JVC HR-V617EK, HR-V616EK, HR-V615EK User Manual

VIDEO CASSETTE RECORDER
HR-V615EK HR-V616EK HR-V617EK
SAT
SAT
VCR
VCR
PAL
INSTRUCTIONS
HR-V615/616/617EK-Cover 3/17/04, 09:46 AM1
Black
LPT0909-001A
safety first2
Safety Precautions
The rating plate and the safety caution are on the rear of the unit.
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
IMPORTANT
Please read the various precautions on pages 2–4 of this instruction manual before installing or operating the recorder.
It should be noted that it may be unlawful to re-record pre-recorded tapes, records, or discs without the consent of the owner of copyright in the sound or video recording, broadcast or cable programme and in any literary, dramatic, musical, or artistic work embodied therein.
IMPORTANT
Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is
too short to reach a power point, then obtain a proper safety approved extension lead/adapter or consult your dealer.
In the unlikely event of the plug fuse failing be sure to replace the fuse only with an identical approved type, as originally fitted, and to replace the fuse cover. If the fuse fails again consult your nearest JVC dealer.
If nonetheless the mains plug is cut off remove the fuse and dispose of the plug immediately, to avoid a possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below: DO NOT make any connection to the Larger Terminal coded E or Green. The wires in the mains lead are coloured in accordance with the following code:
Blue to N (Neutral) or Black Brown to L (Live) or Red
If these colours do not correspond with the terminal identifications of your plug, connect as follows: Blue wire to terminal coded N (Neutral) or coloured Black. Brown wire to terminal coded L (Live) or coloured Red.
If in doubt — consult a competent electrician.
CAUTION
When you are not using the recorder for a long period of time, it is recommended that you disconnect the power cord from the mains outlet.
Dangerous voltage inside. Refer internal servicing to qualified service personnel. To prevent electric shock or fire hazard, remove the power cord from the mains outlet prior to connecting or disconnecting any signal lead or aerial.
The STANDBY/ON o button does not completely shut off mains power from the unit, but switches operating current on and off. “y ” shows electrical power standby and “ z” shows
Video tapes recorded with this video recorder in the LP (Long Play) mode cannot be played back on a single-speed video recorder.
ON.
HR-V615/616/617EK-EN/p02-07 3/8/04, 10:04 AM2
Black
safety first 3
When the equipment is installed in a cabinet or a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm or more on both sides, on top and at the rear.)
When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.
Failure to heed the following precautions may result in damage to the recorder, remote control or video cassette.
DO NOT place the recorder…
1.
… in an environment prone to extreme temperatures or humidity. … in direct sunlight. … in a dusty environment. … in an environment where strong magnetic fields are generated. … on a surface that is unstable or subject to vibration.
DO NOT block the recorder’s ventilation openings or holes.
2.
(If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.)
DO NOT place heavy objects on the recorder or remote control.
3.
4.
DO NOT place anything which might spill on top of the recorder or remote control.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)
DO NOT expose the apparatus to dripping or splashing.
5. DO NOT use this equipment in a bathroom or places with water. Also DO NOT place any con-
6.
tainers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups, etc.) on top of this unit.
DO NOT place any naked flame sources, such as lighted candles, on the apparatus.
7. AVOID violent shocks to the recorder during transport.
8.
MOISTURE CONDENSATION
Moisture in the air will condense on the recorder when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form in the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the recorder turned on for a few hours to let the moisture dry.
ATTENTION
TO MOBILE PHONE USERS:TO MOBILE PHONE USERS:
TO MOBILE PHONE USERS:
TO MOBILE PHONE USERS:TO MOBILE PHONE USERS: Using a mobile phone in the vicinity of the recorder may cause picture vibration on the TV screen or change the screen to a blue back display.
ON PLACING THE RECORDER:ON PLACING THE RECORDER:
ON PLACING THE RECORDER:
ON PLACING THE RECORDER:ON PLACING THE RECORDER: Some TVs or other appliances generate strong magnetic fields. Do not place this appliance on top of the recorder as it may cause picture disturbance.
Cassettes marked “VHS” (or “S-VHS”) can be used with this video cassette recorder. However, S-VHS recording is not possible with this model.
This model is equipped with SQPB (S-VHS QUASI PLAYBACK) that makes it possible to play back S-VHS recordings in the SP mode with regular VHS resolution.
HQ VHS is compatible with existing VHS equipment.
VIDEO Plus+ and PlusCode are registered trademarks of Gemstar Development Corporation. The
VIDEO Plus+ system is manufactured under license from Gemstar Development Corporation.
HR-V615/616/617EK-EN/p02-07 3/8/04, 10:04 AM3
Black
safety first4
Some Do’s And Don’ts On The Safe Use Of Equipment
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.
DO read the operating instructions before you attempt to use the equipment. DO ensure that all electrical connections (including the mains plug, extension leads and interconnec-
tions between pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing connections.
DO consult your dealer if you are ever in doubt about the installation, operation or safety of your
equipment.
DO be careful with glass panels or doors on equipment. DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is
damaged in any way — switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages. DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is
designed for unattended operation or has a standby mode. Switch off using the switch on the equipment and make sure that your family knows how to do this. Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the require-
ments of road safety. It is illegal to watch television whilst driving.
DON’T listen to headphones at high volume, as such use can permanently damage your hearing. DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety
always fit the manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL...
NEVER let anyone especially children push anything into holes, slots or any other opening in
the case — this could result in a fatal electrical shock;
NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than
sorry!
HR-V615/616/617EK-EN/p02-07 3/8/04, 10:04 AM4
Black
Contents
Diagrams of Equipment ................................6
Equipment Key ............................................. 7
Welcome to JVC ............................................8
Three-Step Quick Start ............................... 10
Basic Features ............................................ 13
Advanced Features ..................................... 29
Subsidiary Information .............................. 55
List of Terms .............................................. 59
HR-V615/616/617EK-EN/p02-07 3/8/04, 10:04 AM5
Black
diagrams of equipment6
1 2 3
t y
o
u
^ &
r
Q
i
q
*
8
3
9
0
!
@
$
5
#
%
)
w
(
e
p
W E R
T
Y
2
front panel
1
1
ENTREE/DECODEUR IN/DECODER
010
010
3
L-1L-2
ENTREE/SORTIE IN/OUT
2
CONTROLEUR SAT
CONTROLEUR SAT
SORTIE
SAT CONTROL
R
AUDIO
AUDIO
L
L
2
SAT
VCR
REVIEW
6
4
5
7
8
3
ENTREE ANT. IN
OUT
ANTENNE
SORTIE RF OUT
1
9
0
!
*DECODER function is not available in the UK.
rear panel
display
HR-V615/616/617EK-EN/p02-07 3/17/04, 09:51 AM6
Black
4
5
67
VCR
4 5
7
6
SAT
REVIEW
4
6 7
remote control
Diagram Key
/
equipment key 7
FRONT PANEL
1 STANDBY/ON o Button turns VCR on/off (loading a cassette also turns power on). 2 Cassette Loading Slot is where cassette is inserted; door closes. 3 PR+/- Buttons select a preset position. 4 Display Panel provides clear view of various displays and indicators. 5 Infrared Beam Receiving Window is where Remote Control should be aimed when in use. 6 < Button rewinds the tape; initiates reverse picture search. 7 > Button fast­forwards tape; initiates forward picture search. 8 T Button starts regular recording (press once), Instant Timer Recording (press twice); sets duration of ITR. 9 | Button stops tape temporarily during recording; stops tape temporarily during playback; plays back frame by frame with each additional press.
SATc Button enables/
disables the Auto Satellite Programme Recording mode.
§ Button stops tape;
10 ejects tape during Stop mode. 11 . Button plays back tape; cancels Pause, Still, Slow, Search modes.
REAR PANEL
1 Mains Power Cord supplies power to VCR. 2 SAT CONTROL Connector enables connection of the Satellite Controller for timer recording with a satellite receiver. 3 ANT. IN Connector enables connection of aerial. 4 L-2 IN/DECODER Connector enables connection of satellite receiver or second recorder.
* DECODER function is not available in the UK.
5 L-1 IN/OUT Connector enables AV connection to TV or second VCR.
6 AUDIO OUT (L/R) Connectors enable connection of audio cassette recorder, TV or second VCR for dubbing. 7 RF. OUT Connector enables connection to aerial terminal of TV receiver.
VCR DISPLAY PANEL
1 c Indicator lights when the c button has been pressed to engage Timer mode. 2 Play Indicator lights up during playback; blinks during Repeat Playback or when using Next Function Memory for playback. 3 Record Indicator lights up during recording; blinks during Instant Timer Recording. 4 Channel Display shows preset position where the station currently being received is stored.
Mode shows external input
mode selected (L-1 or L-2).
Clock Display shows
current time.
Preset Position* (or Mode) and Clock Display appear alternately when b is pressed.
* Preset Position (or Mode) is not displayed during playback.
5 REVIEW Indicator blinks after timer-recording and shows how many programmes have been timer-recorded. 6 SATc Indicator lights up during Auto Satellite Programme Recording standby mode; blinks when Auto Satellite Programme Recording is in progress. 7 VCR Indicator lights when the VCR is in the video mode. At this point, the TV automati­cally enters AV mode.
REMOTE CONTROL
1 Button ejects tape during stop mode.
STARTSTART
2
START + / Buttons
STARTSTART access Regular Program screen; input programme Start Time.
STOPSTOP
3
STOP + / Buttons input
STOPSTOP programme Stop Time. 4 PDC Button enables/ disables PDC recording.
* VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this VCR.
5 x Button cancels timer- programme.
0000 Button resets counter on the on-screen display to ‘0:00:00’. 6 Auto Tracking Button enables/disables auto tracking mode during playback.
/ Button selects tape. 7 AUDIO Button changes output sound mode. 8 PROG Button accesses Timer Programming Set screen. 9 OK Button enters selections made in on-screen menus. 10 Buttons initiate functions such as frame by frame playback and variable speed search. 11 C Button accesses Program screens/displays to check the programme that you have programmed (next programme’s information screen appears each time button is pressed). 12 Buttons initiate index function. 13 < Button rewinds the tape; inltiates reverse picture search. 14 S Button stops tape. 15 T Button starts regular recording (press . the same time)
Button shows current
16 VCR status on the TV screen if O.S.D is set to ON. 17 TV PR +/– Buttons select the connected JVC TV's channel. 18 rButton ‘reviews’ timer-recorded programme.
19 TV
input terminal. 20 STANDBY/ON o Button — same as button on VCR. 21 Number Keys are used in preset position selection and the VIDEO Plus+ Timer Programming. 22 DATE + / Buttons input date of programme for timer recording. 23 DAILY Button enables timer recording of daily serials. 24 WEEKLY Button enables timer recording of weekly serials. 25 AUX Button selects VCR’s auxiliary input mode. 26 c Button engages timer- standby mode. 27 b(Display) Button switches display between clock time and Preset Position* (or Mode).
Preset Position (or Mode) is not displayed during playback.
28 TV/VCR Button switches connected TV’s mode between TV and AV. 29 MENU Button accesses Menu screen. 30 PR Buttons are used for selection in on-screen menus.
preset position. 31 3 Button initiates a 30-second period of fast-motion playback. 32 . Button — same as button on VCR. 33 > Button fast- forwards tape; inltiates forward picture search. 34 | Button — same as button on VCR. 35 TV volume of connected JVC TV. 36 TV STANDBY/ON o
Button turns TV on/off.
Button switches TV
/
PR + / Buttons select a
+/– Buttons control
HR-V615/616/617EK-EN/p02-07 3/12/04, 10:20 AM7
Black
welcome to jvc8
VCR
SAT
REVIEW
before you start
Please read the SAFETY
FIRST on pages 2–4
it tells you about some
safety points
Refer to the diagrams on
pages 6–7 when reading
through these
instructions
Refer to the List of
Terms on page 59 if you need an explanation for
any terms in this manual
remote control
The Remote Control can
operate most of your
VCR’s functions, as well
as basic functions of JVC
TV sets. (see page 7)
Depending on the type
of JVC TV. Some or all
functions cannot be
operated using the
Remote Control.
