CD-R/-RW/-ROM (CD/VCD/SVCD/MP3/WMA/MPEG1/MPEG-2/ASF*2/JPEG/DivX*2 format)
DVD-R/-RW (DVD Video/DVD Video Recording (VR)/
MP3/WMA/MPEG-1/MPEG-2/ASF*2/JPEG/DivX*2 format)
+R/+RW (DVD Video format)
V , (adjustable with the voltage selector), 50 Hz / 60 Hz
95 W (CA-MXDK1/ CA-MXDK15)
17 W (CA-MXDK1/ CA-MXDK15)
Ω
× 337 mm × 370 mm (W/H/D)
Ω at 1 kHz
Ω at 63 Hz
1-2 (No.MB515)
Speaker section
(except for MX-DK5)
Main speakers
(SP-MXDK3F/
SP-MXDK1F/
SP-MXDK15F)
Subwoofer
(SP-MXDK3W)
(only for MX-DK3)
Type3-Way 3-Speaker Bass Reflex Type (Magnetically-Shielded Type)
SpeakersWoofer16 cm cone × 1
Midrange5 cm cone × 1
Tweeter2 cm dome × 1
Power handling capacity100 W (SP-MXDK3F)
Impedance6 Ω
Frequency range45 Hz - 20 000 Hz
Sound pressure level85 dB/W·m
Dimensions (approx.)215 mm × 337 mm × 259 mm (W/H/D)
Mass (approx.)3.7 kg each
Type1-Way Bass Reflex Type (Magnetically-Shielded Type)
Speaker16 cm cone × 1
Power handling capacity100 W
Impedance6 Ω
Dimensions (approx.)215 mm × 337 mm × 259 mm (W/H/D)
Mass (approx.)3.5 kg
*1: Measured at 1 kHz, with tape recording signal 400 mV)
*2: CA-MXDK5 only
Design and specifications are subject to change without notice.
80 W (SP-MXDK1F/SP-MXDK15F)
(No.MB515)1-3
SECTION 1
PRECAUTION
1.1Safety Precautions
(1) This design of this product contains special hardware and
many circuits and components specially for safety purposes. For continued protection, no changes should be made
to the original design unless authorized in writing by the
manufacturer. Replacement parts must be identical to
those used in the original circuits. Services should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the product should
not be made. Any design alterations of the product should
not be made. Any design alterations or additions will void
the manufacturers warranty and will further relieve the
manufacture of responsibility for personal injury or property
damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the
protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special
safety characteristics are identified in the Parts List of Service Manual. Electrical components having such features
are identified by shading on the schematics and by ( ) on
the Parts List in the Service Manual. The use of a substitute
replacement which does not have the same safety characteristics as the recommended replacement parts shown in
the Parts List of Service Manual may create shock, fire, or
other hazards.
(4) The leads in the products are routed and dressed with ties,
clamps, tubings, barriers and the like to be separated from
live parts, high temperature parts, moving parts and/or
sharp edges for the prevention of electric shock and fire
hazard. When service is required, the original lead routing
and dress should be observed, and it should be confirmed
that they have been returned to normal, after reassembling.
(5) Leakage shock hazard testing
After reassembling the product, always perform an isolation check on the exposed metal parts of the product (antenna terminals, knobs, metal cabinet, screw heads,
headphone jack, control shafts, etc.) to be sure the product
is safe to operate without danger of electrical shock.Do not
use a line isolation transformer during this check.
• Plug the AC line cord directly into the AC outlet. Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal parts of the cabinet, particularly any exposed metal part having a return path to the
chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
• Alternate check method
Plug the AC line cord directly into the AC outlet. Use an
AC voltmeter having, 1,000Ω per volt or more sensitivity
in the following manner. Connect a 1,500Ω 10W resistor
paralleled by a 0.15µF AC-type capacitor between an ex-
posed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
voltmeter.
Move the resistor connection to each exposed metal
part, particularly any exposed metal part having a return
path to the chassis, and measure the AC voltage across
the resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Voltage measured any must
not exceed 0.75 V AC (r.m.s.). This corresponds to 0.5
mA AC (r.m.s.).
AC VOLTMETER
(Having 1000
ohms/volts,
or more sensitivity)
0.15 F AC TYPE
Place this
probe on
1500 10W
Good earth ground
1.2Warning
(1) This equipment has been designed and manufactured to
meet international safety standards.
(2) It is the legal responsibility of the repairer to ensure that
these safety standards are maintained.
(3) Repairs must be made in accordance with the relevant
safety standards.
(4) It is essential that safety critical components are replaced
by approved parts.
(5) If mains voltage selector is provided, check setting for local
voltage.
1.3Caution
Burrs formed during molding may be left over on some parts
of the chassis.
Therefore, pay attention to such burrs in the case of preforming repair of this system.
1.4Critical parts for safety
In regard with component parts appearing on the silk-screen
printed side (parts side) of the PWB diagrams, the parts that are
printed over with black such as the resistor ( ), diode ( )
and ICP ( ) or identified by the " " mark nearby are critical
for safety. When replacing them, be sure to use the parts of the
same type and rating as specified by the manufacturer.
(This regulation dose not Except the J and C version)
each exposed
metal part.
1-4 (No.MB515)
1.5Preventing static electricity
Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser
diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs.
1.5.1 Grounding to prevent damage by static electricity
Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
Be careful to use proper grounding in the area where repairs are being performed.
(1) Ground the workbench
Ground the workbench by laying conductive material (such as a conductive sheet) or an iron plate over it before placing the
traverse unit (optical pickup) on it.
(2) Ground yourself
Use an anti-static wrist strap to release any static electricity built up in your body.
(caption)
Anti-static wrist strap
1M
Conductive material
(conductive sheet) or iron palate
(3) Handling the optical pickup
• In order to maintain quality during transport and before installation, both sides of the laser diode on the replacement optical
pickup are shorted. After replacement, return the shorted parts to their original condition.
(Refer to the text.)
• Do not use a tester to check the condition of the laser diode in the optical pickup. The tester's internal power source can easily
destroy the laser diode.
1.6Handling the traverse unit (optical pickup)
(1) Do not subject the traverse unit (optical pickup) to strong shocks, as it is a sensitive, complex unit.
