JVC HR-VP636U(C) Instructions Manual

Download

Page 1

HR-VP636U

VIDEO CASSETTE RECORDER

INSTRUCTIONS

PU30425-1787

For Customer Use:

Enter below the Serial No. which is located on the rear of cabinet. Retain this information for future reference.  Model No. HR-VP636U



Serial No.

POWER

REW



PLAY

VIDEO (MONO) L – AUDIO – R

REC

STOP/EJECT PAUSE

HMS

ITR TIMER

VIDEO

SP EP

AM PM

REC

SAP

PAUSE

PLAY

POWER

ENTER

PLAY

STOP

OSD

DAILY (M-F)

AUX

C.RESET

CH SKIP

CANCEL

TV VOL.

SP/EP

DISPLAY TV/VIDEO

CABLE

VCR

TIMER

WEEKLY

12453

807

SHUTTLE

PLUS

MULTI BRAND

REMOTE CONTROL UNIT

REW

REC

PAUSE

ADD

w Channel

Changer

Cable

Page 2

Dear Customer,

Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR.

CAUTIONS

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

This video cassette recorder should be used with AC 120V`, 60Hz only. To prevent electric shocks and fire hazards, DO NOT use any other power source.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.

CAUTION



RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Failure to heed the following precautions may result in damage to the VCR, remote control or video cassette.

1. DO NOT place the VCR . . .

... in an environment prone to extreme temperatures or

humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are

generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT block the VCR’s ventilation openings.

3. DO NOT place heavy objects on the VCR or remote control.

4. DO NOT place anything which might spill on top of the VCR or remote control.

5. AVOID violent shocks to the VCR during transport.

**MOISTURE CONDENSATION

Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR’s power turned on for a few hours to let the moisture dry.

**ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

n Cassettes marked "VHS" (or "S-VHS") can be used with this

video cassette recorder. However, only "VHS" recordings can be played back in this model.

n HQ VHS is compatible with existing VHS equipment.

CAUTION:

Changes or modifications not approved by JVC could void user's authority to operate the equipment.

VCR Plus+C3 and PlusCode are trademarks of Gemstar Development Corporation. The VCR Plus+C3 system is manufactured under licence from Gemstar Development Corporation.

Page 3

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A) Your product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B) Your product may be equipped with a 3-wire grounding-type

plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

• Do not block the openings by placing the product on a bed,

sofa, rug or other similar surface.

• Do not place the product in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION  810-20)

GROUNDING  CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

ELECTRIC SERVICE EQUIPMENT

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

GROUND CLAMP

ANTENNA INSTALLATION INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

Page 4

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the

product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation. e.If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.

HOW TO USE THIS INSTRUCTION MANUAL

● All major sections and subsections are listed in the Table Of

Contents on page 5. Use this when searching for information

on a specific procedure or feature.

● The Index on pages 55–57 lists frequently-used terms, and

the number of the first page on which they are used or

explained in the manual. This section also illustrates the

controls and connections on the front and rear panel, the

front display panel and the remote control.

● The Z mark signals a reference to another page for

instructions or related information.

● Operation buttons necessary for the various procedures are

clearly indicated through the use of illustrations at the

beginning of each major section.

BEFORE YOU INSTALL YOUR NEW VCR . . .

. . . please read the sections/literature listed below.

● ”Cautions” on page 2

● ”Important Products Safety Instructions” on the previous pages

USE

1. Accessories

To avoid personal injury:

• Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.

• Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.

• Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.

• Do not try to roll a cart with small casters across thresholds or deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

3. Water and Moisture

Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

4. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

PORTABLE CART WARNING (Symbol provided by RETAC)

Page 5

CONTENTS

TIMER RECORDING 37

VCR Plus+ Timer Programming ............ 37

Enter Program Information.............................. 37

Instant Timer Recording (ITR) ............... 39

On-Screen Timer Programming ........... 39

Check And Cancel Programs .......................... 41

Auto Timer ......................................................42

EDITING 43

Edit To Or From Another VCR ............... 43

Edit From A Camcorder ....................... 44

Assemble Editing .................................46

SPECIAL FEATURES 47

TV Multi-Brand Remote Control ..................... 47

Cable Box Multi-Brand Remote Control.......... 48

Control Two JVC VCRs ................................... 49

Child Lock ......................................................49

ROUBLESHOOTING 50

Power ................................................. 50

Tape Transport .....................................50

Playback .............................................50

Recording ............................................51

Timer Recording ...................................51

Other Problems....................................52

QUESTIONS AND ANSWERS 53

Playback .............................................53

Recording ............................................53

Timer Recording ...................................53

PECIFICATIONS 54

NDEX 55

List Of Terms ........................................55

Front View ...........................................56

Rear View ...........................................56

Front Display Panel ..............................57

Remote Control ....................................57

FOR SERVICING 58 WARRANTY 59

INSTALLING YOUR NEW VCR 6

Basic Connections .................................. 6

INITIAL SETTINGS 7

Dual Quick Set .......................................7

Clock .....................................................8

Preparation .......................................................8

Language Select ............................................... 8

Clock Setting .....................................................9

Semi-Auto ......................................................9

Manual ........................................................ 11

Auto ............................................................. 11

Tuner ...................................................12

Set Receivable Channels ................................ 12

Add Or Delete A Channel .............................. 14

Tuner And Cable Box Controller ........... 15

Situate And Connect Controller ...................... 15

Set Cable Box Output Channel ....................... 16

Set Cable Box Brand....................................... 17

VCR Plus+ Setup ..................................19

IMPLE PLAYBACK AND

RECORDING 22

Simple Playback ..................................22

Simple Recording .................................23

LAYBACK AND RECORDING FEATURES 24

Playback .............................................24

Still Picture...................................................... 24

Slow, Reverse, Reverse Slow Or Fast-Motion

Picture ............................................................ 24

Manual Tracking............................................. 25

Select The Soundtrack .................................... 26

Superimpose ...................................................27

Skip Search .....................................................28

Repeat Playback ............................................. 28

Index Search ...................................................28

Instant ReView ................................................29

Counter Reset .................................................. 29

Counter Memory ............................................ 29

Tape Position Indicator ................................... 30

Next-Function Memory .................................. 30

AV COMPU LINK Playback............................ 30

Active Video Calibration...................... 32

Preparation .....................................................32

Recording .......................................................33

Playback .........................................................34

Recording ............................................35

Record One Program While

Watching Another .......................................... 35

Display Elapsed Recording Time..................... 35

Stereo And SAP (Second Audio Program)........ 36

To Record SAP Programs ................................ 36

Page 6

INSTALLING YOUR NEW VCR

CHECK CONTENTS

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (Z pg. 54).

SITUATE VCR

Place the VCR on a stable, horizontal surface.

CONNECT VCR TO TV

The connection method you use depends on the type of TV you have.

RF Connection

●

To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV antenna from the TV. b– Connect the TV antenna cable to the ANT IN jack

on the rear of the VCR.

c– Connect the supplied RF cable between the RF

OUT jack on the rear of the VCR and the TV’s antenna terminal.

AV Connection

●

To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in

the illustration.

b– Connect an Audio/Video Cable (not supplied)

between the AUDIO OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV.

CONNECT VCR TO POWER SOURCE

Connect the power plug to an AC outlet.

● The clock will automatically be set when the antenna is connected and when the AC is first connected to the VCR (Z pg. 7).

FINAL PREPARATION FOR USE

Select the VCR channel (3 or 4) by setting the switch on the rear of the VCR as shown in the illustration.

Turn on the power to the TV. You are now able to perform simple playback (Z pg. 22) and recording (Z pg. 23). (If 'Auto' is displayed on the front display panel, the clock is being set automatically. Wait for the time to be displayed before powering on the VCR.)

NOTES:

●

The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3CH4 switch sets the VCR channel to CH3 or CH4.

●

The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area.

●

If your TV has no AV input terminals, set the channel on the TV to correspond to the CH3–CH4 switch on the back of the VCR.

●

Even if your TV has AV input terminals, you must connect it to the VCR using an RF cable in order to record one show while watching another (Z pg. 35).

●

For full identification of the VCR's rear panel, refer to the Index (REAR VIEW Z pg. 56).

Antenna or Cable

Flat Feeder

Coaxial Cable

Back of VCR

Maching Transformer

AC Outlet

RF OUT

RF Cable (provided)

75 ohm terminal

ANTENNA-IN (Antenna or Cable input)

AC Power Cord

CH3 CH4

AUDIO

VIDEO

Basic Connections

Back of VCR

Page 7

INITIAL SETTINGS

Dual Quick Set

IMPORTANT

● Don’t press any buttons on the VCR or remote during Dual Quick Set.

● If you perform Dual Quick Set successfully, there’s no need to perform the Clock (Z pg. 8) and Tuner (Z pg. 12) procedures. If, however, you want to add or delete channels, refer to “Add Or Delete A Channel” on page 14.

PERFORM DUAL QUICK SET

Make sure that the antenna cable is connected to the VCR. Then connect the VCR’s power plug to an AC outlet. For connection configuration, refer to “Basic Connections” (Z pg. 6). The clock and tuner channels will automatically be set.

● Auto clock set is performed first. AUTO is displayed on the Front Display Panel during Auto clock set. Auto Channel set is performed next. The channel numbers are displayed in ascending order during auto channel set. When Dual Quick Set has been completed successfully the correct time is displayed.

● The clock can be adjusted automatically by the Host PBS every hour on the hour (except for 11:00 PM, midnight, 1:00 AM and 2:00 AM) by the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the VCR’s power is turned off.)

● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semi-Auto procedure (Z pg. 9). Auto channel set (Z pg. 12) has already taken place and it need not be set again.

● If “- -:- -” appears on the display, your antenna cable may not be connected to the VCR, there may not be a Host PBS signal available in your area, or your cable box may not be set to the PBS channel. If everything is connected and set correctly, perform the Manual Clock Set procedure (Z pg. 11). Auto channel set has not yet taken place, so please also perform the “Set Receivable Channels” procedure (Z pg. 12).

