JVC MP-XV941DE, MP-XV841DE, MP-XV841GB, MP-XV841GBEX, MP-XV841US Service Manual
SERVICE MANUAL
Mobile mini note PC
XE00320047
MP-XV941DE, MP-XV841DE,
MP-XV841GB,MP-XV841GBEX,
MP-XV841US
Area Suffix
DE ---------- Germany
GB --------------- U.K.
US ------------- U.S.A.
TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
COPYRIGHT © 2004 Victor Company of Japan, Limited
No.XE003
2004/7
SECTION 1
PRECAUTION
This service manual does not describe PRECAUTION.
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS.
1-2 (No.XE003)
SECTION 3
A
A
DISASSEMBLY
3.1 Disassembly procedure
3.1.1 Removing the DIMM cover(See Figure 1)
(1) Remove three screws A from the DIMM cover on the bot-
tom of the main unit.
(2) Remove the DIMM cover by lifting it up from the gap a.
3.1.2 Removing the DVD drive unit(See Figure 2)
• Prior to the following procedure, DIMM cover should be removed.
(1) Remove two screws B, which are attached to the DVD
drive unit, from the bottom of the main unit.
(2) Push part b in the direction indicated by the arrow, then pull
out the DVD drive unit by sliding outward.
Part b
Gap a
A
DIMM Cover
Fig.1
B
DVD Drive unit
Hole c
B
Fig.2
3.1.3 Removing the fitting(See Figure 2, Figure 3)
• Prior to the following procedure, DVD drive unit should be
removed.
(1) Eject the tray by inserting a piece of fine wire into the small
hole c.
(2) Disengage three tabs d, and then disengage one hook e.
* Pay special attention not to damage either the tabs or
the hooks.
Hook e Fitting
Tab dTab d
Fig.3
DVD Drive unit
Tab d
(No.XE003)1-3
3.1.4 Removing the keyboard assembly(See Figure 4 , Figure 5,Figure 6)
f
1
2
1
Removes
Attach
(1) Individually push three latches f in the upper part of the key-
board with a single-slotted or flat screwdriver, and then lift
the keyboard assembly upward.
Latch f
Latch f
Keyboard
Fig.4
1
1
Attach
Attach
222
2
Removes
Removes
1
Latch
(2) Pull out the card wires from the connectors CON6
CON8 on the main board respectively.
and
Fig.5
Main board
Keyboard CON8
CON6
Fig.6
1-4 (No.XE003)
3.1.5 Removing the hinge cover(See Figure 7 ,Figure 8, Figure 9)
(1) Remove one screw C and two screws B from the hinge
cover.
C :short D :long
(2) Disconnect one card wire from the connector CON5
main board.
on the
D
CON5
(3) Remove one screw E from the bottom of the main unit.
(4) Leave the LCD panel open. Release four tabs g on the
hinge cover by slowly inserting a single-slotted or flat
screwdriver into the slot of the battery terminal.
*Please make sure not to damage either the hinge cover or the bottom case when releasing the tabs.
(5) Slowly remove the hinge cover in the direction indicted by
the arrow.
Hinge cover
Tab g Tab g
D
C
Fig.7
E
Fig.8
Bottom case
Tab g
Tab g
Hinge cover
LCD Panel assemblyBattery terminal
Fig.9
(No.XE003)1-5
Loading...