JVC GR-DVM55EG, GR-DVM55U, GR-DVM75U, GR-DVM55 Instructions Manual

LYT0735-001B

EN

DIGITAL VIDEO CAMERA

INSTRUCTIONS

GR-DVM75
GR-DVM55

Please visit our Homepage on the World Wide
Web and answer our Consumer Survey
(in English only):

http://www.jvc-victor.co.jp/english/index-e.html

The D.S.C. (Digital Still Camera) features are
available on GR-DVM75.

ENGLISH

CONTENTS

AUTOMATIC
DEMONSTRATION

6

GETTING STARTED 7 – 16

VIDEO RECORDING &
PLAYBACK 17 – 24

VIDEO RECORDING ............. 18 – 20

VIDEO PLAYBACK ............... 21 – 24

DIGITAL STILL CAMERA (D.S.C.)
RECORDING &
PLAYBACK 25 – 36

D.S.C. RECORDING .............. 26 – 27

D.S.C. PLAYBACK ................ 28 – 36

ADVANCED
FEATURES 37 – 75

USING MENUS FOR

DETAILED ADJUSTMENT ...... 38 – 44

FOR RECORDING ................ 45 – 56

DUBBING ......................... 57 – 61

USING THE REMOTE

CONTROL UNIT ................ 62 – 73

SYSTEM CONNECTIONS ........ 74 – 75

REFERENCES 76 – 99

DETAILS ................................... 77

TROUBLESHOOTING ............ 78 – 83

USER MAINTENANCE ................... 84

INDEX ............................. 85 – 92

CAUTIONS ........................ 93 – 95

TERMS ............................ 96 – 97

SPECIFICATIONS ................. 98 – 99

For Customer Use:

Enter below the Model No. and Serial No. which is located on the
bottom of cabinet. Retain this information for future reference.

Model No.

Serial No.

The camcorder illustrations
appearing in this instruction
manual are of the GR-DVM75.

2 EN

CAUTIONS:

● This camcorder is designed to be used with NTSC-type color television signals. It cannot be used for
playback with a television of a different standard. However, live recording and LCD monitor/viewfinder
playback are possible anywhere.

● Use the JVC BN-V507U/V514U battery packs and, to recharge them or to supply power to the
camcorder from an AC outlet, use the provided multi-voltage AC Adapter. (An appropriate conversion
adapter may be necessary to accommodate different designs of AC outlets in different countries.)

Using This Instruction Manual

•All major sections and subsections are listed in the Table Of Contents on the cover page.

•Notes appear after most subsections. Be sure to read these as well.

•Basic and advanced features/operation are separated for easier reference.

It is recommended that you . . .

.... refer to the Index (墌 pgs. 85 – 92) and familiarize yourself with button locations, etc. before use.

.... read thoroughly the Safety Precautions and Safety Instructions that follow. They contain extremely

important information regarding the safe use of this product.

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the
product's enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.

You are recommended to carefully read the cautions on pages 93 through 95 before use.

NOTES:

●

The rating plate (serial number plate) and safety
caution are on the bottom and/or the back of
the main unit.

●

The rating information and safety caution of the
AC Adapter are on its upper and lower sides.

WARNING:
TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS APPARATUS
TO RAIN OR MOISTURE.

Dear Customer,

Thank you for purchasing this digital video camera. Before use, please read the safety information and
precautions contained in the following pages to ensure safe use of this product.

Caution: (applies to Jack Box)

To reduce the risk of fire, do not remove
cover. No user-serviceable parts inside.
Refer servicing to qualified service person.

EN3

When the equipment is installed in a cabinet or on a shelf, make sure that it has sufficient space on all
sides to allow for ventilation (10 cm (3-15/16") or more on both sides, on top and at the rear).

Do not block the ventilation holes.
(If the ventilation holes are blocked by a newspaper, or cloth etc. the heat may not be able to get out.)

No naked flame sources, such as lighted candles, should be placed on the apparatus.

When discarding batteries, environmental problems must be considered and the local rules or laws
governing the disposal of these batteries must be followed strictly.

The apparatus shall not be exposed to dripping or splashing.

Do not use this equipment in a bathroom or places with water.
Also do not place any containers filled with water or liquids (such as cosmetics or medicines, flower vases,
potted plants, cups etc.) on top of this unit.
(If water or liquid is allowed to enter this equipment, fire or electric shock may be caused.)

IMPORTANT SAFETY INSTRUCTIONS

(1) Read these instructions.

(2) Keep these instructions.

(3) Heed all warnings.

(4) Follow all instructions.

(5) Do not use this apparatus near water.

(6) Clean only with dry cloth.

(7) Do not block any ventilation openings.

Install in accordance with the
manufacturer’s instructions.

(8) Do not install near any heat sources such

as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.

(9) Only use attachments/accessories specified

by the manufacturer.

(10) Use only with the cart,

stand, tripod, bracket,
or table specified by
the manufacturer, or
sold with the
apparatus. When a
cart is used, use
caution when moving
the cart/apparatus combination to avoid
injury from tip-over.

(11) Unplug this apparatus during lightning

storms or when unused for long periods of
time.

(12) Refer all servicing to qualified service

personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.

4 EN

SAFETY PRECAUTIONS

Do not point the lens or the viewfinder directly into the sun. This can cause eye injuries, as well as
lead to the malfunctioning of internal circuitry. There is also a risk of fire or electric shock.

CAUTION!

The following notes concern possible physical damage to the camcorder and to the user.

When carrying, be sure to hold the camcorder firmly in your hand, with the grip strap securely
around your wrist. Carrying or holding the camcorder by the viewfinder and/or the LCD monitor
can result in dropping the unit, or in a malfunction.

Take care not to get your finger caught in the cassette holder cover. Do not let children operate the
camcorder, as they are particularly susceptible to this type of injury.

Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to
the camcorder.

CAUTION!

Connecting cables (Audio/Video, S-Video, etc.) to the camcorder and leaving it on top of the TV is
not recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.

䡲 This camcorder is designed exclusively for the digital video cassette, SD Memory Card and

MultiMediaCard. Only cassettes marked “

” and memory cards* marked “ ” or

“

” can be used with this unit.

Before recording an important scene . . .

.... make sure you only use cassettes with the Mini DV mark .

.... make sure you only use memory cards* with the mark

or .

.... remember that this camcorder is not compatible with other digital video formats.

.... remember that this camcorder is intended for private consumer use only. Any commercial

use without proper permission is prohibited. (Even if you record an event such as a show,
performance or exhibition for personal enjoyment, it is strongly recommended that you
obtain permission beforehand.)

*Memory cards can be used with GR-DVM75 only .

EN5

• AC Adapter
AP-V10U

• Remote Control Unit
RM-V717U

• CD-ROM

• PC Connection Cable
(GR-DVM55 only)

• Audio/Video Cable
(ø3.5 mini-plug to RCA plug)

• Editing Cable
GR-DVM75: Both plugs have 1 ring

around the pin.

