JVC GVT0291-002B, XS-SR 3 User Manual

ENGLISH

SPEAKER SYSTEM

XS-SR3

Thank you for purchasing a JVC product.

For customer use:

Enter below the Model No. and Serial No. which are located either on the rear, bottom or side of the cabinet. Retain this information for future reference.

Model No.

Serial No.

Warnings, Cautions and Others / Mises en garde, précautions et indications diverses

For U.S.A. Caution: Changes or modifications not expressly approved by party responsible

for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

–

Increase the separation between the equipment and receiver.

–

Connect the equipment into an outlet on a circuit different from that to which

–

the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

–

INSTRUCTIONS

Pour les Etats-Unis Attention : Les changements ou les modifications qui ne sont pas explicitement

approuvés par la partie responsable de l’observance pourraient mettre fin au droit de l’utilisateur d’utiliser le matériel. Remarque : Cet appareil a été testé et il s’est avéré conforme aux limites applicables à un appareil numérique de classe B, en vertu de la Partie 15 des Règles de la FCC. Ces limites sont conçues de manière à assurer une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet appareil produit, utilise et peut émettre une énergie de haute fréquence et, s’il n’est pas installé et utilisé en conformité avec les instructions, il peut causer des interférences nuisibles aux communications radio. Il n’y a, toutefois, aucune garantie que des interférences ne se produiront pas dans une installation particulière. Si cet appareil cause effectivement des interférences nuisibles à la réception de la radio ou de la télévision, ce qu’on peut établir en mettant l’appareil en marche et à l’arrêt, nous encourageons l’utilisateur à tenter de corriger l’interférence par une ou plusieurs des mesures suivantes :

réorienter ou déplacer l’antenne de réception ;

–

accroître la séparation entre l’appareil et le récepteur ;

–

brancher l’appareil dans une prise ou un circuit autre que celui auquel le

–

récepteur est branché ; consulter un vendeur ou un technicien radio/TV expérimenté pour obtenir

–

de l’aide.

WARNING

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

AVERTISSEMENT

POUR PRÉVENIR LES RISQUES D’INCENDIE OU DE CHOCS ÉLECTRIQUES, NE PAS EXPOSER CE APPAREIL À LA PLUIE OU À L’HUMIDITÉ.

For Canada

THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.

Pour le Canada

CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR LE MATERIEL BROUILLEUR; “APPAREILS NUMERIQUES”, NMB-003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.

CAUTION

Battery shall not be exposed to excessive heat such as sunshine, fire or the like.

ATTENTION

Les piles ne doivent en aucun cas être exposées à une chaleur excessive (lumière du soleil, feu, etc.).

CAUTION

The

button in any position does not disconnect the mains line. Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

•

When the System is on standby, the STANDBY lamp lights red.

•

When the System is turned on, the STANDBY lamp turns green.

The power can be remote controlled.

ATTENTION

La touche système du secteur. Déconnectez la fiche de secteur pour mettre l’appareil complètement hors tension (le témoin STANDBY s’éteint). La fiche secteur ou un coupleur est utilisé comme dispositif de déconnexion de l’appareil, et l’appareil déconnecté doit être prêt à être utilisé.

•

• L’alimentation peut être télécommandée.

CAUTION

•

ATTENTION

•

, dans n’importe quelle position, ne déconnecte pas le

Quand le système est en attente, le témoin STANDBY est allumé en rouge. Quand l’appareil est sous tension, le témoin STANDBY est allumé en vert.

Do not block the ventilation openings or holes. (If the ventilation openings or holes are blocked by a newspaper or cloth, etc., the heat may not be able to get out.) Do not place any naked flame sources, such as lighted candles, on the apparatus. When discarding batteries, environmental problems must be considered and local rules or laws governing the disposal of these batteries must be followed strictly. Do not expose this apparatus to rain, moisture, dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Ne bloquez pas les orifices ou les trous de ventilation. (Si les orifices ou les trous de ventilation sont bloqués par un journal un tissu, etc., la chaleur peut ne pas être évacuée correctement de l’appareil.) Ne placez aucune source de flamme nue, telle qu’une bougie, sur l’appareil. Lors de la mise au rebut des piles, veuillez prendre en considération les problèmes de l’environnement et suivre strictement les règles et les lois locales sur la mise au rebut des piles. N’exposez pas cet appareil à la pluie, à l’humidité, à un égouttement ou à des éclaboussures et ne placez pas des objets remplis de liquide, tels qu’un vase, sur l’appareil.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. “Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. iPod is a trademark of Apple Inc., registered in the U.S. and other countries.

CAUTION

To reduce the risk of electrical shocks, fire, etc.:

Do not remove screws, covers or cabinet.

