JVC LVT1220-002A User Manual

Download

MICRO COMPONENT MD SYSTEM MD 微型组合音响

UX-QD7M

Consists of CA-UXQD7M and SP-UXQD6M 由 CA-UXQD7M 和 SP-UXQD6M 组成

UX-QD7W

Consists of CA-UXQD7W and SP-UXQD6W 由 CA-UXQD7W 和 SP-UXQD6W 组成

English

中

文

For hiding the demonstration display, refer to page 16.

有关隐藏演示显示的详情，请参阅

16 页。

第

INSTRUCTIONS

使用说明书

LVT1220-002A

[UB]

Introduction

Warnings, Cautions and Others

警告，注意及其他须知事项

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

1. Do not remove screws, covers or cabinet.

2. Do not expose this appliance to rain or moisture.

CAUTION — F button!

Disconnect the mains plug to shut the power off completely. The F button in any position does not disconnect the mains line. The power can be remote controlled.

CAUTION

• Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)

• Do not place any naked flame sources, such as lighted candles, on the apparatus.

• When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly.

• Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

IMPORTANT FOR LASER PRODUCTS / 镭射产品的重要说明

注意

为了减少触电、火灾等危险：

1. 请勿擅自卸下螺丝钉、盖子或机壳。

2. 请勿让本机受雨淋或置于潮湿环境中。

注意－ F 开关！

想要完全关闭电源，须将电源插头从插座上拔下。无论 F 键处于何种位置，主电路仍旧没有关闭。电源开关可用遥控器进行控制。

注意

• 切勿堵塞通风口或通风孔。（如果通风口或通风孔被报纸或布等物堵塞，热量将无

法散出。）

• 切勿在本系统上放置明火，如点燃的蜡烛。

• 想要丢弃电池时，务必考虑环保问题以及严格遵守当地

关于处理废旧电池相关的法律规定和条例。

• 切勿让本机受雨淋、受潮湿、落上或溅上水滴，亦勿在

本机上面放置盛满液体的容器，如花瓶。

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and invisible laser radiation when open and interlock failed or defeated. Avoid direct exposure to beam.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED INSIDE THE UNIT.

1. 一级镭射产品。

2. 注意：请勿打开顶盖板，本机内部没有用户可自行维修

的部件；所有维修工作应由有资格的人员完成。

3. 注意：当内部锁定装置失效或者损坏后，打开盖板可能会产生可见或不可见的镭射辐射。应避免受到镭射光束的直接照射。

4. 标签的复制标示：注意标签位于机内。

G-1

CAUTION — Proper Ventilation

To avoid risk of electric shock and fire and to protect from damage, locate the apparatus as follows: Top/Front/Back/Sides: No obstructions should be placed in

Bottom: Place on the level surface. Maintain

In addition, maintain the best possible air circulation.

Front view

前视图

15cm

the areas shown by the dimensions below.

adequate air path for ventilation by placing on a stand with a height of 10 cm or more.

Main unit

本机

1cm

15cm

1cm

注意 — 正确的通风方法

为了防止触电，火灾及避免损坏，按如下要求放置机器：上面 / 前面 / 后面 / 侧面：在图中所示范围中，不应放置任何障

底部：放置在水平面上。放置在一个高

此外，如图所示，尽可能保持最佳的空气循环。

碍物。

或更高的台上以保留足够的通风道。

Side view

侧视图

15cm

Main unit

本机

Wall or

obstructions

墙壁或障碍物

10cm

15cm

10 cm

Front

前面

G-2

marks refer to operation used frequently. You can quickly learn the general usage of this

product by reading those parts only.

Introduction

Notes on Operation ............................. 3

Suitable Locations for the Main Unit ................. 3

Condensation.................................................... 3

Cleaning the Main Unit ..................................... 3

Listener’s Etiquette ........................................... 3

Playable Disc Types ......................................... 4

Disc Structure ................................................... 5

Selecting the Color System .............................. 6

Special Cautions.................................. 7

Notes on Handling ............................................ 7

Supplied Accessories ....................................... 7

Preparation

Part Description ................................... 8

Remote Control ................................... 9

Inserting Batteries into the Remote Control...... 9

Operating the TV Using the Remote Control.... 10

Connections.........................................11

Connecting the Antennas ................................. 11

Connecting the Speakers ................................. 13

Connecting Other Equipment ........................... 14

Connecting with a TV........................................ 15

When a Clearer Picture Is Desired ................... 15

Connecting the Power Plug .............................. 16

Basic Operations

Basic Operations .................................17

Setting the Clock............................................... 17

Turning On/Off the Main Unit...... 18

Adjusting the Volume .................. 18

Temporarily Turning Off the Sound

(FADE MUTING).......................................... 18

Emphasizing Heavy Bass Sound (AHB PRO).. 18

Adjusting the Sound Quality ............................. 18

Changing the Color Patterns for the Display

Window and Disc Tray ................................. 19

Listening to Radio Broadcasts

.............................................. 20

Setting the AM Tuner Spacing.......................... 20

Selecting a Radio Station ................................. 20

Storing Radio Stations (Preset) ........................ 21

Tuning In to a Preset Radio Station.................. 21

Changing the Display in the Display Window ... 21

Listening to Discs

Basic Operations of the DVD Player ... 22

Playback ..................................... 22

Changing the Display in the Display Window... 24 Playing Back from a Position 10 Seconds

Before (One Touch Replay) ......................... 24

Stopping Playback...................... 25

Resuming Playback (RESUME) ....................... 25

Pausing Playback ............................................. 25

Advancing Picture Frame by Frame................. 25

Fast Reverse/Fast Forward

Search ................................... 25

Slow Motion Playback ...................................... 26

Skipping to the Beginning of

a Track................................... 26

Skipping to the Beginning of a Track with

the Number Buttons..................................... 26

Selecting a Track from the Menu Screen ......... 26

Convenient Functions of the DVD

Player ................................................27

Selecting the Audio..................... 27

Selecting the Subtitle ........................................ 28

Selecting a View Angle..................................... 28

Magnifying the Picture (ZOOM)........................ 28

Adjusting the Picture Quality (VFP) .................. 29

Creating Realistic Sound (3D PHONIC)........... 29

Adjusting Playback Level (DVD LEVEL) .......... 30

Enjoying Better Pictures (PROGRESSIVE)...... 30

Playing Back the Bonus Group......................... 31

Browsable Still Pictures (B.S.P.) ...................... 31

Playing Back the Disc in the Desired Order

(Program Playback) ..................................... 32

Random Playback ............................................ 33

Repeat Playback .............................................. 34

Status Bar and Menu Bar .................... 35

Using the Status Bar and Menu Bar ................. 35

Playing Back the Designated Part Repeatedly

(A-B Repeat Playback) ................................ 36

Designate the Time (Time Search)................... 36

Playing Back MP3/WMA and JPEG

Discs..................................................37

Playback ........................................................... 37

Repeat Playback .............................................. 38

Preferences .........................................39

Basic Operations .............................................. 39

LANGUAGE...................................................... 39

PICTURE.......................................................... 39

AUDIO .............................................................. 40

OTHERS........................................................... 40

Country/Area Codes............................41

Language Codes .................................42

Listening to Cassette Tapes

.............................................. 43

Changing the Display in the Display Window

..................................................................... 44

Listening to Other Equipment

Listening to Other Equipment ..............45

Adjusting the Sound Input Level from

Other Equipment.......................................... 45

Changing the Display in the Display Window ... 45

Listening to MDs

Listening to MDs..................................46

Listening to MDs ......................... 46

Changing the Display in the Display Window ... 47 Specifying the Track (Direct Track Selection)... 47

Group Playback of an MD................................. 47

Program Playback ............................................ 48

Random Playback............................................. 48

Repeat Playback............................................... 49

Searching Titles ................................................ 49

Editing MDs

Giving (Editing) Titles ..........................58

Things You Should Know about Editing ........... 58

Giving (Editing) Titles ....................................... 58

Entering Titles................................................... 59

Available Characters ........................................ 59

Editing Tracks......................................60

Dividing a Track into Two Tracks (DIVIDE)...... 60

Joining Tracks (JOIN)....................................... 61

Moving a Track (MOVE) ................................... 61

Erasing a Track (ERASE) .......... 62

Erasing All Tracks

(ALL ERASE)......................... 62

Editing Tracks by Group......................63

Forming a Group (FORM GR) .......................... 63

Adding a Track to a Group (ENTRY GR) ......... 64

Dividing a Group into Two Groups

(DIVIDE GR) ................................................ 64

Joining Groups (JOIN GR) ............................... 65

Moving a Group (MOVE GR)............................ 65

Canceling a Group (UNGROUP/UNGR ALL)... 66

Erasing a Group (ERASE GR) ......................... 67

Convenient Functions

English Introduction

Recording Sound

Recording Sound to

..................................... 51

MDs

Recording All Tracks from a Disc to an MD...... 51

Quitting Recording ............................................ 52

Recording Only One Track from a Disc ............ 52

Recording the Second or Subsequent Track

to the Last Track from a Disc ....................... 52

Program Recording from a Disc ....................... 52

Things You Should Know about

MD Recording .............................................. 53

Recording Sound from Radio, Cassette Tape

or Other Equipment...................................... 53

Quitting Recording ............................................ 54

Recording Sound to Cassette Tapes

.............................................. 55

Quitting Recording ............................................ 56

Recording Only One Track from

a Disc or MD ................................................ 56

Recording the Second or Subsequent Track

to the Last Track from a Disc or MD ........... 56

Program Recording from a Disc or MD............. 56

Recording with No Blank Time between

Tracks .......................................................... 56

Erasing Recorded Sound from

a Cassette Tape........................................... 56

Using the Timers .................................68

Sleep Timer ...................................................... 68

Recording Timer ............................................... 68

Playback Timer................................................. 70

Auto Standby.......................................72

Disc/MD Ejection Lock ........................72

Using AV COMPU LINK ......................73

Connection and Setting .................................... 73

Operations ........................................................ 73

Reference

Restrictions on MDs ............................ 74

Serial Copy Management System (SCMS) ...... 74

Handling Discs/MDs/Cassette Tapes.. 75

MD/Disc Messages .............................76

Troubleshooting...................................77

Specifications ......................................78

Introduction

Notes on Operation

Introduction

Suitable Locations for the Main Unit

To minimize the need for servicing and maintain the high quality of this product, do not place the main unit in the following locations:

• In a position subject to high humidity or considerable dust

• On an uneven or unstable surface

• Near a heat source

• Near a computer, fluorescent light or other electric appliance

• In a small room with insufficient ventilation

• In a position exposed to direct sunlight

• In a position exposed to excessive cold

• In a position exposed to strong vibration

• Near a TV, other amplifier, or tuner

• Near a magnetic source

CAUTION

• The operating temperature of this product is 5°C to 35°C. Use in temperatures outside this range may cause a malfunction or damage the product.

Condensation

Under the following conditions, you may not be able to operate this product properly due to condensation formed on the lens of the main unit:

• When you have just started an air conditioner to warm your room

• When you have placed the main unit at an area with high humidity

• When you have moved the main unit from a cold place to a warm place

When condensation forms, leave the main unit turned on, wait for approximately 1 or 2 hours, and then operate the main unit.

Cleaning the Main Unit

When the operation panel becomes dirty, dust it with a soft dry cloth. When the operation panel is very dirty, wipe it with a cloth dampened with a small amount of a neutral detergent, and then wipe it with a soft dry cloth.

CAUTION

• Do not wipe the operation panel with thinners, benzenes or other chemical agents. Do not spray insecticides onto the operation panel. These may cause discoloration and damage to the surface.

Listener's Etiquette

When using headphones, keep the volume at a moderate level so as not to over-stimulate your ears.

■When enjoying sound from the speakers, adjust the volume to a suitable level to avoid disturbing your neighbors. Even low-volume sound carries a long way, especially at night. Show consideration to your neighbors by closing windows or using headphones.

• Manufactured under license from Dolby Laboratories. "Dolby", "MLP Lossless", and the double-D symbol are trademarks of Dolby Laboratories.

• "DTS" and "DTS 2.0+DIGITAL OUT" are registered trademarks of Digital Theater Systems, Inc.

• This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

Playable Disc Types

This product has been designed to play back the following discs: DVD VIDEO, DVD AUDIO, VCD, SVCD, CD This product can also play back the following discs:

• Finalized DVD-R/RW discs recorded in the DVD VIDEO format.

• CD-R/RW discs recorded in the following formats

- Music CDs (finalized discs)

- VCDs

- SVCDs

- MP3/WMA/JPEG discs recorded in ISO 9660 (for details, refer to "About MP3/WMA/JPEG discs") However, some discs may not be played back because of their disc characteristics, recording conditions, or damage or stain on them. Only sounds can be played back from the following discs:

MIX-MODE CD CD-G CD-EXTRA CD TEXT

Discs you can play:

Disc Type Mark (Logo)

DVD

VIDEO

DVD

AUDIO

VCD

SVCD

CD — —

CD-R — —

CD-RW — —

Video

Format

PAL /

NTSC

PAL /

NTSC

PAL /

NTSC

DVD Logo is a trademark of DVD Format/Logo Licensing Corporation.

* Note on Region Code

DVD players and DVD VIDEOs have their own region code numbers. This product can only play back a DVD VIDEO recorded with the region code number and video format mentioned above.

Examples:

Region

Code

Number*

3/ALL

——

—

• On some DVD VIDEOs, DVD AUDIOs, VCDs or SVCDs, their actual operation may be different from what is explained in this manual. This is due to the disc programming and disc structure, not a malfunction of this product.

About CD-Rs/CD-RWs

You can play back a CD-R/CD-RW only when the disc is finalized.

• You can play back a CD-R/CD-RW which has been recorded in the audio CD format and a CD-R/CD-RW to which audio data (MP3/WMA) or a still picture data (JPEG) file is recorded. However, playback is impossible in some cases due to the disc characteristics, recording condition, scratches or dirt on the disc, or dirt or condensation on the lens.

• Before using a CD-R/CD-RW, carefully read the cautions regarding the disc.

• This product does not support playback or CD text display of sound files such as MP3s.

• To play back a CD-RW on this product, erase all tracks if the CD-RW was recorded in a format other than the audio CD format. Using the CD-RW without erasing all tracks may result in damage to the speakers or other parts caused by sudden loud volume.

Discs that cannot be played back

• The following discs cannot be played back: DVD-ROM, DVD-RAM, DVD-RW (recorded in VR format), CD-ROM, CD-I (CD-I Ready), Photo CD, SACD, etc. Playing back these discs will generate noise and damage the speakers.

• Damaged discs and discs in an extraordinary shape (other than a disc of 12 cm or 8 cm in diameter) cannot be played back.

• JVC do not guarantee the operation and sound quality of discs not authorized by CD-DA, which is a CD specification. Before playback, confirm that the disc complies with this CD specification by checking the marks and reading notes printed on the package.

English Introduction English

If a DVD VIDEO with an improper region code number is loaded, "REGION CODE ERROR!" appears on the TV screen and playback cannot start.

(Continued) Notes on Operation

About MP3/WMA/JPEG discs

Playable MP3/WMA/JPEG discs and files

• Discs recorded in the ISO 9660 format are playable (except discs recorded in the "packet write" format (UDF format)).

• Discs recorded in the multi-session format are also playable.

• Files with an extension of ".mp3", ".wma", ".jpg" or ".jpeg" (extensions with uppercase and lowercase letters mixed are also acceptable) are playable.

Introduction

Disc Structure

DVD VIDEO

A DVD VIDEO consists of "titles" and each title may be divided into "chapters".

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 3 Chapter 1 Chapter 2

Notes on MP3/WMA/JPEG discs and files

• A disc may not be played back, or reading it may take a long time depending on its recording conditions or properties.

• The time needed for reading varies with the number of groups or tracks (files) recorded on the disc.

• If a character other than single byte English characters is used in the file name of an MP3/ WMA/JPEG file, the track/file name will not be displayed correctly.

• The order of tracks/groups displayed on the MP3/WMA Control screen, and the order of files/ groups displayed on the JPEG Control screen may be different from that of files/folders displayed on PC's monitor screen.

• In the case of MP3/WMA discs, since groups/ tracks are played back in alphabetical order, an off-the-shelf MP3/WMA disc may be played back in an order different from that indicated on the label attached to the disc.

• Playing back an MP3/WMA file including a still image may take a long time. The elapsed time is not displayed until playing back starts. If playing back starts, the elapsed time may not be displayed correctly.

