JVC KS-T807EE User Manual

CASSETTE RECEIVER

РЕСИВЕР С КАССЕТНЫМ ПРОИГРЫВАТЕЛЕМ

KS-T807/KS-T707

KS-T807

KS-T707

For installation and connections, refer to the separate manual.

Указания по установке и выполнению соединений приводятся в отдельной инструкции.

В соответствии с Законом Российской Федерации “О защите прав потребителей” срок службы
(годности) данного товара “по истечении которого он может представлять опасность для жизни,
здоровья потребителя, причинять вред его имуществу или окружающей среде” составляет семь (7) лет
со дня производства. Этот срок является временем, в течение которого потребитель данного товара
может безопасно им пользоваться при условии соблюдения инструкции по эксплуатации данного
товара, проводя необходимое обслуживание, включающее замену расходных материалов и/или
соответствующее ремонтное обеспечение в специализированном сервисном центре.

Дополнительные косметические материалы к данному товару, поставляемые вместе с ним, могут
храниться в течение двух (2) лет со дня его производства.

Срок службы (годности), кроме срока хранения дополнительных косметических материалов,
упомянутых в предыдущих двух пунктах, не затрагивает никаких других прав потребителя, в частности,
гарантийного свидетельства JVC, которое он может получить в соответствии с законом о правах
потребителя или других законов, связанных с ним.

ENGLISH

РУCCKИЙ

INSTRUCTIONS

ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ

GET0212-001A

[EE]

How to reset your unit

After detaching the control panel, press the reset button on the panel holder using a ball-point pen
or a similar tool.
This will reset the built-in microcomputer.

ENGLISH

Note:

Your preset adjustments—such as preset channels or sound adjustments—will also be erased.

How to use the M MODE button

If you press M MODE, the unit goes into functions mode, then the number buttons work as different
function buttons.

• When connecting a JVC MP3-compatible CD changer: The 5/∞ buttons will also work as

+10/–10 buttons after pressing M MODE.

Ex.: When number button 2 works as MO (monaural) button.

Time countdown indicator

To use these buttons for original functions again after pressing M MODE, wait for 5 seconds
without pressing any of these buttons until the functions mode is cleared.

• Pressing M MODE again also clears the functions mode.

2

Thank you for purchasing a JVC product. Please read all instructions carefully before operation,

to ensure your complete understanding and to obtain the best possible performance from the unit.

CONTENTS

How to reset your unit ............................... 2

How to use the M MODE button ............... 2

LOCATION OF THE BUTTONS ............ 4

Control panel............................................. 4

BASIC OPERATIONS ....................... 5

Turning on the power ................................ 5

Setting the clock........................................ 6

RADIO OPERATIONS ...................... 7

Listening to the radio................................. 7

Storing stations in memory ....................... 9

Tuning in to a preset station ...................... 10

RDS OPERATIONS ......................... 11

What you can do with RDS ....................... 11

Other convenient RDS functions and

adjustments ............................................ 15

TAPE OPERATIONS ........................ 18

Listening to a cassette .............................. 18

Finding the beginning of a tune................. 19

Other convenient tape functions ............... 19

Prohibiting cassette ejection ..................... 20

SOUND ADJUSTMENTS ................... 21

Selecting preset sound modes

(C-EQ: custom equalizer) ....................... 21

Adjusting the sound .................................. 22

OTHER MAIN FUNCTIONS ................ 23

Changing the general settings (PSM) ....... 23

Changing the standard plate

(only for KS-T807) .................................. 26

Detaching the control panel ...................... 28

CD CHANGER OPERATIONS .............. 29

About MP3 discs ....................................... 29

Playing discs ............................................. 30

Selecting the playback modes .................. 32

EXTERNAL COMPONENT OPERATIONS ... 33

Playing an external component................. 33

DAB TUNER OPERATIONS ................ 34

Tuning in to an ensemble and one of the

services .................................................. 34

Storing DAB services in memory .............. 35

Tuning in to a preset DAB service ............. 36

What you can do more with DAB .............. 37

PREPARING THE REMOTE

CONTROLLER............................. 38

Remote controller...................................... 39

TROUBLESHOOTING ...................... 40

MAINTENANCE ............................. 42

SPECIFICATIONS........................... 43

ENGLISH

BEFORE USE

*For safety....

• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.

• Stop the car before performing any complicated
operations.

*Temperature inside the car....

If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.