Welcome to JVC
Thank you for choosing JVC.
We hope that you will get many hours of enjoy­ment from your new unit.
In just three easy steps you will be ready to enjoy the exceptional perfor­mance of your new VCR. More detailed instructions begin on page 10. They will explain how to use the many sophisticated features this VCR boasts.
Getting Everything Ready
check the contents Unpack the box and place the VCR on a flat, stable surface.
Check that you have the items shown below.
If the Remote Control
doesn’t work properly,
remove it’s battery,
replace the battery and
then try again.
Video Cassette Recorder
RF Cable
“AA” Batteries (x 2)
Infrared Remote
Control Unit
HR-V615/616/617EK-EN/p08-12 3/17/04, 09:57 AM8
Black
scart and rf
SCART is a
recommended option
because its use
improves the quality of
the picture.
If connecting to a stereo
TV you will need a
SCART cable.
There are several types
of SCART cables, fully-
wired and others.
If you use a SCART
cable, you must also
connect the RF cable.
welcome to jvc 9
GETTING EVERYTHING READY (continued)
connect cables Connect the cables as indicated in the diagram (below), using
the TV Aerial Cable, the
Mains Power Cord
Mains Outlet
You are now ready to start the Three-Step Quick Start which begins on the next page.
RF Cable and the 21-pin SCART Cable (not provided).
RF Cable
(provided)
21-pin SCART Cable
(not provided)
ENTREE/DECODEUR IN/DECODER
*DECODER function is not available in the UK.
010
ENTREE/SORTIE
L-1L-2
IN/OUT
CONTROLEUR SAT
SORTIE
SAT CONTROL
OUT
R
AUDIO
L
TV Aerial Cable
(not provided)
ENTREE ANT. IN
ANTENNE
SORTIE RF OUT
Back of VCR
You have two ways for initial setup of your new VCR depending upon the connection method and your TV.
If you have connected only the RF cable,
perform Auto Setup ( pg. 10).
If you have connected both the RF cable and the fully­wired 21-pin SCART cable, and if your TV does not offer T-VLink, etc.*,
perform Auto Setup ( pg. 10).
If you have connected both the RF cable and the fully­wired 21-pin SCART cable, and if your TV offer T-VLink, etc.*,
perform Preset Download ( pg. 11).
* Compatible with TVs offering T-VLink, EasyLink, Megalogic, SMARTLINK,
Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.
HR-V615/616/617EK-EN/p08-12 3/8/04, 10:06 AM9
Black
three-step quick start10
Three-Step Quick Start
For Step , be sure to perform either of the methods: Auto Setup or Preset Download.
Auto Setup
before you start
Check that the VCR is
turned off and no
cassette is inserted
Load the batterys into
the Remote Control
Refer to the Remote
Control diagram
on pages 6–7
Unless indicated
otherwise, use the
buttons on the Remote
Control
Check that the
connection is completed
Turn on the TV
START AUTO SETUP
Press the o button. If ‘Auto’ appears on the display panel, press OK button (or ).
what will happen? The display panel on the front of the VCR will show the
word ‘Auto’. Do not press any button on the VCR or the Remote Control. note If you have connected both the RF cable and the fully-wired 21-pin SCART cable, and if your TV offers T-VLink, etc., and the TV is turned on, the VCR automatically performs the Preset Download ( pg. 11) even if you select ‘Auto’ for Auto Setup function.
VCR
Auto Setup is running: don’t touch any buttons
AUTO SET
PLEASE WAIT
SAT
REVIEW
The VCR is automatically setting up the tuner channels, clock, the VIDEO Plus+ assigned Guide
Program numbers and the video channel. This only happens the first time that the VCR is turned on.
rf and scart connection If you have chosen to
connect the VCR to the TV with both the RF Cable and a 21-pin SCART Cable (not provided) and the TV set is in its AV mode (see the TV manual), you will see the following information displayed on
[MENU]: EXIT
your TV screen:
Your TV screen during Auto Setup if SCART is used
SELECT THE VIDEO CHANNEL
Auto Setup has finished, you will see the following display panel on your VCR:
When
– –:– –
HR-V615/616/617EK-EN/p08-12 3/8/04, 10:06 AM10
Black
rf cable only If you have only used the RF
Cable to connect the VCR to the TV, you will see this display. The number is the channel on the TV that the
Auto Setup has chosen to be the
VCR
video channel. In the example, we have pre­sumed that channel 52 is vacant and have set the VCR to 52:
Now tune the TV set to channel 52 (refer to TV manual if necessary); you should see two vertical white bars appear on the TV screen. If the bars do not appear or are not clear, choose another vacant channel pressing PR +/ -- on the Remote Control and try again. If you cannot obtain the vertical white bars on any channel between 22 and 69, consult your local JVC dealer.
rf and scart connection If you have chosen
to connect the VCR to the TV with both the RF Cable and a 21-pin SCART Cable (not provided),
VCR
you need to press PR -- on the Remote Control until the figure reads ‘– –’. This is because you will use the TV in AV mode to view video pictures and therefore do not need a dedicated video channel.
SAT
REVIEW
SAT
REVIEW
three step quick start 11
FINISH AUTO SETUP
Press OK button and move on to
Step 2 to check the results.
oops! If there is a power cut or you accidentally press a button during Auto
, turn the VCR off and then on again. Re-perform Auto Setup.
Setup
Preset Download
before you start
Check that the VCR is
turned off and no
cassette is inserted
Load the batterys into
the Remote Control
Refer to the Remote
Control diagram
on pages 6–7
Unless indicated
otherwise, use the
buttons on the Remote
Control
Check that the
connection is completed
Be sure to use the fully-
wired 21-pin SCART cable
Turn on the TV whose
channels have already
been stored
– –:– –
START PRESET DOWNLOAD
Press the o button. The display panel on the front of the VCR will show the word ‘Auto’. Press the
PR and PR button to select
VCR
SAT
REVIEW
‘CH – –’ and press OK button (or ).
what will happen? The VCR is automati-
cally setting up the tuner channels by down­loading from your TV, clock and the VIDEO Plus+ system assigned Guide Program num­bers. During downloading, preset position on the display panel increases from “CH
1”.
Preset Download is running:
don’t touch any buttons
VCR
SAT
REVIEW
rf and scart connection If the TV set is in its AV mode (see the TV
manual), you will see the following information displayed on your TV screen:
T-VLINK
PLEASE WAIT
[MENU]: EXIT
Your TV screen during Preset Download
SET THE VIDEO CHANNEL TO OFF
Preset Download has finished, ‘COM-
When PLETED’ appears on the TV screen. Press o to turn off the VCR. Press and hold down S on
VCR
SAT
REVIEW
the VCR until you will see the display on the right. Press PR -- on the Remote Control until the figure reads ‘– –’.
HR-V615/616/617EK-EN/p08-12 3/8/04, 10:07 AM11
Black
FINISH PRESET DOWNLOAD
Press OK button and move on to
Step 2 to check the results.
oops! If there is a power cut or you accidentally press a button during Preset
Download, turn the VCR off and then on again. Re-perform
Preset Download.
NOTES
• In areas where no TV station transmits the PDC signal, the VCR cannot setup either the clock or Guide Program numbers.
• On this VCR, the characters available for station names (ID) are A–Z, 0–9, –,
, + and (space). The names of some downloaded stations may differ from
*
those on your TV.
three-step quick start12
Check the Results
When Auto Setup or Preset Download finishes, you will see one of the three following examples on the VCR display panel:
The Preset Positions and the Clock have been set successfully
Go straight to Step 3 (20:00 used as example only).
The Preset Positions have been set successfully but the Clock has not
Perform Clock Set on page 54.
Step 3.
Go to
Neither the Preset Positions or the Clock have been set successfully
Make sure the cables are connected properly to the VCR and turn the VCR off and then on again. Try
Auto Set Up or Preset Download
again.
Finish Off
Select the Video channel or AV mode, then make sure that all necessary stations have been stored in the VCR’s memory by using the
PR and PR buttons.
If station names (ID — pg.52) have also been stored in the VCR’s memory, the station name will be displayed at the top left corner of the TV screen for about 5 seconds each time you select a different channel via the VCR.
The VCR is now set up. You can now use it to play and record.
IMPORTANT
re-running setup Auto Setup or Preset Download may not behave as
described if it has already been run on the VCR. This is because some of the information gathered on the first Auto Setup or Preset Download is retained in memory and that part of the process may be skipped by the VCR.
bad reception In certain reception conditions, station names may not be
• stored correctly, and
Guide Program Numbers may not be set properly. If this
happens, when you timer-record a TV programme using the VIDEO Plus+ system, the VCR will record a TV programme of a different station. When programming the timer using the VIDEO Plus+ system, be sure to check that the preset position corresponding to the broadcasting station you wish to record has been selected ( pg.21,
duplicate stations You may be able to receive the same station from two
VIDEO Plus+ Timer Programming).
different transmitters in which case Auto Setup will detect and store both. It is normal for one transmitter to give you a better quality picture than the other; to delete those stations which have a poor picture
manual station setting If any of the above problems occur, refer to
• pages50–51 to input station names ( change station preset positions (
rf connections In certain reception conditions, the Video Channel may not
Change Station Name). You can also
Change Station Preset Position).
Delete A Channel on page50.
be set correctly and interference may appear in the TV picture while the VCR’s power is on. Set your Video Channel manually. ( pg.47,
Video Channel Set)
HR-V615/616/617EK-EN/p08-12 3/8/04, 10:07 AM12
Black
IF YOU HAVE ANY DIFFICULTY WITH THE ABOVE PROCEDURES CALL THE JVC CUSTOMER SERVICE HOT LINE ON 0870 330 5000
Basic Features
Playback..................................................... 14
Playback Features ...................................... 16
Recording ................................................... 18
VIDEO Plus+® Timer Programming ............ 21
Express Timer Programming ...................... 24
HR-V615/616/617EK-EN/p13-20 3/8/04, 10:08 AM13
Black
basic features14
Playback
Playback is the most basic operation possible with your VCR. Audio-visual information recorded on a cassette will be played back on your TV screen just like a broadcast programme.
Load a Video Cassette
before you start
Turn the TV on
Tune the TV to your
Video Channel or to its
AV mode
ntsc tapes
If an NTSC tape is
played, ‘NTSCaPAL’
appears on screen for
about 5 seconds
Some TVs will shrink
the picture and place
black bars at the top and
bottom of the screen.
This is not a malfunction
but you may lose some
on-screen information
The picture may roll up
or down. Correct this by
adjusting the vertical
hold on the TV set
Make sure that the window side of the cassette is facing up and the spine label is facing away from the VCR. Insert the cassette as shown in the diagram below; don’t use too much force. If the VCR was turned off before you inserted the cassette, the power will come on automatically.
The counter on the TV screen will reset to read
0:00:00’. If the record safety tab on the video
SAT
VCR
REVIEW
‘ cassette has been removed, playback begins automatically.
Play
If the cassette that you inserted does not start playing automatically, press the . button on the VCR or the Remote Control. ‘bESt’ appears blinking in the display panel during automatic tracking ( pg.31s).
Stop & Eject
stop Press the § button on the VCR or the S button on the Remote
Control once to stop playback.
The counter and tape
remaining times will be
incorrect
The picture will be
distorted during search,
still or frame-by-frame
playback
HR-V615/616/617EK-EN/p13-20 3/17/04, 10:01 AM14
Black
eject Press the § button on the VCR a second time or press on the
remote control to eject the cassette from the VCR. The cassette will take about 6 seconds to appear once the
NOTE: You can also eject the cassette while the VCR is turned off.
§ button has been pressed.
basic features 15
Rewind and Fast Forward
During Stop Mode:
rewind Press the < button on the VCR or the Remote Control.
fast forward Press the > button on the VCR or the Remote Control.
SQPB
This VCR is equipped with SQPB (S-VHS QUASI PLAYBACK) that lets you watch tapes recorded in the S-VHS format and the SP mode, with regular VHS resolution.
NOTES:
• SQPB does not deliver Super VHS resolution.
• S-VHS recording is not possible with this VCR.