GR-DVM55: One plug has 3 rings

around the pin and
the other has 1 ring
around the pin.

• Battery Pack
BN-V507U

• AAA (R03) Battery x 2
(for remote control unit)

• Memory Card
8 MB (GR-DVM75 only)
(Already inserted in the
camcorder)

• USB Cable
(GR-DVM75 only)

• Jack box
GR-DVM75: CU-V506

GR-DVM55: CU-V505

PROVIDED ACCESSORIES

NOTE:

In order to maintain optimum performance of the camcorder, provided cables may be equipped
with one or more core filter.

6 EN

MOD EDEMO –ONOFF

P

L

A

Y

O

F

F

AUTOMATIC DEMONSTRATION

Automatic Demonstration takes place
when “DEMO MODE” is set to “ON”
(factory-preset).

䡲 Available when the Power Switch is set to

“ ” or “ ” and no cassette is in the
camcorder.

䡲 Performing any operation during the

demonstration stops the demonstration
temporarily. If no operation is performed for
more than 1 minute after that, the demonstra­tion will resume.

䡲 “DEMO MODE” remains “ON” even if the

camcorder power is turned off.

䡲 To cancel Automatic Demonstration:

1. Set the Power Switch to “ ” while

pressing down the Lock Button located on
the switch and press the MENU Wheel in.
The Menu Screen appears.

2. Rotate the MENU Wheel to select “

SYSTEM” and press it. The SYSTEM Menu
appears.

3. Rotate the MENU Wheel to select “DEMO

MODE” and press it. The Sub Menu
appears.

4. Rotate the MENU Wheel to select “OFF”

and press it.

5. Rotate the MENU Wheel to select

“ RETURN”, and press it twice. The
normal screen appears.

Sub Menu

GR-DVM75 only

Lock Button

MENU Wheel

Power Switch

EN7

GETTING STARTED

GETTING STARTED

CONTENTS

Power

..................................................................... 8 – 9

Grip Adjustment

............................................................. 10

Viewfinder Adjustment

.................................................... 10

Tripod Mounting

............................................................. 10

Date/Time Settings

......................................................... 11

Loading/Unloading A Cassette

........................................... 12

Recording Mode Setting

................................................... 13

Loading A Memory Card (GR-DVM75 only)

........................... 14

Picture Quality Mode Setting (GR-DVM75 only)

...................... 15

Image Size Mode Setting (GR-DVM75 only)

.......................... 15

Operation Mode

............................................................. 16

8 EN

GETTING STARTED

(cont.)

Power

This camcorder’s 2-way power supply system lets you
choose the most appropriate source of power. Do not use
provided power supply units with other equipment.

CHARGING THE BATTERY PACK

1

Insert the terminal end 1 of the battery pack into the
battery pack mount, then firmly push the end 2 of
the battery pack in the direction of the arrow until it
locks into place as shown in the illustration.

2

Set the Power Switch to “OFF”. Connect the AC
Adapter to the camcorder 3.

3

Plug the AC Adapter into an AC outlet 4.
The CHARGE lamp on the camcorder blinks to
indicate charging has started.

4

When the CHARGE lamp stops blinking but stays lit,
charging is finished. Unplug the AC Adapter from the
AC outlet. Disconnect the AC Adapter from the
camcorder.

To Detach The Battery Pack . . .

.... slide BATT. RELEASE and detach it.

NOTES:

●

During charging, the camcorder cannot be operated.

●

Charging is not possible if the wrong type of battery is
used.

●

When charging the battery pack for the first time or
after a long storage period, the CHARGE lamp may not
light. In this case, remove the battery pack from the
camcorder, then try charging again.

●

If the battery operation time remains extremely short
even after having been fully charged, the battery is
worn out and needs to be replaced. Please purchase a
new one.

●

Using the optional AA-V50U AC Power Adapter/
Charger, you can charge the BN-V507U/V514U battery
pack without the camcorder. However, it cannot be
used as an AC adapter.

To AC outlet

AC Adapter

To DC IN
connector

Battery pack

BN-V507U

BN-V514U (optional)

Charging time

approx. 1 hr. 30 min.

approx. 2 hr. 45 min.

For other notes, 墌 pg. 77

3

4

1

2

Battery pack

CHARGE Lamp

BATT. RELEASE
Switch

Power Switch

Open the cover.

EN9

USING AC POWER

Use the AC Adapter (connect as shown in the illustration).

NOTES:

●

The provided AC Adapter features automatic voltage
selection in the AC range from 110 V to 240 V.

●

For other notes, 墌 pg. 77.

To DC IN
connector

To AC outlet

AC Adapter

ATTENTION:

Before detaching the power source, make
sure that the camcorder’s power is turned
off. Failure to do so can result in a
camcorder malfunction.

NOTES:

●

Recording time is reduced significantly
under the following conditions:

•

Zoom or Record-Standby mode is engaged
repeatedly.

•

The LCD monitor is used repeatedly.

●

Before extended use, it is recommended that
you prepare enough battery packs to cover 3
times the planned shooting time.

USING THE BATTERY PACK

Perform step 1 of “CHARGING THE BATTERY PACK”
(墌 pg. 8).

Approximate recording time

Battery pack

BN-V507U

BN-V514U
(optional)

BN-V840U
(optional)

BN-V856U
(optional)

LCD monitor off/

Viewfinder on

GR-DVM75 : 1 hr.
GR-DVM55 : 1 hr. 10 min.

GR-DVM75 : 2 hr. 10 min.
GR-DVM55 : 2 hr. 25 min.

GR-DVM75 : 6 hr. 10 min.
GR-DVM55 : 6 hr. 50 min.

GR-DVM75 : 9 hr.
GR-DVM55 : 10 hr.

LCD monitor on/

Viewfinder off

GR-DVM75 : 50 min.
GR-DVM55 : 1 hr.

GR-DVM75 : 1 hr. 50 min.
GR-DVM55 : 2 hr.

GR-DVM75 : 5 hr. 15 min.
GR-DVM55 : 5 hr. 50 min.

GR-DVM75 : 7 hr. 40 min.
GR-DVM55 : 8 hr. 20 min.

INFORMATION:

The extended-use battery pack kit is a set composed of a battery pack and AC Power Adapter/Charger:
VU-V840 KIT: BN-V840U battery pack & AA-V15U AC Power Adapter/Charger
VU-V856 KIT: BN-V856U battery pack & AA-V80U AC Power Adapter/Charger
Read the kit's instruction manual before using.
Neither BN-V840U nor BN-V856U can be charged by using the AC Adapter provided with this camcorder.
Use only the AA-V15U AC Power Adapter/Charger for BN-V840U battery pack and only AA-V80U AC
Power Adapter/Charger for BN-V856U battery pack. Also, by using the optional JVC VC-VBN856U DC
Cord, it will be possible to connect BN-V840U or BN-V856U battery packs to the camcorder and supply
power directly to the camcorder.

