JVC LVT1627-001A User Manual

HDD NAVIGATION/DVD RECEIVER

NAVEGACIÓN HDD/RECEPTOR DVD SYSTÈME DE NAVIGATION À DISQUE DUR/RÉCEPTEUR DVD

KD-NX5000

FRANÇAIS ESPAÑOL ENGLISH

For installation and connections, refer to the separate manual. Para la instalación y las conexiones, refiérase al manual separado. Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.

Model No.

Serial No.

LVT1627-001A

[J]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to

obtain the best possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

ENGLISH

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave

all servicing to qualified service personnel.

3. CAUTION:

(For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

If you need to operate the unit while driving, be sure to look ahead carefully or you may be involved in a traffic accident.

Caution:

Never try to analyse or retrieve the data stored in the Hard Disk Drive (HDD). Otherwise, you may have your warranty invalid, and be penalized by law. The manufacturer assumes no liability for any damage resulting from such conduct as mentioned above.

Caution:

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

Every time you turn on the unit, the screen below appears. Take enough care when operating the unit and make sure safe driving.

CAUTION!

DRIVER IS RESPONSIBLE FOR DRIVING DECISIONS AND KEEPING EYES ON THE ROAD! Please see owner’s manual for complete safety instructions.

WARNINGS: To prevent accidents and damage

• DO NOT install any unit in locations where:

– it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety

devices such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving. If you need to operate the unit while driving, be sure to look ahead carefully.

• The driver must not watch the monitor while driving.

• If the parking brake is not engaged,

Parking Brake

“ and no playback picture will be shown.

– This warning appears only when the

parking brake wire is connected to the parking brake system built in the car (refer to the Installation/Connection Manual).

” flashes on the monitor,

Hard Disk Drive (HDD)

Installation

This unit has a built-in HDD, which is a device to read minute magnetic changes. The inside of the device is precision components, requiring you to notice the following when installing the unit: Install the unit at a place where the following conditions are satisfied:

• Dry and neither too hot nor too cold— between 5°C (41°F) and 35°C (95°F).

If the temperature is too low, the HDD will not work. Wait until the temperature in the car becomes normal before operating the unit.

• At an altitude between –300 m (–980 ft) below sea level and +3000 m (9800 ft) above sea level.

• With adequate ventilation to prevent internal heat buildup in the unit.

Before using HDD

While the unit is turned on, the hard disk is constantly rotating at a high speed. This requires you to notice the following:

• DO NOT impart vibration or shock.

• DO NOT allow anything having strong magnetism or emitting strong electromagnetic waves (cellular phones, etc.) near the unit.

• DO NOT disconnect the power cords from the car battery when the unit is turned on.

Failure in following the above cautions may damage the HDD (the stored data will be lost and be never restored).

When the temperature is low, the HDD may take some time to start up, or may reboot automatically.

It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.

How to reset your unit

ENGLISH

• Your preset adjustments will also be erased.

How to forcibly eject a disc

If a disc cannot be recognized by the unit or cannot be ejected, eject the disc as follows.

[Hold]

How to detach/attach the control panel

Detaching

Attaching

Emergency Eject

) appear on the monitor.

Press 5 / ∞ repeatedly to select

, then press ENT.

Eject

• If this does not work, reset your unit.

• Be careful not to drop the disc when it ejects.

and

No Eject

(or

Eject

Emergency

Cautions on the monitor:

• The monitor built in this unit has been produced with high precision, but it may have some ineffective dots. This is inevitable and is not malfunction.

• Do not expose the monitor to direct sunlight.

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on

a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/

TV technician for help.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

[European Union only]

Contents

ENGLISHENGLISH

8 Introduction

18 Navigation system

Initial settings Basic operations Parts index Remote controller—RM-RK250

Basic operations Registering your home Starting guidance Searching for a place How you are guided Arranging your route Registering favorite points Traffic information on map Navigation menu items

51 Radio

Listening to the radio Listening to the satellite radio

59 Discs and HDD

Disc operations Music server operations CD changer operations

79 Other functions

iPod/D. player operations Playing other external components Using Bluetooth devices AV Menu items Sound equalization

109 Troubleshooting

117 Specifications

Initial settings

When you turn on the unit for the first time, the initial setup screen appears. Follow the procedure below and make necessary settings.