• For an MP3/WMA file, a disc with a sampling frequency of 44.1 kHz and transmission rate of 128 kbps is recommended.

• This product is not compatible with MP3i or MP3PRO.

• This product can play back a baseline JPEG file, excluding monochromatic JPEG files.

• This product can play back JPEG data taken with a digital camera conforming to the DCF (Design Rule for Camera File System) standard (when a function is applied such as the automatic rotation function of a digital camera, data goes beyond the DCF standard, so the image may not be displayed).

• If data has been processed, edited and restored with PC image editing software, the data may not be displayed.

• This product cannot play back animations such as MOTION JPEG, or still pictures (TIFF etc.) other than JPEG, and image data with sound.

• The resolution of 640 x 480 pixels is recommended for JPEG files. If a file has been recorded at a resolution of more than 640 x 480 pixels, display may take a long time. An image with a resolution of more than 8 192 x 7 680 pixels cannot be displayed.

• Files recorded on DVD-R/RW discs cannot be played back.

DVD AUDIO

A DVD AUDIO consists of "groups" and each group may be divided into "tracks". Some discs include a "bonus group" that requires

a password for playing ( page 31).

Group 1 Group 2

Track 1Track 2Track 3Track 1Track 2

VCD/SVCD/CD

VCD, SVCD and CD consist of "tracks". In general, each track has its own track number. (On some discs, each track may also be further divided by indexes.)

Track 1Track 2Track 3Track 4Track 5

MP3/WMA [JPEG] discs

On an MP3/WMA [JPEG] disc, each still picture (material) is recorded as a track [file]. Tracks [Files] are usually grouped into a folder. Folders can also include other folders, creating hierarchical folder layers. This unit simplifies the hierarchical construction of a disc and manages folders by "groups".

Up to 99 groups

Group 1 Group 2

Track 1

[File 1]

Track 2

[File 2]

Up to 150 files

Group 3 Group 4 Group 5

This product can recognize up to 1 000 tracks [files] in a disc. Also, the product can recognize up to 150 tracks [files] per group and up to 99 groups in a disc. Since the unit ignores the tracks [files] whose numbers are exceeding 150 and the groups whose numbers are exceeding 99, they cannot be played back.

• If there is any type of files other than MP3/WMA [JPEG] files in a disc, those tracks [files] are also counted in the total file number.

Selecting the Color System

This product is compatible with PAL and NTSC color systems. In standby mode, select PAL or NTSC to match your TV. If the VIDEO OUT SELECT switch is switched over when the power is on, turn off the power, and then turn it on again.

English Introduction English

• Before playing back a disc, it is also required to select the correct MONITOR TYPE in the PICTURE menu according to the aspect ratio of

your TV ( page 39).

NOTE

• If you play back an NTSC disc with this setting set to "PAL", you can watch the playback pictures (the disc will be reproduced using "PAL 60" format), but the TV screen may rolls over upward and downward rapidly.

NOTE

• If you play back a PAL disc with this setting set to "NTSC", you can watch the playback pictures, but the following symptoms may occur:

• The items on the disc menu will be blurred, and

be shown slightly shifted when highlighted.

• The aspect ratio of the picture may differ from

the original aspect ratio.

• The picture movement is not smooth.

Special Cautions

Notes on Handling

■ Important cautions

Installation of the system

• Select a place which is level, dry and neither too hot nor too cold; between 5°C and 35°C.

• Leave sufficient distance between the system and the TV.

• Do not use the system in a place subject to vibration.

Power cord

• Do not handle the power cord with wet hands!

• A small amount of power is always consumed while the power cord is connected to the wall outlet.

• When unplugging the power cord from the wall outlet, always pull on the plug, not the power cord.

To prevent malfunctions of the system

• There are no user-serviceable parts inside. If anything goes wrong, unplug the power cord and consult your dealer.

• Do not insert any metallic object into the system.

• Do not use any non-standard shape disc (like a heart, flower or credit card, etc.) available on the market, because it may damage the system.

• Do not use a disc with tape, stickers, or paste on it, because it may damage the system.

Label sticker

Introduction

Avoid high temperatures

Do not expose the system to direct sunlight and do not place it near a heating equipment.

When you are away

When away on travel or for other reasons for an extended period of time, disconnect the power cord plug from the wall outlet.

Do not block the vents

Blocking the vents may damage the system.

Care of the cabinet

When cleaning the system, use a soft cloth and follow the relevant instructions on the use of chemically-coated cloths. Do not use benzene, thinner or other organic solvents including disinfectants. These may cause deformation or discoloring.

If water gets inside the system

Turn the system off and disconnect the power cord plug from the wall outlet, then call the store where you made your purchase. Using the system in this condition may cause fire or electrical shock.

■When condensation or water drops adhere to the lens

In any of the following cases, condensation or water drops may adhere to the lens to prevent the system from working properly:

• Immediately after roomheating starts

• When the system is installed in a steamy or damp space

• When the system is suddenly moved from a cold place to a warm space

In any of these cases, leave the system turned on for 1 or 2 hours before use.

Stick er

Paste

Note about copyright laws

Check the copyright laws in your country before recording from CDs. Recording of copyrighted material may infringe copyright laws.

■ Safety precautions

Avoid moisture, water and dust

Do not place the system in moist or dusty places.

Supplied Accessories

Check to be sure you have all of the supplied accessories. The number in parentheses is the quantity of the pieces supplied. If anything is missing, contact your dealer immediately.

Remote control (1) Batteries (2) FM antenna (1) AM loop antenna (1) Video cord (1)

Introcution/Preparation

Part Description

The numbers refer to the pages in which the parts are explained.

20 22 23

46, 51

43, 55

16, 19

Remote control sensor: 9

68, 70 18 72 32, 33, 34,

48, 49

22 44

46 20, 45

English Introcution/Preparation English

18 29

Cassette holder: 43 PUSH-OPEN

MD slot: 46

25, 43, 4651

* This terminal is for connecting a pair of headphones equipped with a stereo mini plug (not supplied). While

the headphones are connected, the speakers do not produce any sound.

Disc tray: 22

Remote Control

Preparation

The numbers refer to the pages in which the parts are explained.

Introduction

Inserting Batteries into the

Remote Control

25, 43, 46

47, 64

21, 23, 27, 58

17, 69 21, 24, 44, 45, 59

21, 58, 65, 70

33, 58, 59, 62-67

20, 32, 47, 48

43, 55

25, 43, 46

25, 26

17, 21, 26, 32, 59

34, 49

58-62

58, 63-67

29, 30

R6P (SUM-3) /AA (15F) type dry-cell batteries (2)

CAUTION

• Do not use a used battery and a new battery together.

• Do not use different types of batteries at the same time.

• Take out the batteries if the remote control is not to be used for a long time. Otherwise it may cause a leakage.

Opening the cover

Remote control operation

• When operating the remote control, point it at the front panel of the main unit.

• The effective distance between the remote control and the remote control sensor on the main unit is approximately 5 m maximum.

• When the effective distance decreases, replace the batteries.

• Do not drop the remote control or subject it to excessive shock.

This page is for when operating your TV using the remote control of this product.

Operating the TV Using the Remote Control

Remote control mode selector

Number buttons

4 Press number buttons (1-9, 0).

Examples:

For a Hitachi TV: Press 1, then 0.

For a Toshiba TV: Press 0, then 8. If there are two or more manufacturer's codes, try them in turn and select the one that causes the product to work properly.

Manufacturer Code Manufacturer Code

JVC 01 Samsung 12

Hitachi 10 Sanyo 13

Magnavox 02 Sharp 06

Mitsubishi 03 Sony 07

Panasonic 04, 11 Toshiba 08

Philips 14 Zenith 09

RCA 05

5 Release .

NOTE

• The manufacturer's codes may be changed without notice. You may not be able to operate a TV produced by the manufacturer shown above.

For TV operation

English Preparation English

Setting the manufacturer's code

1 Slide the remote control mode

selector to the TV side.

2 Hold down .

NOTE

• Hold down until step 4 is completed.

3 Press and release.

Operate the remote control by pointing it towards the TV.

Turn on/off the power.

Change channels.

Adjust volume.

- /

Change between the previously selected channel and the current channel.

Change between TV and video input.

*1 Make sure to slide the remote control mode selector

to the TV side in advance.

NOTE

• When the batteries are replaced, perform the manufacturer's code setting again.

Select channels.

Introduction

Connections

Connect all necessary parts before connecting the power plug.

Connecting the Antennas

Connecting the AM antenna

1 Set up the AM antenna (supplied).

Insert the tab into the slot.

2 Connect the antenna cord.

Main unit (side view)

Main unit (rear view)

■When radio reception with the supplied AM loop antenna is poor

Vinyl-covered wire: 3 - 5 m (not supplied)

Twist together vinylcovered wire and the AM loop antenna cord.

Main unit (rear view)

Stretch out the vinylcovered wire horizontally, preferably in a high place such as above a window or outdoors. Connect the AM loop antenna cord to the main unit together with the vinyl-covered wire.

Connecting the antenna cord

When insulation covers the tips of the antenna cord, twist and pull off

Connect the ends of the antenna cord as shown above.

the insulation.

3 Turn the AM loop antenna to find

the best position for radio reception. Place the AM loop antenna as far from the main unit as possible.

• Do not place the AM loop antenna on a metallic table or close to a TV, computer, or other electric appliances. Doing so may affect radio reception.

When positioning the antennas, find the best position for reception while listening to an actual radio program (refer to "Listening to Radio Broadcasts" ( page 20)).

English Preparation English

Connecting the FM antenna

Main unit (rear view)

FM antenna (supplied)

Main unit (side view)

Stretch out the FM antenna to the best position for radio reception, and then fix it with adhesive tape.

■When radio reception with the supplied FM antenna is poor, or when using a communal antenna

Main unit (side view)

Main unit (rear view)

Antenna cord (not supplied)

When using an antenna other than those supplied with this product, refer to the operation manuals for the antenna for details of connection.

Communal antenna terminal

Outdoor FM antenna (not supplied)

Coaxial cable (not supplied)

When positioning the antennas, find the best position for reception while listening to an actual radio program (refer to "Listening to Radio Broadcasts" ( page 20)).

(Continued) Connections

Connecting the Speakers

Main unit (rear view)

Speaker cord

Introduction

Connect all necessary parts before connecting the power plug.

After connecting the speakers, gently pull on the speaker cords to make sure the cords are firmly connected and do not pull out.

Speaker cord

Red

Black

Right speaker (rear view)

CAUTION

• Do not short-circuit the and speaker terminals. Doing so may damage the speakers.

• Do not connect other speakers together with the supplied speakers. The change in impedance may damage the main unit and the speakers.

• The speakers of this product are magnetically shielded, but color irregularities may occur on the TV depending on how the speakers are installed. Keep in mind the following.

1. Turn off the main power of your TV before

installing the speakers. Wait for about 30 minutes before turning on the TV again.

2. If color irregularity occurs in pictures, keep a

distance of more than 10 cm between the TV and the speakers.

Red

Black

Left speaker (rear view)

You can detach the speaker cover.

NOTE

• Improper speaker cord connection spoils the stereo effect and sound quality.

• The impedance of speakers connected to this product must be within the range of 4 Ω to 16 Ω.

• Cooling fan is built into the main unit for emitting generated heat. The internal cooling fan automatically rotates and stops. To ensure sufficient cooling, leave a space of more than 1 cm between the main unit and the speakers or other objects.

Speaker cord

Speaker cover

Connecting Other Equipment

Read this section when connecting other audio equipment to this product.

Connecting with digital equipment

AV amplifier with a built-in

decoder (not supplied)

To an optical digital input terminal

English Preparation English

Other audio

equipment

Audio cord (not supplied)

CAUTION

• Before connecting other equipment, turn off both the main unit and the equipment.

Optical digital cable (not supplied)

From an optical digital input terminal

MD player or CS tuner

(not supplied)

CAUTION

• For details of signals to be output, refer to page 40.

• If connecting the main unit to equipment that has the function of a Dolby Digital decoder, the setting in "D. RANGE COMPRESSION" of "AUDIO" ( page 40) will be invalid regarding sound from the digital audio output of the main unit.

(Continued) Connections

Introduction

Connect all necessary parts before connecting the power plug.

Connecting with a TV

VIDEO IN

CAUTION

• Connect the main unit directly with a TV (or a monitor) without routing through a VCR. Otherwise it may cause picture distortion while playing back. (Such picture distortion is caused by a copy protection system, and thus it is not a malfunction.)

Main unit

Also, if the main unit is connected to a TV with a built-in VCR, there may be picture distortion during playback.

NOTE

• Please check that the setting for VIDEO OUT SELECT (PAL/NTSC) on the rear panel of the main unit and the color system on your TV set are the

same. ( page 6) You need to set "MONITOR TYPE" in the "PICTURE" menu correctly according to the aspect

ratio of your TV. ( page 39)

Supplied video cord

VCR

Connecting directly

VIDEO

(or monitor)

Main unit

Connecting by using the component video cord

You can enjoy better quality pictures than when using the S-video cord.

Component video cord (not supplied)

Main unit

CAUTION

• Use one of either the S-video cord or the component video cord. If both cords are used, pictures may not be played back properly.

When a Clearer Picture Is Desired

You can enjoy pictures of better quality using the following cord instead of the supplied video cord.

Connecting by using the S-video cord

Connect the ends of S-video cord making sure that each end matches its compatible terminal.

S-video cord (not supplied)

Main unit

S-VIDEO

NOTE

• In order to enjoy pictures with the progressive mode ( page 30), the TV is required to have

progressive video input.

• If the component video input jacks of your TV are BNC type, use a plug adapter (not supplied) to convert the plugs.

Connecting the Power Plug

English Preparation English

AC outlet

• After making all other necessary connections, connect in the power plug.

NOTE

• The preset setting such as preset channels and sound adjustment may be erased in a few days in the following cases:

- When you disconnect the power plug.

- When a power failure occurs.

Main unit (rear view)

Demonstration display function

When you connect the power plug into the AC outlet, "DEMO START!" appears in the display window and the demonstration display starts.

When you press on the main unit, "DEMO

OFF" appears in the display window and the demonstration display is canceled. Turning on the main unit automatically cancels the demonstration display.

Resuming the demonstration display

With the power turned off, press on the main

unit.

Hiding the demonstration display

With the power turned off, hold down

until "DEMO CLEAR" appears. Disconnecting and then reconnecting the power plug does not start the demonstration display. To activate the demonstration display again,

hold down until "DEMO START!"

appears.

Basic Operations

Introduction

This manual explains the operations assuming that you will use the remote control. Some buttons on the main unit are the same as those on the remote control. You can use either button in this case.

Remote control mode selector

Number buttons

2 Set the hour.

Back Next

• Holding down the button causes the hour to increment.

• You can use the number buttons to specify the hour. Refer to "Using the number buttons" shown below.

Using the number buttons

Set the remote control mode selector to AUDIO before using the number buttons.

Examples:3:

13: → 20: → 23: → →

3 Press .

CAUTION

• Set the remote control mode selector to AUDIO before using the number buttons.

Setting the Clock

You can set the clock while the main unit is turned either on or off.

Example: To set the clock to 10:10 a.m.

1 Press .

• To return to step 2, press .

4 Set the minute in the same manner

as steps 2 and 3.

Adjusting the clock

Press four times to display the clock, and then adjust the clock starting from step 2.

Displaying the clock while using the main unit

Press repeatedly.

NOTE

• The time display on the main unit is a 24-hour clock.

• The clock will gain or lose approximately 1 minute per month.

• Set the clock again after you have disconnected the power plug or a power cut has occurred.

Turning On/Off the Main Unit

Press (or on the main unit).

• With the power off, pressing either button also turns on the main unit. The function assigned to the button starts working at the same time.

Remote control:

Main unit:

NOTE

• Cooling fan is built into the main unit for emitting generated heat. The internal cooling fan automatically rotates and stops.

Adjusting the Volume

Press .

• You can also adjust the volume by turning

the VOLUME control on the main unit.

NOTE

• You can adjust the volume within the range of 0 to

40.

Adjusting the Sound Quality

Selecting the sound mode

Press .

• Each time you press , the display tog-

gles as follows.

: For emphasizing treble

and bass sounds.

: Adequate for songs

and narrations.

: For emphasizing treble

sound.

: For uplifting a feeling

of being at a live performance.

: For adjusting treble and

bass sounds of your choice (shown below).

