.

(5) Leakage shock hazard testing

After reassembling the product, always perform an isola­tion check on the exposed metal parts of the product (an­tenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.

• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particular­ly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage cur­rent must not exceed 0.5mA AC (r.m.s.).

• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000
in the following manner. Connect a 1,500
paralleled by a 0.15
exposed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC

Ω per volt or more sensitivity

Ω 10W resistor

µF AC-type capacitor between an

voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).

AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)

0.15 F AC TYPE

Place this
probe on

1500 10W

Good earth ground

1.2 Warning

(1) This equipment has been designed and manufactured to

meet international safety standards.

(2) It is the legal responsibility of the repairer to ensure that

these safety standards are maintained.

(3) Repairs must be made in accordance with the relevant

safety standards.

(4) It is essential that safety critical components are replaced

by approved parts.

(5) If mains voltage selector is provided, check setting for local

voltage.

1.3 Caution

Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of pre­forming repair of this system.

1.4 Critical parts for safety

In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)

each exposed
metal part.

(No.MB354)1-3

1.5 Preventing static electricity

Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.

1.5.1 Grounding to prevent damage by static electricity

Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.

(1) Ground the workbench

Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.

(2) Ground yourself

Use an anti-static wrist strap to release any static electricity built up in your body.

(caption)
Anti-static wrist strap

1M

Conductive material
(conductive sheet) or iron palate

(3) Handling the optical pickup

• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)

• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.

1.6 Handling the traverse unit (optical pickup)

(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the

replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a

time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.

1.7 Attention when traverse unit is decomposed

*Please refer to "Disassembly method" in the text for the pickup unit.

• Apply solder to the short land sections before the flexible wire is disconnected from the connecto on the servo board. (If the flexible
wire is disconnected without applying solder, the pickup may be destroyed by static electricity.)

• In the assembly, be sure to remove solder from the short land sections after connecting the flexible wire.

Connector

Short land section

Pickup

1-4 (No.MB354)

Card wire

Traverse mechanism assembly

1.8 Important for laser products

!

1.CLASS 1 LASER PRODUCT

2.DANGER : Invisible laser radiation when open and inter

lock failed or defeated. Avoid direct exposure to beam.

3.CAUTION : There are no serviceable parts inside the

Laser Unit. Do not disassemble the Laser Unit. Replace

the complete Laser Unit if it malfunctions.

4.CAUTION : The CD,MD and DVD player uses invisible

laser radiation and is equipped with safety switches which

prevent emission of radiation when the drawer is open and

the safety interlocks have failed or are defeated. It is

dangerous to defeat the safety switches.

5.CAUTION : If safety switches malfunction, the laser is able

to function.

6.CAUTION : Use of controls, adjustments or performance of

procedures other than those specified here in may result in

hazardous radiation exposure.

Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.

REPRODUCTION AND POSITION OF LABELS

WARNING LABEL

CAUTION : Visible and Invisible

laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM. (e)

CLASS 1
LASER PRODUCT

ADVARSEL : Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejeler.
Undgå direkte eksponering til
stråling. (d)

CAUTION : Visible and Invisible
laser radiation when open and
interlock failed or defeated.
AVOID DIRECT EXPOSURE TO
BEAM. (e)

VARNING : Synlig och
osynling laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen. (s)

VARNING : Synlig och
osynling laserstrålning när
den öppnas och spärren är
urkopplad. Betrakta ej
strålen. (s)

VARO : Avattaessa ja suojalukitus
ohitettuna tai viallisena olet alttiina
näkyvälle ja näkymättömälle
lasersäteilylle. Vältä säteen
kohdistumista suoraan itseesi. (f)

ADVARSEL : Synlig og usynlig
laserstråling når maskinen er
åben eller interlocken fejeler.
Undgå direkte eksponering til
stråling. (d)

VARO : Avattaessa ja suojalukitus
ohitettuna tai viallisena olet alttiina
näkyvälle ja näkymättömälle
lasersäteilylle. Vältä säteen
kohdistumista suoraan itseesi. (f)

(No.MB354)1-5

SECTION 2

SPECIFIC SERVICE INSTRUCTIONS

This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.

1-6 (No.MB354)

SECTION 3

DISASSEMBLY

3.1 Main body section

3.1.1 Removing the metal cover
(See Figs.1 to 3)

(1) From the both sides of the main body, remove the two

screws A attaching the metal cover. (See Figs.1 and 2.)