ENGLISH

Adjust the following settings.

Language

Store Display Mode

Turn on the power.

Language

English US

Español Français

Select an item

Proceed to the next setting

Back to the previous setting

Select the language you want for the display and the voice guidance.

Select

Off

• If you select the navigation demonstration mode for shops. (☞ [47])

, the System starts in

DST

Select

Auto

if your residential area is

subject to DST (Daylight Saving Time).

Reverse Polarization

Engage the parking brake, step on the brake pedal, then switch the gear lever.

Forward

If on the display, connection is correct. Select one of the alternatives (

Battery

correctly.

and

Reverse

) that shows the gear position

alternates

Finish the procedure.

GND

Installation Angle

Select which angle your unit is installed at. This setting is necessary for the precise functioning of the Navigation System.

• See “Measuring the installation angle” on the Installation/Connection Manual.

Time Zone

Select your residential area for clock adjustment.

You can also change these settings (except

Store Display Mode

Menu and

Language

•

Installation Angle

•

Time Zone

•

DST

•

Reverse Polarization

•

AV Menu

☞ [46]

☞ [91]

) through

when necessary.

☞ [46]

Setup

☞ [94]

Calibration

Before using the Navigation System first time, it is required to calibrate the Navigation System.

• After deleting the calibration data (☞ [46] angle (☞ [46]

Installation Angle

Reset Calibration

), calibration is also required.

) or changing the installation

1 Display the map screen.

2 Display the detail screen and check the

connections.

[Hold]

Calibrating... Detail

GPS Antenna

• OK ] Connection is OK. ( satellites whose signal is detected.)

] Antenna is disconnected or short-circuited.

•

[5]

: number of the GPS

Speed Signal

Drive the car for a while.

• If the number increases as you speed up the car, connection is OK.

Parking Brake

Step on the brake pedal, then disengage and engage the parking brake repeatedly.

Off

appears when disengaged and On appears when engaged, connection is OK.

• If

If the result is not good, check the connection.

• You can see detailed information on the items of

Connection

. (☞ [43])

Sensor Status

Learning Lv. :0 GPS Antenna :OK [5] Speed Signal :12.0 Parking Brake :On Direction :Forward

Calibrating...

: Calibration not in

progress.

: Calibration in progress.

Information

]

3 After confirming all the above connections, drive the car to start

calibration.

• This process can take five minutes or more depending on the average speed driven.

• A certain speed (greater than 25 mi/h (40 km/h)) is required for calibration.

• Calibration time differs among the cars.

• During calibrating, you can use the AV functions of the unit (you can listen to the music, etc.)

• If you turn off the ignition switch, calibration is temporarily stopped. When it is turned on, calibration will restart.

Once calibration is finished, the arrowhead icon turns red and the current position information appears instead of calibration finished.

Navigation (functions such as guidance or route simulation) cannot be used until calibration is complete.

Calibrating.... Learning Lv.

(maximum level is 4) reaches 1 after

Initial settings

Basic operations

ENGLISH

Reset the unit.

• Use only when the internal system malfunctions.

To turn on the power

To turn off the power

[Hold]

To drop the volume in a moment (ATT)

ATT indicator flashes.

To restore the sound, press the same button again.

To adjust the volume

To change the source

TUNER = SAT* = DISC* = HDD = CD-CH/ EXT-IN/iPod/D. PLAYER*

(Back to the beginning)

* You cannot select these sources if they are not

ready.

Bluetooth Audio*

To turn off the AV function

[Hold]

The display switches to the map screen.

• To activate the AV function, press the button briefly.

For navigation operations,

For radio operations,

For disc/HDD operations,

For Bluetooth operations,

For other sources, ☞

☞ [18] ☞ [51] ☞ [59] ☞ [83]

[79]

. . . . .

To switch between the map screen and AV screen

Map screenAV screen

You can always switch between the AV screen and the map screen. This switching does not affect the playback sound of the unit (except while recording an Audio CD) or the guidance function of the Navigation System.