(2) Cut off the shorted part of the flexible cable using nippers, etc. after replacing the optical pickup. For specific details, refer to the
replacement procedure in the text. Remove the anti-static pin when replacing the traverse unit. Be careful not to take too long a
time when attaching it to the connector.
(3) Handle the flexible cable carefully as it may break when subjected to strong force.
(4) I t is not possible to adjust the semi-fixed resistor that adjusts the laser power. Do not turn it.
1.7Attention when traverse unit is decomposed
*Please refer to "Disassembly method" in the text for the pickup unit.
• Apply solder to the short land sections before the card wire is disconnected from the connecto on the servo board. (If the card wire
is disconnected without applying solder, the pickup may be destroyed by static electricity.)
• In the assembly, be sure to remove solder from the short land sections after connecting the card wire.
DVD changer mechanism assembly
DVD servo board
Switch board
DVD traverse mechanism assembly
(No.MB515)1-5
1.8Important for laser products
1.CLASS 1 LASER PRODUCT
2.CAUTION :
(For U.S.A.) Visible and/or invisible class II laser radiation
when open. Do not stare into beam.
(Others) Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
3.CAUTION : Visible and/or invisible laser radiation when
open and inter lock failed or defeated. Avoid direct
exposure to beam.
4.CAUTION : This laser product uses visible and/or invisible
laser radiation and is equipped with safety switches which
prevent emission of radiation when the drawer is open and
the safety interlocks have failed or are defeated. It is
dangerous to defeat the safety switches.
5.CAUTION : If safety switches malfunction, the laser is able
to function.
6.CAUTION : Use of controls, adjustments or performance of
procedures other than those specified here in may result in
hazardous radiation exposure.
!
Please use enough caution not to
see the beam directly or touch it
in case of an adjustment or operation
check.
REPRODUCTION AND POSITION OF LABELS and PRINT
WARNING LABEL and PRINT
1-6 (No.MB515)
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
(No.MB515)1-7
SECTION 3
DISASSEMBLY
3.1Main body
3.1.1 Removing the metal cover
(See Fig.1, 2)
(1) Remove the six screws A attaching the metal cover. (See
Fig.1)
(2) Remove the two screws B attaching the metal cover. (See
Fig.2)
L
A
A
K
J
A
A
A
Fig.1
B
Fig.2
1-8 (No.MB515)
3.1.2 Removing the DVD mechanism assembly
(See Fig.3)
(1) Disconnect the card wires from connector CN300
and CN303 of the main board.
(2) Remove the three screws C attaching the DVD mecha-
nism assembly.
, CN301
CN300
CN302
CN301
C
Fig.3
(No.MB515)1-9
3.1.3 Removing the front panel assembly
(See Fig.4 to 7)
(1) Disconnect the connector wires from connector CN103
the transformer board. (See Fig.4)
(2) Disconnect the card wires from connector CN303
and CN307 of the main board. (See Fig.5)
(3) Disconnect the connector wire from connector CN140
the amplifier board. (See Fig.6)
(4) Remove the two screws D attaching the front panel assem-
bly from bottom side of main body. (See Fig.7)
(5) Remove the one screw E attaching the front panel assem-
bly from left side of main body. (See Fig.4)
(6) Remove the one screw F attaching the front panel assem-
bly from right side of main body. (See Fig.5)
(7) Remove the one screw G attaching the earth wire from
switch board to main board. (See Fig.5)
(8) Disengage the hook a and hook b of the both side of the
front panel and then take out the front panel assembly.
(See Fig.4, 5)
3.1.4 Removing the center chassis
(See Fig.1, 5)
(1) Disconnect the connector wire from connector CN330
the main board. (See Fig. 5)
(2) Remove the one screw H attaching the center chassis.
(See Fig. 5)
(3) Remove the two screws J attaching the center chassis.
(See Fig. 1)
, CN306
of
of
of
H
F
CN307
CN306
CN313
b
CN303
CN330
G
Fig.5
CN335
CN309
CN312
CN314
d
CN311
3.1.5 Removing the tuner pack
(See Fig.1, 5)
(1) Disconnect the card wire from connector CN335
main board. (See Fig. 5)
(2) Remove the two screws K attaching the tuner pack. (See
Fig.1)
of the
CN103
E
CN140
Fig.6
ca
Fig.4
1-10 (No.MB515)
D
Fig.7
3.1.6 Removing the rear panel
(See Fig.1, 4, 5, 8 and 9)
(1) Disconnect the parallel wire from connector CN210
sub woofer jack board. (See Fig.8)
(2) Remove the one screw L attaching the rear cover. (See
Fig. 1)
(3) Remove the twelve screws M attaching the rear panel.
(See Fig. 9)
(4) Disengage the hook c and hook d of the rear panel and
then take out the rear panel. (See Fig.4, 5)
of the
CN210
Fig.8
3.1.7 Removing the main board
(See Fig. 5)
(1) Disconnect the card wire from connector CN312
and CN314 of the main board.
(2) Disengage the connector CN309 and CN311 connect to
primary board and main board and then take out the main
board to upward.
MMMM
Fig.9
, CN313
(No.MB515)1-11
3.1.8 Removing the primary board
(See Fig. 10)
(1) Disconnect the connector wire from connector CN119
the transformer board.
(2) Remove the one screw N attaching the primary board.
3.1.9 Removing the heat sink
(See Fig. 11)
(1) Remove the five screws P attaching the heat sink.
of
CN119
N
Fig.10
3.1.10 Removing the regulator board
(See Fig. 12)
(1) Disconnect the connector CN160
and regulator board.
P
Fig.11
connect to primary board
1-12 (No.MB515)
CN160
Fig.12
3.1.11 Removing the cassette mechanism assembly
(See Fig.13)
(1) Remove the six screws Q attaching the cassette mecha-
nism assembly.
3.1.12 Removing the switch board
(See Fig.14)
(1) Take out the volume knob.
(2) Remove the twelve screws R attaching the switch board.
Q
Q
Fig.13
R
3.1.13 Removing the FL board
(See Fig.15)
(1) Remove the four screws S attaching the FL board.
