JVC GET0564-006A, GET0564-010A, GET0564-001A, GET0568-003A, GET0568-010A Instruction Manual

...

CD RECEIVER

RÉCEPTEUR CD

KD-R303/KD-R302/KD-R301

ENGLISHFRANÇAIS

For canceling the display demonstration, see page 6. Pour annuler la démonstration des affichages, référez-vous à la page 6.

For installation and connections, refer to the separate manual. Pour l’installation et les raccordements, se référer au manuel séparé.

INSTRUCTIONS

MANUEL D’INSTRUCTIONS

GET0568-003A

[EX/EU]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

ENGLISH

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

Battery

Products

Information for Users on Disposal of Old Equipment and Batteries [European Union only]

These symbols indicate that the product and the battery with this symbol should not be disposed as general household waste at its end-of-life. If you wish to dispose of this product and the battery, please do so in accordance with applicable national legislation or other rules in your country and municipality. By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health.

Notice:

The sign Pb below the symbol for batteries indicates that this battery contains lead.

If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

How to reset your unit

• Your preset adjustments will also be erased.

How to forcibly eject a disc

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

CONTENTS

OPERATIONS

Basic operations ........................................... 4

Preparation .................................................. 6

Listening to the radio ................................... 7

Disc operations ............................................. 10

EXTERNAL DEVICES

Listening to the other external

components .............................................. 11

SETTINGS

Selecting a preset sound mode .................... 12

Menu operations .......................................... 13

REFERENCES

ENGLISH

Detaching the control panel

Attaching the control panel

More about this unit .................................... 15

Troubleshooting ........................................... 17

Maintenance ................................................ 19

Specifications ............................................... 20

Basic operations

ENGLISH

1 • FM/AM: Select preset station.

• CD: Select folder.

2 • Turn on the power.

• Attenuate the sound (if the power is on).

• Turn off the power [Hold].

3 Select the source.

FM = CD *1 = AUX IN *2 = AM *2 = (back to

the beginning)

4 • Enter list operations.

• Enter Menu setting [Hold] .

5 • Control the volume or selection [Turn]. *

• Confirm the selection [Press] . *

• FM: Enter SSM preset mode [Hold] . *

• CD: Enter playback mode [Hold] . *

6 Loading slot 7 Display window

8 Eject disc. 9 • Activate/deactivate TA Standby Reception.

• Enter PTY Searching mode [Hold].

p Detach the panel. q Change the display information. w • FM/AM: Search for station.

• CD: Select track.

e Return to the previous menu. r AUX (auxiliary) input jack

*1 You cannot select “CD” as the playback source if no

disc is in the unit.

*2 You cannot select these sources if they were disabled

in the Menu (see “Menu operations” on page 15).

*3 Also known as “Control dial” in this manual.

Display window

ENGLISH

1 Tr (track) indicator 2 Source display / Track number / Folder number /

Time countdown indicator

3 DISC indicator 4 Sound mode indicators—CLASSIC, HIP HOP, JAZZ,

ROCK, POPS, USER

5 Playback mode / item indicators— RND (random),

(disc), (folder), RPT (repeat)

6 EQ (equalizer) indicator

7 LOUD (loudness) indicator 8 Disc information indicators—

TAG (Tag information), (track/file), (folder)

9 Main display p Radio Data System indicators—AF, REG, TP, PTY q Tuner reception indicators—ST (stereo),

MO (monaural)

5OPERATIONS

Preparation

Cancel the display demonstration and set the clock

• See also page 13.

ENGLISH

Turn on the power.

Cancel the display demonstrations

Select “DEMO,” then “DEMO OFF.”

Set the clock

Select “CLOCK” = “CLOCK SET.” Adjust the hour, then press control dial once to proceed to adjust

[Turn] = [Press]

When the power is turned off: Check the current clock time when “CLOCK DISP” is set to “CLOCK OFF,” (see page 13) When the power is turned on: Change the display information of the current source

FM/AM Station Frequency

FM Radio Data System

CD Audio CD/CD Text: Disc title/performer *

Station name (PS) beginning)

MP3/WMA: Album name/performer (folder name) *2 = Track title (file name) *2 =

= Clock = (back to the beginning)

= Station Frequency = Programme type (PTY) = Clock = (back to the

elapsed playing time = Current track number with the clock time = (back to the beginning)

Current track number with the elapsed playing time = Current track number with the clock time = (back to the beginning)

the minute.

Select “24H/12H,” then “24 HOUR” or “12 HOUR.”

• To return to the previous menu, press BACK.

= Track title *1 = Current track number with the

If the current disc is an audio CD, “NO NAME” appears.

If an MP3/WMA file does not have Tag information or “TAG DISPLAY” is set to “TAG OFF” (see page 13),

folder name and file name appear.

Listening to the radio

1 2

Select “FM” or “AM.”

Search for a station to listen—Auto Search.

Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.

• When receiving an FM stereo broadcast with sufficient signal strength, “ST” lights up on the display.

When an FM stereo broadcast is

hard to receive

• See also page 14.

[Turn] = [Press]

ENGLISH

2 Select the preset number range you want to

store.

Select “TUNER” = “MONO”

= “MONO ON”

Reception improves, but stereo effect will be lost.

• “MO” lights up on the display.

To restore the stereo effect, repeat the same procedure to select “MONO OFF.” The MO indicator goes off.

FM station automatic presetting

— SSM (Strong-station Sequential Memory)

You can preset up to 18 stations for FM.

1 While listening to a station...

Local FM stations with the strongest signals are searched and stored automatically.

To preset other 6 stations, repeat from step 1 again.

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and 6 stations for AM. Ex.: Storing FM station of 92.50 MHz into preset

number “04.”

2 Select preset number “04.”

Continued on the next page

7OPERATIONS

3 Start searching for your favorite programme.

ENGLISH

Selecting preset station

[Turn] = [Press]

The following features are available only for FM Radio Data System stations.

Searching for FM Radio Data

System programme — PTY Search

You can tune in to a station broadcasting your favorite programme by searching for a PTY code.

1 The last selected PTY code

appears.

2 Select one of your favorite programme types

or a PTY code.

If a station is broadcasting a programme of the

same PTY code as you have selected, that station is tuned in.

Using the standby receptions

TA Standby Reception

TA Standby Reception allows the unit to switch temporarily to Traffic Announcement (TA) from any source other than AM. The volume changes to the preset TA volume level if the current level is lower than the preset level (see page 14).

To activate TA Standby Reception

The TP (Traffic Programme)

indicator either lights up or flashes.

• If the TP indicator lights up, TA Standby Reception is activated.

• If the TP indicator flashes, TA Standby Reception is not yet activated. (This occurs when you are listening to an FM station without the Radio Data System signals required for TA Standby Reception.)

To activate the reception, tune in to another station

providing these signals. The TP indicator will stop flashing and remain lit.

To deactivate the TA Standby Reception

The TP indicator goes off.

PTY Standby Reception

PTY Standby Reception allows the unit to switch temporarily to your favorite PTY programme from any source other than AM.

To activate and select your favorite PTY code for PTY Standby Reception, see page 14.

The PTY indicator either lights up or flashes.

• If the PTY indicator lights up, PTY Standby Reception is activated.

• If the PTY indicator flashes, PTY Standby Reception is not yet activated.

To activate the reception, tune in to another station

providing these signals. The PTY indicator will stop flashing and remain lit.

Automatic station selection—

Programme Search

Usually when you select a preset number, the station preset in that number is tuned in. If the signals from the FM Radio Data System preset station are not sufficient for good reception, this unit, using the AF data, tunes in to another frequency possibly broadcasting the same programme as the original preset station is broadcasting.

• The unit takes some time to tune in to another station using programme search.

• See also page 14.

PTY codes

ENGLISH

To deactivate the PTY Standby Reception, select “PTY OFF” for the PTY code (see page 14). The PTY indicator goes off.

Tracing the same programme—

Network-Tracking Reception

When driving in an area where FM reception is not sufficient enough, this unit automatically tunes in to another FM Radio Data System station of the same network, possibly broadcasting the same programme with stronger signals (see the illustration below).

Programme A broadcasting on different frequency areas (01 – 05)

NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA, CULTURE, SCIENCE, VARIED, POP M (music), ROCK M (music), EASY M (music), LIGHT M (music), CLASSICS, OTHER M (music), WEATHER, FINANCE, CHILDREN, SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ, COUNTRY, NATION M (music), OLDIES, FOLK M (music), DOCUMENT

When shipped from the factory, Network-Tracking Reception is activated.