To change the display of AV screens

AV screen

FM1

Station name

92.5 MHz

Distance to the next turn/Turn icon (While not guided: Speed/ Direction)

Current time The built-in clock is automatically adjusted by receiving the GPS signals.

Vehicle information

(☞

[35]

)

AV screen 1

* The number and contents of AV screens depend on the source. ** Appears only when you have selected Video or Camera for Video Input setting (

AV screen 2

How to change the control panel angle

[Hold]

Tilt 1 Tilt 2 Tilt 3 Tilt 4

Caution: Do not insert your finger behind the control panel.

☞ [93]

Video input

(

☞ [82]

)

11Basic operations

Menu operations

To call up a menu

Navigation Menus AV Menu

ENGLISH

Map screen AV screen

FM1

Station name

92.5 MHz

Destination 1/2

Home Return

Address

Vicinity Previous

Information Menu ☞ [42]

Information 1/2

Current Position

Traffic Turns List Trip Destination

Setup Menu ☞ [43]

Setup 1/2

Guidance Voice

Guidance Options Route Options Map Color Map Options

AV Menu

☞ [90]Destination Menu ☞ [42]

AV Menu 1/2

Setup

EQ Sound Screen Control Aspect

To navigate through menus

Press: Select a menu item Hold: Skip to the first menu

item on the next page

Proceed to the next menu

Back to the previous menu

To go back to the previous screen and adjust other items:

To cancel menu operations and return to the map screen or the AV screen:

Menu screen

Current menu title

Remaining time until the

menu screen goes off.

(Appears only on AV Menu.)

Display 1/2

Language

Demonstration

Wall Paper Scroll Tag Display

Current setting of the

[Off]

selected item.

Menu items

• If items are displayed in gray, you cannot use them now.

On some screens, special operations are indicated here with the button to use.

Ex.:

Delete

: Button to press : Button to press and hold

• When no icon is displayed here, ENT button functions the same as

In this manual, operation of selecting a menu item is instructed as in the example below.

Ex.:

AV Menu

]

Current page number/ Total page number

Selected menu item Button icons indicate the

available operations in each screen.

button.

]Pop

1 Call up 2 Select

AV Menu

AV Menu 1/2

[Flat]

EQ 1/3

Exit

AV Menu

Setup

Sound Screen Control Aspect

Flat

Hard Rock R&B Pop Jazz

3 Change the setting as you like.

EQ 1/3

Flat Hard Rock R&B

Pop

Jazz

Exit

Now the setting is changed. Press DISP to exit from the menu, or BACK to go back to the previous menu.

13Basic operations

Parts index

ENGLISH

AV/SRC

MAP/POS

TRAFFIC

463

pqwe

On the map screen On the AV screens On menu screens

• Turn on the unit.

/ATT

+/–

/DISP

• Turn off the unit if pressed and held.

• Attenuate/restore the sound.

Switch to the AV screen. • Change the source.

Turn off the AV function if pressed and held.

• Change the map view.

• Display your current position after scrolling the map.

Adjust the volume.

Call up Destination Menu.

☞ [42]

Call up Phone Menu if pressed and held.

Enter the scaling mode.

Display the Traffic List.

☞ [40]

Switch to the map screen.

Call up AV Menu.

☞ [83]

Change the display.

(Not used)

☞ [90]

☞ [11]

In Navigation Menus: Switch to the AV screen. In AV Menu: Change the source and switch to the AV screen.

In Navigation Menus: Switch to other menus. In AV Menu: Go back to the top screen of AV Menu or switch to the AV screen.

Exit from the menu.

5/∞

/BACK

7/BAND

ENT/3/

On the map screen On the AV screens On menu screens

FM/AM: Select preset stations. Satellite radio: Select categories. DVD: Select titles/groups. Files: Select folders.

• Operate the current source.

☞ [50]

• Change the map scale.

☞ [22]

• Scroll the map.

• Open/close the control panel.

• Change the control panel angle if pressed and held.

• Enter the manual scrolling mode.

☞ [22]

• Repeat the last voice guidance if pressed and held during guidance.

Call up Shortcut Menu.

