JVC GZEX310RUS, GZ-EX310, GZEX310BUS, GZEX310AUS, GZEX355BUS User Manual

Basic User Guide

Basic User Guide(this manual)

.

Verifying the Accessories

AC Adapter

AC-V11U

Battery Pack
BN-VG114U

USB Cable

(Type A - Mini Type B)

CD-ROM

Basic User Guide

(this manual)

AV Cable

QAM1322-001

Please consult your JVC dealer or the nearest JVC service center when
purchasing a new AV cable.

BC mark means complies with Energy Efficiency Law.

BC

HD MEMORY CAMERA

GZ-EX355 A
GZ-EX310 A

LYT2605-001A-M

EN

Detailed User Guide

.

For more details on operating this
product, please refer to the “Detailed
User Guide” at the following website.

http://manual3.jvckenwood.com/

o

index.html/

Dear Customers

Thank you for purchasing this JVC product.
Before use, please read the Safety Precautions
and Cautions on p. 2 and p. 18 to ensure
safe use of this product.

Mobile User Guide

.

When you are outside, refer to the
“Mobile User Guide”. Mobile User Guide
can be viewed with standard browser for
Android tablet and iPhone.

http://manual3.jvckenwood.com/mobile/

o

us/

For Future Reference:

Enter the Model No. (located on the bottom of the camera)
and Serial No.
(located on the battery pack mount of the camera) below.

Model No.
Serial No.

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK
HAZARD, DO NOT EXPOSE THIS UNIT TO
RAIN OR MOISTURE.

NOTES:

•

The rating plate and safety caution are on the

bottom and/or the back of the main unit.

•

The serial number plate is on the battery pack

mount.

•

The rating information and safety caution of the

AC adapter are on its upper and lower sides.

Caution on Replaceable lithium battery

The battery used in this device may present a fire
or chemical burn hazard if mistreated.
Do not recharge, disassemble, heat above 100°C
(212°F) or incinerate.
Replace battery with Panasonic, Sanyo, Sony or
Maxell CR2025.
Danger of explosion or Risk of fire if the battery is
incorrectly replaced.

•

Dispose of used battery promptly.

•

Keep away from children.

•

Do not disassemble and do not dispose of in fire.

For USA-California Only

This product contains a CR Coin Cell Lithium
Battery which contains Perchlorate Material
– special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate

When the equipment is installed in a cabinet or on
a shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or
more on both sides, on top and at the rear).
Do not block the ventilation holes.
(If the ventilation holes are blocked by a
newspaper, or cloth etc. the heat may not be able
to get out.)
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
When discarding batteries, environmental
problems must be considered and the local rules or
laws governing the disposal of these batteries must
be followed strictly.
The apparatus shall not be exposed to dripping or
splashing.
Do not use this equipment in a bathroom or places
with water.
Also do not place any containers filled with water
or liquids (such as cosmetics or medicines, flower
vases, potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this
equipment, fire or electric shock may be caused.)

Do not point the lens directly into the sun. This
can cause eye injuries, as well as lead to the
malfunctioning of internal circuitry. There is also a
risk of fire or electric shock.

CAUTION!

The following notes concern possible physical
damage to this unit and to the user.
Carrying or holding this unit by the LCD monitor
can result in dropping the unit, or in a malfunction.
Do not use a tripod on unsteady or unlevel surfaces.
It could tip over, causing serious damage to the unit.

CAUTION!

Connecting cables (Audio/Video, etc.) to

this unit
and leaving it on top of the TV is not recommended,
as tripping on the cables will cause

this unit

to fall,

resulting in damage.

CAUTION:

The mains plug shall remain readily operable.

•

Remove the mains plug immediately if the
camcorder functions abnormally.

WARNING:

The battery pack, the camcorder with battery
installed, and the remote control with battery
installed should not be exposed to excessive heat
such as direct sunlight, fire or the like.

CAUTION:

To maintain compliance with FCC’s RF exposure
guidelines, use only the supplied antenna.
Unauthorized antenna, modification, or attachments
could damage the transmitter and may violate FCC
regulations.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) This device must accept any interference
received, including interference that may Cause
undesired operation.

Make a backup of important recorded data

JVC will not be responsible for any lost data.
It is recommended to copy your important recorded
data to a disc or other recording media for storage
once every 3 months.

.

2

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifi ers) that produce heat.

9. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

10. Only use attachments/accessories specifi ed by
the manufacturer.

11. Use only with the cart,
stand, tripod, bracket,
or table specifi ed by
the manufacturer, or
sold with the apparatus.
When a cart is used,
use caution when
moving the cart/
apparatus combination
to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or
when unused for long periods of time.

13. Refer all servicing to qualifi ed service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

If this symbol is shown, it is only valid
in the European Union.

Remember that this unit is intended for
private consumer use only.

Any commercial use without proper permission
is prohibited. (Even if you record an event such
as a show, performance or exhibition for personal
enjoyment, it is strongly recommended that you
obtain permission beforehand.)

Trademarks

When using the AC adapter in areas other
than the USA

The provided AC adapter features automatic
voltage selection in the AC range from 110 V to 240 V.

USING HOUSEHOLD AC PLUG ADAPTER

In case of connecting the unit’s power cord to
an AC wall outlet other than American National
Standard C73 series type use an AC plug
adapter, called a “Siemens Plug”, as shown.
For this AC plug adapter, consult your nearest
JVC dealer.

Plug Adapter

Remove the AC adapter from the AC wall outlet
when not in use.
Do not leave dust or metal objects adhered to
the AC wall outlet or AC adapter (power/DC plug).

•

•

Be sure to use the supplied AC adapter.
Do not use the supplied AC adapter with other

devices.

•

•

This product is licensed under the AVC Patent
Portfolio License for the personal use of a
consumer or other uses in which it does not receive
remuneration to
(i) encode video in compliance with the AVC
standard (“AVC Video”) and/or
(ii) decode AVC Video that was encoded by a
consumer engaged in a personal activity and/or
was obtained from a video provider licensed to
provide AVC Video. No license is granted or shall
be implied for any other use. Additional information
may be obtained from MPEG LA, L.L.C.
See http://www.mpegla.com

•

AVCHD and AVCHD logo are trademarks

of Panasonic Corporation and Sony Corporation.

•

HDMI (High-Definition Multimedia Interface) and
HDMI logo are either registered trademarks or
trademarks of HDMI Licensing, LLC in the
United States and/or other
countries.

•

Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol

are trademarks of Dolby Laboratories.

•

SDXC logo is a trademark of SD-3C, LLC.

•

Windows® is either registered trademark or
trademark of Microsoft Corporation in the
United States and/or other countries.

•

Macintosh is a registered trademark of Apple Inc.

•

iMovie and iPhoto are trademarks of Apple Inc.,
registered in the U.S. and other countries.

•

The iFrame logo and iFrame symbol are
trademarks of Apple Inc.

•

YouTube™ and the YouTube logo are
trademarks and/or registered trademarks of
Google Inc.

•

Intel, Intel Core, and Pentium are trademarks or
registered trademarks of Intel Corporation or its
subsidiaries in the United States and other countries.

•

Android

™ is a trademark of Google Inc.

•

Wi-Fi, Wi-Fi logo, Wi-Fi CERTIFIED, Wi-Fi
CERTIFIED logo, Wi-Fi Protected Setup, Wi-Fi
Protected Setup logo, WPA, and WPA2 are
trademarks or registered trademarks of Wi-Fi Alliance.

•

Other product and company names included in
this instruction manual are trademarks and/or
registered trademarks of their respective holders.

•

Marks such as ™ and ® have been omitted in this
manual.

.

3

Contents

Safety Precautions ................................. 2

Available Accessories For the Camera .. 4

Getting Started

Charging the Battery Pack ..................... 5

Inserting an SD Card .............................. 6

Using the Icon Buttons/Thumbnails ........ 6

Changing Menu Settings ........................ 7

Clock Setting .......................................... 7

Recording

Video Recording .................................... 8

Still Image Recording ............................. 9

Playback

Playing Back/Deleting Files on this Unit

Playing Back on TV .............................. 10

Copying

Keep It High Definition (Windows) ....... 11

Install LoiLoFit for Everio (Windows) .... 12

USB Menu Operations ......................... 13

File Backup (Windows) ........................ 14

View Your Video (Windows) ................. 14

AVCHD Disc Creation (Windows) ........ 15

How to Upload a File (Video Clip) to

YouTube (Windows) ............................ 15

Record to a DVD or VHS Recorder ...... 16

Working with iMovie and iPhoto ........... 17

Simple File Backup with a Mac ............ 17

Further Information

Troubleshooting/Cautions .................... 18

.... 9

Recordable Time/Specifications .......... 20

Available Accessories For the Camera

Product Name* Description

Battery Pack

BN-VG114U

0

BN-VG121U

0

Battery Charger

AA-VG1U

0

*

To order any of these accessories please visit www.store.jvc.com or call 1-800-252-5722

Provides a longer recording time than the battery pack that

0

comes with this unit or it can also be used as a spare battery
pack.