With the antenna cable connected the Dual Quick Set function allows the clock and tuner to be set automatically when the power plug is first connected to an AC outlet.

The time and date can be set automatically from clock setting data that is transmitted by one of the regular TV broadcast channels. We call this TV channel the “Host Channel” and it is a PBS channel in your area.

The auto clock set function scans all the channels received by your VCR to find the clock setting data of the Host Channel.

The auto channel set function scans all the channels received by your VCR, then automatically assigns receivable channels to the CH

∞

buttons, and skips non-receivable channels.

ATTENTION CABLE BOX SUBSCRIBERS

If you perform the Dual Quick Set procedure . . .

● Select the PBS channel on your cable box before plugging your VCR’s power plug into the AC outlet. (If you have more than one PBS channel, you may have to select an alternative PBS channel if Dual Quick Set is not successful.)

● If there is no PBS channel in your area, perform the Manual Clock Set procedure (Z pg. 11).

● For automatic clock adjustment to take place the VCR's power must be off and the cable box must be set to the PBS channel at clock adjustment times.

● If you perform Dual Quick Set successfully, D.S.T. will be set to “AUTO”. At the D.S.T. adjustment time (Z pg. 10), your VCR's power must be off and your cable box must be set to the host PBS channel in your area for the D.S.T. adjustment to take place. If the clock is not set correctly, change the D.S.T. setting to “ON” or “OFF. See step 6 of Semi-Auto procedure (Z pg. 9) or step 3 of Manual procedure (Z pg. 11).

During Auto Clock Set

During Auto Channel Set

The channels appear in ascending order, beginning with 1.

Dual Quick Set Completed

The current time (including AM/PM) is displayed.

Page 8

INITIAL SETTINGS (cont.)

Clock

POWER

MAIN MENU

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

VIDEO CALIBRATION

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

CH5∞

Preparation

TURN ON THE VCR

Press POWER. If watching channel 3 or 4, press TV/VIDEO to select the VIDEO mode. VIDEO is

displayed on the front display panel.

ACCESS ON-SCREEN MENU

Press MENU to bring up the Main Menu screen.

ACCESS CUSTOM SET SCREEN

At the Main Menu screen, place the arrow next to “CUSTOM SET” by pressing CH

∞

SHUTTLE PLUS

∞

, then

press OK.

Language Select

LANGUAGE SELECT

=ENGLISH

ESPAÑOL FRANCAIS

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

CUSTOM SET

OVERRIDE

AUTO CLOCK SET

=LANGUAGE SELECT

VCR PLUS+ SET-UP

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ACCESS LANGUAGE SELECT SCREEN

The messages are preset to appear in English. If you want to see them in Spanish or French, place the arrow next to “LANGUAGE SELECT” by pressing CH

∞

or SHUTTLE

PLUS

∞

, then press OK.

SELECT LANGUAGE

At the Language Select screen, place the arrow next to the desired language by pressing

∞

or SHUTTLE PLUS

∞

, then press MENU.

The Custom Set screen reappears.



12 45

3 6

8 0

 

TV/VIDEO

SHUTTLE PLUS 5∞

POWER

CH5∞

Page 9



12 45

3 6

8 0

 

SHUTTLE PLUS

Clock Setting

This step must be performed before going on to Auto, Semi-Auto or Manual clock setting procedures (each starts from step 2).

ACCESS MODE SELECT SCREEN

Place the arrow at the Custom Set screen next to “OVERRIDE AUTO CLOCK SET” by pressing

∞

or SHUTTLE PLUS

∞

, then press OK.

CUSTOM SET

=OVERRIDE

AUTO CLOCK SET LANGUAGE SELECT VCR PLUS+ SET-UP

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

Semi-Auto

SELECT MODE

At the Override Auto Clock Set screen, place the arrow next to “SEMIAUTO CLOCK SET” by pressing CH▲▼ or

SHUTTLE PLUS

∞

, then

press OK.

ACCESS SELECT SCREENS

At the Semi-Auto Clock Set screen, place the arrow next to the desired mode by pressing CH▲▼ or SHUTTLE PLUS

∞

then press OK.

To select the Host Channel — step 4 To select the Time Zone — step 5 To select the D.S.T. mode — step 6

SELECT HOST CHANNEL

You can either select “AUTO”, or enter a PBS channel number. For automatic channel selection, simply press MENU. To manually select the PBS channel, press the appropriate NUMBER key, CH▲▼ or SHUTTLE PLUS

∞

to cycle through the channel numbers (hold button

down to speed through numbers) and stop when the desired number appears. Press MENU and the SemiAuto Clock Set screen reappears.

NOTE:

There are some PBS channels that do not transmit clock setting data.

OVERRIDE AUTO CLOCK SET

AUTO CLOCK SET

=SEMI-AUTO CLOCK SET

MANUAL CLOCK SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

SEMI-AUTO CLOCK SET

=HOST CHANNEL SELECT

TIME ZONE SELECT D.S.T. SELECT

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

HOST CHANNEL SELECT

(CATV)

CH AUTO

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

CONTINUED ON NEXT PAGE.

NUMBER

Page 10



12 45

3 6

8 0

 

SELECT TIME ZONE

You can either select “AUTO”, or select the correct zone. If you selected "AUTO" in step 4 and if you live near the boundary of an adjacent time zone, or receive cable TV channels, a PBS channel from a different time zone may become your host channel. Therefore, in this case make sure to manually select the correct time zone. Place the arrow next to your choice by pressing CH

∞

or SHUTTLE PLUS

∞

, then press

MENU to return to the Semi-Auto Clock Set screen.

SELECT D.S.T. MODE

You have three choices: a–Select “AUTO” and the adjustment to your VCR’s clock will be made according to the incoming signal from the host channel. b–Select “ON” and the adjustment will be made based on the clock itself. c–Select “OFF” if Daylight Saving Time doesn’t apply to you.

Place the arrow next to your choice by pressing

∞

or SHUTTLE PLUS

∞

, then press MENU and

the Semi-Auto Clock Set screen reappears.

SHUTTLE PLUS

INITIAL SETTINGS (cont.)

TIME ZONE SELECT

=AUTO MOUNTAIN

ATLANTIC PACIFIC EASTERN ALASKA CENTRAL HAWAII

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

D.S.T. SELECT

=AUTO

ON OFF

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

IMPORTANT

After performing the Semi-Auto clock set procedure, make sure that the VCR is off before the next hour so that the clock can be set. (The clock is automatically adjusted on the hour except at 11:00 PM, midnight, 1:00 AM and 2:00 AM.)

**AUTO DAYLIGHT SAVING TIME

This function enables automatic adjustment of the VCR’s clock at the start and end of Daylight Saving Time. With Auto DST activated, . . . . . . on the first Sunday of April at 2:00 AM, the clock is adjusted

to 3:00 AM.

. . . on the last Sunday of October at 2:00 AM, the clock is

adjusted to 1:00 AM.

Page 11



12 45

3 6

8 0

 

NUMBER

SHUTTLE PLUS

Manual

SELECT MODE

At the Override Auto Clock Set screen, place the arrow next to “MANUAL CLOCK SET” by pressing CH▲▼ or SHUTTLE PLUS

∞

, then press OK.

SET DATE, TIME AND D.S.T.

The Manual Clock Set screen is displayed and the first setting that can be set begins flashing. Press the appropriate NUMBER keys to set the date and time (if only 1 digit, press "0" first). Press CH▲▼ or SHUTTLE PLUS

∞

to set AM/PM and D.S.T. (Daylight Saving Time) to “ON” (automatic adjustment based on VCR’s clock) or “OFF” (if D.S.T. doesn’t apply to you). Press OK after AM/PM and D.S.T. settings. The next setting that can be set begins flashing. When you’re finished with this set-up procedure, press MENU to start the clock.

NOTE:

∞

and SHUTTLE PLUS

∞

can be used to perform

all operations. (In this case, press OK after each setting.)

MAKE CORRECTIONS

To change any of the settings, press OK or SHUTTLE PLUS ™ £ until the item you want to change blinks, then set as in step 3.

MANUAL CLOCK SET

DATE 1/ 1/96 MON TIME – – : – – AM D.S.T. ON

PRESS NUMBER KEY(0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

SELECT MODE

At the Override Auto Clock Set screen, place the arrow next to “AUTO CLOCK SET” by pressing CH

∞

SHUTTLE PLUS

∞

, then press MENU as many times

as necessary to return to the normal screen.

Auto

Auto need only be selected if Semi-Auto or Manual had previously been selected.

Page 12

Tuner

Set Receivable Channels

TURN ON THE VCR

Press POWER. If watching on channel 3 or 4, press TV/ VIDEO to select the VIDEO mode. VIDEO is displayed

on the front display panel.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS TUNER SET SCREEN

Place the arrow next to "TUNER SET" by pressing

∞

or SHUTTLE PLUS

∞

, then press OK.

ACCESS BAND SCREEN

Place the arrow next to "BAND" by pressing

∞

or SHUTTLE PLUS

∞

, then press OK.

SET FREQUENCY BAND

If you receive your TV channels from an external antenna, select "TV". If you receive your TV channels from a cable TV system, select "CATV". Place the arrow next to your choice by pressing

∞

or SHUTTLE PLUS

∞

, then press MENU to return to the Tuner Set screen.

BAND

=CATV

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

TUNER SET

=BAND

AFC AUTO CHANNEL SET MANUAL CHANNEL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END



12 45

3 6

8 0

 

TV/VIDEO

SHUTTLE PLUS

POWER

INITIAL SETTINGS (cont.)

Page 13

PERFORM AUTO CHANNEL SET

Place the arrow next to "AUTO CHANNEL SET" by pressing CH

∞

SHUTTLE PLUS

∞

, then

press OK. Receivable channels in your area are automatically assigned to the CH

∞

buttons, and non-receivable channels are skipped.

NOTES:

●

At the end of Auto Channel Set, “SCAN COMPLETED” appears on screen.