To change the Network-Tracking Reception setting, see “AF-REG” on page 14.

9OPERATIONS

Disc operations

ENGLISH

Stop playing and ejecting the disc

• “NO DISC” appears. Press SRC to listen to another playback source.

Prohibiting disc ejection

Turn on the power.

Insert a disc.

All tracks will be played repeatedly until you change the source or eject the disc.

Pressing (or holding) the following buttons allows you to...

MP3/WMA: Select folder

[Press] Select track [Hold] Reverse/fast-forward track

To cancel the prohibition, repeat the same procedure.

Selecting a track/folder

[Turn] = [Press]

• For MP3/WMA discs, select the desired folder, then the desired track by performing the control dial.

• To return to the previous menu, press BACK.

OPERATIONS

Selecting the playback modes

You can use only one of the following playback modes at a time.

[Turn] = [Press]

REPEAT Ô RANDOM

[Turn] = [Press]

REPEAT

TRACK RPT : Repeats current track

FOLDER RPT : MP3/WMA: Repeats current folder

RANDOM

FOLDER RND : MP3/WMA: Randomly plays all

tracks of current folder, then tracks of next folders

ALL RND : Randomly plays all tracks

• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”

• To return to the previous menu, press BACK.

ENGLISH

Listening to the other external components

You can connect an external component to AUX (auxiliary) input jack on the control panel. Preparation: Make sure “AUX ON” is selected in the “SRC SELECT” = “AUX IN” setting, see page 15.

1 2

—

Connecting an external component to the AUX input jack

—

Select “AUX IN.”

Turn on the connected component and start playing the source.

Adjust the volume.

You can adjust the auxiliary input level to avoid the sudden increase of the output level (see “AUX ADJUST” on page 14).

Adjust the sound as you want (see page 12).

3.5 mm stereo mini plug (not supplied)

OPERATIONS & EXTERNAL DEVICES

Portable audio player, etc.

Selecting a preset sound mode

You can select a preset sound mode suitable to the music genre.

• See also page 13 (“EQ”).

ENGLISH

[Turn] = [Press]

Select “EQ”

Preset value setting for each sound mode

Preset values

Indication (For)

BASS

TREBLE

LOUD

Storing your own sound mode

You can store your own adjustments in memory.

1 Select “USER” for “EQ.”

[Turn] = [Press]

Select “EQ”

= “USER”

2 While “USER” is shown on the display...

USER (Flat sound) 00 00 OFF

ROCK (Rock or disco music) +03 +01 ON

CLASSIC (Classical music) +01 –02 OFF

POPS (Light music) +04 +01 OFF

HIP HOP (Funk or rap music) +02 00 ON

JAZZ (Jazz music) +02 +03 OFF

• If no operation is done for about 30 seconds, the operation will be canceled.

3 Select a tone.

[Turn] = [Press]

BASS Ô TREBLE

4 Adjust the level.

Tone Level

BASS –06 to +06

TREBLE –06 to +06

• To return to the previous menu, press BACK.

5 Finish the procedure.

Menu operations

1 2 3 Repeat step 2 if necessary.

[Turn] = [Press]

Category Menu items Selectable settings, [reference page]

• To return to the previous menu, press BACK.

Initial: Underlined

ENGLISH

DEMO

Display

DEMO

demonstration

CLOCK DISP *

Clock display

CLOCK SET

Clock setting

CLOCK

24H/12H

Time display mode

CLOCK ADJ *

Clock adjustment

Equalizer

DIMMER

Dimmer

• DEMO ON

: Display demonstration will be activated automatically if no

operation is done for about 20 seconds, [6].

• DEMO OFF

• CLOCK ON

: Cancels.

: Clock time is shown on the display at all times when the

power is turned off.

• CLOCK OFF

: Cancels; pressing DISP will show the clock time for about 5

seconds when the power is turned off, [6].

: Adjust the hour, then the minute, [6]. [Initial: 0:00]

• 24 HOUR

: See also page 6 for setting.

• 12 HOUR

• AUTO

: The built-in clock is automatically adjusted using the CT

(clock time) data in the Radio Data System signal.

• OFF

: Cancels.

: Select a preset sound mode suitable to the music genre. USER, ROCK, CLASSIC, POPS, HIP HOP, JAZZ

• DIMMER ON

• DIMMER OFF

: Dims the display and button illumination. : Cancels.

SCROLL*

Scroll

DISPLAY

TAG DISPLAY

Tag display

If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select

“CLOCK OFF” to save the car’s battery. *2 Takes effect only when CT (clock time) data is received. *3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.

• SCROLL ONCE

• SCROLL AUTO

• SCROLL OFF

: Scrolls the displayed information once. : Repeats scrolling (at 5-second intervals).

: Cancels. Pressing DISP for more than one second can scroll the display regardless of the setting.

• TAG ON

: Shows the Tag information while playing MP3/WMA

tracks.

• TAG OFF

: Cancels.

Continued on the next page

SETTINGS

Category Menu items Selectable settings, [reference page]

ENGLISH

TUNER

AF-REG *

Alternative frequency/ regionalization reception

PTY-STANDBY *

PTY standby

TA VOLUME *

Traffic announcement volume

P-SEARCH *

Programme search

• AF ON

• AF-REG ON

• OFF

PTY OFF, PTY codes

VOLUME 00

– VOLUME 50 (or VOLUME 00 – VOLUME 30)*

• SEARCH ON

• SEARCH OFF

: When the currently received signals become weak, the unit

switches to another station (the programme may differ from the one currently received), [9].

• The AF indicator lights up. : When the currently received signals become weak, the

unit switches to another station broadcasting the same programme.

• The AF and REG indicators light up. : Cancels.

Activates PTY Standby Reception with one of the PTY codes, [9].

Initial: VOLUME 15

: Activates Programme Search, [9]. : Cancels.

MONO *

Monaural mode

IF BAND

Intermediate frequency band

FADER*

Fader

BALANCE Balance

LOUD

Loudness

AUDIO

AUX ADJUST

Auxiliary input level adjustment

• MONO ON

: Activate monaural mode to improve FM reception, but

stereo effect will be lost, [7].

• MONO OFF

• AUTO

: Restore the stereo effect.

: Increases the tuner selectivity to reduce interference noises

between adjacent stations. (Stereo effect may be lost.)

• WIDE

: Subject to interference noises from adjacent stations, but

sound quality will not be degraded and the stereo effect will remain.

R06 – F06 : Adjust the front and rear speaker output balance.

[Initial: 00]

L06 – R06 : Adjust the left and right speaker output balance.

[Initial: 00]

• LOUD OFF

• LOUD ON

: Cancels. : Boost low and high frequencies to produce a well-balanced

sound at a low volume level.

AUX ADJ 00 — AUX ADJ 05

: Adjust the auxiliary input level to avoid the sudden

increase of the output level when changing the source to external component connected to the AUX input jack on the control panel.

Only for FM Radio Data System stations.

Depends on the amplifier gain control.

*6 Displayed only when the source is “FM.”

If you are using a two-speaker system, set the fader level to “00.”

SETTINGS

Category Menu items Selectable settings, [reference page]

BEEP

Keypress tone

TEL MUTING

Telephone muting

AUDIO

AMP GAIN *

Amplifier gain control

AM *

AM station

AUX IN *

SRC SELECT

Auxiliary input

The volume level automatically changes to “VOLUME 30” if you change to “LOW POWER” with the volume level

set higher than “VOLUME 30.”

*9 Displayed only when any source other than “AM” is selected. *10 Displayed only when any source other than “AUX IN” is selected.

• BEEP OFF

• BEEP ON

• MUTING 1/

• MUTING OFF

• LOW POWER

• HIGH POWER

• AM OFF

• AM ON

• AUX OFF

• AUX ON

MUTING 2

: Deactivates the keypress tone. : Activates the keypress tone.

: Select either one which mutes the sounds while using a

cellular phone.

: Cancels.

: VOLUME 00 – VOLUME 30 (Select if the maximum power

of each speaker is less than 50 W to prevent damaging the speaker.)

: VOLUME 00 – VOLUME 50

: Disable “AM” in source selection. : Enable “AM” in source selection, [4].

: Disable “AUX IN” in source selection. : Enable “AUX IN” in source selection, [4].