(2) From the back side of the main body, remove the six

screws B attaching the metal cover. (See Fig.3.)

(3) Remove the metal cover from the main body while lifting

the rear section of the metal cover in the direction of the ar­row. (See Figs.1 and 2.)

Metal cover

Metal cover

A

Fig.1

Metal cover

B

A

Fig.2

B

B

Fig.3

(No.MB354)1-7

3.1.2 Removing the front panel assembly
(See Figs.4 to 7)

• Remove the metal cover.

(1) From the right side of the main body, remove the screw C

attaching the earth wires on the reverse side of the main
board. (See Fig.4.)

Reference:

After attaching the earth wires, fix them with a spacer as
before. (See Fig.4.)

(2) Remove the plastic rivet attaching the main board. (See

Fig.4.)

(3) From the inside of the main body, disconnect the card wires

from the connectors (CN303
ward side of the main board. (See Fig.4.)

(4) Remove the wire clamp fixing the wires and disconnect the

wires from the connector (CN301
side of the main board. (See Fig.5.)

Reference:

After connecting the wires to the connectors, fix the wires
with the wire clamp as before. (See Fig.5.)

(5) From the left side of the main body, disconnect the parallel

wire from the connector CN103
(See Fig.5.)

(6) Disconnect the wire from the connector CN119

transformer board. (See Fig.5.)

Reference:

After connecting the wire, pass the wire through the slot
b of the holder board as before. (See Fig.5.)

(7) Remove the tie band fixing the parallel wire and disconnect

the parallel wire from the connector CN106
terminal board. (See Fig.5.)

Reference:

• After connecting the parallel wire, fix the parallel wire
with a new tie band as before. (See Fig.5.)

• After connecting the wire, pass the wire through the
slot b of the holder board as before. (See Fig.5.)

(8) From the top side of the main body, remove the two screws

D attaching the front panel assembly to the main body.
(See Fig.6.)

(9) From the bottom side of the main body, remove the three

screws E and two screws F attaching the front panel as­sembly. (See Fig.7.)

(10) Release the claws a and remove the front panel assembly

from the main body in the direction of the arrow. (See
Fig.7.)

, CN860, CN880) on the for-

, CN302) on the forward

on the transformer board.

on the

on the speaker

Plastic rivet

CN860

CN303

Speaker terminal board

CN880

Spacer

Earth wires

CN106

Parallel wire

Main board

C

Fig.4

Holder board

b

Wire

Parallel
wire

CN103

1-8 (No.MB354)

Tie band

wires

Transformer board

CN119

CN301

CN302

Main board

Wire clamp

Fig.5

Front panel assembly

D

D

Fig.6

Front panel assembly

Fig.7

a

E

F

a

E

(No.MB354)1-9

3.1.3 Removing the tuner
(See Figs.8 and 9.)

• Remove the metal cover.

(1) From the top side of the main body, disconnect the card

wire from the connector CN21 on the main board. (See
Fig.8.)

(2) From the back side of the main body, remove the two

screws G attaching the tuner to the rear panel. (See Fig.9.)

3.1.4 Removing the video board
(See Figs.8 and 9.)

• Remove the metal cover.

(1) From the top side of the main body, disconnect the card

wire from the connector CN410
Fig.8.)

(2) From the back side of the main body, remove the three

screws H attaching the video board to the rear panel. (See
Fig.9.)

on the main board. (See

Tuner

CN410 CN21 Main board

Video boardCard wires

Fig.8

Tuner

H

Video board

G

Rear panel

Fig.9

1-10 (No.MB354)

3.1.5 Removing the rear panel

(See Figs.10 and 11)

• Remove the metal cover.

(1) From the back side of the main body, remove the screw J

attaching the rear cover. (See Fig.10.)

(2) Release the sections c and remove the rear cover from the

rear panel. (See Fig.10.)

(3) Remove the two screws K and seventeen screws L attach-

ing the rear panel. (See Fig.11.)

Reference:

Remove the tuner and video board as required. (See
Figs.8 and 9.)

(4) From the both sides of the main body, release the sections

d of the center chassis in the direction of the arrow and re­lease the joints e attaching the rear panel to the bottom
chassis. (See Fig. 11.)

J

c

Rear panelRear cover

Fig.10

Rear panel

L

L

e e

L

Bottom chassis

d

L

K

Fig.11

(No.MB354)1-11

3.1.6 Removing the DVD mechanism assembly

r

r

(See Figs.12 and 13)

• Remove the metal cover, tuner and video board.