(2) Remove the two screws T attaching the open/close switch
board.
R
Fig.14
SS
T
Fig.15
(No.MB515)1-13
3.2DVD mechanism
3.2.1 Removing the traverse mechanism
(See Fig.1 to 6)
(1) Remove the two screws A attaching the tramecha holder
from top side of DVD mechanism assembly. (See Fig.1)
(2) Remove the two screws B attaching the DVD module
board. (See Fig.2)
(3) Remove the four screws C attaching the CB holder and
take out it. (See Fig.3)
(4) Remove the four screws D attaching the traverse mecha-
nism. (See Fig.4)
(5) Solder the solder part of DVD pick up. (See Fig.5)
(6) Disconnect the card wire from CN101
DVD module board. (See Fig. 6)
Caution:
• Solder the short land section on the DVD pickup before dis-
connecting the card wire from the connector on the DVD
pickup. If the card wire is disconnected without attaching solders, the pickup may be destroyed by static electricity.
• When attaching the DVD pickup, be sure to remove solders
from the short land section after connecting the card wire to
the connector on the DVD pickup.
and CN201 on the
A
Clamper base
B
A
DVD mechanism assembly
Fig.1
DVD mechanism assembly
B
1-14 (No.MB515)
DVD module board
Fig.2
DVD module board
Solder short land section
Fig.5
C
C
CC
Fig.3
DVD mechanism assembly
Traverse mechanism assembly
DVD module board
CN101
CN201
Fig.6
DD
Fig.4
(No.MB515)1-15
3.2.2 Removing the pickup assembly
(See Fig.7 to 11)
(1) Remove the two rod springs pressing the guide shaft. (See
Fig.7)
(2) Remove the screw E and F attaching the spring holder.
(See Fig.8)
(3) Remove the read screw from traverse mechanism assem-
bly. (See Fig.9)
Caution:
When remove the lead screw, do not loss the middle
gear. (See Fig.10 and 11)
(4) Remove the bar spring pressing the shaft. (See Fig.10)
(5) Take out the pickup assembly from traverse mechanism
chassis by order. (See Fig.11)
(SHAFT)
(T.TABLE)
HOOK
(BAR SPRING)
Fig.10
ROD SPRINGROD SPRING
Fig.7
Spring holder
Fig.8
order 2
order 3
order 1
Fig.11
EF
Middle gear
Lead screw
Fig.9
1-16 (No.MB515)
3.2.3 Removing the feed motor assembly
(See Fig.12)
(1) Remove the one screw G attaching the feed motor assem-
bly.
(2) Remove the feed motor wires from solder part of spindle
motor board.
Splder part
3.2.4 Removing the spindle motor assembly
(See Fig.13)
(1) Remove the two screws H attaching the spindle motor from
spindle motor board.
Middle gear
Lead screw
Fig.12
H
Spindle motor
Fig.13
G
(No.MB515)1-17
3.2.5 Removing the tray assembly
(See Fig.14 & 15)
(1) Remove the two screws J attaching the clamper base.
(See Fig.14)
(2) Remove the one screw K attaching the shaft guide from
bottom side. (See Fig.14)
(3) Remove the two screws L attaching the shaft guide from
top side. (See Fig.15)
Caution:
When attach the tray assembly, boss of loading sub assembly
should attach to guide of bottom side at tray assembly. (See
Fig.15)
J
order 1
order 2
clamper base
L
K
Fig.15
[bottom side]
Fig.14
1-18 (No.MB515)
SECTION 4
ADJUSTMENT
4.1ATTENTION IN SERVICE OF DVD SECTION
(1) When pickup, Flash ROM ,DVD module board were changed, initialize EEPROM by all means.
(2) When full initialization was excuted, excute learning with a DVD test disc by all means.
Test disc : VT-501, VT-502
Learning method : It is adjusted automatically by normal playback of a DVD disc.
4.2TEST MODE
In DVD test mode, initialization processing, the version of a microcomputer, a front end check, JITTA, and a laser current value
are indicated.
StepOperationFunctionRemarks
1The AC code is pulled
out, The STOP and
PLAY key of a main unit
are pushed simultaneously.
The AC code is inserted
2Version display
with the state of 1.
Push the PAUSE key of a
1
main unit.
NORMAL initialization
Push the STOP+POWER+
2
10 key of a remote control
for a long time.
FULL initialization
Push the STOP+POWER+
3
9 key of remote control.
It is made POWER ON in test
mode, and VERSION is displayed
on FL.
* segment of FL is RDS on at the
time of the completion of
initialization.
* segment of FL is COLT START
on at the time of the completion
of initialization.
Display the version of a micom
on FL.
FL display
12345678
TEST J C #
TJC#
TJC#
aa .cc
bbb
__ _
DVD
_
ee ee
.
dd5sec
**
**
**
temporary
5sec
temporary
The version code is as the
following.
0x01: JC 0x02: 1U 0x03: D
0x04: E 0x05: 2U 0x06: 3U
0x07: UB 0x08: UT 0x09: 4U
0x0a: UY 0x0b: EE 0x0c: UF
Region code display
0x00: 0(Free) 0x01: 1 0x02: 2
0x04: 3 0x08: 4 0x10: 5 0x20: 6
0x40: 7 0x80: 8
"X" is indicated at the time as the
one except for the above.
The study state and an
initialization state from a back
end are displayed on the 10th
and 11th figure of FL display.
0xFF : Blank display
The study state(The 10th figure)
0x03: DVD Study un-completing,
CD Study un-completing. ("3")
0x02: DVD Study completing,
CD Study un-completing. ("2")
0x01: DVD Study un-completing,
CD Study completing. ("1")
0x00: DVD Study completing,
CD Study completing. ("0")
The initialization state
(The 11th figure)
0x03: FULL initialization end
("3")
0x00: NORMAL initialization end
("0")
0xFF: Initialization un-ending.
("Blank")
* All printed circuit boards and its assemblies are not available as service parts.