• When you play back a tape recorded in S-VHS format and the SP mode, noise may appear in the still, slow motion, or frame-by-frame playback mode.
• Depending on the tape, noise may appear during normal playback.
Video Heads Cleaning
The heads get dirty in the following cases:
• In an environment prone to extreme temperature or humidity.
• In a dusty environment.
• Flaw, dirt or mold on video tapes.
• Continuous usage for a long time.
Use a dry cleaning cassette — JVC TCL-2 — in the following cases:
• Rough, poor picture appears while a tape is played back.
• The picture is unclear or no picture appears.
• ‘USE CLEANING CASSETTE’ appears on the screen (only with ‘O.S.D.’ set to ‘ON’ ( pg.43)).
HR-V615/616/617EK-EN/p13-20 3/8/04, 10:08 AM15
Black
basic features16
Playback Features
Pause During Playback
Press the | button on the VCR or the Remote Control.
• If the paused picture on the TV screen jumps vertically, press the PR or PR button until the picture is steady.
• Press . to resume playback.
Single Frame Movement
You can move backward or forward from the still picture in one of two ways:
method one Press the | button on the VCR or the Remote Control. Each time
the | button is pressed, the frame will move forward one frame.
method two Press or on the Remote Control. Each time one of these
buttons is pressed, the frame will advance or move back one frame.
• Press . to resume playback.
HR-V615/616/617EK-EN/p13-20 3/8/04, 10:08 AM16
Black
basic features 17
Slow Motion
This VCR will play your cassette forwards or backwards in slow motion. You can make it do this in one of two ways:
method one During still picture, press and hold | on the VCR or the Remote
Control for 2 seconds, then release. Press and release | again to return to still picture.
method two During still picture, press and hold the or button on the Remote Control. The picture will return to still when you release the button.
• If the slow motion picture on the TV screen jumps vertically, press he PR or PR button until the picture is steady.
• Press . to resume playback.
Variable Speed Search
During playback, press the or button on the Remote Control. The more times that you press either button, the faster the rate of search. To decrease the speed of search, press the button for the opposite direction.
• Press . to resume playback.
Picture Search
You can perform picture search in either direction. During playback or still picture, press the > on the Remote Control for forward picture search, or the < button for reverse picture search. Each time you press <or >, the search speed changes between low-speed and high-speed.
• Press . to resume playback.
NOTES:
In the search, still, slow motion or frame-by-frame playback mode
• The picture will be distorted
• The noise bars will appear
• There will be a loss of colour with an LP-recorded tape.
HR-V615/616/617EK-EN/p13-20 3/8/04, 10:08 AM17
Black
basic features18
Recording
TV signals being received by the recorder’s built in tuner can be recorded onto a video tape. You can ‘capture’ a TV programme using your VCR.
Choose a Programme
before you start
Turn the TV on
Tune the TV to your
Video Channel or to its
AV mode
Choose a blank
cassette which has the
record safety tab still in
place
Record
Safety Tab
Load the cassette into
the VCR (see page 14)
Press PR or PR or the number keys on the Remote Control or PR +/– on the VCR to select the channel that you wish to record.
Set the Tape Speed
Press /. The current setting for the tape speed appears on the on-screen display or the VCR display panel for about 5 seconds. Press /again to change the setting while tape speed is displayed. You can choose Standard Play (SP) or Long Play (LP). The picture quality on LP recordings will not be as high as on SP recordings, but the tape will last longer.
Start Recording
There are two ways to start recording:
method one Press and hold T and then press . on the Remote Control.
method two Press T on the VCR.
HR-V615/616/617EK-EN/p13-20 3/8/04, 10:08 AM18
Black
When “DIRECT REC” is set to “ON” (pg. 35), if you press any button just after pressing Ton the VCR (or T and . on the Remote Control), the recorder may not function properly.
Pause and Resume During Recording
On either the VCR or the Remote Control, press | to temporarily stop recording and press . to resume. You cannot change the preset position on the VCR while it is recording but you can while it is paused (see of this page).
Choose a Programme at the top
basic features 19
Notes on Recording
When using both the RF and SCART connections, you can switch between TV and VCR by pressing the
If the tape reaches its end during recording, the recording stops and “U” and “,” on the display panel blink. Press S/0 on the VCR or on the remote control to eject the tape or press < to rewind the tape.
TV/VCR button on the Remote Control.
Display Tape Remaining Time
Press the bbutton so that the tape remaining time is shown on the TV screen with ‘REMAIN’ indication. The on-screen information will disappear after about 5 seconds.
non-standard tapes Sometimes, a tape will not conform to the standards
accepted by this VCR. In such cases the tape remaining time may not appear immediately, be incorrect or simply show as ‘– – : – –’.
Change Display Information
By pressing the bbutton repeatedly, you can change the display on the VCR between the clock time and the preset position. The preset position cannot be shown during playback.
Resetting the Counter
Press the bbutton so that the counter display appears on the TV screen. While the display is shown, press the ‘0:00:00’ before starting playback or recording.
0000 button. You can reset the counter to
Record a Programme While Watching Another
Once you have started recording all you need to do is use the controls on your TV set to tune to a different programme. The programme set using the Remote Control is the one which will be recorded.
PR + / on
HR-V615/616/617EK-EN/p13-20 3/12/04, 10:41 AM19
Black
basic features20
Recording Resume Function
If there is a power cut during recording (or Instant Timer Recording or timer recording), the recording will resume automatically when power is restored to the VCR unless the VCR’s memory backup has expired.
Instant Timer Recording
This method allows you to quickly set the VCR to record in 30 minute increments.
start recording Press T on the VCR once. If left in this state, the VCR will
keep recording until the tape runs out.
engage instant timer recording Press T again and the display panel will
show a flashing Record indicator (U) and ‘0:30’. This means that the VCR will record for 30 minutes on the programme already selected and then stop automatically.
increase time Each time T is pressed, the time limit is increased by
30minutes to a maximum of 6 hours.
This function only works with the T button on the VCR, not the Remote Control.
If the tape reaches its end during recording, the recording stops and “U” and “ ,” on the display panel blink. Press S/0 on the VCR or on the remote control to eject the tape or press < to rewind the tape.
HR-V615/616/617EK-EN/p13-20 3/12/04, 10:41 AM20
Black
basic features 21
®
VIDEO Plus + Timer Programming
before you start
Make sure that the
VCR’s clock is set
correctly
Insert a cassette with
the safety tab in place
Turn on the TV and
select the Video channel
or the AV Mode
The VIDEO Plus+ system uses the code numbers – called PlusCode numbers – printed after each programme in your TV listings guide. These are a kind of shorthand for video recorders and using them automatically sets your VCR to record the correct programme, channel and time.
The VIDEO Plus+ Deluxe system enables a VCR to automatically control satellite channels through a satellite receiver using an optional Satellite Controller ( pg. 36).
Get to the VIDEO Plus + Screen
Press PROG. Press 1 to place the pointer next to
PLUSCODE NO.
[0–9] a VIDEO PLUS+ PROG [PROG] : EXIT
“VIDEO PLUS+”, then press OK. The PLUSCODE NO. screen appears.
HR-V615/616/617EK-EN/p21-28 3/12/04, 10:52 AM21
Black
Enter the PlusCode Number
Press the number keys on the Remote Control to
PLUSCODE NO.
5 6 7 8 1 2 3 4
[0–9] a k [x]: DELETE [PROG]: EXIT
enter the PlusCode number of the programme you wish to record. If you make a mistake, press x to delete the incorrect number and then enter the correct one.
basic features22
Check the Results
Press OK button. The VIDEO Plus+ Program
START
21:00
SP
DATE
25.12
-P2-
56781234
-P1-
VPS/PDC OFF
STOP 22:00
TV PROG
1
BBC1
PLUSCODE NO.
k: OK [0]: SAT
set channel position number Make sure the channel position you wish to
record is displayed. If “ correctly. Press
PR + or PR – button to input the channel position number on
TV PROG” displays “– –”, set the Channel Position number
which your recorder receivers the station. Then press OK button (or ).
set tape speed You can change the tape speed between Standard Play (SP)
and Long Play (LP) by pressing /.
set pdc mode Press PDC (number key 7) to change between ON and OFF.
Programme Delivery Control ( recording still works in the event of a change in time of broadcast. If you set to ON, your VCR will be turned on not by its own timer but by a signal transmitted by the broadcaster. This means that if an advertised programme is delayed, your VCR will still record it properly.
screen appears.
Make sure that the preset number displayed is the one that you want. If it is incorrect, the wrong programme will be recorded.
errors If the PlusCode number you entered is
invalid,
ERROR appears on the TV screen.
PDC) is a service designed to ensure that timer
PDC
change stop time Press STOP + / (number key 2 and 5). You can
compensate for anticipated changes in schedule using this method.
serial recording To set the VCR to record the same programme on a daily
(Monday-Friday) or weekly basis, press
DAILY (number key 8) or WEEKLY
(number key 9) to turn the function on. Pressing the same key again turns the function off. You will see your selection appear on the TV screen.
capacity You can set this VCR to timer record up to eight programmes. If you
try to enter a ninth,
PROGRAM FULL appears on the screen.
satellite receiver users To timer-record a satellite broadcast using the VIDEO Plus+ system:
• Perform ‘Satellite Receiver Control Settings’ ( pg. 36).
• You cannot set
PDC to ON.
• You cannot timer-record the satellite broadcast received on the channel position ‘0’ by the satellite receiver.
• Leave the satellite receiver’s power on.
Return to Normal Screen
Press PROG or OK button. PROGRAM COMPLETED appears on the TV screen for about 5seconds, then the normal TV screen appears. If the timer programme is overlapped with another one that was already set, appears on the TV screen. ( pg. 27)
PROGRAM OVERLAPPED
HR-V615/616/617EK-EN/p21-28 3/12/04, 10:52 AM22
Black
basic features 23
Engage Timer Mode
You must now put the VCR into Timer Mode by pressing c otherwise no recording will take place. c will appear on the display panel. Make sure that the VCR turns off automatically. To disengage the Timer Mode, press c again.
If a video tape with the safety tab removed is loaded, c, Play indicator (,) and Record indicator (U) will flash. Insert another tape with the safety tab in place to record!
If no video tape is loaded, c indicator will flash. Insert a tape to record!
If the tape reaches its end during timer recording, the recording stops and “c”,U” and “,” on the display panel blink. Press c to disengage timer, then press S/0 on the VCR or on the Remote Control to eject the tape or press othen press < to rewind the tape.
HR-V615/616/617EK-EN/p21-28 3/12/04, 10:52 AM23
Black
basic features24
before you start
Express Timer Programming
If you do not know the PlusCode number for the programme that you wish to record, follow the instructions below to manually set your VCR to record.
Make sure that the
VCR’s clock is set
correctly
Insert a cassette with
the safety tab in place
Turn on the TV and
select the Video channel
or the AV Mode
Get to the Timer Programming Set Screen
Press PROG. You will see the following TV screen
VIDEO PLUS+
F
EXPRESS PROGRAMING
[1] a k [PROG]: EXIT
information.
Get to the Programme Screen
Press 1 to place the pointer (highlighted bar) next to “EXPRESS PROGRAMING”, then press OK.
Enter Programme Details
– P1 –
START STOP
a
21:00
SP VPS/PDC OFF DATE TV PROG
- -.- -
[+/–] a k [PROG]: EXIT [0]: SAT
- -:- -
- -
set start time Use the START + / buttons
(number keys
set stop time Use the STOP + / buttons
(number keys
set date Use the DATE + / buttons (number
3 and/or 6) to adjust the date (current date
keys
1 and/or 4) to enter the start time.
2 and/or 5) to enter the stop time.
will automatically appear).
HR-V615/616/617EK-EN/p21-28 3/12/04, 10:52 AM24
Black
set programme Use the PR + / buttons to enter
the programme required.
set tape speed You can change the tape speed between Standard Play (SP)
and Long Play (LP) by pressing /.
basic features 25
set pdc mode Press PDC (number key 7) to change between ON and OFF.