(1) From the top side of the main body, remove the three

screws M attaching the DVD mechanism assembly on the
center chassis. (See Fig.12.)

(2) From the forward side of the main board, disconnect the

card wires from the connectors (CN11
(See Fig.12.)

Reference:

When reassembly, pass the card wire through the sec­tion f of the main board before connecting the card wire
to the connector CN11

(3) Remove the spacers fixing the card wires. (See Fig.12.)

Reference:

After connecting the card wires, fix them with the spacers
as before. (See Fig.12.)

(4) From the inside of the main body, take out the DVD mech-

anism assembly.

(5) Remove the tray fitting from the DVD mechanism assembly

in the direction of the arrow. (See Fig.13.)

. (See Fig.12.)

, CN511, CN513).

DVD mechanism assembly

M

Main board

Card wire

Center chassis

M

Space

Card
wires

Space

CN513CN11

CN511

f

Card wire

Fig.12

DVD mechanism assembly

Tray fitting

Fig.13

1-12 (No.MB354)

3.1.7 Removing the main board

(See Figs.14 and 15)

• Remove the metal cover, tuner, video board and rear panel.

(1) From the right side of the main body, remove the screw N

attaching the earth wires on the reverse side of the main
board. (See Fig.14.)

Reference:

After attaching the earth wires, fix them with a spacer as
before. (See Fig.14.)

(2) Remove the plastic rivet attaching the main board. (See

Fig.14.)

(3) From the inside of the main body, disconnect the card wires

from the connectors (CN11

, CN880) on the forward side of the main board.

CN860

(See Figs.14 and 15.)

Reference:

When reassembly, pass the card wire through the sec­tion f of the main board before connecting the card wire
to the connector CN11

(4) Remove the wire clamp fixing the wires and disconnect the

wires from the connector (CN301
side of the main board. (See Fig.15.)

Reference:

After connecting the wires to the connectors, fix the wires
with the wire clamp as before. (See Fig.15.)

(5) Disconnect the parallel wire from the connectors (CN220

) on the main board. (See Fig.15.)

CN221

(6) Release the lock g of the connector CN216 on the main

board in the direction of the arrow 1 and disconnect the
main board from the connector CN216
minal board toward this side. (See Fig.14.)

Note:

When releasing the lock g, take care not to break it. (See
Fig.14.)

(7) Release the lock h of the connector CN201

board in the direction of the arrow 2 and disconnect the
connector CN211

CN201 in the direction of the arrow 3. (See Fig.14.)

Note:

When releasing the lock h, take care not to break it. (See
Fig.14.)

on main board from the connector

, CN303, CN511, CN513,

. (See Fig.14.)

, CN302) on the forward

on the speaker ter-

on the primary

Main board

CN880

f

CN860

Plastic
rivet

CN303

Spacer

,

CN513

Card
wires

Earth wires

Main board

CN201

CN511

Card wire

CN11

CN11 CN513

CN211

N

3

h

2

Primary board

Fig.14

CN880

CN216

1

Speaker terminal
board

Main board

f

CN511

CN216

CN206

g

CN860

CN221

Main boardParallel wire

CN220

wires

CN303

CN301

CN302

Main board

Wire clamp

Fig.15

(No.MB354)1-13

3.1.8 Removing the center chassis assembly
(See Fig.16)

• Remove the metal cover, tuner, video board and rear panel.

(1) From the top side of the main body, disconnect the card

wires from the connectors (CN11, CN511, CN513) on the
main body.

Reference:

When reassembly, pass the card wire through the sec­tion f of the main board before connecting the card wire
to the connector CN11

(2) Remove the two screws P attaching the center chassis as-

sembly.

(3) Take out the center chassis assembly with the DVD mech-

anism assembly from the main body.

.

CN513

CN511

CN11

Card wire

Main board

f

3.1.9 Removing the transformer board
(See Fig.17)

• Remove the metal cover, tuner, video board, rear panel and

center chassis assembly.
(1) From the top side of the main body, disconnect the wire

and power cord from the connectors (CN119
the transformer board.

(2) Disconnect the parallel wire from the connector CN103 on

the transformer board.

(3) Remove the four screws Q attaching the transformer board

and take out the transformer board from the main board.

