JVC GR-SXM937UM User Manual

COMPACT VHS CAMCORDER

GR-SXM937UM

INSTRUCTIONS

ENGLISH

CONTENTS

SAFETY PRECAUTIONS QUICK OPERATION GUIDE MAJOR FEATURES PROVIDED ACCESSORIES

GETTING STARTED BASIC VIDEO RECORDING BASIC DIGITAL STILL CAMERA

(D.S.C.) SHOOTING RECORDING

Basic Features ................................. 23

Advanced Features ........................... 28

VIDEO PLAYBACK

Basic Playback ................................ 39

Features ........................................ 40

Using The Cassette Adapter ................ 4 1

BASIC CONNECTIONS

Basic Connections And Tape Dubbing ...... 42

D.S.C. PLAYBACK

Basic Playback ................................ 44

Connection ..................................... 45

Advanced Features ........................... 46

USING THE REMOTE CONTROL UNIT

Playback Zoom ................................ 53

Insert Editing (VIDEO) ....................... 54

Insert Editing (Inserting A Still Image From

The Built-in Memory Onto A Tape) ...... 55

Audio Dubbing ................................. 55

Animation And Time-Lapse .................. 56

TROUBLESHOOTING INDEX

Controls, Connectors And Indicators ....... 60

Indications ..................................... 6 2

USER MAINTENANCE CAUTIONS TERMS SPECIFICATIONS

2 – 5

6 – 7

10 – 17

18 – 19

20 – 22

23 – 38

39 – 41

42 – 43

44 – 51

52 – 56

57 – 59

60 – 63

65 – 67

68 – 69

70 – 71

LYT0493-001A

2 EN

Dear Customer,

Thank you for purchasing the JVC Compact VHS camcorder. Before use, please read the safety information and precautions contained in the following pages to ensure safe use of this product.

Using This Instruction Manual

•All major sections and subsections are listed in the Table Of Contents on the cover.

•Notes appear after most subsections. Be sure to read these as well.

•Basic and advanced features/operation are separated for easier reference.

It is recommended that you . . .

.... refer to the Index (Z pgs. 60 – 63) and familiarize yourself with button locations, etc. before use.

.... read thoroughly the Safety Precautions and Safety Instructions that follow. They contain extremely

important information regarding the safe use of this product.

You are recommended to carefully read the cautions on pages 65 – 67 before use.

SAFETY PRECAUTIONS

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

Caution on Replaceable lithium battery

The battery used in this device may present a fire or chemical burn hazard if mistreated. Do not recharge, disassemble, heat above 100°C or incinerate. Danger of explosion or Risk of fire if the battery is incorrectly replaced. Replace battery with Panasonic (Matsushita Electric), Sanyo, Sony or Maxell CR2025. Danger of explosion if the battery is incorrectly replaced.

n Dispose of used battery promptly. n Keep away from children. n Do not disassemble and do not dispose of in

fire.

CAUTIONS:

n To prevent shock, do not open the cabinet.

No user serviceable parts inside. Refer servicing to qualified personnel.

n When you are not using the AC Power

Adapter/Battery charger for a long period of time, it is recommended that you disconnect the power cord from AC outlet.

NOTES:

●

The rating plate (serial number plate) and safety caution are on the bottom and/or the back of the main unit.

●

The rating information and safety caution of the AC Power Adapter/Charger are on its bottom.

EN3

This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for playback with a television of a different standard. However, live recording and LCD monitor/viewfinder playback are possible anywhere. Use the BN-V11U/V12U/V20U battery packs and, to recharge them, the provided multi-voltage AC Power Adapter/ Charger. (An appropriate conversion adapter may be necessary to accommodate different designs of AC outlets in different countries.)

ATTENTION:

The product that you have purchased is powered by a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.

When the equipment is installed in a cabinet or on a shelf, make sure that is has sufficient space on all sides to allow for ventilation (10 cm (3-15/ 16") or more on both sides, on top and at the rear).

Do not block the ventilation holes. (If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)

No naked flame sources, such as lighted candles, should be placed on the apparatus.

When discarding batteries, environmental problems must be considered and the local rules or laws governing the disposal of these batteries must be followed strictly.

The apparatus shall not be exposed to dripping or splashing.

Do not use this equipment in a bathroom or places with water. Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases, potted plants, cups etc.) on top of this unit. (If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

4 EN

IMPORTANT PRODUCT SAFETY INSTRUCTIONS

Electrical energy can perform many useful functions. But improper use can result in potential electrical shock or fire hazards. This product has been engineered and manufactured to assure your personal safety. In order not to defeat the built-in safeguards, observe the following basic rules for its installation, use and servicing.

ATTENTION:

Follow and obey all warnings and instructions marked on your product and its operating instructions. For your safety, please read all the safety and operating instructions before you operate this product and keep this manual for future reference.

INSTALLATION

1. Power Sources

Operate your product only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. If your product is intended to operate from battery power, or other sources, refer to the operating instructions.

2. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

3. Power Cord Protection

Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

4. Ventilation

Slots and openings in the cabinet are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered.

