SPEAKER STAND
LS-M1
English
English
INSTRUCTIONS
LVT1248-002A
[US]
Thank you for purchasing a JVC product.
Before you begin using it, please read the instructions carefully.
Warnings, Cautions and Others
English
Warning
Observe the following carefully before installation;
otherwise, the speaker may fall over, causing damage or
injury.
– Do not install the speaker stand on an uneven surface
or in a place subject to vibration.
– Do not lean against the speaker stand. Especially pay
attention to children not to do so.
– Fasten all the screws firmly when assembling the
speaker stand, and check its tightness afterwards
regularly.
– Do not install any overweight equipment (over 10 kg)
on the speaker stand.
7 Checking the supplied parts
Check to be sure you have the following supplied parts.
The quantity of piece supplied is for one pair of speaker stands.
Top plate--------------------- 2 Bottom plate--------------- 2
7 Precautions
• For safety use
– Do not climb or hang on to the speaker stand.
– Attach the speaker firmly to the speaker stand.
• For installation
– While installing the speaker on the stand, do not drop it from
the stand. Pay attention not to damage the speaker cabinet.
–To obtain the best bass sound quality, install the speaker
stand on the flat floor.
• For daily use
– Wipe with a dry, soft cloth if the speaker stand should
become dirty. If very dirty, wipe with a cloth applied a small
amount of water or neutral detergent, then wipe with a dry
cloth.
– Do not use chemicals such as benzine and thinner for
cleaning the speaker stand; otherwise, the speaker stand
may deteriorate or its paint may come off.
Leg ------------------------ 2
Leg ------------------------ 4
Screws ------------------- 6
(Black: M6 x 30 mm) (Black: M6 x 16 mm)
If any item is missing, contact your dealer immediately.
Screws ------------------- 6
(thick)
Screws ------------------- 4
(Silver: M5 x 28 mm)
(thin)
Leg holder ------------------ 6
2
Assembly Installing Speaker
330260
632
585 1530
2
Before assembling—
• Prepare a Phillips screwdriver.
• Place a large, thick cloth on the floor where you assemble the
speaker stand to protect the floor and the speaker stand.
7 Assembling the speaker stand
• Tighten the screws firmly so that no space is left between
the legs and plates.
1
Fix the top plate.
• Align the projection of the legs to the holes of the top plate
correctly, then attach them with three of the supplied
screws B (M6 x 16 mm).
Leg B (thin)
Screws B
(M6 x 16 mm)
Leg A (thick)
Top plate
* The side without spacer should face outside.
2
Fix the bottom plate and leg holders.
• Align the projection of the legs to the holes of the bottom
plate correctly, then attach them with three of the supplied
screws A (M6 x 30 mm).
7 Attach the speaker on the stand
1
Locate the speaker properly by aligning both screw holes
of the speaker and the speaker stand.
• Do not install the speaker stand on an uneven surface or in
a place subject to vibration.
• Do not install any overweight equipment (over 10 kg) on the
speaker stand.
2
Fix the speaker with the supplied screws C (M5 x 28 mm).
• Do not overtighten the screws, but firmly enough to prevent
the speakers from being shaky.
Spacer
Screw C (M5 x 28 mm)
English
Screws A
(M6 x 30 mm)
Leg holder
Leg B (thin)
Spacer
Bottom plate
Leg A (thick)
Spacer
Thick cloth
(not supplied)
Specifications
Mass: 5.3 kg each
Maximum load: 10 kg
Dimensions: See the diagram.
Unit: mm
Design and specifications subject to change without notice.
3
Finally tighten screws A and B fully.
• Tighten them firmly and fully so that no space is left between
the legs and plates.
3
LS-M1
SPEAKER STAND
EN, CS, CT
© 2004 Victor Company of Japan, Limited
1104NSMMDWHCE
Loading...