☞ [25]

Detach the control panel.

☞ [22]

☞ [33]

Music server: Select albums. iPod/D. player:

Enter the main menu.

∞

Pause/resume playback.

Bluetooth Audio: Select a device.

FM/AM: Search for stations. Satellite radio: Search for channels. Disc, Music server, iPod/D. player, Bluetooth Audio: Select tracks/ chapters.

Tuner: Select the bands. Disc: Stop playing.

Disc: Start playing. Confirm the selection.

Select an item.

Go back to the previous screen.

Remote controller—RM-RK250

Installing the batteries

R03(UM-4)/ AAA(24F)

Before using the remote controller:

• Aim the remote controller directly at the remote sensor on the unit.

Remote sensor

Parts index / Remote controller—RM-RK250

Caution:

• If the range or effectiveness of the remote control decreases, replace both batteries.

• Do not expose batteries to heat or flame.

The unit is equipped with the steering wheel remote control function.

• See the Installation/Connection Manual (separate volume) for connection.

• DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting).

Operations from the remote controller

On the map screen On the AV screens On menu screens

ENGLISH

AV/OFF

MAP/POS

TRAFFIC

ENT 6

PHONE

BACK/BAND

/7/

VOL +/–

5/∞

+/–

HOME

ATT

DISP

Switch to the AV screen. • Change the source.

Turn off the AV function if pressed and held.

• Change the map view.

• Display your current position after scrolling the map.

Call up Destination Menu.

☞ [42]

Display the Traffic List.

☞ [40]

Call up Shortcut Menu.

☞ [25]

Scroll the map (in eight directions).

Call up Dial Menu when a Bluetooth phone is connected.

Repeat the last voice guidance if pressed and held during guidance.

Adjust the volume.

Scale the map. (Not used)

Start guidance to a home.

☞ [24]

Attenuate/restore the sound.

Enter the scaling mode.

In Navigation Menus: Switch to the AV screen. In AV Menu: Change the source and switch to the AV screen.

Switch to the map screen.

In Navigation Menus: Switch to other menus.

Call up AV Menu.

(Not used)

Disc: Start playing/pause. Confirm the selection.

FM/AM: Select preset stations. Satellite radio: Select categories. DVD: Select titles/groups. Files: Select folders. Music server: Select albums. iPod/D. player:

Enter the main menu.

∞

Pause/resume playback.

Bluetooth Audio: Select a device. FM/AM: Search for stations.

Satellite radio: Search for channels. Disc, Music server, iPod/D. player, Bluetooth Audio: Select tracks/ chapters.

Tuner: Select the bands. Disc: Stop playing.

(Not used)

Change the display.

☞ [90]

☞ [11]

In AV Menu: Go back to the top screen of AV Menu or switch to the AV screen.

Select an item.

☞ [86]

Go back to the previous screen.

Start guidance to a home.

☞ [24]

Exit from the menu.

y u i

DVD MENU

o ;

RETURN DIRECT/

ASPECT

Number

1/¡

ENT

TOP M

OSD

CLEAR

keys

Only on the AV screens

• Make selections in disc menus.

• DISC +/– buttons: Change discs for a CD changer.

Disc: Confirm the selection.

DVD/DivX 6: Show the disc menu. VCD with PBC: Resume PBC playback.

Display the on-screen bar.

VCD with PBC: Return to the previous menu.

Disc: To select a chapter/title/group/folder/track directly.

Disc: Change the aspect ratio of the playback pictures.

Disc: To select a chapter/title/group/folder/track directly. Tuner: Select a preset station. Satellite radio: Input a channel number directly or select a preset channel. CD changer: Select a disc. Bluetooth phone: Input telephone number.

Disc: Reverse search/forward search. Slow playback if pressed while paused.

Disc: Select audio languages/audio channels.

Disc: Select subtitles.

Disc: Select a view angle.

☞ [67]

☞ [68]

☞ [67]

☞ [66]

☞ [87]

12 34

5 89

ui t

w r

Slide to open

f ghj

These buttons do not function at this position.