•Do not block the openings by placing the product on a bed, sofa, rug or other similar surface.

•Do not place the product in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

5. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer.

ANTENNA INSTALLATION INSTRUCTIONS

1. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

2. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

3. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA LEAD IN WIRE

GROUND CLAMP

ANTENNA DISCHARGE UNIT

(NEC SECTION ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250. PART H)

NEC – NATIONAL ELECTRICAL CODE

810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

EN5

USE

1. Accessories

To avoid personal injury:

•Do not place this product on an unstable cart, stand, tripod, bracket or table. It may fall, causing serious injury to a child or adult, and serious damage to the product.

•Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with the product.

•Use a mounting accessory recommended by the manufacturer and follow the manufacturer’s instructions for any mounting of the product.

•Do not try to roll a cart with small casters across thresholds or deep-pile carpets.

2. Product and Cart

Combination

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

3. Water and Moisture

Do not use this product near water—for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the like.

4. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

5. Attachments

Do not use attachments not recommended by the manufacturer of this product as they may cause hazards.

6. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

7. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

PORTABLE CART WARNING (Symbol provided by RETAC)

SERVICING

1. Servicing

If your product is not operating correctly or exhibits a marked change in performance and you are unable to restore normal operation by following the detailed procedure in its operating instructions, do not attempt to service it yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

2. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen

into the product.

c. If the product has been exposed to rain or water. d. If the product does not operate normally by

following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

e. If the product has been dropped or damaged in

any way.

f. When the product exhibits a distinct change in

performance—this indicates a need for service.

3. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

4. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe operating condition.

6 EN

The image you shoot is recorded onto a video tape.

QUICK OPERATION GUIDE (VIDEO)

SUPPLY POWER INSERTING A VIDEO

Hook on.

Push in.

CASSETTE

BATTERY RELEASE

Using the battery pack

Hook its end to the camcorder and push the battery pack in until it locks in place . (Charging procedure, Z pg. 10)

To remove the battery pack

Slide BATTERY RELEASE and pull out the battery pack.

1 Open the LCD monitor fully. 2 Slide EJECT to open the cassette holder. 3 Insert a video cassette. 4 Press PUSH to close the cassette holder.

(For more details, Z pg. 12)

PUSH Button EJECT Switch

PLAYBACK SHOOTING

Rewind (

Stop (5) Button

1 Set the System Select Switch to “VIDEO”. 2 Set the Power Switch to “PLAY”. 3 Press

— The tape will automatically stop at the

4 Press

— Playback starts and the playback picture

•To stop playback, press 5. (For more details, Z pg. 39.)

•The viewfinder switches off automatically to

save power when the LCD monitor is opened at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is opened/closed at approx. 60 degrees.

Or simply play back the tape on a VHS VCR using the Cassette Adapter (VHS Playpak).

Z pg. 41

) Button

Play/Pause (4/6) Button

beginning of the tape.

/6.

appears.

Set to “VIDEO”.

Set to “PLAY”.

Recording Start/Stop Button

Set to “VIDEO”.

1 Turn the LENS COVER Open/Close Ring to

open the lens cover.

2 Set the System Select Switch to “VIDEO”. 3 Set the Power Switch to “AUTO” or “PRO.”.

— The power lamp will light and an image

will appear.

4 Press the Recording Start/Stop Button.

— Recording starts.

•To stop recording temporarily, momentarily press the Recording Start/Stop Button once again.

(For more details, Z pgs. 18, 19)

•The viewfinder switches off automatically to

save power when the LCD monitor is opened at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is opened/closed at approx. 60 degrees.

LENS COVER Open/Close Ring

Set to “AUTO” or “PRO.”.

QUICK OPERATION GUIDE (D.S.C.)

A still image you shoot is stored in the camcorder's built-in memory.

EN7

SUPPLY POWER

Hook on.

Push in.

BATTERY RELEASE

Using the battery pack

Hook its end to the camcorder and push the battery pack in until it locks in place . (Charging procedure, Z pg. 10)

To remove the battery pack

Slide BATTERY RELEASE and pull out the battery pack.

PLAYBACK

Next/Previous Page

/PAGE – or 3/PAGE +) Buttons

(

SHOOTING

SNAPSHOT Button

LENS COVER Open/Close Ring

Set to “AUTO” or “PRO.”.

Set to “D.S.C.”.

1 Turn the LENS COVER Open/Close Ring to

open the lens cover.

2 Set the System Select Switch to “D.S.C.”. 3 Set the Power Switch to “AUTO” or “PRO.”.

— The power lamp will light and an image

will appear.

4 Press the SNAPSHOT Button.

— A still image is shot and is stored in the

camcorder’s memory.

(For more details, Z pgs. 20 – 22)

•The viewfinder switches off automatically to

save power when the LCD monitor is opened at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is opened/closed at approx. 60 degrees.

Set to “PLAY”.

Set to “D.S.C.”.

1 Set the System Select Switch to “D.S.C.”. 2 Set the Power Switch to “PLAY”.

— A still image stored in memory appears.

3 Press

still image you want to view.

(For more details, Z pg. 44.)