ENGLISH

More about this unit

Basic operations

Turning on the power

• By pressing SRC button on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power.

General

• If you change the source while listening to a disc, playback stops.

Next time you select “CD” as the playback source,

playback will start from where it had been stopped previously.

• After ejecting a disc, “NO DISC” appears and you cannot operate some of the buttons. Insert another disc or press SRC to select another playback source.

• If no operation is done for about 30 seconds after pressing MENU button, the operation will be canceled.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and the

stations are stored anew.

– When SSM is over, the station stored in the lowest

preset number will be automatically tuned in.

• When storing a station manually, the previously preset station is erased when a new station is stored in the same preset number.

SETTINGS & REFERENCES

FM Radio Data System operations

• Network-Tracking Reception requires two types of Radio Data System signals—PI (Programme Identification) and AF (Alternative Frequency) to work correctly. Without receiving these data

ENGLISH

correctly, Network-Tracking Reception will not operate correctly.

• If a Traffic Announcement is received by TA Standby Reception, the volume level automatically changes to the preset level (TA VOL) if the current level is lower than the preset level.

• When Alternative Frequency Reception is activated (with AF selected), Network-Tracking Reception is also activated automatically. On the other hand, Network-Tracking Reception cannot be deactivated without deactivating Alternative Frequency Reception. (See page 14.)

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, or for the following reasons:

– Discs are dirty or scratched. – Moisture condensation has occurred on the lens

inside the unit. – The pickup lens inside the unit is dirty. – The files on the CD-R/CD-RW are written using the

“Packet Write” method. – There are improper recording conditions (missing

data, etc.) or media conditions (stained, scratched,

warped, etc.).

• CD-RWs may require a longer readout time since the

reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or a protective seal stuck

to the surface. – Discs on which labels can be directly printed by an

ink jet printer. Using these discs under high temperature or high

humidity may cause malfunctions or damage to the unit.

General

• This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA), MP3/WMA formats.

• When a disc is inserted upside down, “PLEASE” and “EJECT” appear alternately on the display. Press 0 to eject the disc.

• MP3 and WMA “tracks” (words “file” and “track” are used interchangeably) are recorded in “folders.”

• While fast-forwarding or reversing on an MP3 or WMA disc, you can only hear intermittent sounds.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can only play back files of the same type as those detected first if a disc includes both audio CD (CD-DA) files and MP3/WMA files.

Playing an MP3/WMA disc

• This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

• This unit can show the names of albums, artists (performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or

2.4) for MP3 files and for WMA files.

• This unit can display only one-byte characters. No other characters can be correctly displayed.

• This unit can play back MP3/WMA files meeting the conditions below:

– Bit rate: 8 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) – Disc format: ISO 9660 Level 1/Level 2, Romeo,

Joliet, Windows long file name

• The maximum number of characters for file/folder names vary depending on the disc format used (includes 4 extension characters—<.mp3> or <.wma>).

– ISO 9660 Level 1: up to 12 characters – ISO 9660 Level 2: up to 31 characters – Romeo: up to 128 characters – Joliet: up to 64 characters – Windows long file name: up to 128 characters

• This unit can recognize a total of 512 files, 255 folders, and 8 hierarchical levels.

• This unit can play back files recorded in VBR (variable bit rate).

Files recorded in VBR have a discrepancy in the

elapsed time display, and do not show the actual elapsed time. In particular, this difference becomes noticeable after performing the search function.

• This unit cannot play back the following files:

– MP3 files encoded in MP3i and MP3 PRO format. – MP3 files encoded in an inappropriate format. – MP3 files encoded with Layer 1/2.

– WMA files encoded in lossless, professional, and

voice format.

– WMA files which are not based upon Windows

Media ® Audio. – WMA files copy-protected with DRM. – Files which have data such as AIFF, ATRAC3, etc.

• The search function works but search speed is not

constant.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds,

it is automatically inserted into the loading slot again to protect it from dust. Playback starts automatically.

Menu operations

• If you change the “AMP GAIN” setting from

“HIGH POWER” to “LOW POWER” while the volume level is set higher than “VOLUME 30,” the unit automatically changes the volume level to “VOLUME 30.”

ENGLISH

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Check the cords and connections.

• The unit does not work at all. Reset the unit (see page 3).

General

• “AUX IN” cannot be selected. Check the “SRC SELECT” page 15).

• SSM automatic presetting does not work. Store stations manually.

• Static noise while listening to the radio. Connect the aerial firmly.

FM/AM

• “AM” cannot be selected. Check the “SRC SELECT” page 15).

= “AUX IN” setting (see

= “AM” setting (see

Continued on the next page

REFERENCES

Symptoms Remedies/Causes

• Disc cannot be played back. Insert the disc correctly.

ENGLISH

Disc playback

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be skipped.

• Insert a finalized CD-R/CD-RW.

• Finalize the CD-R/CD-RW with the component which you used for recording.

• Disc can neither be played back nor ejected. • Unlock the disc (see page 10).

• Eject the disc forcibly (see page 3).

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

• Change the disc.

• Check the cords and connections.

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• “PLEASE” and “EJECT“ appear alternately

Press

0, then insert a disc correctly.

on the display.

• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file names.

• Noise is generated. Skip to another track or change the disc. (Do not add the extension code <.mp3> or <.wma> to non-MP3 or WMA tracks.)

• A longer readout time is required

Do not use too many hierarchical levels and folders.

(“READING” keeps flashing on the display).

MP3/WMA playback

• Tracks do not play back in the order you

have intended them to play.

The playback order is determined when the files are recorded.

• The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by how the tracks are recorded on the disc.

• The correct characters are not displayed

(e.g. album name).

This unit can only display letters (upper case), numbers, and a limited number of symbols.

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Maintenance

How to clean the connectors

Frequent detachment will deteriorate the connectors. To minimize this possibility, periodically wipe the connectors with a cotton swab or cloth moistened with alcohol, being careful not to damage the connectors.

Connectors

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture has evaporated.

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs

New discs may have some rough spots around the inner and outer edges. If such a disc is used, this unit may reject the disc. To remove these rough spots, rub the edges with a pencil or ball-point pen, etc.

Do not use the following discs:

Single CD (8 cm disc) Warped disc

ENGLISH

How to handle discs

When removing a disc from its case, press down the center holder

of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc in its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs in cases after use.

Center holder

Sticker and sticker residue Stick-on label

C-thru Disc (semi-

Unusual shape

Transparent or semi-

transparent parts on its

recording area

transparent disc)

19REFERENCES

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output: Front/Rear: 50 W per channel

ENGLISH

Continuous Power Output (RMS): Front/Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz

at no more than 0.8% total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)

Tone Control Range: Bass: ±12 dB at 100 Hz

Treble: ±12 dB at 10 kHz

Frequency Response: 40 Hz to 20 000 Hz

Line-Out Level/Impedance: 2.5 V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

Other Terminal: AUX (auxiliary) input jack

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 108.0 MHz

AM: MW: 522 kHz to 1 620 kHz

LW: 144 kHz to 279 kHz

FM Tuner Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)

50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)

Alternate Channel Selectivity (400 kHz): 65 dB

Frequency Response: 40 Hz to 15 000 Hz

Stereo Separation: 30 dB

MW Tuner Sensitivity: 20 μV

Selectivity: 35 dB

LW Tuner Sensitivity: 50 μV

CD PLAYER SECTION

Type: Compact disc player

Signal Detection System: Non-contact optical pickup

(semiconductor laser)

Number of Channels: 2 channels (stereo)

Frequency Response: 5 Hz to 20 000 Hz

Dynamic Range: 93 dB

Signal-to-Noise Ratio: 98 dB

Wow and Flutter: Less than measurable limit

MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps

WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 192 kbps

ENGLISH

GENERAL

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance)

Grounding System: Negative ground

Allowable Operating Temperature: 0°C to +40°C

Dimensions (W × H × D): (approx.) Installation Size: 182 mm × 52 mm × 160 mm

Panel Size: 188 mm × 58 mm × 13 mm

Mass:

Design and specifications are subject to change without notice.

1.3 kg (excluding accessories)

21REFERENCES

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Vous avez des PROBLÈMES de fonctionnement?

Réinitialisez votre appareil

Référez-vous à la page intitulée Comment réinitialiser votre appareil

Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany

Cher(e) client(e), Cet appareil est conforme aux directives et normes européennes en vigueur concernant la compatibilité électromagnétique et à la sécurité électrique.

