JVC HV-32P40BU, HV-28P40BU User Manual

HV-32P40BU
HV-28P40BU

ENGLISH

DEUTSCH

FRANÇAIS

NEDERLANDS

CASTELLANO

ITALIANO

PORTUGUÊS

COLOUR TELEVISION

FARBFERNSEHGERÄT
TELEVISEUR COULEUR
KLEURENTELEVISIE
TELEVISOR A COLOR
TELEVISORE A COLORI
TELEVISOR A CORES

INSTRUCTIONS

BEDIENUNGSANLEITUNG

MANUEL D’INSTRUCTIONS

GEBRUIKSAANWIJZING

MANUAL DE INSTRUCCIONES

ISTRUZIONI

INSTRUÇÕES

How to move the TV

When moving the TV, make sure that it is held by two people as shown in the illustration. Be careful
not to trap your hands when putting the TV down.

1

2

ENGLISH

3

1

Thank you for buying this JVC colour television.
To make sure you understand how to use your new TV, please read this manual thoroughly before you
begin.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

• Operate only from the power source specified (AC 220 – 240 V, 50 Hz) on the unit.

• Avoid damaging the AC plug and power cord.

• When you are not using this unit for a long period of time, it is recommended that you disconnect
the power cord from the mains outlet.

Distance recommendations

Avoid improper installation and never position the unit
where good ventilation is impossible.
When installing this TV, distance recommendations
must be maintained between the set and the wall, as well
as inside a tightly enclosed area or piece of furniture.
Keep to the minimum distance guidelines shown for safe
operation.

Failure to take the following precautions may result in damage to the TV or
remote control.

DO NOT block the TV’s ventilation openings or holes.

(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be
able to get out.)

DO NOT place anything on top of the TV.

(such as cosmetics or medicines, flower vases, potted plants, cups, etc.)

DO NOT allow objects or liquid into the cabinet openings.

(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

DO NOT place any naked flame sources, such as lighted candles, on the TV.

The surface of the TV screen is easily damaged. Be very careful with it when handling the TV.
Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it hard.
Never use any cleaner or detergent on it.

In the event of a fault, unplug the unit and call a service technician. Do not attempt to repair it
yourself or remove the rear cover.

D.I.S.T. demonstration

To start the D.I.S.T. demonstration:
Press the H button to display the menu bar. Then press the yellow button.
A picture split in two (D.I.S.T. turned on and D.I.S.T. turned off) will appear on the screen.

To quit the D.I.S.T. demonstration:
Press the yellow button, b button, p p buttons or any of the number buttons.

2

To enjoy even better picture quality

The picture quality of this TV is controlled by a combination of three functions (PICTURE MODE,
DIGITAL VNR, and Super DigiPure).
By adjusting these three functions, you can change the picture quality to suit your preferences. The
initial settings of the three functions are as follows.

PICTURE MODE : BRIGHT

DIGITAL VNR : AUTO(LOW)

Super DigiPure : AUTO

 If you want a sharper picture, change to the following settings.

(However, the picture quality may not change very much if you are already watching a clear
picture.)

PICTURE MODE : BRIGHT

DIGITAL VNR : MIN

Super DigiPure : MAX

 If there is a lot of noise in the picture, change to the following settings.

PICTURE MODE : STANDARD

DIGITAL VNR : AUTO(HIGH)

Super DigiPure : MIN

ENGLISH

Note:

• For detailed information about how to change these settings, see “PICTURE menu” on
page 25.

3

CONTENTS

Setting up your TV ...................................5

Connecting the aerial and video cassette

recorder (VCR) ....................................... 5

Connecting the power cord to the AC

outlet....................................................... 6

Putting the batteries into the remote

control..................................................... 6

Initial settings ............................................. 6

T-V LINK functions..................................... 9

TV buttons and functions......................11

Turn the main power on ........................... 11

Choose a TV channel .............................. 11

Adjust the volume .................................... 11

Remote control buttons and

functions..............................................12

Turn the TV on or off from standby mode
Choose a TV channel and watch images

from external devices ........................... 13

Adjust the volume .................................... 14

Information function ................................. 14

ZOOM function......................................... 15

3D CINEMA SOUND function.................. 16

Return to TV channel instantly................. 16

Using the “Freeze” function...................... 16

Using the “Multi-picture” function ............. 17

Favourite channel function....................... 19

Operating a JVC brand VCR or DVD

player.................................................... 20

.. 12

Teletext function ....................................21

Basic operation ........................................ 21

Using the List Mode ................................. 21

Hold.......................................................... 22

Sub-page ................................................. 22

Reveal...................................................... 22

Size .......................................................... 22

Index ........................................................ 23

Cancel...................................................... 23

Top overview............................................ 23

Subtitle ..................................................... 23

Using the TV’s menu..............................24

Basic operation ........................................ 24

PICTURE menu ......................................25

PICTURE MODE...................................... 25

CONTRAST ............................................. 25

BRIGHT.................................................... 25

SHARP..................................................... 25

COLOUR.................................................. 25

HUE.......................................................... 25

COLOUR TEMP....................................... 25

FEATURES .............................................. 26

SOUND menu ......................................... 29

STEREO / I • II ......................................... 29

BASS........................................................ 29

TREBLE ................................................... 29

BALANCE ................................................ 29

HEADPHONE VOLUME .......................... 29

3D CINEMA SOUND................................ 29

FEATURES menu................................... 30

SLEEP TIMER ......................................... 30

ON TIMER................................................ 30

CHILD LOCK............................................ 31

APPEARANCE......................................... 32

BLUE BACK ............................................. 32

FAVOURITE SETTING ............................ 32

SET UP menu ......................................... 33

AUTO PROGRAM.................................... 33

EDIT/MANUAL ......................................... 33

LANGUAGE ............................................. 37

PICTURE TILT ......................................... 37

DECODER (EXT-2).................................. 37

COMPONENT AUTO SELECT ................ 38

EXT SETTING.......................................... 39

Additional preparation ..........................42

Connecting external equipment ...............42

CH/CC numbers ..................................... 44

Troubleshooting ....................................46

Specifications ........................................49

4

Setting up your TV

Caution

• Turn off all the equipment including the TV before connecting anything.

Connecting the aerial and video cassette recorder (VCR)

• The connecting cables are not provided.

• For further details, refer to the manuals provided with the devices to be connected.

 If you are connecting a VCR,

follow A → B → C in the diagram
opposite.

 If you are not connecting a VCR,

follow 1.

For example

75-ohm
Coaxial

Cable

ENGLISH

Aerial

To use the T-V LINK functions, you must
have a T-V LINK compatible VCR
connected by a SCART cable C to the EXT­2 terminal on the TV. For details about T-V
LINK functions, see “T-V LINK functions”
on page 9.

• You can watch a video using the VCR

without doing C. For details, see your
VCR instruction manual.

• To connect more equipment, please see
“Connecting external equipment” on
page 42.

• To connect additional audio equipment,
see “Connecting speakers/amplifier” on
page 43.

• If you connect a decoder to a T-V LINK
compatible VCR, set the DECODER
(EXT-2) function to ON. For details, see
“DECODER (EXT-2)” on page 37.
Otherwise, you will not be able to watch
scrambled channels.

 Rear Panel

EXT-

4

Y

PrPbR

L

L

AUDIO OUT

R

EXT-1

EXT-3

EXT-2

S

S

Back of the TV

EXT-

21-pin

SCART

Cable

VCR

4

Y

L

PrPbR

L

R

AV IN/OUT

Terminal

AUDIO OUT

EXT-1

EXT-2

S

EXT-3

S

75-ohm
Coaxial

To Aerial

To Aerial

Cable

Input

Output

1 Aerial socket (page 5)
2 EXT-1 terminal (pages 5, 39, 42)
3 EXT-2 terminal (pages 5, 9, 39, 42)
4 EXT-3 terminal (pages 39, 42)
5 EXT-4 terminal (pages 39, 42)
6 AUDIO OUT terminal (page 43)

5

Setting up your TV

s

Connecting the power cord to the AC outlet

Caution

• Operate only from the power source
specified (AC 220 – 240 V, 50 Hz) on
the unit.

• Failure to use the supplied power cord
or to insert it into a correctly earthed
outlet may result in electric shocks.

Putting the batteries into the remote control

Use two AA/R6 dry cell batteries.
Insert the batteries from the - end, making
sure the + and - polarities are correct.

• Follow the warnings printed on the
batteries.

• Battery life is about six months to one
year, depending on how much you use the
remote control.

• The batteries we supply are only for
setting up and testing your TV, please
replace them as soon as you need to.

• If the remote control does not work
properly, replace the batteries.

Initial settings

When the TV is first turned on, it goes into
the initial settings mode, and you will see the
JVC logo. Follow the instructions on the
screen display to make the initial settings.

Yellow button

Blue button

7 button

1 Press the A button on the TV

The power lamp lights green and the JVC
logo appears.

A button Power lamp

• If the JVC logo does not appear this is
because your TV has already been
turned on for the first time:
use the “LANGUAGE” and “AUTO
PROGRAM” functions to make the
initial settings. For details, see “SET
UP menu” on page 33.

6

Setting up your TV

2 Press the a button

The LANGUAGE menu appears.

> LANGUAGE

OK

D0002(E)-EN

3 Press the 6 buttons to choose

ENGLISH. Then press the a
button

The on-screen display will then be in
English.
The COUNTRY menu appears as a sub­menu of the AUTO PROGRAM function.
There are two COUNTRY menus.
Pressing the yellow button changes the
COUNTRY menu as follows:

> COUNTRY

OK

> COUNTRY

OK

D0003-EN

START

MORE

START

MORE

4 Press the 5 and 6 buttons to

choose the country where you are

5 Press the blue button to start the

AUTO PROGRAM function

The AUTO PROGRAM menu appears
and received TV channels are
automatically stored in the programme
numbers (PR).

>> AUTO PROGRAM

CH 28

14%

OK

D0004-EN

• Perform the “ACI function” operation
(see page 8) when “ACI START/ACI
SKIP” is displayed.

• To cancel the AUTO PROGRAM
function:
Press the b button.

After the TV channels have been
registered in the programme
numbers (PR), the EDIT menu
appears

> EDIT

D0038-EN

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

MOVE

BBC1

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

ID

INSERT

21
22
23
24
25
26
01
02
03

MANUAL

DELETE

• If you want to, you can now edit the
programme numbers (PR) using the
EDIT/MANUAL function. For details,
see “EDIT/MANUAL” on page 33.

• If you do not want to edit programme
numbers (PR), go to the next step.

ENGLISH

7

Setting up your TV

6 Press the a button to display the

T-V LINK menu

T-V LINK

DOWNLOAD TV RECORDING DEVICE

OK

D0005

EXIT

-EN

If you do not have a T-V LINK
compatible VCR connected:

Press the b button to exit the T-V LINK
menu.
The T-V LINK menu disappears.

If you have a T-V LINK compatible
VCR connected to the EXT-2
terminal:

Follow the operating procedure
“Downloading the data to VCR” on
page 9 to transmit the Programme number
(PR) data.

Now, the initial settings are complete,
and you can watch the TV

• If your TV can detect the TV channel
name from the TV channel broadcast
signal, the TV channel name is assigned
to the programme number (PR) to which
the TV channel has been set. However,
which TV channels are set to which
programme numbers (PR) will depend on
the area in which you live.

• If a TV channel you want to view is not
set to a programme number (PR), you can
set it using the MANUAL function. For
details, see “EDIT/MANUAL” on
page 33.