•The viewfinder switches off automatically to

save power when the LCD monitor is opened at an angle of over 60 degrees.

•The LCD monitor turns on/off when it is opened/closed at approx. 60 degrees.

/PAGE – or 3/PAGE + to select the

8 EN

XFIT

DEMO MODE

MAJOR FEATURES

Integrated Auto Light

Z pg. 27)

(

Program AE with Special Effects (

n Electronic Fog Filter n ND Effect n Sepia n Twilight n Sports n Nega/Posi n 1/2000 sec. High Speed Shutter

Z pg. 29)

Super VHS-ET (Z pg. 15)

Digital Still Camera Built-in (PC communication capable)

Z pg. 20 – 22, 44 – 51)

(

Picture Stabilizer (Z pg. 25)

Digital Hyper Zoom

Z pg. 25)

(

Zoom in

Zoom out

TBC (Time Base Corrector)

Z pg. 40)

(

NOTES about Automatic Demonstration

Automatic Demonstration takes place when ”DEMO MODE” is set to ”ON” (factory-preset).

Available when the System Select Switch is set to “VIDEO” and the Power Switch is set to ”AUTO” or ”PRO.”.

Operating the Power Zoom Lever during the demonstration stops the demonstration temporarily. If the Power Zoom Lever is not moved for more than 1 minute after that, the demonstration will resume.

To cancel Automatic Demonstration, set the Power Switch to “PRO.” and press MENU while the demo is in progress. This takes you directly to the demo mode’s Setting Menu (so you will not have to go through the main Menu Screen.) Rotate the Select Wheel to select “OFF” and press it.

* ”DEMO MODE” remains ”ON” even if the camcorder power is turned off.

NOTE:

When a tape whose Erase Protection tab is in the position that allows recording is loaded in the camcorder, demonstration is not available.

Cassettes marked and can be used with this camcorder.

Setting Menu

PROVIDED ACCESSORIES

EN9

• AC Power Adapter/Charger AA-V16U

• Remote Control Unit RM-V715U

• Shoulder Strap

• Cassette Adapter (VHS Playpak) C-P7U

(for Windows® PC)

• PC Connection Cable

• Lithium Battery CR2025 (for clock operation)

• Battery Pack BN-V11U

• DC Cord

• CD-ROM including two software programs

Optional Accessories

• Battery Packs BN-V12U, BN-V20U, BN-V856U

• Car Battery Charger BH-V3U

• Battery Charger BH-VC10U

• Audio/Video Cable

• S-Video Cable QAM0004-004

• Car Battery Cord AP-V7U

• Compact S-VHS (

• Compact VHS (

• Active Carrying Bag CB-V7U

) Cassettes ST-C-40/30/20

) Cassettes TC-40/30/20

Some accessories are not available in some areas. Please consult your nearest JVC dealer for details on accessories and their availability.

10 EN

Battery pack BN-V12U or BN-V20U

Marks

CHARGE indicator

AC Power Adapter/Charger AA-V16U

DC OUT connector

Battery pack

BN-V11U BN-V12U (optional) BN-V20U (optional)

ATTENTION:

Charging a battery with some charge remaining reduces that battery’s capacity. Perform the procedure below to fully discharge the battery pack before recharging.

1. Attach the battery pack to the camcorder

and make sure a cassette is then set the Power Switch to ”AUTO” or ”PRO.”.

2. The camcorder power turns off

automatically when discharging is complete.

When you are not using a battery pack for a long period of time, be sure to fully discharge it before storing because leaving a battery with some charge left over also reduces performance.

Charging time

approx. 1 hr. 10 min. approx. 1 hr. 10 min. approx. 1 hr. 50 min.

Charge marker

not

To AC outlet

inserted,

GETTING STARTED

Power

This camcorder’s 3-way power supply system lets you choose the most appropriate source of power. Do not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

Make sure you unplug the camcorder’s DC cord from

the AC Power Adapter/Charger. Plug the AC Adapter/ Charger’s power cord into an AC outlet.

Align the marks and slide the battery pack in the

direction of the arrow until it locks in place. The CHARGE indicator begins blinking to indicate charging has started.

When the CHARGE indicator stops blinking but stays

lit, charging is finished. Slide the battery in the opposite direction of the arrow and lift off. Remember to unplug the AC Adapter/Charger’s power cord from the AC outlet.

Charge Marker

A charge marker is provided on the battery pack to help you remember whether it has been charged or not. Two colors are provided (red and black)—you choose which one means charged and which means discharged.

NOTES:

●

Perform charging where the temperature is between 10° and 35°C (50°F and 95°F). 20° to 25°C (68°F to 77°F) is the ideal temperature range for charging. If the environment is too cold, charging may be incomplete.

●

Charging times noted above are for a fully discharged battery pack.

●

Charging time varies according to the ambient temperature and the status of the battery pack.

●

To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.

●

If you connect the camcorder’s DC cord to the adapter during battery charging, power is supplied to the camcorder and charging stops.

●

Since the AC Power Adapter/Charger processes electricity internally, it becomes warm during use. Be sure to use it only in well-ventilated areas.