- Contents -
Exploded view of general assembly and parts list (Block No.M1)
DVD mechanism assembly and parts list (Block No.MJ)
DVD loading base assembly and parts list (Block No.MN)
Cassette mechanism assembly and parts list (Block No.MP)
Electrical parts list (Block No.01~06)
Packing materials and accessories parts list (Block No.M3)
(MX-DK1US,MX-DK1UW,MX-DK1UG,MX-DK1UN,MX-DK15UN)
Packing materials and accessories parts list (Block No.M4)
(MX-DK3US,MX-DK3UW,MX-DK3UG,MX-DK3UN)
77QMF51W2-3R15-J8FUSEF104 3.15A AC250V
78GV30349-048ASPACER
79GV30873-002ABUTTON ADK3US,DK3UW,DK3UG,DK3UN
80GV30874-002ABUTTON BDK3US,DK3UW,DK3UG,DK3UN
81GV10321-002ACASS.HOLDER(L)DK3US,DK3UW,DK3UG,DK3UN
82GV10322-002ACASS.HOLDER(R)DK3US,DK3UW,DK3UG,DK3UN
83QYSBSF3035ZATAP SCREWM3 x 35mm(x2)DK3US,DK3UW,DK3UG,DK3UN
84GV10328-003AFRONT PANEL ASSYDK3US,DK3UW,DK3UG,DK3UN
85QYSBSGY3008EATAP SCREWM3 x 8mm(x2)DK3US,DK3UW,DK3UG,DK3UN
86QYSBSGY3008EATAP SCREWM3 x 8mmDK3US,DK3UW,DK3UG,DK3UN
87QAR0405-001FANDK3US,DK3UW,DK3UG,DK3UN
3-5
DVD mechanism assembly and parts list
Block No.
M
J
M
M
Grease
=JVG-31N
=JVS-1003
=1401C
< Back side >
29
28
25
31
24
FXL-D10-1M
31
30
26
27
31
20
23
30
31
22
18
15
21
16
17
14
10
7.0mm
2
+
0.2mm
-
7
6
9
3
3
1
11
12
13
8
5
4
The parts without symbol number are not service.
3-6
DVD mechanism
Symbol No.Part No.Part NameDescriptionLocal
1LV22234-001ATM.CHASSIS
2LV22235-001ASPINDLE BASE
3QYSDST2005ZATAP SCREWM2 x 5mm(x2)
4LV36555-001AG.S.HOLDER
5QYSDST2005ZATAP SCREWM2 x 5mm
6LV44041-002AGUIDE SHAFT
7LV44479-001ABAR SPRING
8LV22236-001AFEED HOLDER
9QAR0165-001FEED MOTOR
10LV30225-0X5ASPACER
11LV36557-001AF.M.GEAR
12QYSPSPT2030MASCREWM2 x 3mm
13QYSDST2005ZATAP SCREWM2 x 5mm
14QAL0786-002P.UP
15LV22237-001ARACK ARM
16LV36560-001ARACK ARM SPRING
17QYSPSFU1740ZATAP SCREWM1.7 x 4mm(x2)
18QUQK05-2415AC-EFFC WIRE24pin 15cm
20LV44041-002AGUIDE SHAFT
21LV36559-001AL.S.GEAR
22LV41517-003ALEAD SCREW
23LV36558-001AMIDDLE GEAR
24LV36556-001ASPRING HOLDER
25LV44623-001ACOMP.SPRING
26QYSDST2005ZATAP SCREWM2 x 5mm
27QYSDST2616MATAP SCREWM2.6 x 16mm
28QAR0386-001S.MOTOR
29QYSPSPU1775ZASCREWM1.7 x 7.5mm(x3)
30LV44042-001AROD SPRING(x2)
31LV44046-001AADJUST SCREW(x4)
Block No. [M][J][M][M]
3-7
DVD loading base assembly and parts list
Grease
JVS-1003
JVG-450
20
19
18
16
h
FMU-MB4-11M
28
14
Block No.
N
M
M
M
2
3
13
15
h
< Back side >
26
25
16
17
j
1
10
11
9
0.10mm
4
7
8
6
7.75mm
Backside
27
5
j
A
B
27
DVD module board
26
26
26
c
12
DVD loading switch board
g
e
f
A
21
23
c
23
22
d
3-8
d
22
23
k
B
22
f
e
24
The parts without symbol number are not service.
DVD loading base
Symbol No.Part No.Part NameDescriptionLocal
1LV11065-004ALOADER SUB ASSY
2E407140-001SSC.D ROLLER
3E407149-001SSRUBBER TUBE
4LV10979-002ATRAY
5LV35499-001ASHAFT GUIDE
6LV44022-001ASHAFT
7QYSSSF2008ZATAP SCREWM2 x 8mm
8QYSDSF2008ZATAP SCREWM2 x 8mm(x2)
9QAR0197-001MOTOR
9orQAR0280-001LOADING MOTOR
10LV43844-002AMOTOR PULLEY
11QYSPSPU1730ZASCREWM1.7 x 3mm(x2)
12QYSDSF2008ZATAP SCREWM2 x 8mm
13LV43974-001ABELT
14LV21852-003ACLAMPER BASE
15QYSDSF2008ZATAP SCREWM2 x 8mm(x2)
16LV41741-004ASPECIAL SCREW
17LV35056-002ADVD CLAMPER
18LV42930-003AP.C.MAGNET
18orLV41118-003AMAGNET
19LV43848-001AYOKE
20LE40906-002ASPECIAL SCREW
21------------SINGLE DVD TRAM
22LV44043-001AINSULATOR(x4)
23LV44044-001ASPECIAL SCREW(x4)
25LV11212-001ACB HOLDER
26QYSBSF2608ZATAP SCREWM2.6 x 8mm(x4)
27LV44209-001AWASHER SCREW(x2)
28LV44603-001ALASER CATION
Block No. [M][N][M][M]
3-9
Cassette mechanism assembly and parts list
QAL0789-001
3
Block No.
9
M
M
P
M
5
7
4
6
6
2
5
7
8
3-10
1
The parts without symbol number are not service.