Programme Delivery Control ( recording still works in the event of a change in time of broadcast. If you set to ON, your VCR will be turned on not by its own timer but by a signal transmitted by the broadcaster. This means that if an advertised programme is delayed, your VCR will still record it properly.
satellite receiver users To timer-record a satellite broadcast using Express Timer Programming:
• Perform ‘Satellite Receiver Control Settings’ ( pg. 36).
• Press
• You cannot set
• You cannot timer-record the satellite broadcast received on the channel
• Leave the satellite receiver’s power on.
AUX (number key 0) to change TV PROG to SAT. Then press PR + / to
enter the preset position for the satellite receiver.
PDC to ON.
position ‘0’ by the satellite receiver.
PDC) is a service designed to ensure that timer
PDC
For memory capacity and Serial Recording, see on page22.
VIDEO Plus+ Timer Programming
Return to Normal Screen
Press PROG or OK button. PROGRAM COMPLETED appears on the TV screen for about 5 seconds, then the normal TV screen appears. If the timer programme is overlapped with another one that was already set, appears on the TV screen.( pg. 27)
PROGRAM OVERLAPPED
Engage Timer Mode
You must now put the VCR into Timer Mode by pressing c otherwise no recording will take place. c will appear on the display panel. To disengage the Timer Mode, press c again.
If a video tape with the safety tab removed is loaded, c, Play indicator (,) and Record indicator (U) will flash. Insert another tape with the safety tab in place to record!
HR-V615/616/617EK-EN/p21-28 3/12/04, 10:52 AM25
Black
If no video tape is loaded, c indicator will flash. Insert a tape to record!
If the tape reaches its end during timer recording, the recording stops and “c”,U” and “,” on the display panel blink. Press c to disengage timer, then press S/0 on the VCR or on the Remote Control to eject the tape or press othen press < to rewind the tape.
basic features26
Check, Cancel & Change Programmes
Press c, then press o to disengage the timer mode.
review the programmes Press C. The TV
screen will display a list of the programmes set for timer recording (screen A).
Pressing C again will cycle through each of the entries in the VCR’s memory (screen B).
cancel a programme Press x to cancel a
programme.
change a programme Use START + /
(number keys 1 and 4), STOP + / (number keys 2 and 5), DATE + / (number keys 3 and 6), PR + / , /, DAILY (number key 8), WEEKLY (number
9) and PDC (number key 7) buttons as
key necessary.
return to normal screen Press C as many
times as necessary.
return to timer mode If there are still
programmes to be recorded, press c.
1 2 3 4 5 6 7 8
[ ]: NEXT
10:00 11:30
10:45 13:00
STOP
START
10:00
8:00
Screen A
– P1 –
START STOP
a
8:00
SP VPS/PDC OFF DATE TV PROG
24.12
]: NEXT
[
Screen B
CH
10:00
ITV
DATE
3
24.12
2
25.12
1
25.12
3
HR-V615/616/617EK-EN/p21-28 3/8/04, 10:17 AM26
Black
basic features 27
When Programmes Overlap Each Other
If PROGRAM OVERLAPPED appears, you have another programme overlapping the programme you have just made.
confirm overlapping programmes The Program Check screen appears and conflicting programmes will start blinking.
Example: Programme 1 (you have just made) and Programme 4 overlap each other.
select programme to modify Press
buttons, then press OK button (or ).
PR
PR + or
1 2 3
4
5 6 7 8
[1] a k [PROG]: EXIT
START
8:00 10:00 11:30
9:00
STOP 10:00 10:45 13:00
10:00
CH
DATE
3
24.12
2
25.12
1
25.12
92
DAILY
You can only select one of the overlapping programmes.
note If you do not mind this overlap, press PROG
to finish the timer programme setting. The program starting earlier or program with the lower program will be recorded.
cancel a programme Press x to cancel a
programme when the Program screen you do not
[x]: DELETE [+/–] a k [PROG]: EXIT
– P1 –
START STOP
8:00
SP VPS/PDC OFF DATE TV PROG
24.12 3
10:00
ITV
want is shown.
change a programme Use the START + /
(number keys 1 and 4), STOP+ / (number keys 2 and 5), DATE + / (number
3 and 6), PR + / , /and PDC buttons as necessary, then press OK
keys button.
PROGRAM COMPLETED appears on the screen for about 5seconds, then normal
screen appears.
note If the overlap is not yet solved or another overlap occurs with the timer
programme setting made last after making correction on a programme, the conflicting programmes will be shown on the Program Check screen again. Repeat the above steps again until the overlap is solved.
HR-V615/616/617EK-EN/p21-28 3/12/04, 10:52 AM27
Black
basic features28
HR-V615/616/617EK-EN/p21-28 3/8/04, 10:17 AM28
Black
Advanced Features
Picture Quality ........................................... 30
The B.E.S.T. Picture System ...................... 31
Sound Modes ............................................ 32
Finding Specific Scenes ............................ 33
T-VLink Functions..................................... 34
Satellite Receiver Control Settings ........... 36
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM29
Black
Auto Satellite Programme Recording ........ 39
Editing ....................................................... 41
Other Functions ......................................... 43
Connection to a Stereo System .................. 46
Video Channel Set ..................................... 47
Tuner Set ................................................... 48
Clock Set ................................................... 54
advanced features30
Picture Quality
Manual Tracking
Your VCR is equipped with automatic tracking control. This will be adequate for most tapes and will automatically adjust the tracking to suit the particular tape in use but if you insert an old or worn tape, it may be necessary to manually adjust the track­ing in order to get the best picture. If automatic tracking fails, you will notice noise bars appear­ing across the picture; you can correct this by manually overriding the tracking using the follow­ing steps.
override automatic tracking During playback, press / on the Remote Control to
engage manual tracking.
adjust tracking manually Use the PR + or – buttons to adjust the tracking manually.
NOTES:
• Press / again to re-engage automatic tracking.
• When a new tape is inserted, the VCR returns to automatic tracking.
Picture Control
This feature allows you to select the most appropriate picture quality according to the type of tape or use of this VCR. The default setting is
get to the mode set screen Press MENU button. Move the highlight bar to MODE SET
using the PR and PR buttons and press OK button (or ).
select picture control mode Move the highlight bar to PICTURE CONTROL using the PR
and PR buttons. Press OK button (or ) to select the desired mode:
AUTO (NORM) Provides optimised picture benefits of
• B.E.S.T. Picture System. When
CONTROL EDIT Minimizes picture degradation during editing (record-
switches automatically from AUTO to NORM.
B.E.S.T. is OFF, PICTURE
ing or playback).
SOFT Reduces image coarseness when viewing overplayed
• tapes containing lots of noise.
AUTO.
MODE SET
B.E.S.T. ON
F
PICTURE CONTROL AUTO
AUTO TIMER OFF O.S. D. ON DIRECT REC ON AUTO SP a LP TIMER OFF POWER SAVE OFF AUTO POWER OFF OFF
[1] a k [MENU]: EXIT
return to normal screen Press MENU button.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM30
Black
The B.E.S.T. PictureSystem
advanced features 31
about b.e.s.t.
Works in SP and LP
modes
Does not work with
Auto Satellite Prog
Recording
Works before Timer
Recording
B.E.S.T. data is lost
when tape is ejected
Pressing the T button on
VCR does not start Instant
Timer Recording while
B.E.S.T. is turned ON
Recording and Playback Using B.E.S.T.
The Biconditional Equalised Signal Tracking (B.E.S.T.) System checks the condition of the tape in use and compensates during recording and playback to give the best picture quality possible. The default setting is ON.
Turning B.E.S.T. ON or OFF
get to the mode set screen Press MENU
button . Move the highlight bar to
MODE SET
using the PR and PR buttons and press OK button (or ).
select b.e.s.t. mode Move the highlight bar to
B.E.S.T. using the PR and PR buttons and
press OK button (or ) to set
OFF.
B.E.S.T. ON or
return to normal screen Press MENU button.
F
[1] a k [MENU]: EXIT
MODE SET
B.E.S.T. ON
PICTURE CONTROL AUTO AUTO TIMER OFF O.S. D. ON DIRECT REC ON AUTO SP a LP TIMER OFF POWER SAVE ON AUTO POWER OFF OFF
recording Press and hold T and press . on the Remote Control (or press T on the VCR). The
VCR spends about 7 seconds assessing the condition of the tape and then begins recording.
During B.E.S.T.
playback Press .. The VCR adjusts the playback picture quality
based on the condition of the tape in use. B.E.S.T. is active during Auto Tracking.
Avoiding B.E.S.T. Time Delay
Since B.E.S.T. introduces a 7 second delay before recording starts, you may wish to compensate by first pressing | and T together (this puts the VCR into the VCR performs the B.E.S.T. tape assessment) and then pressing . when you wish to start recording.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM31
Black
SAT
VCR
REVIEW
bESt appears on the VCR’s display panel.
a pause of 7 seconds a
B.E.S.T. complete
SAT
VCR
REVIEW
SAT
VCR
REVIEW
RECORD PAUSE mode during which time
advanced features32
Sound Modes
NICAM Stereo and Bilingual Broadcasts
before you start
Set On Screen Display
(O.S.D.) to ON
( pg. 43)
This VCR is equipped with a digital stereo sound decoder (NICAM) which makes the reception of stereo and bilingual broadcasts possible. When the VCR is tuned to a different preset, the type of broadcast will be displayed on the TV screen for a few seconds.
select stereo Press AUDIO until HIFI L l L R appears on the TV screen.
select bilingual Press AUDIO until HIFI L l or HIFI L R appears on the TV
screen (as required).
select standard To listen to standard monaural audio during a NICAM
broadcast, press
AUDIO until NORM appears on the TV screen.
Soundtrack Selection
This VCR is capable of recording three soundtracks and will play back the one that you select with the
track use
HI FI
Hi-Fi stereo pre-recorded tapes
L l L R
HI FI
Main audio of bilingual tapes
L l
HI FI
Sub-audio of bilingual tapes
L R
AUDIO button.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM32
Black
NORM
Audio-dubbed tapes
HI FI
Audio-dubbed tapes
NORM
Notes
normal selection hi fi l l L r should normally be selected. In this mode,
Hi-Fi stereo tapes are played back in stereo and the normal audio track is played back automatically for tapes which only have normal audio.
recording If the NICAM stereo signal is poor or unavailable, the VCR will
automatically record standard monoaural audio onto both the Hi-Fi and normal audio tracks. This will eliminate possible audio interference.
advanced features 33
Finding Specific Scenes
Skip Search
During playback, press 3 up to 4 times. Each press of the 3 button will cause the VCR to go into fast-motion playback for a period of 30 seconds. Normal playback resumes automatically.
• To return to normal playback during a Skip Search, press ..
Index Search
Each time you record a programme, this VCR puts an index marker at the point that you started recording. The VCR can fast wind to any one of nine index markers in either direction from the point that you stop the tape.
NOTE:
Before starting, make sure the VCR is in the Stop mode.
finding first index marker Press
VCR begins searching through the tape in the corresponding direction for the first index marker from its current position.
finding subsequent index markers Press
[
The TV screen will display corresponding direction for the fifth index marker from its current position.
5 or ]5 and the VCR begins searching through the tape in the
[
or ] once. The TV screen will display
[
or ] the required number of times (e.g. five).
[
1 or ]1 and the
Instant Review
After ensuring that the VCR is turned off and that the timer mode is disengaged, press r.
Pressing the rbutton causes the VCR to turn on, rewind to the beginning of the last timer-recorded programme and begin playback. The display panel tells you how many timer-recorded programmes are on the tape. If you have three, the REVIEW indicator and ‘ programmes, press rthree times. You can move back up to nine programmes from your current position.
NOTE:
Instant Review will also operate if the VCR is turned on.
3’ blink on the display panel. To watch the first of these three
VCR
SAT
REVIEW
timer mode Instant Review will not work while the VCR is in Timer mode.
auto satellite programme recording If Auto Satellite Programme Recording has been used
to record the programmes, the number of recorded programmes will not be displayed on the display panel.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM33
Black
advanced features34
T-V Link Functions
When you connect the VCR and your TV via both the RF cable and the fully­wired 21-pin SCART cable ( pg. 9), the following functions are available. You can use these functions only with a TV offering T-V Link, etc.* For details, refer to the instruction manual for your TV. * Compatible with TVs offering T-V Link, EasyLink, Megalogic, SMARTLINK, Q-Link, DATA LOGIC or NexTView Link via fully-wired 21-pin SCART cable. The degree of compatibility and available functions may differ by system.