1. Do not expose this appliance to rain or moisture.

ATTENTION

Afin d’éviter tout risque d’électrocution, d’incendie, etc.:

Ne pas enlever les vis ni les panneaux et ne pas ouvrir le coffret de l’appareil.

Ne pas exposer l’appareil à la pluie ni à l’humidité.

Rating label is placed on the exterior of the bottom.

L’étiquette des caractéristiques nominales se trouve sur l’extérieur du coffret.

[European Union only] [Union européenne seulement]

Specifications

Output power:

2.5 W per channel, RMS at 4 Ω at 1 kHz, with 10% total harmonic distortion

Speaker Type: Full-Range Bass-Reflex Type (Magnetically-Shielded Type) Speaker: 4 cm (1-5/8”) cone × 2 Speaker Impedance: 4 Ω Analog Input (ANALOG IN): 125 mV/50 kΩ Digital Input (DIGITAL IN): –21 dBm to –15 dBm (660 nm ±30 nm) iPod Dock Output: DC 5 V 500 mA Power Source: DC 6 V 1 A (DC IN) AC Adaptor (AA-R607)

INPUT: AC 100 V – 240 V , 50 Hz/60 Hz, 1.0 A

• OUTPUT: DC 6 V 1 A

•

Dimensions (W × H × D): 390 mm × 103 mm × 136 mm (15-3/8” × 4-1/16” × 5-3/8”) Mass: 0.55 kg (1.3 lbs)

Accessories

Remote control (× 1)

• Lithium coin battery CR2025 (× 1); Installed in the remote control when

• shipped. AC adaptor (AA-R607) (× 1)

• AC power cord (× 1)

• Core filter (× 1)

• Brackets for iPod (× 3)

•

Precautions

Install the System on a place which is level, dry, and neither too hot nor too

• cold; between 5°C and 35°C (41°F and 95°F). Do not use the System in a location near heat sources, or in a place subject to

• direct sunlight, excessive dust, or vibration. Leave sufficient distance between the System and the TV.

• Do not insert any metallic objects or liquids into the System.

• Do not handle the power cord with wet hands.

• A small amount of power is always consumed while the power cord is

• connected to the wall outlet. Do not pull on the cord to unplug the power cord. When unplugging the

• power cord, always grasp and pull the plug so as not to damage the cord. There are no user-serviceable parts inside. If anything goes wrong, unplug the

• power cord and consult your dealer. When away on holiday or for other reasons for an extended period of time,

• disconnect the power cord from the wall outlet. Stains on the System should be wiped off with a soft cloth. If the System is

• heavily stained, wipe it with a cloth soaked in water diluted neutral detergent and wrung well, then wipe clean with a dry cloth.

Connection

2-channel digital audio sources*

To the wall outlet

AC power cord (supplied)

CAUTION

DO NOT connect the power cord until all other connections have been made.

•

To avoid the risk of fire and to prevent damage,

•

Do not use any AC adaptors other than the one supplied.

–

Do not use the supplied AC adaptor for other equipment.

–

AC adaptor (supplied)

Using the core filter

Attach the provided core filter to the power cord to reduce interference.

1 Release the stopper of the

core filter.

2 Run the cable through the core filter, and wind the

cable firmly once inside the cutout of the core filter as shown in the illustration.

Power cord

5 cm (2 inches)

3 Close the core filter until it clicks shut.

CAUTION

Do not damage the cord by applying excessive force when winding.

Stopper

If water gets inside the System, turn the power off and disconnect the power

• cord from the wall outlet, then call the store where you purchased this System. Using the System in this condition may cause a fire or electrical shock. Since the System may deteriorate in quality, become damaged or get its paint

• peeled off, be careful about the following:

DO NOT wipe it forcefully.

–

DO NOT wipe it with thinners, benzines or other organic solvents including

–

disinfectants. DO NOT apply any volatile substances such as insecticides to it.

–

DO NOT allow any rubber or plastic to remain in contact with it for a long

–

time.

About the built-in speakers

The speakers are magnetically shielded to avoid color distortions on TVs. If the color on a TV is distorted, perform the following procedure:

Turn off the TV’s main power switch or unplug it before installing the System.

–

Then wait at least 30 minutes before turning on the TV’s main power switch again.

Some TVs may still be affected even though you have followed the above procedure. If this happens, move the System away from the TV.

Digital optical cable (not supplied)Digital output of an audio player for playing

Stereo mini plug cable (not supplied)

Analog output of an audio player

* Compatible signal: 2-channel linear PCM (32 kHz, 44.1 kHz, and 48 kHz

sampling frequency). No multi-channel signal is playable.

Preparing the remote control

When using the remote control for the first time, pull out the insulation sheet.