: Cancels the sound

mode (initial setting).

• While the sound mode is set to an item other

than "FLAT", is displayed in the display window.

NOTE

• This function does not affect recording sound.

English Basic Operations English

Temporarily Turning Off the Sound (FADE MUTING)

Press .

• "FADE MUTING" appears and the volume

reduces to "0".

• To return to the previous volume, press

again.

Emphasizing Heavy Bass Sound (AHB PRO)

Press .

• Each time you press , AHB PRO

function toggles between "ON" and "OFF".

• While AHB PRO function is activated, is displayed in the display

window.

• "AHB PRO" stands for "Active Hyper

Bass PRO".

Adjusting bass/treble sound

1 Press repeatedly to display

"MANUAL".

2 For adjusting bass sound;

Press . For adjusting treble sound;

Press .

• You can adjust the sound quality within the range of -5 to +5.

• The display returns to the sound source display in a few seconds.

NOTE

• While the sound mode is set to an item other than "MANUAL", "NO OPERATE" is displayed in the display window and you cannot adjust bass/treble sound.

(Continued) Basic Operations

Changing the Color Patterns for the Display Window and Disc Tray

Press (or on the main unit).

• Each time you press , the display toggles as follows.

: For a rainbow-like

pattern.

: For a flower-image

pattern.

: Gradually changes

the color pattern in a cycle of approximately 20 seconds.

: For an ocean-image

pattern.

: For a fantasy pattern.

Introduction

For the locations of remote control buttons, refer to page 17.

3 Press to adjust the intensity

of the component color.

• You can also adjust the color intensity by turning the VOLUME control on the main unit.

• You can adjust the color intensity within the range of "0" to "3". You cannot set all three component colors (red, green, and blue) to "0" at the same time.

NOTE

• After you have adjusted each component color, the display returns to the sound source display in approximately 8 seconds.

• You cannot set different colors for the display window and disc tray.

• When you operate a button on the main unit or remote control, the display window and disc tray light in pale blue for approximately 2 seconds.

• When recording finishes, the color of the display window and disc tray switches to the color set in "MANUAL" to inform you that recording has finished. (With an item other than "MANUAL" selected) When you operate the main unit after recording finishes, the color pattern for the display window and disc tray returns to the selected pattern.

: For the color of your

choice. (The setting shown on the left is initial setting.)

Setting your favorite color for the display window and disc tray

1 Press repeatedly to display

"MANUAL".

2 Press or to select a

component color.

• Numerical value of the selected component color flashes.

Changing the brightness of the display window and disc tray (DIMMER)

Press .

• Each time you press , the display toggles as follows.

: Color pattern becomes

dimmer.

: Color pattern

becomes darker, and switches to blue.

: DIMMER 2 is automat-

ically selected during video playback, and is canceled when the playback stops.

: Cancels the brightness

adjustment (initial setting).

NOTE

• Once you press to change the color pattern, the brightness returns to the initial setting. (except

for DIMMER AUTO)

• When you turn off the main unit, the brightness also returns to the initial setting.

• You cannot turn off the color pattern.

Basic Operations/Listening to Rad io Broadcasts

Listening to Radio Broadcasts

This product can receive FM and AM radio broadcasts.

Remote control mode selector

Number buttons

■When the main unit is turned off

To select 10 kHz spacing, while holding down

on the main unit, press on the main unit to turn on the power. "AM 10 kHz" appears in the display

window.

To select 9 kHz spacing, while holding down on

the main unit, press on the main unit to turn on the power. "AM 9 kHz" appears in the display

window.

NOTE

• If the spacing is switched, the memory in which the radio stations were stored will be erased.

Selecting a Radio Station

1 Press repeatedly to select

"FM" or "AM".

Example: Display while an FM radio broadcast

is received

Stereo indicator

Preset number ( page 21)

English Basic Operations/Listening to Radio Broadcasts English

CAUTION

• Set the remote control mode selector to AUDIO before using the number buttons.

Setting the AM Tuner Spacing

Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing.

On the main unit ONLY:

Frequency

2 Press or repeatedly to

select a radio station (frequency).

• You can also select a radio station using the automatic tuning.

Automatic tuning:

Hold down or until the frequency starts changing, and then release

the button. When the main unit has received a broadcast, the frequency automatically stops changing. To quit the function while searching for a

broadcast, press or .

• When the main unit has received an FM stereo broadcast, "STEREO" lights up.

NOTE

• If an FM stereo broadcast is difficult to hear because of noise, you may be able to hear more

easily by pressing to switch the sound to monaural reception. In this case, "MONO" lights up. To return the sound to stereo reception, press

again or select another FM radio station.

• This product is not compatible with AM stereo broadcasts.

(Continued) Listening to Radio Broadcasts

Introduction

For the locations of remote control buttons, refer to page 20.

Storing Radio Stations (Preset)

You can store up to 30 FM radio stations and up to 15 AM radio stations.

■ While the broadcast from the radio station you want to preset is being received

1 Set the remote control mode

selector to AUDIO.

2 Press .

• The preset number flashes for approximately 5 seconds.

3 While the preset number is flash-

ing, press the number buttons (

- or ) to select the preset

number you want to use.

• Refer to "Using the number buttons" ( page 17).

4 While the selected number is

flashing, press .

• "STORED" appears and the selected radio station is stored.

NOTE

• When you store a radio station to a preset number to which another radio station has previously been stored, the newly set radio station replaces the previously stored radio station.

Tuning In to a Preset Radio Station

■ While an FM or AM broadcast is being received

1 Set the remote control mode

selector to AUDIO.

Entering radio station names

You can enter the name of a stored radio station using up to 8 characters.

1 Set the remote control mode

selector to AUDIO.

2 Press . 3 Entering a radio station name with

or the number buttons ( -

• To enter radio station names, refer to "Entering Titles" ( page 59).

4 Press .

• "STORED" appears in the display window and the entered radio station name is registered.

NOTE

• When you store a radio station after you have entered a radio station name, the entered radio station name with the same preset number is erased.

• You cannot enter radio station names after

selecting a radio broadcast with or .

• If you change the AM tuner spacing ( page 20), radio station names remain unchanged. Enter radio station names again, if necessary.

Changing the Display in the Display Window

Press .

• Each time you press , the display tog-

gles as follows.

Display while a radio broadcast is being

received ( page 20)

2 Use the number buttons to select

the preset number of the radio station to which you want to tune in.

• Refer to "Using the number buttons" ( page 17).

(Time display)

Clock display

(With an MD loaded) Display of remaining time for MD recording

Listening to Radio Broadcasts/Listening to Discs

Basic Operations of the DVD Player

How to read this manual

• Operations are described by mainly using the remote control buttons. If there are the same marks on the main unit, the buttons on the main unit can also be used.

• The following marks tell you for which type of the discs the operation can be made.

• The illustrations and TV screens may be different between the actual case and the description.

• "VCD" stands for "Video CD".

• "SVCD" stands for "Super Video CD".

Remote control mode selector

Playback

English Listening to Radio Broadcasts/Listening to Discs English

(Refer to page 37 for playing back MP3/WMA and JPEG.)

1 Press on the main unit.

• The disc tray comes out.

2 Place a disc on the disc tray.

Letter-printed surface

Disc tray

• When you want to listen to an 8 cm disc, place it on the inner hollow of the disc tray.

3 Press .

■Display for DVD VIDEO

Display while a DVD VIDEO is being played back:

DVD indicator (The DVD indicator lights up while the DVD VIDEO is stopped. The DVD indicator flashes while the DVD VIDEO is being played back or paused.)

Number buttons

NOTE

• Set the remote control mode selector to AUDIO before using the number buttons.

Title number

Chapter number

Elapsed playing time

Display while the DVD VIDEO is stopped:

Total number of titles

(Continued on next page)

(Continued) Basic Operations of the DVD Player

Introduction

■ Display for CD

Display while a CD is being played back:

CD indicator (The CD indicator lights up while the CD is stopped. The CD indicator flashes while the CD is being played back or paused.)

Track number

Elapsed playing time

Display while the CD is stopped:

Total number of tracks

Total playing time

■ Display for DVD AUDIO

Display while a DVD AUDIO is being played back:

DVD indicator (The DVD indicator lights up while the DVD AUDIO is stopped. The DVD indicator flashes while the DVD AUDIO is being played back or paused.)

Group number

Elapsed playing time

Display while the DVD AUDIO is stopped:

Total number of groups

Track number

■Display for VCD/SVCD

Display while a VCD/SVCD is being played back:

VCD indicator (The VCD indicator lights up while the VCD/SVCD is stopped. The VCD indicator flashes while the VCD/SVCD is being played back or paused.)

Track number

Elapsed playing time

• PBC indicator is displayed while PBC is activated.

Display while the VCD/SVCD is stopped:

Total number of tracks (*1, *2)

Total playing time

*1 "1" will appear after the total number of

tracks is displayed.

*2 "PBC" will appear when the disc is PBC-

compatible.

NOTE

• The menu may appear in the display window after DVD playback starts. In such a case, select the desired menu item by using the following buttons on the remote control.

• Select a menu item with , or ,

and then press .

• Select a menu item with the number buttons.

• Operation may differ from the explanation given here, depending on the disc type.

PBC indicator ( page 24)

• "G1" and "T1" will appear after the total number of groups is displayed.

Listening to Discs

For the locations of remote control buttons, refer to page 22.

Messages displayed on the TV screen

While a DVD is selected as the sound source, the messages shown below are displayed, depending on the status.

NOW READING

The main unit is reading the disc. Wait for a while.

REGION CODE ERROR!

The disc cannot be played back because its region code is not compatible. ( page 4)

NO DISC

No disc is loaded.

OPEN

The disc tray is opening.

The disc tray is closing.

CANNOT PLAY

You are trying to play back an unplayable disc.

Guide icons temporarily displayed on the TV screen (on-screen guide)

: Play ( page 22) : Pause

( page 25)

: Fast reverse/Fast forward search ( page 25)

Slow motion playback (reverse/

forward directions)( page 26)

: Containing multi-angle views ( page 28)

: Containing multi-audio ( page 27)

: Containing multi-subtitle ( page 28)

: The disc cannot accept the operation

you have attempted.

PBC (Playback control)

• PBC is a signal recorded in a VCD (version 2.0) for controlling VCD playback. You can operate software that has interactive or search functions using the menu display recorded in a PBC-compatible VCD. To play back a VCD without PBC, follow the operation below.

• Select the desired track number with the

number buttons while playback is stopped.

• While playback is stopped, press

or to select the desired track num-

ber, and then press .

• While a VCD or SVCD is being played

back, press to return to the higher menu group.

Changing the Display in the Display Window

Press .

• Each time you press , the display toggles as follows.

■While a disc is being played back (or stopped)

Display while a disc is being played back or stopped ( pages 22 and 23)

(With an MD loaded)

(Time display)

Clock display

Display of remaining time for MD recording

Playing Back from a Position 10 Seconds Before (One Touch Replay)

English Listening to Discs English

■While a disc is being played back

Press .

NOTE

• This operation may not be carried out for some discs.

• You cannot return to the previous title.

(Continued) Basic Operations of the DVD Player

Introduction

Stopping Playback

■ While a disc is being played back

Press .

Resuming Playback (RESUME)

When playback is stopped in the middle, playback can be started from the stopped scene.

How to suspend playback

■ While a disc is being played back

Perform any of the following operations during playback.

Press once.*

Press to turn off the power.

Change the source to FM/AM or AUX.*

* Even if the power is turned off by pressing

after this, the position where playback has

been stopped will be stored.

Pausing Playback

■While a disc is being played back

Press .

To resume normal playback, press .

• Playback cannot be paused by pressing

on the main unit during JPEG disc slide-show.

Advancing Picture Frame by Frame

(only for moving image)

■While a disc is paused

Press .

• Each time you press , picture will be advanced frame by frame.

• You cannot operate this function with on

the main unit.

Fast Reverse/Fast Forward Search

How to start playback from the stored position

Press .

NOTE

• This function does not work in program playback or random playback.

• The position where playback starts again may be a little different from the stopped position.

• When a disc menu is displayed, the resume function may not work.

• The audio, the subtitle and the angle at that time are stored as well as the stopped position.

• The stored position will be cleared if the disc tray

is opened. Further, if is pressed during

playback, "RESUME" appears. If is pressed at this time, "RESUME" will disappear and the stored information will be cleared.

• Resume function is set to on as the initial preset. You can set the function to off

( page 40).

There are two methods.

■While a disc is being played back

Press or .

• Each time you press or , the speed increases as shown below.

×2 ×5 ×10 ×20 ×60

• To restore the normal speed, press .

Hold down or .

• Fast reverse/fast forward search can be carried out only while the button is pressed.

NOTE

• For a DVD VIDEO, SVCD or VCD, no sound comes out during fast reverse/fast forward search.

• For a CD or DVD AUDIO, sound is intermittent during fast reverse/fast forward search.

For the locations of remote control buttons, refer to page 22.

Slow Motion Playback

(only for moving image)

■ While a disc is paused

Press or .

• Each time you press , the speed increases as shown below.

• Press to pause playback, and press to resume normal playback.

NOTE

• No sound will be produced.

• The picture motion in the reverse direction may not be smooth.

• For a VCD or SVCD, slow motion playback can be carried out in the forward direction only.

Skipping to the Beginning of a Track

2 Press the number buttons ( -

or ) to select the track/chapter you want to listen to.

• Refer to "Using the number buttons" ( page 17).

NOTE

• You can operate a VCD or SVCD while the disc is stopped or played back with PBC off.

• You can operate a DVD AUDIO, CD, MP3, WMA, or JPEG while the disc is either played back or stopped.

• This operation may not be carried out for some discs.

Selecting a Track from the Menu Screen

■While a disc is stopped or being played back*

English Listening to Discs English

1 Set the remote control mode

selector to AUDIO.

■ While a disc is being played back*

Press or .

• Each time you press , the current chapter/track/file skips to the beginning of the

previous chapter/track/file.

• Each time you press , the current chapter/ track/file skips to the beginning of the next

chapter/track/file.

•Press or to select a title or group.

NOTE

* For a VCD or SVCD, this operation can be carried

out only during playback without the PBC function.

• Except for a DVD VIDEO, this operation can also be carried out while the disc is stopped.

• This operation may not be carried out for some discs.

Skipping to the Beginning of a Track with the Number Buttons

■ While a disc is being played back

1 Set the remote control mode

selector to AUDIO.

2 Press or .

• A menu screen of the disc appears.

• Only can be used for DVD AUDIOs.

3 Press (only for a

DVD VIDEO or a DVD AUDIO) or the number buttons to select a track you want to listen to.

• Refer to “Using the number buttons” ( page 17).

• If there are two or more pages of menu

screen, press or to change the pages (only for a VCD or SVCD).

4 Press .

NOTE

* You can operate a VCD or SVCD while PBC is set

to off.

• You cannot perform this function with discs to which a menu screen is not recorded.

• Some disc may start playback even if you do not

press .

Listening to Discs

Introduction

Convenient Functions of the DVD Player

Selecting the Audio

■While a disc containing two or more audio is being played back

Remote control mode selector

1 Press .

Example: TV screen

AUDIO

Selected audio/Total number of audio

Selected audio

Number buttons

NOTE

• Set the remote control mode selector to AUDIO before using the number buttons.

• Each time you press , the audio will be changed. The audio can also be changed by pressing .

AUDIO

2 Wait for a few seconds or press

NOTE

• You can also operate this function by using the menu bar ( page 35).

• For a language code such as "AA", refer to "Language Codes" ( page 42).

• When 2 channel sounds are recorded in 1/2 and multi channel sounds with down-mix prohibited are recorded in 2/2 in a DVD AUDIO, you can select 1/2 only.

Selecting the Subtitle

Selecting a View Angle

English Listening to Discs English

(only for moving image)

■ While a disc containing two or more subtitles is being played back

1 Press .

Example: TV screen

Selected subtitle/Total number of subtitles (When no subtitle is set in the disc, "--" appears.)

Selected subtitle (When no subtitle is set in the disc, "OFF" appears.)

2 Press to select a

subtitle.

3 Wait for a few seconds or press

NOTE

• You can also operate this function by using the menu bar ( page 35).

• For an SVCD, each time you press in step 1, the subtitle type and ON/OFF will be changed.

• For a language code such as "AA", refer to "Language Codes" ( page 42).

• The manner of displaying subtitles may be different depending on the disc.

