JVC HR-S5400U User Manual

VIDEO CASSETTE RECORDER

HR-S5400U

TV, CABLE / DBS operation – Press and hold  TV CABLE/DBS button, then press POWER, CH 5/∞, TV/VCR, 0 – 9, ENTER

CABLE/DBS

A/BTV

POWER

TV/VCR

LIVE

456

SURROUND

MBR SET



DAILY

WEEKLY

DISPLAY

ENTER SP/EP

TIMER

AUX

OSD

C.MEMORY

CANCEL

ADD

C.RESET/CH.SKIP

TV VOL

SKIP SEARCH

REW

PLAY1FF

REC

STOP8PAUSE

4¢

SHUTTLE PLUS

POWER

MENU CH OK

(

VIDEO

MONO)L – AUDIO – R

LIVE SURROUND

SP/EP

L R

VCR

SAP ST

REC

PLAY

6 10

PAUSE

–20dB

TIMER

HMS

NORM

INSERT

A. DUB

REC

PAUSE

REW FF

STOP/EJECT PLAY



JOG

SHUTTLE

INSTRUCTIONS

For Customer Use:

Enter below the Model No. and Serial No. which are located on the rear of cabinet. Retain this information for future reference.  Model No. 



Serial No.

LPT0002-016B

2 EN

Dear Customer,

Thank you for purchasing the JVC VHS video cassette recorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of your new VCR.

Failure to heed the following precautions may result in

CAUTIONS

CAUTION



RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION:

This video cassette recorder should be used with AC 120V`, 60Hz only. To prevent electric shocks and fire hazards, DO NOT use any other power source.

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

damage to the VCR, remote control or video cassette.

1. DO NOT place the VCR . . .

... in an environment prone to extreme temperatures or

humidity. ... in direct sunlight. ... in a dusty environment. ... in an environment where strong magnetic fields are

generated. ... on a surface that is unstable or subject to vibration.

2. DO NOT block the VCR’s ventilation openings.

3. DO NOT place heavy objects on the VCR or remote control.

4. DO NOT place anything which might spill on top of the VCR or remote control.

5. AVOID violent shocks to the VCR during transport.

**MOISTURE CONDENSATION

Moisture in the air will condense on the VCR when you move it from a cold place to a warm place, or under extremely humid conditions—just as water droplets form on the surface of a glass filled with cold liquid. Moisture condensation on the head drum will cause damage to the tape. In conditions where condensation may occur, keep the VCR’s power turned on for a few hours to let the moisture dry before inserting a tape.

**ABOUT HEAD CLEANING

Accumulation of dirt and other particles on the video heads may cause the playback picture to become blurred or interrupted. Be sure to contact your nearest JVC dealer if such troubles occur.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU'AU FOND.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

CAUTION:

Changes or modifications not approved by JVC could void user's authority to operate the equipment.

VCR Plus+C3 and PlusCode are trademarks of Gemstar Development Corporation. The VCR Plus+ system is manufactured under license from Gemstar Development Corporation.

DSS

is an official trademark of DIRECTV, Inc., a unit of GM Hughes Electronics. PRIMESTAR is a registered service mark of Primestar Partners, L.P. DISH Network Echostar Communications Corporation.

n Cassettes marked "S-VHS" and "VHS" can be used with this

video cassette recorder. However, S-VHS recordings are possible only with cassettes marked "S-VHS".

is a trademark of

EN 3

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this booklet for future reference.

INSTALLATION

1. Grounding or Polarization

(A) Your product may be equipped with a polarized alternating-

current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

(B) Your product may be equipped with a 3-wire grounding-type

plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

2. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

3. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

4. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

5. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

• Do not block the openings by placing the product on a bed,

sofa, rug or other similar surface.

• Do not place the product in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

6. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT (NEC SECTION 

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

810-20)

GROUNDING  CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

4 EN

USE

1. Accessories

To avoid personal injury:

• Do not place this product on an unstable cart, stand, tripod, bracket, or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.

• Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.

• Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.

• Do not try to roll a cart with small casters across thresholds or deep-pile carpets.

2. Product and Cart Combination

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

3. Water and Moisture

Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

4. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

PORTABLE CART WARNING (Symbol provided by RETAC)

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a.When the power supply cord or plug is damaged. b.If liquid has been spilled, or objects have fallen into the

product. c.If the product has been exposed to rain or water. d.If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and will

often require extensive work by a qualified technician to

restore the product to its normal operation. e.If the product has been dropped or damaged in any way. f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.

HOW TO USE THIS INSTRUCTION MANUAL

● All major sections and subsections are listed in the Table Of

Contents on page 5. Use this when searching for information

on a specific procedure or feature.

● The Index on pages 64–67 lists frequently-used terms, and

the number of the page on which they are used or explained

in the manual. This section also illustrates the controls and

connections on the front and rear panel, the front display

panel and the remote control.

● The Z mark signals a reference to another page for

instructions or related information.

● Operation buttons necessary for the various procedures are

clearly indicated through the use of illustrations at the

beginning of each major section.

BEFORE YOU INSTALL YOUR NEW VCR . . .

. . . please read the sections/literature listed below.