●

If the scan was unsuccessful, “SCAN COMPLETED– NO SIGNAL” appears on screen. Check the band setting and connections and start again.

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

AUTO CHANNEL SET

(TV)

CH 2 ADD

SCANNING ...

PRESS (MENU) TO END



12 45

3 6

8 0

 

SHUTTLE PLUS

Page 14

Add Or Delete A Channel

ACCESS TUNER SET SCREEN

Access by performing steps 2 and 3 of the Tuner procedure on page 12.

● To add a channel, go to step 2.

● To delete a channel, skip to step 4.

ACCESS AFC SCREEN

Place the arrow next to "AFC" by pressing CH

∞

SHUTTLE PLUS

∞

, then press OK.

MAKE SELECTION

Place the arrow next to "SPCL" by pressing CH

∞

or SHUTTLE PLUS

∞

then press MENU to return to the Tuner Set screen.

ACCESS MANUAL CHANNEL SET SCREEN

Place the arrow next to "MANUAL CHANNEL SET" by pressing CH

∞

or SHUTTLE PLUS

∞

, then press OK.

STORE DESIRED CHANNEL

Input the channel number using the NUMBER keys or by pressing CH

∞

SHUTTLE PLUS

∞

, then

press ADD to add or CH.SKIP to delete. Repeat for each channel you want to store or skip.

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

AFC

NORM

=SPCL

PRESS (5,∞) TO SELECT PRESS (MENU) TO END



12 45

3 6

8 0

 

NUMBER

CH.SKIP

ADD

SHUTTLE PLUS

MANUAL CHANNEL SET

(CATV)

CH 125 SKIP

SELECT CH NO. AND PRESS (ADD/SKIP) PRESS (MENU) TO END

INITIAL SETTINGS (cont.)

Page 15

This procedure is required if you receive your TV channels through a cable box (descrambler). The Cable Box Controller allows the VCR to automatically switch cable box channels, allowing you to timer-record programs from various cable stations. The Cable Box Controller is effective for recording shows that have been programmed using VCR Plus+ (Z pg. 37) or On-Screen Timer Programming (Z pg. 39).

Situate And Connect Controller

Tuner And Cable Box Controller

Suggested Location

Place the cable box on top of the VCR. Attach the VCR's Cable Box Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

SITUATE CONTROLLER

Place the Cable Box Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.

ATTACH CONTROLLER

Fasten securely using the supplied adhesive strips.

CONNECT CABLE BOX TO VCR

The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR.

If your cable box doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the cable box to the ANT.IN connector on the rear of your VCR.

NOTE:

Refer to your cable box’s instruction manual during connection.

CONNECT CONTROLLER TO VCR

Connect to the CABLE BOX connector on your VCR.

About Your Cable Box

This VCR has two separate methods to control your Cable Box.

●

The VCR's Wireless Remote Control Unit can control your Cable Box. This eliminates the need for a separate Cable Box Remote Control Unit.

●

The VCR's Cable Box Controller can also control your Cable Box. This allows the VCR to change your Cable Box's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 48.

CABLE

BOX

Cable box

Controller (suggested locations)

Cable box

Controller

Transmitter

Connected to ANT. IN

Connected to VIDEO/ AUDIO IN

Your VCR

Page 16

Set Cable Box Output Channel



12 45

3 6

8 0

 

SHUTTLE PLUS

POWER

TV/VIDEO

TURN ON THE VCR

Press POWER. If watching channel 3 or 4, press TV/ VIDEO to select the VIDEO mode. VIDEO is displayed

on the front display panel.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS CUSTOM SET SCREEN

Press CH

∞

or SHUTTLE

PLUS

∞

to place the

arrow next to “CUSTOM SET”, then press OK.

ACCESS VCR PLUS+ SET-UP SCREEN

Press CH

∞

or SHUTTLE

PLUS

∞

to place the

arrow next to “VCR PLUS+ SET-UP”, then press OK.

ACCESS CABLE BOX OUTPUT SCREEN

Press CH

∞

or SHUTTLE

PLUS

∞

to place the arrow next to “CABLE BOX OUTPUT”, then press OK.

CUSTOM SET

OVERRIDE

AUTO CLOCK SET

LANGUAGE SELECT

=VCR PLUS+ SET-UP

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

VCR PLUS+ SET-UP

GUIDE CHANNEL SET GUIDE GHANNEL MAP

=CABLE BOX OUTPUT

CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

MAIN MENU

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

VIDEO CALIBRATION

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

INITIAL SETTINGS (cont.)

Page 17

SELECT CABLE BOX OUTPUT CHANNEL

Your selection depends on how your cable box is connected to your VCR.

If your cable box is connected to your VCR using an RF connection . . .

. . . press CH

∞

SHUTTLE PLUS

∞

to place the arrow next to the channel number representing the cable box’s output (2–6).

If your cable box is connected to your VCR’s AUDIO/ VIDEO IN connectors . . .

. . . press CH

∞

or SHUTTLE PLUS

∞

to place the

arrow next to “ON LINE”.

RETURN TO VCR PLUS+ SET-UP SCREEN

Press MENU.

CABLE BOX OUTPUT

=OFF

ON CH2 ON CH3 ON CH4 ON CH5 ON CH6 ON LINE

PRESS (5,∞), TO SELECT

PRESS (MENU) TO END

TURN ON CABLE BOX

Select a channel other than channel 9 on your Cable Box.

ACCESS CABLE BOX BRAND SET SCREEN

At the VCR Plus+ Set-Up screen, press CH

∞

SHUTTLE PLUS

∞

to place the arrow next to “CABLE BOX BRAND SET”, then press OK.

ENTER CABLE BOX BRAND

Press the appropriate NUMBER keys to enter the Cable Box Code from the CABLE BOX BRAND LIST on page 18, then press ENTER.

● If the cable box’s

channel changes to 9, setting is complete.

● If there are more than one code number listed for

your brand of cable box, repeat step 3 until the cable box’s channel changes to 9.

● If you go through all listed code numbers and the

channel doesn’t change, try all other numbers between 1 and 101.

VCR PLUS+ SET-UP

GUIDE CHANNEL SET GUIDE GHANNEL MAP CABLE BOX OUTPUT

=CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END



12 45

3 6

8 0

 

SHUTTLE PLUS

NUMBER

Set Cable Box Brand

CABLE BOX BRAND SET

SELECT BRAND NO. AND PRESS (ENTER) PRESS (MENU) TO END

CONTINUED ON NEXT PAGE.

ENTER

Page 18

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

You can now set up the VCR Plus+ feature ( Z pg. 19).

CABLE BOX BRAND LIST

BRAND CODE

ARCHER 52, 53, 54, 85, 86 CABLEVIEW 85, 86 CITIZEN 85, 86 CURTIS 13, 14, 15, 16 DIAMOND 52, 53, 54 EAGLE 30, 31, 32, 33, 34, 35, 36, 37 EASTERN 51 GC BRAND 85, 86 GEMINI 55, 56 GENERAL ELECTRIC 67 GENERAL INSTRUMENTS 1, 2, 3, 4, 5, 6, 101 HAMLIN 23, 24 JERROLD 1, 2, 3, 4, 5, 6, 101 MACOM, HITACHI 57, 58, 59 MAGNAVOX 43, 44, 45, 46, 47, 48, 49 MOVIETIME 71, 72, 73 NSC 71, 72, 73 OAK 17, 18, 19, 20, 21, 22 PANASONIC 25, 26, 27 PHILIPS 38, 39, 40, 41, 42 PIONEER 7, 8 PULSER 85, 86 RCA 25, 26, 27 REGAL 78, 79, 80 REGENCY 51 SAMSUNG 74, 75, 76 SCIENTIFIC ATLANTA 13, 14, 15, 16 SL MARX 74, 75, 76 SPRUCER 25, 26, 27 STARGATE 74, 75, 76, 85, 86 SYLVANIA 70 TEKNIKA 68, 69 TELECAPTION 100 TELEVIEW 74, 75, 76 TEXSCAN 28, 29 TOCOM 62, 63, 64, 65, 66 UNIKA 52, 53, 54, 85, 86 UNIVERSAL 81, 82, 83, 84 VIDEOWAY 9, 10, 11, 12 VID TECH 89 VIDTER 89 VIEWSTAR 30, 31, 32, 33, 34, 35, 36, 37 ZENITH 9, 10, 11, 12



12 45

3 6

8 0

 

INITIAL SETTINGS (cont.)

NOTES:

●

Although the supplied Cable Box Controller is compatible with many different cable box brands, it is possible that it will not work with your cable box.

●

If your cable box doesn’t respond to any code between 1 and 101, you can’t use the Controller to change cable box channels. In this case, make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording. Please contact your cable company about the possibility of exchanging your current cable box with one that is compatible with your VCR.

●

The VCR can only change the cable box channel through the Cable Box Controller during timer recording.

●

If your cable box is one that can’t be operated with a remote control (has no remote sensor), you can’t use the Cable Box Controller to change its channels. Make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording.

●

If you are unable to set the Cable Box Controller, please contact JVC toll free at 1-800-252-5722.

Page 19

The VCR Plus+ timer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the PlusCode number for the TV program you wish to record (found in most TV listings) and the VCR’s timer is automatically programmed.

Depending on the TV or cable stations that you receive and the channel numbers that they are received on in your area, you may have to make certain changes in your VCR’s “Guide Channel Set” menu to get proper results. Please read the following information carefully to find out which tasks you need to perform.

Before VCR Plus+ setup you must have performed the following procedures:

● Dual Quick setting (Z pg. 7)

Clock setting (Z pg. 8) Tuner setting (Z pg. 12)

● Tuner and cable box setting if you receive your TV channels through a cable box (Z pg. 15)

Channel Number Matching

Most TV listings have a chart indicating the “Guide Channel” number assigned to each station for purposes of VCR Plus+ programming. Check the chart in your TV listings and see if the Guide Channel numbers listed for the stations you receive are the same as the channel number on which each is received by your VCR or cable box.