Next View Link
You can download the EPG (Electronic Programme Guide) information from your TV for timer-programming on the VCR. For details, refer to the instruction manual for your TV.
TV Auto Power On
You can turn on the TV and set it to video mode automatically whenever you play a tape. For details, refer to the instruction manual for your TV.
VCR Auto Standby
You can use your TV’s Remote Control to turn off the VCR. For details, refer to the instruction manual for your TV.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM34
Black
advanced features 35
Direct Rec
You can start recording the programme that you are watching on your TV with simple operation. Press and hold T and press . on the Remote Control, or press T on the VCR. Follow the procedure below to use this function.
get to the mode set screen Press MENU button. Move the highlight bar to
MODE SET using the PR and PR buttons and press OK button (or ).
select direct rec mode Move the highlight
DIRECT REC using the PR and PR
bar to buttons. Press OK button (or ) to select or OFF.
return to normal screen Press MENU
button.
ON
F
[1] a k [MENU]: EXIT
NOTES
• When DIRECT REC is set to ON, if you press
any button just after pressing Ton the VCR (or Tand . on the Remote Control), the recorder may not function properly.
DIRECT REC is set to OFF, the T button functions as described in Recording
• If
F
( pg. 18).
• During the Direct Rec, ‘– –’ appears on the display panel.
• Direct Rec is not possible with a scrambled broadcast. To record a scrambled broadcast, set
Recording on page 18.
DIRECT REC to OFF and follow the procedure described in
MODE SET B.E.S.T. ON PICTURE CONTROL AUTO AUTO TIMER OFF O.S. D. ON
DIRECT REC ON
AUTO SP a LP TIMER OFF POWER SAVE OFF AUTO POWER OFF OFF
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM35
Black
advanced features36
Satellite Receiver Control Settings
The following procedure is required if you receive satellite channels through a satellite receiver. Around 20 seconds before the VIDEO Plus+ timer record­ing or Manual timer recording starts, the VCR sets its input mode to L-2 and automatically switches the satellite receiver’s channels using an optional Satellite Controller.
Installing Satellite Controller
situate satellite controller Place the Satellite Controller so that the path between its transmitter and the satellite receiver’s remote sensor is unobstructed.
attach satellite controller Fix securely using the adhesive strip at­tached on the back of the Satellite Controller.
connect up Be sure to connect the recorder’s
L-2 IN/DECODER connector to
the satellite receiver’s 21-pin SCART connector.
note When connecting your satellite receiver, refer to its instruction manual.
connect satellite controller to vcr Connect the Satellite Controller to
SAT CONTROL connector on the rear
the panel.
Your VCR
Transmitter
Satellite Receiver
DECODER VCR TV
Satellite Receiver
Satellite Controller
(not provided)
(suggested locations)
Satellite Controller
(not provided)
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:18 AM36
Black
Your VCR
ENTREE/DECODEUR
L-1L-2
IN/DECODER
010
*DECODER function is not available in the UK.
ENTREE/SORTIE IN/OUT
CONTROLEUR SAT
SAT CONTROL
AUDIO
ENTREE ANT. IN
SORTIE
OUT
ANTENNE
R
SORTIE RF OUT
L
advanced features 37
Setting satellite receiver’s brand
After installation, set the satellite receiver’s brand correctly and perform test; otherwise, the Satellite Controller cannot work correctly.
turn on satellite receiver Turn on the satellite receiver’s power.
get to the mode set screen Press MENU button. Move the highlight bar to
INITIAL SET using the PR and PR buttons and press OK button (or ).
get to the sat control set screen Move the highlight bar to SAT CONTROL
SET
using the PR and PR buttons. Press OK button (or ).
enter satellite receiver’s brand Press the
appropriate number keys to enter the brand code from the list below, then press OK button.
SAT CONTROL SET
BRAND : – – –
• If the brand code you entered is invalid, the code field is reset. Enter the correct brand code again.
• If the VCR is in playback or recording mode, you cannot set the brand code.
SATELLITE RECEIVER BRAND CODE
JVC 73, 66 AMSTRAD 60, 61, 62, 63, 92 ASTON 97 CANAL SATELLITE 81 CANAL + 81 D-BOX 85 ECHOSTAR (VIA DIGITAL) 82 FINLUX 68 FORCE 89 GALAXIS 88 GRUNDIG 64, 65, 102 HIRSCHMANN 64, 78, 99 HUMAX 88 ITT NOKIA 68 JERROLD 75 KATHREIN 70, 71, 96 LUXOR 68 MASCOM 93
SATELLITE RECEIVER BRAND CODE
MASPRO 70 NOKIA 87, 94 PAC E PANASONIC 74, 92 PHILIPS 66, 84, 101 RADIX 78 RFT 69 SABA 97 SAGEM 83, 90 SALORA 68 SAMSUNG 83 SIEMENS 64 SKYMASTER 69, 98 TECHNISAT 66, 100 THOMSON 97 TPS 83 TRIAX 91 WISI 64
F
[0–9] a k [MENU]: EXIT
65,67,74,86,92,97
HR-V615/616/617EK-EN/p29-42 3/12/04, 10:54 AM37
Black
select satellite receiver’s preset posi­tion for testing Press the appropriate
.
number keys to enter one of the channel positions on the satellite receiver, then press
.
• You can select the channel position between 1 to 999.
• After pressing
, the VCR enters the Test
mode.
SAT CONTROL SET
SAT PROG : – – –
[0–9] a k : TEST [MENU]: EXIT
advanced features38
.
Check Result of Test
If the satellite receiver’s channel number has been changed to the same channel as you set ...
Press the PR and PR buttons to move the highlight bar to
CHANGED TO ..., then press
OK button (or ) to finish the Sat Control Set mode.
SAT CONTROL SET
SAT PROG : 111
F
CHANGED TO 111
F
NOT CHANGED
[1] a k
[1] a k [MENU]: EXIT
[MENU]: EXIT
If the satellite receiver’s channel number has not been changed correctly ...
Press the PR and PR buttons to move the highlight bar to
NOT CHANGED, then press
OK button (or ). Then perform the procedure again from entering the satellite receiver’s brand code.
Notes
• The Satellite Controller may not work with all types of satellite receiver.
• For some satellite receivers, you need to set its channel input mode to 2-digit.
• If your satellite receiver has more than two channel modes, be sure to set to
All Channel Mode. For details, refer to the instruction manual of the satellite
receiver.
• When selecting the satellite receiver’s preset position for testing, signals from the Remote Control may interfere with signals transmitted from the Satellite Controller. In this case, move the Remote Control as close to the recorder’s infrared beam receiving window as possible.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:19 AM38
Black
advanced features 39
Auto Satellite Programme Recording
Auto Record from Satellite Receiver
This facility allows a programme timer-recorded using the satellite receiver to be recorded on the VCR.
connect up Connect your satellite receiver, TV and VCR (see diagram below).
21-pin AV Input
Outdoor Unit
Satellite Cable
TV Aerial
Connectors (SCART)
Back of TV
TV Aerial Cable
Aerial Connector
Satellite Receiver
DECODER VCR TV
Mains Outlet
ENTREE/DECODEUR IN/DECODER
010
010
ENTREE/SORTIE
L-1L-2
IN/OUT
ANT. IN
RF OUT
CONTROLEUR SAT
SORTIE
SAT CONTROL
R
AUDIO
L
EXT.2 EXT.1
ENTREE
ANT. IN
OUT
ANTENNE
SORTIE RF OUT
Back of VCR
*DECODER function is not available in the UK.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:19 AM39
Black
advanced features40
programme satellite receiver Enter the details of the programme into your satellite
receiver (see receiver manual) and put a tape in the VCR.
set tape speed Press / on the Remote Control to set the tape speed to either SP or LP.
engage vcr in auto mode Press and hold SATc (|)on the VCR for about 2 seconds. The
SATc indicator on the VCR display panel lights up and the VCR turns off automatically. Any
signal detected at the
L-2 IN/DECODER connecter will automatically start the VCR recording;
when the signal stops, so will the VCR.
Notes
connectors Auto Satellite Prog Recording is only possible using the L-2 IN/DECODER connec-
tor.
timer mode You cannot put the VCR into TIMER MODE when using Auto Satellite Prog
Recording Mode.
r The number of programmes recorded will not be displayed on the VCR display panel when the r button is pressed.
timer recording Auto Satellite Prog Recording is not possible if your satellite receiver does
not have a timer.
indicator The SATc indicator light flashes when Auto Satellite Prog Recording is in progress.
disengage To disengage the VCR during Auto Satellite Prog Recording, press the o button.
The VCR will stop recording and turns off.
tape speed When recording two or more programmes consecutively, you cannot set a different
tape speed for each programme. The first speed selected will apply to all programmes in that recording session.
b.e.s.t. The B.E.S.T. system will not work during Auto Satellite Prog Recording.
just clock Just Clock does not work when in Auto Satellite Prog Recording mode.
incoming signal The VCR will only react to the start of an incoming signal at the L-2 IN/
DECODER
receiver is powered on, the
connecter. If you try to engage Auto Satellite Prog Recording Mode whilst the satellite
SATc indicator light will flash but the VCR will not record. You must
power the satellite receiver off then on again to begin recording in these circumstances.
cable input You can record in the same way from a cable system as long as you connect the
cable system has a timer on/off function and is connected to the
incompatibilities Some satellite receivers output signals even when turned off. These receiv-
L-2 IN/DECODER connector.
ers cannot be used with this VCR in this way.
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:19 AM40
Black
advanced features 41
Editing
Editing Using Another VCR
connect up Connect the two VCRs together using a 21-pin SCART cable. If
this VCR is to be the player, connect its VCR. If this VCR is to be the recorder, you can use either the
L-2 IN/DECODER connecter to connect to the player VCR.
set recorder input mode The recording VCR mode must be set to AUX. If
this VCR is the recorder, press
IN/DECODER
VCR is the player, set
connecter) or L-2 (if you’ve used the L-1 IN/OUT connecter). If this
O.S.D. to OFF. ( pg.43)
AUX and /or PR to select L-1 (if you’ve used the L-2
set edit mode See Picture Control on page30.
start source vcr Engage its PLAY mode.
L-1 IN/OUT connecter to the recording
L-1 IN/OUT or the
start recording vcr Engage its RECORD mode.
TV Set
Video Channel or AV Mode
RF Cable
(provided)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Your VCR as the Recorder
Your VCR
ENTREE/DECODEUR IN/DECODER
21-pin SCART Cables
(not provided)
Another VCR
Your VCR
L-1L-2
010
ENTREE/DECODEUR IN/DECODER
ENTREE/SORTIE IN/OUT
010
L-1L-2
CONTROLEUR SAT
SAT CONTROL
AUDIO
ENTREE/SORTIE IN/OUT
SORTIE
R
L
OUT
ENTREE ANT. IN
ANTENNE SORTIE RF OUT
CONTROLEUR SAT
SAT CONTROL
AUDIO
ENTREE ANT. IN
SORTIE
OUT
ANTENNE
R
SORTIE RF OUT
L
RF Cable
(provided)
Your VCR as the Player
TV Set
Video Channel or AV Mode
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:19 AM41
Black
21-pin SCART Cables
(not provided)
Another VCR
advanced features42
Editing from a Camcorder
connect up Connect the Camcorder’s AUDIO/VIDEO OUT connecter to the
VCR’s rear panel cable adapter.
set input mode Press AUX or PR so that L-1 (for L-1 IN/OUT connecter) or L-2
(for L-2 IN/DECODER connecter) appears in the place of a preset position number.
set edit mode See Picture Control on page30.
start camcorder Engage the camcorder’s PLAY mode.
start recorder Press T.