, CN250) on

Card
wires

DVD mechanism assembly

Q

P

Center chassis assembly

Fig.16

1-14 (No.MB354)

Power
cord

CN250

Q

CN119

Transformer board

Fig.17

Q

CN103

Parallel wire

3.1.10 Removing the speaker terminal board

(See Fig.18.)

• Remove the metal cover, tuner, video board, rear panel, main

board and center chassis assembly.
(1) From the top side of the main body, remove the tie band fix-

ing the parallel wire.

Reference:

After connecting the parallel wire, fix it with the new tie
band.

(2) Disconnect the parallel wire from the connector CN106

the speaker terminal board.

(3) Release the locks (i, j) of the connectors (CN205

and disconnect the speaker terminal board in an upward di­rection.

Note:

When releasing the locks (i, j), take care not to break them.

on

, CN214)

Speaker terminal board

CN205

CN214

i

j

Primary board

CN106 Tie band

Speaker terminal board

Fig.18

Parallel wire

(No.MB354)1-15

3.1.11 Removing the regulator board and main & surround amplifier board
(See Figs.19 and 20)

• Remove the metal cover, tuner, video board, rear panel, main

board, center chassis assembly and speaker terminal board.
(1) From the top side of the main body, disconnect the regula-

tor and main & surround amplifier boards in an upward di­rection while releasing the locks (k, m) of the connectors
(CN202

Note:

(2) Take out the regulator and main & surround amplifier

boards at the same time from the main body.

(3) Remove the two screws R attaching the leaf spring to the

heat sink and remove the regulator board from the heat
sink. (See Fig.20.)

(4) Remove the three screws R attaching the main & surround

amplifier board to the heat sink. (See Fig.20.)

, CN203) on the primary board. (See Fig.19.)

When releasing the locks (k, m), take care not to break
them. (See Fig.19.)

Main & surround amplifier board

k

CN202

Primary board

m

Primary board

Regulator board

Regulator board

CN203

Fig.19

Main & surround amplifier board

R

1-16 (No.MB354)

R

Leaf spring

R

Heat sink

Fig.20

3.1.12 Removing the primary board

r

(See Fig.21)

• Remove the metal cover, tuner, video board, rear panel, main

board, center chassis assembly, speaker terminal board, reg­ulator board and main & surround amplifier board.
(1) From the top side of the main body, disconnect the wire

from the connector CN119

Reference:

Pass the wire through the slot n of the holder board be­fore connecting the wire to the connector.

(2) Remove the screw S attaching the primary board on the

bottom chassis.

(3) Remove the section p of the primary board and take out the

primary board from the bottom chassis.

on the transformer board.

Primary board Bottom chassis

p

S

Holde
board

n

Transformer board

Fig.21

CN119

Wire

(No.MB354)1-17

3.1.13 Removing the FL board

V

(See Figs.22 and 23)

• Remove the metal cover and front panel assembly.

(1) From the front side of the front panel assembly, pull the vol-

ume knob out of the front panel assembly. (See Fig.22.)

(2) From the inside of the front panel assembly, remove the six

screws T attaching the FL board. (See Fig.23.)

(3) Release the claws q in the direction of the arrow and take

out the FL board from the front panel assembly. (See
Fig.23.)

3.1.14 Removing the switch board
(See Figs.22 to 24)

• Remove the metal cover and front panel assembly.

(1) From the front side of the front panel assembly, pull the mi-

crophone knob out of the front panel assembly. (See
Fig.22.)

(2) From the inside of the front panel assembly, remove the

three screws U and screw U' attaching the stay bracket.
(See Fig.23.)

Reference:

When attaching the screw U', attach the earth wire with
it. (See Fig.23.)

(3) From the inside of the front panel assembly, remove the

eleven screws V attaching the switch board. (See Fig.24.)

(4) Take out the switch board from the front panel assembly.

3.1.15 Removing the cassette mechanism assembly
(See Fig.24)

• Remove the metal cover and front panel assembly.

(1) From the inside of the front panel assembly, remove the

three screws W, screw W' and two screws X attaching the
cassette mechanism assembly.

(2) Take out the cassette mechanism assembly from the front

panel assembly.

Reference:

• When attaching the screw W', attach the earth wire with it.

• When attaching the screws X, attach the swing cam (L)/(R)
with them.

q

T

U
U'

Earth wire

V

TT

FL board

T

U

Stay bracketFront panel assembly

Fig.23

Switch board

Front panel assembly

Volume knob

Microphone knob

1-18 (No.MB354)

Front panel assembly

Fig.22

X

Earth
wire

Swing cam (R)

Cassette mechanism

W'

assembly

X

W

Swing cam (L)

Fig.24

3.2 DVD mechanism section

• Remove the DVD mechanism assembly from the main body.
(See "3.1.6 Removing the DVD mechanism assembly".)