**SPECIAL NOTES FOR CABLE SUBSCRIBERS**

● In many instances, cable TV stations have VCR Plus+ Guide Channel numbers that DO NOT match the number of the channel on which you receive the station. Check your TV listings, or contact your cable supplier for details.

● Many normal broadcast TV stations can be viewed on cable. Check your TV listing, or contact your cable supplier for details.

If the numbers match, go directly to “VCR Plus+ Timer Programming” (Z pg. 37).

If the numbers are different, and you want to be able to timer record programs from those stations, you have to inform the VCR of the mismatch. Go to step 1. If timer recording on those stations is not important to you, you can go directly to “VCR Plus+ Timer Programming” (Z pg. 37).

VCR Plus+ Setup



12 45

3 6

8 0

 

TV/VIDEO

POWER

CONTINUED ON NEXT PAGE.

TURN ON THE VCR

Press POWER. If watching channel 3 or 4, press TV/ VIDEO to select the TV’s VIDEO mode. VIDEO is

displayed on the front display panel.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

Page 20

ACCESS CUSTOM SET SCREEN

Press CH

∞

or SHUTTLE

PLUS

∞

to place the

arrow next to “CUSTOM SET”, then press OK.

ACCESS VCR PLUS+ SET-UP SCREEN

Press CH

∞

or SHUTTLE

PLUS

∞

to place the

arrow next to “VCR PLUS+ SET-UP”, then press OK.

ACCESS GUIDE CHANNEL SET SCREEN

Press CH

∞

or SHUTTLE

PLUS

∞

to place the arrow next to “GUIDE CHANNEL SET”, then press OK.

INPUT GUIDE CHANNEL NUMBER

Press CH

∞

, SHUTTLE

PLUS

∞

or the appropriate NUMBER keys to input the Guide Channel number as shown in the TV listing. Then press OK.

● If you receive your

channels with a cable box and if you have properly set your Cable Box Controller, “CABLE CH” appears in place of “VCR CH”. If not, refer to pages 15–16 and re-perform the procedure.

MAIN MENU

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

VIDEO CALIBRATION

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

CUSTOM SET

OVERRIDE

AUTO CLOCK SET

LANGUAGE SELECT

=VCR PLUS+ SET-UP

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

VCR PLUS+ SET-UP

=GUIDE CHANNEL SET

GUIDE GHANNEL MAP CABLE BOX OUTPUT CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END



12 45

3 6

8 0

 

SHUTTLE PLUS

NUMBER

INITIAL SETTINGS (cont.)

GUIDE CHANNEL SET

GUIDE CH : VCR CH

1 : 1

PRESS NUMBER KEY (0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

Page 21

INPUT RECEIVING CHANNEL NUMBER

Press CH

∞

, SHUTTLE PLUS

∞

or the appropriate

NUMBER keys to input the number of the channel on which the Guide Channel’s broadcasts are received. Then press OK.

● If there is more than one mismatch, repeat steps 6 and 7

for each instance.

RETURN TO VCR PLUS+ SET-UP SCREEN

Press MENU.

CHECK INPUT DATA

Press CH

∞

or SHUTTLE

PLUS

∞

to place the arrow next to “GUIDE CHANNEL MAP”, then press OK.

● The Guide Channel and

VCR or cable box channel numbers you input appear on the screen in ascending order. Check to ensure you’ve entered them correctly.

● If you entered more than

10 sets of numbers, press OK to see the next set of numbers.

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

VCR PLUS+ SET-UP

GUIDE CHANNEL SET

=GUIDE GHANNEL MAP

CABLE BOX OUTPUT CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

GUIDE CHANNEL MAP

GUIDE: VCR GUIDE : VCR

6 :47 10 :55 12 :41 15 :38 33 :28 67 :49

PRESS (OK) TO NEXT PRESS (MENU) TO END



12 45

3 6

8 0

 

SHUTTLE PLUS

NUMBER

You can now use VCR Plus+ for quick and simple timer programming (Z pg. 37).

Page 22



12 45

3 6

8 0

 

SIMPLE PLAYBACK AND RECORDING

LOAD A CASSETTE

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Don’t apply too much pressure when inserting.

● The VCR’s power comes on automatically.

● If watching channel 3 or 4, press TV/VIDEO to select

the VIDEO mode. VIDEO is displayed on the front display panel.

● The counter is automatically reset to "0H 00M 00S".

● If the cassette's record safety tab has been removed,

playback begins automatically.

FIND PROGRAM START POINT

If the tape is advanced past the start point, press REW. To go forward, press FF.

START PLAYBACK

Press PLAY. "VIDEO CALIBRATION" appears on screen (Z pg. 34).

STOP PLAYBACK

Press STOP or STOP/EJECT. Then press STOP/EJECT to remove the cassette.

Simple Playback

Usable cassettes

Full-Size VHS T-30 (ST-30**) T-60 (ST-60**) T-90 T-120 (ST-120**) T-160 (ST-160**) ST-210**

Compact VHS* TC-20 (ST-C20**) TC-30 (ST-C30**) TC-40 (ST-C40**)

* Compact VHS camcorder recordings can be played on

this video recorder. Simply place the recorded cassette into a VHS Cassette Adapter and it can be used just like any full-sized VHS cassette.

** This video recorder can record on regular VHS and

Super VHS cassettes. However, it will record and play back regular VHS signals only. It is not possible to play back Super VHS recordings.

FF (Fast-Forward)

PLAY

REW (Rewind)

FF (Fast-Forward)

REW (Rewind)

STOP

STOP/EJECT

PLAY

TV/VIDEO

Page 23

Simple Recording



12 45

3 6

8 0

 

NUMBER

SP/EP

PAUSE

STOP

REC

PLAY

PAUSE

REC

STOP/EJECT

PLAY

Accidental erasure prevention

● To prevent accidental recording on a recorded cassette, remove its record safety tab. To record on it later, cover the hole with adhesive tape.

Record safety tab

LOAD A CASSETTE

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape before inserting the cassette.

SELECT RECORDING CHANNEL

Press CH5∞. Or press the appropriate NUMBER keys, then press ENTER. (The channel changes after a few seconds whether you press ENTER or not.)

SET TAPE SPEED

Press SP/EP to set the recording speed.

START RECORDING

Press and hold REC and press PLAY on the remote control, or press REC on the VCR's front panel.

Active Video Calibration takes place at the beginning of both the first SP and the first EP recording after inserting the cassette (Z pg. 33).

PAUSE/RESUME RECORDING

Press PAUSE. Press PLAY to resume recording.

STOP RECORDING

Press STOP or STOP/EJECT. Then press STOP/EJECT to remove the cassette.

ENTER

Page 24

PAUSE DURING PLAYBACK

Press PAUSE. If there is vertical jitter, press CH5 or

∞

on the VCR's front panel or remote to stabilize the picture.

FRAME-BY-FRAME PLAYBACK

Advance the tape one frame by pressing PAUSE again.

● To control the direction of Frame-by-Frame playback,

press SHUTTLE PLUS ™ or £ during still picture mode.

RESUME NORMAL PLAYBACK

Press PLAY during still picture mode.

Playback

Still Picture

Slow, Reverse, Reverse Slow Or Fast-Motion Picture

DURING PLAYBACK

Press SHUTTLE PLUS ™ or £.

● To increase the speed in the forward direction, press £.

● To decrease the speed in the forward direction, press ™.

● To play in reverse slow motion, and in reverse play mode, continue to press ™ after selecting all the forward slow motion modes.

Press FF for forward fast motion, or REW for reverse fast motion.

RESUME NORMAL PLAYBACK

Press PLAY.

NOTES:

●

Press and hold FF or REW for more than 2 seconds for short fast-motion searches. When the button is released, normal playback resumes.

●

If noise bars appear during playback or slow motion, correct using manual tracking. (Z pg. 25).



12 45

3 6

8 0

 

REW

PLAY

PAUSE

REW

SHUTTLE PLUS ™/£

PAUSE

PLAY

PLAYBACK AND RECORDING FEATURES

Page 25

Manual Tracking

Once playback begins, the VCR’s automatic tracking function is engaged. If noise appears in the picture, you can override this and make the adjustment manually.

ENGAGE MANUAL TRACKING MODE

During playback, press the CH

∞

buttons on the VCR's front panel simultaneously to cancel the automatic tracking mode and enable manual tracking adjust.

ADJUST MANUAL TRACKING

Press CH

∞

on the VCR's front panel or remote. Press lightly for fine adjust, or press and hold for coarse adjust. Watch the screen and continue adjusting until optimum picture and sound quality are achieved.

RE-ENGAGE AUTOMATIC TRACKING

Press the CH

∞

buttons on the VCR's front panel

simultaneously.

● When automatic tracking is re-engaged, video

calibration is automatically activated.

NOTE:

During slow-motion playback, simply press CH5 or ∞ on the VCR's front panel or remote to adjust tracking.



12 45

3 6

8 0

 

Page 26

Select The Soundtrack

Your VCR can record two soundtracks simultaneously (Normal and Hi-Fi) and play back the selected one, or both together.

ACCESS MAIN MENU SCREEN

Press MENU during playback or when VCR is in stop mode.

● If the VCR Plus+ screen appears press MENU again.

ACCESS FUNCTION SET SCREEN

Place the arrow next to "FUNCTION SET" by pressing

∞

or SHUTTLE PLUS

∞

, then press OK.

ACCESS AUDIO MONITOR SCREEN

Place the arrow next to "AUDIO MONITOR" by pressing CH

∞

SHUTTLE PLUS

∞

, then

press OK.

SELECT MODE

You have three choices:

a– Hi-Fi b– Normal c– Mix

Place the arrow next to your choice by pressing

∞

or SHUTTLE

PLUS

∞

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

NOTE:

If the tape being played back has no Hi-Fi soundtrack, the Normal soundtrack will be heard no matter what choice you make at the Audio Monitor screen.



12 45

3 6

8 0

 

SHUTTLE PLUS

PLAYBACK AND RECORDING FEATURES (cont.)