Cassette mechanism
Symbol No.Part No.Part NameDescriptionLocal
1F513C936PLATE HD BLK
2F525C363MTR MAIN BLK
3F567C719PCB CONTROL BLK
4F522C063CLUTCH ASSY BLK(x2)
5FF19N-31TMAIN BELT(x2)
6F514C135ROLLER PINCH BLK R(x2)
7FF19S-31TF/R BELT MO(x2)
8F513C937PLATE HE BLK
9QAL0789-001CASSETTE MECHA
C1085QTE1V06-106ZE CAPACITOR10uF 35V
C1090QETN1CM-107ZE CAPACITOR100uF 16V M
C1091QFZ0212-104ZM CAPACITOR0.1uF
C1092QFZ0212-104ZM CAPACITOR0.1uF
C1120QCSB1HK-4R7YC CAPACITOR4.7pF 50V K
C1122QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C1123QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C1124QCBB1HK-221YC CAPACITOR220pF 50V K
C1140QCSB1HK-4R7YC CAPACITOR4.7pF 50V K
C1142QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C1143QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C1144QCBB1HK-221YC CAPACITOR220pF 50V K
C1160QETN1JM-476ZE CAPACITOR47uF 63V M
C1161QETN1JM-476ZE CAPACITOR47uF 63V M
C1162QETN1JM-476ZE CAPACITOR47uF 63V M
C1180QCSB1HK-4R7YC CAPACITOR4.7pF 50V K
C1182QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C1183QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C1184QCBB1HK-221YC CAPACITOR220pF 50V K
C1190QETN1HM-105ZE CAPACITOR1uF 50V M
C1221QETM1EM-688E CAPACITOR6800uF 25V M
C1222QETM1CM-688E CAPACITOR6800uF 16V M
C1225QCBB1HK-103YC CAPACITOR0.01uF 50V K
C1226QCBB1HK-221YC CAPACITOR220pF 50V K
C1260QETN1HM-106ZE CAPACITOR10uF 50V M
C1261QETN1CM-227ZE CAPACITOR220uF 16V M
C1270QETN1HM-106ZE CAPACITOR10uF 50V M
C1271QETN1HM-106ZE CAPACITOR10uF 50V M
C1280QETN1HM-106ZE CAPACITOR10uF 50V M
C1281QETN1HM-106ZE CAPACITOR10uF 50V M
C1290QETN1HM-106ZE CAPACITOR10uF 50V M
C1291QETN1HM-106ZE CAPACITOR10uF 50V M
C1295QETN1HM-106ZE CAPACITOR10uF 50V M
C1296QETN1HM-106ZE CAPACITOR10uF 50V M
C2010QETN1JM-107ZE CAPACITOR100uF 63V M
C2011QETN2AM-476ZE CAPACITOR47uF 100V M
C2012QETN1HM-226ZE CAPACITOR22uF 50V M
C2013QETN1HM-226ZE CAPACITOR22uF 50V M
C2014QCBB1HK-103YC CAPACITOR0.01uF 50V K
C2015QETN1HM-106ZE CAPACITOR10uF 50V M
C2019QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C3000NCB31HK-103XC CAPACITOR0.01uF 50V K
C3050NCB31HK-103XC CAPACITOR0.01uF 50V K
C3051NCB31CK-104XC CAPACITOR0.1uF 16V K
C3052QETN1CM-107ZE CAPACITOR100uF 16V M
C3053NCB31HK-103XC CAPACITOR0.01uF 50V K
C3100QETN1CM-107ZE CAPACITOR100uF 16V M
C3101NCB31HK-103XC CAPACITOR0.01uF 50V K
C3102NCB31HK-103XC CAPACITOR0.01uF 50V K
C3103QETN1HM-475ZE CAPACITOR4.7uF 50V M
C3250QETN1HM-106ZE CAPACITOR10uF 50V M
C3251QETN1EM-477ZE CAPACITOR470uF 25V M
C3300QETN1EM-476ZE CAPACITOR47uF 25V M
C3500NDC31HJ-270XC CAPACITOR27pF 50V J
C3501NDC31HJ-270XC CAPACITOR27pF 50V J
C3502QETN1HM-474ZE CAPACITOR0.47uF 50V M
C3503QETN1CM-107ZE CAPACITOR100uF 16V M
C4000QETN1HM-475ZE CAPACITOR4.7uF 50V M
C4001QFLC1HJ-103ZM CAPACITOR0.01uF 50V J
C4002QFVF1HJ-274ZMF CAPACITOR0.27uF 50V J
C4004QTE1V06-106ZE CAPACITOR10uF 35V
C4005QFLC1HJ-153ZM CAPACITOR0.015uF 50V J
C4006QETN1HM-106ZE CAPACITOR10uF 50V M
C4050QTE1V28-107ZE CAPACITOR100uF 35V
C4050QETN1EM-337ZE CAPACITOR330uF 25V MDK1UG
C4050QETN1EM-107ZE CAPACITOR100uF 25V M
C4080QETN1HM-106ZE CAPACITOR10uF 50V M
C4081NCB31EK-683XC CAPACITOR0.068uF 25V K
C4082QETN1HM-226ZE CAPACITOR22uF 50V M
C4100QETN1HM-226ZE CAPACITOR22uF 50V M
C4101QETN1HM-106ZE CAPACITOR10uF 50V M
C4200QETN1HM-226ZE CAPACITOR22uF 50V M
C4201QETN1HM-106ZE CAPACITOR10uF 50V M
C4701QETN1HM-225ZE CAPACITOR2.2uF 50V M
C4702QETN1HM-106ZE CAPACITOR10uF 50V M
C4703QETN1HM-106ZE CAPACITOR10uF 50V M
C4705QETN1JM-476ZE CAPACITOR47uF 63V M
C4707QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C4708QFG32AJ-332ZM CAPACITOR3300pF 100V J
C4708QFLC1HJ-103ZM CAPACITOR0.01uF 50V J
C4709QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C4710QTE1V06-106ZE CAPACITOR10uF 35V
C4710QTE1H06-475ZE CAPACITOR4.7uF 50V
C4711QETN1HM-105ZE CAPACITOR1uF 50V M
C4722QETN1CM-107ZE CAPACITOR100uF 16V M
C4723QETN1JM-476ZE CAPACITOR47uF 63V M
C4730QETN1HM-105ZE CAPACITOR1uF 50V M
C4734QETN1JM-476ZE CAPACITOR47uF 63V M
C4734QTE1H28-106ZE CAPACITOR10uF 50V
C4735NDC31HJ-331XC CAPACITOR330pF 50V J
C4736QETN1JM-476ZE CAPACITOR47uF 63V M
C4801QETN1HM-225ZE CAPACITOR2.2uF 50V M
C4802QETN1HM-106ZE CAPACITOR10uF 50V M