Remote controller—RM-RK250

Navigation System

ENGLISH

20 Safety instructions for

Navigation System

22 Basic operations

24 Registering your home

To register your home To go home

26 Starting guidance

Setting a destination using Shortcut Menu Setting a destination using Destination Menu To go back to where you started

28 Searching for a place

By address POI near a place/route From last destinations From the list of POI From your favorites By telephone number By coordinates

32 How you are guided

24 24

26 27 27

28 29 30 30 31 31 31

Getting information on your route and places Customizing how you are guided

34 35

36 Arranging your route

Setting places to stop by Saving and loading routes Avoiding a congestion ahead

38 Registering favorite points

Marking your favorite points Editing your favorite points

40 Traffic information on map

What is TMC? Checking the traffic information How traffic information is reflected in navigation Subscribing to traffic service

42 Navigation menu items

Destination Menu Information Menu Setup Menu

36 37 37

38 38

40 40 41 41

42 42 43

46 Remote operations

47 Additional information

1919

Safety instructions for Navigation System

SAFETY INSTRUCTIONS

Use of the Navigation System is only permitted

ENGLISH

if the traffic conditions are suitable and you are absolutely sure that no risk, obstruction or inconvenience will be incurred to you, your passengers or other road users. The requirements of the Road Traffic Regulations must always be followed. The destination must

not be entered while driving the car.

The Navigation System serves solely as an aid to navigation. It never releases the drivers from their duties to drive carefully and to make own judgement in road traffic. Inaccurate or incorrect instructions may happen to be given due to changing traffic conditions. The actual road signs and traffic regulations must therefore always be observed. In particular, the Navigation System cannot be used as an aid to orientation when visibility is poor. This Navigation System must only be used for its intended purpose. The volume of the car radio/Navigation System must be adjusted so that external noise is still audible.

Navigation guidance is performed, based on the database, therefore, it may not be applicable to the current situation because of changes in traffic conditions (e.g. changes in tollroads, principal roads, one-way traffic, or other traffic regulations). In this case, observe the current traffic signs or regulations.

• Traffic signs should be observed carefully while driving using the Navigation System. Navigation System is only an aid. Driver must always decide whether or not to heed the information provided. JVC does not accept

liability for erroneous data provided by the Navigation System.

• Traffic guidance is restricted to passenger vehicles only. Special driving recommendations and regulations for other vehicles (e.g. commercial vehicles) are not included.

• Do not operate the unit while driving.

Terms of licence

You are granted a non-exclusive licence to use the database for your personal purposes. The present licence does not authorise the granting of sublicenses. Use of the data is only permitted in this specific JVC system. It is forbidden to extract or make further use of significant parts of the database content, or to duplicate, modify, adapt, translate, analyse, decompile or reverseengineer any part thereof.

WARNING:

Road traffic regulations always take priority when a vehicle is being driven in traffic. Navigation System is only an aid. Errors may occur in individual data items/entries. At all times, the driver must decide whether or not to heed the information provided. JVC does not accept liability for erroneous data provided by the Navigation System.

When replacing/rotating the tires:

It is required to clear all the accumulated learning data which is important for accurate navigation. To clear the data, perform

Calibration

on page 46.

Reset

On map updating

If “Your map data is more than one year old and updates may be available.” appears on the monitor, visit <http://www.jvc-exad.com>. For details about updating your unit, visit <http://www.jvc-exad.com>.

Safety instructions for Navigation System

Basic operations

Current position mode

—The map scrolls automatically so that your position is always at the center of the map.

ENGLISH

Switch to the AV screen.

Adjust the volume.

Your position

Scale

Call up a menu screen.

Show traffic information. (

Scale the map.

☞ [40]

)

Change the map view. (

current position.

)/Display your

☞

To scroll the map

The map scrolls in eight directions.

• Press and hold the button to keep scrolling the map.

Direction and distance from your current position

Current time

Current street name

Scroll the map.

Operate the current AV source. (

Call up Shortcut Menu.