• The AUTO PROGRAM function does not
set the programme number PR 0 (AV) for
your video cassette recorder. You will
need to set this using the MANUAL
function.

 ACI function

This TV has an ACI function which decodes
the ACI (Automatic Channel Installation)
data.
Using the ACI function allows all TV
channels transmitted from the cable TV
station to be properly registered quickly
according to the data from the cable TV
station.

If “ACI START/ACI SKIP” appears in
the AUTO PROGRAM menu:

You can use the ACI (Automatic Channel
Installation) function to decode the ACI data
and complete the registration of all the TV
channels in a short period of time.

Press the 6 buttons to choose ACI
START. Then press the a button to
start the ACI function

Depending on your cable TV station, there
may be a broadcast selection menu set up by
the cable TV station.
Follow the menu instructions and use the
5 and 6 buttons to operate the menu.
After you have made the setting, press the
a button.

• If you have any questions about the items
in the Broadcast Selection menu or how to
operate the menu, please contact your
cable TV station.

• If you do not want to use the ACI
function, press the 6 buttons to choose
ACI SKIP and then press a.

• When the cable TV broadcast reception is
poor, the ACI function will not work
properly.

• If there is an error in the ACI data itself,
the TV channel cannot be registered
properly. If this happens, turn the ACI
function off (ACI SKIP) and use the
AUTO PROGRAM function.
Alternatively, use the EDIT/MANUAL
function to correct the Programme
number (PR) setting.

8

Setting up your TV

If “ACI ERROR” is displayed in the
AUTO PROGRAM menu:

“ACI ERROR” means that the ACI function
is not working properly. Press the 2 button
to start the ACI function again.
If “ACI ERROR” still appears even after you
have tried to start the ACI function several
times, press the 3 button to start the AUTO
PROGRAM function. It does not cause any
problem because all the TV channels are
registered to the Programme numbers (PR)
by the AUTO PROGRAM function.

 Downloading the data to VCR

You can transmit to the latest Programme
numbers (PR) data to a VCR with the T-V
LINK function.

Caution

• This only works when a T-V LINK
compatible VCR is connected to the
EXT-2 terminal.

• This only works when the T-V LINK
menu is being displayed.

T-V LINK

DOWNLOAD TV RECORDING DEVICE

OK

D0005

1 Turn on the VCR

2 Press the a button

The data transmission begins.

TV RECORDING DEVICE

TRANSFER. . . . .

D0037

The T-V LINK menu disappears once the
data transmission ends.

When the T-V LINK menu is
changed over to another menu:

The TV has finished its menu. This new
menu is operated from the VCR. See the
VCR instruction manual for what to do
next.

EXIT

-EN

-EN

If “FEATURE NOT AVAILABLE”
appears at the T-V LINK menu:

Check the following three items. Then
press the 2 button to retry data
transmission.

• Has a T-V LINK compatible VCR
been connected to the EXT-2
terminal?

• Has the VCR power been turned on?

• Does the SCART cable that is
connected to the EXT-2 terminal to T­V LINK compatible VCR have all its
proper connections?

T-V LINK functions

When you have a T-V LINK compatible
VCR connected to the EXT-2 Terminal on
the TV, it is easier to set up the VCR and to
view videos. T-V LINK uses the following
features:

To use T-V LINK functions:

A “T-V LINK compatible VCR” means a
JVC video cassette recorder with the T-V
LINK logo, or with one of the following
logos. However, these VCRs may support
some or all of the features described earlier.
For details, see your VCR instruction
manual.

“Q-LINK” (a trademark of Panasonic
Corporation)
“Data Logic” (a trademark of Metz
Corporation)
“Easy Link” (a trademark of Phillips
Corporation)
“Megalogic” (a trademark of Grundig
Corporation)
“SMARTLINK” (a trademark of Sony
Corporation).

ENGLISH

9

Setting up your TV

 Pre-set download

The VCR will automatically download the
registered data on the TV channels from the
TV. This means you do not need to set up the
program channels on your VCR manually.
The preset download function automatically
begins when the initial setting is complete or
whenever you carry out the AUTO
PROGRAM or EDIT/MANUAL functions.

You can also carry out this function using
your VCR controls.

When “FEATURE NOT AVAILABLE” is
displayed:

If “FEATURE NOT AVAILABLE” is
displayed, the download was not performed
correctly. Before trying to download again,
check that:

• the VCR power is turned on

• the VCR is T-V LINK compatible

• the VCR is connected to the EXT-2
terminal

• the SCART cable is fully wired.

 Direct Rec

“What You See Is What You Record”
You can easily record to VCR the images

that you are watching on the TV.
For details, read the manual for your VCR.

Use your VCR controls. “DEVICE IS
RECORDING” is displayed.

In the following situations, the VCR
will stop recording if the TV is turned
off, if the TV channel or input is
changed, or if the menu is displayed
on the TV:

• when recording images from an external
device connected to the TV (for example
a camcorder)

• when recording a TV channel after it has
been unscrambled on a decoder

• when recording a TV channel by using the
TV’s output because the VCR’s own
tuner cannot properly receive that
channel.

You cannot carry out Direct Rec using your
TV’s control.
Generally, the VCR cannot record a TV
channel that it cannot receive properly on its
own tuner, even if you can view that TV
channel on the TV. However, some VCRs
can record a TV channel by using the TV’s
output if that channel can be viewed on the
TV. For details, see your VCR instruction
manual.

When the VCR is not ready, the following
messages are displayed.

ERROR
MESSAGE

NO
RECORDING

NO
RECORDING
POSSIBLE

NO
RECORDING,
MEDIA
PROBLEM

NO
RECORDING,
DEVICE BUSY

Cause and
countermeasure

The VCR is not able to
record.
Check the VCR.

The TV input is set to EXT-4.
Since the EXT-4 picture
cannot be output to EXT-2,
DIRECT REC is not possible.

The recording device is not
ready to record. Check the
VCR tape.

The recording device cannot
record as it is recording or
playing. Check the VCR.

Refer to the VCR instruction manual.

10

TV buttons and functions

Turn the main power on

Press the A button on the TV.

The power lamp lights red and your TV is in
the standby mode.

• If the power lamp lights green, the TV is

To turn the main power off:

Press the A button again.
The power lamp goes off.

Caution

•The A button on the TV does not fully

isolate the TV from the AC supply. If you
are not going to use the TV for a long
period, be sure to disconnect the AC plug
from the AC socket.

Choose a TV channel

Press the P p buttons to choose a
programme number (PR) or an EXT
terminal

Adjust the volume

already on.

ENGLISH

S

R

/

MONO

L

EXT-5

P

R

L

/

MONO

EXT-5

P

S

See the pages in brackets for details.

1 A (main power) button (pages 6, 11)
2 Power lamp (pages 6, 11)
3 Remote control sensor
4 r (Volume) button (page 11)
5 P p buttons/ q buttons (page 11)
6 Headphone jack (mini jack) (page 42)
7 EXT-5 terminal (pages 39, 42)

1 Press the r (Volume) button once

The volume level indicator appears.

2 Press the q buttons while the

volume level indicator is displayed

11

Remote control buttons and functions

1 Muting button
2 Number buttons
3 Information button

1

2

3

4
5

6

7
8

9

0

­=

~

!

@
#

$
%

^
&

*

(

4 c button
5 i button
6 b button
7 7 buttons
8 g (Text) button
9 p p buttons
0 VCR/DVD/Teletext control buttons

- p buttons
= d (Favourite) button
~ # (Standby) button
! VCR/TV/DVD switch
@ G button
# Colour buttons
$ X (Multi) button
% f/g (Freeze/Swap) button
^ H button
& a button
* b button
( r (Volume) q buttons

Turn the TV on or off from standby mode

Press the # (standby) button to turn
the TV on or off

When the TV is turned on, the power lamp
changes from red to green.

• The power can be turned on by pressing

the b button, p p buttons or Number
buttons.

12

To turn the TV on or off, set the VCR/TV/
DVD switch on the remote control to the
TV position and press the # button.
If the VCR/TV/DVD switch on the remote
control is set to a position other than TV,
the TV will not be turned on or off even if
the # button is pressed.

Remote control buttons and functions

Choose a TV channel and watch images from external devices

 Use the number buttons:

Enter the programme number (PR)
of the channel using the number
buttons.

Example:

•PR 6 → press 6

• PR 12 → press 1 and 2

 Use the p p buttons:

Press the p p buttons to
choose the programme number
(PR) you want or an EXT terminal.

 Use the AV button:

Press the AV button to choose an
EXT terminal.

TV mode EXT modes

Programme

numbers

PR 1 – PR 99

EXT-1

EXT-5

or

• You can choose a video input signal
from the S-VIDEO signal (Y/C signal)
and regular video signal (composite
signal). For details, see “S-IN (S­VIDEO input)” on page 39.

• If you do not have a clear picture or no
colour appears, change the colour
system manually. See “COLOUR
SYSTEM” on page 27.

• If you choose an EXT terminal with no
input signal, the EXT terminal number
becomes fixed on the screen.

E3

EXT-2

or

EXT-3

or

EXT-4

S3

• This TV set has a function which can
automatically change over the input
according to a special signal output
from an external device. (The EXT-4
and EXT-5 terminals do not support
this function.)

• Since this TV is designed to make full
use of the resolution of the original
video source, the motion may appear
unnatural when the video source is
input with 625p progressive-scanning
component signals.
If this happens, change the output
setting of the connected device to 625i
interlace-scanning component signal
output. See the instructions that came
with the device for more information.

To return to a TV channel:

Press the b button, the 6 buttons or the
number buttons.

To use the programme number PR 0
(AV):

When the TV and VCR are connected only
by the aerial cable, choosing the programme
number PR 0 (AV) allows you to view
images from the VCR. Set the VCR RF
channel to the programme number PR 0
(AV) manually. For details, see “EDIT/
MANUAL” on page 33.
Pressing the G button changes the choice as
follows:

TV mode

Programme

numbers

PR 1 – PR 99

PR 0

EXT modes

EXT-1

EXT-5

or

E3

EXT-2

or

EXT-3

or

EXT-4

S3

ENGLISH

13

Remote control buttons and functions

• The VCR sends its playback image along
the aerial cable as an RF (radio frequency)
signal.

• Also see your VCR instruction manual.

Adjust the volume

Press the r q buttons to adjust
the volume.

The volume level indicator appears and the
volume changes as you press the r q
buttons.

 Muting the sound

Press the l (muting) button to
turn off the sound.

Pressing the l (muting) button again
restores the previous volume level.

Information function

You can see the channel number of the
programme you are watching, the current
time or the PR LIST.
From the PR LIST, you can choose a channel
or EXT terminal.

Press the h (Information) button to
display the information you want to

see.

Pressing the h (Information) button changes
the display as follows:

PR LIST

D0011-EN

PR ID

AV
01
02
03
04
05
06
07
08
09

OK

BBC1

+10-10

Channel number display

12 : 00

No indication

Channel number display:

The channel number and channel name
(when the channel name is registered) of the
programme you are watching or the EXT
terminal number is displayed.

Time display:

The current time of the teletext data is
displayed.
If the TV has not received a TV channel that
has teletext programmes since it was turned
on, the time display is blank. To view the
current time, choose a TV channel that has
teletext programmes.

• An incorrect current time is sometimes
displayed when watching videos.

PR LIST:

The programme number (PR) and EXT
terminal list is displayed.
Pressing the a button after choosing the
programme number (PR) or EXT terminal
with the 7 buttons will display the
chosen programme or EXT terminal.