C4803QETN1HM-106ZE CAPACITOR10uF 50V M
C4805QETN1JM-476ZE CAPACITOR47uF 63V M
C4807QFLC1HJ-473ZM CAPACITOR0.047uF 50V J
C4835NDC31HJ-331XC CAPACITOR330pF 50V J
C4836QETN1JM-476ZE CAPACITOR47uF 63V M
C5200QTE1V06-106ZE CAPACITOR10uF 35V
C5300QETN1HM-475ZE CAPACITOR4.7uF 50V M
C5301QETN1HM-105ZE CAPACITOR1uF 50V M
C5601QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C5602QETN1JM-476ZE CAPACITOR47uF 63V M
C5701QFLC1HJ-104ZM CAPACITOR0.1uF 50V J
C5702QETN1JM-476ZE CAPACITOR47uF 63V M
C5801QFVF1HJ-124ZMF CAPACITOR0.12uF 50V J
C5802QFLC1HJ-153ZM CAPACITOR0.015uF 50V J
C6000QETN1HM-106ZE CAPACITOR10uF 50V M
C6850NCB31HK-222XC CAPACITOR2200pF 50V K
C7000QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7001NCB31HK-103XC CAPACITOR0.01uF 50V K
C7002NCB31HK-103XC CAPACITOR0.01uF 50V K
C7003QETN1EM-476ZE CAPACITOR47uF 25V M
C7005QETN1HM-226ZE CAPACITOR22uF 50V M
C7009NCB31HK-103XC CAPACITOR0.01uF 50V K
C7500QETN0JM-477ZE CAPACITOR470uF 6.3V M
C7501NCB31HK-103XC CAPACITOR0.01uF 50V K
C7502QETN0JM-477ZE CAPACITOR470uF 6.3V M
C9001NCB31HK-102XC CAPACITOR1000pF 50V K
C9002QEKC1EM-106ZE CAPACITOR10uF 25V M
C9005NCB31HK-471XC CAPACITOR470pF 50V K
C9091QETN1HM-475ZE CAPACITOR4.7uF 50V M
C9093NCB31HK-103XC CAPACITOR0.01uF 50V K
C9094QETN1HM-475ZE CAPACITOR4.7uF 50V M
C9096QETN1HM-475ZE CAPACITOR4.7uF 50V M
C9097QETN1HM-475ZE CAPACITOR4.7uF 50V M
C9200NCB31HK-103XC CAPACITOR0.01uF 50V K
C9401NCB31HK-103XC CAPACITOR0.01uF 50V K
C9402NCB31HK-103XC CAPACITOR0.01uF 50V K
C9500QEKC1CM-107ZE CAPACITOR100uF 16V M
C9501QEKC1CM-476ZE CAPACITOR47uF 16V M
C9502NCB31CK-104XC CAPACITOR0.1uF 16V K
C9503NCB31CK-104XC CAPACITOR0.1uF 16V K
C9504NCB31CK-823XC CAPACITOR0.082uF 16V K
C9505NCB31CK-823XC CAPACITOR0.082uF 16V K
C9506NCB31HK-103XC CAPACITOR0.01uF 50V K
C9507NCB31HK-561XC CAPACITOR560pF 50V K
C9508NCB31HK-332XC CAPACITOR3300pF 50V K
C9509QEKC1CM-106ZE CAPACITOR10uF 16V M
Part No.Part NameDescriptionLocal
DK3US,
DK3UW,
DK3UG,
DK3UN
DK3US,
DK3UW,
DK3UG,
DK3UN
3-19
Symbol No.
Part No.Part NameDescriptionLocal
Symbol No.
Part No.Part NameDescriptionLocal
C9510QEKC1CM-106ZE CAPACITOR10uF 16V M
C9511QEKC1HM-475ZE CAPACITOR4.7uF 50V M
C9512NCB31HK-561XC CAPACITOR560pF 50V K
C9513NCB31HK-392XC CAPACITOR3900pF 50V K
C9600QEKC1AM-107ZE CAPACITOR100uF 10V M
C9601QEKC1HM-224ZE CAPACITOR0.22uF 50V M
C9602QEKC1HM-104ZE CAPACITOR0.1uF 50V M
C9603NCB31HK-104XC CAPACITOR0.1uF 50V K
C9604NCB31HK-681XC CAPACITOR680pF 50V K
C9605NDC31HJ-151XC CAPACITOR150pF 50V J
C9606QEKC1CM-336ZE CAPACITOR33uF 16V M
C9607QEKC1HM-335ZE CAPACITOR3.3uF 50V M
C9608QEKC1AM-107ZE CAPACITOR100uF 10V M
C9631NCB31HK-102XC CAPACITOR1000pF 50V K
C9632NCB31HK-102XC CAPACITOR1000pF 50V K
C9633NCB21HK-473XC CAPACITOR0.047uF 50V K
C9634QEKC1HM-104ZE CAPACITOR0.1uF 50V M
C9635NCB31HK-391XC CAPACITOR390pF 50V K
C9636NCB31HK-391XC CAPACITOR390pF 50V K
C9637NCB31HK-471XC CAPACITOR470pF 50V K
C9651NCB31HK-102XC CAPACITOR1000pF 50V K
C9899NCB31HK-222XC CAPACITOR2200pF 50V K
C110QETN1HM-106ZE CAPACITOR10uF 50V M
C122QETN1CM-107ZE CAPACITOR100uF 16V M
C202NCB31HK-122XC CAPACITOR1200pF 50V K
C203NCB31HK-103XC CAPACITOR0.01uF 50V K
C204NCB31CK-104XC CAPACITOR0.1uF 16V K
C205QQR1730-001POWER INDUCTOR
C206NCB31CK-104XC CAPACITOR0.1uF 16V K
C209QETN1AM-227ZE CAPACITOR220uF 10V M
C210QETN1HM-105ZE CAPACITOR1uF 50V M
C211QETN1HM-106ZE CAPACITOR10uF 50V M
C212NCB31CK-104XC CAPACITOR0.1uF 16V K
C213QQR1730-001POWER INDUCTOR
C214NCB31CK-104XC CAPACITOR0.1uF 16V K
C216NCB31HK-272XC CAPACITOR2700pF 50V K
C219NCB31HK-103XC CAPACITOR0.01uF 50V K
C220QETN1HM-226ZE CAPACITOR22uF 50V M
C221QETN1HM-105ZE CAPACITOR1uF 50V M
C222QETN1HM-226ZE CAPACITOR22uF 50V M
C223NCB31HK-682XC CAPACITOR
C224NCB31HK-682XC CAPACITOR
C225NCB31HK-122XC CAPACITOR1200pF 50V K
C226QETN1EM-475ZE CAPACITOR4.7uF 25V M
C227QETN1EM-475ZE CAPACITOR4.7uF 25V M
C228QETN1CM-107ZE CAPACITOR100uF 16V M
C231NCB31HK-272XC CAPACITOR2700pF 50V K
C232NCB31HK-152XC CAPACITOR1500pF 50V K
C233NCB31HK-152XC CAPACITOR1500pF 50V K
C300QCBB1HK-331YC CAPACITOR330pF 50V K
C301QCBB1HK-331YC CAPACITOR330pF 50V K
C303QFG32AJ-273ZPP CAPACITOR0.027uF 100V J
C304QETN1CM-107ZE CAPACITOR100uF 16V M
C306QCBB1HK-223YC CAPACITOR0.022uF 50V K