Lithium-ion is vulnerable in colder temperatures.

About Batteries

DANGER! Do not attempt to take the batteries apart, or expose them to flame or excessive heat, as it may

cause a fire or explosion.
WARNING! Do not allow the battery or its terminals to come in contact with metals, as this can result in a

short circuit and possibly start a fire.

The Benefits Of Lithium-Ion Batteries

Lithium-ion battery packs are small but have a large power capacity. However, when one is exposed to cold
temperatures (below 10°C/50°F), its usage time becomes shorter and it may cease to function. If this happens,
place the battery pack in your pocket or other warm, protected place for a short time, then re-attach it to the
camcorder. As long as the battery pack itself is not cold, it should not affect performance.

(If you’re using a heating pad, make sure the battery pack does not come in direct contact with it.)

Open the cover.

10 EN

PAUSE

P

L

A

Y

O

F

F

Grip Adjustment

1

Separate the Velcro strip.

2

Pass your right hand through the loop and grasp the
grip.

3

Adjust your thumb and fingers through the grip, to
easily operate the Recording Start/Stop button and
Power Switch and Power Zoom Lever. Be sure to
fasten the Velcro strip to your preference.

Viewfinder Adjustment

1

Set the Power Switch to “ ” or “ ” while pressing
down the Lock Button located on the switch.

2

Pull out the viewfinder fully.

3

Turn the Diopter Adjustment Control until the
indications in the viewfinder are clearly focused.

Diopter Adjustment
Control

Power Switch

GETTING STARTED

(cont.)

CAUTION:

When attaching the camera to a tripod, extend its
legs to stabilize the camcorder. It is not advised to use
small sized tripods. This may cause damage to the
unit by falling over.

Tripod Mounting

1

Align the screw on the tripod with the camera’s
mounting socket. Then tighten the screw.

•Some tripods are not equipped with studs.

Lock
Button

EN11

OF

F

FADER

/ W I P E

AM AEPROGR

ACAMER
LMAN UA

MSYSTE

DSC

END

AYDISPL

C

AN E

W. BAL

RE NEON S C

LCD / TV

UAOT

IMETDA TE /
T I ME CODE

CLOCK

ADJ .

–
–
– FFO

25 ’ 01

CED

30PM:5

NRETUR

CLOCK
ADJ .

25 ’ 01

CED

30PM:5

P

L

A

Y

O

F

F

Date/Time Settings

The date/time is recorded onto the tape at all times, but its
display can be turned on or off during playback
(墌 pg. 42, 43).

1

Set the Power Switch to “ ” while pressing down
the Lock Button located on the switch, then open
the LCD monitor fully or pull out the viewfinder
fully. The power lamp lights and the camcorder is
turned on.

2

Press the MENU Wheel in. The Menu Screen
appears.

3

Rotate the MENU Wheel to select “ DISPLAY”.
Press it and the DISPLAY Menu appears.

4

Rotate the MENU Wheel to select “CLOCK ADJ.”.
Press it and “month” is highlighted.
Rotate the MENU Wheel to input the month. Press
it. Repeat to input the day, year, hour and minute.
Rotate the MENU Wheel to select “ RETURN”, and
press it twice. The Menu Screen closes.

NOTE:

Even if you select “CLOCK ADJ.”, if the parameter is not
highlighted the camcorder’s internal clock continues to
operate. Once you move the highlight bar to the first
date/time parameter (month), the clock stops. When you
finish setting the minute and press the MENU Wheel in,
the date and time begin operation from the date and time
you have just set.

Display

MENU Wheel

Power Switch

Lock Button

DISPLAY Menu

Power lamp

GR-DVM75 only

12 EN

Loading/Unloading A Cassette

The camcorder needs to be powered up to load or eject a
cassette.

1

Slide down and hold OPEN/EJECT in the direction
of the arrow then pull the cassette holder cover
open until it locks. The cassette holder opens
automatically.

•Do not touch internal components.

2

Insert or remove a tape and press “PUSH HERE” to
close the cassette holder.

•Once the cassette holder is closed, it recedes
automatically. Wait until it recedes completely
before closing the cassette holder cover.

•When the battery’s charge is low, you may not be
able to close the cassette holder cover. Do not
apply force. Replace the battery with a fully
charged one before continuing.

3

Close the cassette holder cover firmly until it locks
into place.

OPEN/EJECT
Switch

Cassette holder

PUSH HERE

Cassette holder cover

Make sure the
window side is
facing out.

Erase protection tab*

Tape

Recording mode

SP LP

30 min. 30 min. 45 min.

60 min. 60 min. 90 min.

80 min. 80 min. 120 min.

Approximate recording time

NOTES:

●

It takes a few seconds for the cassette holder to open. Do not apply force.

●

If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try
again. If the cassette holder still does not open, turn the camcorder off then on again.

●

If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few
minutes later, insert it again.

●

When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time
before opening the cassette holder cover.

●

Closing the cassette holder cover before the cassette holder comes out may cause damage to the
camcorder.

●

Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder
is closed with the camcorder switched off, however, it may not recede. It is recommended to turn the
power on before loading or unloading.

●

When resuming recording, once you open the cassette holder cover a blank portion will be recorded on
the tape or a previously recorded scene will be erased (recorded over) regardless of whether the cassette
holder came out or not. See page 20 for information about recording from the middle of a tape.

*

To Protect Valuable Recordings . . .

....slide the erase protection tab on the back

of the tape in the direction of “SAVE”. This
prevents the tape from being recorded
over. To record on this tape, slide the tab
back to “REC” before loading it.

Be sure to press only the section labeled
“PUSH HERE” to close the cassette holder;
touching other parts may cause your finger to
get caught in the cassette holder, resulting in
injury or product damage.

GETTING STARTED

(cont.)

EN13

REC MODE – SP

LP

P

L

A

Y

O

F

F

MENU Wheel

Lock Button

Power lamp

Recording Mode Setting

Set the tape recording mode depending on your
preference.

1

Set the Power Switch to “ ” while pressing down
the Lock Button located on the switch, then open
the LCD monitor fully or pull out the viewfinder
fully. The power lamp lights and the camcorder is
turned on.

2

Press the MENU Wheel in. The Menu Screen
appears.

3

Rotate the MENU Wheel to select “ CAMERA”
and press it. The CAMERA Menu appears.

4

Rotate The MENU Wheel to select “REC MODE”
and press it. The Sub Menu appears. Select “SP” or
“LP” by rotating the MENU Wheel and press it.
Rotate the MENU Wheel to select “ RETURN”, and
press it twice. The Menu Screen closes.

•Audio Dubbing (墌 pg. 66) and Insert Editing
(墌 pg. 68) are impossible on a tape recorded in
the LP mode.

•“LP” (Long Play) is more economical, providing

1.5 times the recording time.

NOTES:

●

If the recording mode is switched during recording, the
playback picture will be blurred at the switching point.

