JVC LVT1238-002A, CS-VS601 User Manual

Specifications

Type : 16 cm (6-1/2") 2-Way Component Speaker, Door/

rear mounting Power Handling Capacity : 150 watts (MAX. MUSIC POWER) Impedance : 4 ohms Magnet Mass : 256 g (9 oz) Mass : 0.87 kg (2.00 lbs)

(Design and specifications are subject to change without notice.)

If a kit is necessary for your car, consult your telephone directory for the nearest car audio speciality shop ("IN-CAR ENTERTAINMENT" dealer)

CS-VS601

CAR STEREO SPEAKER

CS-VS601

Thank you for purchasing the JVC Car Stereo Speakers. These speakers can be mounted either in the doors or in the rear tray of your vehicle. For the secure installation and perfect operation of your speakers, please read the following carefully.

For Proper Installation and Use

1. Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the connection if the power is on may damage the speakers.

2. The amplifier and speakers should be connected between corresponding terminals, i.e. "left" to "left", and "right" to "right", as well as "+" to "+", and "-" to "-". Connection with reversed polarity will degrade the quality of stereo reproduction.

3. Do not subject the speakers to excessive input. The power handling capacity of the CS-VS601 is 150 watts (Max. music power). Any excessive input may damage the speakers.

4. The CS-VS601 has an impedance of the amplifier's speaker terminal is rated at 4 ohms.

5. When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.

INSTRUCTIONS

LVT1238-002A

Dimensions

42.4

18.5 9

48.8

-O4

O50.5 O58.8

O49.8

O179.3

27.3

Q/YXFJ105

JVC

(Victor Company of Japan, Limited)

JVC

43.8 21.9

O80

O124

UNIT : mm

How to Install

1. To install the speaker in the rear tray, first determine the appropriate area in which to place it. The speakers must be installed in a place where there are spaces of at least 32 mm over the tray and at least 49 mm under the tray. ln determining the location, make sure that the bottom part of each speaker fits into the large hole in the steel plate on which the rear tray is

fixed.

2. Remove the rear tray.

3. The paper pattern printed on the bottom of the packing box shows the exact shape of the area on the rear tray through which the speaker will be installed. Apply the paper pattern onto the area determined in 1. above, and trace out the shape of the area on the tray.

4. Then, cut out the marked area.

5. The next step is to wire the speakers. Be sure to connect to connect corresponding terminals, i.e.

"left" to "left", "-" to" -", etc.

6. Use the tapping screw and speed nuts provided to fix the speaker and grille to the rear tray. Match

the 4 screw holes in the speaker frame and the grille to the holes in the rear tray, insert the 4 screws in into the holes and secure them with 4 nut.

7. The process for installing the speakers in the door is much the same as for installing the speakers in the rear tray. ln this case, however, extra care must be taken to install the speaker out of the way of the door handle. lnstall the speakers with the terminals down.

Tweeter level adjust

2-WAY

CRO

SSOVER NE

12dB/

TWORK

Oct.

INPUT

WOOFER

TWE

ETER

-3dB 0dB

(-3dB)

(-0dB)

Woofer Mounting

-3dB 0dB

Tweeter Mounting

Swivel Mounting

Flush Mounting

Angle Mounting

Surface Mounting

Network Mounting

INPUT

WOO

2-WAY CR

OSSOVE

R NET

/Oct.

TWEETER

2-W

OVER NETW

/Oct.

ORK

INPUT

OOFER

TWEETER

Connection

Amplifier

Woofer

Black lined

Parts

2-WAY CROSSOVER NETWORK

12dB/Oct.

Screw

1 2

(O4x25mm)

Network cord

Screw

(O4x20mm)

Screw

(O3.5x20mm)

Speaker cord

8 9

Screw

(O4x25mm)

Screw nut

(O4mm)

Speaker cord

Speed nut

x16

(O4 mm)

Amplifier

WOOFERINPUT TWEETER

Midwoofer

Tweeter

2m 2m4m

Grille Ass'y

10 11

Network

2-WAY CROSSOVER N

INPU

WOOFE

dB/Oct.

ETW

ORK

TWEETER

Mounting bracket

Angle adaptor

Fix frame

x2 x2

Tweeter