JVC GY HM600E, HM600U Instruction Manual

Thank you for purchasing this JVC product. Before operating this unit, please read the instructions carefully to ensure the best possible performance.

In this manual, each model number is described without the last letter (U/E) which means the shipping destination. (U: for USA and Canada, E: for Europe) Only “U” models (GY-HM600U) have been evaluated by UL.

Please read the following before getting started:

For Customer Use:

Model No. GY-HM600U Serial No.

Enter below the Serial No. which is located on the body. Retain this information for future reference.

HD MEMORY CARD CAMERA RECORDER

GY-HM600U/GY-HM600E

INSTRUCTIONS

The specifications and appearance of this product are subject to changes for further improvement without prior notice. Please check the latest version of the INSTRUCTIONS from the following Mobile User Guide, or download the PDF from the URL below.

Mobile User Guide

When you are outside, you can refer to the instructions from your Android phone or iPhone.

http://manual3.jvckenwood.com/pro/mobile/global/

You can view the Mobile User Guide using the browser on your Android phone or iPhone.

Ver. 4.00

LST1424-001C

Read these instructions.

Keep these instructions.

IMPORTANT SAFEGUARDS

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

These are general IMPORTANT SAFEGUARDS and certain items may not apply to all appliances.

Heed all warnings.

FOR USA

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10.

Only use attachments/accessories specified by the manufacturer.

11.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

12.

Unplug this apparatus during lightning storms or when unused for long periods of time.

13.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

INFORMATION (FOR CANADA) RENSEIGNEMENT (POUR CANADA)

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Introduction

Safety Precautions

CAUTION

FOR USA AND CANADA

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Introduction

POUR CANADA

RISQUE

D’ELECTROCUTION

NE PAS OUVRIR

CAUTION:

The mains plug shall remain readily operable.

 Remove the mains plug immediately if

the camera functions abnormally.

WARNING:

The battery pack, the camera with battery installed, and the remote control with battery installed should not be exposed to excessive heat such as direct sunlight, fire or the like.

ATTENTION:

POUR EVITER TOUT RISQUE D’ELECTROCUTION NE PAS OUVRIR LE BOITER. AUCUNE PIECE INTERIEURE N’EST A REGLER PAR L’UTILISATEUR. SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME.

ATTENTION

Le symbole de l’éclair à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’une “tension dangereuse” non isolée dans le boîtier du produit. Cette tension est suffisante pour provoquer l’électrocution de personnes.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’opérations d’entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d’instructions.

Ces symboles ne sont utilisés qu’aux Etats-Unis.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

AVERTISSEMENT : POUR EVITER LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER L’APPAREIL A LA PLUIE NI A L’HUMIDITE.

NOTES:

 The rating plate and safety caution are

on the bottom and/or the back of the main unit.

 The serial number plate is on the

bottom of the unit.

 The rating information and safety

caution of the AC adapter are on its upper and lower sides.

REMARQUES :

 La plaque d’identification et

l’avertissement de sécurité se trouvent sous l’appareil et/ou au dos.

 La plaque du numéro de série est

située sur la partie inférieure de l’appareil.

 Les informations d’identification et

l’avertissement de sécurité de l’adaptateur secteur sont situés sur ses côtés supérieur et inférieur.

Caution on Replaceable lithium battery

The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C (212°F) or incinerate. Replace battery with Panasonic, Sanyo, Sony or Maxell CR2025. Danger of explosion or risk of fire if the battery is incorrectly replaced.

 Dispose of used battery promptly.  Keep away from children.  Do not disassemble and do not dispose

of in fire.

Introduction

When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear). Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.) No naked flame sources, such as lighted candles, should be placed on the apparatus. When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Do not point the lens directly into the sun. This can cause eye injuries, as well as lead to the malfunctioning of internal circuitry. There is also a risk of fire or electric shock.

CAUTION!

The following notes concern possible physical damage to this unit and to the user. Carrying or holding this unit by the LCD monitor can result in dropping the unit, or in a malfunction. Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the unit.

CAUTION!

Connecting cables (Audio/Video, etc.) to this unit and leaving it on top of the TV is not recommended, as tripping on the cables will cause the unit to fall, resulting in damage.

When using the AC adapter in areas other than the USA

The provided AC adapter features automatic voltage selection in the AC range from 110 V to 240 V.

USING HOUSEHOLD AC PLUG ADAPTER

In case of connecting the unit’s power cord to an AC wall outlet other than American National Standard C73 series type, use an AC plug adapter called a “Siemens Plug” as shown. For this AC plug adapter, consult your nearest JVC dealer.

 Remove the AC adapter from the AC

wall outlet when not in use.

 Do not leave dust or metal objects

adhered to the AC wall outlet or AC adapter (power/DC plug).

Plug Adapter

Introduction

IMPORTANT (for owners in the U.K.) Connection to the mains supply in the United Kingdom. DO NOT cut off the mains plug from this equipment.

If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or consult your dealer.

BE SURE to replace the fuse only with

an identical approved type, as originally fitted, and to replace the fuse cover. If nonetheless the mains plug is cut off be sure to remove the fuse and dispose of the plug immediately, to avoid possible shock hazard by inadvertent connection to the mains supply. If this product is not supplied fitted with a mains plug then follow the instructions given below:

DO NOT make any connection to the

Larger Terminal coded E or Green. The wires in the mains lead are coloured in accordance with the following code:

If these colours do not correspond with the terminal identifications of your plug, connect as follows: Blue wire to terminal coded N (Neutral) or coloured black. Brown wire to terminal coded L (Live) or coloured Red. If in doubt — consult a competent electrician.

CAUTIONS:

 To prevent shock, do not open the

cabinet. No user serviceable parts inside. Refer servicing to qualified personnel.

 When you are not using the AC

adapter for a long period of time, it is recommended that you disconnect the power cord from AC outlet.

Blue to N (Neutral) or Black Brown to L (Live) or Red

FOR EUROPE

This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. This equipment is designed for professional video appliances and can be used in the following environments:

 Controlled EMC environment (for

example, purpose-built broadcasting or recording studio), and rural outdoors

environments. In order to keep the best performance and furthermore for electromagnetic compatibility we recommend to use cables not exceeding the following lengths:

The inrush current of this apparatus is

4.9 A.

Exclusive Cable

Coaxial Cable

Shielded Cable

DC INPUT 1.8 m

1.5 m

3 m

5 m

1 m

10 m

USB Mini

AV OUT

HDMI

REMOTE

HD/SD SDI

AUX

HEADPHONE

AUDIO INPUT 1/2

Port Cable Length

CAUTION:

Where there are strong electromagnetic waves or magnetism, for example near a radio or TV transmitter, transformer, motor, etc., the picture and the sound may be disturbed. In such case, please keep the apparatus away from the sources of the disturbance.