●

It is recommended that tapes recorded in the LP mode
on this camcorder be played back on this camcorder.

●

During playback of a tape recorded on another
camcorder, blocks of noise may appear or there may
be momentary pauses in the sound.

Power Switch

Display

CAMERA Menu

Sub Menu

GR-DVM75 only

14 EN

GETTING STARTED

(cont.)

Memory card

Clipped edge

Card Cover

Loading A Memory Card
(GR-DVM75 only)

The provided memory card is already inserted in the
camcorder when you receive the camcorder.

1

Make sure the camcorder’s power is off.

2

Slide CARD OPEN to open the card cover.

3

Insert the memory card firmly clipped edge first.

•Do not touch the terminal on the reverse side of
the label.

4

To close the card cover, push it until you hear a
click.

To Unload A Memory Card . . .

.... in step 3 push the memory card, then the memory

card comes out of the camcorder automatically. Pull
it out and close the card cover.

NOTES:

●

Be sure to use only SD Memory Cards marked “ ”
or MultiMediaCards marked “ ”.

●

Some brands of memory cards are not compatible with
this camcorder. Before purchasing a memory card,
consult its manufacturer or dealer.

●

Before using a new memory card, it is necessary to
FORMAT the card. 墌 pg. 36

ATTENTION:

Do not insert/remove the memory card while the
camcorder is turned on, as this may cause the
memory card to be corrupted or cause the camcorder
to become unable to recognize whether or not the
card is installed.

Label

CARD OPEN

EN15

UXGA

AUTO

GAV

SIZE

–
–

TYQUA L I

– FINE

AUTO–

SIZEIMAGE

–

XGA

VGA

STANDARD

P

L

A

Y

O

F

F

Picture Quality Mode Setting
(GR-DVM75 only)

The Picture Quality mode can be selected to best match
your needs. Two Picture Quality modes are available:
FINE and STANDARD (in order of quality).

1

Set the Power Switch to “ ” while pressing down the
Lock Button located on the switch, then open the LCD
monitor fully or pull out the viewfinder fully. The
power lamp lights and the camcorder is turned on.

2

Press the MENU Wheel in. The Menu Screen
appears.

3

Rotate the MENU Wheel to select “ DSC” and
press it. The DSC Menu appears.

4

Rotate the MENU Wheel to select “QUALITY” and
press it. The Sub Menu appears. Rotate the MENU
Wheel to select the desired mode and press it.
Rotate the MENU Wheel to select “ RETURN”, and
press it twice. The Menu Screen closes.

Display

Image Size Mode Setting
(GR-DVM75 only)

The Image Size mode can be selected to best match your
needs. Two Image Size modes are available: XGA (1024 x
768 pixels) and VGA (640 x 480 pixels) (in order of
quality).

1

Set the Power Switch to “ ” while pressing down the
Lock Button located on the switch, then open the LCD
monitor fully or pull out the viewfinder fully. The
power lamp lights and the camcorder is turned on.

2

Press the MENU Wheel in. The Menu Screen
appears.

3

Rotate the MENU Wheel to select “ DSC” and
press it. The DSC Menu appears.

4

Rotate the MENU Wheel to select “IMAGE SIZE”
and press it. The Sub Menu appears. Rotate the
MENU Wheel to select the desired mode and press
it. Rotate the MENU Wheel to select “ RETURN”,
and press it twice. The Menu Screen closes.

Approximate Number of Storable Images

Image Size/Picture
Quality Mode

Memory Card

8MB*

16MB**

XGA FINE 20 40 90 190

XGA STANDARD 60 140 290 600

VGA FINE 40 100 210 430

VGA STANDARD 130 290 610 1230

DSC Menu

MENU Wheel

Lock Button

Power Switch

NOTES:

●

The number of storable images depends on
the selected picture quality as well as the
composition of the subjects in the images
and the type of memory card being used.

●

In the XGA mode, images are shot in 720 x
480 pixels and they are converted and
stored in the XGA mode file size (1024 x
768 pixels).

●

The number of storable images in the below
chart is approximate value for a memory
card with 12 sound effects pre-stored.

32MB** 64MB**

* Provided with GR-DVM75

only

** Optional

16 EN

P

L

A

Y

O

F

F

Operation Mode

Choose the appropriate operation mode according to
your preference using the Power Switch and VIDEO/DSC
Switch (GR-DVM75 only).

When the Power Switch is set to “ ”,
“ ” appears. When set to “ ” or “ ”,

there is no indication.

To turn on the camcorder, set the Power
Switch to any operation mode except “OFF”
while pressing down the Lock Button located
on the switch.

Power Switch

Lock Button

Power lamp

Power Switch Position

(Manual):

Allows you to set various recording functions using
the Menus. If you want more creative capabilities than
Full Auto recording, try this mode.

(Full Auto):

Allows you to record using NO special effects or
manual adjustments. Suitable for standard recording.

OFF:

Allows you to switch off the camcorder.

:

•Allows you to play back a recording on the tape.

•Allows you to transfer a still image recorded on the

tape to a computer (GR-DVM55 only).

•Allows you to display a still image stored in the
memory card or to transfer a still image stored in the
memory card to a computer (GR-DVM75 only).

VIDEO/DSC Switch Position (GR-DVM75 only)

VIDEO:

Allows you to record on a tape or play back a tape. If
“REC SELECT” is set to “ / ” in the DSC
Menu Screen, still images are also recorded in the
memory card.

:

Allows you to record a still image or display a still
image stored in the memory card.

VIDEO/DSC Switch
(GR-DVM75 only)

When the Power Switch is set to “ ” or

“ ” and the VIDEO/DSC Switch is set to
“ ”, the selected image size (“VGA” or
“XGA”) is displayed. When set to “VIDEO”,

there is no indication. (GR-DVM75 only)

GETTING STARTED

(cont.)

VGA

EN17

VIDEO RECORDING & PLAYBACK

VIDEO RECORDING

&

PLAYBACK

CONTENTS

VIDEO RECORDING

............................................. 18 – 20

Basic Recording

.............................................................. 18

Journalistic Shooting

........................................................ 19

Self-Recording

............................................................... 19

Zooming

...................................................................... 19

Time Code

.................................................................... 20

Recording From The Middle Of A Tape .......................................

20

VIDEO PLAYBACK

............................................... 21 – 24

Normal Playback ........................................................

21

Still Playback ............................................................

21

Shuttle Search ...........................................................

21

Frame-By-Frame Playback .............................................

21

Connections

.......................................................... 22 – 23

Blank Search

................................................................. 24

18 EN

BR I GHT

25

min

90 min

89 min

3 min

2 min

1 min0 min

min

P

L

A

Y

O

F

F

180°

90°

NOTES:

●

The image will not appear simultaneously on the LCD
monitor and the viewfinder.