L-1 IN/OUT or the L-2 IN/DECODER connecter, via an optional
Your VCR
Camcorder
ENTREE/DECODEUR IN/DECODER
VIDEO OUT
AUDIO OUT
CONTROLEUR SAT
SAT CONTROL
ENTREE/SORTIE
L-1L-2
IN/OUT
010
Cable adapter
(not provided)
Audio/Video Cable
(not provided)
ENTREE
ANT. IN
SORTIE
OUT
ANTENNE
R
SORTIE RF OUT
AUDIO
L
HR-V615/616/617EK-EN/p29-42 3/8/04, 10:19 AM42
Black
advanced features 43
Other Functions
On-Screen Display (O.S.D.)
This function allows you to turn the on-screen information ON or OFF.
get to the mode set screen Press MENU button, move
the highlight bar to buttons and press OK button (or ).
enable/disable osd The default setting for OSD is ON. Move
the highlight bar to and press OK button (or ) to toggle between
return to normal screen Press MENU button.
GUIDE TO ON-SCREEN DISPLAY INFORMATION
MODE SET using the PR and PR
OSD using the PR and PR buttons
ON and OFF.
$
#
@ !
0 9
PR.1 BBC1 t SP 21:00 NTSC a PAL
24.12.04
ST NICAM VPS/PDC
1 ¡
8 7
HIFI –1:23:45 NORM REMAIN 10:00
1
T |
MODE SET B.E.S.T. ON PICTURE CONTROL AUTO AUTO TIMER OFF
F
O.S. D. ON
DIRECT REC ON AUTO SP a LP TIMER OFF POWER SAVE OFF AUTO POWER OFF OFF
[1] a k [MENU]: EXIT
2 3
4
5 6
Operation mode
1
indicators
2 Tape speed SP/LP/EP
(EP is for NTSC only)
3 NTSC playback display 4 Tape direction 5 Counter display
HR-V615/616/617EK-EN/p43-47 3/12/04, 11:02 AM43
Black
6 Tape remaining time 7 Audio mode 8 Tape position indicator 9 VPS/PDC indicator 0 NICAM display ! Day/month/year @ Current time
# Preset position number
and station name/ Auxiliary input mode indicator (L-1 or L-2)
$ ‘Cassette Loaded’
indicator
advanced features44
Power Save Mode
You can reduce the power consumption while the VCR is turned off.
get to the mode set screen Press MENU button. Move the
highlight bar to
MODE SET using the PR and PR buttons
and press OK button (or ).
select power save mode Move the highlight bar to POWER
SAVE
using the PR and PR buttons. Press OK button
(or ) to select
ON or OFF.
F
[1] a k [MENU]: EXIT
MODE SET B.E.S.T. ON PICTURE CONTROL AUTO AUTO TIMER OFF O.S. D. ON DIRECT REC ON AUTO SP a LP TIMER OFF
POWER SAVE ON
AUTO POWER OFF OFF
return to normal screen Press MENU button.
NOTES:
• During Power Save, the display panel will be turned off.
• The Just Clock function ( pg. 54) does not work while the Power Save mode is engaged.
• While the VCR is in the Power Save mode, the picture may be distorted momentarily when you turn on/off the VCR.
• Power Save does not work when ... ... the VCR is in the Timer mode. ... the VCR’s power is turned off after timer-recording (or Instant Timer Recording). ... the Auto Satellite Prog Recording mode is engaged ( pg. 40).
Auto SP a LP Timer
When timer recording in SP mode, if the VCR calculates that there isn’t enough tape to record the complete programme, it will automatically switch from
get to the mode set screen Press MENU button. Move the
highlight bar to
MODE SET using the PR and PR buttons
and press OK button (or ).
enable/disable auto spalp timer Select AUTO SPaLP
TIMER
using the PR and PR buttons and press OK button
(or ) to toggle between
ON and OFF.
SP to LP mode.
F
[1] a k [MENU]: EXIT
MODE SET B.E.S.T. ON PICTURE CONTROL AUTO AUTO TIMER OFF O.S. D. ON DIRECT REC ON
AUTO SP a LP TIMER ON
POWER SAVE OFF AUTO POWER OFF OFF
return to normal screen Press MENU button.
HR-V615/616/617EK-EN/p43-47 3/8/04, 10:20 AM44
Black
advanced features 45
Auto Timer
When the AUTO TIMER is set to ON, the timer is automatically engaged when the VCR power is turned off and automatically disengaged when the VCR is powered back on.
get to the mode set screen Press MENU button. Move the
highlight bar to
MODE SET using the PR and PR buttons
and press OK button (or ).
enable/disable auto timer Select AUTO TIMER using the
PR and PR buttons and press OK button (or ) to toggle between
ON and OFF.
return to normal screen Press MENU button.
Auto Power Off/3H
When this function is set to “3H”, the recorder is turned off automatically if no operation is done within 3 hours. “AUTO POWER OFF IN 3 MIN” appears on the screen 3 minutes before the recorder is turned off.
get to the mode set screen Press MENU button. Move the
highlight bar to and press OK button (or ).
select auto power mode Move the highlight bar to AUTO
POWER
using the PR and PR buttons . Press OK button (or ) to select 3H or OFF.
MODE SET using the PR and PR buttons
MODE SET B.E.S.T. ON PICTURE CONTROL AUTO
F
AUTO TIMER ON
O.S. D. ON DIRECT REC ON AUTO SP a LP TIMER OFF POWER SAVE OFF AUTO POWER OFF OFF
[1] a k [MENU]: EXIT
MODE SET B.E.S.T. ON PICTURE CONTROL AUTO AUTO TIMERER ON O.S. D. ON DIRECT REC ON AUTO SP a LP TIMER OFF POWER SAVE OFF
F
AUTO POWER OFF 3H
[1] a k [MENU]: EXIT
return to normal screen Press MENU button.
Repeat Playback
start repeat playback Press ., then press and hold . again for over 5 seconds, then release.
The Play indicator (
#) will flash on the display panel and the VCR will automatically playback
and rewind the tape 100 times and then stop.
stop playback Pressing S, ., < or > stops repeat playback.
Next Function Memory
play To playback immediately after rewinding, press < and then . within 2seconds.
power off To power off the VCR immediately after rewinding, press < and then o
within 2seconds.
timer standby To put the VCR in timer standby mode immediately after rewinding, press
< and then c within 2seconds.
HR-V615/616/617EK-EN/p43-47 3/8/04, 10:20 AM45
Black
advanced features46
Connection to a Stereo System
It is possible to connect your VCR to a suitably equipped stereo system and listen to the soundtrack through the stereo system.
connect up Connect the AUDIO OUT L and R connecters on the VCR to the AUX IN or TAPE MONITOR
connecters on your stereo. See diagram below.
FM Tuner
CD Player
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
Stereo Amplifier
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
AUX IN or TAPE MONITOR
Audio Cable
(not provided)
Speaker
Television
Speaker
ENTREE/DECODEUR IN/DECODER
010
ENTREE/SORTIE
L-1L-2
IN/OUT
CONTROLEUR SAT
SORTIE
SAT CONTROL
R
AUDIO
L
ENTREE ANT. IN
OUT
ANTENNE
SORTIE RF OUT
Back of VCR
Mains Outlet
*DECODER function is not available in the UK.
AUDIO OUT
NOTES ON STEREO CONNECTIONS
speaker connections Make sure that you connect the L and R speakers in the right order.
nicam tv If you can receive NICAM TV broadcasts in your area, this VCR can record them indepen-
dently of the TV set and play them back through the stereo.
volume When listening to sound through the connected stereo, turn the TV’s volume down to zero.
dynamic range This VCR has a Hi-Fi audio dynamic range of 80 dB. Check that your stereo is
capable of handling this level of input. If it cannot, you risk speaker damage.
HR-V615/616/617EK-EN/p43-47 3/8/04, 10:20 AM46
Black
advanced features 47
Video Channel Set
before you start
The power cord must be
plugged in and
connected to the VCR
The VCR must be turned
off and no cassette
inserted
The Remote Control
must have the battery
inserted
The TV set must be
turned on
The VCR can send picture signals to the TV set in one of two ways; RF (ordinary cable included with this VCR) and AV (via a 21-pin SCART cable available from TV and Hi-Fi dealers). Depending upon which method you use, the VCR must have the correct method set up in order to work. The Auto Setup procedure normally takes care of this but if for any reason this fails to happen, the instructions below describe how to set the Video Channel manually.
Access Video Channel Mode
Press and hold the S button for 5 seconds on the VCR until the display panel shows the following information:
VCR
SAT
REVIEW
Set Video Channel
for av connection Press PR button until
the display panel shows: The Video Channel is now set to
Step 3.
Go to
OFF.
VCR
SAT
REVIEW
for rf connection Press PR or PR
button to set the VCR to a vacant channel number between 52 and 69 which is not occu-
VCR
SAT
REVIEW
pied by any station in your area (refer to station list on page53). In the example, we have presumed that channel 52 is vacant and
have set the VCR to 52:
Now tune the TV set to channel 52 (refer to TV manual if necessary); you should see two vertical white bars appear on the TV screen. If the bars do not appear or are not clear, choose another vacant channel and try again. If you cannot obtain the vertical white bars on any channel between 52 and 69, consult your local JVC dealer.
Exit Video Channel Set Mode
Press OK button .
To view pictures from your VCR you must now set your TV to either the Video Channel or to AV mode, depending upon your choice above.
HR-V615/616/617EK-EN/p43-47 3/8/04, 10:20 AM47
Black
advanced features48
Tuner Set
The VCR needs to find, identify and memorise all available stations in your area in order to record programmes correctly. Once done, pressing the PR or PR buttons enables you to jump to the available channels without going via any vacant channels. This channel search can be done either automatically or manually. You should only need to perform either of the following procedures if Auto Setup or Preset Download has failed to identify and record available channels or you have moved to a new area.
Auto Channel Setup
get to the main menu Press MENU button.
perform auto channel set Move the highlight bar to AUTO CH
SET
using the PR and PR buttons and press OK button
(or ) twice.
rf and scart connection If you have chosen to connect the
MAIN MENU
MODE SET
F
AUTO CH SET
MANUAL CH SET INITIAL SET
[1] a k [MENU]: EXIT
VCR to the TV with both the RF Cable and a 21-pin SCART Cable (not provided) and the TV set is in its AV mode (see the TV manual), the
AUTO SET screen will appear on the TV and remains
there for about 4–12 minutes while the VCR searches for receivable stations. During Auto
S
Channel Set the
mark on the screen moves from left to right.
note: If you have connected both the RF cable and the fully-wired 21-pin SCART cable, and if your TV offers T-V Link, etc., and the
AUTO SET
PLEASE WAIT
TV is turned on, the VCR automatically performs the Preset Download (pg. 11) even if you select “Auto’ for Auto Setup function.
[MENU]:EXIT
The caption
SCAN COMPLETED appears at the end of the process for
about 5 seconds.
confirmation screen Once Auto Channel Set has completed its
search, the confirmation screen will appear showing the details
PR = Preset Number, CH = Channel Number and ID = Station
( Name) of the TV stations that the process has found. The first station will have a highlight bar over it and will be blinking. This screen and the programme currently being broadcast on the selected station will alternate at 8second intervals. To view the next channel, press the PR and PR buttons to move the highlight bar to the required channel.
CH
PR
26
01
33
02
23
03
30
04
37
05 06 07
[10]
a k: EDIT a [x]: DELETE
[MENU]: EXIT
BBC1
BBC2
ITV CH4 CH5
- - - -
- - - -
PR
ID
08
09 10 11 12 13 14
CH ID
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
- - - -
return to normal screen Press MENU button.
NOTES ON CHANNEL RECEPTION
incorrect station id In certain reception conditions, station
names may not be stored correctly by the VCR and Auto Guide Program Number Set may not work properly. If the Guide Program Numbers are not set, entering a PlusCode number, may result in an incorrect channel being recorded.
poor reception The VCR memorises all stations found regardless of their quality. If a station’s
quality is poor, you can delete that station from the memory (see page 50).
HR-V615/616/617EK-EN/p48-53 3/8/04, 10:21 AM48
Black
Manual Channel Setup
advanced features 49
get to the confirmation screen Press MENU button. Move
the highlight bar to
MANUAL CH SET using the PR and PR
buttons and press OK button (or ).