• For programme numbers (PR) for which
the CHILD LOCK function is set, the n
(CHILD LOCK) mark is displayed. For
details see “CHILD LOCK” on page 31.

• For programme numbers (PR) which is
registered as a favourite channel, the d
(favourite) mark is displayed. For details
see “Favourite channel function” on
page 19.

14

Remote control buttons and functions

ZOOM function

You can change the screen size according to
the picture aspect ratio. Choose the optimum
one from the following ZOOM modes.

AUTO:

When a WSS (Wide Screen Signalling)
signal, which shows the aspect ratio of the
picture, is included in the broadcast signal or
the signal from an external device, the TV
automatically changes the ZOOM mode to
16:9 ZOOM mode or FULL mode according
to the WSS signal.
If a WSS signal is not included, the picture is
displayed according to the ZOOM mode set
with the 4:3 AUTO ASPECT function.

• For details of the 4:3 AUTO ASPECT
function, see “4:3 AUTO ASPECT” on
page 28.

• When the AUTO (WSS) mode does not
function correctly due to poor WSS signal
quality or when you want to change the
ZOOM mode, press the c button
and change to another ZOOM mode.

REGULAR:

Use to view a normal picture (4:3 aspect
ratio) as this is its original shape.

PANORAMIC:

This stretches the left and right sides of a
normal picture (4:3 aspect ratio) to fill the
screen, without making the picture appear
unnatural.

• The top and bottom of the picture are
slightly cut off.

14:9 ZOOM:

This zooms up the wide picture (14:9 aspect
ratio) to the upper and lower limits of the
screen.

16:9 ZOOM:

This zooms up the wide picture (16:9 aspect
ratio) to the full screen.

16:9 ZOOM SUBTITLE:

This zooms up the wide picture (16:9 aspect
ratio) with subtitles to the full screen.

FULL:

This uniformly stretches the left and right
sides of a normal picture (4:3 aspect ratio) to
fill the wide TV screen.

• For 16:9 aspect ratio pictures that have
been squeezed into a normal picture (4:3
aspect ratio), use the FULL mode to
restore the picture to its original shape.

 Choose the ZOOM mode

1 Press the c button to display

the ZOOM menu

ZOOM

AUTO
REGULAR
PANORAMIC
14:9 ZOOM
16:9 ZOOM
16:9 ZOOM SUBTITLE
FULL

OK

D0009-EN

2 Press the 6 buttons to choose a

ZOOM mode. Then press the a
button

The picture expands and the chosen
ZOOM mode is displayed in about 5
seconds.

• The ZOOM mode may be
automatically changed by the control
signal from an external device. When
you want to return to the previous
ZOOM mode, choose the ZOOM
mode again.

ENGLISH

15

Remote control buttons and functions

 Adjusting the visible area of the

picture

If subtitles or the top (or bottom) of the
picture are cut off, you can adjust the visible
area of the picture manually.

1 Press the c button

The ZOOM menu appears.

2 Press the a button to display the

ZOOM mode indicator

The indicator appears.

16 : 9 ZOOM

D0010-EN

3 While it is displayed, press the 6

buttons to change the position of
the picture

• You cannot adjust the visible area in
REGULAR or FULL mode.

The visible area adjustment is saved even
after the TV channel is changed.
However, it is cancelled if the following
operations are performed.

• The power is turned off/on

• The ZOOM mode is changed

• The X (Multi) button, f (Freeze)
button, or g (Text) button is pressed

• The TV is switched between TV mode
and EXT mode

3D CINEMA SOUND function

You can enjoy sounds with a wider
ambience.

• This function does not work for the sound
from headphones.

OFF:

The 3D CINEMA SOUND function switches
off.

• You can choose the 3D CINEMA
SOUND mode with the “SOUND menu”
(see page 29).

Return to TV channel instantly

You can return to a TV channel instantly.

Press the b button

The TV returns to the TV mode and a TV
channel appears.

Using the “Freeze” function

You can view the current programme as a
still picture.

1 Press the f button

The still picture of the current picture will
appear.

current

programme

D0056

To cancel the “Freeze” function:

Press the f button, the p p buttons or
the number buttons.

• The “Freeze” function does not work
while a sub-picture is displayed.

• The still picture cannot be output from
the TV.

still picture

Press the i button to select one of
3D CINEMA SOUND modes

ON:

When you listen to stereo sound, please
select ON mode.

MONO:

Select the MONO mode, when you listen to
the mono sound.

16

Remote control buttons and functions

Using the “Multi-picture” function

1 Press the X button

The “Multi-picture” menu appears.

1

D0101-EN

2 Press the 5 buttons to choose

the number of screens and then
press the a button

1

D0102

2

D0103

12

D0104

2-pictures multi:

Main-

picture

12-pictures multi:

D0058

212

Choose to return to one screen.

Choose to change to 2-pictures multi.

Choose to change to 12-pictures multi.

Sub­picture

D0056

Still
pictures

Moving
picture

• When set to 2-pictures multi, the main­picture can be changed by pressing the
p p buttons. The sub-picture screen
can be changed by pressing the p
buttons.
When set to 12-pictures multi and
there are more than 12 pictures, the
next or previous 12 screens can be
displayed by pressing the p buttons.

Changing the sub-picture
Displaying the next or
previous 12 screens

• When set to 2-pictures multi, press the
g (swap) button to switch the main­picture and sub-picture.
Pay attention to the following.

- When the EXT-4 picture is a picture

of 625p or 525p signal, you cannot
choose EXT-4 with the p buttons.

- When the EXT-4 picture signal is

changed to 625p, 525p or 1125i
signal while the EXT-4 picture is
displayed as the sub-picture, the 2­pictures multi function is cancelled.

• Do not press the g (swap) button
while you are recording the TV output
on the VCR. If you do, the TV output
signal will change.

• You cannot view a scrambled channel
in the sub-picture. If the g (swap)
button is pressed when viewing a
scrambled channel in the main-picture
using an external decoder, the channel
you have been viewing in the sub­picture will appear in both the main­picture and sub-picture.

ENGLISH

17

Remote control buttons and functions

• When set to 2-pictures multi and the
headphones are connected, the sound
for the main-picture is output from the
TV speakers and the sound from the
sub-picture is output from the
headphones.

- Adjust the volume of the sub-picture

To return the “Multi-picture” to one
screen:

Press the X button, press the 5
buttons to choose one screen, and then
press the a button.

• Pressing the b button will also return

the display to one screen.

sound from the headphones with
“HEADPHONE VOLUME” in the
“SOUND” menu (see page 29).

- The main-picture sound cannot be

heard through the headphones.

• When set to 12-pictures multi, press
the 7 buttons to choose the
screen you want to view and the press
the a button to display that picture
on the whole screen.

• The BLUE BACK function does not
work when the “Multi-picture”
function is being used.

• The ZOOM function does not work
when the “Multi-picture” function is
being used.

• When set to 2-pictures multi, you
cannot view a TV picture or a picture
from a component signal on more than
one screen at the same time.

Function

TV channel {{{{

1125i ××××

Component

Composite / S input × {{{

RGB × {{{

525p/625p × { ××

525i/625i × {{{

12-pictures

multi

2-pictures multi

swap

Main Sub

18

Remote control buttons and functions

Favourite channel function

You can register your favourite TV channels
(PR 1 – PR 99) in the number buttons 1 to 4.
After registering, the channel can be called
by pressing the d (favourite) button and a
number button 1 to 4.

 Favourite channel registration

1 In the normal screen, choose a TV

channel (PR 1 – PR 99) that you
want to register

For details, refer to “Choose a TV channel
and watch images from external devices”
on page 13.

2 Press and hold the d (favourite)

button for three seconds or more

Then “SET 1-4?” appears on the screen.

3 Press one of the number buttons 1

to 4

The current channel is registered in the
pressed number button.
After “PROGRAMMED!” appears on the
screen, the favourite channel icon appears
at the top-right of the screen.

• If the channel you are trying to register
is already registered in one of the other
number buttons 1 to 4, “NOT
AVAILABLE” appears on the screen.

• Channels locked with the CHILD
LOCK function cannot be registered.

• If AUTO PROGRAM is performed,
the registered favourite channels are
reset.

 Calling the favourite channel

1 In the normal screen, press the d

(favourite) button

Then “FAVORITE1-4?” appears.

2 Press one of the number buttons 1

to 4

The called favourite channel appears on
the screen.

• If a number button in which no
channel is registered is pressed, “NO
MEMORY” appears on the screen.

 Setting the picture effect

When a favourite channel has been chosen
with the d (favourite) button and number
buttons 1 to 4, picture effect settings can be
memorised for each favourite channel by
setting the picture effects in the PICTURE
menu (see page 25).
The following items in the PICTURE menu
(see page 25) are memorised.
PICTURE MODE
CONTRAST
BRIGHT
SHARP
COLOUR
HUE
COLOUR TEMP.
DIGITAL VNR
COLOUR SYSTEM
The last setting made for each item is
memorised.

ENGLISH

• When you want to delete a favourite
channel, delete the set channel and set
contents with FAVOURITE SETTING
(see page 32) in the FEATURES menu.

19

Remote control buttons and functions

Operating a JVC brand VCR or DVD player

These buttons will operate a JVC brand VCR
or DVD player. Pressing a button that looks
the same as the device’s original remote
control button has the same effect as the
original remote control.

1 Set the VCR/TV/DVD Switch to the

VCR or DVD position

VCR:

When you are operating the VCR, set the
switch to the VCR position.

• You can turn the VCR on or off with

the # (standby) button.

DVD:

When you are operating the DVD player,
set the switch to the DVD position.

• You can turn the DVD player on or off

with the # (standby) button.

2 Press the VCR/DVD Control Button

to control your VCR or DVD player

• If your device is not made by JVC,
these buttons will not work.

• Even if your device is made by JVC,
some of these buttons may not work,
depending on the device you are using.

• You can use the p buttons to choose
a TV channel the VCR will receive, or
choose the chapter the DVD player
plays back.

• Some models of DVD player use the
p buttons for both operating the fast
forward/backward functions and for
choosing the chapter. In this case, the
253 buttons do not work.

20

You cannot turn the TV on or off when the
VCR/TV/DVD switch is set to the VCR or
DVD position.
When you turn the TV on or off, set the
VCR/TV/DVD switch to the TV position.

Teletext function

VCR/TV/
DVD

4 Choose a teletext page by pressing

the p p buttons, number buttons
or colour buttons

To return to the TV mode:

Press the b button or g (Text) button.

Basic operation

1 Choose a TV channel with a teletext

broadcast

2 Set the VCR/TV/DVD switch to the

TV position

3 Press g (Text) button to display

the teletext

Pressing g (Text) button changes the
mode as follows:

TEXT
TEXT

D1043

TV mode

TEXT
TEXT

---

---

TV and text mode

Text mode

• If you have trouble receiving teletext
broadcasts, consult your local dealer or

ENGLISH

the teletext station.

• The ZOOM function will not work in
the TV and text mode or Text mode.

• You cannot operate TV’s menu when
viewing a teletext programme.

• Language display depends on the
country which was set on the
COUNTRY menu. If characters on a
Teletext programme do not appear
properly, change the COUNTRY
setting to other country’s. To change
the COUNTRY setting, perform steps
1 and 2 of the “AUTO PROGRAM”
procedure on page 33 and then press
the a button.

The last teletext page displayed is memorised.
The last teletext page is cleared under
following conditions.