Représentant européen de la société Victor Company of Japan, Limited: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Allemagne

EN, FR

0908DTSMDTJEIN

KD-R303/KD-R302/KD-R301

Installation/Connection Manual Manuel d’installation/raccordement

0908DTSMDTJEIN

EN, FR

ENGLISH

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC IN-CAR ENTERTAINMENT dealers.

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC IN-CAR ENTERTAINMENT dealer.

• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 15 of the INSTRUCTIONS).

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

FRANÇAIS

Cet appareil est conçu pour fonctionner sur des sources de courant continu de 12 V à masse NEGATIVE. Si votre véhicule n’offre pas ce type d’alimentation, il vous faut un convertisseur de tension, que vous pouvez acheter chez un revendeur d’autoradios JVC.

Handles

Poignées

Washer (ø5)

Rondelle (ø5)

Lock nut (M5)

Ecrou d’arrêt (M5)

Mounting bolt (M4 × 5 mm; M5 × 12.5 mm)

Boulon de montage (M4 × 5 mm; M5 × 12,5 mm)

Rubber cushion

Amortisseur en caoutchouc

Control panel

Panneau de commande

Sleeve

Manchon

Trim plate

Plaque d’assemblage

Power cord

Cordon d’alimentation

Parts list for installation and connection

The following parts are provided for this unit. If any item is missing, consult your JVC IN-CAR ENTERTAINMENT dealer immediately.

Liste des pièces pour l’installation et raccordement

Les pièces suivantes sont fournies avec cet appareil. Si quelque chose manquait, consultez votre revendeur autoradio JVC immédiatement.

GET0568-010A

[EX/EU]

Heat sink

Dissipateur de chaleur

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit

will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

AVERTISSEMENTS

Pour éviter tout court-circuit, nous vous recommandons de débrancher la borne négative de la batterie et d’effectuer tous les raccordements électriques avant d’installer l’appareil.

• Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après l’installation.

Remarques:

• Remplacer le fusible par un de la valeur précisée. Si le fusible saute souvent, consulter votre revendeur d’autoradios JVC.

• Il est recommandé de connecter des enceintes avec une puissance de plus de 50 W (les enceintes arrière et les enceintes avant, avec une impédance comprise entre 4 Ω et 8 Ω). Si la puissance maximum est inférieure à 50 W, changez “AMP GAIN” pour éviter d’endommager vos enceintes (voir page 15 du MANUEL D’INSTRUCTIONS).

• Pour éviter les court-circuits, couvrir les bornes des fils qui ne sont PAS UTILISÉS avec de la bande isolante.

• Le dissipateur de chaleur devient très chaud après usage. Faire attention de ne pas le toucher en retirant cet appareil.

PRECAUTIONS sur l’alimentation et la connexion des enceintes:

• NE CONNECTEZ PAS les fils d’enceintes du cordon d’alimentation à la batterie; sinon, l’appareil serait sérieusement endommagé.

• AVANT de connecter les fils d’enceintes du cordon d’alimentation aux enceintes, vérifiez le câblage des enceintes de votre voiture.

Do the required electrical connections.

Réalisez les connexions électriques.

Lorsque vous mettez l’appareil à la verticale, faire attention de ne pas endommager le fusible situé sur l’arrière.

Non fourni avec cet autoradio.

Bend the appropriate tabs to hold the sleeve firmly in place.

Tordez les languettes appropriées pour maintenir le manchon en place.

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC IN-CAR ENTERTAINMENT dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Removing the unit

Before removing the unit, release the rear section.

INSTALLATION (MONTAGE DANS LE TABLEAU DE BORD)

L’illustration suivante est un exemple d’installation typique. Si vous avez des questions ou avez besoin d’information sur des kits d’installation, consulter votre revendeur d’autoradios JVC ou une compagnie d’approvisionnement.

• Si l’on n’est pas sûr de pouvoir installer correctement cet appareil, le faire installer par un technicien

qualifié.

Retrait de l’appareil

Avant de retirer l’appareil, libérer la section arrière.

Insert the two handles, then pull them as illustrated so that the unit can be removed.

Insérez les deux poignées, puis tirez de la façon illustrée de façon à retirer l’appareil.

When installing the unit without using the sleeve / Lors de l’installation de l’appareil scans utiliser de manchon

In a Toyota car for example, first remove the car radio and install the unit in its place.

Dans une voiture Toyota, par exemple, retirez d’abord l’autoradio et installez l’appareil à sa place.

When using the optional stay / Lors de l’utilisation du hauban en option

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws

are used, they could damage the unit.

Remarque : Lors de l’installation de l’appareil sur le support de montage, s’assurer d’utiliser des vis d’une longueur de

8 mm. Si des vis plus longues sont utilisées, elles peuvent endommager l’appareil.

Screw (option)

Vis (en option)

Stay (option)

Hauban (en option)

Fire wall

Cloison

Dashboard

Tableau de bord

Install the unit at an angle of less than 30˚.

Installez l’appareil avec un angle de moins de 30˚.

Bracket*

Support*

Flat type screws (M5 × 8 mm)*

Vis à tête plate (M5 × 8 mm)*

Pocket

Poche

Flat type screws (M5 × 8 mm)

Vis à tête plate (M5 × 8 mm)*

Bracket*

Support*

When you stand the unit, be careful not to damage the fuse on the rear.

Not supplied for this unit.

Before checking the operation of this unit prior to installation, this lead must be connected; otherwise, the

power cannot be turned on.

Non fourni avec cet autoradio.

Pour vérifier le fonctionnement de cet appareil avant installation, ce fil doit être raccordé, sinon l’appareil ne peut

pas être mis sous tension.

ENGLISH FRANÇAIS

ELECTRICAL CONNECTIONS RACCORDEMENTS ELECTRIQUES

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious

damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1 Cut the ISO connector. 2 Connect the colored leads of the power cord in the order specified in the illustration below. 3 Connect the aerial cord. 4 Finally connect the wiring harness to the unit.

Connections without using the ISO connector / Connexions sans utiliser le connecteur ISO

Avant de commencer la connexion: Vérifiez attentivement le câblage du véhicule. Une connexion

incorrecte peut endommager sérieusement l’appareil. Le fil du cordon d’alimentation et ceux des connecteurs du châssis de la voiture peuvent être différents en couleur.

1 Coupez le connecteur ISO. 2

Connectez les fils colorés du cordon d’alimentation dans l’ordre spécifié sur l’illustration ci-dessous.

3 Connectez le cordon d’antenne. 4 Finalement, connectez le faisceau de fils à l’appareil.

If your car is equipped with the ISO

connector / Si votre voiture est équippée d’un connecteur ISO

• Connect the ISO connectors as illustrated.

• Connectez les connecteurs ISO comme montré sur l’illustration.

From the car body

De la carrosserie de la voiture

ISO connector of the supplied power cord

Connecteur ISO pour le cordon d’alimentation fourni

View from the lead side

Vue à partir du côté des fils

For some VW/Audi or Opel (Vauxhall) automobiles / Pour certaines automobiles VW/Audi ou Opel (Vauxhall)

You may need to modify the wiring of the supplied power cord as illustrated.

• Contact your authorized car dealer before installing this unit.

Vous aurrez peut-être besoin de modifier le câblage du cordon d’alimentation fourni comme montré sur l’illustration.

• Contactez votre revendeur automobile autorisé avant d’installer l’appareil.

Original wiring / Câblage original

Modified wiring 1 / Câblage modifié 1

Use modified wiring 2 if the unit does not turn on.

Utilisez le câblage modifié 2 si l’appareil ne se met pas sous tension.

ISO connector

Connecteur ISO

Y: Yellow

Jaune

R: Red

Rouge

Modified wiring 2 / Câblage modifié 2

Rear line out (see diagram )

Sortie de ligne arrière (voir le diagramme )

Rear ground terminal

Borne arrière de masse

15 A fuse

Fusible 15 A

Aerial terminal

Borne de l’antenne

Black

Noir

Blue with white stripe

Bleu avec bande blanche

Red

Rouge

Yellow

Jaune *

To the metallic body or chassis of the car

Vers corps métallique ou châssis de la voiture

To an accessory terminal in the fuse block

Vers borne accessoire du porte-fusible

To the remote lead of other equipment or power aerial if any (200 mA max.)

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une (200 mA max.)