●

When charging the battery pack for the first time or after a long storage period, the CHARGE indicator may not light. In this case, remove the battery pack from the AC Power Adapter/Charger, then try charging again.

●

If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.

●

Remember to set the charge marker after charging a battery pack or after detaching a discharged one from your camcorder.

Hook on.

Push in.

BATTERY RELEASE Switch

ATTENTION:

Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can result in a camcorder malfunction.

INFORMATION:

VU-V856KIT is a set composed of the BNV856U battery pack and AA-V80U AC Power Adapter/Charger. Read the VU-V856KIT’s instruction manuals before using. It is impossible to charge the BN-V856U battery pack using the provided AC Power Adapter/ Charger. Use the optional AA-V80U AC Power Adapter/Charger.

EN11

USING THE BATTERY PACK

Hook its end to the camcorder and push the battery pack in until it locks in place .

•

If the battery pack is attached in the wrong position, a malfunction may occur.

To Detach The Battery Pack . . .

.... slide BATTERY RELEASE and pull out the battery pack.

Approximate recording time

LCD

Battery pack

BN-V11U

BN-V12U (optional)

BN-V20U (optional)

BN-V856U (optional)

( ) : when the video light is on.

monitor off/ Viewfinder on

1 hr. 20 min.

(45 min.)

1 hr. 20 min.

(45 min.)

2 hrs. 10 min.

(1 hr. 15 min.)

8 hrs. 30 min.

(5 hrs. 10 min.)

NOTES:

●

Recording time is reduced significantly under the following conditions:

•

Zoom or Record-Standby mode is engaged repeatedly.

•

The LCD monitor is used repeatedly.

●

Before extended use, it is recommended that you prepare enough battery packs to cover 3 times the planned shooting time.

LCD monitor on/ Viewfinder off

1 hr. 10 min.

(40 min.)

1 hr. 10 min.

(40 min.)

1 hr. 55 min.

(1 hr. 10 min.)

7 hrs. 40 min.

(4 hrs. 50 min.)

LCD monitor on/ Viewfinder on

1 hr. 5 min.

(40 min.)

1 hr. 5 min.

(40 min.)

1 hr. 45 min. (1 hr. 5 min.)

7 hrs.

(4 hrs. 30 min.)

To DC IN connector

Core filter

DC Cord

Car Battery Cord AP-V7U (optional)

Car Battery Charger/Adapter BH-V3U (optional)

To DC OUT connector

AC Power Adapter/ Charger AA-V16U

To AC outlet

To car’s cigarette lighter socket

USING AC POWER

Use the AC Power Adapter/Charger (connect as shown in the illustration).

NOTES:

●

The provided AC Power Adapter/Charger features automatic voltage selection in the AC range from 110 V to 240 V.

●

For other notes, Z pg. 10.

USING A CAR BATTERY

Use the optional Car Battery Cord or Car Battery Charger/ Adapter (connect as shown in the illustration).

NOTES:

●

When using the car battery, leave the engine idling.

●

The optional Car Battery Charger (BH-V3U) can also be used to charge the battery pack (except BN-V20U/ V856U).

●

When using the optional Car Battery Charger or Car Battery Cord (AP-V7U), refer to the respective instruction booklet.

12 EN

Slot

GETTING STARTED

(cont.)

Clock (Lithium) Battery Insertion/Removal

This battery is necessary for clock operation and to perform date/time settings.

Switch off the unit’s power and remove the power

supply unit (battery pack, AC Power Adapter/Battery Charger, etc.).

Pull out the battery holder to remove it from the

camcorder.

Battery holder

Cassette holder

Erase Protection tab Gear

EJECT SwitchPUSH Button

Turn to take up slack.

Insert the battery in the holder, and be sure to have

the “+” mark visible.

Slide the holder back into the slot until you hear a

click.

NOTES:

●

See “SAFETY PRECAUTIONS” (Z pg. 2) for information on safe handling of lithium batteries.

●

To avoid losing the battery and/or battery holder, place the camcorder with the grip side up as shown in the illustration when inserting/removing the battery.

Loading/Unloading A Cassette

Open the LCD monitor fully.

Slide EJECT until the cassette holder opens. Do not

use force to open.

Insert or remove a cassette. When inserting, make

sure the label is facing outward.

Press PUSH to close the cassette holder until it locks

into place. Close the LCD monitor.

NOTES:

●

Closing the LCD monitor while the cassette holder is still open may cause damage to the LCD monitor.

●

The cassette holder can’t be opened unless a power supply is attached.

●

Make sure that the tape is not slack when loading the cassette. If there is any slack, turn the gear on the cassette in the direction of the arrow to take up the slack.

●

Make sure the Erase Protection tab is in the position that allows recording. If not, slide the tab. Some cassettes have removable tabs. If the tab has been removed, cover the hole with adhesive tape.

●

The cassette holder cannot be opened while the camcorder is in the record mode.

D T

. E

Z L

O E

MACRO

O O O

N FNF

System Select Switch

Date/Time Settings

Set the System Select Switch to “VIDEO” or “D.S.C.”,

and set the Power Switch to “PRO.”. The power lamp comes on.

