JVC GET0632-001A, KD-R418 User Manual

KD-R418

CD RECEIVER : INSTRUCTIONS/INSTALLATION

Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

For customer Use:

Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference. Model No. Serial No.

1009DTSMDTJEIN

Canceling the display demonstration

1 Turn on the power.

[Hold]

(Initial setting)

4 Select <DEMO OFF>.

6 Finish the procedure.

GET0632-001A

[J]

INFORMATION (For U.S.A.)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help.

Caution:

Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all

3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. (For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

servicing to qualified service personnel.

with optical instruments.

For safety...

[European Union only]

Warning:

If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident.

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

Setting the clock

1 Turn on the power.

[Hold]

(Initial setting)

3 Select <CLOCK>.

4 Select <CLOCK SET>.

Preparations

How to attach/detach the control panel

How to reset your unit

Reset the unit after installation is completed.

• Your preset adjustments will also be erased.

How to forcibly eject a disc

[Hold]

• You can forcibly eject the loaded disc even if the disc is locked. To lock/unlock the disc, see page 2.

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

Preparing the remote controller (RM-RK50)

When you use the remote controller for the first time, pull out the insulation sheet.

Insulation sheet

5 Adjust the hour.

6 Adjust the minute.

7 Finish the procedure.

If the effectiveness of the remote controller decreases, replace the battery.

Replacing the lithium coin battery

CR2025

For USA-California Only: This product contains a CR Coin Cell Lithium Battery which contains Perchlorate Material—special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate

Caution:

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

Warning (about battery handling)

To prevent accidents and damage:

• Do not install any battery other than CR2025 or its equivalent.

• Store out of reach of children.

• Do not recharge, short, or dismantle.

• Do not dispose of in fire.

• Do not carry around with other metallic materials.

• Wrap the battery with tape and insulate when throwing away or saving it.

Basic operations

Ejects the disc

Detaches the panel

Returns to the previous menu

• DO NOT expose to bright sunlight.

When you press or hold the following button(s)...

Main unit

Control dial

Remote sensor

Remote

controller

Turns on.

• When the power is on, pressing also attenuates the sound or pauses. Press muting or resume playback.

Turns off if pressed and held.

Selects the available sources (if the power is turned on).

• If the source is ready, playback also starts.

Adjusts the volume level.

— Selects items.

• Mutes the sound while listening to a source. If the source is “CD” or

—

— Enters playback mode menu directly (see page 2).

—

“USB,” playback pauses. Press the control dial again to cancel muting or resume playback.

• Confirms selection.

Selects the sound mode.

• Enters tone level adjustment directly (see page 3) if pressed and held

EQ BASS-TRE on the main unit.

Power off : Checks the current clock time. Power on : Changes the display information.

Loading slot

Display window

Auxiliary input jack

USB (Universal Serial Bus) input jack

General operations

/I/ATT on the remote controller

/I/ATT again to cancel

Listening to the radio

Listening to the disc

]

“FM” or “AM”

“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.

Manual search

“M” flashes, then press the

[Hold]

button repeatedly.

When an FM stereo broadcast is hard to receive

[Hold]

]

<TUNER> ] <MONO> ] <MONO ON> Reception improves, but stereo effect will be lost.

To restore the stereo effect, repeat the same procedure to select <MONO OFF>.

Automatic presetting (FM)—

SSM (Strong-station Sequential Memory)

You can preset up to 18 stations for FM.

While listening to a station...

[Hold]

] <TUNER> ] <SSM> ] <SSM 01 – 06> / <SSM 07 – 12> / <SSM 13 – 18> “SSM” flashes and local stations with the strongest signals are searched and stored automatically.

To preset another 6 stations, repeat the above procedure by selecting one of the other six SSM setting ranges.

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and 6 stations for AM.

Ex.: Storing FM station of 92.50 MHz into preset number “04.”

]

“92.50MHz”

“PRESET MODE” flashes.

[Hold]

]

Selects preset number “04.”

“P04” flashes and “MEMORY” appears.