Introduction

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety. European representative of JVC KENWOOD Corporation is: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany

Sehr geehrter Kunde, sehr geehrte Kundin,

dieses Gerät stimmt mit den gültigen europäischen Richtlinien und Normen bezüglich elektromagnetischer Verträglichkeit und elektrischer Sicherheit überein. Die europäische Vertretung für die JVC KENWOOD Corporation ist: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Deutschland

WARNING

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

CAUTION:

To avoid electric shock or damage to the unit, first firmly insert the small end of the power cord into the AC Adapter until it is no longer wobbly, and then plug the larger end of the power cord in to an AC outlet.

FOR EUROPEAN

Information for Users on Disposal of Old Equipment and Batteries

[European Union]

These symbols indicate that the electrical and electronic equipment and the battery with this symbol should not be disposed of as general household waste at its end-of-life. Instead, the products should be handed over to the applicable collection points for the recycling of electrical and electronic equipment as well as batteries for proper treatment, recovery and recycling in accordance with your national legislation and the Directive 2002/96/EC and 2006/66/EC. By disposing of these products correctly, you will help to conserve natural resources and will help to prevent potential negative effects on the environment and human health which could otherwise be caused by inappropriate waste handling of these products. For more information about collection points and recycling of these products, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

(Business users)

If you wish to dispose of this product, please visit our web page http://www.jvc.eu to obtain information about the take-back of the product.

[Other Countries outside the European Union]

These symbols are only valid in the European Union. If you wish to dispose of these items, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment and batteries.

Products

Battery

The sign Pb below the symbol for batteries indicates that this battery contains lead.

Notice:

Introduction

Battery Pack

The supplied battery pack is a lithium-ion battery. Before using the supplied battery pack or an optional battery pack, be sure to read the following cautions:

 To avoid hazards

... do not burn.

When transporting, carry the battery in a plastic bag.

... do not modify or disassemble. ... do not expose the battery to

temperatures exceeding 60°C (140°F), as this may cause the battery to overheat, explode or catch fire.

... use only specified chargers.

 To prevent damage and prolong

service life

... do not subject to unnecessary shock. ... charge within the temperature range

of 10°C to 35°C (50°F to 95°F). Cooler temperatures require longer charging time, or in some cases stop charging at all. Warmer temperatures prevent complete charging, or in some cases stop charging at all.

... store in a cool, dry place. Extended

exposure to high temperatures will increase natural discharge and shorten service life.

... keep a 30% battery level if the

battery pack is not to be used for a long period of time. In addition, fully charge and then fully discharge the battery pack every 6 months, then continue to store it at a 30% battery level .

... remove from charger or powered unit

when not in use, as some machines use current even when switched off.

... do not drop or subject to strong

impact.

... do not short-circuit the

terminals. Keep it away from metallic objects when not in use.