FUNCTION

AUTO TIMER

SUPERIMPOSE 2ND AUDIO

=AUDIO MONITOR

AUX INPUT SPECIAL FUNCTION

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

AUDIO MONITOR

=HI-FI

NORM MIX

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

Page 27

Superimpose

This function, switchable between ON and OFF, determines whether or not operational indicators will appear on screen.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS FUNCTION SET SCREEN

Place the arrow next to "FUNCTION SET" by pressing CH

∞

or SHUTTLE PLUS

∞

, then press OK.

ACCESS SUPERIMPOSE SCREEN

Place the arrow next to "SUPERIMPOSE" by pressing CH

∞

SHUTTLE PLUS

∞

, then

press OK.

SELECT MODE

Place the arrow next to "ON" or "OFF" by pressing

∞

or SHUTTLE

PLUS

∞

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

NOTE:

If you engage the Record Pause mode, RECORD/PAUSE is displayed whether "SUPERIMPOSE" is set to "ON" or "OFF".



12 45

3 6

8 0

 

OSD

SHUTTLE PLUS

The superimposed indication on the TV screen tells you what the VCR is doing.

CH 125 RECORD THU 12:00 AM PAUSE

] SP

INDEX-1 NORM MEMORY OFF HI–FI COUNT –1:23:45

Tuned-in channel or AUX(iliary) mode

When the channel is changed, the new

channel is displayed on the screen for 5

seconds.

Clock time

Tape position indicator

Operation mode

When the operation mode is changed, the new mode is displayed — RECORD (5 sec.), PLAY (5 sec.), FF/REW (5 sec. when engaged from Stop mode), RECORD PAUSE (for as long as Pause is engaged), and ITR *:** (5 sec.).

+++

"Cassette Loaded" mark

When a cassette is loaded, the mark is

displayed for 5 seconds. It blinks when the

VCR's EJECT button is pushed. Audio mode indicators

Tape speed indicator

Counter memory on/off

INDEX indication

Counter reading

To recall an indication

1 Press OSD.

n All indications corresponding to the current status are

displayed for 5 seconds, leaving the counter information, and RECORD/PAUSE if in the Record Pause mode, on the screen. (No indication during still and search.)

2 Press OSD again to clear the display.

FUNCTION

AUTO TIMER

=SUPERIMPOSE

2ND AUDIO AUDIO MONITOR AUX INPUT SPECIAL FUNCTION

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

SUPERIMPOSE

=ON

OFF

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

Page 28

Skip Search

Repeat Playback

START REPEAT

Press and hold PLAY (until "PLAY" blinks on the front display panel) during playback, then release.

● The entire tape is played back 20 times.

STOP REPEAT

To stop, press STOP at any time.

NOTE:

Pressing PLAY, REW, FF, PAUSE or SHUTTLE PLUS

™

or £ also stops Repeat Playback.

Index Search

This function seeks out index codes that are placed on the tape at recording start.

START SEARCH

While the tape is stopped, press SHUTTLE PLUS ™ or £.

ACCESS DISTANT CODE

To access a recording 2–9 index codes away, press SHUTTLE PLUS ™ or £ repeatedly until the correct number is displayed on screen (only if SUPERIMPOSE is set to ON (Z pg. 27). Playback begins automatically when the desired recording is located.

● To find the very beginning of the desired program,

press REW or FF and search visually for the start point.

VIDEO

PLAY

HMS



12 45

3 6

8 0

 

PLAY

STOP

SKIP OVER UNWANTED SECTIONS

Press SKIP SEARCH 1 to 4 times during playback. Each press initiates a 30-second period of fast- motion playback. Normal playback resumes automatically.

NOTE:

To return to normal playback during a Skip Search, press PLAY.

REW

PLAY

REW

PLAYBACK AND RECORDING FEATURES (cont.)

SHUTTLE PLUS

SKIP SEARCH

PAUSE

Page 29

Instant ReView

At the press of a button, you can power up your VCR, rewind the tape and begin viewing the most recent timer-recorded program.

ACTIVATE INSTANT REVIEW

After ensuring that the VCR is off and the Timer mode is disengaged, press REVIEW.

● The power comes on and the VCR searches for the index code indicating the start of the last timer-recorded program, then begins playback automatically.

● You can access a program 2–9 index codes away from the current position on the tape. If, for example, you have 5 programs recorded and you want to watch the third one, press REVIEW three times.

● To find the very beginning of the desired program, press REW or FF and search visually for the program’s start point.



12 45

3 6

8 0

 

REW

REVIEW

DISPLAY

REW

C.RESET

C.MEMORY

STOP

RESET COUNTER TO ZERO

Press C.RESET.

NOTE:

By pressing the DISPLAY button, you can change the display to show the counter reading, channel number or clock time. (Channel number is not displayed during playback.)

Counter Memory

When activated, this feature returns the tape to counter position “zero”.

ACTIVATE COUNTER MEMORY

Press C.RESET during playback at a point you want to have quick access to later. The counter reads “0H 00M 00S”.

Then press C.MEMORY. The Counter Memory indicator in the front display panel lights.

RETURN TO COUNTER POSITION ZERO

Press STOP (during playback), then press REW. The tape rewinds and stops at approximately “0H 00M 00S” automatically.

● To cancel Counter Memory, press C.MEMORY.

Counter Reset

Page 30

COUNT 0:33:27

Tape Position Indicator

The Tape position indicator appears on screen when, from the stop mode, you press FF, REW or perform an Index Search or Instant ReView. The position of " " in relation to "B" (Beginning) or "E" (End) shows you where you are on the tape.

NOTE:

"SUPERIMPOSE" must be set to "ON", or the indicator will not appear (Z pg. 27).

Next-Function Memory

The Next Function Memory “tells” the VCR what to do after rewinding. * Before continuing, ensure that the VCR is in stop mode.

a– For Automatic Start Of Playback After Tape Rewind . . . . . . press REW, then press PLAY within 2 seconds. b– For Automatic Power Off After Tape Rewind . . . . . . press REW, then press POWER within 2 seconds. c– For Automatic Timer Standby After Tape Rewind . . . . . . press REW, then press TIMER within 2 seconds.

NOTE:

If you want the "next function" to automatically start when the counter reads "0H 00M 00S" (instead of at the beginning of the tape), press C. MEMORY so that the counter memory indicator appears on the front display panel before pressing REW or FF.

+++



12 45

3 6

8 0

 

REW

PLAY

POWER

REW

TIMER

PLAYBACK AND RECORDING FEATURES (cont.)

PLAY

AV COMPU LINK Playback

Your VCR is compatible with JVC’s AV COMPU LINK components, including amplifiers (or receivers) and televisions. AV COMPU LINK provides one touch control of the audio and video components that are linked via their AV COMPU LINK connectors.

For example: simply load a cassette in the VCR and press PLAY and the AV COMPU LINK components automatically power on, the TV's VIDEO mode is selected and the VCR goes into play mode. (PLAY need not be pressed if the cassette's record safety tab is removed.)

MAKE CONNECTION

Connect your VCR to an AV COMPU LINK component as shown in the illustration on page 31.

● The AV COMPU LINK cable is a mono 3.5 mm miniplug to mono 3.5 mm mini-plug connector.

TURN ON THE VCR

Press POWER.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

C.MEMORY

Page 31

ACCESS FUNCTION SET SCREEN

Press CH

∞

or SHUTTLE PLUS

∞

to place the arrow

next to “FUNCTION SET”, then press OK.

ACCESS SPECIAL FUNCTION SCREEN

Press CH

∞

or SHUTTLE

PLUS

∞

to place the arrow next to “SPECIAL FUNCTION”, then press OK.

ENABLE AV COMPU LINK PLAYBACK

Press CH

∞

or SHUTTLE

PLUS

∞

to place the arrow

next to “AV COMPU LINK”.

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

PERFORM AV COMPU LINK PLAYBACK

Simply insert a cassette and press PLAY (if the cassette’s record safety tab has been removed, playback begins automatically). Linked components are turned on, and the TV set to its VIDEO mode, automatically!

NOTE:

Connection varies depending on the type of JVC TV you have. Please refer to the TV’s instruction manual when making this connection.

PLAY



12 45

3 6

8 0

 

SHUTTLE PLUS

PLAY

AV COMPU LINK

Television

Your VCR

AV COMPU LINK

AV COMPU LINK II

(VCR ONLY)

VIDEO

OUT

AV COMPU LINK Cable (not supplied)

VIDEO IN

AUDIO IN

Example

AUDIO OUT

FUNCTION AUTO TIMER SUPERIMPOSE 2ND AUDIO AUDIO MONITOR AUX INPUT

=SPECIAL FUNCTION

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

SPECIAL FUNCTION

PAUSE

=AV COMPU-LINK

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

Page 32

Active Video Calibration

Your VCR is equipped with the Active Video Calibration feature, which checks the condition of the tape in use during recording and playback, and compensates to provide the highest-possible recording and playback pictures. *The default setting for both recording and playback is "ON".

Preparation



12 45

3 6

8 0

 

POWER

TV/VIDEO

SHUTTLE PLUS

TURN ON THE VCR

Press POWER. If watching channel 3 or 4, press TV/ VIDEO to select the VIDEO mode. VIDEO is displayed

on the front display panel.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS VIDEO CALIBRATION SCREEN

Press CH5∞ or SHUTTLE PLUS

∞

to place the arrow next to “VIDEO CALIBRATION”, then press OK.

SELECT MODE

Place the arrow next to "ON" by pressing CH5

∞

or SHUTTLE PLUS

∞

then press OK to move the arrow to the Playback section. Set Playback to "ON", then press MENU as many times as necessary to return to the normal screen. (Pressing OK returns the arrow to the Recording section.)

MAIN MENU

PROGRAM SET FUNCTION SET TUNER SET CUSTOM SET

=VIDEO CALIBRATION

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ACTIVE VIDEO CALIBRATION

RECORDING = ON

OFF

PLAYBACK = ON

OFF

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

PLAYBACK AND RECORDING FEATURES (cont.)

Page 33

Recording

Perform steps 1 – 3 on page 23 ("Simple Recording") before continuing.