●

If the Record-Standby mode continues for 5 minutes, the
camcorder’s power shuts off automatically. To turn the
camcorder on again, push back and pull out the
viewfinder again or close and re-open the LCD monitor.

●

When a blank portion is left between recorded scenes
on the tape, the time code is interrupted and errors
may occur when editing the tape. To avoid this, refer to
“Recording From The Middle Of A Tape” (墌 pg. 20).

●

To turn the tally lamp or beep sounds off, 墌 pg. 38,

40.

VIDEO RECORDING

Power Lamp

Recording Start/
Stop Button

Tape remaining
time indicator
(Approximate)

(Now calculating)

(Blinking) (Blinking) (Blinking)

Display

To Adjust The Brightness Of The Display

.... rotate the MENU Wheel until the bright level indicator

on the display moves and the appropriate brightness is
reached.

•It is also possible to adjust the brightness of the viewfinder.

Power Switch

Basic Recording

NOTE:

You should already have performed the procedures listed
below. If not, do so before continuing.

●

Power (墌 pg. 8)

●

Grip Adjustment (墌 pg. 10)

●

Viewfinder Adjustment (墌 pg. 10)

●

Load A Cassette (墌 pg. 12)

●

Recording Mode Setting (墌 pg. 13)

1

Set the VIDEO/DSC Switch to “VIDEO”
(GR-DVM75 only), then set the Power Switch to
“ ” or “ ” while pressing down the Lock Button
located on the switch.

Shooting while using the LCD monitor:

Make sure
the viewfinder is pushed back in. Open the LCD
monitor fully.

Shooting while using the viewfinder:

Make sure the
LCD monitor is closed and locked. Pull out the
viewfinder fully.

•Be sure to pull out the viewfinder until you hear a

click, otherwise it may be pushed back in during
use.

•The Power lamp lights and the camcorder enters the

Record-Standby mode. “PAUSE” is displayed.

2

Press the Recording Start/Stop Button. “ ”
appears while recording is in progress.

To Stop Recording . . .

.... press the Recording Start/Stop Button. The camcorder

re-enters the Record-Standby mode.

MENU Wheel

Lock Button

VIDEO/DSC Switch
(GR-DVM75 only)

Tally lamp
(Lights while
recording is in
progress)

For other notes, 墌 pg. 77

EN19

10xW

T

1xW

T

10xW

T

20xW

T

40xW

T

Journalistic Shooting

In some situations, different shooting angles may
provide more dramatic results. Hold the camcorder
in the desired position and tilt the LCD monitor in
the most convenient direction. It can rotate 270°
(90° downward, 180° upward).

Self-Recording

You can shoot yourself while viewing your own
image in the LCD monitor. Open the LCD monitor
and tilt it upward 180° so that it faces forward, then
point the lens toward yourself and start recording.

Zoom in (T: Telephoto)

Zoom out (W: Wide angle)

Power Zoom
Lever

Zoom display

FEATURE:

Zooming

PURPOSE:

To produce the zoom in/out effect, or an instantaneous
change in image magnification.

OPERATION:

Zoom In

Slide the Power Zoom Lever towards “T”.

Zoom Out

Slide the Power Zoom Lever towards “W”.

䡲 The further you slide the Power Zoom Lever, the

quicker the zoom action.

NOTES:

●

Focusing may become unstable during Zooming. In
this case, set the zoom while in Record-Standby,
lock the focus by using the manual focus
(墌 pg. 51), then zoom in or out in Record mode.

●

Zooming is possible to a maximum of 200X with
GR-DVM75 or 300X with GR-DVM55, or it can be
switched to 10X magnification using the optical
zoom (墌 pg. 39).

●

Zoom magnification of over 10X is done through
Digital image processing, and is therefore called
Digital Zoom.

●

During Digital zoom, the quality of image may
suffer.

●

Digital zoom cannot be used in the following cases:

•

When digital image processing, such as Picture
Wipe/Dissolve (墌 pg. 48, 49) or Video Echo
(墌 pg. 47), is activated.

●

Macro shooting (as close as approx. 5 cm (2") to the
subject) is possible when the Power Zoom Lever is
set all the way to “W”. Also see “TELE MACRO” in
the Menu Screen on page 39.

Approximate zoom ratio

Digital zoom zone

10X (optical) zoom
zone

20 EN

Time Code

During recording, a time code is recorded on the tape. This code is to confirm the location of the recorded
scene on the tape during playback.
If recording starts from a blank portion, the time code begins counting from “00:00:00”
(minute:second:frame). If recording starts from the end of a previously recorded scene, the time code
continues from the last time code number.

To perform Random Assemble Editing (墌 pg. 69 – 73), time code is necessary. If during recording a blank
portion is left partway through the tape, the time code is interrupted. When recording is resumed, the time
code starts counting up again from “00:00:00”. This means the camcorder may record the same time
codes as those existing in a previously recorded scene. To prevent this, perform “Recording From The
Middle of A Tape” below in the following cases;

•When shooting again after playing back a
recorded tape.

•When power shuts off during shooting.

•When a tape is removed and re-inserted during

shooting.

•When shooting using a partially recorded tape.

•When shooting on a blank portion located

partway through the tape.

•When shooting again after shooting a scene
then opening/closing the cassette holder cover.

Recording From The Middle Of A Tape

1. Play back a tape or use Blank Search (墌 pg. 24) to find the spot at which you want to start recording,

then engage the Still Playback mode (墌 pg. 21).

2. Set the Power Switch to “ ” or “ ” while pressing down the Lock Button located on the switch, then

start recording.

NOTES:

●

The time code cannot be reset.

●

During fast-forwarding and rewinding, the time code indication does not move smoothly.

●

The time code is displayed only when “TIME CODE” is set to “ON” (墌 pg. 41, 42).

Shooting start point

Newly recorded sceneBlankAlready recorded scene

Time code
05:43:21

Time code
00:00:00

Tape

Time code
00:00:00

Shooting start pointShooting stop point

12:34:24

Display

When a blank portion is recorded on a tape

Shooting start point

Time code
05:43:21

Time code
05:44:00

Tape

Time code
00:00:00

Shooting start pointShooting start point

Proper recording

Latest sceneNew sceneAlready recorded scene

Frames
(30 frames = 1 second)

Seconds

Minutes

Frames are not displayed
during recording.

VIDEO RECORDING

(cont.)

EN21

P

L

A

Y

O

F

F

VIDEO PLAYBACK

Power Switch

Rewind Button (2)

Fast-Forward Button (3)

Play/Pause Button (4/6)

Stop Button (5)

Normal Playback

1

Load a tape ( pg. 12).

2

Set the VIDEO/DSC Switch to “VIDEO” (GR­DVM75 only), then set the Power Switch to “ ”
while pressing down the Lock Button located on the
switch. To start playback, press 4/6.

•To stop playback, press 5.

•Press 2 to rewind, or 3 to fast-forward the
tape during Stop mode.

To Control The Speaker Volume . . .