Terminals

Introduction

Safety Precautions ............................................ 4

Contents .......................................................... 10

Introduction

Main Features ................................................. 12

Precautions for Proper Use ............................. 14

Operation Modes ............................................. 18

Names of Parts ................................................ 20

Side Control Panel ....................................... 22

SD Slot ......................................................... 23

Rear Terminal .............................................. 23

LCD Monitor ................................................ 24

Lens Section ................................................ 25

Basic System Diagram .................................... 26

Preparations

Settings and Adjustments Before Use ............. 27

Adjusting the Grip Belt ................................. 27

Attaching an External Microphone ............... 27

Attaching the Tripod ..................................... 27

Attaching the Large Eyecup ......................... 27

Opening/Closing the Lens Cover ................. 28

Attaching/Detaching the Hood ..................... 28

Power Supply .................................................. 28

Using a Battery Pack .................................... 28

Using AC Power (DC IN Power) ................... 30

Power Status Display ...................................... 30

Turning On/Off the Power ................................ 31

Initial Settings .................................................. 32

Displays on the LCD Monitor and Viewfinder .. 34

Display Screen ............................................. 34

Status Screen .............................................. 35

USB Mode Screen ....................................... 35

Warning Display ........................................... 35

Adjusting the LCD Monitor and Viewfinder ...... 36

Adjusting the LCD Monitor ........................... 36

Adjusting the Viewfinder .............................. 37

Assigning Functions to User Buttons ............... 38

Tally Lamp ....................................................... 38

SD Card ........................................................... 39

Usable Cards ............................................... 39

Formatting (Initializing) SD Cards ................ 41

Restoring the SD Card ................................. 42

Clips Recorded to SD Cards ........................ 43

Shooting

Basic Shooting Procedures ............................. 44

Selecting System Definition, File Format and Video

Format ............................................................. 45

Zoom Operation .............................................. 46

Focus Operation .............................................. 47

Adjusting the Focusing by Face Detection ...... 49

Adjusting the Brightness .................................. 50

Adjusting the Iris .............................................. 51

Setting the Gain ............................................... 52

Setting the Electronic Shutter .......................... 53

Setting the ND Filter ........................................ 55

Adjusting the White Balance ............................ 55

Adjusting the Camera Image ........................... 59

Using the Image Stabilizer ............................... 59

Audio Recording .............................................. 60

Monitoring Audio Sound During Recording Using a

Headphone ...................................................... 62

Time Code and User’s Bit ................................ 62

Setting Time Code Generator .......................... 63

Synchronizing Time Code on Another Camera

......................................................................... 66

Setting Zebra Pattern ...................................... 67

Setting Spot Meter ........................................... 68

Viewing Recorded Videos Immediately (Clip

Review) ........................................................... 70

Splitting the Clips Freely (Clip Cutter Trig) ....... 71

Dual Rec .......................................................... 71

Backup Rec ..................................................... 73

Special Recording ........................................... 75

Pre Rec ........................................................ 75

Clip Continuous Rec .................................... 76

Frame Rec ................................................... 77

Interval Rec .................................................. 78

Variable Frame Rec ..................................... 80

Playback

Playing Recorded Clips ................................... 81

Thumbnail Screen ........................................ 81

Actions ......................................................... 83

Playing back ................................................ 84

Deleting Clips .................................................. 85

Appending/Deleting OK Mark .......................... 86

Selecting and Performing Operations on Multiple

Clips ................................................................ 87

Selecting Multiple Clips Randomly ............... 87

Selecting Multiple Clips Consecutively ........ 88

Menu Display and Detailed Settings

Basic Operations in Menu Screen ................... 89

Display and Description of the Menu Screen

..................................................................... 90

Text Input with Software Keyboard .............. 91

Menu Screen Hierarchical Chart ..................... 92

Camera Function Menu ................................... 93

User Switch Set Item .................................... 95

Camera Process Menu .................................... 96

Detail/Adjust Item ......................................... 99

White Balance Item .................................... 100

TC/UB Menu ................................................. 100

LCD/VF Menu ................................................ 101

Shooting Assist Item .................................. 102

Marker Settings Item .................................. 103

Display Settings Item ................................. 103

A/V Set Menu ................................................ 105

Video Set Item ........................................... 105

Audio Set Item ........................................... 106

System Menu ................................................ 108

Record Set Item ......................................... 109

Adding/Editing Frequently Used Menu Items

(Favorites Menu) ........................................... 112

Adding Menu Items to Favorites Menu ...... 112

Editing Favorites Menu .............................. 113

Display/Status Screen

Display Screen in Camera Mode ................... 116

Display Screen in Media Mode ...................... 121

Status Screen ................................................ 123

Camera Features

Marker and Safety Zone Displays (Camera Mode

Only) .............................................................. 124

Smoothening the Skin Color (Skin Detail

Function) ....................................................... 124

Color Bar Output ........................................... 124

Adjusting Color Matrix ................................... 125

Configuring Setup Files ................................. 126

Saving Setup Files ..................................... 126

Loading a Setup File .................................. 127

Deleting Setup Files ................................... 128

Connecting External Devices

Managing/Editing Clips on a PC .................... 129

Connecting External Monitor ......................... 130

Connecting the Headphone ........................... 131

Connecting Wired Remote Control ................ 132

Others

Error Messages and Actions ......................... 133

Tally Lamp ................................................. 135

Warning Tone ............................................ 135

Troubleshooting ............................................ 136

Specifications ................................................ 138

Index ............................................................. 141

Introduction

Main Features

F11 Sensitivity, 1/3-inch Full HD 3CMOS Sensors

This camera recorder is equipped with three 1/3-

Introduction

inch 2.07M pixels full HD CMOS sensors. It delivers high image quality, high color resolution through processing of individual R, G, B color signals. 12-bit signal processing and the new 2D DNR removes dark current and optical shot noise without losing S/N and high resolution, thereby achieving high F11 sensitivity.

New Fujinon 23x Zoom Lens

It ensures high magnification of 29 mm at wide ends, and provides high sensitivity across all regions with F1.6-3.0. The zoom ring with zoom ring pin enables zooming from the wide end to the tele end in 90 degrees. Focus and iris control are also possible using separate rings.

QuickTime (MPEG-2 HD/H.264 SD)/MP4 (MPEG-2 HD)/AVCHD File Format

By inheriting the concept in ProHD memory camera recorder, this camera recorder can support various file formats, such as AVCHD and QuickTime (H.264 SD) files, as well as QuickTime (MPEG-2 HD) files that can be directly edited on Apple Final Cut Pro and MP4 files that are most suitable for XDCAM EX Nonlinear Editing Workflow.

Two SDHC/SDXC Card Slots for Dual, Backup and Series Recording

The most common SDHC/SDXC card recording system is used as the memory card. This ensures reliability and operation at low running cost. Various user friendly recording systems are also available. These include dual recording of the same file to two cards, and using REC/STBY to break up video clips in one card while performing backup recording to the other card.

Small, Lightweight, Stylish, and Ergonomic Design

The camera recorder is only 2.4 kg in operation mode. It is light and easy to use. Its ergonomic design takes into consideration portability and operability and is easy on the hand during shooting.

JVC’s Proprietary FALCONBRID HighQuality Imaging Engine

The FALCONBRID high-quality imaging engine omits unnecessary processing through incorporating camera processing and image compression on a single chip. Images from imaging devices are compressed and processed without any loss thereby achieving high-quality images.

MPEG2 and H.264 Codec

FALCONBRID allows users to select MPEG-2 and AVCHD, the most commonly used codec for professional video, as the recording format.

Variable Frame Rec

Enables beautiful slow motion and quick motion image recording such as overcrank and undercrank.

SDI/HDMI Simultaneous Output

Equipped with both [HD/SD SDI] and [HDMI] terminals as digital output.

Non-compressed full HD video signals and audio signals can be output to the [HD/SD SDI] and

[HDMI] terminals at the same time.

Auto Focus/Optical Image Stabilizer

The camera recorder is equipped with a face detection auto focus function that covers the entire screen. It can switch to manual focus as well. A built-in optical image stabilizer feature is also available.

Professional Switch Layout and Various Video Parameter Settings

Switches for Gain and White Balance are available on the side panel to enable quick switchings according to the shooting scene. Image parameters such as gamma and color matrixes are also available in the menu for adjusting preferred tones.

4-position ND Filter

This camera recorder incorporates three types of ND filters. Adjust the amount of light according to the brightness during shooting by switching the 4position ND filter (OFF, 1/4, 1/16, 1/64).

0.45-inch 1.22M Pixel Color Viewfinder,

3.5-inch 920K Pixel LCD Display (Equipped with Focus Assist Function)

Built-in Stereo Microphone, 2-channel XLR Audio Input (Microphone/Line Switch, Phantom Power Supply) and Mini Jack Input Terminal for Wireless Microphone Receiver

Pre Rec Function (Up to 15 Seconds) and Interval Rec Function

Supports Wired Remote Control

Application Software Provided

The [JVC ProHD Clip Manager] application software is provided for you to copy recorded clips

to Windows or Macintosh computers and for checking the video images. (For MP4 file format)

The disc provided with this camera recorder comes with [JVC ProHD Clip Manager] and other

application software as well as their user guides. * For details, refer to the user guides for each

application software.

How to use this manual

Symbols used

Caution : Describes precautions concerning the

Memo : Describes reference information, such

Content of this manual

operation of this product.

as functions and usage restrictions of this product.

: Indicates the reference page numbers

and reference items.

Illustrated designs, specifications and other contents of this manual are subject to change for improvement without prior notice. AVCHD and the AVCHD logo are trademarks of Panasonic Corporation and Sony Corporation. SDXC and SDHC logos are trademarks of SD-3C, LLC.

HDMI (High-Definition Multimedia Interface) and 1 are trademarks of HDMI Licensing, LLC.

QuickTime, Final Cut Pro and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries. Android is a trademark and/or registered trademark of Google Inc. QR Code is a registered trademark of Denso Wave Incorporated. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Microsoft, Windows, Windows Vista, and Windows 7 are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Other product and company names included in this instruction manual are trademarks and/ or registered trademarks of their respective companies. Marks such as ™ and ® have been omitted in this manual.

Introduction

Precautions for Proper Use

Transportation

Do not drop or hit this unit against a hard object when transporting.