3

LOCATION OF THE BUTTONS

Control panel

Display window

ENGLISH

1 Remote sensor
2 Control dial
3 (standby/on/attenuator) button
4 SEL (select) button
5 Screws—M2 × 5 mm (only for KS-T807)
6 Plate cover and standard plate

(only for KS-T807)

7 FM/AM DAB button
8 5 (up) button

23 (tape direction) button

9 0 (eject) button
p 4 /¢ buttons
q (control panel release) button
w DISP (display) button

• Also functions as SSM buttons when pressed

e M MODE button

• Also functions as SSM buttons when pressed

r Display window
t EQ (equalizer) button
y MO (monaural) button
u RPT (repeat) button
i RND (random) button

• Functions only when connecting to a CD changer.

o Number buttons

4

d

1

together with M MODE button.

together with DISP (display) button.

ghjkl/ z xcv

f

23 4

r

ewq

t

b

5

yui

; T TP/PTY (traffic programme/programme

type) button

a TAPE CD-CH (CD changer) button
s ∞ (down) button

6

;

o

a

Display window

d LOUD (loudness) indicator
f EQ (equalizer) indicator
g (tape-in) indicator
h TAPE indicator
j CD-CH (CD changer) indicator
k FM band indicators—FM1, FM2, FM3
l AM band indicator
/ Tuner reception indicators—MO (monaural),

ST (stereo)

z RDS indicators—AF, REG, TP, PTY
x Volume (or audio) level indicator
c MP3 indicator

• Lights up only when playing an MP3 disc on
a JVC MP3-compatible CD changer.

v (disc) indicator

• Lights up only when connecting to a CD changer.

b Main display
n RND (random) indicator

• Lights up only when connecting to a CD changer.

m RPT (repeat) indicator

mn

78 9

s

p

BASIC OPERATIONS

* The control panel

illustrations used for
explanation in this manual
is KS-T707.

ENGLISH

3

1

Turning on the power

1

Turn on the power.

Note on One-Touch Operation:

When you select a source in step 2 below, the
power automatically comes on. You do not have
to press this button to turn on the power.

2

Select the source.

To operate the tuner (FM or AM),

see pages 7 – 17.

To play a tape,

see pages 18 – 20.

To operate the CD changer,

see pages 29 – 32.

To operate the external component

(LINE IN), see page 33.

To operate the DAB tuner,

see pages 34 – 37.

2

3

Adjust the volume.

To increase the volume

To decrease the volume

Volume (or audio) level indicator

(see page 25)

Volume level appears.

4

Adjust the sound as you want. (See
pages 21 and 22.)

To drop the volume in a moment

Press briefly while listening to any
source. “AT T ” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the
button briefly again.

• If you turn the control dial, you can also restore
the sound.

To turn off the power

Press and hold for more than one
second.

“SEE YOU” appears, then the unit turns off.

5

ENGLISH

Setting the clock

You can also set the clock system to either
24 hours or 12 hours.

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 24.)

2

Set the hour.

1 Select “CLOCK H” (hour) if not shown on

the display.

2 Adjust the hour.

12

3

Set the minute.

1 Select “CLOCK M” (minute).
2 Adjust the minute.

12

5

Finish the setting.

To check the current clock time or change the
display mode

Press DISP (display) repeatedly.
Each time you press the button,
the display mode changes as
follows:

• During tuner operation:

Frequency

• For the indication change during RDS
operation, see page 16.

• For the indication change during DAB
operation, see page 35.

• During tape operation:

Play mode (TAPE)

• During CD changer operation:

Elapsed playing time

• During external component operation:

LINE IN

Clock

Clock

Disc number

Clock

Clock

4

Set the clock system.

1 Select “24H/12H.”
2 Select “24H” or “12H.”

12

6

• During power off:

The power turns on and the clock time is shown
for about 5 seconds, then the power turns off.

RADIO OPERATIONS

ENGLISH

Listening to the radio

You can use either automatic searching or manual
searching to tune in to a particular station.

Searching for a station automatically:
Auto search

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

Selected band appears.

Lights up when receiving an FM stereo
broadcast with sufficient signal strength.

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.

2

Start searching for a station.

To search for stations of
higher frequencies

To search for stations of lower frequencies

When a station is received, searching stops.

To stop searching before a station is received,

press the same button you have pressed for
searching.

Note:

FM1 and FM2: 87.5 MHz – 108.0 MHz

FM3: 65.00 MHz – 74.00 MHz

7

Searching for a station manually:
Manual search

1

Select the band (FM1 – 3, AM).

ENGLISH

Note:

This receiver has three FM bands (FM1, FM2,
FM3). You can use any one of them to listen to
an FM broadcast.

