JVC KD-7402 User Manual

DVD/CD RECEIVER

DVD-/CD-RECEIVER RÉCEPTEUR DVD/CD DVD/CD-RECEIVER

KD-DV7402/KD-DV7401

For canceling the display demonstration, see page 7. Zum Abbrechen der Displaydemonstration siehe Seite 7. Pour annuler la démonstration des affichages, référez-vous à la page 7. Zie bladzijde 7 voor het annuleren van de displaydemonstratie.

ENGLISHDEUTSCH

FRANÇAIS

NEDERLANDS

For installation and connections, refer to the separate manual. Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch. Pour l’installation et les raccordements, se référer au manuel séparé. Bijzonderheden over de installatie en aansluiting van het apparaat vindt u in de desbetreffende handleiding.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

GET0534-001A

[E]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

ENGLISH

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Caution on volume setting:

This symbol is only valid in the European Union.

Information for Users on Disposal of Old Equipment

This symbol indicates that the product with this symbol should not be disposed as general household waste at its end-of-life. If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country and municipality. By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health.

This unit is equipped with the steering wheel remote control function.

• See the Installation/Connection Manual (separate volume) for connection.

Digital devices (CD/USB) produce very little noise compared with other sources. Lower the volume before playing these digital sources to avoid damaging the speakers by sudden increase of the output level.

Caution for DualDisc playback

The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

Caution:

If the temperature inside the car is below 0°C, the movement of animation and text scroll will be halted on the display to prevent the display from being blurred. appears on the display. When the temperature increases, and the operating temperature is resumed, these functions will start working again.

How to reset your unit

• Your preset adjustments will also be erased (except the registered Bluetooth device, see pages 28 and 29).

How to forcibly eject a disc

“Please Eject” appears on the display.

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

WARNINGS: (To prevent accidents and damage)

• DO NOT install any unit or wire any cable in a location where;

– it may obstruct the steering wheel and

gearshift lever operations.

– it may obstruct the operation of safety

devices such as air bags.

– it may obstruct visibility.

• DO NOT operate the unit while driving.

• If you need to operate the unit while driving, be sure to look around carefully.

• The driver must not watch the monitor while driving.

If the parking brake is not engaged,

“DRIVER MUST NOT WATCH THE MONITOR WHILE DRIVING.” appears on the monitor, and no playback picture will be shown.

– This warning appears only when the

parking brake lead is connected to the parking brake system built in the car (refer to the Installation/Connection Manual).

For security reasons, a numbered ID card is provided with this unit, and the same ID number is imprinted on the unit’s chassis. Keep the card in a safe place, as it will help the authorities to identify your unit if stolen.

For safety...

• Do not raise the volume level too much, as this will

block outside sounds, making driving dangerous.

• Stop the car before performing any complicated

operations.

ENGLISH

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

How to use the M MODE and SEL

buttons

If you use M MODE or SEL (select), the display and some controls (such as the number buttons,

4 /¢ buttons, 5/∞ buttons, and the

ENGLISH

control dial) enter the corresponding control mode.

Ex.: When you press number button 1 after pressing

M MODE, to operate the FM tuner.

Detaching the control panel

Avoid touching the connectors.

To use these controls for original functions, press M MODE again.

• However, pressing SEL makes the unit enters a different mode.

• Waiting for about 15 seconds (or 30 seconds for Bluetooth sources) without pressing any of these buttons will automatically cancels the control.

Indication language:

In this manual, English indications are used for purposes of explanation. You can select the indication language on the monitor on the “LANGUAGE” setting (see page 50).

Attaching the control panel

Opening and closing the control

panel

Open...

Close...

CONTENTS

INTRODUCTIONS

Playable disc type ........................................................................................................................... 6

Preparation ..................................................................................................................................... 7

OPERATIONS

Basic operations .............................................................................................................................. 8

• Using the control panel ............................................................................................................................ 8

• Using the remote controller (RM-RK252) ................................................................................................. 9

Listening to the radio ...................................................................................................................... 12

Disc operations ................................................................................................................................ 16

• Operations using the control panel .......................................................................................................... 17

• Operations using the remote controller (RM-RK252) ............................................................................... 20

Listening to the USB device ............................................................................................................. 26

Dual Zone operations ...................................................................................................................... 27

EXTERNAL DEVICES

Listening to the Bluetooth® devices ................................................................................................ 28

• Using the Bluetooth cellular phone ......................................................................................................... 30

• Using the Bluetooth audio player ............................................................................................................ 32

Listening to the CD changer ............................................................................................................ 33

Listening to the DAB tuner .............................................................................................................. 34

Listening to the iPod ....................................................................................................................... 37

• When connecting with the USB cable ...................................................................................................... 37

• Operations using the control screen ......................................................................................................... 38