MAIN MENU
MODE SET
AUTO CH SET
F
MANUAL CH SET
INITIAL SET
[1] a k [MENU]: EXIT
select position Use the PR button on the Remote Control to move the highlight bar to a
vacant position then press OK button.
CH
PR
26
01
33
02
23
03
30
04
37
05
06
07 [10]
a k: EDIT a [x]: DELETE
[MENU]: EXIT
BBC1 BBC2
ITV CH4 CH5
- - - -
- - - -
ID
- - - -
08
- - - -
09
- - - -
10
- - - -
11
- - - -
12
- - - -
13
- - - -
14
CH ID
PR
In this example, we have chosen position6.
select band When the
MANUAL CH SET screen appears,
press the PR and PR buttons to change the band between CH (regular) and CC (cable).
PR
06
[1]: SELECT [0]: CURSOR g k: OK [MENU]: EXIT
CH
CH01
- - - -
ID
FINE
+/–
input channel number
Press the button and you will see the channel number space flashing. Use the number keys to enter the Channel Number that you want to store.
input channel id Press the button to move to the Channel ID space and use the PR and
PR buttons to select the required ID from the stored list.
fine tuning Press the button repeatedly to move to the Fine Tuning ‘+/–’ and use the PR
and PR buttons to fine-tune the channel. A ‘+’ or a ‘–’ symbol will appear during this process.
save new channel details Press OK button to save the details you have just entered. The
Confirmation Screen will appear again. Repeat the above procedure from
Select Position onwards
as many times as required.
close confirmation screen Press MENU button.
HR-V615/616/617EK-EN/p48-53 3/8/04, 10:21 AM49
Black
advanced features50
Change Station Name
get to the confirmation screen Press MENU button. Move the highlight bar to MANUAL
CH SET
using the PR and PR buttons and press OK button (or ).
select position Use the PR buttons on the Remote Control to move the highlight bar to the
preset position you want then press OK button twice.
select character Press until the first letter of the station name begins blinking.
enter new character Press the PR and PR buttons to cycle through the characters (A–Z, 0–9, –, when the desired character is indicated, then press to enter.
, +, (space)) and stop
*
PR06CH
CH45IDBBC1
[0–9]: A–Z, 0–9 [0]: CURSOR g k: OK [MENU]: EXIT
FINE
+/–
Enter the remaining characters the same way (maximum of 4). After entering all characters, press OK button.
• The Confirmation screen appears.
• If you make a mistake, press until the incorrect character begins blinking. Then enter the correct character by pressing the PR and PR buttons.
close confirmation screen Press MENU button.
Delete a Channel
get to the confirmation screen Press MENU button. Move the highlight bar to MANUAL
CH SET
using the PR and PR buttons and press OK button (or ).
select channel Use the PR buttons on the Remote Control
to move the highlight bar to the channel that you wish to delete.
delete channel Press x.
return to normal screen Press MENU button.
CH
PR
26
01
33
02
23
03
30
04
37
05 06 07
[10]
a k: EDIT a [x]: DELETE
[MENU]: EXIT
BBC1 BBC2
ITV
CH4
CH5
- - - -
- - - -
ID
CH ID
PR
- - - -
08
- - - -
09
- - - -
10
- - - -
11
- - - -
12
- - - -
13
- - - -
14
HR-V615/616/617EK-EN/p48-53 3/8/04, 10:21 AM50
Black
advanced features 51
Change Station Preset Position
get to the confirmation screen Press MENU button. Move the highlight bar to MANUAL
CH SET
using the PR and PR buttons and press OK button (or ).
select item Use the PR buttons on the Remote Control until the item you want to move
begins blinking then press OK button. The station name (ID) and its channel (CH) number
begin blinking.
select new position Use the PR buttons to move the station to the new preset position, then
press OK button.
Example: If you moved the
PR 01 02 03
04
05 06 07
[10]: MOVE k: MANUAL CH SET [MENU]: EXIT
BBC1
26
ITV
23
CH4
30
BBC2
33
CH5
37
– – – – – – – –
ID
CH
CH ID
PR
– – – –
08
– – – –
09
– – – –
10
– – – –
11
– – – –
12
– – – –
13
– – – –
14
PR 01
02
03 04 05 06 07
[10]: MOVE a k [MENU]: EXIT
BBC1
26
BBC2
33
ITV
23
CH4
30
CH5
37
– – – – – – – –
– – – –
08
– – – –
09
– – – –
10
– – – –
11
– – – –
12
– – – –
13
– – – –
14
CH ID
PR
ID
CH
station in position 4 to position 2, the stations originally in positions 2 and 3 each move down one space.
close confirmation screen Press MENU button.
HR-V615/616/617EK-EN/p48-53 3/8/04, 10:21 AM51
Black
advanced features52
Fine-Tuning Stored Channels
get to the confirmation screen Press MENU button. Move the highlight bar to MANUAL CH
SET
using the PR and PR buttons and press OK button (or ).
select item Use the PR button on the Remote Control to move the highlight bar to the channel
that you wish to fine-tune then press OK button twice.
fine tuning Press the button to move to the Fine Tuning ‘+/–’ and use the PR and PR
buttons to fine-tune the channel. A ‘+’ or a ‘–’ symbol will appear during this process.
save new details Press OK button to save the details you have just entered. The Confirmation
Screen will appear again.
close confirmation screen Press MENU button.
TV Station ID Guide
STATION NAME ID
Anglia TV ANGL ARD ARD ARTE ARTE BBC Group BBC BBC1 BBC1 BBC2 BBC2 BBC World BBCW Berlin 1 BLN1 Berlin 2 BLN2 Border TV BORD Bayern1 BR1 Bayern3 BR3 BRT1 BRT1 BRT2 BRT2 Children Ch CHLD Canal + CH+ CNN CNN Channel TV CHNL Central TV CNTR Channel 4 CH 4 Channel 5 CH 5 Discovery DRS DRS DR TV DRTV DSF DSF Euronews EURN Euronews EURO Eurosports EURS France1 FR1 France2 FR2 France3 FR3
STATION NAME ID
Granada TV GRNA Grampian TV GRMP Hessen1 HR1 Hessen3 HR3 HRT HRT HTV HTV ITV Network ITV Kabelkanal KABL London LNDN MDR MDR MTV MTV Nord3 N3 NDR1 NDR1 NDR3 NDR3 NED1 NED1 NED2 NED2 NED3 NED3 Network 2 NET2 NRK NRK N-TV N-TV Offener Kanal OKAN ORF1 ORF1 ORF2 ORF2 ORF3 ORF3 OWL 3 OWL3 Premiere PRMI PR07 PR07 RAI1 RAI1 RAI2 RAI2 RAI3 RAI3 RB1 RB1
STATION NAME ID
RB3 RB3 Rikisutvarpid-S RKPS RTBF 1 RTB1 RTBF 2 RTB2 RTE 1 RTE1 RTL RTL RTL 2 RTL2 RTP RTP SAT SAT SAT 1 SAT1 Scottish TV SCOT SC4 SC4 SDR SDR SDR1 SDR1 SFB1 SFB1 SFB3 SFB3 SKY SKY Sky One SKY1 Sky Net SKYN Sport SPRT SR 1 SR1 Super RTL SRTL STV Test STVT STV 1 STV1 STV 2 STV2 Suedwest3 SWR SWF 1 SWF1 Schweiz4 SWZ4 TYNE TEES TEES Text TEXT TF1 TF1
STATION NAME ID
TNT int TNT TRT int TRT TSI TSI TSR TSR TSW TSW TVE TVE TV Polonia TVPA TVP 1 TVP1 TVP 2 TVP2 TVS TVS TV2 TV2 TV5 TV5 Tele Zurich TZUR Ulster TV ULST Veronica VERN VIVA VIVA VIVA2 VIV2 VOX VOX VTM VTM VT4 VT4 West1 WDR1 West3 WDR3 YLE 1 YLE1 YLE 2 YLE2 Yorkshire TV YORK ZDF ZDF Zurich 1 ZUR1 3SAT 3SAT
HR-V615/616/617EK-EN/p48-53 3/8/04, 10:21 AM52
Black
TV Station Channel Number Guide
Region Transmitter BBC1 BBC2 ITV CH4 CH5
London & South-East
Bluebell Hill 40 46 43 65 — Crystal Palace 26 33 23 30 37 Dover 50566653— Heathfield 49 52 64 67 — Oxford 57 63 60 53 49
South-West
Beacon Hill 57 63 60 53 — Caradon Hill 22 28 25 32 — Huntshaw Cross 55 62 59 65 67 Redruth 51 44 41 47 37 Stockland Hill 33 26 23 29 — Channel Islands Fremont Point 51 44 41 47
South
Hannington 39 45 42 66 35 Midhurst 61 55 58 68 — Rowridge 31 24 27 21
West
Mendip 58 64 61 54 37
East
Sandy Heath 31 27 24 21 39 Sudbury 51 44 41 47 35 Tacolneston 62 55 59 65 52
Midlands
Ridge Hill 22 28 25 32 35 Sutton Coldfield 46 40 43 50 37 The Wrekin 26 33 23 29 35 Waltham 58 64 61 54 35
North
Belmont 22 28 25 32 56 Emley Moor 44 51 47 41 37
North-West
Caldbeck 30 34 28 32 56 Winter Hill 55 62 59 65 48
North-East
Bilsdale West Moor 33 26 29 23 35 Chatton 39 45 49 42 — Pontop Pike 58 64 61 54 68
Scotland
Angus 57 63 60 53 — Black Hill 40 46 43 50 37 Sandale 22 — Caldbeck 34 28 32 56 Creigkelly 31 27 24 21 48 Darvel 3326232935 Durris 22 28 25 32 67 Eitshal 33 26 23 29 — Keelylang Hill 40 46 43 50 — Knock More 33 26 23 29 — Rosemarkie 39 45 49 42 67 Rumster Forest 31 27 24 21 — Selkirk 55 62 59 65 52
Wales
Blaenplwyf 31 27 24 21 56 Carmel 57 63 60 53 — Llanddona 57 63 60 53 — Moel-y-Parc 52454942— Presely 46 40 43 50 37 Wenvoe 44 51 41 47
Northern Ireland
Brougher Mountain 22 28 25 32 — Divis 31 27 24 21 37 Limavady 55 62 59 65
advanced features 53
HR-V615/616/617EK-EN/p48-53 3/8/04, 10:21 AM53
Black
advanced features54
Clock Set
You should only need to perform this function if:
• Auto Clock Set was not performed correctly by Auto Setup, Preset Download or Auto Channel Set
• The VCR’s memory backup has expired
• You want to change the Just Clock setting
Setting the Clock
get to the initial set screen Press MENU button. Move the highlight bar to INITIAL SET
using the PR and PR buttons and press OK button (or ).
get to the clock set screen Move the highlight bar to CLOCK SET using the PR and
PR buttons and press OK button (or ).
set time and date When the CLOCK SET screen appears, the time will be blinking. Use the
PR and PR buttons to set the correct time (pressing and holding will advance the time in 30minute increments) and then
press OK button (or ). The date will blink. Use the PR and PR buttons to set the correct date (pressing and holding will advance the date in 15day increments) and then press OK button (or ). Set the correct year in the same way and press OK button.
set just clock Set as desired using the PR and PR
buttons then press OK button (or ).
TIME DATE YEAR
0: 00 01 . 01 03
[1] a k [MENU]: EXIT
CLOCK SET
JUST CLOCK : ON TV PR. : 1
set preset for clock data source If you have set JUST CLOCK to ON, you will need to
specify a preset (station) for
JUST CLOCK to take its source data from. Use the PR and PR
buttons to select the preset and press OK button (or ).
start clock operation Press MENU button.
NOTE:
If the recorder’s memory backup has expired or the AC was disconnected from the recorder, the recorder will automatically perform Auto Clock Set when the power is restored.