Enables the battery pack to be charged without using this unit.

0

4

Charging the Battery Pack

P

OWER/

POWER/

CHARG

E

CHARGE

CESS

CESS

(Base)

To detach the battery pack

Charging finished:
Goes out

Charging in progress:
Blinks

Charging Lamp

Plug in the power.

(110 V to 240 V)

AC Adapter
To AC Outlet

Cover

Connect the DC
connector.

Mark

Align the top of the battery
with the mark on this unit,
and slide in until the battery
clicks into place.

The battery pack is not
charged at the time of
purchase.

Attach the battery pack.

.

CAUTION

Be sure to use JVC battery packs.

If you use any other battery packs besides JVC battery packs, safety and

0

performance cannot be guaranteed.
If malfunctions (overcurrent, overvoltage, transmission error, etc) occur, or if any

0

battery manufactured other than JVC is attempted for battery charge, charging
stops. In these cases, the CHARGE lamp blinks quickly for notification.
You can record or play back videos while the AC adapter is connected. (Battery

0

charging cannot be performed during recording or playback.)
Remove the battery when the unit is to be used for a long time. Performance
of the battery may drop if it is left attached to the unit.
Charging time: Approx. 2 h 30 m (using supplied battery pack)

0

The charging time is when the unit is used at 25°C (77°F). If the battery pack is

0

charged outside the room temperature range of 10°C to 35°C (50°F to 95°F),
charging may take a longer time or it may not start. CHARGE lamp blinks 2 times
in a slow cycle for notification if the battery charge does not start. Also, please
note that the recordable and playable time may be shortened under some usage
conditions, such as at low temperature.

5

Inserting an SD Card

Turn off the power of this unit before
inserting or removing an SD card.

(Base)

Label

Insert an SD card.

Open the cover.

Close the LCD monitor.

≪REC

PLAY

0:01:23 0:12:34

Index ScreenPlayback ScreenRecording Screen

MENU

≪PLAY

REC

0:01:23 0:12:34

MENU

≪REC

Insert a commercially available SD card before recording.

.

To remove the SD card

o

Push the SD card inward once, then pull it out straight.

NOTE

Operations are confirmed on the following SD cards.

Manufacturer Panasonic, TOSHIBA, SanDisk
Video A

Still Image B

Using SD cards (including SDHC/SDXC cards) other than those specified

0

above may result in recording failure or data loss.
This unit is not guaranteed to operate with all SD cards, even when using the ones

0

specified above. Some SD cards may not work due to specification changes, etc.
To protect the data, do not touch the terminals of the SD card.

0

When using an SDXC card, check its compatibility with the OS of your computer

0

by referring to the Detailed User Guide.

Class 4 or higher compatible SD card (2 GB)/
Class 4 or higher compatible SDHC card (4 GB to 32 GB)/
Class 4 or higher compatible SDXC card (48 GB to 128 GB)

When recording with video quality [UXP], Class 6 or higher is

0

recommended.
When recording with iFrame format, Class 6 or higher is required.

0

SD card (256 MB to 2 GB) / SDHC card (4 GB to 32 GB) /
SDXC card (48 GB to 128 GB)

Using the Icon Buttons/Thumbnails

A

Tap the displayed button (icon) or thumbnail (file) on the touch screen to make selection.

B Drag the thumbnails on the touch screen to search for the desired file.

.

6

Changing Menu Settings

REC

≪PLAY

MENU

NO

YES

SET DATE/TIME!

AM

201324 10 00

TIMEDATE

CLOCK SETTING

DEC

SET

To change camera settings, tap [MENU] and
select the item which you want to change.

Tap [MENU].

1

.

Tap the desired item in the menu.

2

.

0

Tap F to display “shortcut menu”.

Clock Setting

Open the LCD monitor.

1

Tap the desired item to change the

3

settings.

(Icon type screen)

.

0

Tap 0 or 1 to scroll the screen.

0

Tap 3 or 2 to scroll the screen.

To exit the screen

o

Tap L (quit).