• When connecting with the interface adapter .......................................................................................... 40

• Selecting the playback modes ................................................................................................................. 40

Listening to the other external components ................................................................................... 41

ENGLISH

SETTINGS

Selecting a preset sound mode ....................................................................................................... 43

General settings — PSM ................................................................................................................ 45

Disc setup menu .............................................................................................................................. 50

Bluetooth settings .......................................................................................................................... 52

REFERENCES

Maintenance ................................................................................................................................... 53

More about this unit ....................................................................................................................... 54

Troubleshooting .............................................................................................................................. 61

Specifications .................................................................................................................................. 66

Playable disc type

Disc type Recording format, file type, etc Playable

DVD DVD Video (Region Code: 2) *

ENGLISH

DVD Audio

DVD-ROM

DVD Recordable/Rewritable (DVD-R/-RW *

, +R/+RW *3)

• DVD Video: UDF bridge

• DVD-VR

• DivX/MPEG-1/MPEG-2/MP3/ WMA/WAV: ISO 9660 level 1, level 2, Romeo, Joliet

DVD Video

DVD-VR

DivX/MPEG1/MPEG2

MP3/WMA/WAV

AAC

JPEG/MPEG4

DVD+VR

DVD-RAM

Dual Disc DVD side

Non-DVD side

CD/VCD Audio CD/CD Text (CD-DA)/DTS-CD *

VCD (Video CD)

SVCD (Super Video CD)

CD-ROM

CD-I (CD-I Ready)

CD Recordable/Rewritable (CD-R/-RW)

• ISO 9660 level 1, level 2, Romeo, Joliet

CD-DA

DivX/MPEG1/MPEG2

MP3/WMA/WAV

AAC

JPEG/MPEG4

If you insert a DVD Video disc of an incorrect Region Code, “REGION CODE ERROR” appears on the monitor.

* *2 DVD-R recorded in multi-border format is also playable (except for dual layer discs). DVD-RW dual layer discs are not

playable.

*3 It is possible to play back finalized +R/+RW (Video format only) discs. +RW double layer discs are not playable. *4 To reproduce DTS sound, use the DIGITAL OUT terminal (see also pages 51 and 59).

Preparation

Cancel the display demonstration and set the clock

• See also pages 45 and 46.

1 2

Turn on the power.

Enter the PSM settings.

ENGLISH

Changing the display information and pattern

• When the power is turned off: Check the current clock time

Ex.: When tuner is selected as the source

Source operation display Audio level meter display

Cancel the display demonstrations

Select “Demo,” then “Off.”

Set the clock

Select “Clock Hr” (hour), then adjust the hour. Select “Clock Min” (minute), then adjust the minute. Select “24H/12H,” then “24Hours” or “12Hours.”

Finish the procedure.

(see “LevelMeter” on page 45)

7INTRODUCTIONS

Basic operations

Using the control panel

ENGLISH

1 • DAB: Select DAB service.

• DISC/USB/CD-CH: Select title/program/ playlist/folder.

• USB-iPod: Enter the main menu [Hold].

• iPod: Enter the main menu/Pause playback/ Confirm selection.

• BT-PHONE/BT-AUDIO: Select a registered device.

2 • Turn on the power.

• Turn off the power [Hold].

• Attenuate the sound (if the power is on).

3 Display window 4 USB (Universal Serial Bus) input jack 5 • Activate/deactivate TA Standby Reception.

• Enter programme type searching mode [Hold].

6 Flip down the control panel.

• To eject the disc, flip down the control panel then press 0 on the unit.

7 AV-IN (video) input jack 8 • TUNER: Search for station.

• DAB: Search for DAB ensemble.

• DISC/USB/USB-iPod/CD-CH/iPod: Select chapter/track.

• BT-AUDIO: Reverse skip/forward skip.

9 • Volume control [Turn].

• Select the source [Press] *1. TUNER = DAB *2 = DISC *2 = USB *2 (or

USB-iPod) *2 = CD-CH *2/iPod *2 (or EXT IN)

= BT-PHONE * = AV IN = (back to the beginning)

p • Select/adjust the sound mode.

= BT-AUDIO *2 = LINE IN

• Enter the PSM settings [Hold].

q • TUNER/DAB: Select preset station/DAB service.

• DISC/USB/CD-CH: Select chapter/title/ program/folder/track/disc (for CD changer).

• BT-PHONE: Dial preset phone number *3.

w • Enter functions mode.

• BT-PHONE: Activate Voice Dialing [Hold].

e Change the display information and pattern. r • TUNER/DAB: Select the bands.

• DISC/USB/USB-iPod: Start/pause playback.

• BT-AUDIO: Start/pause playback.

*1 Holding SOURCE will enter Bluetooth menu if a

Bluetooth phone is connected.

*2 You cannot select these sources if they are not ready

or not connected.

