JVC HR-J4010UM User Manual
VIDEO CASSETTE RECORDER
HR-J4010UM
INSTRUCTIONS
LPT0793-001A
COPYRIGHT © 2003 VICTOR COMPANY OF JAPAN, LTD.
UM
Printed in Thailand
J4F12701A
03/02
0203-AH-OR-OR
K
Dear Customer,
Thank you for purchasing the JVC VHS video cassette recorder.
Before use, please read the safety information and precautions to
ensure safe use of your new VCR.
CAUTIONS
WARNING: DANGEROUS VOLTAGE INSIDE
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
The POWER /l button does not completely shut off mains
power from the unit, but switches operating current on and off.
“ ” shows electrical power standby and “ l ” shows ON.
This unit is produced to comply with Standard IEC 60065.
POWER SYSTEM:
This set operates on voltage of AC 110 – 220V~, 50/60 Hz with
automatic switching.
Use the conversion plug (provided) depending on the type of
your AC WALL outlet.
CAUTION
■ When you are not using the VCR for a long period of time, it is
recommended that you disconnect the power cord from the
AC outlet.
■ Dangerous voltage inside. Refer internal servicing to qualified
service personnel. To prevent electric shock or fire hazard,
remove the power cord from the AC outlet prior to
connecting or disconnecting any signal lead or aerial.
■ Changes or modifications not approved by JVC could void
user’s authority to operate the equipment.
• Cassettes marked “VHS” (or “S-VHS”) can be used with this video
cassette recorder. However, S-VHS recording is not possible with
this model.
• This model is equipped with SQPB (S-VHS QUASI PLAYBACK)
that makes it possible to play back S-VHS recordings with
regular VHS resolution.
• HQ VHS is compatible with existing VHS equipment.
The rating plate and safety caution are on the rear of the unit.
IMPORTANT:
It may be unlawful to record or play back copyrighted material
without the consent of the copyright owner.
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in damage
to the VCR, Remote or video cassette.
1. DO NOT place the VCR ...
... in an environment prone to extreme temperatures or humidity.
... in direct sunlight.
... in a dusty environment.
... in an environment where strong magnetic fields are generated.
... on a surface that is unstable or subject to vibration.
2. DO NOT block the VCR’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the VCR or Remote.
4. DO NOT place anything which might spill on top of the VCR or
Remote.
(If water or liquid is allowed to enter this equipment, fire or electric
shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with water.
Also DO NOT place any containers filled with water or liquids
(such as cosmetics or medicines, flower vases, potted plants, cups,
etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted candles,
on the apparatus.
8. AVOID violent shocks to the VCR during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the VCR when you move it
from a cold place to a warm place, or under extremely humid
conditions—just as water droplets form on the surface of a glass
filled with cold liquid. Moisture condensation on the head drum will
cause damage to the tape. In conditions where condensation may
occur, keep the VCR’s power turned on for a few hours to let the
moisture dry.
How to use the Remote
Before use, insert two AAA size batteries into the Remote with the
polarity ( and ) matched correctly as indicated on the battery
compartment or on the lid.
● Point the Remote toward the remote sensor on the target
component.
●
The maximum operating distance of the remote control is about 5 m.
NOTE:
If the Remote does not work properly, remove its batteries, wait for
a few seconds, replace the batteries and then try again.
Video heads cleaning
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity.
● in a dusty environment
● flaw, dirt or mold on video tapes
● continuous usage for a long time
Use a dry cleaning cassette — TCL-2 — when:
● Rough, poor picture appears while a tape is played back.
● The picture is unclear or no picture appears.
Buttons, Connectors and Indicators
Front Panel
Rear Panel
VIDEO
AUDIO
VIDEO/AUDIO input
connectors
AC power cord
POWER
POWER
Cassette loading slot
TV/VCR TIMER REC POWER
TV/VCR indicator
TIMER indicator
POWER indicator
REC indicator
CH–/+
CH
Remote sensor
REC
STOP/EJECT
REC
STOP/EJECT
UHF/VHF IN (ANT)
PLAY
PLAY
REW FF
REW FF
OUT
AUDIO/VIDEO OUT
3/4 CHANNEL
SELECTTOR SWITCH
UHF/VHF
IN(ANT)
VIDEO
OUT(TV)
AUDIO
CH
34
UHF/VHF OUT (TV)
– Buttons, Connectors and Indicators –
Remote
POWER
POWER
123
Number keys
AUX
REC
REW
STOP
MENU
SET–/+
TV/VCR
TV POWER
INPUT
TV VOL–/+
This Remote transmit A code
signals only; it is not applicable
to B code signals.
456
7089
–
REC
PLAY
REW FF
MENU
STOP
–
SET
TV/VCR TIMER
SP/EP DISPLAY
–
TV POWER
–
INPUT
TV CH
TV VOL
Connections and VCR channel Setting
Check contents
1
Make sure the package contains all of the accessories listed
CH–/+
+
CH(AUX)
PAUSE
PA US E
PLAY
FF
ENTER
+
CANCEL
C.RESET
ENTER
TIMER
CANCEL
C.RESET
SP/EP
+
+
DISPLAY
TV CH–/+
in “Specifications”.
Situate VCR
2
Place the VCR on a stable, horizontal surface.
Connect VCR to TV
3
Antenna or cable
Coaxial cable
Flat feeder
Matching transformer
(not supplied)
AC power cord
Back of VCR
AC outlet
OUT
UHF/VHF
OUT
IN(ANT)
VIDEO
L
AUDIO
R
34
OUT(TV)
VIDEO
AUDIO
CH
UHF/VHF
IN(ANT)
OUT(TV)
On-screen display
If you press DISPLAY on the Remote, you can see the current VCR
status on the TV screen. Press DISPLAY again to exit on-screen
display.
The indications are not recorded even if the VCR is in the recording
mode.
WHILE WATCHING TV
DAY AND CLOCK TIME
WHILE OPERATING A TAPE
AUTO TRACKING
AUTO TR.
CH 1258 : 30 AM THU
00 : 00 : 00 SP
CHANNEL
TAPE
SPEED
REAL TIME COUNTER
OPERATING MODE
CH 1258 : 30 AM THU
AUTO REPEAT
00 : 00 : 00 SP
TAPE IN
To audio/video input connectors
Audio/video cable
(not supplied)
TV
To 75 Ω terminal
RF cable
(supplied)
RF Connection
1
Disconnect the TV antenna from the TV.
2
Connect the TV antenna cable to the UHF/VHF IN
terminal on the rear of the VCR.
3
Connect the supplied RF cable between the UHF/VHF
OUT terminal on the rear of the VCR and the TV’s
antenna input terminal.
AV Connection
(improves picture quality during tape playback.)
If your TV is equipped with audio/video input connectors
1
Connect the antenna, VCR and TV as shown in the
illustration.
2
Connect an audio/video cable between the AUDIO/
VIDEO OUT connectors on the rear of the VCR and the
audio/video input connectors on the TV.
• Even if you are using audio/video cables to connect your
VCR to your TV, you must also connect it using the RF
cable. This will ensure that you can record one show while
watching another.
Loading...