To change the map scale

To display your current position

Zoom in

Zoom in rapidly

Zoom out Zoom out rapidly

☞ [50]

Scale bar

)

To change the map view

To call up menus

Navigation Menus

The map view changes as follows:

Heading Up = 3D Map = North Up

Heading Up

The map rotates so that you are always displayed heading “upwards.” The direction

]

Map

is displayed with a compass icon

3D Map

The map is displayed in “heading up” and in a three-dimensional view. The direction is displayed with a compass icon

North Up

The map view is oriented with north “upwards,” like usual paper maps. The direction you are heading to is displayed at the upper right corner of the screen with an

icon such as

You can also change the map view through

Setup

Menu ]

(☞ [45]).

View

Map Options

Each time you press the button, the menu switches as follows:

(Map screen)

Destination Menu

= Information Menu

Setup Menu

(Back to the map screen)

Menu operations ☞ [13] Menu items ☞ [42 – 46]

Shortcut Menu

Shortcut Menu appears. ☞ [25]

Icons on the map

Favorite points (

POI (Point Of Interest) (

Traffic (

• Favorite icons are displayed on the map when a group is selected in the setting (☞ [45]) and the map scale is between 100 ft (30 m) and 1.2 mile (2.0 km).

• POI icons are displayed on the map when a group is selected in the [45]) and the map scale is 100 ft (30 m) or 160 ft (50 m).

• Traffic icons are displayed on the map when

Traffic Display

the (☞ [45]) and the map scale is between 100 ft (30 m) and 1.2 mile (2.0 km).

☞ [38 – 39]

☞ [40, 50]

)

Favorite Icon

POI Icon

setting is activated

)

☞ [30, 49]

setting (☞

)

23Basic operations

Registering your home

To register your home

ENGLISH

• You can register homes only after calibration

is finished. (☞ [9])

1 If you are at home now, check

that your home is displayed at the center of the map.

• Adjust the position by scrolling the map if necessary.

2 Call up Shortcut Menu.

3 Select [Add to Favorite] .

The home is marked with icon.

To go home (

When you have registered your home, you can easily get guided to home.

While not guided...

Home

)

1 Call up Shortcut Menu.

2 Select [Go Home] to start

guidance.

• If you have registered several homes, select the one you want to go to from a list.

On the remote:

4 Select [Set Home] .

The home is marked with icon.

• The icon may not appear depending on

Home

Favorite Icon

. (☞ [38, 39])

the map scale and your setting. (☞ [45])

• You can register several places as Home by registering the places as favorite points and setting their group to

You can also be guided to home through

Destination

Menu ]

Home

To cancel guidance

1 Call up Shortcut Menu.

2 Select [Cancel Guidance] .

You can also cancel guidance through

Destination

Menu ]

Cancel Guide

What is Shortcut Menu?

On the map screen, you can call up Shortcut Menu by pressing ENT. Shortcut Menu is a gateway to various operations.

Shortcut Menu

Map screen

While not guided

To select an icon, press ENT or one of the four keys on the right circle button corresponding to the icon.

While guided

Icon Name Function Button

View Information

Go Home

Set Home

Cancel Guidance

Add to Favorite

Edit Favorite

Show information on this place. ☞ [35]

Start guidance to a home. ☞ [24] (Not selectable if no home is registered.)

Cancel the guidance. ☞ [24]

Add this place to your favorite points. ☞ [38]

Edit this favorite point. ☞ [39] (Appears only when a favorite icon is selected. Not selectable while driving.)

Vicinity

Go Here

Add to Via Point

Search for POI around this place. ☞ [29]

Start guidance to this place. ☞ [26]

Recalculate the route to stop by this place. ☞

[36] (Appears only while guided.)

25Registering your home

Starting guidance

• You can set destinations only after calibration is finished. (☞ [9])

ENGLISH

Setting a destination using Shortcut Menu

Scroll the map to display the destination at the center of the

map.

Call up Shortcut Menu.

Select [Go Here] to start guidance.

The System starts calculating the route to the selected destination, and guidance starts.

To cancel guidance

1 Call up Shortcut Menu.

You can also cancel guidance through

Destination

Menu ]

2 Select [Cancel Guidance] .

Cancel Guide

Setting a destination using Destination Menu

Call up Destination Menu.

Select one of the methods to search for your destination.