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

À une borne sous tension du porte-fusible connectée à la batterie de la voiture (en dérivant l’interrupteur d’allumage) (12 V constant)

Ignition switch

Interrupteur d’allumage

Fuse block

Porte-fusible

Left speaker (front)

Enceinte gauche (avant)

Right speaker (front)

Enceinte droit (avant)

Left speaker (rear)

Enceinte gauche (arrière)

Right speaker (rear)

Enceinte droit (arrière)

Purple

Violet

Purple with black stripe

Violet avec bande noire

Green

Vert

Green with black stripe

Vert avec bande noire

Gray

Gris

Gray with black stripe

Gris avec bande noire

White

Blanc

White with black stripe

Blanc avec bande noire

Brown

Marron

To cellular phone system

À un système de téléphone cellulaire

Connecting the external amplifier / Connexion d’un amplificateur extérieur

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint

(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

Cut the rear speaker leads of the car’s ISO connector and connect them to the amplifier.

Vous pouvez connecter un amplificateur pour améliorer votre système autoradio.

• Connectez le fil de commande à distance (bleu avec bande blanche) au fil de commande à distance de l’autre appareil de façon qu’il puisse être commandé via cet appareil.

• Déconnectez les enceintes de cet appareil et connectez-les à l’amplificateur. Laissez les fils d’enceintes de cet appareil inutilisés.

Rear speakers

Enceintes arrière

JVC Amplifier

JVC Amplificateur

Remote lead

Fil d’alimentation à distance

Y-connector (not supplied for this unit)

Connecteur Y (non fourni avec cet autoradio)

Remote lead (blue with white stripe)

Fil d’alimentation à distance (bleu avec bande blanche)

To the remote lead of other equipment or power aerial if any

Au fil de télécommande de l’autre appareil ou à l’antenne automatique s’il y en a une

Attachez solidement le fil de mise à la masse au châssis métallique de la voiture—à un endroit qui n’est pas

recouvert de peinture (s’il est recouvert de peinture, enlevez d’abord la peinture avant d’attacher le fil). L’appareil peut être endommagé si cela n’est pas fait correctement.

Coupez les fils des enceintes arrière du connecteur ISO de la voiture et connectez-les à l’amplificateur.

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds.

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all.

* Have you reset your unit?

EN CAS DE DIFFICULTES

• Le fusible saute.

* Les fils rouge et noir sont-ils racordés correctement?

• L’appareil ne peut pas être mise sous tension.

* Le fil jaune est-elle raccordée?

• Pas de son des enceintes.

* Le fil de sortie d’enceinte est-il court-circuité?

• Le son est déformé.

* Le fil de sortie d’enceinte est-il à la masse? * Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble à la masse?

• Interférence avec les sons.

* La prise arrière de mise à la terre est-elle connectée au châssis de la voiture avec un cordon court et épais?

• L’appareil devient chaud.

* Le fil de sortie d’enceinte est-il à la masse? * Les bornes “–” des enceintes gauche et droit sont-elles mises ensemble à la masse?

• Cet appareil ne fonctionne pas du tout.

* Avez-vous réinitialisé votre appareil?

Signal cord (not supplied for this unit)

Cordon de signal (non fourni avec cet autoradio)

Front speakers (see diagram

)

Enceintes avant (voir le diagramme )

Rear speakers

Enceintes arrière

CD RECEIVER

CD-RECEIVER

РЕСИВЕР С ПРОИГРЫВАТЕЛЕМ КОМПАКТ-ДИСКОВ

∆ΕΚΤΗΣ ΜΕ CD

KD-R303/KD-R302/KD-R301/ KD-R33

ENGLISHDEUTSCHРУCCKИЙ

ΕΛΛΗΝΙΚΑ

For canceling the display demonstration, see page 6. Zum Abbrechen der Displaydemonstration siehe Seite 6. Информацию об отмене демонстрации функций дисплея см. на стр. 6. Για να ακυρώσετε την επίδειξη λειτουργίας στην θóνη, βλ. σελίδα 6.

For installation and connections, refer to the separate manual. Für den Einbau und die Anschlüsse siehe das eigenständige Handbuch. Указания по установке и выполнению соединений приводятся в отдельной инструкции. Για πληρoφoρίες σχετικά µε την εγκατάσταση και τις συνδέσεις, ανατρέξτε στo αντίστoιχo ξεχωριστό εγχειρίδιo.

INSTRUCTIONS

BEDIENUNGSANLEITUNG

ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ

Ο∆ΗΓΙΕΣ

GET0568-006A

[EY]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

ENGLISH

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

Warning:

Battery

Products

Information for Users on Disposal of Old Equipment and Batteries [European Union only]

Notice:

The sign Pb below the symbol for batteries indicates that this battery contains lead.

If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

How to reset your unit

• Your preset adjustments will also be erased.

How to forcibly eject a disc

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

CONTENTS

OPERATIONS

Basic operations ........................................... 4

Preparation .................................................. 6

Listening to the radio ................................... 7

Disc operations ............................................. 10

EXTERNAL DEVICES

Listening to the other external

components .............................................. 11

SETTINGS

Selecting a preset sound mode .................... 12

Menu operations .......................................... 13

Color settings (for KD-R33) .......................... 16

ENGLISH

Detaching the control panel

Attaching the control panel

REFERENCES

More about this unit .................................... 17

Troubleshooting ........................................... 19

Maintenance ................................................ 21

Specifications ............................................... 22

Basic operations

ENGLISH

1 • FM/AM: Select preset station.

• CD: Select folder.

2 • Turn on the power.

• Attenuate the sound (if the power is on).

• Turn off the power [Hold].

3 Select the source.

FM = CD *1 = AUX IN *2 = AM *2 = (back to

the beginning)

4 • Enter list operations.

• Enter Menu setting [Hold] .

5 • Control the volume or selection [Turn]. *

• Confirm the selection [Press] . *

• FM: Enter SSM preset mode [Hold] . *

• CD: Enter playback mode [Hold] . *

6 Loading slot 7 Display window

8 Eject disc. 9 • Activate/deactivate TA Standby Reception.

• Enter PTY Searching mode [Hold].

p Detach the panel. q Change the display information. w • FM/AM: Search for station.

• CD: Select track.

e Return to the previous menu. r AUX (auxiliary) input jack

*1 You cannot select “CD” as the playback source if no

disc is in the unit.

*2 You cannot select these sources if they were disabled

in the Menu (see “Menu operations” on page 15).

*3 Also known as “Control dial” in this manual.

Display window

ENGLISH

1 Tr (track) indicator 2 Source display / Track number / Folder number /

Time countdown indicator

3 DISC indicator 4 Sound mode indicators—CLASSIC, HIP HOP, JAZZ,

ROCK, POPS, USER

5 Playback mode / item indicators— RND (random),

(disc), (folder), RPT (repeat)

6 EQ (equalizer) indicator

7 LOUD (loudness) indicator 8 Disc information indicators—

TAG (Tag information), (track/file), (folder)

9 Main display p Radio Data System indicators—AF, REG, TP, PTY q Tuner reception indicators—ST (stereo),

MO (monaural)

5OPERATIONS

Preparation

Cancel the display demonstration and set the clock

• See also page 13.

ENGLISH

Turn on the power.

Cancel the display demonstrations

Select “DEMO,” then “DEMO OFF.”

Set the clock

Select “CLOCK” = “CLOCK SET.” Adjust the hour, then press control dial once to proceed to adjust

[Turn] = [Press]

FM/AM Station Frequency

FM Radio Data System

CD Audio CD/CD Text: Disc title/performer *

Station name (PS) beginning)

MP3/WMA: Album name/performer (folder name) *2 = Track title (file name) *2 =

= Clock = (back to the beginning)

= Station Frequency = Programme type (PTY) = Clock = (back to the

elapsed playing time = Current track number with the clock time = (back to the beginning)

Current track number with the elapsed playing time = Current track number with the clock time = (back to the beginning)

the minute.

Select “24H/12H,” then “24 HOUR” or “12 HOUR.”

• To return to the previous menu, press BACK.

= Track title *1 = Current track number with the

If the current disc is an audio CD, “NO NAME” appears.

If an MP3/WMA file does not have Tag information or “TAG DISPLAY” is set to “TAG OFF” (see page 13),

folder name and file name appear.

Listening to the radio

1 2

Select “FM” or “AM.”

Search for a station to listen—Auto Search.

Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.