*3 For storing preset phone number, see page 32.

Using the remote controller (RM-RK252)

Installing the battery

R03/LR03/AAA

Insert the batteries into the remote controller by matching the polarity (+ and –) correctly.

Caution:

Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

If the effectiveness of the remote controller decreases, replace both batteries.

Before using the remote controller:

• Aim the remote controller directly at the remote sensor on the unit.

• DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting).

ENGLISH

Remote sensor

IMPORTANT:

If Dual Zone is activated (see page 27), the remote controller only functions for operating the DVD/CD player.

button

• Turns the power on if pressed briefly or attenuates the sound when the power is on.

• Turns the power off if pressed and held.

Continued on the next page

9OPERATIONS

2 5/∞ buttons

• TUNER/DAB: Selects the preset stations/ services.

• DISC:

– DVD-Video: Selects the title. – DVD-VR: Selects the program/playlist.

ENGLISH

– DivX/MPEG Video/MP3/WMA/WAV: Selects

the folders if included.

• USB:

– DivX/MPEG Video/MP3/WMA/WAV: Selects

the folders if included.

• CD-CH: Selects the folders if included.

• iPod:

5 : Enters the main menu (then 5 / ∞ /

–

4 / ¢ work as menu

selecting buttons.) 5 : Returns to the previous menu. ∞ : Confirms the selection. – ∞ : Pauses or resumes playback.

4 / ¢ buttons

• TUNER: – Searches for stations automatically if pressed

briefly.

– Searches for stations manually if pressed and

held.

• DAB: – Select ensembles if pressed briefly. – Searches for ensembles if pressed and held.

• DISC/USB/USB-iPod/CD-CH: – Reverse skip/forward skip if pressed briefly. – Reverse search/forward search if pressed and

held.

• BT-AUDIO: Reverse skip/forward skip if pressed

briefly.

• iPod: – Reverse skip/forward skip if pressed briefly. – Reverse search/forward search if pressed and

held. In menu selecting mode: – Selects an item if pressed briefly. (Then, press

∞ to confirm the selection.)

– Skips 10 items at a time if pressed and held.

3 VOL (volume) + / – buttons

• Adjusts the volume level.

2nd VOL (volume) buttons

• Adjust the volume level through the 2nd AUDIO OUT plug when pressed with SHIFT button (see page 27).

4 *

ASPECT button

• Not applicable for this unit.

PHONE button

• Answer incoming calls.

• Enters “Redial” menu when a Bluetooth phone is connected [Hold].

6 *

SETUP button

• Enters disc setup menu (during stop).

7 *

TOP M (menu) button

• DVD-Video/DivX: Shows the disc menu.

• DVD-VR: Shows the Original Program screen.

• VCD: Resumes PBC playback.

• USB-iPod: Enters the search mode menu (see page 39).

8 *

OSD (on-screen display) button

• Shows the on-screen bar.

9 SHIFT button

• Functions with other buttons.

p DISP (display) button

• Changes the display information.

q 1 / ¡ buttons

• DVD-Video: Slow motion playback (during pause).

• DVD-VR/VCD: Forward slow motion playback (during pause).

• DISC/USB/USB-iPod: Reverse search/forward search.

SOURCE button

• Selects the source.

e 3 (play) / 8 (pause) button

• DISC/USB/USB-iPod/BT-AUDIO: Starts/ pauses playback.

r (end call) button

• Ends the call.

BAND /

7 (stop) buttons

• TUNER/DAB: Selects the bands.

• DISC/USB/USB-iPod/BT-AUDIO: Stops playback.

t *

RETURN button

• VCD: Returns to the PBC menu.

• USB-iPod: Returns to Control Screen.

y *

MENU button

• DVD-Video/DivX: Shows the disc menu.

• DVD-VR: Shows the Playlist screen.

• VCD: Resumes PBC playback.

• USB-iPod: Enters the search mode menu (see page 39).

u *

% / ﬁ buttons

• DVD-Video: Makes selection/settings.

• CD-CH: Changes discs in the magazine.

@ / # buttons

• DVD-Video: Makes selection/settings.

• DivX/MPEG Video: Skips back or forward by about five minutes.

DIRECT button

• DISC/USB: Enters direct search mode for chapter/title/program/playlist/folder/track when pressed with SHIFT button (see page 20 for details).

CLR (clear) button

• DISC/USB: Erases the misentry when pressed with SHIFT button.

When Dual Zone is activated, these buttons cannot be

used.

*2 Functions as number buttons/* (asterisk)/# (hash)

when pressed with SHIFT button.

– TUNER/DAB: Selects the preset stations/services

(1 – 6).

– DISC: Enters chapter/title/program/playlist/folder/

track number after entering search mode by pressing SHIFT and DIRECT (see page 20 for details).