12 45

3 6

8 0

 

REC

PLAY

PAUSE

ATTENTION:

n As calibration takes place before recording actually starts,

there is a delay of about 7 seconds after REC and PLAY on the remote, or REC on the VCR's front panel, are pressed. To make sure you record the desired scene or program completely, first perform the following steps:

1) Press and hold PAUSE, and press REC to engage the

RECORD PAUSE mode.

● The VCR then automatically checks the condition of the tape and, after about 7 seconds, re-enters RECORD PAUSE.

2) Press PLAY to start recording. n If you want to bypass Active Video Calibration and start

recording right away, set "RECORDING" to "OFF" in step 4 of the Preparation procedure (Z pg. 32).

PLAY

START END

ACTIVE VIDEO CALIBRATION

DURING CALIBRATION

START END

ACTIVE VIDEO CALIBRATION

CALIBRATION COMPLETE

START RECORDING

Press and hold REC and press PLAY on the remote control, or press REC on the VCR's front panel.

● The VCR takes about 7 seconds to assess the quality of the tape in use, then recording begins with the picture level optimized.

NOTES:

●

Calibration occurs immediately prior to both the first SP and the first EP recording after inserting the cassette. It does not take place during recording.

●

In the case of timer recording, calibration takes place for both SP and EP before the first timer recording after inserting the cassette (regardless of the tape speed selected for that recording).

●

Once the cassette is ejected, the calibration data is canceled. The next time the cassette is used for recording, calibration is re-performed.

●

During Active Video Calibration, all other functions are disabled.

●

While Active Video Calibration is operative, the PAUSE button will not function.

●

SUPERIMPOSE must be set to "ON" or the Active Video Calibration screen will not appear (Z pg. 27).

+++

Page 34

Playback

The VCR assesses the quality of the tape once you initiate playback.

Before beginning, perform steps 1 and 2 on page 22.



12 45

3 6

8 0

 

PLAY

START PLAYBACK

Press PLAY.

● The VCR adjusts the playback picture quality based on the quality of the tape in use.

NOTES:

●

When using rental tapes, or tapes recorded on other VCRs, set “PLAYBACK” in step 4 of the Preparation procedure to either “ON” or “OFF” as desired (Z pg. 32).

●

The Video Calibration screen only appears at the beginning of automatic tracking. Even though the screen doesn't appear after that, the Active Video calibration function is operative.

●

“SUPERIMPOSE” must be set to "ON" or the Video Calibration screen will not appear (Z pg. 27).

VIDEO CALIBRATION

PLAYBACK AND RECORDING FEATURES (cont.)

Page 35

Record One Program While Watching Another

ENGAGE TV MODE

During recording...

● If using the RF connection (Z pg. 6), press TV/VIDEO. The VCR's VIDEO indicator goes out and the TV broadcast being recorded disappears.

● If using the AV connection (Z pg. 6), change the TV's input mode from AV to TV.

SELECT CHANNEL FOR VIEWING

Use the TV’s channel selector to set the channel you want to watch.

Display Elapsed Recording Time

RESET COUNTER TO ZERO

Before recording starts, press C.RESET. The counter resets to zero and displays the exact elapsed time as the tape runs.

DISPLAY ELAPSED TIME ON SCREEN

During recording, press OSD at any time to see the elapsed time. All indications corresponding to the current status of the VCR are displayed for 5 seconds. The counter display remains on the screen indicating the elapsed time. Press OSD again to remove the display.

● Make sure "SUPERIMPOSE" is set to "ON" (Z pg. 27).

Recording



12 45

3 6

8 0

 

OSD

TV/VIDEO

C.RESET

Page 36



12 45

3 6

8 0

 

SHUTTLE PLUS

Stereo And SAP (Second Audio Program)

Your VCR’s built-in MTS decoder enables reception of Multichannel TV Sound broadcasts.

● The ST indicator on the front display panel lights during stereo broadcast reception, and SAP lights during SAP program reception.

● Both indicators light when a stereo program is accompanied by SAP audio.

To Record Stereo Programs . . .

. . . simply follow the basic recording procedure.

To Listen To Stereo Soundtrack During Recording . . .

. . . select "HI-FI" at the Audio Monitor screen (Z pg. 26).

To Record SAP Programs . . .

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS FUNCTION SET SCREEN

Place the arrow next to "FUNCTION SET" by pressing

∞

or SHUTTLE PLUS

∞

, then press OK.

ACCESS 2ND AUDIO SCREEN

Place the arrow next to "2ND AUDIO" by pressing

∞

or SHUTTLE PLUS

∞

, then press OK.

SELECT MODE

Place the arrow next to "ON" by pressing CH

∞

or SHUTTLE PLUS

∞

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

NOTES:

●

If a SAP program is received, the SAP audio is recorded on both the Normal and Hi-Fi tracks. The main audio program is not recorded.

●

If a non-SAP program is received, the main audio is recorded on both the Hi-Fi and Normal audio tracks.

2ND AUDIO

=ON

OFF

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

PLAYBACK AND RECORDING FEATURES (cont.)

Page 37

VCR Plus+ Timer Programming



12 45

3 6

8 0

 

NUMBER

NUMBER "9"

NUMBER "8"

TV/VIDEO

CANCEL

TIMER RECORDING

Enter Program Information

VCR PLUS+

PRESS NUMBER KEY(0-9) PRESS (MENU) TO MAIN MENU

CONTINUED ON NEXT PAGE.

Before VCR Plus+ Timer programming, see "VCR Plus+ Setup" on page 19.

LOAD A CASSETTE

Make sure the record safety tab is present.

● The VCR’s power comes on automatically.

● If you’re watching on channel 3 or 4, press TV/VIDEO

to select the VIDEO mode. VIDEO is displayed on the front display panel.

ACCESS VCR PLUS+ SCREEN

Press MENU.

● The clock must be set in order to access the VCR Plus+ screen. If you haven’t set the clock, the Main Menu screen appears when you press MENU. Refer to page 7 for the Dual Quick Set procedure or page 8 for the clock setting procedure.

ENTER PLUSCODE NUMBER

Press the appropriate NUMBER keys to enter the PlusCode number printed in the TV listings for the TV program you wish to record, then press OK. The Program screen appears.

● To make corrections, press CANCEL and input the correct PlusCode number.

● If the PlusCode number you input is incorrect, "ERROR" may appear on the screen to advise you of the error. This happens when the PlusCode number is for a program which has already passed. "ERROR" is displayed for about 4 seconds and the VCR Plus+ screen reappears (step 2).

CHECK INPUT DATA

The PlusCode number you entered appears in the Program screen. Check to make sure it’s accurate.

● To timer-record daily or weekly serials, press DAILY (NUMBER “8”) or WEEKLY (NUMBER “9”). “DAILY” or “WEEKLY” appears on the Program screen.

● If you made a mistake, press CANCEL and, after pressing MENU as many times as necessary to access the VCR Plus+ screen, input the correct PlusCode number.

PROGRAM 1

(VCR PLUS+ 12345678) DATE 7/10 FRI START 8:00 PM STOP 9:00 PM CHANNEL 8 SP

PRESS (8=DAILY, 9=WEEKLY

SP/EP=REC SPEED)

PRESS (MENU) TO END

Page 38

TIMER RECORDING (cont.)



12 45

3 6

8 0

 

TIMER

SHUTTLE PLUS

SET TAPE SPEED

Press SP/EP.

CHECK/CORRECT INPUT DATA

If the data is correct as it is, go to step 7. If not, press OK or SHUTTLE PLUS ™£ until the item you

want to change begins to blink. Then press the appropriate NUMBER keys, CH

∞

or SHUTTLE PLUS

∞

to obtain the desired setting.

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

● Press just once to access the Auto Timer screen (Z pg. 42).

ENGAGE TIMER MODE

Press TIMER. The VCR turns off automatically.

NOTES:

●

To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.

●

In case of a power failure after programming, the VCR’s memory backup keeps your selections for 10 minutes.

●

When timer-recording cable channels received through a Cable Box, be sure to keep the Cable Box set to ON.

SP/EP

NUMBER

Page 39

Instant Timer Recording (ITR)

This easy method lets you record for from 30 minutes to 6 hours (selectable in 30-min. increments), and shuts the VCR off after recording is finished.

START RECORDING

Press REC.

ENGAGE ITR MODE

Press REC again. ITR blinks and 0:30 appears on the front display panel.

SET RECORDING DURATION

If you want to record for more than 30 minutes, press REC to extend the time. Each press extends recording time by 30 minutes.

NOTES:

●

You can only perform ITR using the REC button on the VCR's front panel.

●

After you set the time, the previous display reappears.

●

To check remaining recording time, press REC once during recording and the remaining time is displayed for about 5 seconds. Be careful not to press again during this 5 seconds, or you’ll add 30 more minutes to the recording.

REC

ITR

VIDEO

REC

LOAD A CASSETTE

Make sure the record safety tab is intact. If not, cover the hole with adhesive tape, then load.

● The VCR comes on, and the counter is reset, automatically.

ACCESS PROGRAM SET SCREEN

Press MENU as many times as necessary to bring up the Main Menu screen, then press OK.

You can directly program the VCR’s timer to record up to 8 shows, as far as a year in advance. Remember, the clock must be set before you can program the timer (Z pg. 7 or 8).

On-Screen Timer Programming

* Refer to the illustration on page 40.

PROGRAM 1

DATE - - / - START - - : - - AM STOP - - : - - AM CHANNEL - - SP

PRESS NUMBER KEY(0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

CONTINUED ON NEXT PAGE.

Page 40

TIMER RECORDING (cont.)



12 45

3 6

8 0

 

NUMBER

NUMBER "9"

NUMBER "8"

TIMER

SHUTTLE PLUS

SELECT PROGRAM NUMBER

Press the appropriate NUMBER keys or CH

∞

SHUTTLE PLUS

∞

to select a vacant program number,

then press OK. The first time you do this, all numbers will be vacant, so just press OK when the screen appears.