• When receiving an FM stereo broadcast with sufficient signal strength, “ST” lights up on the display.

When an FM stereo broadcast is

hard to receive

• See also page 14.

[Turn] = [Press]

ENGLISH

2 Select the preset number range you want to

store.

Select “TUNER” = “MONO”

= “MONO ON”

Reception improves, but stereo effect will be lost.

• “MO” lights up on the display.

To restore the stereo effect, repeat the same procedure to select “MONO OFF.” The MO indicator goes off.

FM station automatic presetting

— SSM (Strong-station Sequential Memory)

You can preset up to 18 stations for FM.

1 While listening to a station...

Local FM stations with the strongest signals are searched and stored automatically.

To preset other 6 stations, repeat from step 1 again.

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and 6 stations for AM. Ex.: Storing FM station of 92.50 MHz into preset

number “04.”

2 Select preset number “04.”

Continued on the next page

7OPERATIONS

3 Start searching for your favorite programme.

ENGLISH

Selecting preset station

[Turn] = [Press]

The following features are available only for FM Radio Data System stations.

Searching for FM Radio Data

System programme — PTY Search

You can tune in to a station broadcasting your favorite programme by searching for a PTY code.

1 The last selected PTY code

appears.

2 Select one of your favorite programme types

or a PTY code.

If a station is broadcasting a programme of the

same PTY code as you have selected, that station is tuned in.

Using the standby receptions

TA Standby Reception

To activate TA Standby Reception

The TP (Traffic Programme)

indicator either lights up or flashes.

• If the TP indicator lights up, TA Standby Reception is activated.

To activate the reception, tune in to another station

providing these signals. The TP indicator will stop flashing and remain lit.

To deactivate the TA Standby Reception

The TP indicator goes off.

PTY Standby Reception

PTY Standby Reception allows the unit to switch temporarily to your favorite PTY programme from any source other than AM.

To activate and select your favorite PTY code for PTY Standby Reception, see page 14.

The PTY indicator either lights up or flashes.

• If the PTY indicator lights up, PTY Standby Reception is activated.

• If the PTY indicator flashes, PTY Standby Reception is not yet activated.

To activate the reception, tune in to another station

providing these signals. The PTY indicator will stop flashing and remain lit.

Automatic station selection—

Programme Search

• The unit takes some time to tune in to another station using programme search.

• See also page 14.

PTY codes

ENGLISH

To deactivate the PTY Standby Reception, select “PTY OFF” for the PTY code (see page 14). The PTY indicator goes off.

Tracing the same programme—

Network-Tracking Reception

Programme A broadcasting on different frequency areas (01 – 05)

When shipped from the factory, Network-Tracking Reception is activated.

To change the Network-Tracking Reception setting, see “AF-REG” on page 14.

9OPERATIONS

Disc operations

ENGLISH

Stop playing and ejecting the disc

• “NO DISC” appears. Press SRC to listen to another playback source.

Prohibiting disc ejection

Turn on the power.

Insert a disc.

All tracks will be played repeatedly until you change the source or eject the disc.

Pressing (or holding) the following buttons allows you to...

MP3/WMA: Select folder

[Press] Select track [Hold] Reverse/fast-forward track

To cancel the prohibition, repeat the same procedure.

Selecting a track/folder

[Turn] = [Press]

• For MP3/WMA discs, select the desired folder, then the desired track by performing the control dial.

• To return to the previous menu, press BACK.

OPERATIONS

Selecting the playback modes

You can use only one of the following playback modes at a time.

[Turn] = [Press]

REPEAT Ô RANDOM

[Turn] = [Press]

REPEAT

TRACK RPT : Repeats current track FOLDER RPT : MP3/WMA: Repeats current folder

RANDOM

FOLDER RND : MP3/WMA: Randomly plays all

tracks of current folder, then tracks of next folders

ALL RND : Randomly plays all tracks

• To cancel repeat play or random play, select

“RPT OFF” or “RND OFF.”

• To return to the previous menu, press BACK.

ENGLISH

Listening to the other external components

You can connect an external component to AUX (auxiliary) input jack on the control panel. Preparation: Make sure “AUX ON” is selected in the “SRC SELECT” = “AUX IN” setting, see page 15.

1 2

—

Connecting an external component to the AUX input jack

—

Select “AUX IN.”

Turn on the connected component and start playing the source.

Adjust the volume.

You can adjust the auxiliary input level to avoid the sudden increase of the output level (see “AUX ADJUST” on page 15).

Adjust the sound as you want (see page 12).

3.5 mm stereo mini plug (not supplied)

OPERATIONS & EXTERNAL DEVICES

Portable audio player, etc.

Selecting a preset sound mode

You can select a preset sound mode suitable to the music genre.

• See also page 13 (“EQ”).

ENGLISH

[Turn] = [Press]

Select “EQ”

Preset value setting for each sound mode

Preset values

Indication (For)

BASS

TREBLE

LOUD

Storing your own sound mode

You can store your own adjustments in memory.

1 Select “USER” for “EQ.”

[Turn] = [Press]

Select “EQ”

= “USER”

2 While “USER” is shown on the display...

USER (Flat sound) 00 00 OFF ROCK (Rock or disco music) +03 +01 ON CLASSIC (Classical music) +01 –02 OFF POPS (Light music) +04 +01 OFF HIP HOP (Funk or rap music) +02 00 ON JAZZ (Jazz music) +02 +03 OFF

• If no operation is done for about 30 seconds, the operation will be canceled.

3 Select a tone.

[Turn] = [Press]

BASS Ô TREBLE

4 Adjust the level.

Tone Level BASS –06 to +06 TREBLE –06 to +06

• To return to the previous menu, press BACK.

5 Finish the procedure.

Menu operations

1 2 3 Repeat step 2 if necessary.

[Turn] = [Press]

Category Menu items Selectable settings, [reference page]

• To return to the previous menu, press BACK.

Initial: Underlined

ENGLISH

DEMO

Display

DEMO

demonstration

CLOCK DISP *

Clock display

CLOCK SET

Clock setting

CLOCK

24H/12H

Time display mode

CLOCK ADJ *

Clock adjustment

Equalizer

DIMMER

Dimmer

• DEMO ON

: Display demonstration will be activated automatically if no

operation is done for about 20 seconds, [6].

• DEMO OFF

• CLOCK ON

: Cancels. : Clock time is shown on the display at all times when the

power is turned off.

• CLOCK OFF

: Cancels; pressing DISP will show the clock time for about 5

seconds when the power is turned off, [6].

: Adjust the hour, then the minute, [6]. [Initial: 0:00]

• 24 HOUR

: See also page 6 for setting.

• 12 HOUR

• AUTO

: The built-in clock is automatically adjusted using the CT

(clock time) data in the Radio Data System signal.

• OFF

: Cancels.

: Select a preset sound mode suitable to the music genre. USER, ROCK, CLASSIC, POPS, HIP HOP, JAZZ

• DIMMER ON

• DIMMER OFF

: Dims the display and button illumination. : Cancels.

SCROLL*

Scroll

• SCROLL ONCE

• SCROLL AUTO

• SCROLL OFF

DISPLAY

Pressing DISP for more than one second can scroll the display regardless of the setting.

TAG DISPLAY

• TAG ON

Tag display

• TAG OFF

If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select

“CLOCK OFF” to save the car’s battery. *2 Takes effect only when CT (clock time) data is received. *3 Some characters or symbols will not be shown correctly (or will be blanked) on the display.

: Scrolls the displayed information once. : Repeats scrolling (at 5-second intervals). : Cancels.

: Shows the Tag information while playing MP3/WMA

tracks.

: Cancels.

Continued on the next page

SETTINGS

Category Menu items Selectable settings, [reference page]

ENGLISH

TUNER

AF-REG *

Alternative frequency/ regionalization reception

PTY-STANDBY *

PTY standby

TA VOLUME *

Traffic announcement volume

P-SEARCH *

Programme search

• AF ON

• AF-REG ON

• OFF

PTY OFF, PTY codes

VOLUME 00

– VOLUME 50 (or VOLUME 00 – VOLUME 30)*

• SEARCH ON

• SEARCH OFF

: When the currently received signals become weak, the unit

switches to another station (the programme may differ from the one currently received), [9].

• The AF indicator lights up. : When the currently received signals become weak, the

unit switches to another station broadcasting the same programme.

• The AF and REG indicators light up. : Cancels.

Activates PTY Standby Reception with one of the PTY codes, [9].