2

Press and hold ¢ or 4
until “M” (manual) starts flashing on
the display.

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

When an FM stereo broadcast is hard to
receive:

1 Press M MODE to enter the

functions mode while listening to
an FM stereo broadcast.

2 Press MO (monaural), while still in

the functions mode, so that the
MO indicator lights up on the
display.
Each time you press the button,
the MO indicator lights up and
goes off alternately.

MO (monaural) indicator

When the MO indicator is lit on the display, the
sound you hear becomes monaural but the
reception will be improved.

3

Tune in to a station you want while
“M” (manual) is flashing.

To tune in to stations of
higher frequencies

To tune in to stations of lower frequencies

• If you release your finger from the button,
the manual mode automatically turns off
after 5 seconds.

• If you hold down the button, the frequency
keeps changing—in 50 kHz intervals
(87.5 MHz — 108.0 MHz for FM 1 and FM

2), in 30 kHz intervals (65.00 MHz — 74.00
MHz for FM 3) and 9 kHz for AM—MW/LW
until you release the button.

8

Storing stations in memory

You can use one of the following two methods to
store broadcasting stations in memory.

• Automatic preset of FM stations: SSM (Strong­station Sequential Memory)

• Manual preset of both FM and AM stations

FM station automatic preset: SSM

You can preset 6 local FM stations in each FM
band (FM1, FM2, and FM3).

1

Select the FM band (FM1 – 3) you
want to store FM stations into.

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

2

Press and hold both buttons for
more than 2 seconds.

Manual preset

You can preset up to 6 stations in each band
(FM1, FM2, FM3, and AM) manually.

Ex.: Storing FM station of 92.5 MHz into the

preset number 1 of the FM1 band.

1

Select the band (FM1 – 3, AM) you
want to store stations into (in this
example, FM1).

Each time you press the
button, the band changes as
follows:

FM1 FM2 FM3 AM

2

Tune in to a station (in this example,
of 92.5 MHz).

To tune in to stations of
higher frequencies

To tune in to stations of lower frequencies

ENGLISH

“SSM” appears, then disappears when
automatic preset is over.

Local FM stations with the strongest signals are
searched and stored automatically in the band
number you have selected (FM1, FM2, or FM3).
These stations are preset in the number buttons
—No.1 (lowest frequency) to No.6 (highest
frequency).
When automatic preset is over, the station stored
in number button 1 will be automatically tuned in.

CONTINUED ON THE NEXT PAGE

9

3

Press and hold the number button
(in this example, 1) for more than 2
seconds.

ENGLISH

Tuning in to a preset station

You can easily tune in to a preset station.
Remember that you must store stations first. If
you have not stored them yet, see “Storing
stations in memory” on pages 9 and 10.

1

Select the band (FM1 – 3, AM).

Each time you press the
button, the band changes as
follows:

Preset number flashes for a while

4

Repeat the above procedure to store
other stations into other preset
numbers.

Notes:

• A previously preset station is erased when a new
station is stored in the same preset number.

• Preset stations are erased when the power supply to
the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset
the stations again.

FM1 FM2 FM3 AM

2

Select the number (1 – 6) for the
preset station you want.

10

RDS OPERATIONS

What you can do with RDS

RDS (Radio Data System) allows FM stations to
send an additional signal along with their regular
programme signals. For example, the stations
send their station names, as well as information
about what type of programme they broadcast,
such as sports or music, etc.
Another advantage of RDS function is called
“Enhanced Other Networks.” By using the
Enhanced Other Networks data sent from a
station, you can tune in to a different station of a
different network broadcasting your favorite
programme or traffic announcement while
listening to another programme or to another
source such as tape.

By receiving the RDS data, this unit can do the
following:

• Tracing the same programme automatically
(Network-Tracking Reception)

• Standby Reception of TA (Traffic
Announcement) or your favorite programme

• PTY (Programme Type) search

• Programme search

• And some other functions

Tracing the same programme
automatically (Network-Tracking
Reception)

When driving in an area where FM reception is
not good, the tuner built in this unit automatically
tunes in to another RDS station, broadcasting
the same programme with stronger signals. So,
you can continue to listen to the same
programme in its finest reception, no matter
where you drive. (See the illustration on page

17.)

Two types of the RDS data are used to make
Network-Tracking Reception work correctly—PI
(Programme Identification) and AF (Alternative
Frequency).
Without receiving these data correctly from the
RDS station you are listening to, Network­Tracking Reception will not operate.

To use Network-Tracking Reception

You can select the different modes of network­tracking reception to continue listening to the
same programme in its finest reception.
When shipped from the factory, “AF” is selected.