.... slide the Power Zoom Lever (Speaker Volume

Control) (VOL.) towards “+” to turn up the volume,
or towards “–” to turn down the volume.

NOTES:

●

If Stop mode continues for 5 minutes when power is supplied
from a battery, the camcorder shuts off automatically. To turn
on again, set the Power Switch to “OFF”, then to “ ”.

●

The playback picture can be viewed in the LCD monitor,
viewfinder or on a connected TV ( pg. 22, 23).

●

You can also view the playback picture on the LCD monitor
with it flipped over and pushed against the camera body.

●

LCD monitor/viewfinder indications:

•

When power is supplied from a battery: the “ ”
battery pack remaining power indicator is displayed.
When power is supplied from an AC outlet: “ ”
does not appear.

•

During Stop mode, none of the indications are displayed.

●

When a cable is connected to the AV connector, the
sound is not heard from the speaker.

Power Zoom
Lever (Speaker
Volume Control)
(VOL.)

Speaker

Lock Button

Still Playback:

Pauses during playback.

1) Press 4/6 during playback.

2) To resume normal playback, press 4/6 again.

●

If still playback continues for more than about 3 minutes, the camcorder’s Stop mode is automatically
engaged. After 5 minutes in the Stop mode, the camcorder’s power is automatically turned off.

●

When

4/6

is pressed, the image may not pause immediately while the camcorder stabilises the still image.

Shuttle Search:

Allows high-speed search in either direction.

1) Press 3 for forward or 2 for reverse search during playback.

2) To resume normal playback, press 4/6.

●

During playback, press and hold

2

or

3

. The search continues as long as you hold the button.

Once you release it, normal playback resumes.

●

A slight mosaic effect appears on screen during Shuttle Search. This is not a malfunction.

Frame-By-Frame Playback: Allows frame-by-frame search.

1) Engage Still Playback.

2) Rotate MENU Wheel towards “+” for forward Frame-By-Frame Playback, or towards “–” for reverse

Frame-By-Frame Playback during Still Playback.

 To resume normal playback, press 4/6.

●

You can also use the provided remote control for Frame-By-Frame Playback ( pg. 64).

Playback Zoom and Playback Special Effects

Available only with the remote control (provided) ( pg. 64, 65).

VIDEO/DSC Switch
(GR-DVM75 only)

22 EN

VIDEO PLAYBACK

(cont.)

Connections

These are some basic types of connections. When making the connections, refer also to your VCR and TV
instruction manuals.

A. Connection to a TV or VCR equipped only with A/V input connectors

B. Connection to a TV or VCR equipped with an S-VIDEO IN and A/V input connectors

White to AUDIO L IN**

To S-VIDEO IN

Red to AUDIO R IN**

Yellow: Not connected

To S-VIDEO

S-Video cable
(optional)

Audio/Video cable

(provided)

TV

* When connecting the cables, open this cover.
** The Audio cable is not required for watching still images only.
*** AV IN/OUT:GR-DVM75, AV OUT:GR-DVM55

To TV or VCR

* When connecting the cables, open this cover.
** The Audio cable is not required for watching still images only.
*** AV IN/OUT:GR-DVM75, AV OUT:GR-DVM55
**** Refer to “Jack Box Attachment” ( pg. 23).

NOTE:

In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or
more core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to
the camcorder.

Jack box****

To AV IN/OUT***
or AV OUT***

Connector cover*

VCR

NOTE:

In order to maintain optimum performance of the camcorder, provided cables may be equipped with one or
more core filter. If a cable has only one core filter, the end that is closest to the filter should be connected to
the camcorder.

TV

Yellow to VIDEO IN

Audio/Video cable
(provided)

Red to
AUDIO R IN**

White to AUDIO L IN**

To
AV IN/OUT*** or
AV OUT***

Connector cover*

To TV or VCR

VCR

EN23

NOTES:

●

It is recommended to use the AC Adapter as the
power supply instead of the battery pack
( pg. 9).

●

The S-Video cable is optional. Be sure to use the
YTU94146A S-Video cable.
Consult the JVC Service Center described on the
sheet included in the package for details on its
availability. Make sure to connect the end with a
core filter to the camcorder. The core filter
reduces interference.

●

To monitor the picture and sound from the
camcorder without inserting a tape or memory
card*, set the camcorder’s Power Switch to “ ”
or “ ”, then set your TV to the appropriate input
mode.
*GR-DVM75 only

●

Make sure you adjust the TV sound volume to its
minimum level to avoid a sudden burst of sound
when the camcorder is turned on.

●

If you have a TV or speakers that are not specially
shielded, do not place the speakers adjacent to
the TV as interference will occur in the camcorder
playback picture.

●

While the Audio/Video cable is connected to the
AV connector, sound cannot be heard from the
speaker.

●

If no image is displayed or no sound is heard from
the TV, set “S/AV INPUT” to “OFF” in the Menu
Screen (GR-DVM75 only,  pg. 42).

1

Make sure all units are turned off.

2

Connect the camcorder to a TV or VCR as
shown in the illustration ( pg. 22).

If using a VCR . . . go to step 3.
If not . . . go to step 4.

3

Connect the VCR output to the TV input,
referring to your VCR’s instruction manual.

4

Turn on the camcorder, the VCR and the TV.

5

Set the VCR to its AUX input mode, and set the
TV to its VIDEO mode.

To choose whether or not the following displays
appear on the connected TV . . .

•Date/Time

.... set “DATE/TIME” to “AUTO”, “ON” or “OFF”

in the Menu Screen ( pg. 42, 43).

•Time Code

.... set “TIME CODE” to “ON” or “OFF” in the

Menu Screen ( pg. 42, 43).

•Playback Sound Mode, Tape Speed And Tape

Running Displays for video playback
Or
Type of file, Directory/File Names and Image

Number/Total Number of Images for D.S.C.
Playback (GR-DVM75 only)

.... set “ON SCREEN” to “LCD” or “LCD/TV” in

the Menu Screen ( pg. 42, 43).
Or, press DISPLAY on the remote control.

Jack Box Attachment

Insert the terminal end 1 of the jack box into the jack box
mount, then firmly push the end 2 of the jack box in the
direction of the arrow until it locks into place as shown in the
illustration.
To detach the jack box, slide the BATT. RELEASE Switch and
detach it.

1

2

BATT. RELEASE
Switch

24 EN

BLANK SEARCH

44

P

L

A

Y

O

F

F

Power Switch

Blank Search

Helps you find where you should start recording in the
middle of a tape to avoid time code interruption
( pg. 20).

1

Load a tape ( pg. 12).

2

Set the VIDEO/DSC Switch to “VIDEO” (GR­DVM75 only), then set the Power Switch to “ ”
while pressing down the Lock Button located on the
switch.

3

Press FOCUS/BLANK.

•“BLANK SEARCH” appears blinking and the
camcorder automatically starts reverse or forward
shuttle search, then stops at the spot which is
about 3 seconds of tape before the beginning of
the detected blank portion.