Initial: VOLUME 15

: Activates Programme Search, [9]. : Cancels.

MONO *

• MONO ON

Monaural mode

• MONO OFF

IF BAND

• AUTO

Intermediate frequency band

COLOR 01

• WIDE

: Select one of the preset or user color for display and button (except T/P/

– COLOR 29,

COLOR

USER

(See also page 16 for USER color settings.)

(for KD-R33)

MENU COLOR

Menu color

(for KD-R33)

MENU COLOR

Only for FM Radio Data System stations.

• OFF

• ON

*5 Depends on the amplifier gain control. *6 Displayed only when the source is “FM.”

: Activate monaural mode to improve FM reception, but

stereo effect will be lost, [7].

: Restore the stereo effect. : Increases the tuner selectivity to reduce interference noises

between adjacent stations. (Stereo effect may be lost.)

: Subject to interference noises from adjacent stations, but

sound quality will not be degraded and the stereo effect will remain.

/0) illumination.

: Cancels. : Changes the display and button (except T/P/ /0)

illumination during menu, list search and playback mode operations.

Category Menu items Selectable settings, [reference page]

FADER*

Fader BALANCE

Balance

LOUD

Loudness

AUX ADJUST

Auxiliary input level adjustment

AUDIO

BEEP

Keypress tone

TEL MUTING

Telephone muting

AMP GAIN *

Amplifier gain control

R06 – F06 : Adjust the front and rear speaker output balance.

[Initial: 00]

L06 – R06 : Adjust the left and right speaker output balance.

• LOUD OFF

• LOUD ON

[Initial: 00] : Cancels.

: Boost low and high frequencies to produce a well-balanced

ENGLISH

sound at a low volume level.

AUX ADJ 00 — AUX ADJ 05

: Adjust the auxiliary input level to avoid the sudden increase

of the output level when changing the source to external component connected to the AUX input jack on the control panel.

• BEEP OFF

• BEEP ON

• MUTING 1/

• MUTING OFF

• LOW POWER

MUTING 2

: Deactivates the keypress tone. : Activates the keypress tone.

: Select either one which mutes the sounds while using a

cellular phone.

: Cancels.

: VOLUME 00 – VOLUME 30 (Select if the maximum power

of each speaker is less than 50 W to prevent damaging the speaker.)

• HIGH POWER

: VOLUME 00 – VOLUME 50

AM *

AM station

AUX IN *

SRC SELECT

Auxiliary input

If you are using a two-speaker system, set the fader level to “00.”

• AM OFF

• AM ON

• AUX OFF

• AUX ON

: Disable “AM” in source selection. : Enable “AM” in source selection, [4].

: Disable “AUX IN” in source selection. : Enable “AUX IN” in source selection, [4].

*8 The volume level automatically changes to “VOLUME 30” if you change to “LOW POWER” with the volume level

set higher than “VOLUME 30.”

*9 Displayed only when any source other than “AM” is selected. *10 Displayed only when any source other than “AUX IN” is selected.

SETTINGS

Color settings (for KD-R33)

Creating your own color

—USER Color

ENGLISH

You can create your own colors—“DAY COLOR” or “NIGHT COLOR.” DAY COLOR: Used when “DIMMER” is set to

“DIMMER OFF.”

NIGHT COLOR: Used when “DIMMER” is set to

“DIMMER ON.”

Select “COLOR” = “USER.”

[Turn] = [Press]

3 While “USER” is shown on the display...

5 Select a primary color.

[Turn] = [Press]

6 Adjust the level (00 to 31) of the selected

primary color.

[Turn] = [Press]

If “00” is selected for all the primary colors, display

appears dim.

7 Repeat steps 5 and 6 to adjust other primary

colors.

[Turn] = [Press]

8 Exit from the setting.

• If no operation is done for about 30 seconds, the operation will be canceled.

SETTINGS

More about this unit

Basic operations

Turning on the power

• By pressing SRC button on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power.

General

• If you change the source while listening to a disc, playback stops.

Next time you select “CD” as the playback source,

playback will start from where it had been stopped previously.

• After ejecting a disc, “NO DISC” appears and you cannot operate some of the buttons. Insert another disc or press SRC to select another playback source.

• If no operation is done for about 30 seconds after pressing MENU button, the operation will be canceled.

FM Radio Data System operations

• Network-Tracking Reception requires two types of Radio Data System signals—PI (Programme Identification) and AF (Alternative Frequency) to work correctly. Without receiving these data correctly, Network-Tracking Reception will not operate correctly.

• If a Traffic Announcement is received by TA Standby Reception, the volume level automatically changes to the preset level (TA VOL) if the current level is lower than the preset level.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

ENGLISH

Tuner operations

Storing stations in memory

• During SSM search... – All previously stored stations are erased and the

stations are stored anew.

– When SSM is over, the station stored in the lowest

preset number will be automatically tuned in.

• When storing a station manually, the previously preset station is erased when a new station is stored in the same preset number.

General

• This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA), MP3/WMA formats.

• When a disc is inserted upside down, “PLEASE” and “EJECT” appear alternately on the display. Press 0 to eject the disc.

• MP3 and WMA “tracks” (words “file” and “track” are used interchangeably) are recorded in “folders.”

• While fast-forwarding or reversing on an MP3 or WMA disc, you can only hear intermittent sounds.

Continued on the next page

REFERENCES

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can only play back files of the same type as those detected first if a disc includes both audio CD (CD-DA) files and MP3/WMA files.

ENGLISH

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, or for the following reasons:

– Discs are dirty or scratched. – Moisture condensation has occurred on the lens

inside the unit. – The pickup lens inside the unit is dirty. – The files on the CD-R/CD-RW are written using the

“Packet Write” method. – There are improper recording conditions (missing

data, etc.) or media conditions (stained, scratched,

warped, etc.).

• CD-RWs may require a longer readout time since the

reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or a protective seal stuck

to the surface. – Discs on which labels can be directly printed by an

ink jet printer. Using these discs under high temperature or high

humidity may cause malfunctions or damage to the unit.

Playing an MP3/WMA disc

24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) – Disc format: ISO 9660 Level 1/Level 2, Romeo,

Joliet, Windows long file name

• The maximum number of characters for file/folder names vary depending on the disc format used (includes 4 extension characters—<.mp3> or <.wma>).

– ISO 9660 Level 1: up to 12 characters – ISO 9660 Level 2: up to 31 characters – Romeo: up to 128 characters – Joliet: up to 64 characters – Windows long file name: up to 128 characters

• This unit can recognize a total of 512 files, 255 folders, and 8 hierarchical levels.

• This unit can play back files recorded in VBR (variable bit rate).

Files recorded in VBR have a discrepancy in the

elapsed time display, and do not show the actual elapsed time. In particular, this difference becomes noticeable after performing the search function.

• This unit cannot play back the following files:

– MP3 files encoded in MP3i and MP3 PRO format. – MP3 files encoded in an inappropriate format. – MP3 files encoded with Layer 1/2. – WMA files encoded in lossless, professional, and

voice format.

– WMA files which are not based upon Windows

Media ® Audio. – WMA files copy-protected with DRM. – Files which have data such as AIFF, ATRAC3, etc.

• The search function works but search speed is not

constant.

• This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

• This unit can show the names of albums, artists (performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or

2.4) for MP3 files and for WMA files.

• This unit can display only one-byte characters. No other characters can be correctly displayed.

• This unit can play back MP3/WMA files meeting the conditions below:

– Bit rate: 8 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)

Ejecting a disc

• If the ejected disc is not removed within 15 seconds, it is automatically inserted into the loading slot again to protect it from dust. Playback starts automatically.

Menu operations

• If you change the “AMP GAIN” setting from “HIGH POWER” to “LOW POWER” while the volume level is set higher than “VOLUME 30,” the unit automatically changes the volume level to “VOLUME 30.”

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Check the cords and connections.

• The unit does not work at all. Reset the unit (see page 3).

General

• “AUX IN” cannot be selected. Check the “SRC SELECT”

page 15).

• Display appears dim. Check the USER Color settings (see page 16).

• SSM automatic presetting does not work. Store stations manually.

• Static noise while listening to the radio. Connect the aerial firmly.

FM/AM

• “AM” cannot be selected. Check the “SRC SELECT”

page 15).

= “AUX IN” setting (see

= “AM” setting (see

ENGLISH

• Disc cannot be played back. Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be skipped.