Storage and Usage Locations

Introduction

o Allowable ambient temperature and humidity Be sure to use this unit within the allowable temperature range of 0 °C to 40 °C (32 °F to 104°F) and a relative humidity of 30 % to 80 %. Using this unit at a temperature or humidity outside the allowable ranges could result not only in malfunction but also serious impact on the CMOS elements as small white spots may be generated. Please exercise care during use. o Strong electromagnetic waves or magnetism Noise may appear in the picture or audio and/or the colors may be incorrect if this unit is used near a radio or television transmitting antenna, in places where strong magnetic fields are generated by transformers, motors, etc., or near devices emitting radio waves, such as transceivers or cellular phones. o Use of wireless microphone near this unit When a wireless microphone or wireless microphone tuner is used near this unit during recording, the tuner could pick up noise. o Avoid using or placing this unit in the following places.

Places subject to extreme heat or cold

Places with excessive dirt or dust

Places with high humidity or moisture

Places subject to smoke or vapor such as near a cooking stove

Places subject to strong vibrations or unstable surfaces

In a parked car under direct sunlight or near a

heater for long hours o Do not place this unit at places that are subject to radiation or X-rays, or where corrosive gases occur. o Protect this unit from being splashed with water. (Especially when shooting in the rain) o Protect this unit from getting wet when shooting on a beach. In addition, salt and sand may adhere to the body. Be sure to clean the unit after use. o Protect this unit against penetration of dust when using it in a place subject to sandy dust.

Power Saving

When this unit is not in use, be sure to set the [POWER ON/OFF(CHG)] switch to “OFF(CHG)” in

order to reduce power consumption.

Maintenance

o Turn off the power before performing any maintenance. o Wipe the external cabinet of the unit with a soft cloth. Do not wipe the body with benzene or thinner. Doing so may cause the surface to melt or turn cloudy. When it is extremely dirty, soak the cloth in a solution of neutral detergent, wipe the body with it, and then use a clean cloth to remove the detergent.

Rechargeable Battery

o Be sure to use only the specified batteries. We do not guarantee the safety and performance of this device if an unspecified battery is used.

o The battery is not charged when purchased. o When using the battery in a low temperature

environment (10°C/50 °F or below), the operating time may be shortened, or it may not function properly. When using the device outdoors in the winter weather, warm the battery, such as by placing it in the pocket, before attaching it. o Do not expose the battery to excessive heat, such as direct sunlight or fire. o If the battery is not to be used for a long time

Use up the charge completely and detach it from the camera to prevent deterioration. (Wait for the battery to run out by itself such as through continuous shooting or playback.)

Charge the battery once every half a year, and

store it again after using up the charge. o Store the removed battery in a dry place between 15 °C and 25 °C (59 °F and 77 °F).

o ATTENTION:

The product you have purchased is powered by a rechargeable battery that is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery.

Regular Inspection (Maintenance)

Groove

Under normal environment, dust will accumulate on the camera recorder when it is used over a long period. Dust may enter the camera recorder especially if it is used outdoors. This may affect the image and sound quality of the camera recorder. Check and replace the fan after every 9000 hours (suggested guideline). You can check the usage time of the fan in [System] B [System Information] B [Fan Hour].

(A P109 [ Fan Hour ] )

If the fan is used for more than 9000 hours without replacement, “FAN MAINTENANCE REQUIRED”

will be displayed every time you turn on the power.

SDHC/SDXC Cards

o SDHC/SDXC card is referred to as “SD card” in this manual. o This camera recorder saves the recorded images and audio sound on the SD card (sold separately) in the card slot. o Use an SD card (4 GB to 128 GB) with Class 6 or higher performance, formatted using this camera recorder. o Depending on the recording format, SD card with Class 4 or higher performance can also be used.

(A P45 [Selecting System Definition, File Format and Video Format] )

* Using cards other than those from Panasonic,

TOSHIBA or SanDisk may result in recording failure or data loss.

o If the SD card contains files recorded by devices other than this camera recorder or files that are saved from a PC, the recordable time may be shorter or data may not be properly recorded. In addition, the remaining space on the card may not increase even when files are deleted using a PC.

Handling of SD Cards

o The status indicator lights up in red when data on the SD card is being accessed. Do not remove the SD card during data access (such as recording, playback, or formatting). Do not turn off the power or remove the battery and AC adapter during access either. o Do not use or store the SD card in a place that is subject to static electricity or electrical noise. o Do not place the SD card near locations that are exposed to strong magnetic fields or radio waves. o Inserting the SD card incorrectly may result in damage of this unit or the SD card.

o We are not liable for any accidental loss of data stored on the SD card. Please back up any important data. o Make use of the SD card within the prescribed conditions of use. Do not use it at the following locations. Places that are subject to direct sunlight, high humidity or corrosion, places near thermal equipment, sandy or dusty places, or in a car under the sun with the doors and windows closed. o Do not bend or drop the SD card, or subject it to strong impact or vibration.

o Do not splash the SD card with water. o Do not dismantle or modify the SD card. o Do not touch the terminals with your hands or

with a metal object. o Do not allow dust, dirt, water, or foreign objects to adhere to the terminals. o Do not remove the labels or stick other labels or stickers on the SD cards. o Do not use pencils or ballpoint pens to write on the SD cards. Always use oil-based pens. o If you format (initialize) the SD card, all data recorded on the card, including video data and setup files, will be deleted. o You are recommended to use cards that are formatted (initialized) on this camera recorder.

The SD card may be damaged if the camera

recorder is not operated correctly. Formatting

(Initializing) the SD card may allow it to operate

correctly.

SD cards that have been formatted (initialized)

on other cameras, computers or peripheral

equipment may not operate correctly. In this

case, format (initialize) the SD card on this

camera recorder. o If you want to wipe out all information by completely erasing the data, we recommend either using commercially available software that is specially designed for that purpose, or by physically destroying the SD card with a hammer, etc. When formatting or erasing data using the camera recorder, only the file administration information is changed. The data is not completely erased from the SD card. o Some commercially available SD cards may be harder to be removed from this unit. Remove them by hooking onto the groove on the cards.

It will be easier to remove the cards after several

times.

Do not stick any stickers on the cards.

Introduction

o The SD card may pop out when it is being

removed. Be careful not to lose the card.

Others

o Do not insert objects other than the memory card into the card slot. o Do not block the vent on the unit. Blocking of the vent causes internal heating and may lead to burns and fires.