• AF: Network-Tracking Reception is
activated with Regionalization set to
“off.”
With this setting, the unit switches to
another station within the same
network when the received signals
from the current station become
weak. (In this mode, the programme
may differ from the one currently
received.)
The AF indicator lights up but the
REG indicator does not.

• AF REG: Network-Tracking Reception is
activated with Regionalization set to
“on.”
With this setting, the unit switches to
another station, within the same
network, broadcasting the same
programme when the received
signals from the current station
become weak.
Both the AF and REG indicators light
up.

• OFF: Network-Tracking Reception is
deactivated.
Neither the AF indicator nor the REG
indicator lights up.

REG indicator

AF indicator

Note:

If a DAB tuner is connected and Alternative Reception
(for DAB services) is activated, Network-Tracking
Reception (“AF”) is also activated automatically. On
the other hand, Network-Tracking Reception cannot
be deactivated without deactivating Alternative
Reception. (See page 37.)

ENGLISH

11

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 24.)

ENGLISH

2

Select “AF-REG” (alternative
frequency/regionalization reception)
if not shown on the display.

3

Select the desired mode—“AF,”
“AF REG,” or “OFF.”

4

Finish the setting.

Using TA Standby Reception

TA Standby Reception allows the unit to switch
temporarily to Traffic Announcement (TA) from
the current source (another FM station, tape, or
other connected components).

• TA Standby Reception will not work if you are
listening to an AM station.

Press T TP/PTY to activate TA Standby
Reception.

7 When the current source is FM, the TP

indicator either lights up or flashes.

• If the TP indicator lights up, TA Standby

Reception is activated.
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically tunes in to
the station. The volume changes to the
preset TA volume level (see page 16) and the
traffic announcement can be heard.

• If the TP indicator flashes, TA Standby

Reception is not yet activated since the
station being received does not provide the
signals used for TA Standby Reception.
To activate TA Standby Reception, you need
to tune in to another station providing these
signals. Press ¢ or 4 to search
for such a station.
When a station providing these signals is
tuned in, the TP indicator stops flashing and
remains lit. Now TA Standby Reception is
activated.

12

7 When the current source is other than FM,

the TP indicator lights up.
If a station starts broadcasting a traffic
announcement, “TRAFFIC” appears on the
display, and this unit automatically changes the
source and tunes in to the station.

To deactivate the TA Standby Reception,

press T TP/PTY again. The TP indicator
disappears.

Using PTY Standby Reception

PTY Standby Reception allows the unit to switch
temporarily to your favorite programme (PTY:
Programme Type) from the current source
(another FM station, tape, or other connected
components).

• PTY Standby Reception will not work if you are
listening to an AM station.

You can select your favorite programme type for
PTY Standby Reception.
When shipped from the factory, PTY Standby
Reception is turned off. (“OFF” is selected for
PTY Standby Reception.)

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 24.)

2

Select “PTY STBY” (standby) if not
shown on the display.

7 When the current source is FM, the PTY

indicator either lights up or flashes.

• If the PTY indicator lights up, PTY Standby
Reception is activated.
If a station starts broadcasting the selected
PTY programme, this unit automatically
tunes in to the station.

• If the PTY indicator flashes, PTY Standby
Reception is not yet activated since the
station being received does not provide the
signals used for PTY Standby Reception.
To activate PTY Standby Reception, you
need to tune in to another station providing
these signals. Press ¢ or 4 to
search for such a station.
When a station providing these signals is
tuned in, the PTY indicator stops flashing
and remains lit. Now PTY Standby Reception
is activated.

7 When the current source is other than FM,

the PTY indicator lights up.
If a station starts broadcasting the selected
PTY programme, this unit automatically
changes the source and tunes in to the station.

To deactivate the PTY Standby Reception,

select “OFF” in step 3 on the left column. The
PTY indicator disappears.

ENGLISH

3

Select one of the twenty-nine PTY
codes. (See page 17.)

Selected code name
appears on the display
and is stored into
memory.

4

Finish the setting.

13

Searching your favorite programme

You can search any one of the PTY codes.
In addition, you can store your 6 favorite
programme types in the number buttons.

ENGLISH

When shipped from the factory, the following
6 programme types have been stored in the
number buttons (1 to 6).

To store your favorite programme types, see
below.

To search for your favorite programme type,

see page 15.

1

POP M

45

CLASSICS

To store your favorite programme types

1

Press and hold T TP/PTY for more
than 2 seconds while listening to an
FM station.