Press MENU. The Menu Screen appears.

EN13

Select Wheel

DATE / T IMPE

Display

GO.

N E

GO.

N E

MENU Button

GFLISH

M28

GFLISH

Power Switch

Menu Screen 1

Menu Screen 2

DATE/TIME Menu

12-hour indication with AM or PM

Rotate the Select Wheel to move the highlight bar to

“NEXT” in Menu Screen 1 and press it to display Menu Screen 2. Then, rotate it to move the highlight bar to “DATE/TIME” and press it. The DATE/TIME Menu appears.

•To return to the previous settings, rotate the Select Wheel to move the highlight bar to “EXIT” and press it, then go to step 7.

•To set only the time without changing the date, go to step 5.

To set “YEAR”, “MONTH” or “DAY”, rotate the Select

Wheel to move the highlight bar to the desired item, and press it. When the setting begins blinking, rotate the Select Wheel until the correct setting appears and then press it. The setting stops blinking. Repeat for other date settings.

Rotate the Select Wheel to move the highlight bar to

“TIME” and then press it. When the hour setting begins blinking, rotate the Select Wheel until the correct setting appears and then press it. When the hour setting stops blinking and the minute setting begins blinking, rotate the Select Wheel until the correct setting appears and then press it. The minute setting stops blinking.

When none of these settings (“YEAR”, “MONTH”,

“DAY”, “TIME”) blinks, rotate the Select Wheel to move the highlight bar to “EXIT”, and press it. The Menu Screen reappears with the highlight bar on “RETURN”.

Press the Select Wheel to close the Menu Screen.

NOTE:

To display the date and time in the camcorder’s display and on a connected TV, see “Date/Time Insert” (Z pg. 33).

14 EN

T30

P S

C A

T P

U S

R H

E O

RGOTHO

S F

T U

ALNLDARD

T T

P S

E A

L P

C A

E E

T P

U S

L R H

A E

E O

C N

RGOTHO

T S F

F 4

T U

F 0

ALNLDARD

GETTING STARTED

Recording Mode Setting

Set depending on your preference.

(cont.)

System Select Switch

Select Wheel

SP/EP Recording Mode Button

Viewfinder

Display

TAPE LENGTH

Power Switch

MENU Button

Tape length indicator

Recording mode indicator

Menu Screen

TAPE LENGTH Setting Menu

Set the System Select Switch to “VIDEO”, then set the

Power Switch to “AUTO” or “PRO.”. Press SP/EP for more than 1 second. “SP” (Standard Play) provides higher picture and sound quality and is better for dubbing, while “EP” (Extended Play) is more economical, providing three times the recording time.

NOTE:

If the recording mode is switched during recording, the playback picture will be blurred at the switching point.

Tape Length Setting

Set the tape length according to the length of the tape used.

Set the Power Switch to “PRO.”, then press MENU.

Rotate the Select Wheel to move the highlight bar to

“TAPE LENGTH”, then press it. The TAPE LENGTH Setting Menu appears.

Rotate the Select Wheel to move the highlight bar to

the correct tape length setting. T20=20 minutes of recording time, T30=30 minutes, T35=35 minutes, and T40=40 minutes (in SP).

•To return to the previous setting, rotate the Select Wheel to move the highlight bar to “EXIT”.

Press the Select Wheel. The Menu Screen reappears

with the highlight bar on “RETURN”. Press the Select Wheel again to close the Menu Screen.

NOTE:

The tape remaining time (Z pg. 18) displayed in the viewfinder is correct only if the correct tape length has been selected.

T T

P S

E A

L P

C A

E E

T P

U S

L R H

A E

E O

C N

RGOTHO

T S F

F 3

T U

F 0

ALNLDARD

Select Wheel

Power Switch

MENU Button

EN15

Recording Format Setting

Set the recording format according to the format of the tape used or type of recording you wish to perform.

Set the Power Switch to “PRO.”. Press MENU.

If a VHS cassette is loaded . . .

.... rotate the Select Wheel to move the highlight bar

to “S-VHS ET”, then press it. The S-VHS ET Setting Menu appears.

If an S-VHS cassette is loaded . . .

.... rotate the Select Wheel to move the highlight bar

to “S-VHS”, then press it. The S-VHS Setting Menu appears.

Display: when a VHS cassette is loaded.

–

FXF

RGO

E E

S–VHS E T

ALNLDARD

Menu Screen

When an S-VHS cassette is loaded: S-VHS

Setting Menu

Menu Screen

Normal Screen

Rotate the Select Wheel to set to either of the

parameters, then press it. Press the Select Wheel. The Menu Screen reappears with the highlight bar on “RETURN”.

In the S-VHS ET Setting Menu,

ON : Records with S-VHS picture quality on a VHS

cassette (factory-preset). This is called Super VHS ET (Expansion Technology).

OFF: Records in VHS.

In the S-VHS Setting Menu,

ON : Records in S-VHS on an S-VHS cassette

(factory-preset).

OFF: Records in VHS on an S-VHS cassette.

Press the Select Wheel to close the Menu Screen.