(only for moving image)

■While a disc containing two or more view angles is being played back

1 Press .

Example: TV screen

Selected view angle/ Total number of view angles

Selected view angle

• Each time you press , the angle will be changed. The angle can also be

changed by pressing .

2 Wait for a few seconds or press

NOTE

• You can also operate this function by using the menu bar ( page 35).

Magnifying the Picture (ZOOM)

(only for moving image)

■While a disc is played back or paused

Canceling the subtitle

Press to select "OFF".

1 Press .

• Each time you press , the picture magnification will be changed (OFF, ZOOM1 - 6).

• When a JPEG disc is used, the picture magnification changes through "ZOOM 1", "ZOOM 2" to "OFF". You cannot change the picture magnification during slide-show playback.

2 Select the portion you want to see

by pressing .

CAUTION

• When you magnify a picture, image quality may be deteriorated or image may be distorted.

(Continued) Convenient Functions of the DVD Player

Adjusting the Picture Quality (VFP)

■ While a disc is played back or paused

1 Press .

Example: TV screen

Current VFP mode

USER1

Setting items

GAMMA : Controls the brightness of neutral

tints while maintaining the brightness of dark and light portions. (Setting range: –3 - +3)

BRIGHTNESS : Controls the brightness of the

display. (Setting range: –8 - +8)

CONTRAST : Controls the contrast of the

display. (Setting range: –7 - +7)

SATURATION : Controls the saturation of the

display. (Setting range: –7 - +7)

TINT : Controls the tint of the display.

(Setting range: –7 - +7)

SHARPNESS : Controls the sharpness of the

display. (Setting range: –8 - +8)

2 Press to select VFP mode.

Introduction

Example:

5 Press to change the

value.

6 Press .

• To adjust other items, go back to step 3.

7 Press .

NOTE

• If no operation is made for several seconds during the procedure, the settings made so far will be automatically stored.

• "VFP" stands for "video fine processor".

Creating Realistic Sound (3D PHONIC)

The two speakers produce an effect resembling surround-sound.

■While a disc is being played back

Press .

Example: TV screen

3D PHONIC

• Each time you press , the display toggles

as follows.

ACTION

DRAMA

ACTION

: Suitable for action movies,

sport programs or other lively programs.

: You can relax with a natural

atmosphere.

NORMAL : For normal playback.

(You cannot adjust the image quality.) → Go to step 7.

CINEMA : Suitable when viewing a movie in

a dim room. (You cannot adjust the image quality.) → Go to step 7.

USER1/USER2: You can adjust the image quality.

→ Go to step 3.

3 Press to select an item

you want to adjust.

4 Press .

THEATER

OFF

• While 3D phonic is activated, is displayed in the display window.

NOTE

• 3D phonic is effective for both the speakers and headphones.

• When noise is produced or sound is distorted, set

3D PHONIC" to "OFF".

• You cannot operate some types of DVD AUDIO discs.

: You can enjoy the sound

effect as if you were watching the movie in a theater.

: Cancels 3D phonic (initial

setting).

For the locations of remote control buttons, refer to page 27.

Adjusting Playback Level (DVD LEVEL)

The audio of a DVD VIDEO and DVD AUDIO may be recorded at a lower level (volume) than for other types of disc. You can adjust the DVD level.

■ While a disc is being played back

Press .

• Each time you press , the display toggles as follows in the display window.

: Sound level recorded in the

DVD.

: Enhances the sound level

(initial setting).

: Enhances the sound level to the

highest level.

• Select the level while listening to the sound played back.

NOTE

• DVD level is effective only for playback of a DVD.

• Even if the DVD level is changed, the output level from the digital audio output terminal will not be changed.

• This function does not affect recording sound.

Enjoying Better Pictures (PROGRESSIVE)

In the progressive mode, you can enjoy better pictures.

CAUTION

• In order to enjoy pictures in the progressive mode, the following requirements should be met.

• There must be component video input termi-

nals on the TV set connected to the main unit.

• The main unit and the TV set must be con-

nected using a component video cord

( page 15). When the above requirements are not satisfied, leave the main unit in the Interlace mode. If the progressive mode is set, pictures may be distorted.

■While the disc is played back or paused

Hold down .

• Each time you press , the display toggles as follows.

Interlace mode (initial setting)

English Listening to Discs English

Progressive mode

(Continued) Convenient Functions of the DVD Player

Introduction

Playing Back the Bonus Group

There are some DVD AUDIO discs with a special group, called "bonus group", recorded.

Bonus indicator

• This operation can be carried out when "BONUS" is lit in the display window on the main unit.

■ While a disc is being played back

1 Set the remote control mode

selector to AUDIO.

2 Press repeatedly during

playback to select a bonus group.

• "KEY_ _ _ _" appears on the TV screen and in the display window on the main unit.

3 Press the number buttons to enter

a pin code (4 digits).

• The method of getting a pin code is different depending on the disc.

4 Press .

• When a correct pin code is entered, "BONUS" disappears and the playback of the bonus group starts.

• If an incorrect pin code is entered, try entering a correct pin code again.

Browsable Still Pictures (B.S.P.)

There are some DVD AUDIO discs with still pictures recorded. Among the still pictures, there are pictures called B.S.P. (browsable still pictures). You can change these pictures as if turning over pages.

B.S.P. indicator

• This operation can be carried out when "B.S.P." is lit in the display window on the main unit.

■While a disc is being played back

1 Press .

• Each time you press , the still picture will be switched over.

• You can also change the pictures by pressing .

Example: TV screen

Selected page/ Total number of pages

Selected page (still picture)

2 Wait for a few seconds or press

NOTE

• You can operate this function on the menu bar ( page 35).

Playing Back the Disc in the Desired Order (Program Playback)

You can program a maximum of 99 chapters or tracks. You can program the same chapter or track more than once.

■ While a disc is stopped

1 Set the remote control mode

selector to AUDIO.

2 Press to select "PROGRAM".

■ Display for DVD VIDEO

For the locations of remote control buttons, refer to page 27.

Example: For DVD VIDEO

TV screen

Program screen

3 Press the number buttons ( -

or ) to program chapters/

tracks.

■Display for DVD VIDEO

• Select a title number, and then select a chapter number.

Title number Chapter number

Program number

English Listening to Discs English

Program indicator

■ Display for DVD AUDIO/MP3/WMA

DVD, MP3 or WMA

Program indicator

■ Display for CD/VCD/SVCD

Program indicator"VCD" is displayed while

VCD/SVCD is selected.

■Display for DVD AUDIO/MP3/WMA

• Select a group number, and then select a track number.

DVD, MP3 or WMA

Group number

Program number

Track number

■Display for CD/VCD/SVCD

• Select a track number.

Track numberCD or VCD

Program number Total time for

program playback

(Continued on next page)

(Continued) Convenient Functions of the DVD Player

Example: For DVD VIDEO

TV screen

• Refer to "Using the number buttons" ( page 17).

• Before selecting a bonus group of a DVD AUDIO, cancel the "BONUS" display as explained in "Playing back the Bonus Group" on page 31.

• When you try to enter more than 99 chapters or tracks, "MEMORY FULL" appears.

4 Press .

NOTE

• You can set tracks from either a disc or MD in a program playback setting.

Confirming programmed content

While playback is stopped, press

or repeatedly.

• During this operation, you can add a track as the last in the program, or erase

the last track. ( step 3)

Canceling program playback

While playback is stopped, press

repeatedly to display an item

other than "PROGRAM".

• This operation does not erase the programmed content.

Introduction

Random Playback

You can listen to tracks or chapters in random order.

■ While playback is stopped

1 Press repeatedly to select

"RANDOM".

Example: For CD

Random indicator

• "RANDOM" appears in the TV screen.

2 Press .

NOTE

• You can set tracks in random playback from either a disc or MD.

• Pressing repeatedly does not return playback to the previous track.

• Each track is played back once.

Canceling random playback

While playback is stopped, press

repeatedly to display an item

other than "RANDOM".

NOTE

• Ejecting the disc or turning off the main unit also cancels random playback.

Erasing the whole program

While playback is stopped, hold down

NOTE

• Ejecting the disc or turning off the main unit also erases the programmed content. This operation also cancels program playback.

For the locations of remote control buttons, refer to page 27.

Repeat Playback

Refer to page 38 for repeat playback of MP3/WMA and JPEG files.

■ While a disc is being played back

Press .

• Each time you press , the repeat type will be changed.

For DVD VIDEO

Repeat types

Repeats the

current chapter

Repeats the

current title

Cancels repeat

For DVD AUDIO

Repeat types

Repeats the

current track

Repeats the

current group

Cancels repeat

Display on the

TV screen

CHAP*

TITLE

OFF

Display on the

TV screen

TRACK*

GROUP

OFF

Display in the

display window

on the main unit

REPEAT CHAPTER*

REPEAT TITLE

REPEAT OFF

Display in the

display window

on the main unit

REPEAT TRACK*

REPEAT GROUP

REPEAT OFF

ALL

GROUP

English Listening to Discs English

For CD/VCD/SVCD

Repeat types

Repeats the

current track

Repeats all

tracks

Cancels repeat

Display on the

TV screen

TRACK*

ALL

OFF

Display in the

display window

on the main unit

REPEAT TRACK*

REPEAT ALL

REPEAT OFF

ALL

* "STEP" is displayed during program playback or

random playback.

NOTE

• For a VCD and SVCD, the operation can be carried out during playback without the PBC function

( page 24).

• You can also operate this function on the menu bar ( page 35).

• For details on A-B repeat (repeat playback of a designated part), refer to page 36.

Status Bar and Menu Bar

Time display selection

Remote control mode selector

Number buttons

Repeat mode

Time search

Chapter search/ Track search

You can display the status bar and menu bar on the TV screen, and can control discs with the bars.

CAUTION

• Set the remote control mode selector to AUDIO before using the number buttons.

Using the Status Bar and Menu Bar

■ While a disc is being played back

1 Press twice.

Status bar

Menu bar

• The above is an example for a DVD VIDEO.

2 Press to select an item you

want to operate.

3 Press .

• You can set the selected function. For the

setting items, refer to the following "Function list".

• The currently active function shows blue.

• To cancel the menu bar, press .

Function list

Audio

Subtitle

View angle

Page switch

Information displayed on the status bar

DVD VIDEO/DVD AUDIO (the example below is for a DVD VIDEO)

Transfer rate (only for DVD VIDEO)

(DVD VIDEO) Current title number (DVD AUDIO) Current group number

VCD/SVCD/CD (the example below is for a CD)

Introduction

Changes time information displayed in the display window on the main unit and

the status bar. Each time is

pressed, the display will be changed.

DVD VIDEO/DVD AUDIO

TOTAL : Elapsed playing time of current title/

group T.REM : Remaining time of current title/group TIME : Elapsed playing time of current

chapter/track REM : Remaining time of current chapter/track

CD/VCD/SVCD

TIME : Elapsed playing time of current track REM : Remaining time of current track TOTAL : Elapsed playing time of disc T.REM : Remaining time of disc

page 34

page 36

DVD VIDEO/DVD AUDIO

Selects a chapter/track. Press the number buttons to enter the chapter/

track number and press .

Examples:

5: 24:

DVD VIDEO/DVD AUDIO/VCD/SVCD

page 27

DVD VIDEO/DVD AUDIO/SVCD

page 28

DVD VIDEO/DVD AUDIO

page 28

Playback mode

NOTE

• The playback status mark has the same meaning of the mark on the on-screen guide ( page 24).

DVD AUDIO

Switches the still pictures (B.S.P.) recorded on a DVD AUDIO disc.

page 31

(DVD VIDEO) Current chapter number (DVD AUDIO) Current track number

Current track number

Time Playback status

Press to select, and press to determine unless otherwise noted.

Playing Back the Designated Part Repeatedly (A-B Repeat Playback)

■ While a disc is being played back

1 Press twice.

• The menu bar ( page 35) appears.

Designate the Time (Time Search)

■While a disc is being played back

1 Set the remote control mode

selector to AUDIO.

English Listening to Discs English

2 Press to select .

3 Press . 4 Press to select

OFF

A B

5 Press at the starting point of

the part to be repeated (designating A point).

• The icon on the menu bar will be .

6 Press at the end of the part to

be repeated (designating B point).

• The icon on the menu bar will be .

" A-B" appears in the display window on the main unit and the part between A and B points is played back repeatedly.

Canceling A-B repeat playback

• To cancel A-B repeat playback:

• Press .

• Select and press twice. (Select .)

NOTE

• You can operate a VCD and SVCD while the disc is played back with PBC off.

• A-B repeat playback is possible only within the same title or track. A-B repeat playback cannot be carried out during PBC playback, program playback, random playback and repeat playback.

2 Press twice.

• The menu bar appears ( page 35).

3 Press to select .

4 Press . 5 Enter the time using the number

buttons ( - , ).

Example: When you want to play back a

disc from the position of (0 hour) 23 minutes 45 seconds, press the buttons in the order:

• You can skip entering "minutes" and "seconds".

• If you enter wrong numbers, press to

delete the numbers, and then enter the numbers again.

6 Press .

• To delete the menu bar, press .

NOTE

• You may not be able to operate this function depending on the disc.

• This function does not work during program playback or random playback.

• For a CD, this operation can always be carried out. For a VCD or SVCD, the operation can be carried out when the disc is stopped or during playback without the PBC function.

• Time search for a DVD VIDEO is from the beginning of the title, for a DVD AUDIO is from the beginning of the track being played back. Time search for a VCD, SVCD and a CD is as follows:

• When the disc is stopped, time search is from

the beginning of the disc.

• When the disc is being played back, time search

is within the track currently being played back.

Introduction

Playing Back MP3/WMA and JPEG Discs

Playback

Display of an MP3/WMA disc is described here as an example.

Remote control mode selector

Number buttons

For a JPEG disc, read "track" as "file".

NOTE

• When playing back a disc containing both MP3/ WMA and JPEG files, set one of them to be played

( page 39).

1 Insert a disc.

Example: TV screen

This indicator lights up during program playback

(

page 32).

Group list

This indicator lights up during repeat playback

(

page 38).

Elapsed playing time of the selected track (only for MP3/WMA).

NOTE

• Set the remote control mode selector to AUDIO before using the number buttons.

Tag information of the selected track (only for MP3s/WMAs)

Example: Display window

Group number Track number

"WMA" is displayed when a WMA disc is loaded, and "JPG" is displayed when a JPEG disc is loaded.

Track list (Tracks contained in the selected group)

2 Press to select a group.

3 Press to move to the track list.

• Pressing returns to the group list.

4 Press to select a track.

5 Press or .

Example: Display during playback

Group number Track number

Elapsed playing time (This indicator is not displayed while a JPEG is loaded.)

• At first, a track title (file name) is scrolled.

• When an MP3 or WMA is loaded, tag information (title/artist/album) is scrolled followed by a track title.

• Only alphanumerical one-byte characters are displayed properly as a track title or tag information.

NOTE

• You can also use and in step 2.

•

You can also use t this case, steps 3 and 5 are not needed. Refer to

“Using the number buttons” ( page 17).

• You can also use or in step 4. In this case, step 3 is not needed.

Slide-show playback

he number buttons in step 4. In

Repeat Playback

■While a disc is being played back

Press .

• Each time you press , the repeat type is changed.

Repeat types

Repeats the current track (only for MP3/ WMA)

Repeats the current group

Repeats the entire disc

Cancels repeat playback

* "STEP" is displayed during program playback and

random playback.

NOTE

• The repeat types can also be changed while the disc is stopped.

• The repeat playback is automatically canceled if there is a file that cannot be played back

( page 4).

Display on the

TV screen

REPEAT TRACK*

REPEAT GROUP

REPEAT ALL

No display

Display in the

display window on

the main unit

REPEAT* TRACK

REPEAT GROUP

REPEAT ALL

REPEAT OFF

English Listening to Discs English

GROUP

ALL

• For a JPEG disc, when you press in step 5, files are continuously played back from the

selected file (slide-show playback). When you

press , only a selected file is played back.

• A file is displayed for approximately 3 seconds in a slide-show playback.

• After all files are played back, the playback is automatically stopped.

Preferences

)

Number buttons

You can change the initial settings of this product according to the environment the product is used in.

CAUTION

• Set the remote control mode selector to

AUDIO before using the number buttons.

NOTE

• The top and bottom of the preference screen may

not be displayed on a wide TV. Adjust the picture size on the TV.

Basic Operations

This section explains basic operation for changing various settings.