3.2.1 Removing the clamper base

(See Fig.1)

(1) From the top side of the DVD mechanism assembly, re-

move the two screws A attaching the clamper base.

(2) Lift the clamper base in an upward direction to remove it

from the projections a of the DVD mechanism assembly.

(3) Slide the clamper base in the direction of the arrow and re-

move it from the joints b.

Clamper base

A

a

b

3.2.2 Removing the tray assembly

(See Fig.2)

(1) From the top side of the DVD mechanism assembly, re-

move the two screws B attaching the shaft guide of the tray
assembly.

(2) Remove the tray assembly from the projections c of the

DVD mechanism assembly and take out the tray assem­bly.

a

A

DVD mechanism assembly

Tray assembly

b

Fig.1

DVD mechanism assembly

Shaft guide

cc

B

Fig.2

(No.MB354)1-19

3.2.3 Removing the traverse mechanism assembly
(See Figs.3)

(1) From the bottom side of the DVD mechanism assembly, re-

move the four screws C attaching the traverse mechanism
assembly.

(2) Take out the traverse mechanism assembly with the DVD

module board.

DVD mechanism assembly

DVD module board

3.2.4 Removing the DVD module board
(See Figs.4 and 5)

• Remove the traverse mechanism assembly.

(1) From the side of the traverse mechanism assembly, solder

the short land sections d on the pickup. (See Fig.4.)

(2) From the bottom side of the traverse mechanism assem-

bly, release the lock of the connector CN101
module board in the direction of the arrow 1 and disconnect
the card wire. (See Fig.5.)

Caution:

• Solder the short land sections d on the pickup before
disconnecting the card wire from the connector CN101
on the DVD module board. If the card wire is discon­nected without attaching solder, the pickup may be de­stroyed by static electricity. (See Figs.4 and 5.)

• When attaching the DVD module board, be sure to re­move solders from the short land sections d after con­necting the card wire to the connector CN101
DVD module board. (See Figs.4 and 5.)

(3) Disconnect the card wire from the connector CN201

DVD module board. (See Fig.5.)

(4) Remove the two screws D attaching the DVD module

board. (See Fig.5.)

(5) Remove the DVD module board from the projection e in an

upward direction and remove the engagement section g in
the direction 3 while removing the engagement section f in
the direction of the arrow 2. (See Fig.5.)

on the DVD

on the

on the

C

Traverse mechanism assembly

Fig.3

d

Traverse mechanism assembly

Fig.4

e

D

Card wire

11

2

Card wire

CN101

C

Pickup

CN201

D

g

3

1-20 (No.MB354)

f

DVD module board

Traverse mechanism assembly

Fig.5

3.2.5 Removing the pickup
(See Figs.4,6 to 8)

• Remove the traverse mechanism assembly.

(1) From the side of the traverse mechanism assembly, solder

the short land sections d on the pickup. (See Fig.4.)

(2) Release the lock of the connector on the pickup in the di-

rection of the arrow and disconnect the card wire. (See
Fig.6.)

Caution:

• Solder the short land sections d on the pickup before
disconnecting the card wire from the connector on the
pickup. If the card wire is disconnected without attach­ing solder, the pickup may be destroyed by static elec­tricity. (See Figs.4 and 6.)

• When attaching the pickup, be sure to remove solders
from the short land sections d after connecting the
card wire to the connector on the pickup. (See Figs.4
and 6.)

(3) Remove the screw E attaching the plate and thrust spring.

(See Fig.6.)

(4) Remove the engagement section h attaching the plate to

the feed holder and remove the plate. (See Fig.6.)

(5) Remove the engagement sections (i, j), remove the thrust

spring. (See Fig.6.)

(6) Remove the shaft of the pickup from the section k on the

traverse mechanism assembly and remove the shaft from
the section m while moving it in the direction of the arrow.
(See Fig.7.)

(7) Remove the pickup from the section n of the traverse

mechanism assembly and take out the pickup with the
shaft. (See fig.7.)

(8) From the bottom side of the pickup, remove the two screws

F attaching the SW actuator and lead spring. (See Fig.8.)