● ”Cautions” on page 2

● ”Important Products Safety Instructions” on the previous pages

CONTENTS

NSTALLING YOUR NEW VCR 6

Connections ........................................... 6

Basic Connections .....................................................6

S-VIDEO Connection .................................................7

NITIAL SETTINGS 8

Plug & Play .................................................. 8

Language ................................................... 10

Clock .......................................................... 11

Preparation ..............................................................11

Semi-Auto................................................................12

Manual ....................................................................13

Auto ........................................................................ 13

Tuner .......................................................... 14

Set Receivable Channels ..........................................14

Add Or Delete A Channel ........................................16

Cable Box Control ....................................... 17

Situate And Connect Controller ............................... 17

Set Cable Box Output Channel ................................18

Set Cable Box Brand ................................................19

VCR Plus+ Setup ......................................... 20

DBS Receiver Control................................... 22

Situate And Connect Controller ............................... 22

Set DBS Receiver Output Channel ...........................23

Set DBS Receiver Brand ...........................................24

IMPLE PLAYBACK AND

RECORDING 25

Simple Playback .........................................25

Simple Recording ........................................ 26

LAYBACK AND RECORDING FEATURES 27

Playback Features ...................................... 27

Still Picture/Frame-By-Frame Playback.....................27

Slow Motion/Reverse Slow Motion ..........................27

Variable-Speed Search/Reverse Motion Playback .....27

High-Speed Search ..................................................28

Manual Tracking ......................................................28

Tape Position Indicator ............................................28

Video Stabilizer .......................................................29

Superimpose ............................................................30

Select The Soundtrack ............................................. 31

Index Search ............................................................32

Instant ReView.........................................................32

Skip Search ..............................................................32

Live Surround ..........................................................32

Repeat Playback ......................................................33

Counter Reset ..........................................................33

Counter Memory ..................................................... 33

Next-Function Memory............................................33

AV COMPU LINK Playback .....................................34

Active Video Calibration ............................. 36

Preparation ..............................................................36

Recording ................................................................37

Playback ..................................................................37

Recording Features .....................................38

Record One Program While

Watching Another....................................................38

Display Elapsed Recording Time..............................38

EN 5

Dispiay Tape Remaining Time .................................38

S-VHS (Super VHS) and VHS ...................................39

Stereo And SAP (Second Audio Program) .................40

To Record SAP Programs..........................................40

Hi-Fi Audio Recording Level Control .......................41

IMER RECORDING 42

VCR Plus+ Timer Programming ................... 42

On-Screen Timer Programming ...................44

Check And Cancel Programs ................................... 46

Auto Timer............................................................... 47

Instant Timer Recording (ITR)....................... 48

DITING 49

Edit To Or From Another VCR ...................... 49

Edit From A Camcorder ...............................50

Insert Editing .............................................. 52

Audio Dubbing ........................................... 54

NFORMATION ON J TERMINAL 55

PECIAL FEATURES 56

TV Multi-Brand Remote Control .............................. 56

Cable Box Multi-Brand Remote Control ...................57

DBS Receiver Multi-Brand Remote Control..............58

Control Two JVC VCRs ............................................ 59

Child Lock ...............................................................59

ROUBLESHOOTING 60

Power ........................................................ 60

Tape Transport ............................................ 60

Playback ....................................................60

Recording ...................................................61

Timer Recording.......................................... 61

Other Problems .......................................... 62

UESTIONS AND ANSWERS 63

Playback ....................................................63

Recording ...................................................63

Timer Recording.......................................... 63

NDEX 64

List Of Terms............................................... 64

Front View.................................................. 65

Rear View .................................................. 66

Front Display Panel..................................... 66

Remote Control ...........................................67

PECIFICATIONS 68

OR SERVICING (Only in U.S.A.) 69

F W

ARRANTY (Only in U.S.A.) 70

6 EN

INSTALLING YOUR NEW VCR

Basic Connections

Connections

Antenna or Cable

Coaxial Cable

Flat Feeder

AC Power Cord

Back of VCR

AC Outlet

Matching Transformer (not supplied)

Audio/Video Cable (supplied)

75 ohm terminal

NOTES:

●

The VCR channel is the channel on the TV which will display the audio and video signals from the VCR. The VCR's CH3CH4 switch, on the back of the VCR, sets the VCR channel to CH3 or CH4.

●

The CH3–CH4 switch is preset to the CH3 position. Set to CH4 if CH3 is used for broadcasting in your area and set the channel on the TV to correspond to the VCR's CH3– CH4 switch setting.

●

If RF connection to TV is used, when switching from VCR to TV mode and from TV to VCR it may be necessary to issue a CH UP and then CH DOWN on TV to obtain a good quality picture.

●

Even if you are using AV cables to connect your VCR to your TV, you must also connect it using the RF cable. This will ensure that you can record one show while watching another (Z pg. 38).

●

For full identification of the VCR's rear panel, refer to the Index (REAR VIEW Z pg. 66).

ANTENNA IN (Antenna or Cable input)

TV OUT

RF Cable (supplied)

Back of VCR

CH3 CH4

CHECK CONTENTS

Make sure the package contains all of the accessories listed in “SPECIFICATIONS” (Z pg. 68).

SITUATE VCR

Place the VCR on a stable, horizontal surface.

CONNECT VCR TO TV

The connection method you use depends on the type of TV you have.

RF Connection

●

To Connect To A TV With NO AV Input Terminals . . .

a– Disconnect the TV antenna from the TV. b– Connect the TV antenna cable to the ANTENNA

IN jack on the rear of the VCR.

c– Connect the supplied RF cable between the TV

OUT jack on the rear of the VCR and the TV’s antenna terminal. Set TV on CH3 or CH4 corresponding to the CH3 – CH4 switch setting on the back of the VCR.

AV Connection

●

To Connect To A TV With AV Input Terminals . . .

a– Connect the antenna, VCR and TV as shown in

the illustration.

b– Connect an Audio/Video Cable between the AUDIO

OUT and VIDEO OUT jacks on the rear of the VCR and the AV IN jacks on the TV. Set your TV in video input mode or A/V input mode. Refer to the TV Instruction Manual.

S-VIDEO Connection

●

If you have a TV with S-VIDEO input terminals, see "S-VIDEO Connection" on page 7.

CONNECT VCR TO POWER SOURCE

Connect the power plug to an AC outlet.