•When the S-VHS ET mode is engaged, “S-ET” is displayed.

•During S-VHS record mode, “S“ is displayed.

•When S-VHS ET or S-VHS recording starts, “S-VHS REC.” is displayed for approx. 3 seconds.

NOTE:

If a cassette is not loaded, “S-VHS” will be displayed in the Menu Screen.

CONTINUED ON NEXT PAGE

16 EN

GETTING STARTED

NOTES about S-VHS and S-VHS ET

JVC EHG (Extra High Grade) tapes are recommended for superior results. Use S-VHS tape for storing recordings for an extended period or for recording important scenes, as it enables higher-quality recording and playback.

With some tapes, better picture quality may not be obtained even with S-VHS ET recording. It is recommended that you do test record beforehand to make sure whether better results can be obtained.

If the S-VHS ET mode or recording format is switched during recording, the playback picture will be blurred at the switching point.

It is recommended that tapes recorded in the SP mode on this camcorder be played back on this camcorder.

Noise may appear on-screen when tapes recorded in the EP mode are played back.

Tapes recorded in S-VHS or S-VHS ET mode can be played back not only on this camcorder but also on a Super VHS VCR or a VCR equipped with the SQPB (S-VHS QUASI PLAYBACK) function.

— When tapes recorded in S-VHS or S-VHS ET mode are played back on a VCR equipped with the

SQPB (S-VHS QUASI PLAYBACK) function, S-VHS picture quality is not available.

— Tapes recorded in S-VHS ET mode cannot be played back on some VCRs, including some JVC VCRs.

Tapes recorded in S-VHS or S-VHS ET mode cannot be played back correctly on a normal VHS VCR.

You can play back S-VHS ET recordings not only on this camcorder but also on another VHS VCR equipped with S-VHS ET.

— It is recommended to specifically label S-VHS ET recordings so you can easily distinguish them from

regular VHS recordings.

S-VHS ET does not work with S-VHS tapes.

To avoid on-screen noise, do not perform Still Playback or Shuttle Search repeatedly.

If the picture contains a lot of jitter or noise, use a cleaning cassette.

(cont.)

Compatibility Between S-VHS And VHS

Recording Playback

Blank tape Camcorder Recorded tape

S-VHS-C cassette

VHS-C cassette

S-VHS/S-VHS ET recordings

VHS recordings

Cassette adapter

Cassette adapterBlank tape Camcorder Recorded tape

S-VHS VCR

VHS VCR with SQPB

function

•The recorded format (S-VHS or VHS) is automatically detected when playback begins.

Regular VHS VCR

•S-VHS recorded tapes cannot be viewed on regular VHS VCRs, other than those equipped with the SQPB (S-VHS QUASI PLAYBACK) function.

PAUSE

Power Zoom Lever

Recording Start/Stop Button

Grip Adjustment

Separate the Velcro strip.

Pass your right hand through the loop and grasp the

grip.

Adjust so that your thumb and fingers can easily

operate the Recording Start/Stop Button and Power Zoom Lever. Refasten the Velcro strip.

EN17

180°180

Set to “CAMERA” (“AUTO” or “PRO.”).

Viewfinder Adjustment

Set the Power Switch to “CAMERA” (“AUTO” or

“PRO.”).

Adjust the viewfinder manually for best viewability.

Turn the Diopter Adjustment Control until the

indications in the viewfinder are clearly focused.

Shoulder Strap Attachment

Following the illustration, thread the strap through the

eyelet 1, then fold it back and thread it through the buckle 2. Repeat the procedure to attach the other end of the strap to the other eyelet 3, making sure the strap is not twisted.

Adjust as shown in the illustration 4.

Tripod Mounting

Align the screw and camera direction stud on the

tripod with the camera’s mounting socket and stud hole. Then tighten the screw.

CAUTION:

When using a tripod, be sure to open and extend its legs fully to stabilize the camcorder. To prevent damage to the unit caused by falling over, do not use a small-sized tripod.

18 EN

BR I GHT –

–––––6–––––

25MIN

System Select Switch

LENS COVER Open/Close Ring

Power Switch

Recording Start/Stop Button

Tape remaining time indicator (Approximate)

BASIC VIDEO RECORDING

NOTE:

You should already have performed the procedures listed below. If not, do so before continuing.

●

Power (Z pg. 10)

●

Recording Mode Setting (Z pg. 14)

●

Load A Cassette (Z pg. 12)

●

Grip Adjustment (Z pg. 17)

●

Viewfinder Adjustment (Z pg. 17)

Shooting While Watching The Viewfinder

Make sure the LCD monitor is closed and locked.

Turn the LENS COVER Open/Close Ring to open the lens cover. Set the System Select Switch to “VIDEO”, then set the Power Switch to “CAMERA” (“AUTO” or “PRO.”). The power lamp lights and the camcorder enters the Record-Standby mode. “PAUSE” is displayed in the viewfinder.

MIN 119MIN

(Now calculating)

(Blinking) (Blinking) (Blinking)

120MIN

1MIN0MIN

2MIN

3MIN

Press the Recording Start/Stop Button. “ ” appears

in the viewfinder while recording is in progress.