2

ROCK M EASY M

AFFAIRS

VARIED

2

Select one of the twenty-nine PTY
codes. (See page 17.)

Selected code name
appears on the display.

3

Press and hold the number button
for more than 2 seconds to store the
PTY code selected into the preset

3

6

number you want.

“MEMORY” and the selected code name will
appear alternately.

4

Press and hold T TP/PTY for more
than 2 seconds to exit from this
mode.

14

The last selected PTY code appears.

To search for your favorite programme type

1

Press and hold T TP/PTY for more
than 2 seconds while listening to an
FM station.

The last selected PTY code appears.

• If there is a station broadcasting a programme
of the same PTY code as you have selected,
that station is tuned in.

• If there is no station broadcasting a programme
of the same PTY code as you have selected,
the station will not change.

Note:

In some areas, the PTY search will not work correctly.

Other convenient RDS
functions and adjustments

ENGLISH

2

To select one of your favorite
programme type

or

To select any one of the twenty-nine
PTY-codes

Ex.: When “ROCK M” is selected

3

Press ¢ or 4 to start PTY
search for your favorite programme.

Automatic selection of the station
when using the number buttons

Usually when you press the number button, the
preset station is tuned in.
However, when the preset station is an RDS
station, something different will happen. If the
signals from that preset station are not sufficient
for good reception, this unit, using the AF data,
tunes in to another frequency broadcasting the
same programme as the original preset station is
broadcasting. (Programme search)

• The unit takes some time to tune in to another
station using programme search.

To activate programme search, follow the
procedure below.

• See also “Changing the general settings
(PSM)” on page 23.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select

“P(Programme)-SEARCH.”

3 Turn the control dial clockwise to select “ON.”

Now programme search is activated.

4 Press SEL (select) to finish the setting.

To cancel programme search, repeat the same

procedure and select “OFF” in step 3 by turning
the control dial counterclockwise.

15

Changing the display mode while
listening to an FM station

You can change the initial indication on the
display to station name (PS NAME), station

ENGLISH

frequency (FREQ), or clock time (CLOCK) while
listening to an FM RDS station.

• See also “Changing the general settings
(PSM)” on page 23.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select

“DISPMODE” (display mode).

3 Turn the control dial to set to the desired

indication (“PS NAME,” “FREQ,” or “CLOCK”).

4 Press SEL (select) to finish the setting.

Setting the TA volume level

You can preset the volume level for TA Standby
Reception. When a traffic programme is received,
the volume level automatically changes to the
preset level.

• See also “Changing the general settings
(PSM)” on page 23.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select “TA VO L”

(TA volume).

3 Turn the control dial to set to the desired

volume.
You can set it from “VOL 00” to “VOL 50.”

4 Press SEL (select) to finish the setting.

Note:

By pressing DISP (display), you can change the
display while listening to an FM RDS station.
Each time you press the button, the following
information appears on the display:

Station name

(PS NAME)

Station frequency

(FREQ)

Programme type

(PTY)

Clock

(CLOCK)

• Then, the display goes back to the original
indication in several seconds.

Automatic clock adjustment

When shipped from the factory, the clock built in
this unit is set to be readjusted automatically using
the CT (Clock Time) data in the RDS signal.
If you do not want to use automatic clock
adjustment, follow the procedure below.

• See also “Changing the general settings
(PSM)” on page 23.

1 Press and hold SEL (select) for more than

2 seconds so that one of the PSM items
appears on the display.

2 Press ¢ or 4 to select “AUTO

ADJ” (adjustment).

3 Turn the control dial counterclockwise to

select “OFF.”
Now automatic clock adjustment is canceled.

4 Press SEL (select) to finish the setting.

To reactivate clock adjustment, repeat the same

procedure and select “ON” in step 3 by turning the
control dial clockwise.

Note:

You must stay tuned to the same station for more than
2 minutes after setting “AUTO ADJ” to “ON.”
Otherwise, the clock time will not be adjusted. (This is
because the unit takes up to 2 minutes to capture the
CT data in the RDS signal.)