● The clock and tuner channels will automatically be

set when the antenna is connected and when the AC is first connected to the VCR (Z pg. 8). (If "Auto" or "CH" is displayed on the front display panel before the VCR is powered on, the clock and tuner channels are being set automatically. Wait for the time to be displayed on the front display panel before powering on the VCR.)

FINAL PREPARATION FOR USE

Power on the VCR and select the VCR channel (3 or 4) by setting the switch on the rear of the VCR as shown in the illustration. You can now perform simple playback (Z pg. 25) or simple recording (Z pg. 26).

AC Power Cord

Antenna or Cable

Coaxial Cable

Flat Feeder

Matching Transformer (Not supplied)

EN 7

ANTENNA-IN (Antenna or Cable input)

Back of VCR

AC Outlet

Audio/Video Cable (supplied)

S-VIDEO IN

75 ohm terminal

NOTES:

n Your S-VHS VCR allows you to make high resolution

recordings. For highest quality recordings we recommend that you record in the S-VHS mode (Z pg.39)

n To make the most of the Super VHS picture performance we

recommend that you use the supplied S-VIDEO cable to connect your VCR to a TV with an S-VIDEO input connector.

n To operate the VCR with your TV using the S-VIDEO connec-

tion, set your TV to the AV mode using the TV's remote control. You can also use the TV/VCR button on the VCR's remote control to set your TV to the AV mode. (Z pg. 56)

S-VIDEO OUT

S-Video Cable (supplied)

TV OUT

RF Cable (supplied)

S-VIDEO Connection

CONNECT VCR TO TV

a– Connect both the RF cable and the AV cables to the TV as

explained in step 3 of "Basic Connections" (Z pg. 6).

b– Connect the S-Video cable between the S-VIDEO OUT

jack on the rear of the VCR and the S-VIDEO IN jack on the TV.

8 EN

Plug & Play

Auto Clock Set/Auto Tuner Set

IMPORTANT

● Don’t press any buttons on the VCR or remote while Plug & Play is in progress.

● If you perform Plug & Play successfully, there’s no need to perform the Clock (Z pg. 11) and Tuner (Z pg. 14) procedures. If, however, you want to add or delete channels, refer to “Add Or Delete A Channel” on page 16.

INITIAL SETTINGS

The Plug & Play function sets the clock and tuner channels automatically when power is first connected to the VCR. The antenna cable must be connected for the Plug & Play function.

The time and date can be set automatically from clock setting data that is transmitted by one of the regular TV broadcast channels. We call this TV channel the “Host Channel” and it is a PBS channel in your area.

PLUG & PLAY SETUP

Connect the antenna cable to the VCR (Z pg. 6). Then connect the VCR’s power plug to an AC outlet. Do not

power on the VCR. The clock and tuner channels will be set automatically. If you use a cable box, see "ATTENTION CABLE BOX SUBSCRIBERS" on this page.

NOTES:

● Auto clock set is performed first. The auto clock set function scans all the channels received by your VCR to find the Host Channel and then sets the clock. "Auto" blinks on the front display panel during Auto clock set.

● Auto channel set is performed next. The auto channel set function scans all the channels that are receivable by your VCR. It then automatically assigns each receivable channels to the CH▲▼ buttons. It skips non-receivable channels. During auto channel set the channel numbers are displayed as they are scanned and set.

● When Plug & Play has been completed successfully the correct time is displayed.

● If an incorrect time or "– –:– –" appears on the display panel, see "What To Do If Plug & Play Has Failed" on next page.

During Initial Auto Clock Set

"Auto" blinks.

* If an incorrect time or "– –:– –" appears on the display panel, see "What To Do If Plug & Play Has Failed" on next page.

During Auto Channel Set

The channel numbers are displayed as they are scanned and set.

Plug & Play Completed

The current time (including AM/PM) is displayed.

ATTENTION CABLE BOX SUBSCRIBERS

To perform the Plug & Play procedure . . .

● Connect your cable box to your VCR with the RF cable.

● Select the PBS channel on your cable box before plugging your VCR's power plug into the AC outlet.( If Plug & Play is not

successful you may have to select an alternative PBS channel if another is available in your area.)

● If there is no PBS channel in your area, or if Plug & Play is not successful, perform the Manual Clock Set procedure (Z pg.

13).

● For automatic clock adjustment to take place the VCR's power must be off and the cable box must be set to the PBS channel at clock adjustment times.

● If you perform Plug & Play successfully, D.S.T. will be set to “AUTO”. At the D.S.T. adjustment time (Z pg. 13), your VCR's power must be off and your cable box must be set to the host PBS channel in your area for the D.S.T. adjustment to take place. If the clock is not set correctly, change the D.S.T. setting to “ON” or “OFF. See step 9 of Semi-Auto procedure (Z pg. 13) or step 6 of Manual procedure (Z pg. 13).

EN 9

INFORMATION

● If "AUTO CLOCK SET" or "SEMI-AUTO CLOCK SET" is selected at the Override Auto Clock Set screen on page 12, the clock will be adjusted automatically by the host channel every hour on the hour (except for 11:00 PM, midnight, 1:00 AM and 2:00 AM) by the incoming PBS channel clock setting data. (This automatic clock adjustment can only be performed when the VCR’s power is turned off. The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.) The default setting is "AUTO CLOCK SET".

● If the memory backup fails, because of a power outage or because the AC was removed from the VCR, Plug & Play will be performed when power is restored to the VCR.