Introduction

o Do not turn off the [POWER ON/OFF(CHG)] switch or remove the power cable during recording

or playback. o The camera recorder may not show stable pictures for a few seconds immediately after the power is turned on, but this is not a malfunction. o When the video signal output terminals are not in use, put on the covers to prevent damage to the terminals. o Do not drop this unit or subject it to strong impact or vibration as it is a precision equipment. o Optical performance of lens Due to the optical performance of the lens, color divergence phenomena (magnification chromatic aberration) may occur at the periphery of the image. This is not a camera malfunction. o Noise may appear in the image when switching modes. o If placed on its side, heat release efficiency will deteriorate. o Use the supplied AC adapter as the power supply. Do not use the supplied AC adapter on other devices. o When the connectors that come with connector covers are not in use, put on the covers to prevent damage to the connectors.

LCD Monitor and Viewfinder

o The LCD monitor and viewfinder screen are manufactured using high-precision technology. Black spots may appear on the LCD monitor and viewfinder screen, or red, blue, and/or white spots may not disappear. However, this is not a malfunction and these spots are not recorded on the SD card. o If you use this unit continuously for a long period of time, the characters displayed in the viewfinder may temporarily remain on the screen. This is not recorded on the SD card. They will not appear after you turn the power off and then on again. o If you use this unit in a cold place, the images may appear to lag on the screen, but this is not a malfunction. Retained images are not recorded on the SD card. o Do not press against the surface with force or subject it to strong impact. Doing so may damage or break the screens. o Noise may appear in the viewfinder when switching between the live video and playback images. o Due to the characteristic of the viewfinder display device, colors may appear on the images when you blink your eyes. It does not affect the recorded images, SDI output, or HDMI output.

Any recordings made on this camera recorder that are played back for profit or public preview may infringe on the rights of the owner of the recordings. Do not use the recordings for purpose other than personal enjoyment without prior consent from the owner.

License Notices

o MPEGLA AVC THIS PRODUCT IS LICENSED UNDER THE AVC PATENT PORTFOLIO LICENSE FOR THE PERSONAL USE OF A CONSUMER OR OTHER USES IN WHICH IT DOES NOT RECEIVE REMUNERATION TO (i) ENCODE VIDEO IN COMPLIANCE WITH THE AVC STANDARD (“AVC VIDEO”) AND/OR (ii) DECODE AVC VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED TO PROVIDE AVC VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE

HTTP://WWW.MPEGLA.COM

o MPEGLA MPEG-2 Patent ANY USE OF THIS PRODUCT IN ANY MANNER OTHER THAN PERSONAL USE THAT COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2 PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, LLC, 6312 S. Fiddlers Green circle, Suite 400E, Greenwood Village, Colorado 80111 U.S.A.

Introduction

Operation Modes

AE LEVEL

MENU/THUMB

CANCEL

MODE

Media Mode

Thumbnail

Display

(Playback/Pause/ Frame-by-Frame/

Fast Forward/Rewind/

Clip Jump)

Playback

USB Connection (When the confirmation to change to USB mode appears and [Change] is selected)

(USB Mass Storage Class)

USB Mode

Stop Button

Stop

Button

Playback Button

Playback

Button

Connection disabled on PC

Press and hold [MODE] button

[MODE] Button

Camera

Mode

This camera recorder has three operation modes - Camera mode, Media mode, and USB mode.

Introduction

Operation Mode Description

Camera Mode

This is the camera shooting mode. The camera recorder starts up in Camera mode when the power is turned on.

Camera images are output on the viewfinder and LCD monitor. When a recordable SD card is inserted, the camera recorder enters the recording standby mode. “STBY” appears on the operation mode display area of the

LCD monitor and viewfinder.

Press the [REC] trigger button to start recording.

Memo :

Playback of SD card is not possible in Camera mode. However, you can check the most recently recorded video clip.

(A P70 [Viewing Recorded Videos Immediately (Clip Review)] )

Introduction

Media Mode

USB Mode

This mode allows you to play back or delete clips recorded on the SD card.

When a playable SD card is inserted, the thumbnail or playback screen is displayed on the viewfinder and LCD monitor.

Press the [MODE] selection button to enter Media mode when you are not shooting in Camera mode. Once the camera recorder is in Media mode,

thumbnails of the selected media slot are displayed.

This mode allows you to connect to a PC and transfer the files on an SD card to the PC.

When the camera recorder is connected to a USB cable, the message “Change to USB Mode?” appears.

Select [Change] and press the Set button to switch to USB mode.

(A P129 [Managing/Editing Clips on a PC] )

In USB mode, the camera recorder is recognized by the connected PC as a peripheral drive. (USB mass storage class only) Disable the connection on the PC and remove the USB cable from the camera recorder to switch to Camera mode.

(A P129 [Managing/Editing Clips on a PC] )

Memo :

When a USB cable is connected during recording, the message appears after recording stops.

If playback is in progress, the message appears once the files are closed automatically, such as when playback stops.

Files on the PC cannot be written to the SD card.

Names of Parts

SERVO MANUAL

ZOOM

REC

FIX VAR OFF

MENU/THUMB

AE LEVEL

FOCUS

ND FILTER

1/64

1/1

1/4

OFF

KER/6

ZEBRA/5

AE LOCK/4

SHUTTER

HT BAL

CANCEL P

GAIN

FULL AUTO

PUSH AUTO

PRESET

B L M H

MANU

∞

MODE

(CHG)

SLO

A/B

TIME CODE

AUTO

Bottom

Introduction

Built-in Microphone

(A P60 [Audio Recording] )

Tally Lamp

(A P38 [Tally Lamp] ) (A P135 [Tally Lamp] )

Microphone Holder

(A P27 [Attaching an External Microphone] )

Microphone Holder Lock Knob

(A P27 [Attaching an External Microphone] )

Shoe

For mounting separately sold lights and accessories.

[FIX/VAR/OFF] Zoom Speed Switch

(A P46 [Zoom Operation] ) For switching the zoom speed of the zoom lever

at the handle.

Accessory Mounting Screw Hole

Tripod Mounting Hole

(A P27 [Attaching the Tripod] )

[REC] Record Trigger Button

Starts/stops recording.

Memo :

This button is interlocked with the [REC] button R on the grip and the [REC/HOLD] button Z at the top of the handle.

[ZOOM SERVO/MANUAL] Zoom Operation Servo/Manual Switch

Set to “SERVO” when using the zoom lever at the grip j or the zoom lever at the handle a. (A P46 [Zoom Operation] )

Monitor Speaker

(A P84 [Audio Output during Playback] )

Viewfinder

(A P36 [Adjusting the LCD Monitor and Viewfinder] )

Visibility Adjustment Lever

(A P36 [Adjusting the LCD Monitor and Viewfinder] )

Eyecup

Prevents external light from entering the viewfinder screen and cameraman’s vision. (A P27 [Attaching the Large Eyecup] )

Battery

(A P28 [Using a Battery Pack] )

[x] Headphone Jack (Φ3.5 mm)

(A P62 [Monitoring Audio Sound During Recording Using a Headphone] )

[AUX] AUX Input Terminal (Φ3.5 mm)

For connecting to receiver such as wireless microphone.