Destination 1/2

Home* Return** Address Vicinity Previous

* During guidance, Cancel Guide appears. ** During guidance, Avoid Section appears.

• You cannot select the items when they are gray.

The information on the search result appears.

Direction and distance from

your current position

☞ [24] ☞ [below] ☞ [28] ☞ [29] ☞ [30]

0.7 mi

Destination 2/2

POI Favorite Telephone Coordinates

Route Edit

To see the search result on map

☞ [30] ☞ [31] ☞ [31] ☞ [31]

Select [Go Here] to start guidance.

The System starts calculating the route to the selected destination, and guidance starts.

To go back to where you started (

You can go back to the start point of the last guidance.

Return

)

1 Call up Destination Menu.

Destination

]

Return

Starting guidance

Searching for a place

To input names, addresses, or numbers

Ex. Input screen for a city name

ENGLISH

MoreBS

Enter a space

Delete the last character

* You can also change the keyboard by pressing

DISP. For available charactears,

** Buttons vary depending on the input item.

Display other keyboards*

1 Enter characters.

Move the cursor on the keyboard

Enter the selected character

• Available characters are automatically narrowed down as the System searches its database for matches.

2 Display the list of matches.

Display the list of

matches

☞ [105].

3 Select the item you want from the

list.

By address (

Address

)

1 Call up Destination Menu.

Destination

]

Address

New York

City Street

3 Input the state name.

• Input the city name if a state is already selected.

- Input State Name -

AllBS

• This button is available when the matches are narrowed down to 100 or less.

• You can also display the list of matches by pressing and holding ENT.

• When the matches are narrowed down to 5 or less, the list appears automatically.

Displays the list of all the states.

4 Input the city name.

- Input City Name -

BS More Street

Select this to search by street

name.

• Inputting characters ☞ [left column]

5 Input the street name.

• You can also select the center of the city. (The list of city centers may appear.) You do not have to input the house number in this case.

• Select the area to search from the list if

Select Area

is displayed.

6 Input the house number.

• You can also select the entire street or an intersection on the street.

• If no data of house number for the selected street is available in the database, this step is skipped.

POI near a place/route (

You can search for a POI around the place where you are now. While guided, you can also search for a POI near the destination or along the route.

Vicinity

)

1 Call up Destination Menu.

Destination

]

Vicinity

Select Category 1/3

All Categories

Gas station

Hotel Parking Restaurant

Area: Local Change

While guided, select the area to search if necessary.

[Hold]

Select Area

Local Area

Near Destination Along Route

Local Area

your current position. If no POI is found in this area, the System expands the area to search.

Near Destination

of the destination. If no POI is found in this area, the System expands the area to search.

Along Route

route you are taking.

: within 1.2 mi (2 km) of

: within 1.2 mi (2 km)

: 30 mi (50 km) along the

3 Select a category (then a sub

category if any)

The result is listed in the order of distance from the place where you are.

of the POI.

Select Category 1/3

All Categories

Gas station

Hotel Parking Restaurant

Area: Local Change

4 Select a POI from the list.

You can search for a POI around a place on the map through Shortcut Menu ]

[Vicinity]

above after selecting

. Follow steps 3 and 4

[Vicinity]

Searching for a place

From last destinations (

From the list of POI (

)

POI

)

You can select a place from the last 50 destinations and via points.

ENGLISH

1 Call up Destination Menu.

Destination

]

The list of previous destinations/via points is displayed.

3 Select a place from the list.

To delete items in the list of previous destinations/via points

1 After step 2 above...

2 Check the boxes of the items you

want to delete.

• Checkbox operations ☞ [105]

A confirmation message appears. Press ENT to confirm the operation. Press BACK to cancel.

[Hold]

The System has a huge database of POI (Point Of Interest), such as restaurants, gas stations, hospitals, etc.

1 Call up Destination Menu.

Destination

]

POI

New York

City Category Name

3 Input the state name.

• Input the city name if a state is already selected.

4 Input the city name.

• Inputting characters ☞ [28]

5 Select a method to search for a

POI with.

You can search for a POI in two ways:

By category and name Directly by name

POI

New York New York(New York)

Category Name

+ 222 hidden pages