What To Do If Plug & Play Has Failed

● If an incorrect time is displayed on the front display panel, you may be receiving the clock setting data of a PBS channel from an adjacent time zone, or an incorrect PBS channel from a cable TV system. In this case, perform the Semi-Auto ( Manual Clock Set (

● If “- -:- -” appears on the display, your antenna cable may not be connected to the VCR, there may not be a Host PBS signal available in your area, or your cable box may not be set to the PBS channel. Ensure that the antenna cable is connected correctly. If you use a cable box ensure that your local PBS channel is selected on your cable box ( SCRIBERS). Then power on and power off the VCR; the Plug & Play function will be automatically reactivated and "Auto" will be displayed on the VCR's front panel. If Plug & Play is not performed but everything is connected and set correctly, perform the Manual Clock Set procedure ( Channels” procedure (

Z pg. 13) procedure. Auto channel set has already taken place and it need not be set again.

Z pg. 8 ATTENTION CABLE BOX SUB-

Z pg. 13). Auto channel set has not yet taken place, so please also perform the “Set Receivable

Z pg. 14).

Z pg. 12) or

10 EN

POWER

Language

INITIAL SETTINGS (cont.)

This VCR offers you the choice to view on-screen messages in English, Spanish or French (not including messages superimposed on the TV picture). Select the desired language using this procedure. The default setting is "ENGLISH".

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

POWER

456

TURN ON THE VCR

Press POWER.

ACCESS ON-SCREEN MENU

Press MENU as many times as necessary.

ACCESS CUSTOM SET SCREEN

At the Main Menu screen, move the highlight bar

(arrow) to “CUSTOM SET” by pressing CH5∞ or

SHUTTLE PLUS%ﬁ, then press OK.

ACCESS LANGUAGE SELECT SCREEN

The messages are preset to appear in English. If you want

to see them in Spanish or French, move the highlight bar (arrow) to “LANGUAGE SELECT” by pressing CH5∞ or SHUTTLE PLUS%ﬁ, then press OK.

MAIN MENU

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

VIDEO CALIBRATION VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

CUSTOM SET

OVERRIDE

AUTO CLOCK SET

=LANGUAGE SELECT

VCR PLUS+ SET-UP DBS RECEIVER OUTPUT DBS RECEIVER BRAND SET JLIP ID NO. SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

1¡

4¢

SHUTTLE PLUS

SELECT LANGUAGE

At the Language Select screen, move the highlight

bar (arrow) to the desired language by pressing

CH5∞ or SHUTTLE PLUS%ﬁ, then press MENU as many times as

necessary to return to the normal screen.

LANGUAGE SELECT

=ENGLISH

ESPAÑOL FRANCAIS

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

Clock

POWER

EN 11

Perform clock setting only if the clock has not been set correctly by the Plug & Play function. Access the Override Auto Clock Set screen to choose the Auto, Semi-Auto or Manual clock setting procedure. Each procedure starts from step 5. *Auto need only be selected if Semi-Auto or Manual had previously been selected.

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

POWER

456

1¡

Preparation

TURN ON THE VCR

Press POWER.

ACCESS ON-SCREEN MENU

Press MENU as many times as necessary.

ACCESS CUSTOM SET SCREEN

At the Main Menu screen, move the highlight bar

(arrow) to “CUSTOM SET” by pressing CH5∞ or SHUTTLE PLUS%ﬁ, then press OK.

ACCESS CLOCK SET MODE SELECT SCREEN

Move the highlight bar (arrow) at the Custom Set

screen to “OVERRIDE AUTO CLOCK SET” by pressing CH5∞ or

SHUTTLE PLUS%ﬁ, then press OK.

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

VIDEO CALIBRATION VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

=OVERRIDE

AUTO CLOCK SET

LANGUAGE SELECT VCR PLUS+ SET-UP DBS RECEIVER OUTPUT DBS RECEIVER BRAND SET JLIP ID NO. SET

PRESS (5,∞), THEN (OK)

PRESS (MENU) TO END

MAIN MENU

CUSTOM SET

4¢

SHUTTLE PLUS

12 EN

SHUTTLE PLUS

456

1¡

4¢

INITIAL SETTINGS (cont.)

Semi-Auto

SELECT MODE

At the Override Auto Clock Set screen, move the

highlight bar (arrow) to “SEMI-AUTO CLOCK SET” by pressing CH▲▼ or

SHUTTLE PLUS%ﬁ, then press OK.

OVERRIDE AUTO CLOCK SET

AUTO CLOCK SET

=SEMI–AUTO CLOCK SET

MANUAL CLOCK SET

PRESS (5,∞), THEN (OK)

PRESS (MENU) TO END

ACCESS SELECT SCREENS

At the Semi-Auto Clock Set screen, move the highlight

bar (arrow) to the desired mode by pressing CH▲▼ or SHUTTLE PLUS%ﬁ, then press OK.

To select the Host Channel — step 7 To select the Time Zone — step 8 To select the D.S.T. mode — step 9

NOTE:

The time that has been set previously by the Plug & Play function will be erased when any of the three settings mentioned above is changed.

SEMI–AUTO CLOCK SET

=HOST CHANNEL SELECT

TIME ZONE SELECT D.S.T. SELECT

PRESS (5,∞), THEN (OK)

PRESS (MENU) TO END

SELECT HOST CHANNEL

You can either select "AUTO", or enter a PBS

channel number. For automatic selection, press MENU if "AUTO" is highlighted on the Host Channel Select screen. To manually select "AUTO" or the PBS channel, press CH▲▼ or SHUTTLE PLUS%ﬁ to cycle through "AUTO" or the channel numbers (hold button down to speed through numbers) and stop when the desired number appears. Press MENU and the Semi-Auto Clock Set screen reappears.

HOST CHANNEL SELECT

PRESS (5,∞) TO SELECT

PRESS (MENU) TO END

(CATV)

CH AUTO

NOTES:

●

For cable box users: Select "AUTO" or the channel on your VCR that receives the cable box channels, and set the cable box to the PBS channel.

●

There are some PBS channels that do not transmit clock setting data.