16

PTY codes

NEWS: News
AFFAIRS: Topical programmes expanding

on current news or affairs

INFO: Programmes which impart advice

on a wide variety of topics
SPORT: Sport events
EDUCATE: Educational programmes
DRAMA: Radio plays
CULTURE: Programmes on national or

regional culture
SCIENCE: Programmes on natural science

and technology
VARIED: Other programmes like comedies

or ceremonies
POP M: Pop music
ROCK M: Rock music
EASY M: Easy-listening music
LIGHT M: Light music
CLASSICS: Classical music
OTHER M: Other music
WEATHER: Weather information
FINANCE: Reports on commerce, trading,

the Stock Market, etc.
CHILDREN: Entertainment programmes for

children

SOCIAL: Programmes on social activities
RELIGION: Programmes dealing with any

aspect of belief or faith, or the
nature of existence or ethics

PHONE IN: Programmes where people can

express their views either by
phone or in a public forum

TRAVEL: Programmes about travel

destinations, package tours,
and travel ideas and
opportunities

LEISURE: Programmes concerned with

recreational activities such as

gardening, cooking, fishing, etc.
JAZZ: Jazz music
COUNTRY: Country music
NATION M: Current popular music from

another nation or region, in that

country’s language
OLDIES: Classic pop music
FOLK M: Folk music
DOCUMENT: Programmes dealing with

factual matters, presented in an

investigative style

ENGLISH

The same programme can be received on different frequencies.

Programme 1
broadcasting on
frequency A

Programme 1
broadcasting on
frequency B

Programme 1
broadcasting on
frequency C

Programme 1

broadcasting on

frequency E

Programme 1
broadcasting on
frequency D

17

ENGLISH

TAPE OPERATIONS

Listening to a cassette

You can play back type I (normal) tapes.

1

Open the control panel.

Note on One-Touch Operation:

When a cassette is already in the cassette
compartment, pressing TAPE CD-CH turns on
the unit and starts tape play automatically.

2

Insert a cassette into the cassette
compartment.

The unit turns on and
tape play starts
automatically.

3

Close the control panel by hand.

To stop play and eject the cassette

Press 0.
Tape play stops, the control panel flips down. The
cassette automatically ejects from the cassette
compartment. The source changes to the
previously selected one.
If you change the source, tape play also stops
(without ejecting the cassette this time).

• You can also eject the cassette by pressing 0

while the unit is turned off.

To fast-forward and rewind a tape

Press and hold ¢ for
more than one second to
fast-forward the tape.
When the tape reaches its
end, the tape is reversed
and playback starts from the
beginning of the other side.

Press and hold 4 for more than one
second to rewind the tape.
When the tape reaches its end, playback of the
same side starts.

To stop fast-forward and rewind at any
position on the tape, press 23.

Tape play starts from that position on the tape.

18

4

Select the tape direction.

Each time you press 23,
the tape direction alternates
between forward
( ) and reverse
( ).

Notes:

• When one side of the tape reaches its end during
play, the other side of the tape automatically starts
playing. (Auto Reverse)

• When the tape reaches its end while fast­forwarding, the tape direction will be changed
automatically.

Finding the beginning of a tune

Other convenient tape functions

Multi Music Scan (MMS) allows you to automatically
start playback from the beginning of a specified
tune. You can specify up to 9 tunes ahead of or
before the current tune.

During playback

Specify the tune you want to locate (how
many tunes ahead of or before the
current tune).

Press ¢ to locate a
tune ahead of the current
tune on the cassette.

Press 4 to locate a tune before the
current tune on the cassette.

Ex.: When you locate three tunes ahead of

the current tune

Each time you press the buttons, the number
changes up to ±9.
When the beginning of the specified tune is
located, playback starts automatically.

Notes:

• While locating a specified tune:
– If the tape is rewound to its beginning, playback

starts from the beginning of that side.

– If the tape is fast-forwarded to the end, it is

reversed and played from the beginning of the
other side.

• In the following cases, the Multi Music Scan

function may not operate correctly:

– Tapes with tunes having long pianissimo

passages (very quiet parts) or non-recorded

portions between tunes.
– Tapes with short non-recorded sections.
– Tapes with high level of noise or humming

between tunes.
– Tapes with tunes recorded at low recording

levels.

Skipping the blank portions on the tape

You can skip blank portions between the tunes
(Blank Skip).
When this function is turned on, the unit fast­forwards (skipping blank portions of 15 seconds
or more), to the next tune and starts playback.

• See also “Changing the general settings
(PSM)” on page 23.

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(PSM: see page 24.)

2

Press ¢ or 4 to select
“B.SKIP” (blank skip).

3

Turn the control dial clockwise to
select “ON.”

Now Blank Skip is
activated.

4

Finish the setting.

To cancel Blank Skip, repeat the same procedure

and select “OFF” in step 3 by turning the control
dial counterclockwise.

ENGLISH

19

Playing the current tune repeatedly

You can play the current tune repeatedly
(Repeat Play).

ENGLISH

When the tune has been played, the tape is
automatically rewound to the beginning of that
tune and the same tune will be played again.

