JVC LT-42Z48 User Guide

LT-42Z48
WIDE LCD PANEL TV
INSTRUCTIONS
À¤²©q®/&'¿¨n³ ´¿±´³¤Án³
ENGLISH
¡³ª³Â£
GGT0253-001A-H

Warning

Follow this manual regarding setup!
z Connect only to a 110 - 240 V,
50/60 Hz AC outlet.
Please follow all the guidelines below
Do not allow the TV to fall!
z Do not rest your elbows on, or allow children to hang from the TV.
There is a risk that the TV will fall and cause injuries.
z Make use of the hole on the back of the stand to prevent the TV from
falling easily. (P. 6)
Make enough room for inserting and removing the power plug!
Place the TV as close to the outlet as possible!
z Even if the TV’s power lamp
is unlit, the main power supply is not cut off unless the power cord is unplugged. The main power supply for this TV is controlled by inserting or removing the power plug.
Never cut or damage the
Never try to repair the TV yourself!
g If the problem cannot be
solved in “Troubleshooting” (P. 26), unplug the power cord and contact your retailer.
power cord!
z If the power plug is
not the right shape, or the power cord is not long enough, use an appropriate plug adapter or extension cable. (Consult your retailer.)
Unplug the power cord when going out!
z The power buttons
on the remote control and the TV unit cannot completely turn off the TV. (Make appropriate arrangements for bedridden people.)
For more details on installation, usage and safety g Consult your retailer
When attaching the TV to the wall, use the optional JVC wall mounting unit!
z Consult a qualified technician. z See the included manual on
mounting procedures.
z JVC assumes no responsibility
for damage due to improper mounting.
If the TV is damaged or behaving strangely, stop using it at once!
g Unplug the power cord
and contact your retailer.
Handle LCD panel with care!
z Use a soft, dry cloth when
cleaning.
Never dismantle the rear panel!
z It may cause an electric shock.
Never place anything on the TV!
z Placing liquids,
naked flames, cloths, paper, etc. on the TV may cause a fire.
Never expose to rain or moisture!
z To prevent fire or
electric shock, never allow liquids to enter the unit.
Never insert objects into the cabinet openings!
z It may cause a fatal
electric shock. Take care when children are near.
Never obstruct the ventilation holes!
z It may cause overheating or a
fire.
Never listen to headphones at high volume!
z It may damage your hearing.
Hold the TV so as not to scratch the screen!
z Do not touch the screen when
carrying the TV.
Do not carry the TV on your own!
z In order to prevent
accidents, ensure that the TV is carried by two or more people.
To set up your TV
Please read “Getting started” (P. 6 - 11). The main descriptions are in the following pages.
Connecting the external devices and aerial
PAG E8PAG E
7
Contents
First things first!
Getting started
z Warning.............................................. 1
z Remote control................................... 3
z Names and functions of parts ............4
z Getting started ...................................6
ENGLISH
IMPORTANT
PREPARE
Language
ENGLISH
Initial settings
Editing channels
PAG E
9
PAG E
10
Let’s try it out
Try the advanced features
Just the way you like it
When you have trouble
z Enjoy your new TV!..........................12
z Watching TV.....................................13
z Viewing Teletext ...............................14
z Watching videos / DVDs ..................15
z Useful functions ...............................16
z Configuring your remote control....... 17
z Customising your TV........................ 19
Picture.............................................19
Features (sub menu)....................... 20
Sound.............................................. 21
Features..........................................22
Set Up ............................................. 24
z Troubleshooting ...............................26
z Technical information ....................... 28
z “CH/CC” list......................................29
z Specifications...................................30
USE SETTING
TROUBLE?

Remote control

Mute
Return to a frequently watched channel (P. 13)
Turn on “Clear SD” (P. 20)
Switch between “TV / STB / DVD / AUDIO” (P. 17)
Switch between TV / VIDEO devices
Volume control / Turn off muting
Display PR List and channel information
Choose a favourite channel (P. 13)
Change the aspect ratio (P. 16)
Turn on “Sound Effect” (P. 16)
2%452.
#LEAR3$
466)$%/
VOL
TOP MENU
$)30,!9
MODE
ST
CH
CH
LCD
B
AUDIO
VOL
SLEEP TIMER
Turn on / off (standby) the TV
Enter channel / page number
View Teletext (P. 14)
Colour buttons
Display on-screen menu (P. 19) Select and confirm settings in menus
Change channel / page For Hyper Scan, press and hold CH or CH , PR changes
without changing the picture screen. Once you release the button, the picture of the selected PR will appear.
To the previous screen
Functions for viewing Teletext (P. 14)
Set the sleep timer (P. 16)
Select a picture mode (P. 16)
Note
z For buttons that can be used to operate other devices, refer to
“Configuring your remote control” (P. 17).