EN 13

SELECT TIME ZONE

You can select the zone automatically or manually

by pressing CH▲▼ or SHUTTLE PLUS%ﬁ. If an

incorrect time is displayed you may be receiving the clock setting data of a PBS channel from an adjacent time zone or from an incorrect PBS channel from a cable TV system. If you selected "AUTO" in step 7 select "MANUAL" and select the correct time zone manually.

● If you selected "AUTO", press MENU to return to the

Semi-Auto Clock Set screen.

● If you selected

"MANUAL", press OK and the screen to the right appears. Move the highlight bar (arrow) to your choice by pressing

CH▲▼ or SHUTTLE PLUS%ﬁ, then press MENU twice to return to

the Semi-Auto Clock Set screen.

TIME ZONE SELECT

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

TIME ZONE SELECT

=ATLANTIC

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

SELECT D.S.T. MODE

You have three choices:

a–Select “AUTO” and the

adjustment to your VCR’s clock will be made according to the incoming signal from the host channel. b–Select “ON” and the adjustment will be made based on the clock itself. c–Select “OFF” if Daylight Saving Time doesn’t apply to you. Move the highlight bar (arrow) to your choice by pressing CH MENU and the Semi-Auto Clock Set screen reappears.

or SHUTTLE PLUS

∞

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

=AUTO

MANUAL

EASTERN CENTRAL MOUNTAIN PACIFIC ALASKA HAWAII

D.S.T. SELECT

=AUTO

ON OFF

, then press

ﬁ

Manual

SELECT MODE

At the Override Auto Clock Set screen (Z pg. 12), move the highlight bar (arrow) to “MANUAL CLOCK SET” by

pressing CH▲▼ or SHUTTLE PLUS%ﬁ, then press OK.

SET DATE, TIME AND D.S.T.

The Manual Clock Set screen is displayed and the

month digit begins blinking. Press the appropriate NUMBER keys to set the date and time (if only 1 digit, press "0" first). Press CH▲▼ or SHUTTLE PLUS%ﬁ to set AM/PM and D.S.T. (Daylight Saving Time). Press OK after AM/ PM and D.S.T. settings. Set D.S.T. to "ON" to set the D.S.T. according to the VCR's clock or to "OFF" if D.S.T. doesn't apply to you.

When you’re finished with this set-up procedure, press MENU to start the clock.

NOTES:

●

CH▲▼ and SHUTTLE PLUS

perform all operations. (In this case, press OK after each setting.)

●

At the Manual Clock Set screen, the setting that can be set blinks. When setting of a highlighted item is completed, the highlight bar moves down by 1 line to the next item.

MANUAL CLOCK SET

DATE 1/ 1/97 WED

TIME – –:– – AM D.S.T. ON

PRESS NUMBER KEY (O–9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

can be used to

ﬁ

MAKE CORRECTIONS

To change any of the settings, press OK or SHUTTLE

ﬁ

PLUS until the item you want to change blinks,

then set as in step 6.

Auto

IMPORTANT

Turn the VCR off after performing the Semi-Auto Clock Set procedure. "Auto" will appear on the front display panel when the clock is being set. The current time will appear automatically when the clock is set.

SELECT MODE

At the Override Auto Clock Set screen, move the highlight bar (arrow) to "AUTO CLOCK SET" by

pressing CH▲▼ or SHUTTLE PLUS%ﬁ, then power off the VCR. Do not power it on again until the clock has been adjusted. After the clock is set it will be automatically adjusted on the hour except at 11:00 PM, midnight, 1:00 AM and 2:00 AM. (The clock will be adjusted on the hour based on the time displayed on the VCR, not on the actual real time.)

**AUTO DAYLIGHT SAVING TIME

This function enables automatic adjustment of the VCR’s clock at the start and end of Daylight Saving Time. With Auto DST activated, . . . . . . on the first Sunday of April at 2:00 AM, the clock is

adjusted to 3:00 AM.

. . . on the last Sunday of October at 2:00 AM, the clock is

adjusted to 1:00 AM.

14 EN

POWER

INITIAL SETTINGS (cont.)

Set Receivable Channels

Tuner

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

POWER

SHUTTLE PLUS

456

1¡

4¢

TURN ON THE VCR

Press POWER.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

ACCESS TUNER SET SCREEN

Move the highlight bar (arrow) to "TUNER SET" by

pressing CH5∞ or SHUTTLE PLUS%ﬁ, then press OK.

PERFORM AUTO CHANNEL SET

Move the highlight bar (arrow) to "AUTO

CHANNEL SET" by pressing CH5∞ or SHUTTLE PLUS%ﬁ, then press OK.

● Receivable channels in your area are automatically assigned to the CH5∞ buttons, and non-receivable channels are skipped.

NOTES:

●

At the end of Auto Channel Set, “SCAN COMPLETED” appears on screen.

●

If the scan was unsuccessful, “SCAN COMPLETED– NO SIGNAL” appears on screen. Check the connections and start again.

PROGRAM SET FUNCTION SET

=TUNER SET

CUSTOM SET VIDEO CALIBRATION VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

BAND AFC

=AUTO CHANNEL SET

MANUAL CHANNEL SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

AUTO CHANNEL SET

PRESS (MENU) TO END

MAIN MENU

TUNER SET

SCANNING...

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

EN 15

INFORMATION

The VCR detects the band (TV or CATV) and selects the correct band automatically during Auto Channel Set. If necessary, you can check the setting at the Band screen after Auto Channel Set has set the channels.

● At the Tuner Set screen, move the highlight bar (arrow) to

"BAND" by pressing CH5∞ or SHUTTLE PLUS%ﬁ, then press OK.

TUNER SET

=BAND

AFC AUTO CHANNEL SET MANUAL CHANNEL SET

BAND

=CATV

456

1¡

4¢

SHUTTLE PLUS

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

● Press MENU as many times as necessary to return to the

normal screen.