To return to the previous screen

o

Tap J (return).

3

(List type screen)

.

Set the date and time.

.

The unit turns on. When the LCD

0

monitor is closed, the unit turns off.

Tap [YES] when [SET DATE/TIME!]

2

is displayed.

.

.

When the year, month, day, hour, or minute

0

item is tapped, 3 and 2 will be displayed.
Tap 3 or 2 to adjust the value.

Repeat this step to input the year, month, day,

0

hour, and minute.

After setting the date and time, tap [SET].

4

Select the region where you live and

5

tap [SAVE].

Time difference between the selected

0

city and the GMT (Greenwich Mean
Time) is displayed.

0

Tap 0 or 1 to select the city name.

7

Video Recording

H

P

A

C

A

(Wide angle)

Zooming

Open the
lens cover.

Check if the recording
mode is C Intelligent Auto.

Start recording.

Press again to stop.

(Telephoto)

If the mode is H Manual, tap

H on the touch screen, then

tap P to switch.

If the mode is B still image,
tap B on the touch screen,
then tap A to switch.

Check if the recording
mode is A video.

MENU

≪PLAY

0:00:00 [0:54]

REC

Recording in Progress

Recording-Standby

Battery Indicator

Recording Media

Image Stabilizer

Video Quality

Remaining Recording Time

Scene Counter

You can record without worrying about the setting details by using the Intelligent Auto mode. Settings
such as exposure and focus will be adjusted automatically to suit the shooting conditions.

In case of specific shooting scenes such as person etc., its icon is displayed on the screen.

0

Before recording an important scene, it is recommended to conduct a trial recording.

0

The mode can also be switched between video and still image by pressing the A/B

.

button on this unit.
You can also tap

0

6

on the touch screen to record. To stop recording, tap

In addition, you can also tap D to zoom.

0

You can tap D to tag important scenes while recording so that those scenes can be
found easily and watched instantly.

Indications during video recording

o

NOTE

The estimated recording time of the supplied battery pack is approx. 1 hour 5

0

minutes.
Do not remove the battery pack, AC adapter, or SD card when the access lamp

0

is lighted. The recorded data may become unreadable.
This unit turns itself off automatically to conserve power when it is not operated

0

for 5 minutes. (only when using the battery pack)
The angle of view may change when the image stabilizer is turned on or off.

0

8

.

7

.

Still Image Recording

Press halfway

If the mode is A
video, tap A on the
touch screen, then
tap B to switch.

Check if the
recording mode
is B still image.

Set the focus on the subject.

Press fully

Lights up in green when
focused

Lights up during still
image recording

Take a still image.

≪REC

PLAY

A delete mark appears on
the selected file. To remove
the delete mark, tap again.

Ta p F on the touch screen to select
the playback mode.

Ta p E to return to the recording mode.

Tap on the file to play back.

Ta p e to pause playback.
Ta p u to return to the index screen.

Volume adjustment during playback

Turn down the

volume

Turn up the volume

To delete unwanted files

Ta p A.
Tap on the files to delete.

Tap [EXECUTE] when the confirmation
message appears.
Tap [OK].

Ta p A or B to select the video or still
image mode.

DELETE

SEL ALL

REL ALL

SET QUIT

Tap [SET].

.

0

You can also tap Q on the touch screen to record. However, focus cannot be set by pressing halfway.

Playing Back/Deleting Files on this Unit

Select and play back the recorded videos or still images from an index screen (thumbnail display).

.

To capture a still image during playback

o

Pause the playback and press the SNAPSHOT button.

NOTE

While this unit may be used with the LCD monitor reversed and closed, the

0

temperature rises more easily. Leave the LCD monitor open when using this unit.
The power may turn off to protect the circuit if the temperature of this unit rises too much.

0

9

Playing Back on TV

HDMI Connector
Input

TV

HDMI Cable
(Optional)

To HDMI Mini

Connector

Red

White

Ye l l o w

TV

Audio Input (R)

Audio Input (L)

Video Input

Video Input

AV Cable (Provided)

To AV Connector

Preparation:

Turn off both camera and TV.

0

To connect using the HDMI mini connector

When connecting to a 1080p compatible TV, set [HDMI OUTPUT] in [CONNECTION
SETTINGS] to [AUTO].

.

NOTE

Use a High Speed HDMI mini cable.