ENGLISH

ENT (enter) button

• Confirms selection.

i *

DUAL button

• Activates or deactivates Dual Zone.

o SURROUND button

• Not applicable for this unit.

11OPERATIONS

Listening to the radio

ENGLISH

Select “TUNER.”

Select the bands.

Search for a station to listen—Auto Search.

Manual Search: Hold either one of the buttons until “M” lights up on the display, then press it repeatedly.

• When receiving an FM stereo broadcast with sufficient signal strength, lights up on the display.

When an FM stereo broadcast is

hard to receive

Reception improves, but stereo effect will be lost.

• lights up on the display.

3 Exit from the setting.

FM station automatic presetting

— SSM (Strong-station Sequential Memory)

You can preset up to six stations for each band.

1 While listening to a station...

Local FM stations with the strongest signals are

searched and stored automatically in the selected FM band.

Manual presetting

Ex.: Storing FM station of 92.5 MHz into preset number

4 of the FM1 band.

Using the number buttons

Preset number flashes for a while.

Using the Preset Station list

• When is shown on the display, you can move back to the previous screen by pressing number button 3.

1 Follow steps 1 and 2 of “Using the number

buttons” on page 12.

• By holding 5 / ∞, the Preset Station List will

also appear (go to step 4).

Display the Preset Station List.

4 Select the preset number you want to store

into.

Listening to the preset station on

the Preset Station List

1 Display the Preset Station List, then select

the preset station you want to listen to.

ENGLISH

2 Change to the selected station.

The following features are available only for FM RDS stations.

Searching for FM RDS programme

— PTY Search

You can tune in to a station broadcasting your favorite programme by searching for a PTY code.

• When appears on the display, you can move back to the previous display by pressing number button 3.

• When / appears on the display, you can move to the other lists by pressing number button 5 or 6 repeatedly.

2 Select “Search.”

• You can move to the lists of the other FM bands by pressing number button 5 ( ) or 6 ( ) repeatedly.

5 Store the station.

The six preset PTY codes appears on the display.

Continued on the next page

13OPERATIONS

3 Select a PTY code.

You can select a PTY code from the

29 preset PTY codes or from the six stored PTY codes.

ENGLISH

• To store your favorite programme types, see the following.

4 Start searching for your favorite programme.

4 Select one of the PTY codes.

5 Store the selected PTY code.

If there is a station broadcasting a programme

of the same PTY code as you have selected, that station is tuned in.

Storing your favorite programme types

You can store six favorite programme types.

• When appears on the display, you can move back to the previous display by pressing number button 3.

2 Select “Memory.”

3 Select a preset number (“Preset1”–

“Preset6”) you want to store into.

Ex.: When “Classics” is selected in step 4

6 Repeat steps 3 to 5 to store other PTY codes

into other preset numbers.

7 Exit from the setting.

Activating TA/PTY Standby

Reception

TA Standby Reception

either lights up or flashes on the display.

• If lights up, the unit temporarily will switch to Traffic Announcement (TA), if available, from any source other than AM.

The volume changes to the preset TA volume level if

the current level is lower than the preset level (see page 47).

• If flashes, TA Standby reception is not yet activated. Tune in to another station providing the RDS signals.

To deactivate TA Standby Reception, press TP again. goes off.

PTY Standby Reception

Tracing the same programme—

Network-Tracking Reception

When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM RDS station of the same network, possibly broadcasting the same programme with stronger signals (see the illustration below).

ENGLISH

Select a PTY code.

4 Exit from the setting.

either lights up or flashes on the display.

• If lights up, the unit temporarily will switch to your favorite PTY programme from any source other than AM.

• If

flashes, PTY Standby reception is not yet activated. Tune in to another station (or service) providing the RDS signals.

To deactivate PTY Standby Reception, select “Off” in step 2. goes off.

• When a DAB tuner is connected, TA/PTY Standby Reception also searches for services. (See also page 35.)

• The unit will not switch to Traffic Announcement or PTY programme when a call connection is established through the “BT-PHONE.”

Available PTY codes

News, Affairs, Info, Sport, Educate, Drama, Culture, Science, Varied, Pop M (music), Rock M (music), Easy M (music), Light M (music), Classics, Other M (music), Weather, Finance, Children, Social, Religion, Phone In, Travel, Leisure, Jazz, Country, Nation M (music), Oldies, Folk M (music), Document

Programme A broadcasting on different frequency areas (01 – 05)

When shipped from the factory, Network-Tracking Reception is activated.

To change the Network-Tracking Reception setting, see “AF-Regn’l” on page 47.

• When the DAB tuner is connected, refer to “Tracing the same programme—Alternative Frequency Reception (DAB AF)” on page 36.