• Turning the power off

• Changing the channel

---

---

• Switching the TV input

Using the List Mode

You can store the numbers of your favourite
teletext pages in memory and call them up
quickly using the colour buttons.

 To store the page numbers:

1 Press B button to go into the

List mode

The page numbers you have stored are
displayed at the bottom of the screen.

21

Teletext function

2 Press a colour button to choose a

position. Then press the number
buttons to enter the page number

3 Press and hold down the A (Store)

button

The four page numbers blink white to
show that they are stored in memory.

 To call up a stored page:

1 Press the B button to enter the

List mode

2 Press a colour button having a

stored page

To exit the List mode:

Press the B button again.

Hold

You can hold a teletext page on the screen for
as long as you want, even while several other
teletext pages are being received.

Sub-page

Some teletext pages include sub-pages that
are automatically displayed.

1 Choose a teletext page that

includes sub-pages

Sub-page numbers that can be viewed are
automatically displayed at the top of the
screen.

2 Press the 5 buttons to choose a

sub-page number

Reveal

Some teletext pages include hidden text
(such as answers to a quiz).
You can display the hidden text.

Each time you press the E (Reveal)
button, text is hidden or revealed

Size

You can double the height of the teletext
display.

Press the F (Size) button

Press the C (Hold) button

Hold indication

To cancel the Hold function:

Press C (Hold) button again.

22

Teletext function

Index

You can return to the index page instantly.

Press the G (Index) button

Returns to page 100 or a previously specified
page.

Cancel

You can search for a teletext page while
watching TV.

1 Press the number button to enter a

page number, or press a colour
button

The TV searches for a teletext page.

2 Press H (Cancel) button

The TV programme appears. When the
TV finds the teletext page, its page
number appears in the upper left of the
screen.

3 Press H (Cancel) button to return

to a teletext page when the page
number is on the screen

• The TV mode cannot be resumed by

pressing the H (Cancel) button. To
return to the TV mode press b.

1 Press the H button

The “Top overview” menu is displayed.

2 Choose the page by pressing the

6 buttons and the area by
pressing 5 buttons

ENGLISH

3 Press the a button

The selected page is displayed.

• When displaying the “Top overview”
menu, other Teletext functions cannot be
performed.

• The displayed information may differ
depending on the received signal.

Subtitle

You can search for and display “subtitle”
pages.

Press the h button

The TV searches for a “subtitle” page.

• The “subtitle” pages will be displayed in
the order they are received.

Top overview

You can directly access the pages of the
desired theme.
Top overview consists of two areas, Block
Pages and Group Pages. Each Block Page is
divided into Group Pages.

• For example if SPORTS is selected in the
Block Pages area, types of sport such as
TENNIS will be displayed in the Group
Pages area.

• This function is only for the TOP teletext
broadcasting system.

23

Using the TV’s menu

PICTURE

PICTURE

This TV has a number of functions you can
operate using menus. To use all your TV’s
functions, you need to understand the basic
menu operating techniques fully.

Buttons used to operate the menus

Basic operation

1 Press the H button to display

the menu bar

D0105-EN

2 Press the 5 buttons to choose

the menu you want to use and then
press the a button

D1105-EN

Chosen
menu

3 Press the 6 buttons to choose

the item to be set, press the 5
buttons to set the item, and then
press the a button

If there are sub-menus, use the 7
buttons to operate them.

• Press the b button to return to

the previous menu.

• Press the b or H button to exit

from the menu.

Chosen
menu name

Types of menu

PICTURE menu

D0106

Choose to set the screen
settings.

SOUND menu

D0107

Choose to set the sound settings.

FEATURES menu

D0108

Choose to set the sleep timer, on
timer and child lock settings.

SET UP menu

Choose to edit the channels or

D0109

set the display language
settings.

The menu guide area can be made to appear
and disappear for some menus.
While the menu is displayed, press the h
button to change between the guide area
being displayed and not displayed.

>> 4:3 AUTO ASPECT

PANORAMIC
REGULAR
14:9 ZOOM

OK

D0017-EN

Guide area

>> 4:3 AUTO ASPECT

PANORAMIC
REGULAR
14:9 ZOOM

D1017-EN

• The guide area for some menus will still

be displayed even if the h button is
pressed. This is not a fault.

• Some menu items may not be operated or
set depending on the TV status or other
menu item settings.
Menu items that cannot be operated or set
are displayed in grey in the menu and
cannot be chosen.

24

PICTURE menu

PICTURE

PICTURE MODE
CONTRAST
BRIGHT
SHARP
COLOUR
HUE
COLOUR TEMP.
FEATURES

D0014-EN

OK

STANDARD

COOL

RESET

• While the PICTURE menu is displayed,
pressing the blue button will set the
CONTRAST, BRIGHT, SHARP,
COLOUR, HUE settings to their default
settings.

• When watching the picture from EXT-1
to EXT-5, picture effect settings can be
memorised for each external input by
setting the picture effects in the PICTURE
menu.
The following items in the PICTURE
menu are memorised.
PICTURE MODE
CONTRAST
BRIGHT
SHARP
COLOUR
HUE
COLOUR TEMP.
DIGITAL VNR
COLOUR SYSTEM
The last setting made for each item is
memorised.

• For details on how to use these functions,
see “To enjoy even better picture quality”
on page 3.

PICTURE MODE

You can choose one of three PICTURE
MODEs to adjust the picture settings
automatically.

BRIGHT:

Heightens contrast and sharpness.

STANDARD:

Standardizes picture adjustment.

SOFT:

Softens contrast and sharpness.

CONTRAST

You can adjust the picture contrast.

2 :lower
3 : higher

BRIGHT

You can adjust the picture brightness.

2 : darker
3 : brighter

SHARP

You can adjust the picture sharpness.

2 : softer
3 :sharper

COLOUR

You can adjust the picture colour.

2 : lighter
3 :deeper

HUE

You can adjust the picture tint.

2 : reddish
3 :greenish

• You can change the HUE setting (picture
hue) when the colour system is NTSC

3.58, or NTSC 4.43.

COLOUR TEMP.

You can select one of three COLOUR
TEMP. modes (three tones of white) to adjust
the white balance of the picture. Since white
is the colour which is used as a reference for
all the other colours, changing the COLOUR
TEMP. mode affects the appearance of all
the other colours on the screen.

COOL:

A bluish white. Using this mode when
watching bright pictures allows you to enjoy
a more vivid and bright picture.

NORMAL:

The normal white colour.

ENGLISH

25

PICTURE menu

WARM:

A reddish white. Using this mode when
watching films allows you to enjoy colours
that are characteristic of films.

FEATURES

Choose FEATURES and press the a or 3
button to display the sub-menu.

> FEATURES

DIGITAL VNR
Super DigiPure
MOVIE THEATRE
Colour DigiPure
COLOUR SYSTEM
4:3 AUTO ASPECT

OK

D1015-EN

 DIGITAL VNR

The DIGITAL VNR function cuts down the
amount of ‘noise’ (‘snow’ or interference) in
the original picture.
You can choose from the three DIGITAL
VNR function settings of AUTO, MIN and
MAX.

AUTO(LOW)/AUTO(HIGH):

The TV will automatically adjust the level of
the DIGITAL VNR effect to match the
amount of noise in the picture, giving you the
best possible picture.

• If you set the DIGITAL VNR effect too
high it can make the picture less sharp. It is
recommended you use the AUTO(LOW)
setting if you can. If you set the DIGITAL
VNR function to AUTO(LOW) but still
notice some noise, change the setting from
AUTO(LOW) to AUTO(HIGH).

MIN:

The level of the DIGITAL VNR effect is set
to the minimum. If you set the DIGITAL
VNR function to AUTO(LOW) but feel that
the sharpness of the original picture has not
been reproduced fully, change the setting
from AUTO(LOW) to MIN.

• The MIN setting is not suitable for low­quality pictures which contain a lot of
noise.

AUTO(LOW)

AUTO
AUTO

ON

MAX:

The level of the DIGITAL VNR effect is set
to the maximum. If you set the DIGITAL
VNR function to AUTO(HIGH) but still
notice some noise, change the setting from
AUTO(HIGH) to MAX.

• The MAX setting is not suitable for high­quality pictures which contain very little
noise.

 Super DigiPure

The Super DigiPure function uses the latest
in digital technology to give you a natural­looking picture. The Super DigiPure function
includes the following two functions.

DigiPure function:

This function helps to create a natural­looking picture by eliminating unnecessary
edges from high-contrast and crisp images.
For images with low-contrast, edges are
added to produce a sharper, more detailed
picture.
You can choose from the three DigiPure
function settings of AUTO, MIN and MAX.

• If you set the DigiPure effect too high on
a low-quality picture that contains a lot of
noise, this may actually make the noise
worse. We recommend you use the
AUTO setting if you can.

Picture motion compensation
function:

This function displays fast-moving pictures
(for example, the players or ball in a football
game) more smoothly and naturally on the
screen.

• The effect level of the picture motion
compensation function cannot be
changed. The effect level is the same no
matter which of the AUTO, MIN or MAX
settings is used.

AUTO:

The TV will automatically adjust the level of
the DigiPure effect to match the amount of
noise in the picture, giving the best possible
picture.

26

PICTURE menu

MIN:

The level of DigiPure effect is set to the
minimum. When you set the Super DigiPure
function to AUTO and notice some noise,
change the setting from AUTO to MIN.

• The MIN setting is not suitable for high­quality pictures which contain very little
noise.

MAX:

The level of DigiPure effect is set to the
maximum. If you set the Super DigiPure
function to AUTO but feel that the original
picture quality has not been reproduced fully,
change the setting from AUTO to MAX.

• The MAX setting is not suitable for low­quality pictures which contain a lot of
noise.

OFF:

The Super DigiPure function is turned off.

 MOVIE THEATRE

The MOVIE THEATRE function displays a
cinema film picture more smoothly and
naturally on the screen.

AUTO:

The television automatically recognizes the
type of signal and turns the function on and
off.

ON:

This function is turned on.

OFF:

This function is turned off.

• The motion may appear unnatural when
viewing images with the NTSC colour
system. When the MOVIE THEATRE
function is set to AUTO or ON, the
motion may appear unnatural when
viewing images with the NTSC colour
system.

 Colour DigiPure

Makes the colour outline stand out and
increases the sharpness giving a clearer
picture.

ON:

Colour DigiPure works. Normally use with
this function turned on.

OFF:

Colour DigiPure does not work. This gives a
less clear picture than when this function is
turned on.

 COLOUR SYSTEM

The colour system is chosen automatically.
However, if the picture is not clear or no
colour appears, choose the colour system
manually.

1 Choose COLOUR SYSTEM. Then

press the a or 3 button

The sub-menu of the COLOUR SYSTEM
function appears.

>> COLOUR SYSTEM

MAIN

PAL

OK

D0016-EN

2 Press the 5 buttons to choose

MAIN or SUB
MAIN:

You can change the colour system of the
main-picture.

SUB:

You can change the colour system of the
sub-picture.

• Choose MAIN when a sub-picture is
not displayed.

SUB

AUTO

ENGLISH

27

PICTURE menu

3 Press the 6 buttons to choose

the appropriate colour system.
Then press the a button

PAL:

PAL system

SECAM:

SECAM system

NTSC 3.58:

NTSC 3.58 MHz system

NTSC 4.43:

NTSC 4.43 MHz system

AUTO:

This function detects a colour system
from the input signal. You can only use
this when you are viewing a picture from
programme number PR 0 (AV), or an
EXT terminal.