16 EN

ADD

CH.SKIP

NUMBER

SHUTTLE PLUS

456

1¡

4¢

INITIAL SETTINGS (cont.)

Add Or Delete A Channel

ACCESS TUNER SET SCREEN

Access by performing steps 2 and 3 of the Tuner procedure on page 14.

● To add a channel, go to step 2.

● To delete a channel, skip to step 4.

ACCESS AFC SCREEN

Move the highlight bar (arrow) to "AFC" by pressing

CH5∞ or SHUTTLE PLUS%ﬁ, then press OK.

MAKE SELECTION

Move the highlight bar (arrow) to "SPCL" by

pressing CH5∞ or SHUTTLE PLUS%ﬁ, then

press MENU to return to the Tuner Set screen.

● AFC set to SPCL (special) is necessary for tuning on certain CATV systems.

ACCESS MANUAL CHANNEL SET SCREEN

Move the highlight bar (arrow) to "MANUAL CHANNEL SET" by pressing CH5∞ or SHUTTLE PLUS%ﬁ, then

press OK.

STORE OR SKIP DESIRED CHANNEL

Input the channel number using the NUMBER keys or

by pressing CH5∞ or SHUTTLE PLUS%ﬁ, then press ADD to add or CH.SKIP to delete. Repeat

for each channel you want to store or skip.

AFC

NORM

=SPCL

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

MANUAL CHANNEL SET

(CATV)

CH 125 ADD

SELECT CH NO. AND PRESS (ADD/SKIP) PRESS (MENU) TO END

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

Cable Box Control

Suggested Location

Place the cable box on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

Attention:

The Controller can also control a DBS receiver. If both a cable box and a DBS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DBS receiver.

Cable box

Your VCR

Cable box

Controller (suggested locations)

EN 17

This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using VCR Plus+ (Z pg. 42) or On-Screen Timer Programming (Z pg. 44).

Situate And Connect Controller

SITUATE CONTROLLER

Place the Controller so that the path between its transmitter and the cable box’s remote sensor is

unobstructed.

ATTACH CONTROLLER

Fasten securely using the supplied adhesive strip.

CONNECT CABLE BOX TO VCR

The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR; select the correct external input mode as described in step 4, 5, 9, 10, 14 on page 50 & 51. Set the VCR to channel "AU" to use the cable box.

If your cable box doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the cable box to the ANTENNA IN connector on the rear of your VCR. Set the VCR tuner to the same channel as the cable box RF output (see page 18 also).

Controller

Your VCR

Transmitter

Connected to ANTENNA IN

CABLE

BOX

Connected to VIDEO/ AUDIO IN

NOTE:

When connecting your cable box refer to its instruction manual.

CONNECT CONTROLLER TO VCR

Connect to the CABLE BOX connector on your VCR.

About Your Cable Box

This VCR has two separate methods to control your Cable Box.

●

The VCR's Wireless Remote Control Unit can control your Cable Box. This eliminates the need for a separate Cable Box Remote Control Unit.

●

The VCR's Controller can also control your Cable Box. This allows the VCR to change your Cable Box's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 57. To set up the Controller go to page 18.

18 EN

POWER

INITIAL SETTINGS (cont.)

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

POWER

NUMBER

456

1¡

ACCESS CUSTOM SET SCREEN

Press CH5∞ or SHUTTLE PLUS%ﬁ to move the

highlight bar (arrow) to “CUSTOM SET”, then press OK.

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

VIDEO CALIBRATION VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ACCESS VCR PLUS+ SET-UP SCREEN

Press CH5∞ or SHUTTLE PLUS%ﬁ to move the

highlight bar (arrow) to “VCR PLUS+ SET-UP”, then press OK.

OVERRIDE

AUTO CLOCK SET

LANGUAGE SELECT

=VCR PLUS+ SET-UP

DBS RECEIVER OUTPUT DBS RECEIVER BRAND SET JLIP ID NO. SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ACCESS CABLE BOX OUTPUT SCREEN

Press CH PLUS

highlight bar (arrow) to

“CABLE BOX OUTPUT”, then press OK.

∞

to move the

ﬁ

or SHUTTLE

VCR PLUS+ SET-UP

GUIDE CHANNEL SET GUIDE CHANNEL MAP

=CABLE BOX OUTPUT

CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

MAIN MENU

CUSTOM SET

4¢

Set Cable Box Output Channel

TURN ON THE VCR

Press POWER.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

SHUTTLE PLUS

SELECT CABLE BOX OUTPUT CHANNEL

Your selection depends on how your cable box is

connected to your VCR.

If your cable box is connected to your VCR using an RF connection . . .

. . . press CH5∞ or SHUTTLE PLUS%ﬁ to

move the highlight bar (arrow) to the channel number representing the cable box’s output (2–6).

If your cable box is connected to your VCR’s AUDIO/ VIDEO IN connectors . . .

. . . press CH5∞ or SHUTTLE PLUS%ﬁ to move the highlight bar (arrow) to “ON LINE”.

CABLE BOX OUTPUT

PRESS (5,∞) TO SELECT PRESS (MENU) TO END

RETURN TO VCR PLUS+ SET-UP SCREEN

Press MENU.

=OFF

ON CH2 ON CH3 ON CH4 ON CH5 ON CH6 ON LINE

EN 19

Set Cable Box Brand

TURN ON CABLE BOX

Select a channel other than channel 9 on your Cable Box.

ACCESS CABLE BOX BRAND SET SCREEN

At the VCR Plus+ Set-Up screen, press CH5∞ or

SHUTTLE PLUS%ﬁ to

move the highlight bar (arrow) to “CABLE BOX BRAND SET”, then press

OK.