Automatic station selection—

Programme Search

Usually when you press the number buttons, the preset station is tuned in. If the signals from the FM RDS preset station are not sufficient for good reception, this unit, using the AF data, tunes in to another frequency broadcasting the same programme as the original preset station is broadcasting.

• The unit takes some time to tune in to another station using programme search.

• See also page 47.

15OPERATIONS

Disc operations

Before performing any operations...

Turn on the monitor to watch the playback picture. If you turn on the monitor, you can also control playback of other discs by referring to the monitor screen. (See pages 22 – 25.)

ENGLISH

The disc type is automatically detected, and playback starts automatically (for DVD: automatic start depends on its internal program). If the current disc does not have any disc menu, all tracks will be played repeatedly until you change the source or eject the disc.

” appears on the monitor when pressing a button, the unit cannot accept the operation you have tried to

If “ do.

• In some cases, without showing “ ,” operations will not be accepted.

To stop play and eject the disc

• Press SOURCE to listen to another playback source.

Open the control panel.

Make sure to detach the USB device before opening the control panel, as it might block the opening mechanism.

• To detach the USB device, see page 26.

Insert the disc.

Playback starts automatically.

Start playback if necessary.

Prohibiting disc ejection

To cancel the prohibition, repeat the same

procedure.

Operations using the control panel

Pressing (or holding) the following buttons allows you to...

Disc type

[Press] Select chapter [Hold] Reverse/fast-forward

chapter *

[Press] Select chapter [Hold] Reverse/fast-forward

chapter *

[Press] Select track [Hold] Reverse/fast-forward track *

Search speed:

*2 Search speed: *3 Press to select number 1 to 6; hold to select number 7 to 12.

Select title During stop: Locate title

Select program number/ playlist number

Select folder Locate particular folder directly

—

(Number buttons) *

During play/pause: Locate chapter

During stop: Locate program During play/pause: Locate chapter

Locate particular track directly (PBC not in use)

Locate particular track directly

ENGLISH

Continued on the next page

17OPERATIONS

After pressing M MODE, press the following buttons to...

Disc type

ENGLISH

• You can also cancel the playback mode by selecting “Off” or press number button 4 (

Skip 10 chapters (during play or pause)

Skip 10 tracks (within the same folder)

Skip 10 tracks (PBC not in use)

Skip 10 tracks (within the same folder)

Skip 10 tracks Repeat Track:

Repeat Chapter: Repeat current chapter Repeat Title: Repeat current title

Repeat Chapter: Repeat current chapter Repeat Program: Repeat current program (not

available for Playlist Playback)

Repeat Track: Repeat current track Repeat Folder: Repeat current folder

Repeat Track: Repeat current track (PBC not in

use)

Repeat Track: Repeat current track Repeat Folder: Repeat current folder

Repeat current track

—

Random Folder: Randomly play all tracks of

current folder, then tracks of

next folders Random All: Randomly play all tracks

Random All: Randomly play all tracks (PBC

not in use)

Random Folder: Randomly play all tracks of

current folder, then tracks of

next folders Random All: Randomly play all tracks

Random All: Randomly play all tracks

Selecting a folder/track on the list

(only for MP3/WMA/WAV file)

• When is shown on the display, you can move back to the previous screen by pressing number button 3.

Select “LIST.”

3 Select the list type.

4 Select an item.

Ex.: When “File” is selected in step 3

• You can move to the other lists by pressing

number button 5 ( ) or 6 ( ) repeatedly.

5 Change to the selected item.

A If File List is selected

The list disappears and playback starts.

B If Folder List is selected

• If the current folder is selected, File List

appears, then repeat steps 4 and 5 A to start playback.

• If another folder is selected, playback starts from the 1st file of the selected folder.

ENGLISH

19OPERATIONS

Operations using the remote controller (RM-RK252)

Disc

Button

ENGLISH

Stop play Stop play

Start play/Pause (if pressed during play) Start play/Pause (if pressed during play)

• Reverse/forward chapter search *1 (No sound can be heard.)

• Slow motion *2 during pause (No sound can be heard.)

* DVD-VR: Reverse slow motion does not work.

[Press] Select chapter (during play or pause) [Hold] Reverse/fast-forward chapter search *

• DVD-Video: Select title (during play or

• DVD-VR: Select playlist/program (during

pause)

play or pause)

—

Reverse/forward track search *4 (No sound can be heard.)

[Press] Select track (during play or pause)

[Hold] Reverse/fast-forward track search *

(No sound can be heard.)