• The AUTO function may not function
properly if you have poor signal quality.
If the picture is abnormal in the AUTO
function, choose another colour system
manually.

• When in the Programme numbers PR 0
(AV) to PR 99, you cannot choose NTSC

3.58 or NTSC 4.43.

• COLOUR SYSTEM cannot be chosen
when you are watching the EXT-4 picture.

 4:3 AUTO ASPECT

You can choose one of three ZOOM modes,
REGULAR, PANORAMIC or 14:9 ZOOM,
as the ZOOM mode for the normal picture
(4:3 aspect ratio).

1 Choose 4:3 AUTO ASPECT then

press the a button

>> 4:3 AUTO ASPECT

PANORAMIC
REGULAR
14:9 ZOOM

OK

D0017-EN

2 Press the 6 buttons to choose a

ZOOM mode

28

SOUND menu

SOUND

STEREO/
BASS
TREBLE
BALANCE
HEADPHONE VOLUME
3D CINEMA SOUND

OK

D0019-EN

• Functions in the “SOUND” menu other
than “HEADPHONE VOLUME” work
for the TV speakers. They do not work for
the sound from the headphones.

• When the headphones are connected and
only one screen is displayed, only
“HEADPHONE VOLUME” can be used.

STEREO / I • II

When you are viewing a bilingual broadcast
programme, you can choose the sound from
Bilingual I (Sub I) or Bilingual II (Sub II). If
you have poor reception on a stereo
broadcast, you can change from stereo to
mono sound so that you can hear the
broadcast more clearly and easily.

s: Stereo sound

v : mono sound

t : Bilingual I (sub I)

u : Bilingual II (sub II)

• The sound mode you can choose differs
depending on the TV programme.

• This function does not work in the EXT
modes.

BASS

You can adjust the low tone of the sound.

2 : weaker
3 :strong

TREBLE

You can adjust the high tone of the sound.

2 : weaker
3 :strong

BALANCE

You can adjust the volume balance between
the left and right speaker.

2 : turn the left speaker’s volume level up.
3 : turn the right speaker’s volume level up.

HEADPHONE VOLUME

Adjust the volume of the sub-picture sound
which is heard through the headphones when
set to 2-pictures multi.

2 : Reduce volume
3 : Increase volume

• When not set to 2-pictures multi, the
headphone volume is adjusted with the
r q (volume) buttons.

3D CINEMA SOUND

Press the i button to set the 3D CINEMA
SOUND effect when 3D CINEMA SOUND
is set to ON or MONO.

Choose 3D CINEMA SOUND. Then
press the a or 3 button to display
the sub-menu.

> 3D CINEMA SOUND

SURROUND
BASS BOOST

OK

D0111 -EN

 SURROUND

Adjust the surround effect.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the surround
effect and choosing HIGH will increase the
surround effect.

 BASS BOOST

Adjust the bass sound.
You can choose HIGH, MID or LOW.
Choosing LOW will reduce the bass sound
and choosing HIGH will increase the bass
sound.

MID
MID

ENGLISH

29

FEATURES menu

FEATURES

SLEEP TIMER
ON TIMER
CHILD LOCK
APPEARANCE
BLUE BACK
FAVOURITE SETTING

OK

D0023-EN

TYPE A

ON

SLEEP TIMER

You can set the TV to automatically turn off
after a set period of time.

1 Choose SLEEP TIMER. Then press

the a or 3 button

A Sub-menu of the SLEEP TIMER
function appears.

> SLEEP TIMER

0120

OFF

OK

D0024-EN

2 Press the 5 buttons to set the

period of time. Then press the a
button

You can set the period of time for up to
120 minutes (2 hours) in 10 minute steps.

• One minute before the SLEEP TIMER
function turns off the TV,
“GOODNIGHT!” appears.

• The SLEEP TIMER function cannot
be used to turn off the TV’s main
power.

• When the SLEEP TIMER function is
on, you can display the sub-menu of
the SLEEP TIMER function again to
confirm or change the remaining
period of time of the SLEEP TIMER
function. Press the a button to leave
the menu after confirming or changing
the remaining time.

To cancel the SLEEP TIMER
function:

Press the 2 button to set the period of
time to “OFF”.

ON TIMER

You can set the TV to automatically turn on
to the TV channel you want after a set period
of time.

Choose ON TIMER. Then press the
a or 3 button to display the sub-
menu

> ON TIMER

PR
ON TIME

OK

D1111-EN

PR:

Set the TV channel.
You can set TV channels registered in the
Programme numbers (PR 1 – PR 99).

ON TIME:

Set the period of time.
You can set the period of time to a maximum
of 720 minutes (12 hours) in 15 minute steps.

• When the ON TIMER function is set, the
power lamp lights orange.

• ON TIMER settings are reset when the
main power is turned off.

• When the TV is already on and the ON
TIMER function is turned on,
“SWITCHING TO ON TIMER” is
displayed and the channel switches to the
set channel.

• If AUTO PROGRAM is performed, the
PR setting is reset to the default channel,
PR1.

• Channels locked with the CHILD LOCK
function cannot be set.

• When the SLEEP TIMER is set within the
same period of time, the ON TIMER will
be cancelled.

01

00:00

30

To cancel the ON TIMER function:

Press the 5 buttons to set a period of time
to “00:00”.

FEATURES menu

CHILD LOCK

When there is a TV channel you do not want
your children to watch, you can use the
CHILD LOCK function to lock out the TV
channel. Even when a child chooses a
programme number (PR) for a locked TV
channel the screen will change to blue and
display n (CHILD LOCK) so the TV channel
cannot be viewed. Unless you enter a pre-set
ID number by a special operation, the lock
cannot be released and the child cannot view
the TV channel.

 To set the CHILD LOCK function

1 Choose CHILD LOCK, then press

the 0 button

“SET ID NO.” (ID number setting screen)
appears.

> SET ID NO.

040

0

OK

D0025-EN

2 Set the ID number to your liking

1 Press the 6 buttons to choose

a number.

2 Press the 5 buttons to move

the cursor.

3 Press the a button

The Sub-menu of CHILD LOCK appears.

>> CHILD LOCK

D0026-EN

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

BBC1

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

21
22
23
24
25
26
01
02
03

LOCK

4 Press the 6 buttons to choose a

TV channel

Every time you press the 6 buttons, the
Programme number (PR) changes, and the
picture of the TV channel registered in the
Programme number (PR) is displayed on
the screen.

5 Press the blue button and set the

CHILD LOCK function.
Then press the a button

n (CHILD LOCK) appears and the TV
channel is locked.

To reset the CHILD LOCK function:

Press the blue button again.
n (CHILD LOCK) disappears.

To disable easy resetting of the CHILD
LOCK function, the menu disappears if
you choose the CHILD LOCK function
and press the a button.

 To view a locked TV channel

1 Choose a programme number (PR)

of a locked TV channel with the
number buttons or PR LIST

The screen changes to blue and the n
(CHILD LOCK) appears. You cannot
view the TV channel.

5

D0027-EN

2 Press the h (Information) button to

display “ID NO.” (ID No. input
screen)

5

ID NO. :

D0028-EN

3 Press the number buttons to enter

the ID number

The lock is temporarily released so you
can view the TV channel.

ENGLISH

31

FEATURES menu

If you have forgotten the ID
number:

Perform step 1 of “To set the CHILD
LOCK function”. After confirming the ID
number, press the b button to exit the
menu.

• Even if you reset the lock temporarily,
it does not mean that the CHILD
LOCK function set for the TV channel
is cancelled. The next time anyone
tries to view the TV channel, it will be
locked again.

• When you want to cancel the CHILD
LOCK function, you must perform the
operation “To set the CHILD LOCK
function” again.

• To stop it being easy to choose the
programme number (PR) of a locked
TV channel, the programme number
(PR) has been set so that it cannot be
chosen with the 6 buttons or the
buttons of the TV.

• To stop it being easy to reset the lock,
“ID NO.” (ID No. input screen) is set
so that it cannot appear unless you
press the h (Information) button.

APPEARANCE

Press the 5 button and choose the format
in which the channel number is displayed
from the three types: TYPE A, TYPE B and
TYPE C.

FAVOURITE SETTING

Choose when deleting the favourite channels
registered in the buttons 1 to 4.

• FAVOURITE SETTING cannot be selected
when the “Freeze” function or 2-pictures
multi function is being used.

1 Choose FAVOURITE SETTING,

then press the a or 3 button

The FAVOURITE SETTING menu
appears.

> FAVOURITE SETTING

1

2

3

4

OK

D0112-EN

2 Press the 6 buttons and choose

the favourite channel that you want
to delete

3 Press the blue button

The chosen favourite channel and set
contents are deleted.

• For details, see “Favourite channel
function” on page 19.

PR 07

PR 01

PR 01

PR 01

RESET

BLUE BACK

You can set the TV to automatically change
to a blue screen and mute the sound if the
signal is weak or absent, or when there is no
input from an external device.

ON:

This function is turned on.

OFF:

This function is turned off.

32

SET UP menu

SET UP

AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
PICTURE TILT
DECODER(EXT-2)
COMPONENT AUTO SELECT
EXT SETTING

OK

D0029-EN

ON
ON

AUTO PROGRAM

You can again perform the AUTO
PROGRAM function TV channel automatic
registration which was performed in the
“Initial settings” (page 6).

1 Choose AUTO PROGRAM, then

press the a or 3 button

The COUNTRY menu appears as a sub­menu of the AUTO PROGRAM function.
There are two COUNTRY menus.
Pressing the yellow button changes the
COUNTRY menu as follows:

> COUNTRY

OK

> COUNTRY

OK

D0003-EN

2 Press the 5 and 6 buttons to

choose the country where you are

3 Perform steps 5 and 6 of the “Initial

settings” (page 7)

START

MORE

START

MORE

EDIT/MANUAL

The EDIT/MANUAL functions are divided
into two types:

• editing the current programme numbers
(PR) (EDIT functions); and

• manually storing a TV channel you want
to view on a particular programme
number (PR) (MANUAL function).

Here are the details about these functions:

MOVE:

This function changes the programme
number (PR) of a TV channel.

ID:

This function registers a channel name (ID)
to a TV channel.

INSERT:

This function adds a new TV channel in the
current programme numbers (PR) list by
using the CH/CC number.

• You cannot use the INSERT function if
you do not know the channel number of a
TV channel. Use the MANUAL function
to register a TV channel in the programme
number (PR).

DELETE:

This function deletes a TV channel you do
not want to list.

MANUAL:

This function manually stores a new TV
channel in a programme number (PR).

Caution

• Using the MOVE, DELETE or INSERT
functions rewrites the current
programme numbers (PR) list.
Therefore, the programme numbers
(PR) of some of the TV channels will
change.

• Using the MANUAL function for a TV
channel for which the CHILD LOCK
function has been set cancels the
CHILD LOCK function for that channel.

• Using the MANUAL function for a TV
channel for which the DECODER
(EXT-2) function has been set to ON
returns the setting of the DECODER
(EXT-2) function for that channel to
OFF.

ENGLISH

33

SET UP menu

• When a TV channel has already been
registered in PR 99, using the INSERT
function deletes that TV channel.

 Basic operation

1 Choose EDIT/MANUAL, then press

the a or 3 button

The EDIT menu appears.

> EDIT

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

MOVE

D0038-EN

2 Follow the description for the

function you want to use

3 Press the a button to complete

the settings

The T-V LINK menu appears.