0

To connect using the AV connector

Change the settings of [VIDEO OUTPUT] in [CONNECTION SETTINGS] according to
the connection.

.

Playback Operation

After the connection with TV is completed

Turn on the camera and the TV.

A

This unit powers on automatically when the AC adapter is connected.

0

Select the TV input switch.

B

Start playback on the camera.

C

10

Keep It High Definition (Windows)

Back up to a computer:

o

The provided JVC software also makes it easy to copy your videos to a computer.

For customers with a Blu-ray Player:

o

The provided JVC software lets you create high definition AVCHD discs using standard blank
DVD-R media, and your Windows computer with DVD Burner.
An AVCHD disc is a great choice because it contains the original HD video, which can be
stored on inexpensive blank DVD-R media.
These discs can be played back in virtually any recent Blu-ray player that has the AVCHD logo.

Upload to YouTube

YouTube is a great way to share your videos, in either HD or SD quality. JVC makes it easy.

Copying Files

You can create discs or copy the files on this unit by connecting it to various devices.

Recordable and playable

:

I

Playable only

:

F

Not applicable

:

—

Standard

Quality

HD Quality

Media Selection

Blu-ray Recorder

.

DVD Recorder

.

Device

.

Computer

.

VCR

.

(VHS

Tape)

—

—

I

—

.

.

(DVD

Disc)

(DVD

Disc)

.

(Blu-ray

Disc)

I

*4F*1, *4I*1, *4I*4

I

*4F*1, *4

—

— — — —

I

I

*2

I

*3

.

(Device’s

internal

HDD)

I

*4

I

Page

See Detailed User
Guide and manual

of recorder.

See Detailed User
Guide and manual

of recorder.

See Detailed User
Guide and manual

of recorder.

p. 14

*1 Only on AVCHD compatible devices.
*2 For details on how to create a disc using a computer, refer to the Detailed User Guide.
*3 Blu-ray discs cannot be created using the provided software. To create Blu-ray discs,

use a commercially available software.

*4 Videos recorded in iFrame mode are not supported.

Each of these solutions is explained in detail in the following sections.

11

Install LoiLoFit for Everio (Windows)

11

LoiLoFit for Everio is included with your
camera. It lets you archive and organize
your videos. It also lets you create discs and
upload video to YouTube, and other
popular web sites.

Load the provided CD-ROM into your

1

computer.

In Windows Vista / Windows 7, the auto

0

play dialog box appears.

Click “LoiLoFit for Everio”.

2

.

Follow the on-screen instructions.

0

“Windows installer” appears after a

0

while. If it doesn't appear, double-click
the CD-ROM icon in “My Computer”.

Installation ends and an icon is

3

created on the desktop.

LoiLoFit for Everio uses a calendar based
interface that makes it easy to find any
video you have recorded by selecting the
appropriate date.

.

NOTE

In order to start the supplied

0

software, activation (licensing
verification) is required. Perform
the activation by following
instructions on the screen.

.

Click “Quit” on the setup screen.

4

12

USB Menu Operations

CONNECT TO PC

TYPE TO CONNECT

SELECT DEVICE

SELECT DEVICE

PLAYBACK ON PC

CONNECT TO PC

By connecting a USB cable between this
unit and your computer, you can perform
operations such as file backups to
computer/disc or file uploads to file-sharing
site using your computer.

Preparation:

Install the LoiLoFit for Everio software

0

onto the computer.
Close the LCD monitor to turn off the

0

camera. Disconnect the power supply.

Open the LCD monitor to connect
to the computer with the USB

1

cable.

Refer to the connection diagram in the

0

“File Backup (Windows)” section.
(p. 14)
Reconnect the power supply to turn on

0

the camera.

The [SELECT DEVICE] menu appears.
Tap [CONNECT TO PC] on the camera’s

2

touch screen.

.

Tap [CONNECT TO OTHER] if the camera

0

is connected to a device other than a
computer.

The [CONNECT TO PC] menu appears.

3

Tap an option that best suits your needs.

.

Option Usage

PLAYBACK
ON PC

CREATE
DISC

DIRECT
DISC

UPLOAD

BACK UP0To back up recordings on

For detailed operations on the above options,
refer to the other sections in this guide or the
“Detailed User Guide”.

To play back your recordings

0

on the computer.
To back up your recordings

0

on the computer without
using the provided software.

To save your recordings on a

0

disc.
To save all unsaved

0

recordings on a disc.
To upload videos to file-

0

sharing sites.

the computer.