Select folder

• Skip back or forward the scenes by about five minutes

• Select chapter

To search for chapter/title/program/playlist/folder/track directly (DVD/DivX/MPEG Video/VCD/ MP3/WMA/WAV/CD)

1 While holding SHIFT, press DIRECT repeatedly to select the desired search mode.

DVD-Video :

DVD-VR : CD :

DivX/MPEG Video :

MP3/WMA/WAV :

2 While holding SHIFT, press the number buttons (0 – 9) to enter the desired number. 3 Press ENT (enter) to confirm.

VCD :

Stop play Stop play Stop play

ENGLISH

Start play/Pause (if pressed during play)

Reverse/forward track search *

Start play/Pause (if pressed during play)

Reverse/forward track search *

Start play/Pause (if pressed during play)

Reverse/forward track search *

• Forward slow motion *2 during pause. (No sound can be heard.)

* Reverse slow motion does not work.

[Press] Select track (during play or

pause)

[Hold] Reverse/fast-forward track

search *3 (No sound can be

[Press] Select track (during play or

pause)

[Hold] Reverse/fast-forward track

search *

[Press] Select track (during play or

[Hold] Reverse/fast-forward track

heard.)

Select folder

—

———

• For DivX/MPEG Video/MP3/WMA/WAV, track is searched within the same folder.

• To erase a misentry, press CLR (clear) while holding SHIFT.

• To return to the previous screen, press RETURN.

*1 Search speed: *2 Slow motion speed: *3 Search speed: *4 Search speed: *5 Search speed:

pause)

search *

—

Continued on the next page

21OPERATIONS

Using menu driven features... (DVD-Video/ DVD-VR)

1 Press TOP M/MENU to enter the menu screen. 2 Press % / ﬁ / @ * / # * to select an item you want

to start play.

ENGLISH

3 Press ENT (enter) to confirm.

* Not applicable for DVD-VR.

Canceling the PBC playback... (VCD)

1 During stop, press DIRECT while holding SHIFT. 2 Hold SHIFT, then press the number buttons (0 – 9)

to enter the desired number.

3 Press ENT (enter) to confirm.

• To resume PBC, press TOP M/MENU.

Operations using the

on-screen bar

(DVD/DVD-VR/DivX/MPEG Video/VCD)

These operations are possible on the monitor using the remote controller.

1 Show the on-screen bar (see page 23).

(twice)

2 Select an item.

3 Make a selection.

If pop-up menu appears...

• To cancel pop-up menu, press RETURN.

• For entering time/numbers, see the following.

Entering time/numbers

Press % / ﬁ to change the number, then press @ / # to move to the next entry.

• Each time you press % / ﬁ, the number increases/ decreases by one value.

• After entering the numbers, press ENT (enter).

• It is not required to enter the zero and tailing zeros (the last two digits in the example below).

Ex.: Time search DVD: _:_ _:_ _ (Ex.: 1:02:00) Press % once, then # twice to go to the third entry, % twice, then press ENT (enter).

To remove the on-screen bar

On-screen bar

Ex.: DVD-Video

Information

Operation

1 Disc type 2 • DVD-Video/DTS-CD: Audio signal format type

and channel

• VCD: PBC

3 Playback mode *

DVD-Video: T. RPT: Title repeat C. RPT: Chapter repeat DVD-VR: C. RPT: Chapter repeat PG. RPT: Program repeat DivX/MPEG Video: T. RPT: Track repeat F. RPT: Folder repeat F. RND: Folder random A. RND: All random VCD *2: T. RPT: Track repeat A. RND: All random

4 Playback information

Current title/chapter Current program/chapter

Current playlist/chapter

Current track

Current folder/track

5 Time indication

Elapsed playing time of the disc

(For DVD-Video, elapsed playing time of the current title/program/ playlist.)

DVD-Video/DVD-VR: Remaining

title/program/playlist time VCD: Remaining disc time Elapsed playing time of the current

chapter/track *

Remaining time of the current

chapter/track *

6 Playback status

Play Forward/reverse search Forward/reverse slow-motion Pause Stop

7 Operation icons

Change time indication (see 5) Time Search (Enter the elapsed playing

time of the current title/program/

playlist or of the disc.) Title Search (by its number) Chapter Search (by its number) Track Search (by its number) Change the audio language or audio

channel Change or turn off the subtitle

language Change the view angle Repeat play * Random play *

*1 For repeat play/random play, see also page 18. *2 While PBC is not in use. *3 Not applicable for DVD-VR.

ENGLISH

23OPERATIONS

Operations using the control

screen

(DivX/MPEG Video/MP3/WMA/WAV/CD)

These operations are possible on the monitor using the remote controller.

ENGLISH

1 Show the control screen.

DivX/MPEG Video: Press MP3/WMA/WAV/CD: Automatically appear during

play.

2 Select “Folder” column or “Track” column

(except for CD).

3 Select a folder or track.

7 during play.

7 Track information 8 Track list with the current track selected

To select a playback mode

1 While control screen is displayed...

Playback mode selection screen appears on the

folder list section of the control screen.