Names and functions of parts

ENGLISH
TV/VIDEO
MENU/OK
CHANNEL
VOLUME
Switch between TV / VIDEO devices Display on-screen menu / set
Change channel / page / Hyper Scan (P. 3)
Volume / adjust
Turn On / Off (standby) the TV
Remote control sensor
To headphones
Power lamp
ON: Lit (Blue) OFF: Unlit
z When “Power Lamp” is set to “Off”, the Power lamp will not light up.
g“Power Lamp” (P. 23)
IMPORTANT
PREPARE
USE SETTING
TROUBLE?
ENGLISH
Names and functions of parts
Change the direction of TV Attach the stand to the TV
Insert the stand into the panel at the position where the screw holes are and fasten the screws (x 4, provided).
1
2
Note
z If you face any problem with the stand assembly, please contact your
retailer or authorised dealer.

Getting started

Please read P. 7 - 11 of this manual to set up your TV.
Check accessories
Remote control RM-C1940
z Stand and screws are also included. For details, refer to page 5.
“AAA/R03” Batteries (For confirming the TV works)
WARNING:
Batteries shall not be exposed to excessive heat such as direct sunshine, fire or the like.
Installation requirements
z Place the TV on a flat and stable location. z To avoid overheating, ensure the unit has ample room.
200 mm
150 mm 50 mm
z To prevent the TV from falling, thread the belt through the hole on the back
of the stand and secure it to the TV rack, etc.
Belt and screw (not provided)
150 mm 50 mm
Hole
ENGLISH
IMPORTANT
PREPARE
USE SETTING
Install your TV
Power requirements
z Connect the power cord only to a 110 - 240 V, 50/60 Hz AC outlet.
When attaching the TV to the wall, use the optional JVC wall mounting unit
z Consult a qualified technician. z See the included manual on mounting procedures. z JVC assumes no responsibility for damage due to improper mounting. z Mounting holes for wall mounting unit:
M5 x 4, 400 mm x 200 mm Depth of screw hole is 13 mm from the surface of the TV.
ENGLISH
Insert the batteries
Use two “AAA/R03” dry cell batteries. Insert the batteries from the - end, making sure the + and - polarities are correct.
If this symbol is shown, it is only valid in the European Union.
TROUBLE?
Connecting your external devices
Make sure all the devices and the TV are turned off. You can connect many different devices to the rear panel of the TV. Please read the user manuals of each device before setting up. (Connecting cables are not supplied with this TV.)
Component input
Pb
Pr
Y
VIDEO-1
R
V
L
DVD Player
Composite input
Pb
Pr
Y
VIDEO-1
R
V
L
Game
consoles
Video
camera
VCR
JVC
g
: signal direction
HDMI-1 HDMI-2 HDMI-3
Not available. (For service adjustments)
Digital Satellite broadcast tuner
HD Video
camera
DVD player
Getting started
VIDEO-1
z Use component signal
g “VIDEO Setting” (P. 24)
VIDEO-2
z If both composite and S-VIDEO cables
are connected, S-VIDEO input takes priority over composite inputs.
HDMI-1 HDMI-2 HDMI-3
z “HDMI-1 Audio Setting” g (P. 24) z HDMI-2 and HDMI-3 inputs do not
support analogue sound.
Watching videos
Output j Input h
Composite signal /
Component signal (P. 31)
Sound L / R
Watching videos
Output j Input h
Composite signal /
S-VIDEO
Sound L / R
Connecting HDMI devices
Output j Input h
HDMI signal
(P. 31)
DVD player
(HDMI compatible)
PC
PC input line in
L
R
HDMI-1
( DVI
ANALOG AUDIO )
PC AUDIO
Pb
Pr
R
R
R
Y
VIDEO-1
V
L
L
L
V
PC IN
(D-SUB)
S
OUTPUT
To VIDEO-2
PC
VIDEO-2
V
Game
consoles
Video
camera
OUTPUT
Video and sound signals of a TV channel you are viewing output from th ese terminals
Output j
Composite signal
Sound L / R
JVC
DVI devices
g“Connect DVI devices”
(P. 28)
Connecting an aerial and VCR / DVD player
VIDEO-2
R
L
V
S
AERIAL
VIDEO-2
OR
VCR / DVD player
z After all the connections have been made, insert the plug into an
AC outlet.
ENGLISH
IMPORTANT
PREPARE
USE SETTING
TROUBLE?
ENGLISH
Initial settings
Ini
The initial settings will begin automatically when the TV is turned on for the very first time. Follow the on-screen instructions to perform the settings.
1 Turn on
z If the remote control doesn’t work,
confirm that the mode is set to “TV”.
2 Start initial settings
Getting started
4 Select the Teletext language group
Teletext Language
Group-1
Group-2 Group-3 Group-4 Group-5
5 Automatically register channels
Auto Program
CH 02
0%
select
LCD
z If the JVC logo does not appear, refer to “To perform initial
settings again”.
3 Select a language
Language
 To the previous screen g  Exit g  To perform initial settings again
Take note that performing initial settings again will cause all channel related settings to be lost. Press the “MENU” button to display the menu, then press and hold the number button “1” for more than 3 seconds to start initial settings.
If you wish to make changes later
g“Language” and “Auto Program” (P. 24)
A select
B set
6 Check what was registered
Edit
PR ID AV
01 CH
02 CH 03 CH 04 05 06 07
_ _ _ _ _
CH/CC
CH CH CC CC
02
03 04 05 06 01 02
To edit channels
g“Editing channels” (P. 10)
7 Finish
select a channel
+ 23 hidden pages