T-V LINK

DOWNLOAD TV RECORDING DEVICE

OK

D0005

EXIT

-EN

If you do not have a T-V LINK
compatible VCR connected:

Press the b button to exit the T-V LINK
menu.
The T-V LINK menu disappears.

If you have a T-V LINK compatible
VCR connected to the EXT-2 terminal:

Follow “Downloading the data to VCR” on
page 9 to transmit the programme number
(PR) data.

• For programme number PR 0, “AV”
appears in the programme numbers (PR)
list.

• An EXT terminal number does not appear
in the programme numbers (PR) list.

BBC1

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

ID

INSERT

21
22
23
24
25
26
01
02
03

MANUAL

DELETE

 MOVE

1 Press the 6 buttons to choose a

TV channel

2 Press the 3 button to start the

MOVE function

> EDIT

PR ID
AV
01
02
03
04
05
06
07
08
09

D0030-EN

CH/CC

CH

STORE

CH
CH
CH
CH
CH

CCCC02

21
22
23
24
25
26

03

CC

BBC1

OK

3 Press the 6 buttons to choose a

new programme number (PR)

To cancel the MOVE function:

Press the b button.

4 Press the 2 button to change the

programme number (PR) of a TV
channel to a new programme
number (PR)

 DELETE

1 Press the 6 buttons to choose a

TV channel

2 Press the yellow button to delete

the TV channel

The TV channel is deleted from the
programme numbers (PR) list.

01

34

SET UP menu

 ID

1 Press the 6 buttons to choose a

TV channel

2 Press the red button to start the ID

function

> EDIT

BBC1

BBC1

M

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

21
22
23
24
25
26
01
02
03

21
22
23
24
25
26
01
02
03

21
22
23
24
25
26
01
02
03

ID LIST

ID LIST

ID LIST
M6
MBC
MCM
MDR
MOVIE
MTV
MTV1
MTV2
MTV3

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

D0031-EN

3 Press the 6 buttons to choose

the first character of a channel
name (ID) you want to give the TV
channel

> EDIT

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

D0032-EN

4 Press the blue button to display the

ID LIST (channel name list)

> EDIT

PR ID
AV
01

BBC1
02
03
04
05
06
07

M
08
09

OK

D0033-EN

5 Press the 6 buttons to choose

the channel name (ID)

To cancel the ID function:

Press the b button.

6 Press the a button to give a

channel name (ID) to a TV channel

• You can give your own unique channel
name (ID) to the TV channel. When
you have finished step 3, do not go to
step 4. Press the 5 buttons to move
the cursor, and press the 6 buttons
to choose each character of the channel
name (ID). Then press the a button
to register the channel name (ID) to the
TV channel.

Before performing INSERT or
MANUAL operation

• If you register the TV channel (SECAM­L system) from a French station, be sure
to set the COUNTRY setting to
FRANCE. If the COUNTRY setting is
not set to FRANCE, perform steps 1 and 2
of the “AUTO PROGRAM” (page 33)
procedure and set the COUNTRY setting
to FRANCE before pressing the a
button.

• A CH/CC number unique to this TV and
corresponding to the Channel number of a
TV channel is required. Find the
corresponding CH/CC number from a
table “CH/CC numbers” on page 44 based
on the Channel number of the TV
channel.

• When the COUNTRY setting is not
FRANCE, use a two-digit CH/CC
number. When the COUNTRY setting is
FRANCE, use a three-digit CH/CC
number.

ENGLISH

35

SET UP menu

 INSERT

1 Press the 6 buttons to choose a

programme number (PR) for which
you will register a new TV channel

2 Press the green button and start

the INSERT function

> EDIT

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

D0034-EN

CH/CC

To cancel the INSERT function:

Press the b button.

3 Press the 6 buttons to choose

“CH” or “CC”, then enter the
remaining CH or CC number

When the COUNTRY setting is
FRANCE:

Choose “CH1”, “CH2”, “CC1” or “CC2”.

The TV shifts to registration mode.
When the registration is completed, the
picture of the TV channel appears on the
screen.

• The CH/CC number is a number given
to each broadcast frequency that
carries a TV channel. If the TV cannot
detect the TV channel corresponding
to the broadcast frequency indicated
by the CH/CC number, a “no-signal”
picture appears.

BBC1

CH/CC

CH
CH
CH
CH
CH
CH
CC
CCCC02

0 9

21
22
23
24
25
26

03

 MANUAL

1 Press the 6 buttons to choose a

programme number (PR) for a new
TV channel

2 Press the blue button to activate

the MANUAL function

> MANUAL

BBC1

CH/CC

CH
CH
CH
CH
CH
CH
CC
CC
CC

SEARCH+

SEARCH-

21
22
23
24
25
26

(

)

01

B / G
02
03

FINE-

FINE+

PR ID
AV
01
02
03
04
05
06
07
08
09

OK

SYSTEM

D0035-EN

To cancel the MANUAL function:

Press the b button.

3 Press the 3 button to choose the

SYSTEM (broadcasting system) for
a TV channel you want to register

TV channel (SECAM-L system)
from a French station:

Set the SYSTEM to “L”. If it is set to one
other than “L”, you cannot receive the TV
channel of the SECAM-L system.

Other TV channels:

If you do not know the correct
broadcasting system, set the SYSTEM to
“B/G”. If “B/G” is not correct, you will
not hear the sound normally when the TV
detects a TV channel. In this case, retry to
set the SYSTEM correctly so that no
problem arises.

4 Press the green or red button to

search for a TV channel

Scanning stops when the TV finds a TV
channel. Then the TV channel is
displayed.

36

SET UP menu

5 Press the green or red button

repeatedly until the TV channel you
want appears

If the TV channel reception is poor:

Press the blue or yellow button to fine­tune the TV channel.

6 Press the a button and register

the TV channel to a Programme
number (PR)

The normal EDIT menu is resumed.

LANGUAGE

The LANGUAGE setting which was
performed in the “Initial settings” (page 6)
can be changed.

1 Choose LANGUAGE, then press

the a or 3 button

A sub-menu of the LANGUAGE function
appears.

> LANGUAGE

OK

D0002-EN

2 Press the 5 and 6 buttons to

choose a language. Then press the
a button

PICTURE TILT

There are cases where the Earth’s magnetic
force may make the picture tilt or make
unnatural colours appear in the corner of the
screen. If this happens, you can correct it.

1 Choose PICTURE TILT, then press

the a or 3 button

The sub-menu of the PICTURE TILT
function appears.

> PICTURE TILT

OK

D0018-EN

2 Press the 6 buttons until the

picture becomes level. Then press
the a button

DECODER (EXT-2)

If you have a decoder connected to a T-V
LINK compatible VCR, which in turn is
connected to the EXT-2 terminal, use the
DECODER (EXT-2) function to unscramble
the scrambled TV channels.

1 Turn on the decoder power

2 Display the scrambled TV channel

on the TV

Even if the decoder is working, a
scrambled picture appears.

ENGLISH

3 Display the SET UP menu and

choose DECODER (EXT-2)

SET UP

AUTO PROGRAM
EDIT/MANUAL
LANGUAGE
PICTURE TILT
DECODER(EXT-2)
COMPONENT AUTO SELECT
EXT SETTING

OK

D0029-EN

ON
ON

37

SET UP menu

4 Press the 5 buttons to choose

ON

An unscrambled picture appears.

To cancel the DECODER (EXT-2)
function:

Press the 5 buttons to choose OFF.

5 Press the a button to complete

the setting

The T-V LINK menu appears.

T-V LINK

DOWNLOAD TV RECORDING DEVICE

OK

D0005

EXIT

-EN

You can send the programme numbers
data to a VCR with the T-V LINK
function.

6 Turn on the VCR, and then press

the a button to transmit the data
to VCR

The T-V LINK menu disappears once the
data transmission ends.

If the DECODER (EXT-2) function has
been set to “ON” but the TV channel
cannot be unscrambled, check the
following:

• Has the decoder been connected to the
VCR properly according to the VCR
and decoder instruction manuals?

• Has the decoder power been turned
on?

• Can the TV channel be unscrambled
with a decoder?

• Do you need to change the VCR
settings in order to connect the
decoder? Confirm that the VCR is set
properly by rechecking the VCR
instruction manual.

COMPONENT AUTO SELECT

When a external device that can output a
component signal is connected to the EXT-4
component terminal and the connected
device is played back, the TV input is
automatically changed to EXT-4.

ON:

When the device connected to EXT-4 is
played back, the TV input is automatically
changed to EXT-4.

OFF:

Even when the device connected to EXT-4 is
played back, the TV input is not changed.
(Set to OFF when shipped from the factory.)

• This function automatically changes the
TV input to EXT-4 when the TV detects a
component input signal from the device
connected to the EXT-4.

• When set to ON, the TV input may be
automatically changed to EXT-4 just by
an operation such as turning the power on,
removing a disc, or another operation
with a device (such as a DVD player).

38

SET UP menu

EXT SETTING

1 Choose EXT SETTING, then press

the a or 3 button

The EXT SETTING menu appears.

> EXT SETTING

EXT-1

EXT-3

EXT-5

TV

OK

D0020-EN

2 Follow the instructions for the

function you want to use and
operate the function

S-IN:

You can enjoy the high-quality picture of
the 2 S-VIDEO signal (Y/C signal).

ID LIST:

You can have a name for each of the
devices connected for each EXT terminal.

DUBBING:

You can choose a signal source to be
output from an EXT-2 terminal.

 S-IN (S-VIDEO input)

You can connect a device (such as an S-VHS
VCR) to enjoy the high-quality picture of the
S-VIDEO signal (Y/C signal).

Preparation:

• First read the device’s instruction manual
and “Additional preparation” on page 42
to connect the device to the TV properly.
Second, follow the device’s instruction
manual to set the device so that it sends an
S-VIDEO signal (Y/C signal) to the TV.

• Do not set S-IN (S-VIDEO input) to an
EXT terminal connected to a device
which cannot output an S-VIDEO (Y/C
signal). If it is set wrongly, a picture
cannot appear.

DUBBING
EXT-2

EXT-4

ID LIST

S-IN

1 Press the 5 or 6 buttons to

choose an EXT terminal

> EXT SETTING

EXT-1

EXT-3

EXT-5

TV

OK

D0020-EN

DUBBING
EXT-2

EXT-4

ID LIST

S-IN

2 Press the yellow button and set the

S-IN (S-VIDEO input).
Then press the a button

An S-IN (S-VIDEO input) mark is
displayed. You can view an S-VIDEO
signal (Y/C signal) instead of the regular
video signal (composite signal).

To cancel the S-IN (S-VIDEO input)
setting:

Press the yellow button and turn off S-IN (S­VIDEO input) mark. The regular video
signal (composite signal) pictures are
resumed.

• The EXT-1 terminal does not support S­VIDEO signal (Y/C signal) and you
cannot set S-IN (S-VIDEO input) in the
EXT-1 terminal.

• Setting S-IN (S-VIDEO input) changes
the head character from “E” to “S”. When
an EXT terminal receives a normal video
signal, “E1”, “E2” or “E5” appears on the
display. This changes to “S1”, “S2” or
“S5” when it receives an S-VIDEO
signal.

• Even a device which can output an
S-VIDEO signal (Y/C signal) may output
a regular video signal (composite signal)
depending on the device setting. If a
picture cannot appear because the S-IN
(S-VIDEO input) setting has been made,
read the device instruction manual
carefully again to check for the device
settings.

ENGLISH

39

SET UP menu

 ID LIST

You can store a name for each of the devices
connected to each EXT terminal. Giving a
name to an EXT terminal makes the EXT
terminal number appear on the screen,
together with its name.