13

File Backup (Windows)

To USB Connector

To AC Outlet
(110 V to 240 V)

AC Adapter

USB Cable
(Provided)

To DC

Connector

To USB
Connector

BACK UP

CONNECT TO PC

1

Click Click

㧺㨑㨤㨠

Click

Click

1

Preparation:

Install the LoiLoFit for Everio software

0

onto the computer.
Make sure that enough space is left in the

0

HDD of computer.
Close the LCD monitor to turn off the

0

camera. Disconnect the power supply.

Open the LCD monitor to connect to

1

the computer with the USB cable.

.

Reconnect the power supply to turn on

0

the camera.

On the camera:

o

Tap [CONNECT TO PC] on the

2

camera’s touch screen.

Tap [BACK UP] on the camera’s

3

touch screen.

.

LoiLoFit for Everio starts on the

0

computer.

On the computer:

o

Select files to backup.

4

.

Start backup.

5

.

NOTE

File backup is only supported by

0

the provided software.

View Your Video (Windows)

14

On the Home screen

To view the video on your camera, click on the Media Select Tab>Everio.

0

To view video that has already been archived to the computer, click

0

on the Media Select Tab>PC and then choose the date the video was
recorded.

NOTE

Choose File/Option Settings on the Menu Bar to see the folder where

0

LoiLoFit for Everio stores your videos. You can also play back your
videos from this folder in most popular media players.

AVCHD Disc Creation (Windows)

LoiLoFit for Everio makes it possible to

0

create AVCHD discs to archive your
recordings in their original high definition
quality.
You can use any standard DVD-R or

0

DVD-RW disc.
A standard 4.7 GB disc will hold

0

approximately 35 minutes of video in the
highest quality setting.
AVCHD discs can be played back in any

0

Blu-ray player that is AVCHD compatible.
Just look for the AVCHD logo.

.

NOTE

For details on how to create a disc by computer, refer to the help page of the

0

provided software.

Preparation:

Install the software on your computer.

0

Click on the “Disk” button.

1

.

Select “AVCHD Disk” from the Disk

2

menu.

Select the video clips you wish to

3

include.

Arrange the video clips in the order

4

in which you want to view them.

Create the AVCHD disc.

5

How to Upload a File (Video Clip) to YouTube (Windows)

Uploading Videos

You can upload your videos to YouTube
using the provided software “LoiLoFit for
Everio”.

Preparation:

Install the software on your computer.

0

Click on the “Upload” button.

1

.

Select “YouTube” from the Upload

2

menu.

Select the video clips you wish to

3

include.

Enter account and upload

4

information.

Start upload to YouTube.

5

Trouble with Uploading Videos

o

Check if you have created an account

0

with YouTube.

Trouble with Using the Provided

o

Software “LoiLoFit for Everio”

Consult the customer service center

0

below.

http://loilo.tv/us/product/LoiLoFit_for_Everio

15

Record to a DVD or VHS Recorder

Audio Input (R)

Audio Input (L)

Video Input

Video Input

Red

White

Ye l l o w

To DC Connector

To AC Outlet
(110 V to 240 V)

AC Adapter

AV Cable (Provided)

To AV Connector

DVD/VHS Recorder

It is also possible to record to a DVD or VHS recorder. Please note that this will create a
standard definition recording with standard definition picture quality.

.

Preparation:

Use the supplied AV cable. The yellow connection is video. The white connection is left

0

channel audio. The red connection is right channel audio. Connect this cable to the AV
input on your DVD or VHS recorder.
Follow your DVD/VHS recorder instructions to copy (dub) the video.

0

16

Working with iMovie and iPhoto

USB cable
(Provided)

To USB
port

To USB
Connector

USB cable
(Provided)

To USB
port

To USB
Connector

PLAYBACK ON PC

CONNECT TO PC

You may use the software supplied with

0

the Mac Computer to view and edit files
from the Camera.
Connect the Camera to the Mac

0

Computer using a USB Cable.

iMovie and iPhoto

o

You can import files from this unit to a
computer using Apple’s iMovie ’08, ’09
or ’11 (video) or iPhoto (still image).
To verify the system requirements, select
“About This Mac” from the Apple menu. You
can determine the operating system
version, processor and amount of memory.

NOTE

.

NOTE

Files must be transferred to the

0

Mac Computer for editing.