■ While a disc is stopped or no disc is loaded (while "NO DISC" is displayed)

1 Press .

• "SETTING" appears in the display window on the main unit and the following screen appears on the TV.

Introduction

LANGUAGE

NOTE

• If the selected language is not recorded on the disc, the optimum language set for the disc appears.

• For a language code such as "AA", refer to the "Language Codes" ( page 42).

Items Contents

MENU LANGUAGE

AUDIO LANGUAGE

SUBTITLE

ON SCREEN LANGUAGE

Select the language for the DVD VIDEO menu.

Select the audio language for the DVD VIDEO.

Select the subtitle language for the DVD VIDEO.

Select the language displayed on the preference screens.

PICTURE

Items Contents ( : initial setting)

MONITOR TYPE

Select a display method suitable for your TV. 16 : 9 /16 : 9 MULTI (wide TV):

Select this item when the aspect ratio of your wide TV is fixed to 16:9 (when playing back a DVD VIDEO recorded at 4:3, this product automatically adjusts the screen width of the output signal).

4 : 3 LB/4 : 3 MULTI LB (letter box

Select this item when the aspect ratio of your TV is conventional 4:3. While viewing a wide screen picture, the black bars appear on the top and bottom of the screen.

4 : 3 PS/4 : 3 MULTI PS (pan scan):

Select this item when the aspect ratio of your TV is conventional 4:3. While viewing a wide screen picture, the left and right edges of the picture will not be shown on the screen. (If the disc is not compatible with the pan scan, the picture will be displayed at the letter box ratio.)

• Proceed with operations by following the description on the TV screen.

PICTURE SOURCE

SCREEN SAVER

FILE TYPE

Select an item suitable to the video source.

VIDEO:

Select this item when you want to view a normal video.

FILM:

Select this item when you want to view a film or video recorded with the progressive scan method.

AUTO:

The video source type (a video or film) is automatically selected.

Select the screen saver mode between /OFF (screen saver activates when there is no operation made for about 5 minutes since a still picture was last displayed).

If a disc includes an file (MP3/WMA) and a still picture file (JPEG), select which file is played back. If you change this setting, open and close the disc tray, or momentarily turn off the main unit. (A disc either with audio files or still picture files can be played back regardless of this setting.)

AUDIO

OTHERS

English Listening to Discs English

Items Contents ( : initial setting)

DIGITAL AUDIO OUTPUT

DOWN MIX Switch signal from the digital output

D (Dynamic). RANGE COMPRESSION

Select an output signal type from the following in accordance with the equipment connected to the digital audio output terminal (AV amplifier, etc.). (See the list below for the preference items and output signal.)

PCM ONLY:

Equipment corresponding only to linear PCM.

DOLBY DIGITAL/PCM:

Dolby digital decoder or equipment having the same function.

STREAM/PCM

DTS/Dolby digital decoder or equipment having the same function.

terminal of the DVD VIDEO according to the connected equipment. Select this when Digital Audio Output is set to "PCM ONLY".

DOLBY SURROUND

A dolby pro logic decoder-built-in equipment.

STEREO:

An ordinary equipment.

• When 3D phonic is activated, Down Mix does not work.

To make adjustments for the difference between a high volume and a low volume when playing back with low volume (only for a DVD recorded with Dolby digital).

AUTO

D. range compression automatically works.

ON:

D. range compression always works.

Items Contents ( : initial setting)

RESUME ( page 25)

ON SCREEN GUIDE

AV COMPU LINK MODE

PARENTAL LOCK

Select whether you display guide icons on the on-screen guide indicating status of a disc/main unit (For details on the guide icons, refer to page 24)

When you want to control JVC TV by using this product, select a mode that matches the terminal from the following. (For more details, refer to "Using AV COMPU LINK" on page 73.)

DVD1

Connect to the video-3 input on the TV set.

DVD2:

Connect to the video-1 input of the TV set.

DVD3:

Connect to the video-2 input of the TV set.

Set the parental lock function to cut off violent scenes or replace the scenes with others. (This is effective only for discs equipped with the parental lock function.)

COUNTRY CODE ( page 41)

Select your country or area.

SET LEVEL:

The restriction is stricter as the number becomes smaller. "NONE" is no restriction.

PASSWORD (essential):

Enter four-digit number as your password using the number buttons (1-9, 0) every time. (Enter "8888" if you forget your password.) The password is required at the time of playback.

• If you enter a wrong password three times, "EXIT" will be automatically selected.

List of relationships of DIGITAL AUDIO OUTPUT preference items and output signal

Playback disc

48 kHz, 16/20/24 bits

Linear PCM DVD VIDEO

96 kHz linear PCM DVD VIDEO

16/20/24 bits linear PCM DVD AUDIO

48/96/192 kHz,

44.1/88.2/176.4 kHz,

DTS DVD VIDEO DTS bit stream 48 kHz, 16 bits stereo linear PCM

DOLBY DIGITAL DVD VIDEO/

DVD AUDIO

CD/VCD/SVCD 44.1 kHz, 16 bits stereo linear PCM/48 kHz, 16 bits linear PCM

DTS CD DTS bit stream 44.1 kHz, 16 bits linear PCM

MP3/WMA disc 32/44.1/48 kHz, 16 bits linear PCM

NOTE

STREAM/PCM DOLBY DIGITAL/PCM PCM ONLY

DOLBY DIGITAL bit stream

• For a DVD VIDEO without content protection set, there is a 20 bit or 24 bit output at the digital audio output terminal.

DIGITAL AUDIO OUTPUT preference

48 kHz, 16 bits stereo linear PCM

44.1 kHz, 16 bits stereo linear PCM

48 kHz, 16 bits stereo linear

PCM

Country/Area Codes

Introduction

Language Codes

Code Language Code Language AA Afar MK Macedonian

AB Abkhazian ML Malayalam AF Afrikaans MN Mongolian AM Ameharic MO Moldavian AR Arabic MR Marathi AS Assamese MS Malay (MAY) AY Aymara MT Maltese AZ Azerbaijani MY Burmese BA Bashkir NA Nauru BE Byelorussian NE Nepali BG Bulgarian NL Dutch BH Bihari NO Norwegian BI Bislama OC Occitan BN Bengali, Bangla OM (Afan) Oromo BO Tibetan OR Oriya BR Breton PA Panjabi CA Catalan PL Polish CO Corsican PS Pashto, Pushto CS Czech PT Portuguese CY Welsh QU Quechua DA Danish RM Rhaeto-Romance DZ Bhutani RN Kirundi EL Greek RO Rumanian EO Esperanto RU Russian ET Estonian RW Kinyarwanda EU Basque SA Sanskrit FA Persian SD Sindhi FI Finnish SG Sangho FJ Fiji SH Serbo-Croatian FO Faroese SI Singhalese FY Frisian SK Slovak GA Irish SL Slovenian GD Scots Gaelic SM Samoan GL Galician SN Shona GN Guarani SO Somali GU Gujarati SQ Albanian HA Hausa SR Serbian HI Hindi SS Siswati HR Croatian ST Sesotho HU Hungarian SU Sundanese HY Armenian SV Swedish IA Interlingua SW Swahili IE Interlingue TA Tamil IK Inupiak TE Telugu IN Indonesian TG Tajik IS Icelandic TH Thai IW Hebrew TI Tigrinya JI Yiddish TK Turkmen JW Javanese TL Tagalog KA Georgian TN Setswana KK Kazakh TO Tonga KL Greenlandic TR Turkish KM Cambodian TS Tsonga KN Kannada TT Tatar KO Korean (KOR) TW Twi KS Kashmiri UK Ukrainian KU Kurdish UR Urdu KY Kirghiz UZ Uzbek LA Latin VI Vietnamese LN Lingala VO Volapuk LO Laothian WO Wolof LT Lithuanian XH Xhosa LV Latvian, Lettish YO Yoruba MG Malagasy ZU Zulu MI Maori

English Listening to Discs English

Listening to Cassette Tapes

1 Insert a cassette tape.

Cassette tape indicator (The cassette tape indicator lights up while the cassette tape is stopped. The cassette tape indicator flashes while the cassette tape is being played back.)

Cassette tape playback direction ( : normal direction/ : opposite direction)

Introduction

Insert a cassette tape with the side you want to listen to facing up.

Reverse mode

Stop

Fast forward/ Rewind

Operation

Press .

Press or .

• When a cassette tape is played back

in the normal direction ( ), is

fast forward and is rewind.

• When the cassette tape is played back in the opposite direction ( ),

is fast forward and is

rewind.

• You can perform the same operation

by pressing or .

CAUTION

• Before using a cassette tape, wind up any slack in the cassette tape. ( page 75)

• Do not use long cassette tapes such as C-120 or C-150. Long cassette tapes are thin and stretch easily, and may become tangled in the inner part of the main unit.

• This product is compatible with playback of TYPE I cassette tapes. Playback of TYPE II or TYPE IV cassette tapes is not recommended, because this product does not meet the specifications for these tapes. The main unit does not produce the proper sound from these cassette tape types.

2 Press repeatedly to select

the reverse mode.

: For one return playback of both

sides.

: For repeated playback of both sides

(Playback continues until playback is stopped.)

: For one-way playback of either side.

Listening to Cassette Tapes

3 Press .

• Playback starts.

• When the main unit is turned off, pressing

automatically turns on the main unit.

• Each time you press , the cassette tape

playback direction changes. The initial playback direction after you have inserted a cassette tape is always the normal direction.

• The cassette tape playback direction indicator facing right is displayed during normal playback. The indicator facing left is displayed during reverse playback.

Changing the Display in the Display Window

Press .

• Each time you press , the display toggles as follows.

Sound source name

(With an MD loaded)

(Time display)

Display of remaining time for MD recording

English Listening to Cassette Tapes English

Clock display

Listening to Cassette Tapes/Listening to Other Equipment

Listening to Other Equipment

2 (With "AUX" being displayed) Hold

down until the input level appears.

• Each time you hold down , the display toggles as follows.

Adjusting the sound input level of the AUX-DIGITAL

1 Press repeatedly to select

"AUX-DIGITAL".

2 (With "AUX-DIGITAL" being

displayed) Hold down until the input level appears.

3 Press or to adjust the

input level.

1 Press .

• Each time you press , the display toggles as follows.

AUX : To listen to sound from other

equipment connected to the AUX terminals on the main unit.

AUX-DIGITAL : To listen to sound from other

equipment connected to the OPTICAL DIGITAL IN terminal on the main unit.

2 Start other equipment playback.

• Refer to the operation manual for the connected equipment.

3 Adjust the volume and make other

necessary settings.

• For adjusting the volume and making other necessary settings, refer to "Basic Opera-

tions" ( page 18).

• You can adjust the input level within the range of -12 dB to 12 dB (in increments of 2 dB). The initial setting is 0 dB.

4 Press .

Changing the Display in the Display Window

Press .

• Each time you press , the display toggles as follows.

Sound source name

(Time display)

Clock display

Introduction

For ordinary use. (initial setting)

For increasing the level.

(With an MD loaded) Display of remaining time for MD recording

Adjusting the Sound Input Level from Other Equipment

Adjusting the sound input level of the AUX

1 Press repeatedly to select

"AUX".

Listening to Other Equipment/Listenin g to MDs

Listening to MDs

Remote control mode selector

Listening to MDs

■When the main unit is turned on

1 Insert an MD.

English Listening to Other Equipment/Listening to MDs English

NOTE

• Set the remote control mode selector to AUDIO before using the number buttons.

Operation

Stop

Pause

Skip

Fast forward/ Rewind (Search)

Eject

Press .

Press during playback. Pressing

again resumes playback.

Press the button repeatedly.

Hold down the button during playback.

Press the button during

playback. (Pressing

during search resumes normal playback.)

Press on the main unit.

Number buttons

CAUTION

• Do not insert an MD while the main unit is turned off. Forcibly inserting an MD may damage the main unit.

2 Press .

■Display while an MD is being played back

MD indicator (The MD indicator lights up while the MD is stopped. The MD indicator flashes while the MD is being played back or paused.)

Group number*

Track number

MDLP mode ( page 51)

• When the track title has been set to the

track, the track title appears first.

* When the track being played back does not

belong to a group, "G - -" appears.

CAUTION

• Do not insert another MD while the MD indicator is lighting up or flashing. Forcibly inserting an MD may damage the main unit.

■Display while the MD is stopped

Total number of tracks

Elapsed playing time

Total number of groups*

Total playing time

• When the MD title (the disc title) has been

set to the MD, the MD title appears first.

• Long titles are scrolled. * When no group belongs to the MD, "G - -"

appears.

(Continued) Listening to MDs

Introduction

Changing the Display in the Display Window

Press .

• Each time you press , the display toggles as follows.

■ While an MD is being played back

Display while an MD is being played back

( page 46)

Track title display

Group title display

Clock display

■ While an MD is stopped

Display while an MD is stopped ( page 46)

When no title has been set to a track, "NO TR TITLE" appears.

When the track being played back does not belong to a group, no group title display appears. When no title has been set to a group, "NO GR TITLE" appears.

Group Playback of an MD

You can play back just the tracks from a group which you want to listen to.

■While an MD is stopped

1 Press repeatedly to select

"GROUP".

Group indicator

2 Press .

• Group 1 playback starts.

• If there is no group, "GROUP" disappears and normal playback starts.

3 Press or to select a

group.

• When playback of all tracks in the selected group finishes, playback automatically stops.

Canceling group playback

Disc title display

Clock display

NOTE

• While an MD is selected as the sound source, when you insert an MD to which nothing has been recorded, "BLANK DISC" appears.

When no title has been set to an MD, "NO TITLE" appears.

Specifying the Track (Direct Track Selection)

1 Set the remote control mode

selector to AUDIO.

2 Press the number buttons ( -

or ) to select the track you

want to listen to.

• Refer to "Using the number buttons" (

page 17).

While playback is stopped, press

repeatedly to select an item

other than "GROUP".

NOTE

• Ejecting the MD or turning off the main unit also cancels group playback.

Listening to MDs

For the locations of remote control buttons, refer to page 46.

Program Playback

This function allows you to program up to 32 tracks.

■ While the MD is stopped

1 Set the remote control mode

selector to AUDIO.

2 Press to select "PROGRAM".

Example: Display while MD program playback

is selected

Program indicator

3 Press the number buttons ( -

or ) to select the track num-

bers.

• Refer to "Using the number buttons" ( page 17).

Track number Program number

Confirming the programmed track order

While playback is stopped, press

or repeatedly.

• You can add a track as the last track in the program, or erase the last track.

( step 3)

Canceling the program playback

While playback is stopped, press

repeatedly to display an item

other than "PROGRAM".

• This operation does not erase the program.

Erasing all the programmed tracks

While playback is stopped, hold down

NOTE

• Ejecting the MD or turning off the main unit also erases all the programmed tracks. This operation also cancels program playback.

Random Playback

English Listening to MDs English

Total time for program playback

NOTE

• When you want to erase the program, press while playback is stopped. Programmed tracks are

erased one by one from the last track. Holding

down erases all programmed tracks.

• When you try to program the 33rd track, "MEMORY FULL" appears in the display window to indicate that 33 or more tracks cannot be programmed.

• When total time for program playback reaches 2 hours 31 minutes for an MD, "--:--" appears.

4 Press .

NOTE

• You can set tracks for program playback either from a CD, MD or DVD.

This function allows you to listen to tracks in random order.

■While a disc is stopped

1 Press repeatedly to select

"RANDOM".

Example: Display while MD random playback is

selected

Random indicator

2 Press .

NOTE

• You can set tracks for random playback either from a CD, MD or DVD.

• Pressing repeatedly does not return playback to the previous track.

• Each track is played back once.

(Continued) Listening to MDs

Introduction

Canceling the random playback

While playback is stopped, press

repeatedly to display an item

other than "RANDOM".

NOTE

• Ejecting the MD or turning off the main unit also cancels random playback.

Repeat Playback

This function allows you to repeatedly listen to the same track.

During MD playback, press repeatedly to select the repeat mode.

• Each time you press , the display toggles as follows.

Example: While "REPEAT ALL" is selected

Searching Titles

This function allows you to search titles for tracks or groups in an MD.

■While a disc is stopped

1 Set the remote control mode

selector to AUDIO.

2 Press repeatedly to select the

search type.

For searching track titles.

For searching group titles. (This function is available only when there are groups.)

3 Press .

Example:Display while track titles are being

searched

Repeat indicator

: For repeating all tracks in an

MD. For repeating all tracks in the selected group when MD group playback is selected.