1 Press the 5 or 6 buttons to

choose an EXT terminal

2 Press the blue button to display the

name list (ID LIST)

> EXT SETTING

EXT-1

EXT-3

EXT-5

TV

OK

D0021-EN

DUBBING
EXT-2

EXT-4

3 Press the 6 buttons to choose a

name. Then press the a button

The ID LIST disappears and the name is
assigned to the EXT terminal.

• You cannot assign an EXT terminal
name not found in the name list (ID
LIST).

To erase a name assigned to the
EXT terminal:

Choose a blank space.

4 Press the a button to complete

the setting

ID LIST

VHS
S-VHS
DVC
CAM
SAT
STB
GAME
DVD
DVR

 DUBBING

You can choose a signal source to be output
from the EXT-2 terminal.

You can do this with the output signals of the
devices connected to other EXT terminals, or
with the picture and sound from a TV
channel you are currently viewing.

1 Press the 5 buttons to choose

the arrow from the menu

> EXT SETTING

EXT-1

EXT-3

EXT-5

TV

OK

D0022-EN

2 Press the 6 buttons to choose an

EXT terminal or TV.
Then press the a button

The arrow in the menu represents a signal
flow. The left side of the arrow shows a
signal source output from the EXT-2
terminal.

EXT-1/EXT-3/EXT-5:

The output signal of the device connected
to an EXT terminal passes through the TV
and is output from the EXT-2 terminal.

TV:

The picture and sound of the TV channel
you are currently viewing are output from
the EXT-2 terminal.

DUBBING
EXT-2

EXT-4

40

• During dubbing, you cannot turn off
the TV. Turning off the TV also turns
off the output from the EXT-2
terminal.

• When you choose an EXT terminal as
an output, you can view a TV
programme or a picture from the other
EXT terminal while dubbing the
picture from a device connected to the
EXT terminal onto a VCR connected
to the EXT-2 terminal.

• The RGB signals from TV games
cannot be output. Teletext programmes
cannot be output.

SET UP menu

ENGLISH

41

Additional preparation

Connecting external equipment

Connect the equipment to the TV, making the
correct rear panel and front panel connections.

Before connecting anything:

• Read the manuals that came with the
equipment.
Depending on the equipment, the
connection method may be different from
the diagram. Also, the equipment settings
may need to change depending on the
connection method.

• Turn off all the equipment including the TV.

• The “Specifications” on page 49 give the
details of the EXT terminals. If you are
connecting equipment not listed in the
following connection diagram, see the
table to choose the best EXT terminal.

• Connecting cables are not supplied.

• When a DVD player is connected to the
EXT-4 component terminal, the TV input
can be automatically changed to EXT-4
by just turning the power supply of the
connected device on. For details, see
“COMPONENT AUTO SELECT” in the
SET UP menu on page 38.

• If the VCR’s audio output is mono, connect
the VCR’s AUDIO OUT (audio output)
terminal and the TV’s EXT-5 audio L/
MONO terminal with an audio cable.

1 VCR (composite signal)
2 VCR (composite signal/S-VIDEO signal)
3 T-V LINK compatible VCR (composite

signal/S-VIDEO signal)

4 Decoder
5 DVD player (composite signal/S-VIDEO

signal)

6 DVD player (composite signal/RGB

signal)

7 DVD player (component video signals;

Y/Pb/Pr)

8 TV game (composite signal/RGB signal)
9 TV game (composite signal/S-VIDEO

signal)

0 Headphones

- Camcorder (composite signal/S-VIDEO

signal)

= SCART cable
~ Audio cable
! Video cable
@ S-VIDEO cable
# Component cable

Side of the TV

42

EXT-5

S

/

MONO

L

S

R

L

/

MONO

EXT-5

P

R

P

Back of the TV

EXT-

Y

PrPbR

4

L

L

R

AUDIO OUT

EXT-1

EXT-2

S

EXT-3

S

Additional preparation

 Equipment which can output the

S-VIDEO signal (Y/C signal) such
as an S-VHS VCR

Connect the equipment to an EXT terminal.
You can choose between an S-VIDEO signal

(Y/C signal) and a regular video signal
(composite signal). For details of how to
operate the equipment, see “S-IN (S-VIDEO
input)” on page 39.

 T-V LINK compatible VCR

Be sure to connect the T-V LINK compatible
VCR to the EXT-2 terminal. If not, the T-V
LINK function will not work properly.

• When connecting a T-V LINK compatible
VCR to the EXT-2 terminal, be sure to
connect the decoder to the VCR. If not,
the T-V LINK function may not work
properly. After you have stored TV
channels in the programme numbers (PR)
list, set the DECODER (EXT-2) function
for the programme number (PR) to ON to
unscramble a scrambled TV channel. For
details, see “EXT SETTING” on page 39.

 Connecting headphones

Connect the headphones with a stereo mini­jack (3.5 mm diameter) to the headphone
socket at the TV rear panel.

• No sound comes from the TV speakers
when the headphones are connected.

 Video or sound signal output from

the EXT-2 terminal

You can change over the output of the video/
sound signal from the EXT-2 terminal. This
is useful when you want to dub the video/
sound from another device onto the VCR
connected to the EXT-2 terminal. For details
on how to do this, see “DUBBING” on
page 40.

• The signals from EXT-4 terminal cannot
be output from EXT-2.

 TV output from the EXT-1 terminal

The video/sound signal of a TV channel you
are viewing is always output from the EXT-1
terminal.

• Changing over a programme number (PR)
also changes over the TV output from the
EXT-1 terminal.

• The video/sound signal from an EXT
terminal cannot be output.

• Teletext programmes cannot be output.

 Connecting speakers/amplifier

While referring to the audio equipment
connection diagram, connect the audio
equipment you want to the TV.
You can use external front speakers to listen
to the TV sound instead of the TV speakers.

Before connecting anything:

• Read the manuals provided with the
amplifier and speakers.

• Turn the TV and amplifier off.

• To prevent magnetism from the speakers
adversely effecting the TV screen, use
magnetic-shielded speakers for the front
speakers.

• Note that connecting cables are not
supplied.

Back of the TV

L

AUDIO OUT

R

1 Amplifier
2 Front speakers (Magnetic-shielded type)

L

• The output from the AUDIO OUT
terminal is not interrupted by headphone
connection to the TV. You cannot cut the
sound from the front speaker even if you
connect a headphone to the TV.

• Adjust the volume of the external
speakers with the amplifier.

R

ENGLISH

43

CH/CC numbers

When you want to use the INSERT function on page 36, find the CH/CC number corresponding to
the Channel number of the TV channel from this table.

CH Channel

CH 02 / CH 202 E2, R1

CH 03 / CH 203 E3, ITALY A

CH 04 / CH 204 E4, ITALY B, R2

CH 05 / CH 205 E5, ITALY D, R6

CH 06 / CH 206 E6, ITALY E, R7

CH 07 / CH 207 E7, ITALY F, R8

CH 08 / CH 208 E8, R9

CH 09 / CH 209 E9, ITALY G

CH 10 / CH 210 E10, ITALY H, R10

CH 11 / CH 211

CH 12 / CH 212

CH 21 / CH 221 E21, R21

CH 22 / CH 222 E22, R22

CH 23 / CH 223 E23, R23

CH 24 / CH 224 E24, R24

CH 25 / CH 225 E25, R25

CH 26 / CH 226 E26, R26

CH 27 / CH 227 E27, R27

CH 28 / CH 228 E28, R28

CH 29 / CH 229 E29, R29

CH 30 / CH 230 E30, R30

CH 31 / CH 231 E31, R31

CH 32 / CH 232 E32, R32

CH 33 / CH 233 E33, R33

CH 34 / CH 234 E34, R34

CH 35 / CH 235 E35, R35

CH 36 / CH 236 E36, R36

CH 37 / CH 237 E37, R37

CH 38 / CH 238 E38, R38

CH 39 / CH 239 E39, R39

E11, ITALY H+1, R11

E12, ITALY H+2, R12

CH Channel

CH 40 / CH 240 E40, R40

CH 41 / CH 241 E41, R41

CH 42 / CH 242 E42, R42

CH 43 / CH 243 E43, R43

CH 44 / CH 244 E44, R44

CH 45 / CH 245 E45, R45

CH 46 / CH 246 E46, R46

CH 47 / CH 247 E47, R47

CH 48 / CH 248 E48, R48

CH 49 / CH 249 E49, R49

CH 50 / CH 250 E50, R50

CH 51 / CH 251 E51, R51

CH 52 / CH 252 E52, R52

CH 53 / CH 253 E53, R53

CH 54 / CH 254 E54, R54

CH 55 / CH 255 E55, R55

CH 56 / CH 256 E56, R56

CH 57 / CH 257 E57, R57

CH 58 / CH 258 E58, R58

CH 59 / CH 259 E59, R59

CH 60 / CH 260 E60, R60

CH 61 / CH 261 E61, R61

CH 62 / CH 262 E62, R62

CH 63 / CH 263 E63, R63

CH 64 / CH 264 E64, R64

CH 65 / CH 265 E65, R65

CH 66 / CH 266 E66, R66

CH 67 / CH 267 E67, R67

CH 68 / CH 268 E68, R68

CH 69 / CH 269 E69, R69

CC Channel

CC 01 / CC 201 S1

CC 02 / CC 202 S2

CC 03 / CC 203 S3

CC 04 / CC 204 S4

CC 05 / CC 205 S5

CC 06 / CC 206 S6

CC 07 / CC 207 S7

CC 08 / CC 208 S8

CC 09 / CC 209 S9

CC 10 / CC 210 S10

CC 11 / CC 211 S11

CC 12 / CC 212 S12

CC 13 / CC 213 S13

CC 14 / CC 214 S14

CC 15 / CC 215 S15

CC 16 / CC 216 S16

CC 17 / CC 217 S17

CC 18 / CC 218 S18

CC 19 / CC 219 S19

CC 20 / CC 220 S20

CC 21 / CC 221 S21

CC 22 / CC 222 S22

CC 23 / CC 223 S23

CC 24 / CC 224 S24

CC 25 / CC 225 S25

CC 26 / CC 226 S26

CC 27 / CC 227 S27

CC 28 / CC 228 S28

CC 29 / CC 229 S29

CC 30 / CC 230 S30

CC Channel

CC 31 / CC 231 S31

CC 32 / CC 232 S32

CC 33 / CC 233 S33

CC 34 / CC 234 S34

CC 35 / CC 235 S35

CC 36 / CC 236 S36

CC 37 / CC 237 S37

CC 38 / CC 238 S38

CC 39 / CC 239 S39

CC 40 / CC 240 S40

CC 41 / CC 241 S41

CC 75 / CC 275 X

CC 76 / CC 276 Y, R3

CC 77 / CC 277 Z, ITALY C, R4

CC 78 / CC 278 Z+1, R5

CC 79 / CC 279 Z+2

CH Channel

CH 102 F2

CH 103 F3

CH 104 F4

CH 105 F5

CH 106 F6

CH 107 F7

CH 108 F8

CH 109 F9

CH 110 F10

CH 121 F21

CH 122 F22

CH 123 F23

CH 124 F24

CH 125 F25

CH 126 F26

CH 127 F27

CH 128 F28

CH 129 F29

CH 130 F30

CH 131 F31

CH 132 F32

CH 133 F33

CH 134 F34

CH 135 F35

CH 136 F36

CH 137 F37

CH 138 F38

CH 139 F39

CH 140 F40

44

CH Channel

CH 141 F41

CH 142 F42

CH 143 F43

CH 144 F44

CH 145 F45

CH 146 F46

CH 147 F47

CH 148 F48

CH 149 F49

CH 150 F50

CH 151 F51

CH 152 F52

CH 153 F53

CH 154 F54

CH 155 F55

CH 156 F56

CH 157 F57

CH 158 F58

CH 159 F59

CH 160 F60

CH 161 F61

CH 162 F62

CH 163 F63

CH 164 F64

CH 165 F65

CH 166 F66

CH 167 F67

CH 168 F68

CH 169 F69

CC Frequency (MHz)