INPUT2

INPUT1

DEVICE

BATT

.RELEA

HDMI

REMOTE

HD/SD

SDI

REC

HOLD

OUT

M N

S T

[REC] Record Trigger Button

Starts/stops recording.

Memo :

This button is interlocked with the [REC] button I at the bottom of the lens and the [REC/ HOLD] button Z at the top of the handle.

[C.REVIEW/7] Clip Review/User 7 Button

For checking the most recently captured images. (A P70 [Viewing Recorded Videos Immediately (Clip Review)] ) You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

Zoom Lever at the Grip

To operate zoom servo with the zoom lever at the grip, set the [ZOOM SERVO/MANUAL]

switch 0 to “SERVO”. (A P46 [Using the Zoom Lever at the Grip] )

[TC] TC Input/Output Terminal

(A P62 [Time Code and User’s Bit] )

[IN/OUT] TC IN/OUT Selection Switch

(A P66 [Synchronizing Time Code on Another Camera] )

Hood Release Button

(A P28 [Attaching/Detaching the Hood] )

External Microphone Cable Clamp

(A P27 [Attaching an External Microphone] )

[INPUT1/INPUT2] Audio Input Terminal 1, 2 (XLR 3-pin x 2)

(A P27 [Attaching an External Microphone] )

[REC/HOLD] Record Trigger Button/Lock Switch

Starts/stops recording. Set the switch to [HOLD] to lock the [REC]

Trigger button.

Memo :

This button is interlocked with the [REC] button R on the grip and the [REC] button I at the bottom of the lens.

The [REC] button R on the grip and the [REC] button I at the bottom of the lens will not be locked.

Zoom lever at the Handle

(A P46 [Using the Zoom Lever at the Handle] )

Shoulder Belt Mount (x2)

For mounting a shoulder belt (sold separately).

Caution :

Be sure to use a shoulder belt with the strength to withstand the weight of this camera recorder.

If the shoulder belt is not properly attached, the camera recorder may fall and cause injuries.

Check the instruction manual provided with the shoulder belt before using.

[POWER/CHG] Power/Charging Display Lamp

(A P28 [Using a Battery Pack] )

[BATT. RELEASE] Battery Lock Release Button

(A P29 [Removing the Battery] )

Introduction

ND FILTER

FOCUS

AE LEVEL

MANU

PUSH AUTO

MENU/THUMB

FOCUS ASSIST/1 OIS / 2 LOLUX / 3

1/64

1/16

1/4

OFF

PRESET

IRIS

GAIN

CANCEL

B A

WHT BAL SHUTTER

FULL AUTO

MODE

POWER

OFF

(CHG)

OFF

AE LOCK/4 ZEBRA/5 MARKER/6

PUSH AUTO

TIME CODE

AUTO

S R Q

MLKJ

F G

Introduction

Side Control Panel

[FOCUS AUTO/MANU/∞] Focus Switch

(A P47 [Focus Operation] )

[ND FILTER] ND Filter Switch

(A P55 [Setting the ND Filter] )

[PUSH AUTO] Focus Push Auto Button

(A P48 [One Push Auto Focus] )

[IRIS] Iris Auto/Manual Selection Button

(A P51 [Adjusting the Iris] )

[PUSH AUTO] Iris Push Auto Button

(A P51 [Adjusting the Iris] )

[GAIN] Gain Auto/Manual Selection Button / [L/ M /H] Sensitivity Selection Switch

(A P52 [Setting the Gain] )

[WHT BAL] White Balance Auto/Manual Selection Button / [B/A/PRESET] Selection Switch

(A P55 [Adjusting the White Balance] )

[SHUTTER] Shutter Speed Auto/Manual Selection Button

(A P53 [Setting the Electronic Shutter] )

[y] One Push Auto White Balance Button

[FULL AUTO ON/OFF] Full Auto Switch

(A P50 [Adjusting the Brightness Automatically] ) (A P58 [Automatic White Balance Mode (FAW: Fulltime Auto White balance)] )

[AE LOCK/4] AE Lock/User 4 Button

When Gain, Iris, and Shutter are set to “AUTO”, their respective values and the value of white

balance are locked when the [AE LOCK/4] button is pressed.

You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

[ZEBRA/5] Zebra/User 5 Button

(A P67 [Setting Zebra Pattern] ) You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

[MARKER/6] Marker/User 6 Button

This button toggles ON/OFF the marker, safety zone, and center mark displays. You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

[MODE] Camera/Media Mode Selection Button

(A P18 [Operation Modes] )

[POWER ON/OFF(CHG)] Lock Power ON/OFF Switch

Turns ON/OFF the power.

Hold down the lock button (blue) in the center to toggle ON/OFF.

When the power is turning OFF, “P.OFF” appears on the LCD monitor and viewfinder.

Wait for 5 seconds or more to turn on the power again.

Cross-Shaped Button (JKHI)/Set Button (R)

The function changes according to the operation status of the camera recorder. o During menu operation (all modes) (A P89 [Basic Operations in Menu Screen] )

Center Set button (R) : Confirms menu items

and setting values Cross-shaped button (JK)

: Selects menu items

and setting values

o During Camera mode Shutter operation:

Center Set button (R) : Shutter ON/OFF Cross-shaped button (JK)

: Switches shutter

speed when shutter

is ON AE level operation : Cross-shaped button

(HI)

Memo :

When [Camera Function] B [AE LEVEL SW] is set to “AE LEVEL/VFR”, the cross-shaped button (HI) is used to set the number of frames during Variable Frame Rec.

(A P80 [Variable Frame Rec] ) (A P94 [ AE LEVEL SW ] )

[LOLUX/3] Low-light Shooting/User 3 Button

For switching the low-light shooting mode ON or OFF. You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

DEVICE

HDMI

REMOTE

HD/SD

SDI

POWER /CHG

BATT.RELEASE

OPEN

DEVICE

REMOTE

C D

[OIS/2] Optical Image Stabilizer/User 2 Button

For switching the image stabilizer feature mode ON or OFF. You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

[FOCUS ASSIST/1] Focus Assist/User 1 Button

For switching the focus assist function ON or OFF. (A P48 [Focus Assist Function] ) You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

[MENU/THUMB] Menu/Thumbnail Button

Displays the menu screen during Camera mode.