To cancel Blank Search midway . . .

.... press 5.

NOTES:

●

In step 3, if the current position is at a blank portion the
camcorder searches in the reverse direction, and if the
current position is at a recorded portion the camcorder
searches in the forward direction.

●

Blank Search does not work if “HEAD CLEANING
REQUIRED. USE CLEANING CASSETTE” has appeared
with the tape.

●

If the beginning or end of the tape is reached during
Blank Search, the camcorder stops automatically.

●

A blank portion which is shorter than 5 seconds of tape
may not be detected.

●

The detected blank portion may be located between
recorded scenes. Before you start recording, make sure
there is no recorded scene after the blank portion.

Lock Button

Stop Button (5)

FOCUS/BLANK Button

VIDEO PLAYBACK

(cont.)

VIDEO/DSC Switch
(GR-DVM75 only)

Display

EN25

DIGITAL STILL CAMERA (D.S.C.) RECORDING & PLAYBACK

CONTENTS

D.S.C. RECORDING

.............................................. 26 – 27

Basic Shooting (Snapshot)

......................................... 26 – 27

D.S.C. PLAYBACK

................................................ 28 – 36

Normal Playback (Of Images) ...................................................

28

Auto Playback (Of Images) ......................................................

28

Index Screen

................................................................. 29

Index Playback

.............................................................. 30

Jump Playback

............................................................... 30

Protecting Files

.............................................................. 31

Deleting Files

......................................................... 32 – 33

Setting Print Information (DPOF Setting)

....................... 34 – 35

Initialising A Memory Card

................................................ 36

DIGITAL STILL CAMERA (D.S.C.)

RECORDING

&

PLAYBACK

The D.S.C. (Digital Still Camera) features are available
on GR-DVM75.

26 EN

SNAP MODE –

FULL
MUL T I –

4

MUL T I –

9

PIN–UP

FRAME

P

L

A

Y

O

F

F

D.S.C. RECORDING

Basic Shooting (Snapshot)

You can use your camcorder as a Digital Still Camera for
taking snapshots.

NOTE:

You should already have performed the procedures listed
below. If not, do so before continuing.

●

Power ( pg. 8)

●

Grip Adjustment ( pg. 10)

●

Viewfinder Adjustment ( pg. 10)

●

Loading A Memory Card ( pg. 14)

●

Picture Quality/Image Size Mode Setting ( pg. 15)

SNAPSHOT MODE SELECTION

1

Set the VIDEO/DSC Switch to “ ”, then set the
Power Switch to “ ” while pressing down the Lock
Button located on the switch. Open the LCD
monitor fully or pull out the viewfinder fully.

2

Press the MENU Wheel in. The Menu Screen
appears.

3

Rotate the MENU Wheel to select “ CAMERA”,
then press it. The CAMERA Menu appears.

4

Rotate the MENU Wheel to select “SNAP MODE”,
then press it.

5

Rotate the MENU Wheel to select the desired
Snapshot mode, then press it. Rotate the MENU
Wheel to select “ RETURN” and press it twice. The
Menu Screen closes.

SNAPSHOT RECORDING

1

Press SNAPSHOT. appears while the snapshot
is being taken.
The image is stored in the memory card.

•Regardless of the Power Switch position (“ ” or
“ ”), Snapshot recording takes place using the

selected Snapshot mode.

•To use the flash,  pg. 54.

Power Switch

SNAPSHOT Button

Lock Button

VIDEO/DSC
Switch

FINE

10 / 100

VGA

Number of shots taken

Displays the number of images that have already been shot.

Total number of shots

Displays the approximate total number of shots that can be stored, including
those already taken. The number increases or decreases depending on the shots
stored, the Picture Quality/Image Size mode, etc.

Picture Quality mode

Displays the Picture Quality mode of the stored image. There are 2 modes
available: FINE and STD (Standard) ( pg. 15).

Display

Shooting icon

Appears and blinks during shooting.

Card icon

Appears during shooting and blinks when a memory card is not loaded.

Display

CAMERA Menu

Image Size mode

Displays the Image Size mode of the stored
image. There are 2 modes available: XGA and
VGA ( pg. 15).

EN27

To Delete Unwanted Still Images . . .

.... when unwanted still images are stored in the

memory card or its memory is full, refer to “Deleting
Files” ( pg. 32) and delete unwanted still images.

To Remove The Shutter Sound . . .

.... when you do not want to hear the shutter sound, set

“BEEP” to “OFF” in the Menu Screen ( pg. 38, 40).
The sound is no longer heard from the speaker.

NOTES:

●

Even if “MULTI-4” or “MULTI-9” is engaged, Snapshot
recording will be performed in the FULL mode during
Digital Zoom or Night-Alive ( pg. 45).

●

The image is stored in the VGA mode regardless of the
image size mode setting ( pg. 15) if “MULTI-4” or
“MULTI-9” is engaged.

●

If SNAPSHOT is pressed when “DIS” is set to “ON”
(pg. 39), the Stabiliser will be disabled.

●

If Snapshot recording is not possible, “ ” blinks
when SNAPSHOT is pressed.

●

If Program AE with special effects ( pg. 46) is
engaged, certain modes of Program AE with special
effects are disabled during Snapshot recording. In such
a case, the icon blinks.

●

If shooting is not performed for approx. 5 minutes
when the Power Switch is set to “ ” or “ ” and
power is supplied from the battery pack, the camcorder
shuts off automatically to save power. To perform
shooting again, push back and pull out the viewfinder
again or close and re-open the LCD monitor.

●

The Motor Drive mode ( pg. 50) is disabled when the
VIDEO/DSC Switch is set to “ ”.

●

When a cable is connected to the AV connector, the
shutter sound is not heard from the speaker, however it
is recorded onto the tape.

●

Still images taken are compliant to DCF (Design rules
for Camera File systems). They do not have any
compatibility with devices which are not compliant to
DCF.

●

In the XGA mode, images are shot in 720 x 480 pixels
and they are converted and stored in the XGA mode
file size (1024 x 768 pixels).

FULL
Snapshot mode
with no frame*

PIN-UP
Pin-Up mode*

FRAME
Snapshot mode
with frame*

MULTI-4
Multi-Analyzer 4

* There is the sound effect of a shutter

closing.

MULTI-9
Multi-Analyzer 9

28 EN

P

L

A

Y

O

F

F

10

10

/

24

24

100

100

-

0010

0010

100

100

-

0011

0011

100

100

-

0012

0012

100

100

-

0013

0013

JAN

JAN

10

10

’01

01

11

11

/

24

24

JAN

JAN

10

10

’01

01

12

12

/

24

24

JAN

JAN

10

10

’01

01

13

13

/

24

24

JAN

JAN

10

10

’01

01

D.S.C. PLAYBACK

Power Switch

Normal Playback (Of Images)

Images shot with the camcorder are automatically
numbered, then stored in numerical order in the memory
card. You can view the stored images, one at a time,
much like flipping through a photo album.