Shooting While Watching The LCD Monitor

Make sure the LCD monitor is fully open. Turn the

90°

180°

Select Wheel (BRIGHT)

DISPLAY Button

To Adjust The Brightness Of The LCD Monitor

.... rotate the Select Wheel (BRIGHT) until the

bright level indicator on the display moves and the appropriate brightness is reached.

Power Switch Position

AUTO : Suitable for standard recording using NO special effects or manual adjustments. PRO. : Allows you to set recording functions using the menus for more creative capabilities. OFF : Switches off the camcorder. PLAY : Allows you to play back your recordings.

LENS COVER Open/Close Ring to open the lens

cover. Set the System Select Switch to “VIDEO”, then set the Power Switch to “CAMERA” (“AUTO” or “PRO.”). The power lamp lights and the camcorder enters the Record-Standby mode. “PAUSE” is displayed in the LCD monitor.

Tilt the LCD monitor upward/downward for best

viewability and press the Recording Start/Stop Button. “ ” appears in the LCD monitor while recording is in progress.

NOTE:

When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may be difficult to see. If this happens, use the viewfinder instead.

To Stop Recording . . .

.... press the Recording Start/Stop Button. The camcorder

re-enters the Record-Standby mode.

EN19

NOTES:

●

When the Power Switch is set to CAMERA and the LCD monitor is opened at an angle of 60 degrees or more, the LCD monitor switches on and the viewfinder switches off automatically to save power.

●

The cassette holder cannot be opened unless a power supply is attached.

●

There may be a delay after you slide EJECT until the cassette holder opens. Do not use force.

●

The time required to calculate the remaining tape length, and the accuracy of the calculation, may vary according to the type of tape used.

●

The tape remaining time indicator is correct only if the correct tape length has been selected (Z pg. 14).

●

“TAPE END” appears when the tape reaches its end, and the power goes off automatically if left in this condition for 5 minutes. “TAPE END” also appears when a cassette whose tape is already at its end is loaded.

●

If the Record-Standby mode continues for 5 minutes without performing Zoom or any other operations, the camcorder’s power shuts off automatically. Set the Power Switch to “OFF”, and then back to “CAMERA” to turn the camcorder on again.

●

If the Recording Start/Stop button is pressed after the Record-Standby mode has continued for over 5 minutes, recording may not start immediately.

●

If you are recording on a cassette from the middle (such as when a tape is removed and re-inserted during recording), use the Retake function (Z pg. 26) to find the end of the last recording so you do not erase any of it.

●

While shooting, sound is not heard from the speaker.

JOURNALISTIC SHOOTING

In some situations, different shooting angles may provide more dramatic results. Hold the camcorder in the desired position and tilt the LCD monitor in the most convenient direction. It can rotate 270° (90° downward, 180° upward).

INTERFACE SHOOTING

The person you shoot can view himself/herself in the LCD monitor, and you can even shoot yourself while viewing your own image in the LCD monitor. Open the LCD monitor and tilt it upward to 180 degrees so that it faces forward. When the LCD monitor is tilted upward to an angle of over approx. 105 degrees, the monitor image is inverted vertically, and the viewfinder also switches on. Point the lens toward the subject (yourself when selfrecording) and start recording. During Interface Shooting, the monitor image and indications do not appear inverted as they would when viewing a mirror.

NOTE:

The monitored image can be viewed on the LCD monitor and in the viewfinder.

LCD MONITOR/VIEWFINDER INDICATIONS

Press DISPLAY for more than 1 second to make the following indications appear/disappear from the camcorder’s display: cassette warning, tape remaining time, battery pack remaining power indicator and tape length indicator (Z pg. 62, 63).

NOTE:

Even if the indications are off, the tape remaining time

Self-Recording

appears blinking when the tape is near its end, and the battery pack remaining power indicator appears blinking when the power is almost gone.

20 EN

T T

P S

E A

L P

C A

E E

T P

U S

L R H

A E

E O

C N

RGOTHO

T S P

F 3

F 0

ANN–DUAPRD

T T

E A

L P

E E

L R

A E

C N

RGOTHO

T S

F 3

F 0

ALNLDARD

System Select Switch

Select Wheel

–

Normal Screen

BASIC DIGITAL STILL CAMERA (D.S.C.) SHOOTING

LENS COVER Open/Close Ring

SNAPSHOT Button

Power Switch

MENU Button

Display

NAPSHOT

Menu Screen

SNAPSHOT Menu

Menu Screen

When shooting a still image, it is not recorded onto the tape, but it is stored in the camcorder's built-in memory in the selected Picture Mode. A stored still image data can be transferred to a PC, saved, and processed using a Paint Software program (Z pg. 45). A still image processed on the PC can be also inserted onto a tape (Z pg. 55).

MODE SELECTION

Turn the LENS COVER Open/Close Ring to open the

lens cover, then set the System Select Switch to “D.S.C.”. Set the Power Switch to “PRO.”. The power lamp lights and an image appears.

To select the Picture Mode, perform steps 2 and 3 of

“OPERATION” on pg. 22.