SET PROGRAM INFORMATION

Press the appropriate NUMBER keys to set the date, start/stop time and channel number. Press CH

∞

SHUTTLE PLUS

∞

to set AM/PM and tape speed.

Then press OK after AM/PM, channel number and tape speed settings. The next setting that can be set begins flashing.

● Any information comprised of 1 digit (except the channel number) should have a "0" entered before it.

● It is possible to set all information using the CH

∞

SHUTTLE PLUS

∞

buttons. (In this case, press OK

after each setting.)

NOTE:

If you are using a cable box, enter the cable box channel, not the channel to be recorded. The channel to be recorded must be selected on the cable box. (The cable box channel is the VCR's channel that displays the chennels received by the cable box.)

** You can record selected programs at the same time

every weekday, or once a week. Before entering the month, press NUMBER key “8” (DAILY) or “9” (WEEKLY). Either "DAILY" or "WEEKLY" appears. Press again and "DAILY" or "WEEKLY" disappears.

MAKE CORRECTIONS

To change any of the settings, press OK or SHUTTLE PLUS ™ £ until the item you want to change begins blinking. Then set as in step 4.

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

● Press just once to access the Auto Timer screen (Z pg. 42).

ENGAGE TIMER MODE

Press TIMER. The VCR turns off automatically.

NOTES:

●

To disengage the timer before recording starts, press TIMER again. Pressing once more re-engages it.

●

In case of a power failure after programming, the VCR’s memory backup keeps your selections for 10 minutes.

●

If you select "PROGRAM SET" without having set the date and time, an error message appears. Follow its instructions.

●

If you enter a start time that has already passed, "ERROR" appears on the screen and flashes.

●

Programs that start after midnight must have the next day’s date.

●

After timer recording is completed, the VCR’s power goes off automatically.

●

You can program the timer while a regular recording is in progress; the on-screen menu will not be recorded.

●

If the end of tape is reached during timer recording, the cassette is automatically ejected.

●

When timer-recording cable channels received through a Cable Box, be sure to keep the Cable Box set to ON.

EXAMPLE

If you program the VCR to timer record a show on September 6 on channel 40 from 12:00 noon to 1:00 PM in SP mode, the screen will look like this:

PROGRAM 1

DATE 9/ 6 SUN START 12:00 PM STOP 1:00 PM CHANNEL 40 SP

PRESS NUMBER KEY(0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

Page 41

DISENGAGE TIMER

Press TIMER, then press POWER.

ACCESS PROGRAM SET SCREEN

Press MENU, then press OK.

CHECK PROGRAM INFORMATION

Press CH

∞

or SHUTTLE PLUS

∞

to check the

programs in succession.

Check And Cancel Programs

CANCEL A PROGRAM

Press CANCEL.

● Repeat steps 3 and 4 as many times as necessary.

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary. If there are still programs remaining, go to step 6.

RE-ENGAGE TIMER

Press TIMER again.



12 45

3 6

8 0

 

POWER

TIMER

CANCEL

SHUTTLE PLUS

To Cancel A Program . . .

Page 42

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS FUNCTION SET SCREEN

Place the arrow next to "FUNCTION SET" by pressing

∞

or SHUTTLE PLUS

∞

, then press OK.

ACCESS AUTO TIMER SCREEN

Place the arrow next to "AUTO TIMER" by pressing

∞

or SHUTTLE PLUS

∞

, then press OK. Now

skip to step 2 of the procedure below.

Or, during on-screen timer programming ...

ACCESS AUTO TIMER SCREEN

In step 7 in the VCR Plus+ Timer Programming procedure (Z pg. 38) or in step 6 in the On-Screen Timer Programming procedure (Z pg. 40), press MENU.

SELECT MODE

Place the arrow next to your choice ("ON" or "OFF") by pressing CH

∞

or SHUTTLE PLUS

∞

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

NOTE:

For safety, when AUTO TIMER is set to “OFF”, all other VCR functions are disabled while the Timer mode is engaged. To disengage the timer, press TIMER.



12 45

3 6

8 0

 

SHUTTLE PLUS

TIMER RECORDING (cont.)

Auto Timer

When activated, this function automatically engages the timer when the VCR's power is turned off, and disengages it when the power is turned on.

AUTO TIMER

=ON

OFF

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

TIMER

Page 43

Edit To Or From Another VCR

You can use your VCR as the player or the recorder.

MAKE CONNECTIONS

Connect an AV cable (not supplied) between the player’s VIDEO OUT and AUDIO OUT connectors and the recorder’s VIDEO IN and AUDIO IN connectors.

● When using your VCR as the recorder and a monaural VCR as the player, connect the player’s AUDIO OUT connector to the AUDIO IN L connector on the recorder.

LOAD CASSETTES

Insert the playback cassette into the player and the cassette to be recorded on into the recorder.

SET RECORDER’S INPUT MODE

Set to AUX. With this VCR, press NUMBER key “0” (AU appears on the front display panel in place of a channel number).

NOTE:

When using this VCR as the recorder, make sure to select "FRONT" or "REAR" (depending on which input connectors you use) at the Aux Input Screen. (To select the correct AUX input connector, follow steps 4, 5, 9 – 11 from the "Edit From A Camcorder" section, Z pg. 44.)

START PLAYER

Set to its play mode.

START RECORDER

Set to its record mode.

Player

Your VCR

AUDIO OUT

VIDEO OUT

VIDEO IN

AUDIO IN

Another VCR

Recorder

EDITING



12 45

3 6

8 0

NUMBER "0"

Page 44

EDITING (cont.)

Edit From A Camcorder

You can use a camcorder as the player and your VCR as the recorder.

MAKE CONNECTIONS

Connect an AV cable (not supplied) between the camcorder’s VIDEO OUT and AUDIO OUT connectors and your VCR’s VIDEO IN and AUDIO IN connectors.

● When a Master Edit Control-equipped JVC camcorder is used, the camcorder is capable of controlling your VCR. The editing cable is a mono 3.5 mm mini-plug to mono 3.5 mm mini-plug connector.

LOAD A CASSETTE

Insert the cassette to be recorded on into the recorder.

SET RECORDER’S INPUT MODE

Press NUMBER key “0” to set to AUX.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS FUNCTION SET SCREEN

Press CH

∞

or SHUTTLE PLUS

∞

to place the arrow

next to “FUNCTION SET”, then press OK.

If you’re using a JVC Master Edit Control-equipped camcorder — step 6 If not — step 9

ACCESS SPECIAL FUNCTION SCREEN

Press CH

∞

or SHUTTLE PLUS

∞

to place the arrow

next to “SPECIAL FUNCTION”, then press OK.

SELECT MODE

Press CH

∞

or SHUTTLE

PLUS

∞

to place the

arrow next to “PAUSE”.

RETURN TO FUNCTION SET SCREEN

Press MENU.

AUDIO IN

VIDEO IN

Camcorder

Player

VIDEO OUT

AUDIO OUT



12 45

3 6

8 0

 

NUMBER "0"

SHUTTLE PLUS

Recorder Your VCR

Editing cable (not supplied) (JVC camcorder only)

EDIT

To rear panel PAUSE/AV COMPU-LINK connector

SPECIAL FUNCTION

=PAUSE

AV COMPU-LINK

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

Page 45

ACCESS AUX INPUT SCREEN

Press CH

∞

or SHUTTLE PLUS

∞

to place the arrow

next to “AUX INPUT”, then press OK.

SELECT INPUT

If you are connecting the AV cable to the

AV connectors on the front of the VCR

, place the arrow

next to "FRONT" by pressing CH

∞

SHUTTLE PLUS

∞

. If you are connecting the AV cable to the

AV connectors

on the back of the VCR

, place the arrow next to "REAR"

by pressing CH

∞

or SHUTTLE PLUS

∞

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

START PLAYER

Set the camcorder to its play mode.

START RECORDER

Set your VCR to its record mode.

● If you are using a Master Edit Control-equipped JVC

camcorder, it can put the recorder automatically into Play mode. (Refer to camcorder's instruction manual.)



12 45

3 6

8 0

 

AUX INPUT

= FRONT

REAR

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

SHUTTLE PLUS

Page 46

Assemble Editing

Assemble Editing adds one recorded scene to another in succession. To use your VCR as the recorder ...

LOAD CASSETTES

Insert the original cassette in the player, and the recording cassette in the recorder.

SET TAPE SPEED

Set to "SP" or "EP" by pressing the SP/EP button on the remote control.

ENGAGE RECORDSTANDBY MODE

Press and hold PAUSE, and press REC.

FIND EDIT START POINT

Play back the original tape until you reach the scene to be edited.

START EDITING

When you reach the scene on the original tape to be edited, press PLAY to initiate the recorder’s record mode.

STOP EDITING

Press PAUSE to pause the tape in the recorder.

CONTINUE EDITING

Repeat steps 4 through 6 to add additional scenes.

NOTE:

Assemble Editing is also possible using your VCR as the playback deck.



12 45

3 6

8 0

 

PLAY

PAUSE

REC

PLAY

PAUSE

REC

SP/EP

EDITING (cont.)

Page 47

SPECIAL FEATURES

TV Multi-Brand Remote Control

The VCR's remote control can control several functions on JVC remote control TVs and on the brands of remote control TVs listed below.



12 45

3 6

8 0

 

POWER

NUMBER

ENTER

VOL. +/-

TV/VIDEO

STOP

TV/CABLE/VCR

TURN ON THE TV

Turn the power on using the TV's remote control.

SET REMOTE CONTROL MODE

Set the TV/CABLE/VCR switch on the VCR's remote control to TV.

SET TV BRAND CODE

Refer to the chart below. While holding down POWER, enter your TV’s brand code using the NUMBER keys, then press STOP.

● Once you have set the remote control to operate the

TV, you don’t have to repeat this step until you replace your remote control’s batteries.

● PANASONIC has two codes. If the TV does not

function with one code, try entering the other.

OPERATE TV

First, press POWER on the remote to see if the TV’s power goes off as it should. If it does, try other operations.