To cancel Repeat Play, repeat steps 1 and 2
again so that the RPT indicator goes off.

Note:

In the following cases, Blank Skip and Repeat Play
may not operate correctly:
– Tapes with tunes having long pianissimo passages

(very quiet parts) or non-recorded portions during

tunes.
– Tapes with short non-recorded sections.
– Tapes with high level noise or humming between

tunes.
– Tapes with tunes recorded at low recording levels.

1 Press M MODE to enter the

functions mode while playing a
tune you want to hear over again
on a cassette.

2 Press RPT (repeat), while still in

the functions mode, so that
“REPEAT” appears on the
display.

RPT indicator

Prohibiting cassette ejection

You can prohibit cassette ejection and lock a
cassette in the cassette compartment.

While pressing TAPE CD-CH, press and
hold for more than 2 seconds.

“NO EJECT” flashes on the display for about
5 seconds, and the cassette is locked and cannot
be ejected.

To cancel the prohibition and unlock the
cassette

While pressing TAPE CD-CH, press and hold

again for more than 2 seconds.
“EJECT OK” flashes on the display for about
5 seconds, and the cassette is unlocked.

Note:

If you press 0 while cassette ejection is prohibited,
the control panel flips down, but the cassette
continues to play and cannot be ejected.

20

SOUND ADJUSTMENTS

Selecting preset sound modes
(C-EQ: custom equalizer)

You can select a preset sound mode (C-EQ:
custom equalizer) suitable to the music genre.

• There is a time limit in doing the following
procedure. If the setting is canceled before you
finish, start from step 1 again.

1

Press M MODE to enter the
functions mode.

2

Press EQ (equalizer), while still in
the functions mode.

The last selected sound mode
is recalled and applied to the
current source.

Ex.: If you have selected “USER” previously

Indication For: Preset values

BAS TRE LOUD
USER (Flat sound) 00 00 OFF
ROCK Rock or +03 +01 ON

disco music

CLASSIC Classical +01 –02 OFF

music
POPS Light music +04 +01 OFF
HIP HOP Funk or rap +02 00 ON

music
JAZZ Jazz music +02 +03 OFF

Note:

You can adjust each sound mode to your preference.
Once you make an adjustment, it is automatically
stored for the currently selected sound mode. See
“Adjusting the sound” on page 22.

ENGLISH

3

Select the sound mode you want.

Each time you press the
button, the sound modes
change as follows:

USER

The EQ indicator lights up when any sound
mode other than “USER” is selected.

Ex.: When you select “ROCK”

ROCK

CLASSIC

POPSHIP HOPJAZZ

21

Adjusting the sound

2

Adjust the setting.

You can adjust the sound characteristics to your
preference.

ENGLISH

1

Select the item you want to adjust.

Each time you press the
button, the adjustable items
change as follows:

BAS

(bass)

VOL

(volume)

Indication To do: Range

1

BAS*

TRE*

FAD *

BAL Adjust the left L06 (Left only)

LOUD*1Boost low and high

VOL*

1

*

When you adjust the bass, treble, or loudness, the
adjustment you have made is stored for the
currently selected sound mode (C-EQ) including
“USER.”

2

*

If you are using a two-speaker system, set the fader
level to “00.”

3

*

Normally the control dial works as the volume
control. So you do not have to select “VOL” to
adjust the volume level.

Adjust the bass. –06 (min.)

1

Adjust the treble. –06 (min.)

2

Adjust the front R06 (Rear only)
and rear speaker |
balance. F06 (Front only)

and right speaker |
balance. R06 (Right only)

frequencies to
produce a well­balanced sound
at low volume
level.

3

Adjust the volume. 00 (min.)

TRE

(treble)

LOUD

(loudness)

(balance)

|
+06 (max.)

|
+06 (max.)

LOUD ON
|
LOUD OFF

|
50 (max.)

FAD

(fader)

BAL

To increase the level or
turn on the loudness

To decrease the level or
turn off the loudness

Tone level indicator changes as
you adjust the bass or treble.

Ex. 1: When you adjust “TRE” (treble)

Ex. 2: When you turn on the loudness

3

Repeat steps 1 and 2 to adjust the
other items.

To reset each sound mode to the factory
settings, repeat the same procedure and

reassign the preset values listed in the table on
page 21.

22

OTHER MAIN FUNCTIONS

Changing the general settings
(PSM)

You can change the items listed in the table on
page 24 by using the PSM (Preferred Setting
Mode) control.