Rotate the Select Wheel to move the highlight bar to

“SNAPSHOT”, and press it. The SNAPSHOT Menu appears. Rotate the Select Wheel to move the highlight bar to the appropriate mode among the 4 Snapshot modes (Z pg. 21), and press it. Selection is complete.

The Menu Screen reappears with the highlight bar on

“RETURN”. Press the Select Wheel again to close the Menu Screen.

STILL IMAGE STORAGE

Press SNAPSHOT.

•Regardless of the Power Switch position (“AUTO” or “PRO.”), Snapshot recording takes place using the selected Snapshot mode.

•A still image is stored in the built-in memory and displayed for approx. 2 seconds. While the still image remains displayed, that image is in the process of being stored in memory, and it is therefore impossible to take another shot during that time. When the still image disappears and the scene you are currently aimed at appears on the screen, you may take another shot.

•The remaining number of shots available is displayed.

Snapshot mode

STD 34

Remaining number of shots

60 59 1

Pictrue mode display

FULL* (Snapshot mode with no frame)

PIN-UP* (Pin-Up mode)

MULTI-4 ** (Multi-Analyzer 4)

MULTI-9** (Multi-Analyzer 9)

(Blinking)

NOTES:

●

The remaining number of shots varies according to the selected Picture Mode. In the “STANDARD” mode, twice as many still images can be shot as in the “FINE”

mode.

●

Some sample images have been stored in the built-in memory at the factory. If you wish to delete them, first remove the “Protect” function (Z pg. 49), then perform the “Delete” function (Z pg. 50).

●

When the Power Switch is set to “AUTO”, it is not possible to select the Snapshot mode. You can use the Snapshot mode you selected in the “PRO.” mode.

●

If a Snapshot is taken while the camcorder is in the WIDE mode (Z pg. 31), the Snapshot image is recorded without the black bars at the top and bottom of the screen.

●

When the remaining number indicator displays “0” (blinking), it is not possible to continue storing pictures until you delete some shots to make room for new ones. Perform “DELETE” function in the Menu Screen to remove pictures you do not need (Z pg. 50).

●

When SNAPSHOT is pressed with the System Select Switch set to “VIDEO”, the picture is stored in the camcorder's built-in memory (in the Snapshot mode selected in the “VIDEO” system) and also onto the tape (if a tape is in the camcorder) (Z pg. 23).

●

When you shoot in a dark environment, the still image will become coarse and its true colors will be lost.

* There is a momentary camera shutter-type blackout

together with the image.

** Continuous camera shutter-type blackout takes place 4

or 9 times with the image, like serial photography, then the 4 or 9 still images you took are displayed.

EN21

CONTINUED ON NEXT PAGE

22 EN

T T

E A

L P

E E

A E

C N

RGOTHO

F 3

F 0

ALNLDARD

T T

P S

E A

L P

C A

E E

T P

U S

L R H

A E

E O

C N

RGOTHO

T F P

F 3

I I

F 0

NNE

–

BASIC D.S.C. SHOOTING

System Select Switch

Select Wheel

Display

CTURE

NTDAPRID

Normal Screen

Power Switch

MENU Button

Menu Screen

PICTURE Menu

Menu Screen

FEATURE:

Picture Mode Setting

PURPOSE:

There are two image settings you can choose from when storing in the camcorder's memory: FINE and STANDARD. FINE allows you to shoot up to approx. 30 still images in a format based on JPEG (Joint Photographic Experts Group). Since the quality of image is better than “STANDARD”, “FINE” is more suitable for post-production on a PC. “STANDARD” allows you to shoot up to approx. 60 still images in a format based on JPEG (Joint Photographic Experts Group). Since in this mode, twice as many still images can be shot as in the “FINE” mode, select this mode when you wish to shoot many still images.

OPERATION:

1) Set the System Select Switch to “D.S.C.”. Set the

Power Switch to “PRO.”.

2) Press MENU. The Menu Screen appears.

3) Rotate the Select Wheel to move the highlight bar to

“PICTURE”, and press it. The PICTURE Menu appears. Rotate the Select Wheel to move the highlight bar to “FINE” or “STANDARD”, and press it. Selection is complete.

4) The Menu Screen reappears with the highlight bar

on “RETURN”. Press the Select Wheel again to close the Menu Screen.

NOTES:

●

The picture mode’s factory-preset is STANDARD.

●

To store the still images you shot, we recommend that you transfer them to a computer and save them on disk (Z pg. 45), or transfer them to a VCR connected to the camcorder and record them onto a tape.

●

When the Power Switch is set to “CAMERA” (“AUTO” or “PRO.”) and the LCD monitor is opened at an angle of 60 degrees or more, the LCD monitor switches on and the viewfinder switches off automatically to save power. When you use the LCD monitor outdoors in direct sunlight, the LCD monitor may be difficult to see. If this happens, use the viewfinder instead.

●

The Picture Mode can be switched to either “FINE”or “STANDARD”. Since the remaining number of shots available depends on the selected Picture Mode, switching the Picture Mode will vary this number.

+ 50 hidden pages