(A P89 [Basic Operations in Menu Screen] )

Displays the menu screen when the button is pressed during thumbnail display in the Media mode.

Stops playback and displays the thumbnail screen when the button is pressed during playback screen display in the Media mode.

[CANCEL] Cancel Button

Cancels various settings and stops playback.

SD Slot

(A P39 [SD Card] )

Rear Terminal

[DEVICE] USB Mini Terminal

(A P129 [Managing/Editing Clips on a PC] )

[AV] AV Output Terminal

(A P130 [Connecting External Monitor] )

[HD/SD SDI] SDI Output Terminal (BNC)

(A P130 [Connecting External Monitor] )

[HDMI] HDMI Output Terminal

(A P130 [Connecting External Monitor] )

[REMOTE] Remote Terminal

(A P132 [Connecting Wired Remote Control] )

[DC] DC Input Terminal

Input terminal for DC 12 V power supply. For connnecting with the supplied AC adapter. (A P30 [Using AC Power (DC IN Power)] )

Introduction

SD Card Cover

[SLOT A/B] Card Slot Selection Button

For switching the active card slot during shooting and playback.

Card Slot B Status Indicator

Card Slot A Status Indicator

LCD Monitor

MENU/THUMB

CANCEL

CH1

INT INPUT1 INPUT2

AUTO MANUAL

CH2

INPUT2

MONITOR

DISPLAY STATUS

INPUT1

PEAKINGLCD BRIGHT

CH2CH1

LINE MIC MIC +48V

CH1

BOTH

CH2

H I

JKLNM

Introduction

LCD Monitor

(A P36 [Adjusting the LCD Monitor and Viewfinder] )

[MENU/THUMB] Menu/Thumbnail Button

Displays the menu screen during Camera mode.

(A P89 [Basic Operations in Menu Screen] )

Displays the menu screen when the button is pressed during thumbnail display in the Media mode.

Stops playback and displays the thumbnail screen when the button is pressed during playback screen display in the Media mode.

LCD Cross-Shaped Button (JKHI)/Set Button (R)

The function changes according to the operation status of the camera recorder.

During menu operation (all modes)

(A P89 [Basic Operations in Menu Screen] )

Center Set button (R) : Confirms menu

items and setting

values Cross-shaped button (JK)

: Selects menu

items and setting

values

During Camera mode You can also use it as a user button by assigning a specific feature in the menu setting to this button. (A P38 [Assigning Functions to User Buttons] )

[CANCEL] Cancel Button

Cancels various settings and stops playback.

[CH1/CH2] CH1/CH2 Recording Level Adjustment Knob

(A P60 [Audio Recording] )

[LCD BRIGHT +/-] LCD Display Brightness Adjustment Button

(A P36 [Adjusting the Brightness] )

[PEAKING +/-] LCD/VF Contour Adjustment Button

(A P37 [Adjusting the Contour (LCD)] ) (A P37 [Adjusting the Contour (Viewfinder)] )

[DISPLAY] Display Button

Press the [DISPLAY] button to switch to the display screen during normal screen display

(when the menu screen is not displayed).

(A P34 [Display Screen] )

Switches between [Main Menu] and [Favorites Menu] when the [DISPLAY] button is pressed while the menu screen is

displayed.

(A P89 [Basic Operations in Menu Screen] )

[STATUS] Status Screen Display Button

Press the [STATUS] button to display the status screen on the viewfinder and LCD monitor

during normal screen display (when the menu screen is not displayed). (A P35 [Status Screen] )

[MONITOR]/[+/-] Audio Monitor Selection Switch/Volume Adjustment Button

Switches the audio monitor and adjusts the monitor speaker/headphone. (A P62 [Monitoring Audio Sound During Recording Using a Headphone] )

[INPUT1/INPUT2] Audio Input Signal Selection Switch

(A P60 [Audio Recording] )

[CH2] CH2 Audio Input Signal Selection Switch

Select the audio input terminal to record to CH2. (A P60 [Audio Recording] )

[CH1] CH1 Audio Input Signal Selection Switch

(A P60 [Audio Recording] )

[CH1/CH2 AUTO/MANUAL] CH1/CH2 Audio Recording Mode Switch

(A P61 [Adjusting Audio Recording Level] )

Lens Section

Filter Built-In Screw

Transparent or UV filter for lens protection,

or filters for various effects can be installed.

Installable filter types: Φ72mmP0.75

Memo :

Remove the lens hood when installing the filter.

(A P28 [Attaching/Detaching the Hood] )

Lens Cover Open/Close Switch

(A P28 [Opening/Closing the Lens Cover] )

Focus Ring

(A P47 [Focus Operation] )

Zoom Ring

(A P46 [Zoom Operation] ) To operate zoom with this ring, set the [ZOOM SERVO/MANUAL] switch to “MANUAL”.

Iris Ring

(A P51 [Adjusting the Iris] ) To operate auto iris, press the [IRIS] button on the side control panel. (a mark appears on the screen)

Introduction

Basic System Diagram

Wireless Microphone Receiver

RCA pin

AV C abl e

HDMI Cable

[AUX]

[TC]

Carrying Case

Tripod

SDHC/SDXC

Memory Card

SDHC/SDXC

Card Reader

USB Cable

Battery

AC Adapter

Remote Control Unit

Non-linear Editing

System

GY-HM600

Microphone

Monitor

SDI Cable BNC

Earphone

Shoulder Belt

GY-HM600

Introduction

Settings and Adjustments

INPUT2

INPUT1

B A T

T . R

E L E

A S

P O

E R

R EM

O TE

HD/SD

SDI

REC

1, 3

o Bottom

Large Eyecup (supplied)

Eyecup

Before Use

Adjusting the Grip Belt

Open the pad and adjust the position of the grip belt accordingly.

Caution :

If the grip is loose, the camera recorder may fall off resulting in injuries or malfunction.

Attaching an External Microphone

You can attach a separately sold microphone to the microphone holder.

Turn the knob on the microphone holder anticlockwise to loosen and open the microphone holder.

Place the microphone in the microphone holder.

Turn the knob on the microphone holder clockwise to secure the microphone.

5 6

Connect the microphone cable to the [INPUT1] or [INPUT2] terminal.

Pin the microphone cable to the clamp. Perform the settings for the microphone

correctly.

(A P60 [Audio Recording] )

Attaching the Tripod

Use the screw hole at the bottom of this camera recorder. (3/8×16UNC, 1/4×20UNC) Use the screw hole that suits the tripod. To prevent the camera recorder from falling off, which may result in injuries or damages, read the instruction manual of the tripod to be used and make sure that it is securely attached.

Caution :

Use the tripod on a stable surface.