(9) Pull the shaft out of the pickup. (See Fig.8.)

i

Thrust spring

Plate

E

j

Thrust spring

h

Card wire

Traverse mechanism assembly

Feed holder

Connector

Fig.6

Traverse mechanism assembly

Pickup

k

Shaft

Pickup

Fig.7

Torsion spring

m

n

(No.MB354)1-21

3.2.6 Attaching the pickup
(See Figs.4,6 to 9)

• See "3.2.5 Removing the pickup".

(1) Attach the shaft, SW actuator and lead spring to the pickup.

(See Fig.8.)

(2) Align the pickup to the section n of the traverse mechanism

assembly first and set the both ends of the shaft of the pick­up in the sections (k, m) of the traverse mechanism assem­bly. (See Fig.7.)

Note:

When attaching the shaft to the section m, attach it under

the torsion spring. (See Fig.7.)
(3) Attach the plate and thrust spring. (See Fig.6.)
(4) Remove solders from the short land sections d after con-

necting the card wire to the connector on the pickup. (See
Figs.4 and 6.)

(5) Turn the feed gear M in the direction of the arrow 1 to move

the pickup in the direction of the arrow 2. (See Fig.9.)

Shaft

Feed gear M

Fig.8

Pickup

SW actuator

Lead spring

F

1

2

Pickup

Fig.9

1-22 (No.MB354)

3.2.7 Removing the feed motor
(See Figs.10 to 12)

• Remove the traverse mechanism assembly.

(1) From the top side of the traverse mechanism assembly, re-

move the screw G attaching the plate and thrust spring.
(See Fig.10.)

(2) Remove the engagement section p attaching the plate to

the feed holder and remove the plate. (See Fig.10.)

(3) Remove the engagement sections (q, r), remove the thrust

spring. (See Fig.10.)

(4) Remove the wires from the soldered section s on the spin-

dle motor board. (See Fig.11.)

Reference:

When attaching the feed motor, pass the wire through
the section t on the spindle base. (See Fig.11.)

(5) Remove the feed holder, feed motor, lead screw, feed gear

E and feed gear M at the same time after removing the
three screws H attaching the feed holder. (See Fig.11.)

(6) From the side of the feed holder, remove the two screws J

attaching the feed motor. (See Fig.12.)

3.2.8 Removing the spindle motor board
(See Figs.11 and 13)

• Remove the traverse mechanism assembly and DVD module

board.
(1) From the top side of the traverse mechanism assembly, re-

move the wires from the soldered section s on the spindle
motor board. (See Fig.11.)

(2) From the bottom side of the traverse mechanism assem-

bly, remove the three screws K attaching the spindle motor
board. (See Fig.13.)

Feed gear M

Feed gear E

H

Feed holder

J

H

Feed motor

Spindle base

Fig.11

Lead screw

Wires

Spindle motor board

Feed holder

t

s

q

Thrust spring

Plate

G

r

Thrust spring

p

Fig.12

Traverse mechanism assembly

Feed holder

Traverse mechanism assembly

K

Fig.13

Fig.10

(No.MB354)1-23

3.2.9 Removing the switch board
(See Fig.14.)

(1) From the bottom side of the DVD mechanism assembly, re-

move the screw L attaching the switch board.

(2) Disconnect the card wire from the connector CN1 on the

switch board.

(3) Remove the wires from the soldered section u on the

switch board.

(4) Lift the switch board while pressing the claw v of the DVD

mechanism assembly in the direction of the arrow and re­move it from the section w.

Reference:

Put the wires on the section x after attaching the switch board
to the DVD mechanism assembly.

3.2.10 Removing the motor
(See Figs.14 and 15)

• Remove the clamper base and tray assembly.

(1) From the bottom side of the DVD mechanism assembly, re-

move the wires from the soldered section u on the switch
board. (See Fig.14.)

(2) From the top side of the DVD mechanism assembly, re-

move the belt from the motor pulley. (See Fig.15.)

Note:

Take care not to attach grease on the belt.

(3) Remove the two screws M attaching the motor to the DVD

mechanism assembly and take out the motor from the bot­tom side of the DVD mechanism assembly. (See Fig.15.)

Reference:

Put the wires on the section x after attaching the motor to the
DVD mechanism assembly. (See Fig.14.)

Card wire

L

M

Switch board

CN1

w

x

u

v

Wires

DVD mechanism assembly

Fig.14

Motor pulley

Belt

DVD mechanism assembly

Fig.15

1-24 (No.MB354)