Selecting a preset station

Assigning title to a station

You can assign titles to 30 station frequencies (FM and AM) using 8 characters (maximum) for each title.

]

“FM” or “AM”

]

Show the title entry screen.

[Hold]

]

Selects a character.

]

Move to the next (or previous) character

position.

Repeat steps 3 and 4 until you finish entering

the title.

To erase the entire title, press and hold step 2, then press the control dial.

Available characters

ABCDEFGHI

J K LMNOPQR STUVWXYZ0 123456789

—/ <> Space

Changing the display information

Station name * = Frequency = Clock = (back to the beginning)

* If no title is assigned to a station, “NO NAME” appears

for a few seconds.

DISP

after

Using the remote controller

5 U

/ D ∞: Changes the preset stations

2 R

/ F 3: Searches for stations

]

Turn on the power.

Stopping playback and ejecting the disc

“NO DISC” appears. Press

/ SOURCE

playback source.

All tracks will be played repeatedly until you change the source or eject the disc.

to listen to another

Selecting the playback modes

You can use only one of the following playback modes at a time.

Prohibiting disc ejection

[Hold]

To cancel the prohibition, repeat the same procedure.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

Selects folder of the MP3/ WMA

Selects track

Fast-forwards or reverses

[Hold]

the track

Selecting a track/folder

For MP3/WMA discs, select the desired folder, then the desired track by repeating step 2.

• To return to the previous menu, press

BACK

To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”

Changing the display information

Disc title/Album name/performer (folder name)*

number with the elapsed playing time = Current track number with the clock time = (back to the

beginning)

* If the current disc is an audio CD, “NO NAME” appears. If an MP3/WMA file does not have Tag information

Using the remote controller

Listening to the USB device

This unit can play MP3/WMA tracks stored in a USB device.

]

Turn on the power.

USB input jack

]

“REPEAT” j “RANDOM”

REPEAT TRACK RPT FOLDER RPT

RANDOM FOLDER RND

ALL RND

Track title (file name)* = Current track

or <TAG DISPLAY> is set to <TAG OFF> (see page 3), folder name and file name appear.

: Repeats current track : Repeats current folder

: Randomly plays all tracks of

current folder, then tracks of next folders

: Randomly plays all tracks

5 U

/ D ∞: Selects folder of the MP3/

WMA

2 R

/ F 3: Selects track

2 R

/ F

: Fast-forwards or reverses the

[Hold]

track

USB memory

Listening to the external components

You can connect an external component to the AUX (auxiliary) input jack on the control panel.

• Make sure <AUX ON> is selected for the <SRC SELECT>

]

Turn on the connected component and start

playing the source.

“AUX IN”

<AUX IN> setting on page 3.

Portable audio player,

etc.

3.5 mm (3/16”) stereo mini plug (not supplied)

All tracks will be played repeatedly until you change the source or detach the USB device.

If a USB device has been attached...

Pressing starts from where it has been stopped previously.

• If a different USB device is currently attached,

Stopping playback

/ SOURCE

turns on the power and playback

playback starts from the beginning.

and detaching the

USB device

Straightly pull it out from the unit. “NO USB” appears. Press another playback source.

You can operate the USB device in the same way you operate the files on a disc.

Caution on volume setting:

USB devices produce very little noise compared with other sources. Lower the volume before playing a USB to avoid damaging the speakers by sudden increase of the output level.

/ SOURCE

to listen to

Cautions:

• Avoid using the USB device if it might hinder your safety driving.

• Do not pull out and attach the USB device repeatedly while “READING” is shown on the display.

• Do not start the car engine if a USB device is connected.

• This unit may not be able to play the files depending on the type of USB device.

• Operation and power supply may not work as intended for some USB devices.

• You cannot connect a computer to the USB input terminal of the unit.

• Make sure all important data has been backed up to avoid losing the data.

• Do not leave a USB device in the car, expose to direct sunlight, or high temperature to avoid deformation or cause damages to the device.

• Some USB devices may not work immediately after attaching USB device or turn on the power.

• For more details about USB operations, see page 5.

+ 4 hidden pages