2 Select a playback mode.

3 Select an item.

REPEAT:

RANDOM:

4 Start playback.

DivX/MPEG Video: Press ENT (enter) or 3/8. MP3/WMA/WAV/CD: Playback starts automatically.

Control screen

Ex.: MP3/WMA/WAV disc

1 Current folder number/total folder number 2 Folder list with the current folder selected 3 Selected playback mode 4 Elapsed playing time of the current track 5 Operation mode icon ( 3, 7, 8, ¡, 1 ) 6 Current track number/total number of tracks in the

current folder (total number of tracks on the disc)

Mode Playback functions

F. RPT

(folder repeat):

T. RPT

(track repeat):

A. RND

(all random):

F. RND

(folder random):

4 Confirm the selection.

* Not selectable for CD.

Repeat current folder

Repeat current track

Randomly play all tracks

Randomly play all tracks of current folder, then tracks of next folders

Operations using the list

screen

(DVD-VR/DivX/MPEG Video/MP3/WMA/WAV)

These operations are possible on the monitor using the remote controller.

List screen (DivX/MPEG Video/MP3/WMA/ WAV)

Before playing, you can display the folder list/track list to confirm the contents and start playing a track.

1 Display the folder list while stop.

2 Select an item from the folder list.

• Track list of the selected folder appears.

• To go back to the folder list, press RETURN.

3 Select a track to start playing.

• MP3/WMA/WAV: Control screen appears (see page 24).

Ex.: Folder list

1 Current folder number/total folder number 2 Current track number/total number of tracks in the

current folder

3 Current page/total number of the pages included

in the list

4 Current folder/track (highlighted bar)

List screen (DVD-VR)

You can use ORIGINAL PROGRAM or PLAY LIST screen anytime while playing DVD-VR with its data recorded.

1 Select a list screen.

1 Program/playlist number 2 Recording date 3 Recording source (TV station, the input

terminal of the recording equipment, etc.)

4 Start time of recording 5 Title of the program/playlist * 6 Current selection (highlighted bar) 7 Creating date of playlist 8 Number of chapters 9 Playback time

* The title of the original program or playlist may

not be displayed depending on the recording equipment.

2 Select an item from the list.

ENGLISH

25OPERATIONS

Listening to the USB device

You can connect a USB mass storage class device such as a USB memory, portable HDD, etc. to the unit.

• You can also connect an Apple iPod to the USB input jack. For details of the operations, see pages 37 – 41.

This unit can play DivX/MPEG Video/MP3/WMA/WAV tracks stored in a USB device.

ENGLISH

All tracks will be played repeatedly until you change the source or detach the USB device.

USB input jack

USB memory

Turn on the monitor to watch the playback picture if you play back a DivX/MPEG file. You can also control playback by referring to the monitor screen. (See also pages 22 – 25.)

• See pages 20 – 25 for operation using the remote controller.

• See pages 50, 51, and 56 for more settings.

If “ ” appears on the monitor when pressing a button, the unit cannot accept the operation you have tried to do.

• In some cases, without showing “ ,” operations will not be accepted.

If a USB device has been attached...

Playback starts from where it has been stopped previously.

• If a different USB device is currently attached, playback starts from the beginning.

To stop play and detach the USB device

Straightly pull it out from the unit.

• Press SOURCE to listen to another playback source.

You can operate the USB device in the same way you operate the files on a disc. (See pages 16 – 25.)

• You cannot select “USB” when Dual Zone is in use (see page 27).

Cautions:

• Avoid using the USB device if it might hinder your safety driving.

• Do not pull out and attach the USB device repeatedly while “Reading” is shown on the display.

• Do not start the car engine if a USB device is connected.

• This unit may not be able to play the files depending on the type of USB device.

• Operation and power supply may not work as intended for some USB devices.

• You cannot connect a computer to the USB input terminal of the unit.

• Make sure all important data has been backed up to avoid losing the data.

• Do not leave a USB device in the car, expose to direct sunlight, or high temperature to avoid deformation or cause damages to the device.

• Some USB devices may not work immediately after you turn on the power.

• For more details about USB operations, see page 56.

Dual Zone operations

You can enjoy disc playback on the external monitor connected to the VIDEO output terminal and 2nd AUDIO OUT plugs while listening to any source (other than “AM” and “USB”) through the speakers.

• You cannot select “AM” or “USB” as the source when Dual Zone is activated.

• When Dual Zone is in use, you can only operate the DVD/CD player using the remote controller. For operations, see pages 20 – 25.

These operations are possible on the monitor using the remote controller.

Activate Dual Zone.

• DUAL indicator lights up on the display.

The main source automatically changes to “DISC.” To select a different source (main source) to listen through the speakers, press SOURCE on the control panel.

• By using the buttons on the control panel, you can operate the newly selected source without affecting Dual Zone operations.