Notes on Just Clock
Some TV stations transmit a time signal with their broadcasts. This VCR has the ability to use this signal to update its internal clock (including the adjustment for British Summer Time). It will do this every hour except for 23:00, 00:00, 01:00 and 02:00. By setting Just Clock to enabling the VCR to do this. Just Clock is not effective in the following circumstances:
• when the VCR is powered on
• when the VCR is in Timer or Auto Satellite Programme Recording modes
• when a difference of more than 3minutes between the internal clock and the time signal exists.
• when reception conditions are poor.
ON, you are
HR-V615/616/617EK-EN/p54-59 3/12/04, 10:58 AM54
Black
subsidiary information 55
Question and Answers
PLAYBACK
Q: What happens if the end of the tape is
reached during playback or search?
A: The tape is automatically rewound to the
beginning.
Q: Can the VCR indefinitely remain in the
still mode?
A: No. It stops automatically after 5minutes
to protect the heads.
Q: During search, slow, still and frame-by-
frame playback, I can’t hear any audio. What’s the problem?
A: This is normal.
Q: When returning from variable-speed
search to normal playback, the picture is disturbed. Should I be concerned about this?
A: No, it is normal.
Q: Noise bars appear during variable-speed
search. What’s the problem?
A: This is normal.
Q: Sometimes, during Index Search, the
VCR can’t find the programme I want to see. Why not?
A: There may be index codes too close
together.
RECORDING
Q: When I pause and then resume a
recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?
A: This is normal. It reduces distortion at the
pause and resume points.
Q: Can the VCR indefinitely remain in the
Record-Pause mode?
A: No. The VCR shuts off automatically after
5minutes to protect the heads.
Q: What happens if the tape runs out
during recording?
A:The VCR stops recording, then if Timer
Recording, the VCR shuts off.
TIMER RECORDING
Q: U and c remain lit on the display panel.
Is there a problem?
A: No. This is a normal condition for a timer
recording in progress.
Q: Can I programme the timer while I’m
watching a tape or a TV broadcast?
A: You won’t see the picture as it is replaced
by the on-screen menu, but the audio from the program or tape you’re viewing can be heard.
HR-V615/616/617EK-EN/p54-59 3/8/04, 10:22 AM55
Black
subsidiary information56
Troubleshooting
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
POWER
1. No power is applied to the VCR.
• The mains power cord is disconnected.
Connect the mains power cord.
2. The clock is functioning properly, but the VCR cannot be powered.
3. The Remote Control won’t function.
TAPE TRANSPORT
1. The tape does not run during recording. U lights up and preset position blinks on the display panel.
2. The tape will not rewind or fast­forward.
PLAYBACK
1. The playback picture does not appear while the tape is running.
c is displayed on the display panel with AUTO TIMER set to OFF.
• The batteries are discharged.
• The VCR is in the RECORD PAUSE MODE.
• The tape is already fully rewound or fast-forwarded.
• If you’re using only the RF cable for connection… …the TV’s channel selector is not set to the Video Channel. …the VCR’s Video Channel has not been correctly set.
• If you’re using both the RF cable and 21-pin SCART cable for connection, the TV is not set to the AV mode.
Press the c button to turn the c indicator off.
Replace the dead new one.
Press . to resume recording.
Check the cassette.
If you are using only the RF cable for connection… …set the TV to the Video Channel. …Perform Video Channel Set. (pg.47)
If you are using both the RF cable and 21-pin SCART cable for connection, set the TV to its AV mode.
battery with a
2. Noise appears during visual search.
3. Noise appears during normal playback.
4. The playback picture is blurred or interrupted while TV broad­casts are clear or USE CLEAN- ING CASSETTE message appears on the screen.
5. Breaks are noticeable in Hi-Fi soundtrack.
HR-V615/616/617EK-EN/p54-59 3/8/04, 10:22 AM56
Black
• This is normal.
• The automatic tracking mode is engaged.
• The video heads may be dirty.
• Automatic tracking is engaged.
Try manual tracking. ( pg. 28)
Use a dry cleaning cassette JVC TCL-2 or consult your JVC dealer.
Try manual tracking (墌 pg. 30) or press AUDIO to change the soundtrack to NORM (pg.32).
subsidiary information 57
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
RECORDING
1. Recording cannot be started.
• There is no cassette loaded, or the cassette loaded has had its record safety tab removed.
Insert a cassette, or using adhesive tape, cover the hole where the tab was removed.
2. TV broadcasts cannot be recorded.
3. Tape-to-tape editing is not possible.
4. Camcorder recording is not possible.
TIMER RECORDING
1. Timer recording won’t work.
2. Timer programming is not possible.
• L-1 or L-2 has been selected as the input mode.
• The source (another VCR, camcorder) has not been properly connected.
• All necessary power switches have not been turned on.
• The input mode is not correct.
• The camcorder has not been properly connected.
• The input mode is not correct.
• The clock and/or the timer have been set incorrectly.
• The timer is not engaged.
• Timer recording is in progress.
Set to the desired preset.
Confirm that the source is prop­erly connected.
Confirm that all units’ power switches are turned on. Set the input mode to L-1 or L-2.
Confirm that the camcorder is properly connected. Set the input mode to L-1 or L-2.
Re-perform the clock and/or timer settings. Press c and confirm that c is displayed on the display panel.
Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.
3. c on the display panel won’t stop blinking.
4. c, U and , on the display panel won’t stop blinking.
5. c blinks for 10 seconds and the Timer mode is disengaged.
6. The VIDEO Plus+ system does not timer record properly.
• The timer is engaged but there’s no cassette loaded.
• The loaded cassette has had its record safety tab removed.
• The end of the tape was reached during timer recording.
c has been pressed when there are no programs in memory, or the timer record information has been pro­grammed incorrectly.
• The VCR’s preset positions have been set incorrectly.
Load a cassette with the record safety tab intact.
Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact. The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.
Check the programmed data and re-programme as necessary, then press c again.
Refer to Set Guide Program Numbers (墌 pg. 22) and re- perform the procedure.
HR-V615/616/617EK-EN/p54-59 3/8/04, 10:22 AM57
Black
subsidiary information58
SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION
TIMER RECORDING (cont.)
7. U, , and the SATc indicator won’t stop blinking.
• The loaded cassette has had its record safety tab removed.
Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.
8. U and , on the display panel won’t stop blinking.
OTHER PROBLEMS
1. Whistling or howling is heard from the TV during camcorder recording.
2. When scanning channels, some of them are skipped over.
3. The preset cannot be changed.
4. Channel settings that were made manually seem to have changed or disappeared.
• The end of the tape was reached during Auto Satellite Programme Recording.
• The end of the tape was reached during Instant Timer Recording.
• The camcorder’s microphone is too close to the TV.
• The TV’s volume is too high.
• Those channels have been designated to be skipped.
• Recording is in progress.
• After the manual settings were made, Auto Channel Set was performed.
The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.
The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.
Position the camcorder so its microphone is away from the TV. Turn the TV’s volume down.
If you need the skipped channels, restore them.
Press | to pause the recording, change presets, then press . to resume recording.
Perform manual setting again.
5. No channels are stored in the VCR’s memory.
HR-V615/616/617EK-EN/p54-59 3/8/04, 10:22 AM58
Black
• The TV aerial cable was not connected to the VCR when Auto Set Up was performed.
• The fully-wired 21-pin SCART cable was not connected between TV and the VCR when Preset Download was per­formed.
Turn off the VCR once and connect the TV aerial cable to the VCR properly, then turn on the VCR again. Then perform Auto Setup again (墌pg.10). Turn off the VCR once and connect the fully-wired 21-pin SCART cable to the VCR properly, then turn on the VCR again. Then perform Preset Download again (pg.11).
List of Terms
AA
A
AA
Auto Channel Setup ................................................. 48
Auto Power ............................................................... 45
Auto Satellite Programme Recording ...................... 39
Auto Setup ................................................................ 10
Auto SP a LP Timer ................................................44
Auto Timer ............................................................... 45
BB
B
BB
B.E.S.T. ...................................................................... 31
CC
C
CC
Change Station Name .............................................. 50
Change Station Preset Position ................................ 51
Clock Set ................................................................... 54
Connection to a Stereo System ............................... 46
Counter Display................................................. 19, 43
DD
D
DD
Delete a Channel ....................................................... 50
Direct Rec .................................................................. 35
EE
E
EE
Editing ....................................................................... 41
Editing from a Camcorder .......................................42
Editing Using Another VCR .................................... 41
Express Timer Programming ................................... 24
FF
F
FF
Fine-Tuning Stored Channels.................................. 52
II
I
II
Index Search.............................................................. 33
Instant ReView.......................................................... 33
Instant Timer Recording ......................................... 20
JJ
J
JJ
Just Clock .................................................................. 54
MM
M
MM
Manual Channel Setup ............................................ 49
Manual Tracking ...................................................... 30
NN
N
NN
Next Function Memory ........................................... 45
NICAM Stereo and Bilingual Broadcasts ................ 32
NTSC Tapes .............................................................. 14
OO
O
OO
On-Screen Display (O.S.D.)..................................... 43
PP
P
PP
Pause During Playback ............................................. 16
Picture Control .........................................................30
Picture Search ........................................................... 17
Playback .................................................................... 14
PlusCode Number .................................................... 21
Power Save Mode ..................................................... 44
Preset Download........................................................ 11
RR
R
RR
Record a Programme While Watching Another .... 19
Recording .................................................................. 18
Recording Resume Function ................................... 20
Repeat Playback ........................................................ 45
SS
S
SS
Satellite Controller.................................................... 36
Satellite Receiver Control Settings ........................... 36
Single Frame Movement .......................................... 16
Skip Search ................................................................ 33
Slow Motion ............................................................. 17
Soundtrack Selection ................................................ 32
SQPB ......................................................................... 15
TT
T
TT
Tape Remaining Time ....................................... 19, 43
Tuner Set ...................................................................48
TV Station Channel Number Guide ....................... 53
TV Station ID Guide ................................................ 52
VV
V
VV
Variable Speed Search .............................................. 17
Video Channel Set .................................................... 47
Video Heads Cleaning .............................................. 15
VIDEO Plus+® Timer Programming ...................... 21
HR-V615/616/617EK-EN/p54-59 3/12/04, 10:58 AM59
Black
s p e c i f i c a t i o n s
g e n e r a l
Power requirement : AC 220 V – 240 V
Power consumption : on : 14 W, off : 3.2 W
Operating Temperature : 5°C to 40°C Storage Temperature: –20°C to 60°C
Operating position : Horizontal only
Dimensions (WxHxD) : 400 mm x 94 mm x 275 mm
Weight : 3.1 kg
Format : VHS PAL standard
Maximum recording time : (SP) : 240 min. with E-240 video cassette (LP) : 480 min. with E-240 video cassette
v i d e o / a u d i o
Signal system : PAL-type colour signal and CCIR monochrome signal, 625 lines/50 fields
Recording system : DA4 (Double Azimuth) helical scan system
Signal-to-noise ratio : 45 dB
Horizontal resolution : 250 lines
Frequency range : 70 Hz to 10,000 Hz (Normal audio)
20 Hz to 20,000 Hz (Hi-Fi audio)
Input/Output : 21-pin SCART connectors
(IN/OUT x 1, IN/DECODER x 1)
RCA connectors
(AUDIO OUT x 1)
, 50 Hz/60 Hz
Ó
HR-V615/616/617EK
t u n e r / t i m e r
TV channel storage capacity : 99 positions (+AUX position)
Tuning system :Frequency synthesized tuner
Channel coverage : VHF 44.5 MHz – 143 MHz/
143 MHz – 470 MHz/
UHF 470 MHz – 862 MHz
Aerial output : UHF channels 22 – 69 (Adjustable)
Memory backup time : Approx. 10 min.
a c c e s s o r i e s
Provided accessories : RF cable, Infrared remote control unit, “AA” Battery x 2
Specifications shown are for SP mode unless otherwise specified.
E.& O.E. Design and specifications subject to change without notice.
COPYRIGHT © 2004 VICTOR COMPANY OF JAPAN, LTD.
HR-V615/616/617EK-EN/p60Back 3/12/04, 03:34 PM60
Black
VICTOR COMPANY OF JAPAN, LIMITED
Printed in China
EK
0304-MAR-YL-VM
Loading...