1

Load a memory card ( pg. 14).

2

Set the VIDEO/DSC Switch to “ ”, then set the
Power Switch to “ ” while pressing down the
Lock Button. Open the LCD monitor fully or pull out
the viewfinder fully.

•A stored image is displayed.

3

Press 3 to display the next image.
Press 2 to display the previous image.

Auto Playback (Of Images)

You can run through all the images stored in memory
automatically.

1

Perform steps 1 and 2 above.

2

Press 4/6.

•If you press 2 during Auto Playback, images are
displayed in descending order.

•If you press 3 during Auto Playback, images are
displayed in ascending order.

3

To end Auto Playback, press 5.

NOTES:

●

Even if you shoot a new image after playing back a
low-numbered one, this will not overwrite an existing
image, because new images are automatically stored
after the last-recorded one.

●

Images shot in a file size other than VGA/XGA with
devices that are compatible with DCF (Design rules for
Camera File systems) will be displayed as reduced-size
thumbnail images. These thumbnail images cannot be
transferred to a PC.

●

Images shot with devices (such as JVC GR-DVM70)
that are not compatible with DCF cannot be viewed
with this camcorder; “Unsupported file!” will be
displayed.

[For Normal Playback]
To display the next image

Display

[For Auto Playback]

Stop Button (5)

To display the
previous image

Image number

Displays the index
number of the image file
( pg. 29).

Total number of
images

Displays the total
number of stored
images.

Rewind Button (2)

Fast-Forward Button (3)

Directory and File names

Displays the directory and file
names ( pg. 29).

Play Button (4/6)

Lock Button

VIDEO/DSC Switch

Date

Displays the date when the image was shot (if “DATE/TIME”is
set to “ON” in the Menu Screen  pg. 42–43).

EN29

Index Screen

100-DVC00003: Directory and File
names

Shows that the selected file is in a directory
called “100” and its file name is “DVC00003”.
Each time shooting takes place, a file name is
made using a number which is larger by one
than the largest number of the file names
which are in use. If the file name reaches
DVC09999, a new directory will be made and
the file name will start again from DVC00001.
In the playback screen ( pg. 28), the
directory and only the last four digits of the file
name are displayed.
In the Index Screen for sound effects, the name
of the selected sound effect is displayed if the
name is compatible with ID3TAG ver 1 or 2.

To view video clips (pg. 61) stored in a memory card . . .

… during normal playback of image, press SELECT once to

engage the video clip mode. “E-CLIP” appears. Then pressing
4/6 can allow you to view the video clips in the LCD
monitor or viewfinder; video clips cannot be displayed on a
connected TV.

•

You can look for the desired file using Index Screen
(below and pg. 30).

To listen to sound effects (pg. 56) stored in a memory card . . .

… during normal playback of image, press SELECT twice to

engage the sound effect mode. “D.SOUND” appears. Then
pressing D.SOUND PLAY can allow you to listen to the sound
effect.

•

You can look for the desired file using Index Screen
(below and pg. 30).

The files you stored can be displayed together with their
index information. Convenient for checking files stored
beforehand, the Index Screen also shows the Picture
Quality, Image Size mode, directory and file names as well
as which files are protected against accidental erasure. To
display the Index Screen,  pg. 30.

IMAGE/E-CLIP/SOUND: Type of File

Displays the type of file of the displayed index screen.
There are 3 types available: IMAGE for still images,
E-CLIP for video clips ( pg. 61), SOUND for sound
effects ( pg. 56, 67).

1: Index number

Index numbers are marked from 1. For example, when
10 files are stored (index number: 1 to 10), if three files
with index numbers 2, 4 and 6 are deleted from memory,
the remaining files are automatically moved up to fill any
gaps in the numerical sequence. Therefore, the number
of remaining files is 7, and the new index numbers range
from 1 to 7.

F/S: Picture Quality

Displays the Picture Quality mode of the stored image.
There are 2 modes available: FINE and STANDARD (in
order of quality) ( pg. 15). (Appears only when
displaying still images.)

VGA/XGA: Image Size

Displays the size of the stored image. There are 2 modes
available: VGA and XGA ( pg. 15). (Appears only when
displaying still images.)

: Protect icon

When a file is protected against its accidental erasure, a
padlock mark appears next to the index number, and that
file cannot be deleted.

Selected File

A file is framed in green when it is selected. Rotate the
MENU Wheel to move the green frame to the desired file.

E - C L I P

3 / 4

D . SOUN

D

EX

PL1O/S

I

1O2

N

Index number

Selected file

Picture

Quality

Directory and File
names

Type of file

Image Size

Protect icon

VGA

1 F 2 S

3 S

5 F

4 F

EXIT

100-DVC00003

6 F

IMAGE

VGA

Total number
of files

File (index) number

Selected sound effect name

30 EN

F

S

FS

FF

1 2

3

5

4

EXIT

100-DVC00001 VGA

6

IMAGE

F

S

FS

FF

1 2

3

5

4

EXIT

100-DVC00001

6

E-CLIP

F

S

FS

FF

1 2

3

5

4

EXIT

EXPLOSION

6

SOUND

SCEALNECCETL/SET

[
[

MJEUNMU

P

]
]

10 / 50

JUMP MENU

Index Screen
for images

Index Playback

You can view or listen to the files (still images, video clips
( pg. 61), or sound effects ( pg. 56, 67)) stored in
memory six at a time. Use this mode when looking for a
file you wish to view or hear.

1

Perform steps 1 and 2 of “Normal Playback” on
pg. 28.

2

To display the Index Screen . . .

… for images, go to step 3.
… for video clips ( pg. 61), press SELECT once to

engage the video clip mode. “E-CLIP” appears.
Then go to step 3.

… for sound effects ( pg. 56), press SELECT twice

to engage the sound effect mode. “D.SOUND”
appears. Then go to step 3.

3

Press INDEX. The Index Screen appears.

4

Rotate the MENU Wheel to move the green frame to
the desired file and press it. The file selected in the
Index Screen is displayed or played back.

•To start playback of the selected video clip, press
4/6. To stop playback midway, press 5.

•To start playback of the selected sound effect, press

D.SOUND PLAY.

INDEX Button

SELECT
Button

D.S.C. PLAYBACK

(cont.)

MENU
Wheel

Display

JUMP Button

Jump Screen

Jump Playback

You can call up directly a file you want to play back by
specifying its index number.

1

During normal playback of images, press SELECT
repeatedly to select the type of file you want to play
back.

2

Press JUMP. The Jump Screen appears.

3

Rotate the MENU Wheel to enter the index number
of the desired file and press it.

•The file for the selected index number is displayed.

•To cancel the Jump Playback while the Jump

Screen is being displayed, press JUMP again.

Index Screen
for video clips

Index Screen
for sound
effects

Total number
of files

Index number