VCR PLUS+ SET-UP

GUIDE CHANNEL SET GUIDE CHANNEL MAP CABLE BOX OUTPUT

=CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ENTER CABLE BOX BRAND

Press the appropriate

NUMBER keys to enter the

Cable Box Code from the CABLE BOX BRAND LIST to the right, then press OK.

● If the cable box’s channel changes to 9, setting is complete.

● If there are more than one code number listed for your brand of cable box, repeat step 3 until the cable box’s channel changes to 9.

● If the channel does not change after going through all the code numbers listed for your model of cable box, then try all the other numbers between 1 and 69.

CABLE BOX BRAND SET

PRESS NUMBER KEY (0-9)

PRESS (MENU) TO END

THEN (OK)

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

You can now set up the VCR Plus+ feature (

NOTES:

●

Although the supplied Controller is compatible with many different cable box brands, it is possible that it will not work with your cable box.

●

If your cable box doesn’t respond to any code between 1 and 69, you can’t use the Controller to change cable box channels. In this case, make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording. Please contact your cable company about the possibility of exchanging your current cable box with one that is compatible with your VCR.

●

The VCR can only change the cable box channel through the Controller during timer recording.

●

If your cable box is one that can’t be operated with a remote control (because it has no remote sensor), you can’t use the Controller to change its channels. Make sure to leave the cable box turned on and tuned to the proper channel before the scheduled start of timer recording.

●

For customers in U.S.A.: If you are unable to set the Controller, please contact JVC toll free at 1-800-252-5722.

Z pg. 20).

CABLE BOX BRAND LIST

BRAND CODE

ARCHER 49, 52, 53, 54 CABLEVIEW 49, 53 CITIZEN 49, 53 CURTIS 9, 10, 62, 63 DIAMOND 52, 53, 54 EAGLE 30, 31, 32, 33, 34, 35, 36, 37 EASTERN 51 GC BRAND 49, 53 GEMINI 8, 56 GENERAL ELECTRIC 67 GENERAL INSTRUMENTS 1, 2, 3, 4, 5, 6, 7,8 HAMLIN 15, 16, 17,18 JERROLD 1, 2, 3, 4, 5, 6, 7, 8 MACOM, HITACHI 57, 58, 59 MAGNAVOX 30, 31, 32, 33, 34, 35, 43 MOVIETIME 44, 45, 46 NSC 44, 45, 46 OAK 19, 20, 21, 30, 47, 48 PANASONIC 24, 25, 26 PHILIPS 30, 31, 32, 33, 42 PIONEER 13, 14 PULSER 49, 53 RCA 24, 25, 26 REGAL 15, 16, 17, 18, 33 REGENCY 51 SAMSUNG 8, 13, 49, 50 SCIENTIFIC ATLANTA 9, 10, 62, 63 SIGMA 19, 20, 21 SL MARX 8, 13, 49, 50 SPRUCER 24, 25, 26 STARGATE 8, 13, 49, 50 SYLVANIA 29 TEKNIKA 68, 69 TELECAPTION 27 TELEVIEW 8, 13, 49, 50 TEXSCAN 28, 29 TOCOM 22, 23, 64, 65, 66 UNIKA 52, 53, 54 UNIVERSAL 38, 39, 40, 41 VIDEOWAY 11, 12, 60, 61 VIDEO TECH 55 VIDTER 55 VIEWSTAR 30, 31, 32, 33, 34, 35, 36, 37 ZENITH 11, 12, 60, 61

20 EN

POWER

VCR Plus+ Setup

Turn on the TV and select the VCR channel 3 or 4 (or AV mode).

456

1¡

POWER

NUMBER

INITIAL SETTINGS (cont.)

The VCR Plus+ timer programming system eliminates the need to input channel, date, start and stop time data when setting the timer record function. Simply key in the PlusCode number for the TV program you wish to record and the VCR's timer will be automatically programmed. (The PlusCodes are the numbers next to the programs in most TV listings.)

TV and cable stations can be received on different channel numbers depending on the area where they are received. Therefore to ensure that VCR Plus+Timer Recording operates correctly it may be necessary to set the VCR Plus+ "Guide Channel Set " for certain stations. Please read the following information carefully to find out which tasks you need to perform.

Before VCR Plus+ setup you must have performed the following procedures:

● Plug & Play (

Clock setting (Z pg. 11) and Tuner setting (Z pg. 14)

● Cable box setting if you receive your TV channels through a cable box (Z pg. 17)

VCR Plus+ Guide Channel Matching

VCR Plus+ assigns a VCR Plus+ "Guide Channel" to broadcast and cable TV channels. These Guide Channel numbers are also called the VCR Plus+ Channel Codes. Most TV listings have a section, usually a chart, indicating the "Guide Channel" numbers assigned to each station. For accurate VCR Plus+ Programming the VCR Plus+ Guide Channel number for each station should match the channel number on which it is received in your area.

If the numbers match, go directly to “VCR Plus+ Timer Programming” (Z pg. 42).

If the numbers are different, and you want to be able to timer record programs from those stations, you have to inform the VCR of the mismatch. Go to step 1. If you will not want to timer record from those stations, you can go directly to “VCR Plus+ Timer Programming” (Z pg. 42).

NOTES:

● In many instances the VCR Plus+ Guide Channel numbers for cable and broadcast TV stations DO NOT match the channel number on which it is received by your VCR or cable box. Check your TV listing, or contact your cable supplier for details.

● If the VCR Plus+ Guide Channel numbers do not match, the wrong VCR/CABLE CH number will be displayed on the Program Screen when you enter the PlusCode for VCR Plus+ Programming. If this occurs set the correct VCR Plus+ Guide Channel to match this number.

● Many broadcast TV stations can be viewed on cable. Check your TV listing, or contact your cable supplier for details.

Z pg. 8)

4¢

SHUTTLE PLUS

TURN ON THE VCR

Press POWER.

ACCESS MAIN MENU SCREEN

Press MENU as many times as necessary.