To replace the battery, be sure to insert the

• battery into the remote control by matching the polarities (+ and –) correctly. If the range or effectiveness of the remote control

• decreases, replace the battery.

For USA-California Only

This product contains a CR Coin Cell Lithium Battery which contains Perchlorate material—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

CAUTION

Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

WARNINGS

Store the battery in a place where children cannot reach. If a child accidentally

•

swallows the battery, consult a doctor immediately. Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.

•

Doing any of these things may cause the battery to give off heat, crack, or start a fire. Do not leave the battery with other metallic materials. Doing this may cause the

•

battery to give off heat, crack, or start a fire.

Lithium coin battery (product number: CR2025)

When throwing away or saving the battery, wrap it in tape and insulate;

•

otherwise, the battery may start to give off heat, crack, or start a fire. Do not poke the battery with tweezers or similar tools. Doing this may cause the

•

battery to give off heat, crack, or start a fire. Dispose of battery in the proper manner, according to federal, state, and local

•

regulations.

Basic Operation

Press to turn on the power.

The standby lamp turns green.

2 Press AUDIO IN DIGITAL,

AUDIO IN ANALOG, or iPod 6 to

select the source.

iPod starts playing back. Go to step 4. For other equipment, go to step 3.

3 Start playing back the

connected equipment.

4 Press VOL +/– to adjust the

volume.

To turn off the sound temporarily, press

• FADE MUTING.

To restore the sound, press the button again or

–

adjust the volume.

To turn off the operation sounds, press

• BEEP SOUND.

CAUTION

Set the volume to the minimum level before starting playback. If the volume is set to a high level, the sudden blast of sound may damage your hearing and

Remote sensor

blow out the speakers.

Enjoying Surround Mode

This System is equipped with Virtual Dolby Surround. In Surround Mode, it creates a rich surround sound effect with two speakers. To activate Surround Mode, press SURROUND MODE 1/2. Pressing the button beeps...

Once when SURROUND MODE 1 is selected, or

–

Twice when SURROUND MODE 2 is selected.

–

SURROUND MODE 1:• Creates a surround sound effect. SURROUND MODE 2:• Creates a richer surround sound effect than

To cancel, press SURROUND OFF.–

SURROUND MODE 1.

Operating iPod device

•

To select a track, press 4/¢.

•

For forward search/reverse search, press and hold 4/¢.

•

For Shuffle play, press SHUFFLE.

•

For Repeat play, press REPEAT.

•

To put iPod into sleep mode, press and hold iPod 6.

iPod menu operation

1 Press MENU to display the menu. 2 Press UP or DOWN, then SELECT to select a menu

item.

Refer also to the instruction manual for the iPod for details.

To go back to the previous menu, press MENU.

•

Rotating the dock

You can rotate the dock for iPod touch/iPod nano (4th Generation). To hold the iPod in place, attach the bracket (supplied) which fits your iPod to the dock.

Dock

Bracket for iPod (supplied)

Attach hook side down.•

NOTE

While inserted into the dock, the battery of iPod is always charged through the

•

System. Do not carry the System with iPod connected. You might drop the iPod or it

•

might cause damage to the iPod or the System. Do not touch or hit the iPod terminal pins or connector pins in the dock directly. It

•

might cause damage to the pins. Do not rotate the dock with excessive force.

•

Compatible iPod models

iPod nano 1GB/2GB/4GB iPod nano (2nd Generation)

2GB/4GB/8GB iPod nano (3rd Generation) 4GB/8GB iPod nano (4th Generation)

8GB/16GB iPod mini 4GB/6GB iPod mini (2nd Generation) 4GB/6GB iPod (4th Generation) 20GB/40GB

If iPod does not play correctly, update iPod software to the latest version.

For details about updating iPod, check on the Apple web site <http://www.

• apple.com>.

JVC does not assure the compatibility of iPod released after April

• 2009 with this System. JVC is not responsible for any loss of or damage to iPod that might

• result from the use of this product.

iPod classic 80GB/120GB/160GB iPod photo (4th Generation)

20GB/30GB/40GB/60GB

iPod video (5th Generation)

30GB/60GB/80GB iPod touch 8GB/16GB iPod touch (2nd Generation)

8GB/16GB/32GB

Troubleshooting

If you have a problem with this System, check this list for a possible solution before calling for service.

Power does not come on.

Plug in the power cord securely.

No sound comes out of the speakers.

Adjust the volume level.

The sound has been turned off temporarily. Press FADE MUTING.

The remote control does not work.

Pull out the insulation sheet.

Replace the battery if exhausted.

Avoid sunlight shining directly on the remote sensor.

Do not block the path between the remote control and the remote sensor

on the System. Point the remote control at the remote sensor on the System.

Move closer to the System.