For the latest information on iMovie

0

or iPhoto, refer to the Apple website.
For details on how to use iMovie or

0

iPhoto, refer to the help file of the
software.
There is no guarantee that the

0

operations will work with all
computer environments.

Simple File Backup with a Mac

Preparation:

Make sure that enough space is left in the

0

Mac’s HDD.
Close the LCD monitor to turn off the

0

camera. Disconnect the power supply.

Open the LCD monitor to connect
to the computer with the USB

1

cable.

Tap [CONNECT TO PC] on the

2

camera’s touch screen.

Tap [PLAYBACK ON PC] on the

3

camera’s touch screen.

.

Reconnect the power supply to turn on

0

the camera.

.

Copy and paste the files to the Mac

4

Computer for backup.

17

Troubleshooting/Cautions

Battery Pack

Troubleshooting

The supplied battery pack is a
lithium-ion battery. Before using
the supplied battery pack or an
optional battery pack, be sure
to read the following cautions:

Terminals

•

To avoid hazards

...

do not burn.
do not short-circuit the terminals. Keep it away

from metallic objects when not in use. When
transporting, carry the battery in a plastic bag.

do not modify or disassemble.
do not expose the battery to temperatures

exceeding 60°C (140°F), as this may cause the
battery to overheat, explode or catch fire.
use only specified chargers.

...

...
...

...

...
...

...

...

...

...

•

To prevent damage and prolong service life

do not subject to unnecessary shock.
charge within the temperature range of 10°C
to 35°C (50°F to 95°F). Cooler temperatures
require longer charging time, or in some cases
stop charging at all.
Warmer temperatures prevent complete
charging, or in some cases stop charging at all.
store in a cool, dry place. Extended exposure
to high temperatures will increase natural
discharge and shorten service life.

keep a 30% battery level (X) if the battery pack
is not to be used for a long period of time.
In addition, fully charge and then fully discharge
the battery pack every 6 months, then continue
to store it at a 30% battery level (

X).

remove from charger or powered unit when not
in use, as some machines use current even
when switched off.
do not drop or subject to strong impact.

While the LCD monitor screen has more than

99.99% effective pixels, 0.01% of the pixels
may be bright spots (red, blue, green) or dark
spots. This is not a malfunction. The spots will
not be recorded.

ATTENTION:

The product you have purchased
is powered by a rechargeable
battery that is recyclable.
Please call 1-800-8-BATTERY for
information on how to recycle this
battery.
(USA and Canada only)

Recording Medium

•

Be sure to follow the guidelines below

to prevent corruption or damage to your

recorded data.

•

Do not bend or drop the recording medium,

or subject it to strong pressure, jolts or
vibrations.

•

Do not splash the recording medium with water.

•

Do not use, replace, or store the recording

medium in locations that are exposed to
strong static electricity or electrical noise.

•

Do not turn off the camcorder power or

remove the battery or AC adapter during
shooting, playback, or when otherwise
accessing the recording medium.

•

Do not bring the recording medium near

objects that have a strong magnetic field or
that emit strong electromagnetic waves.

•

Do not store the recording medium in locations

with high temperature or high humidity.

•

Do not touch the metal parts.

•

When formatting or erasing data using
the camcorder, only the file administration
information is changed. The data is not
completely erased from the recording medium.
If you want to completely erase all of the data,
we recommend either using commercially
available software that is specially designed
for that purpose, or by physically destroying
the camcorder with a hammer etc.

LCD Monitor

•

To prevent damage to the LCD monitor,

DO NOT

... push it strongly or apply any shocks.
... place the camcorder with LCD monitor on the

bottom.

•

To prolong service life

... avoid rubbing it with coarse cloth.

If the above do not solve the problem, consult
your nearest JVC dealer or JVC service center.

Remove the AC adapter and battery pack from
this unit, reattach them, open the LCD monitor
and this unit powers on automatically.

Turn off the power. (Close the LCD monitor.)

In such a case, reset the unit.

This unit is a microcomputer-controlled device.
Electrostatic discharge, external noise and
interference (from a TV, a radio, etc.) might
prevent it from functioning properly.

If you have difficulties operating the unit, refer
to the detailed descriptions in the “Detailed
User Guide”.

Refer to the “Troubleshooting” section in the
“Detailed User Guide”.

If you encounter problems with this unit, check the
following before requesting service.

http://manual3.jvckenwood.com/index.html/

1.

A
B

2.

3.

.

18