C307QDXB1CM-152YC CAPACITOR1500pF 16V M
C101NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C102NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C103NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C104NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C105NEAF0JM-476XE CAPACITOR47uF 6.3V M
C106NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C107NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C108NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C201NDC31HJ-221XC CAPACITOR220pF 50V J
C202NDC31HJ-221XC CAPACITOR220pF 50V J
C203NCB31HK-103XC CAPACITOR0.01uF 50V K
C204NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C205NCB31HK-271XC CAPACITOR270pF 50V K
C206NDC31HJ-151XC CAPACITOR150pF 50V J
C210NCF31AZ-105XC CAPACITOR1uF 10V Z
C211NCB31HK-223XC CAPACITOR0.022uF 50V K
C217NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C251NCB31AK-474XC CAPACITOR0.47uF 10V K
C256NCB31CK-104XC CAPACITOR0.1uF 16V K
C257NCB31HK-822XC CAPACITOR8200pF 50V K
C258NCB31CK-153XC CAPACITOR0.015uF 16V K
C259NCB31CK-153XC CAPACITOR0.015uF 16V K
C260NCB31HK-223XC CAPACITOR0.022uF 50V K
C261NCB31HK-223XC CAPACITOR0.022uF 50V K
C262NCB31HK-223XC CAPACITOR0.022uF 50V K
C263NEAF1CM-107XE CAPACITOR100uF 16V M
C300NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C301NEAF0JM-227XE CAPACITOR220uF 6.3V M
C302NEAF0GM-476XE CAPACITOR47uF 4V M
C303NBE20JM-476XTA E CAPACITOR47uF 6.3V M
C304NCB30JK-105XC CAPACITOR1uF 6.3V K
C305NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C306NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C307NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C308NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C309NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C310NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C312NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C313NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C314NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C315NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C316NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C318NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C319NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C320NCB31CK-104XC CAPACITOR0.1uF 16V K
C321NCB31CK-104XC CAPACITOR0.1uF 16V K
C322NCB31CK-104XC CAPACITOR0.1uF 16V K
C323NCB31CK-104XC CAPACITOR0.1uF 16V K
C324NCB30JK-105XC CAPACITOR1uF 6.3V K
C325NDC31HJ-120XC CAPACITOR12pF 50V J
C326NDC31HJ-100XC CAPACITOR10pF 50V J
C328NCB31HK-103XC CAPACITOR0.01uF 50V K
C329NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C330NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C331NCB31CK-333XC CAPACITOR0.033uF 16V K
C332NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C333NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C334NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C335NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C337NCB31CK-183XC CAPACITOR0.018uF 16V K
C338NCB31HK-562XC CAPACITOR5600pF 50V K
C339NBE20JM-106XTA E CAPACITOR10uF 6.3V M
C340NCB30JK-105XC CAPACITOR1uF 6.3V K
C341NCB30JK-105XC CAPACITOR1uF 6.3V K
C347NCB31CK-104XC CAPACITOR0.1uF 16V K
C348NCB31CK-104XC CAPACITOR0.1uF 16V K
C349NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C350NCB31HK-103XC CAPACITOR0.01uF 50V K
C351NCB31HK-103XC CAPACITOR0.01uF 50V K
C352NCB31CK-153XC CAPACITOR0.015uF 16V K
C353NCB31HK-561XC CAPACITOR560pF 50V K
C354NCB31HK-561XC CAPACITOR560pF 50V K
C356NCB30JK-105XC CAPACITOR1uF 6.3V K
C359NCB30JK-105XC CAPACITOR1uF 6.3V K
C371NCF31AZ-105XC CAPACITOR1uF 10V Z
C372NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C375NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C376NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C377NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C379NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C380NCB21CK-105XC CAPACITOR1uF 16V K
C381NCB21AK-225XC CAPACITOR2.2uF 10V K
C382NCB31HK-471XC CAPACITOR470pF 50V K
C383NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C386NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C393NCB31HK-103XC CAPACITOR0.01uF 50V K
C455NCB31HK-103XC CAPACITOR0.01uF 50V K
