JVC KS-AX5700, KS-AX5500 User Manual

KS-AX5700 KS-AX5500

POWER AMPLIFIER: INSTRUCTIONS AMPLIFICATEUR DE PUISSANCE: MANUEL D’INSTRUCTIONS

LVT1384-001A

[J/E/U]

0605MNMMDWASH

EN, FR

ENGLISH

Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

For safety....

•

Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

CAUTIONS AND NOTES

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems.

• This unit uses BTL (Balanced Trans-formerless) ampliﬁ er circuitry, i.e., ﬂ oating ground system, so please comply with the following:

Do not connect the “·” terminals of the speakers to each other. Do not connect the “·” terminals of the speakers to the metal body or chassis.

• Cover the unused terminals with insulating tape to prevent them from short circuiting.

•

When an extension lead is used, it should be as thick and short as possible; connect it ﬁ rmly with insulating tape.

• Be sure to leave an appropriate space between the antenna (aerial) and the wires of this unit.

•

When replacing the fuse, only use a 40 A fuse.

• Do not let pebbles, sand or metallic objects get inside the unit.

•

To keep the heat dissipation mechanism running effectively, wipe the accumulated dust off periodically.

• Listening to the tape, radio, CD or MD, etc. with the volume on loud for a long period of time will exhaust the battery, while the engine is turned off or while the engine is idling.

• This unit becomes very hot. Be careful not to touch the unit not only when using but for a while after using.

DO NOT disassemble the units since there are no user serviceable parts inside.

For Customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.

Model No.

Serial No.

TERMINAL CONNECTIONS

When making the terminal connections…

Properly ﬁ x the terminal with the screw provided by turning it in the direction as illustrated.

Note

When you tighten the screw, make sure that the screw is securely ﬁ xed in place to prevent disconnection of the terminal. Avoid over-tightening as it may cause damage to the screw or its head slot.

POWER SUPPLY

INSTALLATION

The following illustration shows a typical installation. However, you should make adjustments corresponding to your speciﬁ c car. If you have any questions or require information regarding installation kits, consult your “JVC IN-CAR ENTERTAINMENT” car audio dealer or a company supplying kits.

CAUTION

To prevent short circuits while making connections, keep the battery’s negative terminal disconnected.

• When using a power cord, be sure to place the 40 A fuse near the battery as shown.

• Connect the lead wire (purchased separately) through which power is supplied directly to the

battery’s “ª” terminal only after all the other connections have been made.

The lead wire connected to the + B terminal of this unit should have a cross-section of more than 8 mm

• If you have any questions regarding the thickness of the power cord, etc., consult your nearest “JVC IN-CAR ENTERTAINMENT” car audio dealer.

When you use JVC car receiver with a remote lead (a), connect to the REM terminal on this unit. When connecting a unit without a remote lead (b), connect to the accessory circuit of the car which is activated by the ignition switch. In this case, noise may occur when the car receiver is turned on or off. To avoid this noise, do not turn on or off the car receiver itself. You can turn on or off the car receiver along with the on/off operation of the ignition switch.

If the POWER/PROTECTOR lamp lights in red, it indicates incorrect speaker wiring or connections. In normal status, the POWER/PROTECTOR lamp lights in green. Make sure to correct speaker wiring and other connections.

. Be sure to use a ring terminal (optional) for secure connection.

A Mount on a ﬁ rm surface, such as in the trunk room or under the front seat.

• Since heat is generated in this unit, do not mount near inﬂ ammable objects. In addition, mount in an area that will not prevent the unit from dissipating heat.

• Do not mount the unit in the places subject to heat such as near a radiator, in a glove compartment or in insulated areas such as under a car mat that will prevent the unit from dissipating heat.

B When mounting this unit, be sure to use the screws provided. If any other screws are used,

there is a risk of loosening the unit or damaging parts inside it.

• Before drilling holes in the trunk to install the unit, make sure that there is a sufﬁ cient space under the trunk so that you do not drill holes in the fuel tank, etc.

C After install the unit, attach the terminal cover.

SPEAKER SYSTEMS

This ampliﬁ er provides two types of speaker connections: Normal mode and Bridge mode. You can choose either type of connections depending on the speakers conﬁ guration equipped on your car. Make sure to comply with the following notes:

• Be sure not to connect the “·” terminals of the speakers to a common point.

• If the ground wire is common to both left/right and front/rear speaker wirings, this unit cannot be used. Always use the independent lead wires for the speakers to be used. In this case, redo the wirings.

• Use the speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge mode).

• Use the speakers which have sufﬁ cient power to the unit.

SPEAKER CONNECTIONS

Connection varies depending on the number of the speakers used in your car. Select the appropiate connection referring to the diagrams below.

Before connecting: Securely connect all the parts. If the connections are loose, due to contact resistance etc., heat will break out and may cause an accident. Secure and cover the cords with insulating tape and run them under the car mats.

• Depending on the manufacturer and model of the car, speaker wiring may have been ﬁ nished when purchased. If the ground wire is common to both left and right speakers, this unit cannot be used. In this case, redo the speaker wiring.

å When your receiver is equipped with Line Output, connect the Line Output (through the

receiver) to the INPUT jacks on this unit.

∫ When your receiver is NOT equipped with Line Output, connect the speaker connector

(through the receiver) to the HIGH INPUT terminal on this unit.

KS-AX5500

4-speaker system

KS-AX5700

2-speaker system

2-speaker system plus subwoofer—BRIDGE MODE*

Subwoofer system—BRIDGE MODE*

2-speaker system (2 ampliﬁ ers)—BRIDGE MODE*

2-speaker system—BRIDGE MODE

Not supplied for this unit.

BRIDGE MODE: Be sure to connect the line output from the receiver to the left (L) jack on this

unit.

Be sure to connect the both leads to the target speaker lead.

+ 4 hidden pages