Adjust the volume through the 2nd AUDIO OUT plug.

ENGLISH

To cancel Dual Zone operations

• DUAL indicator goes off.

—

Operate the DVD/CD player using the remote controller by referring to the monitor screen.

On the control panel:

Enter Dual Zone settings.

Activate or deactivate Dual Zone.

The source automatically changes to “DISC” when

Dual Zone is activated.

27OPERATIONS

Listening to the Bluetooth ® devices

For Bluetooth operations, it is required to connect the Bluetooth Adapter (KS-BTA200) to the CD changer jack on the rear of this unit.

ENGLISH

• Refer also to the instructions supplied with the Bluetooth adapter and the Bluetooth device.

• Refer to the list (included in the box) to check the countries where you may use the Bluetooth ® function.

To use a Bluetooth device through the unit (“BT-PHONE” and “BT-AUDIO”) for the first time, you need to establish Bluetooth wireless connection between the unit and the device.

• Once the connection is established, it is registered in the unit even if you reset your unit. Up to five devices can be registered in total.

• Only one device can be connected at a time for each source (“BT-PHONE” and “BT-AUDIO”).

Registering a Bluetooth device

Registration (Pairing) methods

Use either of the following items in the Bluetooth menu to register and establish the connection with a device.

• Select “BT-PHONE” or “BT-AUDIO” as the source to operate the Bluetooth menu.

Open Make the unit ready to establish a new

Bluetooth connection. Connection is established by operating the Bluetooth device.

Search Make the unit ready to establish a new

Bluetooth connection. Connection is established by operating the unit.

• When move back to the previous screen by pressing number button 3.

is shown on the display, you can

Registering using “Open”

Preparation: Operate the device to turn on its

Bluetooth function.

1 Select “BT-PHONE” or “BT-AUDIO.”

2 Select “New.”

3 Enter setting menu.

4 Select “Open.”

5 Enter a PIN (Personal Identification Number)

code to the unit.

• You can enter any number you like (1-digit to 16-digit number). [Initial: 0000]

• To enter a PIN code less than 4-digit, firstly delete the initial PIN code (0000) by pressing number button 5 ( ) .

* Some devices have their own PIN code. Enter the

specified PIN code to the unit.

1 Move to the next (or previous) number

position.

2 Select a number or blank space.

2 Select a device you want to connect.

3 Repeat steps 1 and 2 until you finish

entering a PIN code.

4 Confirm the entry.

“Open...” flashes on the display.

6 Use the Bluetooth device to search and

connect.

On the device to be connected, enter the same

PIN code you have just entered for this unit. “Connected (and device name)” appears on the display.

Now connection is established and you can use the

device through the unit.

The device remains registered even after you disconnect the device. Use “Connect“ (or activate “Auto Connect”) to connect the same device from next time on. (See the following and page 52.)

Connecting a device

Perform steps 1 – 3 on page 28, then...

1 • Select “Search” to search for available

devices.

The unit searches and displays the list of the

available devices.

If no available device is detected, “Device not

found” appears.

• Select “Special” to connect a special device.

The unit displays the list of the preset devices.

3 • For available devices...

1 Enter the specific PIN code of the device to

the unit.

Refer to the instructions supplied with the

device to check the PIN code.

2 Use the Bluetooth device to connect. Now connection is established and you can

use the device through the unit.

• For special device...

Use “Open” or “Search” to connect.

Connecting/disconnecting/deleting a registered device

1 Select “BT-PHONE” or “BT-AUDIO.”

2 Select a registered device you want to

connect/disconnect/delete.

3 Enter setting menu.

4 • Select “Connect” or “Disconnect” to

connect/disconnect the selected device.

ENGLISH

Continued on the next page

EXTERNAL DEVICES

• Select “Delete,” then confirm the selection.

ENGLISH

You can set the unit to connect the Bluetooth device automatically when the unit is turned on. (See “Auto Connect” on page 52.)

Using the Bluetooth cellular phone

When a call comes in....

The source is automatically changed to “BT-PHONE.”

When “Auto Answer” is activated....

The unit answers the incoming calls automatically, see page 52.

• When “Auto Answer” is deactivated, press any button (except /control dial) to answer the incoming call.

Select “BT-PHONE.”

Enter Bluetooth menu.

Establish the connection with a device, then make a call (or settings

—

using the Bluetooth menu). (See pages 31 and 52.)

When a text message comes in....

If the cellular phone is compatible with Text Message (notified through JVC Bluetooth adapter) and “Message Info” is set to “Auto” (see page 52), the unit rings and “Received Message” appears on the display to inform you of the message arrival.

Press number button 3 to select “No” or return to the previous screen.

To end the call

Hold any button (except /control dial).

• You can adjust the microphone volume level (see page 52).

+ 237 hidden pages