C551NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C554NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C555NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C557NCB31HK-102XC CAPACITOR1000pF 50V K
C558NBE20JM-226XTA E CAPACITOR22uF 6.3V M
C559NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C560NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C562NCF31AZ-105XC CAPACITOR1uF 10V Z
C563NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C564NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C701NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C704NEAF0JM-476XE CAPACITOR47uF 6.3V M
C706NEAF1CM-106XE CAPACITOR10uF 16V M
C707NCF31EZ-104XC CAPACITOR0.1uF 25V Z
C711NCB21CK-105XC CAPACITOR1uF 16V K
C712NCB31HK-103XC CAPACITOR0.01uF 50V K
C713NCB21CK-105XC CAPACITOR1uF 16V K
C740NCB31CK-104XC CAPACITOR0.1uF 16V K
Packing and Accessories
(MX-DK1US,MX-DK1UW,MX-DK1UG,MX-DK1UN,MX-DK15UN)
Block No. [M][3][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1GVT0177-001AINST BOOKENG
A 2GVT0177-003AINST BOOKCHI(PEKIN)DK1US,DK1UN,DK15UN
A 2GVT0177-005AINST BOOKSPA PORDK1UW
A 2GVT0177-004AINST BOOKARA PERDK1UG
A 3GVT0186-001ANOTICE SHEET
A 4GVT0187-001ANOTICE SHEET
A 5QAL0014-003AM LOOP ANT
A 6QAL0457-001ANT.WIRE
A 7QAM0112-002PLUG ADAPTORDK1US,DK1UW,DK1UN,DK15UN
A 8QAM0216-001SIGNAL CORD
A 9RM-SMXDK1UREMOCON
A 10-----------------BATTERY1.5V(x2)
A 12GVT0185-001ANOTICE SHEETDK1UN,DK15UN
A 13MXDK1U-SPBOX-RSPEAKER BOXDK1US,DK1UW,DK1UG,DK1UN
A 13MXDK15U-SPBOX-RSPEAKER BOXDK15UN
A 14MXDK1U-SPBOX-LSPEAKER BOXDK1US,DK1UW,DK1UG,DK1UN
A 14MXDK15U-SPBOX-LSPEAKER BOXDK15UN
A 15441-802104-00LEG CUSHION(x8)
P 1GV20424-001ACARTON ASSY.DK1US,DK1UN
P 1GV20424-003ACARTON ASSY.DK1UW
P 1GV20424-002ACARTON ASSY.DK1UG
P 1GV20452-001ACARTON ASSY.DK15UN
P 2GV10326-001ACUSHION (TOP)
P 3GV10327-001ACUSHION (BOTTOM
P 4QPC06507030PPOLY BAG65cm x 70cm
P 5GV40437-003ACLOTH
P 6QPC02503515PPOLY BAG25cm x 35cm
P 7715-250035-00MIRAMAT SHEET(x2)
P 8700-120034-20HDPE BAG(x2)
P 9720-MXDK1T-00TOP CUSHION
P 10720-MXDK1B-00BOTTOM CUSHION
3-25
Packing materials and accessories parts list
(MX-DK3US,MX-DK3UW,MX-DK3UG,MX-DK3UN)
P9
P11
Block No.
P13
M
4
M
M
A14
P3
P2
P5
P4
A14
A4
A12
P8
P10
A13
A17
A17
P12
P6
A5,A6, A7,
A8,A9, A10
P7
A1,A2, A3
P15
P14
A15
P16
P1
3-26
A16
P14
Packing and Accessories
(MX-DK3US,MX-DK3UW,MX-DK3UG,MX-DK3UN)
Block No. [M][4][M][M]
Symbol No.Part No.Part NameDescriptionLocal
A 1GVT0177-001BINST BOOKENG
A 2GVT0177-003BINST BOOKCHI(PEKIN)DK3US,DK3UN
A 2GVT0177-005AINST BOOKSPA PORDK3UW
A 2GVT0177-004BINST BOOKARA PERDK3UG
A 3GVT0186-001ANOTICE SHEET
A 4GVT0187-001ANOTICE SHEET
A 5QAL0014-003AM LOOP ANT
A 6QAL0457-001ANT.WIRE
A 7QAM0112-002PLUG ADAPTORDK3US,DK3UW,DK3UN
A 8QAM0216-001SIGNAL CORD
A 9RM-SMXDK3UREMOCON
A 10-----------------BATTERY1.5V(x2)
A 12GVT0185-001ANOTICE SHEETDK3UN
A 13GV30906-001ASPEAKER BOX
A 14441-802104-00LEG CUSHION(x4)
A 15MXDK1U-SPBOX-RSPEAKER BOX
A 16MXDK1U-SPBOX-LSPEAKER BOX
A 17441-802104-00LEG CUSHION(x8)
P 1GV20425-001ACARTON ASSY.DK3US,DK3UN
P 1GV20425-003ACARTON ASSY.DK3UW
P 1GV20425-002ACARTON ASSY.DK3UG
P 2GV10337-001ACUSHION (TOP)
P 3GV10338-001ACUSHION (BOTTOM
P 4QPC06507030PPOLY BAG65cm x 70cm
P 5GV40437-003ACLOTH
P 6QPC02503515PPOLY BAG25cm x 35cm
P 7QPC02503515PPOLY BAG25cm x 35cm
P 8GV30909-001ACARTON SPACER
P 9715-250035-00MIRAMAT SHEET
P 10700-120034-20HDPE BAG
P 11720-MXDK3WT-00TOP CUSHION
P 12720-MXDK3WB-00BOTTOM CUSHION
P 13715-250035-00MIRAMAT SHEET(x2)
P 14700-120034-20HDPE BAG(x2)
P 15720-MXDK1T-00TOP CUSHION
P 16720-MXDK1B-00BOTTOM CUSHION
3-27
SCHEMATIC DIAGRAMS
COMPACT COMPONENT SYSTEM
MX-DK1US,MX-DK1UW,MX-DK1UG
MX-DK1UN,MX-DK3US,MX-DK3UW
MX-DK3UG,MX-DK3UN,MX-DK15UN
CD-ROM No.SML200606
CA-MXDK1SP-MXDK1FSP-MXDK1F
CA-MXDK15SP-MXDK15FSP-MXDK15F
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Contents
Block diagrams
Standard schematic diagrams
Printed circuit boards
CA-MXDK3SP-MXDK3FSP-MXDK3FSP-MXDK3W
COPYRIGHT 2006 Victor Company of Japan, Limited.
2-1
2-2
2-11 to 14
No.MB515SCH
2006/6
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the
parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "
mark nearby are critical for safety.