EN 21

ACCESS CUSTOM SET SCREEN

Press CH5∞ or SHUTTLE PLUS%ﬁ to move the

highlight bar (arrow) to “CUSTOM SET”, then press OK.

PROGRAM SET FUNCTION SET TUNER SET

=CUSTOM SET

VIDEO CALIBRATION VIDEO STABILIZER PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ACCESS VCR PLUS+ SET-UP SCREEN

Press CH5∞ or SHUTTLE PLUS%ﬁ to move the

highlight bar (arrow) to “VCR PLUS+ SET-UP”, then press OK.

OVERRIDE

AUTO CLOCK SET

LANGUAGE SELECT

=VCR PLUS+ SET-UP

DBS RECEIVER OUTPUT DBS RECEIVER BRAND SET JLIP ID NO. SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

ACCESS GUIDE CHANNEL SET SCREEN

Press CH PLUS

highlight bar (arrow) to

“GUIDE CHANNEL SET”, then press OK.

∞

to move the

ﬁ

or SHUTTLE

VCR PLUS+ SET-UP

=GUIDE CHANNEL SET

GUIDE CHANNEL MAP CABLE BOX OUTPUT CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

INPUT GUIDE CHANNEL NUMBER

Press CH5∞, SHUTTLE PLUS%ﬁ or the

appropriate NUMBER keys to input the VCR Plus+ Guide Channel number as shown in the TV listing. Then press OK.

● If you receive your channels with a cable box and if you have properly set your Controller, “CABLE CH” appears in place of “VCR CH”. If not, refer to pages 17–18 and re-perform the procedure.

(Ex.) When inputting the Guide Channel number 6 for WNJU(Ind.)

GUIDE CHANNEL SET

GUIDE CH : 6

VCR CH : 6

PRESS NUMBER KEY (0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

MAIN MENU

CUSTOM SET

INPUT RECEIVING CHANNEL NUMBER

Press CH5∞, SHUTTLE PLUS%ﬁ or the

appropriate NUMBER keys to input the number of the channel on which the Guide Channel’s broadcasts are received. Then press OK.

● If there is more than one

mismatch, repeat steps 6 and 7 for each instance.

(Ex.) If WNJU(Ind.) is received on channel 47

GUIDE CHANNEL SET

GUIDE CH : 6

VCR CH : 47

PRESS NUMBER KEY (0-9)

OR (5,∞), THEN (OK)

PRESS (MENU) TO END

RETURN TO VCR PLUS+ SET-UP SCREEN

Press MENU.

CHECK INPUT DATA

Press CH5∞ or SHUTTLE PLUS%ﬁ to move the

highlight bar (arrow) to “GUIDE CHANNEL MAP”, then press OK.

● The Guide Channel and VCR or cable box channel numbers you input appear on the screen in ascending order. Check to ensure you’ve entered them correctly.

● If you entered more than 10 sets of numbers, press OK to see the next set of numbers.

● Guide Channel Map contains only the Guide Channels and VCR or CABLE channels that you entered.

VCR PLUS+ SET-UP

GUIDE CHANNEL SET

=GUIDE CHANNEL MAP

CABLE BOX OUTPUT CABLE BOX BRAND SET

PRESS (5,∞), THEN (OK) PRESS (MENU) TO END

GUIDE CHANNEL MAP

GUIDE: VCR GUIDE: VCR

6 : 47 10 : 55 12 : 41 15 : 38 33 : 28 67 : 49

PRESS (OK) TO NEXT PRESS (MENU) TO END

RETURN TO NORMAL SCREEN

Press MENU as many times as necessary.

You can now use VCR Plus+ for quick and simple timer programming (Z pg. 42).

22 EN

DBS Receiver Control

Suggested Location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver's remote sensor.

Attention:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the controller so its signal reaches the remote control sensors of both the DBS receiver and cable box.

DBS receiver

INITIAL SETTINGS (cont.)

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) Receiver. The Controller allows the VCR to automatically switch the DBS Receiver's channels during timer recording.

NOTES:

●

The VCR can automatically change the DBS Receiver channels using the controller when the VCR has been programmed using On-Screen Timer Programming (Z pg. 44). Because satellite programming does not use PlusCode; the Controller can not change the DBS Receiver channels during VCR Plus+ Timer Recording.

●

If a cable box is also used it is recommended that you connect the DBS receiver to your VCR's A/V inputs and the cable box to your VCR's antenna input.

Situate And Connect Controller

SITUATE CONTROLLER

Place the Controller so that the path between its transmitter and the DBS receiver's remote sensor is

unobstructed.

ATTACH CONTROLLER

Fasten securely using the supplied adhesive strips.

Your VCR

Controller

DBS receiver

Transmitter

Connected to ANTENNA IN

CABLE

BOX

Controller (suggested locations)

Connected to VIDEO/ AUDIO IN

About Your DBS Receiver

This VCR has two separate methods to control your DBS Receiver.

●

The VCR's Wireless Remote Control Unit can control your DBS Receiver. This eliminates the need for a separate DBS Receiver Remote Control Unit.

●

The VCR's Controller can also control your DBS Receiver. This allows the VCR to change your DBS receiver's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 58. To set up the Controller go to page 23.

CONNECT DBS RECEIVER TO VCR

The connection method depends on the type of DBS receiver you have.

If your DBS receiver has AUDIO and VIDEO OUT connectors . . .

If your DBS receiver doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the DBS receiver to the ANTENNA IN connector on the rear of your VCR. Set the VCR's tuner to the same channel as the DBS receiver's RF output. (See page 23 also.)

NOTE:

When connecting your DBS receiver refer to its instruction manual.

CONNECT CONTROLLER TO VCR

Connect to the CABLE BOX connector on your VCR.

+ 50 hidden pages