: For repeating one track.

: For canceling repeat playback.

NOTE

• Ejecting the MD or turning off the main unit also cancels repeat playback.

While group titles are being searched, "GROUP SEARCH" is displayed.

4 Enter the title you want to search.

• Enter the first one to five characters of the title. Example: Entering "F" searches titles

starting with "F" in order of track number. Entering "Frien" searches titles starting with "Frien" in order of track number.

• For entering titles, refer to "Entering Titles" ( page 59).

• When searching tracks or groups with no titles, enter nothing, and then proceed to step 5.

5 Press .

• "SEARCH" appears and the title search starts. When the title is found, playback of the track starts. When playback finishes, the next title search automatically starts.

NOTE

• A space is treated as a character. However, when no character exists after the space, the space is ignored.

• Capital letters and small letters are distinguished.

• When no corresponding titles are found, "SEARCH END" appears.

For the locations of remote control buttons, refer to page 46.

Searching another track or group title

Press (or ).

Quitting the title search

Press .

• The title search is canceled and playback returns to the beginning of the current track.

English Listening to MDs English

Recording Sound

Recording Sound to MDs

Introduction

Main unit

Remote control

3 Press to select the MDLP

mode.

• Each time you press , the display toggles as follows.

: For standard stereo recording

(Maximum recording time is 80 minutes with an MD 80).

:For

2 extended stereo recording (Maximum recording time is 160 minutes with an MD 80).

:For

4 extended stereo recording (Maximum recording time is 320 minutes with an MD 80).

• As you change the MDLP mode (SP→LP2→LP4), the sound quality also changes. When you want to record sound at the best possible quality, select the SP mode.

• When you use an MD car audio system, portable MD player or other MD player that is not compatible with the MDLP mode, select the SP mode.

4 Press to set group recording.

• Each time you press , the display toggles as follows.

: Activates group record-

ing (initial setting).

Recording All Tracks from a Disc to an MD

1 Press , and then press .

• The DVD is selected as the sound source and playback is stopped.

■ When recording sound from DVD VIDEOs

• Play back a title or chapter, pause playback,

and then press to return to the beginning of the first title/chapter.

• You may not be able to record a DVD VIDEO depending on the disc.

2 Insert an MD.

• Close the write protect knob on the MD beforehand ( page 75).

: Cancels group recording.

• You can form or cancel a group after the recording finishes. ( pages 63 and 66)

5 Press to select the recording

speed.

• Each time you press , the display toggles as follows.

: ×5 high speed recording

(only for CDs)

: Normal speed recording

• Select "NORMAL REC" when you want to play back a disc other than a CD.

• Recorded sound quality is the same for both "HIGH SPEED" and "NORMAL REC".

• You cannot listen to the sound during ×5 high speed recording.

6 Press on the main unit.

Example: Display while CD is recorded

Elapsed playing time of the track being recorded

Remaining time for recording

• When recording finishes, the color pattern of the display window and disc tray changes to the color pattern set in "MANUAL" to inform

you that recording has finished ( page

19).

• When "HCMS CANNOT COPY" appears, refer to pages 74 and 76.

NOTE

• The recorded sound level is automatically adjusted.

• The CD rotates at high speed during x5 high speed recording. Therefore, depending on the condition of the CD, the sound may be recorded improperly and affected by noise. If the sound is not recorded properly, select normal speed recording.

• The remaining time for recording differs depending on the selected MDLP mode.

• You cannot record sound while the repeat playback function is on. Starting the recording function automatically cancels repeat playback.

• While recording a DVD video, you cannot make settings on the DVD including audio, subtitle, view angles, picture magnification and 3D PHONIC selection.

This indicator lights up during

× high speed recording.

MDLP mode

This indicator lights up during group recording.

Recording the Second or Subsequent Track to the Last Track from a Disc

■When recording CDs/VCDs/SVCDs/DVD VIDEOs (For a DVD VIDEO: while the disc is paused)

Before proceeding to step 6, select the starting track or chapter number by

pressing or .

■When recording DVD AUDIOs/MP3s/ WMAs

Before proceeding to step 6, select the

group number by pressing

, and then select the track

number by pressing or .

Program Recording from a Disc

Before performing step 1 on page 51, program the tracks you want to record ( page 48).

•

Select normal speed recording ( step 5 on page 51). When you select "HIGH SPEED" and proceed to step 6, "CANNOT REC × 1 REC ONLY" appears in the display window and recording does not start.

English Recording Sound English

Quitting Recording

Press .

Recording Only One Track from a Disc

(Excluding DVD VIDEOs)

Before proceeding to step 6, start playback of the track you want to record.

• Pressing in step 6 returns playback to the beginning of the track, and only that track is recorded.

• This one-track recording is not available for DVD VIDEOs.

Recording Sound

)

(Continued) Recording Sound to MDs

Introduction

Changing the display in the display window during recording

Press .

• Each time you press , the display toggles as follows.

Recording disc track number

Recording MD track number

Clock display

Elapsed playing time of the chapter or track being recorded

Remaining MD recording time

Recording MD group number (When tracks have not been recorded in a group, "G - -" appears.

Things You Should Know about MD Recording

• It may be unlawful to record or playback copyright material without the consent of the copyright owner.

• You can record tracks having different MDLP modes onto an MD.

• You cannot use the monaural extended recording function with this product.

CAUTION

• Do not bump or sway the main unit during MD recording. Be especially careful while "WRITING" is displayed. Such movement may interfere with MD playback.

• You cannot play back tracks recorded in LP2 or LP4 with audio equipment that is not compatible with MDLP. When you attempt playback, "LP: " appears in front of the track title, and the main unit does not produce any sound. When you play back tracks recorded in LP2 or LP4 with audio equipment that is compatible with MDLP, "LP: " does not appear.

To activate or cancel the "LP: " indicator, press .

( on the right)

"LP: " indicator setting

Press .

• Each time you press , the display toggles as follows.

: For adding "LP: " to the track title.

: For deleting "LP: " from the track

title.

CD-R/CD-RW/DVD AUDIO recording

• When you record sound from a CD-R, CD-RW

or DVD AUDIO onto an MD, pressing may display "SCMS CANNOT COPY" in the display window, and digital recording may not be available. In such a case, set the recording speed to nor-

mal, hold down for 4 or more seconds. While ”ANALOG REC?” is displayed, press

once again to select analog recording.

• You can record up to 254 tracks to an MD. If you try to record 255 or more tracks, "DISC FULL" appears.

• When you use a partially-recorded MD, this product searches for the blank portion and records the new tracks to that portion. Unlike cassette tape recording, you cannot record over old tracks on an MD.

• Changing in sound volume and quality on this product during recording does not affect the recorded sound.

• Sound from a CD is recorded as digital signals to an MD. Sound from the radio or AUX is converted from analog signals to digital signals during recording.

• When you record a disc, track marks are automatically inserted between tracks. However, track marks may not be inserted when a DVD VIDEO or DVD AUDIO is recorded.

Recording Sound from Radio, Cassette Tape or Other Equipment

NOTE

• The recorded sound level is automatically adjusted.

• Sound-synchronized recording is employed for recording sound from other equipment (AUX). With sound-synchronized recording, this product automatically identifies sound signals from the sound source and starts recording. When sound from the sound source pauses for 30 or more seconds, this product automatically quits recording. The blank time between the last recorded track and the next recorded track is approximately 2 seconds.

For the locations of remote control buttons, refer to page 51.

1 Select a sound source.

Sound source Operation

Radio broadcast

Cassette tape playback

Sound from other equipment (AUX/ AUX-DIGITAL)

Select the radio station whose broadcast you want to record ( page

20).

Insert a cassette tape for playback,

press , and then press .

Press to select the reverse mode when necessary.

Press repeatedly to select AUX or AUX-DIGITAL, and prepare play-

back on the other equipment ( page 45).

2 Insert an MD for recording.

• Confirm the MDLP, "LP: " indicator and group recording settings. ( pages 51

and 53)

• Close the write protect knob on the MD ( page 75).

3 Hold down on the main unit for

approximately 4 seconds to display the track mark options.

4 While the track mark options are

displayed, press to select a track mark option.

• Each time you press , the display toggles as follows.

: Each time you press during

recording, a track mark is set (initial setting).

• When recording the sound from other equipment, wait until "AUX → MD" appears, and then start playback of the connected equipment. Recording automatically starts when sound is input to the main unit. You can also start recording by pressing

With this method, even when sound from the connected equipment pauses for 30 or more seconds, the main unit does not automatically quit recording.

Quitting Recording

Press .

Changing the display in the display window during recording

Press .

• Each time you press , the display toggles as follows.

Recording sound source name

Remaining time for recording

Recording sound source name

English Recording Sound English

: Track marks are automatically set

in 5-minute intervals.

: When no sound is produced for 3

or more seconds, a track mark is automatically set. You can also insert a track mark by pressing

5 Press on the main unit.

Example: Display while FM radio broadcast is

recorded

Recording MD track number

Clock display

Recording MD group number (When tracks are not recorded in a group, " - -" appears.)

Recording Sound to Cassette Tapes

Introduction

Main unit

Remote control

Preventing recorded sound from being erased

• Write protect tags are attached to a cassette tape for preventing the erasing of recorded sound. They enable you to avoid losing important recordings because once you snap off the write protect tags, you cannot record to the cassette tape or erase recorded material.

• When you want to use the cassette tape for recording again, cover the tag holes with adhesive tape.

Write protect tag for side B

Write protect tag for side A

1 Insert a cassette tape for record-

ing.

• Before inserting the cassette tape, wind the tape past the leader part of the cassette tape.

NOTE

• The sound input level during recording is automatically adjusted.

• When you record tracks from a disc or MD, a 4second blank is inserted between tracks in the recording. You can record tracks with no blank

time. ( page 56)

CAUTION

• It may be unlawful to record or playback copyright material without the consent of the copyright owner.

• Do not use long cassette tapes such as C-120 or C-150. Long cassette tapes are thin and stretch easily, and may become tangled in the inner part of the main unit.

• Since this product is not compatible with TYPE II and TYPE IV cassette tapes, do not use these types of cassette tapes. This product does not meet the specifications for these tapes, so sound is not properly recorded to these types of cassette tapes. You cannot obtain proper playback sound.

Magnetic tape (recordable part)

Leader tape (unrecordable part)

2 Press to select the reverse

mode.

• Each time you press , the display toggles as follows.

: For one-way recording on either

side.

: For one return recording on both

sides.

: Pressing automatically

starts one return recording on

• You can change the reverse mode during recording.

both sides.

Select a sound source for recording.

• Before selecting a sound source, make sure to stop a disc and MD.

Sound source Operation

Recording the Second or Subsequent Track to the Last Track from a Disc or MD

English Recording Sound English

Disc

Radio broadcast

Sound from other equipment (AUX/ AUX-DIGTAL)

Press , and then press .

Select the radio station whose broadcast you want to record ( page 20).

Press repeatedly to select AUX or AUX-DIGITAL, and prepare playback

on the other equipment ( page 45).

4 Press on the main unit.

Example: Display while CD sound is recorded

• When you record from a disc or MD, all tracks are recorded to the cassette tape.

• When you want to record sound from other equipment, start playback on the connected equipment.

• When recording finishes, the color pattern of the display window and disc tray switches to the color pattern set in "MANUAL" to inform

you that recording has finished (

19).

Quitting Recording

Press .

Recording Only One Track from a Disc or MD

(Excluding DVD VIDEOs)

Before proceeding to step 4, play back the track you want to record.

• Pressing in step 4 returns playback to the beginning of the track and only that track

is recorded.

page

(For a DVD VIDEO: while the disc is paused)

■For a CD/VCD/SVCD/DVD VIDEO

Before proceeding to step 4, select the starting track/chapter number by

pressing or .

■For a DVD AUDIO/MP3/WMA

Before proceeding to step 4, select the

group number by pressing or

, and then select the track num-

ber by pressing or .

Program Recording from a Disc or MD

Before proceeding to step 4, program the tracks you want to record ( pages 32 and 48).

Recording with No Blank Time between Tracks

Before proceeding to step 4, play back a disc or MD, pause the playback, and

then press to return to the beginning of the first track.

Erasing Recorded Sound from a Cassette Tape

Select the sound from other equipment (AUX) in step 3, and then press

• Do not play back any tracks on the connected equipment.

(Continued) Recording Sound to Cassette Tapes

Changing the display in the display window during recording

Press .

• Each time you press , the display toggles as follows.

■While tracks from a disc or MD are being recorded

DVD, CD or MD

Elapsed playing time

■While a radio broadcast (FM/AM) is being recorded

FM or AM

Introduction

For the locations of remote control buttons, refer to page 55.

Frequency

■While sound from other equipment (AUX) is being recorded

Clock display

NOTE

• If the cassette tape reverses direction while a track is being recorded from a disc or MD, this product starts recording that track again from the beginning onto the reverse side of the cassette tape. However, if 12 or less seconds of that track were recorded onto the first side of the cassette tape, recording to the reverse side of the cassette tape starts from the beginning of the previous track.

• Before recording a long track from an MD, such as a recorded concert, using one return recording, use the divide function to divide the track into sections equal to the length of one side of the cassette tape. ( page 32)

Recording Sound/Editing MDs

Giving (Editing) Titles

Things You Should Know about Editing

• You cannot edit an MD while its write protect knob is open ( page 75). When you attempt

to edit a protected MD, "DISC PROTECTED" appears.

• When you finish editing, "EDITING" appears, then "WRITING" flashes and the edited setting is recorded to the MD. While "WRITING" is displayed, be careful not to bump or sway the main unit. Such movement may interfere with MD playback.

• You cannot edit an MD during program playback, random playback, or group playback.

Remote control mode selector

For editing an MD (disc) title or track titles

• Press to display the title editing mode.

• To edit a disc title, press repeatedly to display "DISC TITLE?". You can also dis-

play "DISC TITLE?" by pressing while the disc is stopped.

• You can also select track number with

or .

For editing group titles

• Press twice to display the group title editing mode.

English Recording Sound/Editing MDs English

Number buttons

NOTE

• Set the remote control mode selector to AUDIO before using the number buttons.

Giving (Editing) Titles

You can give titles to an MD (disc), tracks and groups.

■ While the track or group to which you want to give a title is being played back

1 Set the remote control mode

selector to AUDIO.

• You can also select a group number with

or .

3 Press .

Character entry position (flashing)

A track number appears for entering a track title, or "GR" and a group number appear for entering a group title.

Available character types:

[ ] indicates the selected character type. [A]:Uppercase characters or symbols [a]:Lowercase characters or symbols [1]:Numerical characters

4 Enter a title using the number

buttons.

• For entering a title, refer to "Entering Titles" ( page 59).

5 Press .

• The entered title is given to an MD, track or group.

To quit title editing To give next title

Press .

2 Display the title editing mode.

Go to step 4.

(Continued on next page)

(Continued) Giving (Editing) Titles

Introduction

For the locations of remote control buttons, refer to page 58.

6 Press on the main unit to eject

the MD.

NOTE

• Number of characters that can be entered to an MD You can enter up to 1 792 characters to each MD, with up to 61 characters to each track. However, the actual number of characters that you can enter is less than the number indicated here because of restrictions of the MD writing method. Spaces are counted as characters. When you use long-play stereo recording (LP2 or LP4), the larger the number of tracks is, the smaller the number of characters that you can enter, because "LP: " and 4 spaces are automatically added to each track. You can set this product so that "LP: " is not

added to tracks. ( page 53)

Example: When editing 120 tracks recorded

using long-play stereo recording to an MD, you can enter 10 characters to each track.

• You cannot edit a title consisting of 62 or more characters. When you want to edit a title containing 62 or more characters, edit the title on the equipment on which the title was entered.

• You can set a title during recording.

• While recording from a CD (except when

recording only one track from a CD), you can enter up to 16 track titles before recording finishes.

• If you do not press before recording

finishes, the entered titles are not stored.

• During group recording, you can enter titles for

the group.

Entering Titles

Example: To enter "F"

1) Press repeatedly until [ ] appears on

"A".

2) Press repeatedly to display "F".

Character entry position (flashing)

To move the character entry position

• Press or .

• When you want to enter "NO", "TV" or two characters which are assigned to one button, enter

the first character, press to move the charac-

ter entry position to the right, and then enter the second character.

To erase a character

• Move the character entry position to the charac-

ter you want to erase, and press .

To enter a space

• Select the space from "Symbol" ( the chart below). You can also enter a space at the end of

a title by pressing .