Basic Procedure

1

Press and hold SEL (select) for more
than 2 seconds so that one of the
PSM items appears on the display.
(See page 24.)

Ex.: If you have selected “CLOCK H”

previously

2

Select the PSM item you want to
adjust.

3

Adjust the PSM item selected.

Ex.: When you select “AUDIO 2”

4

Repeat steps 2 and 3 to adjust the
other PSM items if necessary.

5

Finish the setting.

ENGLISH

Ex.: When you select “LEVEL”

23

Preferred Setting Mode (PSM) items

• For detailed operations of each PSM items, refer to the pages listed in the table.

ENGLISH

Indications Selectable values/items

CLOCK H Hour adjustment

CLOCK M Minute adjustment

24H/12H 24/12-hour time display

AUTO ADJ Automatic clock setting

DISPMODE Display mode

CH DISP Changer display

AF-REG Alternative frequency/

Regionalization reception

PTY STBY PTY standby

TA VO L Traffic announcement

volume

P-SEARCH Programme search

DAB AF*2Alternative frequency

Factory-preset See

settings page

0 – 23 (1 – 12)

00 – 59

12H

24H 24H

0 (0:00)

00 (0:00)

OFF ON ON 16

PS NAME FREQ

CLOCK

PS NAME

TIME DISC DISC 25

AF

OFF

29 programme types

VOL 00 – VOL 50

AF REG

1

OFF*

(see page 17)

AF

OFF

VOL 20 16

OFF ON OFF 15

AF OFF AF ON AF ON 37

6

16

11, 12

13

DAB VOL*2DAB volume adjustment

LEVEL Level display

VOL –12 — VOL 12 VOL 00 37

AUDIO 2 OFF

AUDIO 1

TEL Telephone muting

OFF MUTING 1

MUTING 2

B.SKIP Blank skip

3

EXT IN*

1

*

Displayed only when the “DAB AF” is set to “AF OFF.”

2

*

Displayed only when the DAB tuner is connected.

3

*

Displayed only when one of the following sources is selected—FM, AM, and TAPE.

External component

OFF

CHANGER

24

AUDIO 2 25

OFF

25

ON OFF 19

LINE IN CHANGER 25

To set the changer display—CH DISP

This mode is used to check the display
information of the CD changer.
When shipped from the factory, “DISC” is
selected.

• DISC: Disc number and track number (or
folder number if the current playing disc
is an MP3 disc) appear.

• TIME: Elapsed playing time and track number
appear.

To select the external component to use
—EXT IN

You can connect the external component to the
CD changer jack on the rear using the Line Input
Adapter KS-U57 (not supplied).
To use the external component as the playback
source through this unit, you need to select
which component—CD changer or external
component—to use.
When shipped from the factory, CD changer is
selected as the external component.

ENGLISH

To select the level meter—LEVEL

You can select the level meter display according
to your preference.
When shipped from the factory, “AUDIO 2” is
selected.

• AUDIO 1: Shows the audio level indicator.

• AUDIO 2: Alternates “AUDIO 1” setting and

illumination display.

• OFF: Erases the audio level indicator.

To select the telephone muting—TEL

This mode is used when a cellular phone system
is connected. Depending on the phone system
used, select either “MUTING 1” or “MUTING 2”
whichever mutes the sounds from this unit.
When shipped from the factory, this mode is
deactivated.

• MUTING 1: Select this if this setting can mute

the sounds while using the cellular
phone.

• MUTING 2: Select this if this setting can mute

the sounds while using the cellular
phone.

• OFF: Cancels the telephone muting.

• CHANGER: To use the CD changer.

• LINE IN: To use the external component
other than CD changer.

Note:

For connecting the Line Input Adapter KS-U57 and
the external component, refer to the Installation/
Connection Manual (separate volume).

25

Changing the standard plate

This section is only for KS-T807.

You can change the standard plate with another

ENGLISH

plate supplied with your unit.
You can also download them by visiting
<http://www.jvc.co.jp/jvccar>.

• When changing the plate, be careful not to
leave your fingerprints on the plate or cover.

1

Loosen the screws with the supplied
hex screwdriver.

2

Remove the plate cover and the
standard plate.

Standard plate

3

Replace with another plate (a
standard, cutout, or downloaded
plate) of your preference.

• When attaching a standard plate

Standard plate

Plate cover

• When attaching a cutout or downloaded
plate

Add the transparent plate (supplied)
between the cutout or downloaded plate
and the plate cover in order to attach the
plate cover in place.

Cutout or
downloaded
plate

Plate cover

26

Plate cover

Transparent plate
(supplied)