CC 110 116 - 124

CC 111 124 - 132

CC 112 132 - 140

CC 113 140 - 148

CC 114 148 - 156

CC 115 156 - 164

CC 116 164 - 172

CC 123 220 - 228

CC 124 228 - 236

CC 125 236 - 244

CC 126 244 - 252

CC 127 252 - 260

CC 128 260 - 268

CC 129 268 - 276

CC 130 276 - 284

CC 131 284 - 292

CC 132 292 - 300

CC 133 300 - 306

CC 141 306 - 311

CC 142 311 - 319

CC 143 319 - 327

CC 144 327 - 335

CC 145 335 - 343

CC 146 343 - 351

CC 147 351 - 359

CC 148 359 - 367

CC 149 367 - 375

CC 150 375 - 383

CC 151 383 - 391

CC Frequency (MHz)

CC 152 391 - 399

CC 153 399 - 407

CC 154 407 - 415

CC 155 415 - 423

CC 156 423 - 431

CC 157 431 - 439

CC 158 439 - 447

CC 159 447 - 455

CC 160 455 - 463

CC 161 463 - 469

CH/CC numbers

• When two CH/CC numbers correspond to one Channel number, choose either one according to
the current COUNTRY setting. When the COUNTRY setting is other than FRANCE, choose a
two-digit CH/CC number. When the COUNTRY setting is FRANCE, choose a three-digit CH/
CC number.

• Find the CH/CC number (CC110 to CC161) corresponding to the TV channel (SECAM-L
system) from a French cable TV station, based on the broadcast frequency of the TV channel.
When you do not know the broadcast frequency, please contact the cable TV station.

• The CH/CC numbers of CH102-CH169 and CC110-CC161 correspond to the TV channels
being broadcast by a SECAM-L system. The other CH/CC numbers correspond to the TV
channels being broadcast by a method other than a SECAM-L system.

ENGLISH

45

Troubleshooting

If a problem arises while you are using the TV, please read this troubleshooting guide carefully
before you ask to have the TV repaired. You may be able to fix it easily by yourself. For example,
if the mains plug is disconnected from the mains outlet, or the TV aerial has problems, you may
think there is a problem with the TV itself.

Important:

• This troubleshooting guide only covers problems whose causes are not easy to decide. If you
have a question when you are operating a function, read the page(s) for that function carefully,
not this troubleshooting guide.

• If you follow the advice in this troubleshooting guide without any success, unplug the mains
plug and ask for your TV to be repaired. Do not attempt to repair the TV by yourself or to
remove the rear cover of the TV.

 If you cannot turn on the TV

• Is the mains plug connected to the mains
outlet?

• Is the power lamp lit? If not, press the A
button.

• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV on when the VCR/TV/DVD
switch is set to the VCR or DVD position.

 If you cannot turn off the TV

• Make sure you set the VCR/TV/DVD
switch to the TV position. You cannot
turn the TV off when the VCR/TV/DVD
switch is set to the VCR or DVD position.

 No picture or no sound

• Have you chosen a TV channel with very
poor reception? If so, the BLUE BACK
function will be activated: the entire
screen becomes blue, and the sound is
muted. If you still want to view the TV
channel, follow the description “BLUE
BACK” on page 32 to change the BLUE
BACK function setting to OFF.

• If the SYSTEM setting for a TV channel
is incorrect, it may prevent the sound
from being issued. Follow the description
“EDIT/MANUAL” on page 33 to use the
MANUAL function to try to change the
SYSTEM setting.

 Poor picture

• If noise (snow) totally blocks out the
picture, there may be a problem with the
aerial or aerial cable. Check the following
to try to solve the problem:

– Have the TV and aerial been connected

properly?
– Has the aerial cable been damaged?
– Is the aerial pointing in the right

direction?
– Is the aerial itself faulty?

• If the TV or aerial suffers interference
from other equipment, stripes or noise
may appear in the picture. Move any
equipment such as an amplifier, personal
computer, or a hair drier, that can cause
interference away from your TV. Or try
moving the TV. If the aerial suffers
interference from a radio tower or high­voltage wire, please contact your local
dealer.

• If the TV suffers interference from signals
reflecting from mountains or buildings,
double-pictures (ghosting) will occur. Try
to change the aerial’s direction or replace
it with one with better directionality.

• Are your COLOUR SYSTEM settings
correct? Follow the description
“COLOUR SYSTEM” on page 27 to try
to solve the trouble.

• Have the COLOUR and BRIGHT settings
been adjusted properly? Follow the
description “BRIGHT” and “COLOUR”
on page 25 to try to adjust them properly.

46

Troubleshooting

• Videotaping teletext is not recommended
because it may not record correctly.

• When a white and bright still image (such
as a white dress) is displayed on the
screen, the white part may look as if it is
coloured. This is unavoidable due to the
nature of the picture tube itself, and not
due to a TV failure. When the picture
disappears from the screen, the unnatural
colours will also disappear.

• When viewing images from commercially
available video software products, or
videos from videotapes which have been
recorded improperly, the top of the image
may be distorted. This is due to the
condition of the video signal. There is
nothing wrong with the TV.

• Since this TV is designed to make full use
of the resolution of the original video
source, the motion may appear unnatural
when the video source is input with 625p
progressive-scanning component signals.
If this occurs, change the output setting of
the connected device to 625i interlace­scanning component signal output. See
the instructions that came with the device
for more information.

 Poor sound

• Have you adjusted BASS or TREBLE
properly? If not, follow the description
“BASS” or “TREBLE” on page 29.

• When TV channel reception is poor, it can
be hard to hear stereo or bilingual sound.
In this case, follow the description
“STEREO / I • II” on page 29 to hear the
sound more easily by changing it to a
mono sound.

 If the TV does not respond to the

remote control

• Have the batteries of the remote control
worn out? Follow the description “Putting
the batteries into the remote control” on
page 6 and replace them with new batteries.

• Have you attempted to use the remote
control from the sides or rear of the TV or
from more than seven metres away from the
TV? Use the remote control in front of your
TV or from less than seven metres away.

• When you are viewing a teletext
programme, you cannot operate the TV’s
menu. Press the b button to return to the
ordinary TV programme, and then try
operating the menus.

• If the TV suddenly stops responding,
press the A button on the TV and turn off
the TV. Press the A button again to turn
on the TV. If the TV returns to a normal
state, it is not a failure.

 Other issues

• When the SLEEP TIMER function
operates, the TV is automatically turned
off. If the TV suddenly turns off, try to
press the # (standby) button to turn on
the TV once again. If the TV goes back to
normal, there is no problem.

• When the TV is receiving a wide-screen
signal (WSS) or a signal from an external
device affecting the screen size, the
ZOOM mode automatically changes.
When you want to resume the previous
ZOOM mode, press the c button
again.

• If you bring magnetised equipment such
as a speaker near to your TV, the picture
may be warped or unnatural colours may
appear at the corners of the screen. In this
case, keep the equipment away from your
TV. If speakers cause this to happen, use
magnetically-shielded speakers instead.

ENGLISH

47

Troubleshooting

• It takes a short period of time from the
time an operation such as changing
channels is performed until an image is
displayed. This is not a fault. This is the
time needed for the image to stabilize
before it can be displayed.

• The TV may make a crackling sound due
to a sudden change in temperature. The
picture or sound may be normal. If you
hear crackling sounds frequently while
you are viewing the TV, there may be
other causes. As a precaution, ask your
service technician to inspect it.

• Touching the screen may cause you to
feel a slight electric shock due to its static
electricity. This is unavoidable due to the
construction of the picture tube. It is not a
problem with the TV. You can rest
assured that this static discharge is not
harmful.

• A picture may be tilted due to the
influence of the earth’s magnetism. In this
case, use the “PICTURE TILT” on
page 37 to complete the tilt.

• When set to 2-pictures multi, adjust the
headphone sound with HEADPHONE
VOLUME in the SOUND menu.

48

Specifications

Model HV-32P40BU HV-28P40BU

Broadcasting systems CCIR B/G, I, D/K, L
Colour systems PAL, SECAM

Channels and frequencies • E2-E12, E21-E69, S1-S41, X, Y, Z, Z+1, Z+2, ITALY A-H, ITALY H+1, ITALY

Sound-multiplex systems A2 (B/G, D/K), NICAM (B/G, I, D/K, L) system
Teletext systems FLOF (Fastext), TOP, WST (World Standard System)
Power requirements 220 - 240 V AC, 50 Hz
Power consumption 147 W, Standby: 2.0 W 130 W, Standby: 2.0W
Picture tube size Viewable area 76 cm

Audio output Rated Power output: 10 W + 10 W
Speakers (13 cm × 6.5 cm) oblique
EXT-1 terminal Euroconnector (21-pin, SCART)

EXT-2 terminal Euroconnector (21-pin, SCART)

EXT-3 terminal Euroconnector (21-pin, SCART)

EXT-4 terminal RCA connectors × 5

EXT-5 terminal RCA connectors × 3

AUDIO OUT terminal RCA connectors × 2

Headphone jack Stereo mini-jack (3.5 mm in diameter)
Dimensions (W × H × D) 864 mm × 587 mm × 550 mm 762 mm × 528 mm × 493 mm
Weight 52.0 kg 39.0 kg
Accessories Remote control unit × 1 (RM-C1812S)

We may change the design and specifications without notice.

Pictures displayed on the screen using this TV’s ZOOM functions should not be shown for any
commercial or demonstration purpose in public places (cafes, hotels, etc.) without the consent of
the owners of copyright of the original picture sources, as this would be an infringement of
copyright.

• The EXT terminals also support the NTSC 3.58/4.43 MHz system.

H+2, F2-F10, F21-F69, R1-R12, R21-R69

• French cable TV channel of broadcast frequencies 116 - 172 MHz and 220 ­469 MHz

(measured diagonally)

• Video input, Audio L/R inputs and RGB inputs are available.

• TV broadcast outputs (Video and Audio L/R) are available.

• Video input, S-VIDEO (Y/C) input, Audio L/R inputs and RGB inputs are
available.

• Video and Audio L/R outputs are available.

• T-V LINK functions are available.

• Video input, S-VIDEO (Y/C) input and Audio L/R inputs are available.

• Component video (Y, Pb, Pr) input and Audio L/R inputs are available.

• 625p, 525p, 1125i signals are available.

• Some DVD players can output 625p, 525p signals.

• 1125i are new high-definition signals. However, 1125i broadcasts are currently
not available in Europe.

S-VIDEO connector × 1

• Video input, S-VIDEO (Y/C) input and Audio L/MONO and R inputs are
available.

• Audio L/R outputs are available.

• Output level 0.5 Vrms.

AA/R6 dry cell battery × 2

Viewable area 66 cm
(measured diagonally)

ENGLISH

49

50

© 2004 Victor Company of Japan, Limited

LCT1684-001A-U
0804-T-CR-JMUK