To quit title entry

• Press or . The entered titles are not stored.

Available Characters

Button



Uppercase

character

Symbol*

ABC

DEF

GHI

JKL

MNO

PQRS

TUV

WXYZ

Lowercase

character

Symbol*

abc

def

ghi

jkl

mno

pqrs

tuv

wxyz

Numerical

character

Available character types:

[ ] indicates the selected character type. [A]:Uppercase characters or symbols [a]:Lowercase characters or symbols [1]:Numerical characters

• Several characters are assigned to one button. Press the button repeatedly until the desired character is displayed.

• For the available characters, refer to "Available Characters" ( on the right).

*Available symbols

Spac e

Editing Tracks

Editing MDs

For the locations of remote control buttons, refer to page 58.

Dividing a Track into Two Tracks (DIVIDE)

Example: Dividing a tune into tune A and tune B

Track number

■ While the track you want to divide is being played back

1 Press repeatedly to select

"DIVIDE?".

2 Press .

• You can also select the track number with

, or the number buttons. Refer to

"Using the number buttons" ( page 17).

4 Press or .

• You can adjust the dividing point within the range of -128 to +128 position (approximately -8 to +8 seconds in SP mode).

5 Press .

6 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

• You cannot divide a track in an MD containing

254 or more tracks. When you press in step 3, "DISC FULL" appears.

•

When you divide a track that has a title, the title is added to both divided tracks.

English Editing MDs English

3 Press to specify the dividing

point.

• This product repeatedly plays back the 4 seconds of sound immediately following the dividing point.

"POSIT." stands for "POSITION".

• When the dividing point does not have to be adjusted, proceed to step 5.

• When you want to adjust the dividing point, proceed to step 4.

(Continued) Editing Tracks

Introduction

Joining Tracks (JOIN)

You can join two adjacent tracks into one track.

Example: Joining tune A and tune B

■ While the second track (track 2 in the example shown above) to which you want to join the first track is being played back

1 Press repeatedly to select

"JOIN?".

2 Press .

Track number

Moving a Track (MOVE)

Example: Moving tune B

■While the track you want to move (track 2 in the example shown above) is being played back

1 Press repeatedly to select

"MOVE?".

2 Press .

• You can also select a track number with

, or the number buttons. Refer to

"Using the number buttons" ( page 17).

3 Press . 4 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

• You cannot join tracks that have different MDLP modes (SP/LP2/LP4), or tracks that have different recording types (digital/analog). If you attempt to join such tracks, "CANNOT JOIN" appears.

• When you join two tracks that have titles, the title of the first track remains as the title of the joined track.

• You can also select a track number with

, or the number buttons. Refer to

"Using the number buttons" ( page 17).

3 Press . 4 Press or to select the

track number to which you want to move the specified track.

(Track 5 is selected in the example shown above)

• You can also select a track number with the number buttons. Refer to "Using the number

buttons" ( page 17).

• When you move a track to a track number which is registered in a group, the track is registered in the group. When you move a track which is registered in a group to a track number which is not registered in a group, the track is removed from the group registration.

5 Press . 6 Press .

For the locations of remote control buttons, refer to page 58.

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

Erasing a Track (ERASE)

Example: Erasing tune B

CAUTION

• Once you erase a track, you cannot retrieve it. Before erasing a track, confirm that you no longer need it.

■ While the track you want to erase (track 2 in the example shown above) is being played back

4 Press . 5 Confirm that you no longer need

the tracks, and then press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

Erasing All Tracks (ALL ERASE)

All tracks are erased.

CAUTION

• Once you erase a track, you cannot retrieve it. Before erasing a track, confirm that you no longer need it.

English Editing MDs English

1 Press repeatedly to select

"ERASE?".

2 Press .

• You can also select a track number with

, or the number buttons. Refer to

"Using the number buttons" ( page 17).

3 Press .

• " " is added in front of the selected track number.

• When you select a wrong track, press to delete “ “.

• You can select up to 15 tracks to be erased

with , or the number buttons, and

. Refer to "Using the number buttons"

( page 17).

1 Press repeatedly to select

"ALL ERASE?".

2 Press . 3 Confirm that you no longer need

all tracks, and then press .

NOTE

• You can quit the editing operation by pressing .

Editing Tracks by Group

Introduction

You can sort tracks into 99 groups maximum.

Forming a Group (FORM GR)

You can group tracks together. A sequence of tracks that is not registered in any group can be grouped.

Example: Forming tune A, tune B and tune C

into a group

Group 1

■ While the track which you want to specify as the first in the group (track 1 in the example shown above) is being played back

1 Press repeatedly to select

"FORM GR?".

• "GR" stands for "GROUP".

2 Press .

The first track number in the group

3 Press . 4 Press or to select the

track number which you want to specify as the last in the group.

(Track number 3 is selected in the example shown on the left.)

The last track number in the group

• You can also select a track number with the number buttons. Refer to "Using the number

buttons" ( page 17).

5 Press . 6 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

• If you select a track in another group, "GROUP TRACK" appears and you cannot proceed to the next step.

• If you select a sequence including a track that is registered in another group, "CANNOT FORM!" appears and you cannot proceed to the next step.

"T" stands for "TRACK".

• You can also select a track number with

, or the number buttons. Refer to

"Using the number buttons" ( page 17).

The first track

Group 1

The last track

For the locations of remote control buttons, refer to page 58.

Adding a Track to a Group (ENTRY GR)

You can add a track to the specified group as the last track of the group.

Example: Adding tune F to group 1

Group 1 Group 2

■ While the track which you want to add to a group (track 6 in the example shown above) is being playeds back

1 Press repeatedly to select

"ENTRY GR?".

2 Press .

Track number

Dividing a Group into Two Groups (DIVIDE GR)

Example: Dividing group 1 into two groups

Group 1

Group 1 Group 2

■While the track which you want to specify as the first in the second group (track 4 in the example shown above) is being played back

1 Press repeatedly to select

"DIVIDE GR?".

2 Press .

Group number Track number

English Editing MDs English

• You can also select a track number with

, or the number buttons. Refer to

"Using the number buttons" ( page 17).

3 Press .

4 Press or to select

the group to which you want to add the track.

(Group 1 is selected in the example shown above)

5 Press . 6 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

• If you select a track already belonging to the group, "CANNOT ENTRY!" appears and you cannot proceed to the next step.

"G" stands for "GROUP".

• You can also select a track number with

, or the number buttons. Refer to

"Using the number buttons" ( page 17).

• You can also select a group number with

or .

3 Press . 4 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

• If you select the first track in the group or a track not belonging to the group, you cannot proceed to the next step.

• When you divide a group that has a title, the same title is given to both divided sections.

(Continued) Editing Tracks by Group

Introduction

Joining Groups (JOIN GR)

You can join two adjacent groups.

Example: Joining group 1 and group 2

Group 1 Group 2

Group 1

■ While the track in the second group to which you want to join the first group (group 2 in the example shown above) is being played back

1 Press repeatedly to select

"JOIN GR?".

2 Press .

Moving a Group (MOVE GR)

Example: Moving group 2

Group 1 Group 2

■While a track in the group you want to move (group 2 in the example shown above) is being played back

1 Press repeatedly to select

"MOVE GR?".

2 Press .

• Two adjacent group numbers appear. When no group is formed in the MD, "--" appears.

• You can also select a group number with

or .

3 Press . 4 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

• You cannot join two groups separated by a track not belonging to either group. "CANNOT JOIN" appears, and display returns to the previous step.

Group 1 Group 2

Track not belonging to either group

• When you join two groups that have titles, the title of the first group remains as the title of the joined group.

• You can also select a group number with

or .

3 Press . 4 Press or to select

the group number to which you want to move the specified group.

(Group 1 is selected in the example shown above)

5 Press . 6 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

For the locations of remote control buttons, refer to page 58.

Canceling a Group (UNGROUP/UNGR ALL)

Canceling a specified group (UNGROUP)

Example: Canceling group 1

Group 1 Group 2

Group 1

■ While a track in the group you want to cancel (group 1 in the example shown above) is being played back

1 Press repeatedly to select

"UNGROUP?".

2 Press .

Example: When you want to cancel group 1

English Editing MDs English

Canceling all groups (UNGR ALL)

Example: Canceling all groups

Group 1 Group 2

1 Press repeatedly to select

"UNGR ALL?".

• "UNGR" stands for "UNGROUP".

2 Press . 3 Press .

NOTE

• You can quit the editing operation by pressing

• You can also select a group number with

or .

3 Press . 4 Press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

(Continued) Editing Tracks by Group

Erasing a Group (ERASE GR)

You can erase a group including all tracks in the group.

Example: Erasing group 2

Group 1 Group 2

Group 1

CAUTION

• Once you erase a track, you cannot retrieve it. Before erasing a track, confirm that you no longer need it.

Introduction

For the locations of remote control buttons, refer to page 58.

■ While a track in the group you want to erase (group 2 in the example shown above) is being played back

1 Press repeatedly to select

"ERASE GR?".

2 Press .

• You can also select a group number with

or .

3 Press . 4 Confirm that you no longer need

the tracks, and then press .

NOTE

• During editing, you can return to the previous step

by pressing . You can quit the editing operation

by pressing .

Using the Timers

Editing MDs/Convenient Functions

Set the clock beforehand ( page 17).

Example: Display while the sleep timer is set to

60 minutes

English Editing MDs/Convenient Functions English

Remote control mode selector

Number buttons

NOTE

• Set the remote control mode selector to AUDIO before using the number buttons.

Sleep Timer

When the specified time passes, the main unit automatically turns off.

Sleep indicator

NOTE

• When you set the sleep timer, the display window automatically dims.

• Before the clock has been set (While "0:00" is

flashing), when you press , "CLOCK ADJUST!" appears.

Changing the sleep timer setting

• Press repeatedly to select the time again.

Confirming the sleep timer setting (remaining time)

• With the sleep timer activated, press once.

Recording Timer

You can use the recording timer function to record FM/AM broadcasts or sound from other equipment to an MD or cassette tape. You can enter up to three timer settings in total for the recording timer and the playback timer

( page 70).

NOTE

• Timer settings remain unchanged until the timer is replaced by new setting.

Press .

• Each time you press , the time display (in minutes) toggles as follows.

Cancel (Sleep indicator disappears.)

1 Prepare to record.

Radio Preset the radio station whose

Other equipment

MD recording

Cassette tape recording

broadcast you want to record. ( page 21)

Follow the operation manual for the equipment.

Insert an MD. ( page 46)

Insert a cassette tape. ( page 43)

(Continued on next page)

(Continued) Using the Timers

Introduction

2 Press repeatedly to select

"TIMER1", "TIMER2" or "TIMER3".

Example: When "TIMER1" is selected

Timer number

3 Press . 4 Press , or to set the

starting time and ending time.

Example:To set the recording time from 6:30

a.m. to 6:45 a.m.

• You can use the number buttons to set the recording time. Refer to "Using the number

buttons" ( page 17).

• For setting the clock, refer to "Setting the Clock" ( page 17).

• When you want to record sound from other equipment, you cannot use the recording timer function to start playback on any equipment other than this product.

• "AUX-D" stands for "AUX-DIGITAL".

■When you want to record an FM/AM radio broadcast

• Press , and then press , or the number buttons to select the preset number of the radio station whose broadcast you want to record. Refer to "Using the number buttons" ( page 17).

10 Press .

• When you use an MD as the recording medium, proceed to step 11.

• When you use a cassette tape as the recording medium, the settings appear in the display window. Confirm the settings, and then proceed to step 13.

11 Press or to select the

MDLP mode ( page 51).

12 Press .

• The settings appear in the display window.

13 When the main unit is on, press

Entering the "hour" → → Entering the

"minute" →

5 Press or to select

"ONCE" or "EVERYDAY".

ONCE : The recording timer works

once.

EVERYDAY : The recording timer works

every day.

6 Press . 7 Press or to select "REC

TIMER".

• "REC" stands for "Recording".

8 Press . 9 Press or to select the

combination of a sound source and recording medium.

Example: To record an FM broadcast to an MD

to turn off the main unit.

• While the recording timer is functioning, the volume is set to "0" and no sound is produced from the speakers or headphones.

• The recording timer is available only when the main unit is turned off.

NOTE

• During operation, you can return to the previous

step by pressing . You can quit the recording

timer settings by pressing . The settings are not stored.

• When you want to change the track mark options, make the change before or after setting the

recording timer. ( step 3 and 4 on page 54)

Convenient Functions

For the locations of remote control buttons, refer to page 68.

Canceling the recording timer

In step 2 on page 69, select the timer number you

want to cancel, and then press . Even when you cancel the recording timer, the set-

ting remains stored.

Activating the recording timer again

In step 2 on page 69, select the timer number you

want to activate, and then press repeatedly until all of the setting procedure finishes. Then turn off the main unit.

NOTE

• When you want to activate two or three recording timers, leave a blank time of 2 or more minutes between the ending time of the first recording timer and the starting time of the second recording timer. If the blank time is less than 2 minutes, the second recording timer does not work.

• When the power plug is disconnected or the power is cut, the recording timer settings may be lost. If the settings are lost, set the clock and recording timer again.

Playback Timer

1 Prepare the sound source you

want to play back.

Disc Make sure that a disc is loaded.

( page 22)

Cassette tape

Radio Preset the radio station whose broadcast

Other equipment

Insert an MD. ( page 46)

Insert a cassette tape. ( page 43)

you want to listen to. ( page 21)

Follow the operation manual for the equipment.

2 Press repeatedly to select

"TIMER1", "TIMER2" or "TIMER3".

Example: When "TIMER2" is selected

Timer number

3 Press .

English Convenient Functions English

4 Press , or to set the

starting time and ending time.

Example: When you want to set the playback

time from 7:00 a.m. to 7:30 a.m.

• You can use the number buttons to set the playback time. Refer to "Using the number

buttons" ( page 17).

• For setting the clock, refer to "Setting the Clock" ( page 17).

Entering the "hour" → → Entering the

"minute" →

5 Press or to select

"ONCE" or "EVERYDAY".

ONCE : The playback timer works once. EVERYDAY : The playback timer works every

day.

6 Press . 7 Press or to select

"PLAY TIMER".

(Continued on next page)

(Continued) Using the Timers

Introduction

For the locations of remote control buttons, refer to page 68.

8 Press . 9

Press or to select the sound source you want to play back.

Example: When you want to listen to an AM

broadcast

• When you want to listen to sound from other equipment, you cannot use the playback timer function to start playback on any equipment other than this product.

• You cannot use the playback timer function together with program playback, repeat playback, random playback, or group playback of a disc or MD.

■ When you want to listen to an FM/AM radio broadcast

• (With "FM" or "AM" selected) Press ,

and then press , or the number buttons to select the preset number of the radio station whose broadcast you want to listen to ( page 21). Refer to

"Using the number buttons" ( page 17).

■ When you want to play back a DVD VIDEO or DVD AUDIO

• (With "DVD/CD" selected) Press twice. Regardless of the displayed numbers of group (G) and track (T), you can play back a DVD VIDEO or DVD AUDIO

only from the beginning of the disc.

■ When you want to play back a CD, VCD, SVCD or MD

• (With "DVD/CD" selected) Press

twice, and then press , or the number buttons to select the number of a track (T) from which you want to start playback. Refer to "Using the number buttons" ( page 17). The group

number (G) is ignored.

■ When you want to specify a track from which you want to start playback on an MP3 or WMA

• (With "DVD/CD" selected) Press ,

press , or the number buttons to select the group number (G) to be

played back, press , and then press

, or the number buttons to select the track number (T) to be played back. Refer to "Using the number buttons" ( page 17).

10 Press . 11 Press or to adjust the

playback volume.

12 Press .

• The settings appear in the display window.

13 When the main unit is turned on,

press to turn off the main unit.

• The playback timer is available only when the main unit is turned off.

NOTE

• During operation, you can return to the previous

step by pressing . You can quit the playback

timer settings by pressing . The settings are not stored.

• When the playback timer starts, the volume gradually increases to the selected level.

Canceling the playback timer function

In step 2 on page 70, select the timer number you

want to cancel, and then press . Even when you cancel the playback timer, the setting remains stored.

Activating the playback timer again

In step 2 on page 70, select the timer number you

want to activate, and then press repeatedly until all of the setting procedure finishes. Then turn off the main unit.