To prevent the camera recorder from falling, attach securely using the rotation prevention hole.

Use screws with screw length 5 mm and below.

Attaching the Large Eyecup

Attach the large eyecup (supplied) to prevent external light from entering the viewfinder screen and cameraman’s vision.

Align and attach to the groove of the eyecup mounted on the camera recorder.

The large eyecup can be attached in any direction.

Memo :

Do not remove the eyecup that is premounted on the camera recorder.

Preparations

Opening/Closing the Lens Cover

POWER

/CHG

MODE

POWER

OFF

(CHG)

Use the lens cover open/close switch to open or close the lens cover. Before shooting, open the lens cover. When this camera recorder is not in use, close the lens cover to protect the lens.

Preparations

Caution :

Do not press against the lens cover with force. Doing so may damage the lens or the cover.

Attaching/Detaching the Hood

Attaching the Hood

Align the markings on the camera recorder and hood; turn the hood in the direction of the arrow until it is locked.

Detaching the Hood

Remove the hood when attaching a filter, teleconverter or wide converter to the front of the lens.

While pressing the hood release button, turn the hood in the anti-clockwise direction to remove it.

Power Supply

To use this camera recorder, you can attach a battery pack or connect an AC adapter to it.

(A P28 [Using a Battery Pack] ) (A P30 [Using AC Power (DC IN Power)] )

Caution :

Set the [POWER ON/OFF(CHG)] switch to “OFF(CHG)” before changing the power supply that operates this camera recorder.

Using a Battery Pack

Charging the Battery

Charge the battery immediately after purchase or when the battery power is running low.

* The battery is not charged when purchased.

MODE

POWER

OFF

(CHG)

Hold down the lock button (blue) at the center of the [POWER ON/OFF(CHG)] switch

to set to “OFF(CHG)”.

Attach the supplied battery.

Slide it in until you hear a click.

Connect the supplied AC adapter to the [DC] terminal.

Open the cover of the [DC] terminal and connect as shown in the diagram.

Connect the AC adapter to a power outlet.

The [POWER/CHG] lamp blinks during

charging and will go out after charging is

complete.

Remove the AC adapter after charging is

complete.

Memo :

Blinking of the [POWER/CHG] lamp during charging indicates the charge level.

[POWER/CHG] Lamp

Orange blinking

Charge Level

Less than 25%

(4 times per second)

Orange blinking

Less than 50%

(3 times per second)

Orange blinking

Less than 75%

(2 times per second)

Orange blinking

Less than 100%

(1 time per second)

Light goes out Fully charged

Removing the Battery

Caution :

Do not remove the battery when the [POWER ON/OFF(CHG)] switch is “ON”.

Do not insert or remove the DC cable when the battery is in use.

Leaving the camera recorder unused with the battery inside will deplete the battery power even if you set the [POWER ON/OFF(CHG)]

switch to “OFF(CHG)”. Remove the battery if you are not using the camera recorder.

Estimated Charging and Continuous Operating Times

o Charging Time (supplied SSL-JVC50 battery pack) Approx. 4 h

Memo :

Use up the charge completely before you charge the battery. If the battery is not fully discharged before charging, the battery capacity may drop after repeated cycles.

If the battery capacity drops due to repetitive shallow charging and discharging, it may be recovered by using up the charge completely and then fully charging the battery again.

If you charge the battery immediately after using while the battery is still warm, it may not be fully charged.

It is recommended that you charge the battery in an environment between 10 °C and 35 °C (50 °F and 95 °F). The battery may not be fully charged or the charging time may be prolonged if charged under low temperatures (below 10 °C/ 50 °F).

Preparations

o Continuous Operating Time (supplied SSLJVC50 battery pack) Approx. 2 hrs 45 mins

Memo :

Actual operating times may differ depending on the age of the battery, charging condition, and operating environment.

Operating time is shortened in cold environment.

The operating time may shorten when power zoom is used, accessories are connected, or when the LCD monitor is frequently used.

Hold down the lock button (blue) at the center of the [POWER ON/OFF(CHG)] switch

to set to “OFF(CHG)”.

While pressing and holding the [BATT. RELEASE] button, push up and remove the battery in the direction of the arrow.

For purchase of spare batteries and battery charger, consult your nearest JVC dealer.

Precautions for Batteries

Store the battery in a cool and dry place when not in use. Do not expose the battery to high temperatures (such as in a car under direct sunlight). This will cause battery leakage and shorten the battery life.

If the operating time shortens drastically even after charging, the battery may be reaching the end of its life. Replace the battery with a new one.

Using AC Power (DC IN Power)

MODE

POWER

OFF

(CHG)

100min

50min

282min

P13000K

1/100

F1. 6

AE+6

ND 1 /6 4

5 . 6 f t

12 :34 :56

Jan 24 ,2012

00:00 :00.00

1920x1080 60i HQ

4030 20100

Use the supplied AC adapter to operate the camera recorder with AC power.

Preparations

Connect the DC cable of the AC adapter to the [DC] terminal of the camera recorder.

Check that the power switch of the camera

recorder is set to “OFF(CHG)”.

Open the cover of the [DC] terminal and

connect as shown in the diagram.

Hold down the lock button (blue) at the center of the [POWER ON/OFF(CHG)] switch

to set to “ON”.

Power will be supplied to the camera recorder.

Caution :

Do not insert or remove the DC cable during recording.

Do not use power supply of high voltage fluctuation, containing noise such as ripple, or with insufficient capacity.

Power Status Display

Viewfinder Screen and LCD Monitor

The power status is displayed on the display and menu screens.

Display Description

B 7.4V B 100min C 30% 4 RES

Memo :

If the supplied battery (or equivalent battery sold separately) is not used, the battery mark which indicates the battery level may not appear.

Display Screen

(A P116 [Display Screen in Camera Mode] ) (A P121 [Display Screen in Media Mode] )

Currently powered by a battery. When the battery power runs out, the battery mark appears hollow, and “RES” (yellow) is displayed.

Memo :

You can set the display using [LCD/VF] B [Display Settings]

B [Battery].

(A P104 [ Battery ] )

Currently powered by an AC adapter.

Charging the Built-In Battery

The date/time and time code data are stored using the built-in rechargeable battery.

When power is connected to the camera recorder, the built-in battery always gets charged. When the power is disconnected, the battery gradually discharges.

The battery will be totally discharged if left unused for 3 months and the date/time and time code data will be reset. When this happens, set the [POWER ON/OFF(CHG)] switch to “ON” to

display the [Initial Setting] screen, then set the date/time.

(A P32 [Initial Settings] )

Menu Screen

(A P90 [Display and Description of the Menu Screen] )

+ 114 hidden pages