● The POWER, TV/VIDEO, CH

∞

, VOL +/– and

NUMBER keys on the remote can all be used to

operate the TV. *For some brands of TV, you must press ENTER after having pressed the NUMBER keys.

● To return the remote to VCR control, set the TV/

CABLE/VCR switch to VCR.

NOTE:

Depending on the kind of TV, there may be cases where some or all functions cannot be operated using the remote control.

TV BRAND NAME BRAND CODE

JVC 01 MAGNAVOX 02 MITSUBISHI 03 PANASONIC 04, 11 RCA 05 SHARP 06 SONY 07 TOSHIBA 08 ZENITH 09 HITACHI 10 SAMSUNG 12 SANYO 13

Page 48

Cable Box Multi-Brand Remote Control

The VCR's remote control can control functions on the brands of cable boxes listed below. Some cable box brands have more than one code. If your cable box does not function with a specified code, try other codes.



12 45

3 6

8 0

 

POWER

NUMBER

ENTER

STOP

TV/CABLE/VCR

SPECIAL FEATURES (cont.)

CABLE BOX BRAND NAME BRAND CODE

CURTIS 09, 10 GEMINI 08 GENERAL INSTRUMENTS 01, 02, 03, 04, 05, 06, 07, 08 HAMLIN 15, 16, 17, 18 JERROLD 01, 02, 03, 04, 05, 06, 07, 08 OAK 19, 20, 21 PANASONIC 24, 25, 26 PIONEER 13, 14 RCA 24, 25, 26 REGAL 15, 16, 17, 18 SAMSUNG 08, 13 SCIENTIFIC ATLANTA 09, 10 SIGMA 19, 20, 21 SL MARX 08, 13 SPRUCER 24, 25, 26 TELEVIEW 08, 13 TOCOM 22, 23 VIDEOWAY 11, 12 ZENITH 11, 12

TURN ON THE CABLE BOX

Turn the power on using the cable box’s remote control.

SET REMOTE CONTROL MODE

Set the TV/CABLE/VCR switch on the VCR’s remote control to CABLE.

ENTER CABLE BOX BRAND

While holding down POWER, use the NUMBER keys to enter the cable box brand number from the chart below and then press STOP.

● Once you have set the remote control to operate the

cable box, you don't have to repeat this step until you replace the remote control's batteries.

OPERATE CABLE BOX

First, press POWER to see if the cable box’s power goes off as it should. If it does, try other functions (CH

∞

and the NUMBER keys can be used to operate the cable box).

● For some brands of cable box, you must press ENTER

after having pressed the NUMBER keys.

● To return the remote to VCR control, set the TV/

CABLE/VCR switch to VCR.

NOTES:

●

You must set the cable box brand for your remote control and the cable box brand for your Cable Box Controller (Z pg. 17) individually. Cable box brands available for the remote control differ from those available for the Cable Box Controller.

●

It is possible that the remote control will not operate your cable box even if the cable box’s channels automatically change during timer recording using the Cable Box Controller.

Page 49

Control Two JVC VCRs

The supplied remote control is capable of controlling two JVC VCRs independently using the A/B CODE switch. You can set this VCR so it responds to remote commands only when the switch is set to B, and another VCR so it responds to commands when the switch is set to A. The switch is preset to A because this VCR normally responds to A-code signals. You can easily modify this VCR to accept B-code commands.



12 45

3 6

8 0

 

POWER

TIMER

A/B CODE

UNPLUG VCR'S POWER CORD

Unplug from the AC outlet.

SET A/B CODE SWITCH

Set the A/B CODE switch on the remote control to B.

PLUG IN POWER CORD

Plug back in to the AC outlet.

TURN VCR POWER ON

Press POWER on the remote.

The VCR will now respond only to B-code commands.

Child Lock

This feature allows you to prevent the operation of the VCR.

TURN VCR POWER ON

Press POWER.

ENGAGE CHILD LOCK

Press and hold POWER on the remote control until the Child Lock indicator ("—") appears on the front display panel.

● To cancel Child Lock, press and hold POWER on the

remote to turn the VCR on. During timer recording, pressing TIMER also cancels Child Lock.

NOTES:

●

When Child Lock is engaged, make sure to keep the remote control out of the reach of children.

●

Timer recording can be performed while Child Lock is engaged. The feature remains in effect after the recording is finished.

Page 50

TROUBLESHOOTING

Before requesting service for a problem, use this chart and see if you can repair the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your VCR off for repair.

POWER

POSSIBLE CAUSE

● The power cord is disconnected.

● The TIMER mode is engaged with

Auto Timer set to "OFF" (Z pg. 42).

● The batteries are discharged.

● The A/B CODE switch is in the

wrong position.

● The TV/CABLE/VCR switch is in the

wrong position.

SYMPTOM

1. The power won’t come on.

2. The clock works, but the VCR’s power won’t come on.

3. The remote control won’t function.

CORRECTIVE ACTION

Connect the power cord. Press TIMER to disengage.

Replace the dead batteries with new ones. Re-perform the A/B Code setting (Z pg. 49). Set the switch to the position corresponding with the unit you want to operate.

TAPE TRANSPORT

POSSIBLE CAUSE

● The cassette was inserted incorrectly.

● The Counter Memory indicator

(“M”) is lit on the front display panel.

SYMPTOM

1. The cassette gets stuck partway during loading, and is ejected.

2. The tape stops during rewind or fast forward.

CORRECTIVE ACTION

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Then insert the cassette

Press C.MEMORY to disengage the Counter Memory mode and extinguish the indicator.

SYMPTOM

1. The tape is running but the picture won’t appear.

2. Noise appears during visual search.

3. Breaks are noticeable in Hi-Fi soundtrack.

4. The playback picture is blurred or interrupted, even though TV broadcasts are clear.

5. The Hi-Fi soundtrack cannot be heard.

PLAYBACK

POSSIBLE CAUSE

● If you’re using the RF OUT connection (Z pg. 6), the channel selector on the TV is set incorrectly.

● If you’re using the AV connection (Z pg. 6), the TV receiver is set to the wrong mode.

● This is normal.

● Automatic tracking is engaged.

● The video heads may be dirty.

● The AUDIO MONITOR option at

the Function Set screen was set incorrectly.

CORRECTIVE ACTION

Set the channel selector to channel 3 or 4.

Set the TV receiver to its AV mode.

Engage and adjust tracking manually (Z pg. 25).

The heads must be cleaned. Consult your JVC dealer (Z pg. 58).

Set AUDIO MONITOR to "HI-FI" (Z pg. 26).

Page 51

CORRECTIVE ACTION

Insert a cassette. Remove the cassette and cover the hole with adhesive tape, or load a cassette on which the record safety tab is intact.

Set the VCR to the appropriate channel.

Refer to the directions and the illustration under “Edit to And From Another VCR” (Z pg. 43) or “Edit From A Camcorder” (Z pg. 44) and properly connect the units. Make sure the power to all units is on.

Set the recorder’s input mode to AUX and select "FRONT" or "REAR" at the Aux Input Screen (Z pg. 45).

POSSIBLE CAUSE

● There’s no cassette loaded.

● The loaded cassette has had its

record safety tab removed.

● The VCR has been set to its AUX

mode by mistake.

●The VCRs or the camcorder and the

VCR have been incorrectly connected.

● The power to one or more of the

units has not been turned on.

● The recorder’s input mode has been

set incorrectly.

SYMPTOM

1. Recording won’t start.

2. TV broadcasts won’t record properly.

3. Tape-to-tape editing won’t work.

RECORDING

TIMER RECORDING

CORRECTIVE ACTION

Check or re-perform the clock/timer settings to ensure correctness. Press TIMER and check to make sure that TIMER appears on the front display panel. Re-perform the set-up procedures. Make sure you have compensated for Guide Channel and VCR or cable box channel number mismatches (Z pg. 19).

Timer programming can’t be performed when timer recording is in progress. Wait until it finishes.

Load a cassette with the record safety tab intact, or with the hole covered with adhesive tape.

Remove the cassette and cover its hole with adhesive tape, or replace it with a cassette on which the safety tab is intact.

Check the programmed data and reprogram as necessary, then press TIMER again.

The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

Connect the Cable Box Controller correctly (Z pg. 15). After confirming your cable box’s output channel number, re-access the Cable Box Output screen and select the correct number (Z pg. 17). Make sure the power is on before timer recording starts.

SYMPTOM

1. Timer recording won’t work.

2. On-screen timer programming won’t work.

3. TIMER and ] on the front display panel won’t stop blinking.

4. The cassette is automatically ejected, and TIMER and ] on the front display panel won’t stop blinking.

5. TIMER blinks for 10 seconds and the timer mode is disengaged.

6. The cassette is automatically ejected, the power shuts off and TIMER and ] won’t stop blinking.

7. Cable channels are not automatically switched during timer recording.

POSSIBLE CAUSE

● The clock and/or the timer have been set incorrectly.

● The timer is not engaged.

● The VCR has not been set up properly.

● Timer recording is in progress.

● The timer is engaged but there’s no

cassette loaded.

● The loaded cassette has had its record safety tab removed.

● TIMER has been pressed when there are no programs in memory, or the timer record program information has not been programmed correctly.

● The end of tape was reached during timer recording.

● The Cable Box Controller is not properly connected to the VCR.

● The output channel selected in the Cable Box Output screen is incorrect.

● The cable box’s power is off.

CONTINUED ON NEXT PAGE.

Page 52

8. Timer recording begins as scheduled, but the channel is always incorrect.

9. We moved, and now VCR Plus+ doesn’t work properly.

10.“PROGRAM FULL” is displayed on the VCR Plus+ screen.

● Even though you don't use an external Cable Box, "CABLE BOX OUTPUT" is set to "ON".

● The receivable stations in the new area are received on different channels than those in the previous area.

● All 8 programs of the VCR’s timer memory are used.

TROUBLESHOOTING (cont.)

ATTENTION:

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the power off and unplug the power cord. Then plug it in again and switch power on. Take out the cassette. After checking the cassette, operate the unit as usual.