NOTE

• When you want to activate two or three playback timers, leave a blank time of 2 or more minutes between the ending time of the first playback timer and the starting time of the second playback timer. If the blank time is less than 2 minutes, the second playback timer does not work.

• When the power plug is disconnected or the power is cut, the playback timer settings may be lost. If the settings are lost, set the clock and playback timer again.

• When you operate the playback timer with a DVD VIDEO, DVD AUDIO or VCD, sound and video may not be played back automatically. A DVD VIDEO, DVD AUDIO or VCD may contain a disc menu that appears first when played back. Sound or video will not come out before you select the desired item to be played back on the disc menu.

Auto Standby

If no sound is produced for 3 minutes when a sound source other than the FM/AM radio is selected, the main unit automatically turns off.

■ When a sound source other than the FM/ AM radio is selected

Press .

"A. STANDBY" stands for "Auto Standby".

Auto standby indicator

Auto standby performance

While a disc, MD, or cassette tape is being played back or recorded:

When playback or recording finishes, auto standby starts the countdown (the "A. STANDBY" indicator flashes). When no operation is carried out within 3 minutes, the main unit automatically turns off. When you start playback or recording within 3 minutes, auto standby starts the countdown again after playback or recording finishes. When an operation other than playback and recording finishes and no operation is carried out within 3 minutes, the main unit automatically turns off.

Disc/MD Ejection Lock

English Convenient Functions English

You can prohibit ejection of a disc and MD.

■When the main unit is turned off

While holding down , press on the main unit.

Even if you press or , "LOCKED" appears in the display window and the disc or MD does not

come out. In addition, when you press or , while the main unit is turned off, "LOCKED" appears in the

display window and the main unit does not turn on.

Canceling the disc/MD ejection lock

■When the main unit is turned off

Carry out the operation explained above once again.

While you are listening to sound from other equipment:

When no sound is produced, auto standby starts the countdown (the "A. STANDBY" indicator flashes). When no operation is carried out within 3 minutes, the main unit automatically turns off.

"A. STANDBY OFF" indicator starts to flash 20 seconds before the main unit is to turn off.

Canceling auto standby

Press once again.

NOTE

• Leaving the volume at "0" is not the same as producing no sound, and therefore does not start the auto standby function.

Using AV COMPU LINK

The JVC AV COMPU LINK system allows you to enjoy video or audio with the simplest operation. If your JVC TV set supports the JVC AV COMPU LINK system, simply starting the main unit will automatically make all necessary settings on the TV to allow you to enjoy the playback.

Connection and Setting

Introduction

Operations

You can enjoy sound or video simply by starting playback on the main unit. You do not have to select the input setting for the TV, or turn on the TV beforehand.

1 Turn on the main power to the TV.

• Carefully read manuals of equipment to be connected.

COMPU LINK

Main unit JVC-made TV set

Set the main unit's AV COMPU LINK MODE setting ( page 40) as follows.

• When connecting to the VIDEO-1 input terminal of the TV: DVD 2

• When connecting to the VIDEO-2 input terminal of the TV: DVD 3

• When connecting to the VIDEO-3 input terminal of the TV: DVD 1

Audio cord with monaural miniplugs (not supplied)

AV C O MPU

LINK -II or -III

2 Insert a disc into the main unit.

3 Press on the main unit.

The following operation is performed automatically.

• The TV set will be turned on.

• TV input will be switched to external input (Video 1, 2 or 3) of the main unit.

When you turn off the main unit, power to the TV is not turned off.

Convenient Functions/Reference

Restrictions on MDs

Because the MD recording method has some restrictions, the following phenomena may occur. The phenomena are not a malfunction of this product.

Phenomenon Possible cause

"DISC FULL" appears even though recordable time as printed on the MD remains.

"DISC FULL" appears even though the track numbers and recordable time have not reached the limit.

You cannot join tracks or groups.

The remaining recordable time does not increase even after you have erased some tracks.

Sound drops out intermittently during fast forward or fast reverse.

Recorded time plus remaining time is shorter than the total recordable time printed on the MD.

Serial Copy Management System (SCMS)

Regardless of remaining recordable time, MDs have a limit on the number of recordable tracks. You cannot record 255 or more tracks to an MD. (You can record up to 254 tracks to an MD.)

Repeated partial erasure and recording creates many blanks on an MD. When you record a track to such an MD, the track is split up and a small portion of the track is recorded into each blank. When the number of such split portions increases, "DISC FULL" may appear. When a split portion is 8 or less seconds (in SP mode (the standard stereo recording mode)), you cannot join the track with another track. In addition, when you erase such portions, remaining recordable time does not increase. With a track split into many portions, fast forward or fast reverse may produce intermittent sound dropouts. You cannot join tracks that have different MDLP modes (SP/LP2/LP4).

MD recording is possible only when there is a blank of consecutive 12 or more seconds (in SP mode) on the MD. Actual recording time is shortened on an MD that contains many blanks.

English Convenient Functions/Reference English

The Serial Copy Management System protects copyright and allows only first-generation digital copies from the digitally recordable source.

CAUTION

• The SCMS does not permit you to record sound from a digitally recorded MD to other media as digital sound.

High Speed Copy Management System (HCMS)

You can record sound to an MD at a higher speed than normal recording. Therefore, restrictions are required in order to protect copyright. When you use this product to record a track of a CD with the high speed recording function, this product does not then permit you to use the high speed recording function to record the same track of the CD to an MD within 74 minutes of the start of the first recording. For instance, when you record the track 1 of a CD to an MD with the high speed recording function, you cannot record the track 1 again to an MD with the high speed recording function for 74 minutes after the first high speed recording started. In addition, you cannot record 101 or more tracks within 74 minutes with the high speed recording function.

Handling Discs/MDs/Cassette Tapes

Introduction

Handling discs

• Do not put adhesive tape or stickers, or write on a disc.

• Do not bend a disc.

• Be sure not to use heart/flower shaped discs or other irregularly shaped discs. The use of such discs damages the main unit.

Cleaning discs

Signal surface

Wipe a disc from the center outward with a soft cloth.

• Be sure not to use thinners, benzenes, cleaners for analog records, or other chemical agents.

Scratches concentrated on a certain part cause sound dropout.

Handling MDs

• Do not open the shutter. Forcibly opening the shutter will break the MD.

Handling cassette tapes

• A slack tape may become caught in the inner part of the main unit and damage the main unit. Before using a cassette tape, wind up any slack in the cassette tape as shown on the right. Do not pull out the tape or touch the tape's surface.

Cleaning the tape deck head

• Clean the head, pinch rollers and capstans approximately every 10 hours of playback time before the volume falls or sound quality deteriorates

Capstans

Cotton-tipped swab moistened with alcohol

Preventing the loss of important recorded sound

• A write protect knob is attached to an MD for preventing accidental erasure of recorded sound.

Write protect knob

Close the write protect knob before recording or editing.

NOTE

• Do not put labels such as those indicating CD/track titles or other notes on any part of an MD other than the specified position. If you insert an MD with a label extending beyond the specified area, a label that is peeling off, or any other improperly attached label, it may damage the main unit.

Open the write protect knob to avoid erasing sound.

Pinch roller Head Pinch roller

Cleaning the main unit cabinet

• Gently dust the cabinet surface with a soft dry cloth. When the cabinet is very dirty, dampen the cloth with a neutral detergent diluted with water, wring out the cloth well, and then wipe the cabinet with the dampened cloth followed by a soft dry cloth.

• Do not wipe the cabinet with thinners or benzenes. Wiping it with these agents may cause discoloration of the cabinet or removal of the paint. Do not spray insecticides or other highly volatile agents onto the cabinet. Do not leave pieces of rubber or plastic on the cabinet for a long period.

Reference

MD/Disc Messages

MD message Meaning Possible solution

CANNOT ENTRY!

CANNOT FORM! There is a group between the selected tracks.

CANNOT GROUP!

CANNOT JOIN

CANNOT LISTEN

CANNOT REC

CANNOT TITLE

READ ERROR The main unit cannot read the MD.

DISC FULL

DISC PROTECTED The MD is write-protected.

EMERGENCY STOP

GROUP FULL You are trying to form 100 or more groups. You can form up to 99 groups.

GROUP TRACK

LOAD ERROR The MD is not properly loaded. Insert the MD properly.

MD NO DISC No MD is loaded. –

NON-AUDIO CANNOT COPY

PLAYBACK DISC

SCMS CANNOT COPY

TRACK PROTECTED

HCMS CANNOT COPY

BLANK DISC There are no tracks in the MD. –

The track has already been in the selected group.

There is no space for storing more group information. (Group information is stored in the same area as title information.)

You are trying to join tracks that have different MDLP modes (SP/LP2/LP4), or tracks of only 8 or less seconds (in SP mode).

You are trying to adjust the volume during high speed recording.

You are trying to operate one-track-recording with a VCD or SVCD during PBC playback.

You are trying to enter a total of 1 793 or more characters to an MD.

There is no more space in the MD, or you are trying to record 255 or more tracks.

A malfunction occurred during recording.

You are trying to form a group with a track already belonging to another group.

You are trying to record digital sound other than linear PCM from the connected equipment to an MD.

You are trying to edit or record to an MD which is designed only for playback.

You are trying to make a digital audio duplication of a CD-R or CD-RW.

You are trying to divide, join, or erase tracks which are recorded in the Net MD format.

The tracks are write-protected by equipment other than this product.

You are trying to record a track with the high speed recording function within 74 minutes of starting to record the same track with the high speed recording function.

Select an appropriate track. ( page 64)

Select appropriate tracks. ( page 63)

You cannot form a group any more on the MD. (Erase the disc or track titles you do not need.)

The MD system restricts such operation.

You cannot listen to sound from a CD during high speed recording.

Set PBC to off ( page 24).

You cannot enter more titles.

Turn off the main unit. If the same message appears again, the MD may be damaged. Replace the MD.

Replace the MD. ( page 74).

Close the write protect knob on the MD.

page 75).

(

Press to quit recording, press to eject the MD, and then start recording again.

Select tracks that do not belong to any groups. ( page 63)

Set digital output to linear PCM on the connected digital equipment. (Refer to the instruction manual for the connected equipment for details.)

Replace the MD with a recordable MD.

Operate analog recording at normal speed. ( page 53)

Edit the tracks on equipment compatible with Net MD.

Edit the tracks with the equipment on which the tracks were recorded.

Wait 74 minutes, or change from high speed recording to normal speed recording.

English Reference English

Disc message Meaning Possible solution

CANNOT PLAY

NO DISC No disc is loaded. –

NO AUDIO The disc may be an illegally copied disc. You cannot listen to the disc.

LR ONLY

You are trying to play back an unplayable disc or a disc that has many scratches.

You are playing back a multi-channel track for which down-mix is prohibited.

Replace the disc.

This is normal operation.

Troubleshooting

Introduction

Problem Possible cause Possible solution

No sound/video is produced.

The clock display is flashing.

Disc playback does not start.

A certain point cannot be played back properly.

The volume of cassette tape playback is low.

You cannot record an MD/cassette tape.

A radio broadcast cannot be received.

A whirring noise is produced.

You cannot set the timer. You did not set the clock. Set the clock. 17

The timer does not work. The main unit is turned on.

You cannot operate the remote control.

You cannot operate the main unit with the number buttons on the remote control.

When you turn on the main unit, a noise comes out from the rear of the main unit.

Improper connection. Connect all cords properly. 11

Headphones are connected. Disconnect the headphone plug. 8

A power failure occurred or the power plug was disconnected.

The disc is upside down.

Moisture has condensed on the lens.

The disc is scratched or dirty. Clean or replace the disc. 75

An error occurred on the MD. Record to the MD again. 51

The head or capstans are dirty. Clean the head or capstans. 75

The MD/cassette tape is writeprotected.

No antenna is connected. Connect an antenna. 11

The main unit is located close to a TV, computer, or other electric appliance.

The remote control batteries are running low.

The remote control mode selector on the remote control is set to TV.

The internal cooling fan produces the noise as it rotates.

Reset the clock. 17

Place the disc on the disc tray with the letter-printed surface facing up.

Leave the main unit turned on, wait for approximately 1 or 2 hours, and then operate the main unit.

Cancel the write-protection. 55, 75

Place the main unit away from a TV, computer, or other electric appliance.

After setting the timer, turn off the main unit.

Replace the batteries with new batteries.

Set the remote control mode selector to AUDIO.

The noise is not a malfunction. This is to prevent excessive heat.

Reference

page

69, 71

13, 18

● If this product does not function properly even after you have implemented the possible solutions given above

Many functions of this product are implemented by microcomputers. If malfunction is caused by thunder or static electricity, or the main unit does not function properly even when you press a button, disconnect the power plug from the AC outlet, wait for a while, and then connect this product again. Then reset the clock.

Specifications

■MD/DVD receiver (CA-UXQD7)

Amplifier

Output power 20 W + 20 W at 4 Ω

(10% THD)

Input terminals

<Analog> AUX×1,

500 mV/47 k 250 mV/47 k

<Digital> Digital optical input × 1

-23 dBm to -15 dBm (Optical square terminal) (Compatible with frequency of 32 kHz, 44.1 kHz and 48 kHz)

Output terminals

<Analog> Speaker×1, 20 W/4

Impedance 4 Ω - 16 Headphone (×1), 25 mW/32 Impedance 16 Ω - 1 k

<Digital> DVD/CD optical input × 1

-23 dBm to -15 dBm (Optical square terminal)

<Other> AV COMPU LINK × 2 (

Tuner

Frequency FM:87.50 MHz - 108.00 MHz

AM:531 kHz - 1 710 kHz (9 kHz spacing) 530 kHz - 1 710 kHz (10 kHz spacing)

DVD player

Playable discs DVD VIDEO, DVD AUDIO,

CD, VCD, SVCD, CD-R/CDRW (CD, VCD, SVCD, MP3/ WMA/JPEG format), DVD-R/ DVD-RW (video format)

MD recorder

Audio playing MiniDisc digital audio system

system

Recording system Magneto-optical overwrite

system

Reading system Non-contact, semiconductor

laser pickup

Recording/Playback time (when using an 80-minute MD)

SP: 80 minutes

LP2: 160 minutes

LP4: 320 minutes

Sampling frequency 44.1 kHz

Audio compression ATRAC (Adaptive TRansform

system Acoustic Coding)/ATRAC3

(MDLP)

Ω

:LEVEL1

Ω

:LEVEL2

Ω

3.5)

Cassette deck

Frequency response

Normal (type I) 60 Hz - 14 000 Hz

Wow and flutter 0.15% (WRMS)

English Reference English

General

Power source AC 220 V , 50 Hz

Power consumption 70 W (at operation)

Dimensions 165 mm (W) × 200 mm (H)

Mass (approx.) 5.1 kg

1.3 W (on standby)

× 355 mm (D)

■Speaker (SP-UXQD6)

System 3-way bass reflex type,

Ω

Speakers Woofer: 10 cm × 1

Power handling 20 W

capacity

Impedance 4

Frequency range 58 Hz - 40 kHz

Sound pressure 85 dB/W•m

Dimensions 135 mm (W) × 200.5 mm (H)

Mass (approx.) 2.0 kg

Magnetically shielded type

Midrange: 4 cm × 1 Tweeter: 1.5 cm × 1

Ω

level

× 211.5 mm (D)

(1 unit)

■Micro component MD system (UX-QD7)

General

Dimensions 435 mm (W) × 200.5 mm (H)

Mass (approx.) 9.1 kg

• U.S. and foreign patents licensed from Dolby Laboratories.

× 355 mm (D)

EN,CS

2004VictorCompanyofJapan,Limited

0904SKMMODJEM

JVC LVT1220-002A User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

INSTRUCTIONS

Warnings, Cautions and Others

Table of Contents

Notes on Operation

Special Cautions

Part Description

Remote Control

Connections

Basic Operations

Listening to Radio Broadcasts

Basic Operations of the DVD Player

Convenient Functions of the DVD Player

Status Bar and Menu Bar

Playing Back MP3/WMA and JPEG Discs

Preferences

Country/Area Codes

Language Codes

Listening to Cassette Tapes

Listening to Other Equipment

Listening to MDs

Recording Sound to MDs

Recording Sound to Cassette Tapes

Giving (Editing) Titles

Editing Tracks

Editing Tracks by Group

Using the Timers

Auto Standby

Disc/MD Ejection Lock

Using AV COMPU LINK

Restrictions on MDs

Handling Discs/MDs/Cassette Tapes

MD/Disc Messages

Troubleshooting

Specifications