• Disc can neither be played back nor ejected. • Unlock the disc (see page 10).

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

Disc playback

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• “PLEASE” and “EJECT“ appear alternately on the display.

• Insert a finalized CD-R/CD-RW.

• Finalize the CD-R/CD-RW with the component which you used for recording.

• Eject the disc forcibly (see page 3).

• Change the disc.

• Check the cords and connections.

0, then insert a disc correctly.

Press

Continued on the next page

19REFERENCES

ENGLISH

Symptoms Remedies/Causes

• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file names.

• Noise is generated. Skip to another track or change the disc. (Do not add the extension code <.mp3> or <.wma> to non-MP3 or WMA tracks.)

• A longer readout time is required

(“READING” keeps flashing on the display).

MP3/WMA playback

• Tracks do not play back in the order you

have intended them to play.

• The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by

• The correct characters are not displayed

(e.g. album name).

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Do not use too many hierarchical levels and folders.

The playback order is determined when the files are recorded.

how the tracks are recorded on the disc.

This unit can only display letters (upper case), numbers, and a limited number of symbols.

Maintenance

How to clean the connectors

Connectors

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture has evaporated.

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs

Do not use the following discs:

Single CD (8 cm disc) Warped disc

ENGLISH

How to handle discs

When removing a disc from its case, press down the center holder

of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc in its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs in cases after use.

Center holder

Sticker and sticker residue Stick-on label

C-thru Disc (semi-

Unusual shape

Transparent or semi-

transparent parts on its

recording area

transparent disc)

21REFERENCES

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output: Front/Rear: 50 W per channel

ENGLISH

Continuous Power Output (RMS): Front/Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz

at no more than 0.8% total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)

Tone Control Range: Bass: ±12 dB at 100 Hz

Treble: ±12 dB at 10 kHz

Frequency Response: 40 Hz to 20 000 Hz

Signal-to-Noise Ratio: 70 dB

Line-Out Level/Impedance: 2.5 V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

Other Terminal: AUX (auxiliary) input jack

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 108.0 MHz

AM: MW: 522 kHz to 1 620 kHz

LW: 144 kHz to 279 kHz

FM Tuner Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)

50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)

Alternate Channel Selectivity (400 kHz): 65 dB

Frequency Response: 40 Hz to 15 000 Hz

Stereo Separation: 30 dB

MW Tuner Sensitivity: 20 μV

Selectivity: 35 dB

LW Tuner Sensitivity: 50 μV

CD PLAYER SECTION

Type: Compact disc player

Signal Detection System: Non-contact optical pickup

(semiconductor laser)

Number of Channels: 2 channels (stereo)

Frequency Response: 5 Hz to 20 000 Hz

Dynamic Range: 93 dB

Signal-to-Noise Ratio: 98 dB

Wow and Flutter: Less than measurable limit

MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps

WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 192 kbps

ENGLISH

GENERAL

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance)

Grounding System: Negative ground

Allowable Operating Temperature: 0°C to +40°C

Dimensions (W × H × D): (approx.) Installation Size: 182 mm × 52 mm × 160 mm

Panel Size: 188 mm × 58 mm × 13 mm

Mass:

Design and specifications are subject to change without notice.

1.3 kg (excluding accessories)

23REFERENCES

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Haben Sie PROBLEME mit dem Betrieb?

Bitte setzen Sie Ihr Gerät zurück

Siehe Seite Zurücksetzen des Geräts

Затруднения при эксплуатации?

Пожалуйста, перезагрузите Ваше устройство

Для получения информации о перезагрузке Вашего устройства обратитесь на

соответствующую страницу

Αντιµετωπίζετε ΠΡΟΒΛΗΜΑΤΑ λειτουργίας;

Εκτελέστε επαναφορά της µονάδας

Ανατρέξτε στην ενότητα “Επαναφορά της µονάδας”

Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Germany

Sehr geehrter Kunde, sehr geehrte Kundin, dieses Gerät stimmt mit den gültigen europäischen Richtlinien und Normen bezüglich elektromagnetischer Verträglichkeit und elektrischer Sicherheit überein.

Die europäische Vertretung für die Victor Company of Japan, Limited ist: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Deutschland

Уважаемый клиент. Данное устройство соответствует действительным Европейским директивам и стандартам по электромагнитной совместимости и электрической безопасности.

Представительство компании Victor Company of Japan, Limited в Европе: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Германия

Αγαπητέ πελάτη, η συσκευή αυτή συμμορφώνεται με τις ισχύουσες Ευρωπαϊκές Οδηγίες και πρότυπα σχετικά με την ηλεκτρομαγνητική συμβατότητα και την ασφάλεια από ηλεκτρισμό.

Ο Ευρωπαϊκός αντιπρόσωπος της Victor Company of Japan, Limited είναι: JVC Technical Services Europe GmbH Postfach 10 05 04 61145 Friedberg Γερμανία

EN, GE, RU, GR

0908DTSMDTJEIN

KD-R303/KD-R302/KD-R301/KD-R33

Installation/Connection Manual Einbau/Anschlußanleitung

Руководство по установке/подключению

Εγχειρίδιo εγκατάστασης/συνδέσεων

0908DTSMDTJEIN

EN, GE, RU, GR

ENGLISH

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your

vehicle does not have this system, a voltage inverter is required, which can be purchased at JVC INCAR ENTERTAINMENT dealers.

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC INCAR ENTERTAINMENT dealer.

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

GET0568-013A

[EY]

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the

power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the

power cord to the speakers, check the speaker wiring in your car.

Heat sink / Abstrahlblech

Радиатор / Ψύκτρα

Handles

Griffe

Рычаги

Κλειδιά

Washer (ø5)

Unterlegscheibe (ø5)

Шайба (њ5)

Ρoδέλα (ø5)

Lock nut (M5)

Sicherungsmutter (M5)

Фиксирующая гайка (M5)

Ασφαλιστικό παξιµάδι (M5)

Rubber cushion

Gummipuffer

Резиновый чехол

Ελαστικό παρέµβυσµα

A / B Hard case (only for KD-R33)/Control panel

Etui (nur für KD-R33)/Schalttafel

Жесткий футляр (только для KD-R33)/ Панель управления

Πρoστατευτική άκαµπτη θήκη (μόνο για το KD-R33)/Πρόσoψη

Sleeve

Halterung

Муфта

Βάση

Trim plate

Frontrahmen

Декоративную панель ∆ιακoσµητικό πλαίσιo

Power cord

Stromkable

Кабель питания

∆έσµη καλωδίων ρεύµατoς

Parts list for installation and connection

The following parts are provided for this unit. If any item is missing, consult your JVC IN-CAR ENTERTAINMENT dealer immediately.

DEUTSCH

Dieses Gerät ist für einen Betrieb in elektrischen Anlagen mit 12 V Gleichstrom und (–) Erdung ausgelegt. Verfügt Ihr Fahrzeug nicht über diese

Anlage, ist ein Spannungsinverter erforderlich, der bei JVC Autoradiohändler erworben werden kann.

WARNUNGEN

Zur Vermeidung von Kurzschlüssen empfehlen wir, daß Sie den negativen Batterieanschluß abtrennen und alle elektrischen Anschlüsse herstellen, bevor das Gerät eingebaut wird.

• Sicherstellen, daß das Gerät nach dem Einbau a Chassis des Fahrzeugs geerdet wird.

Hinweise:

• Die Sicherung mit einer der entsprechenden Nennleistung ersetzen. Brennt die Sicherung häufig durch, wenden Sie sich an ihren JVC Autoradiohändler.

• Es wird empfohlen, Lautsprecher mit einer Maximalleistung von mehr als 50 W anzuschließen (sowohl hinten als auch vorne, mit einer Impedanz von 4 Ω bis 8 Ω). Wenn die Maximalleistung weniger als 50 W beträgt, stellen Sie „AMP GAIN“ anders ein, um Schäden an den Lautsprechern zu vermeiden (siehe Seite 15 der BEDIENUNGSANLEITUNG).

• Zur Vermeidung eines Kurzschlusses die Anschlußklemmen der NICHT VERWENDETEN Leitungen mit Isolierklebeband umwickeln.

• Das Abstrahlblech wird nach dem Gebrauch sehr heiß. Beim Ausbau des Geräts darauf achten, das Abstrahlblech nicht zu berühren.

РУССКИЙ

Это устройство разработано для эксплуатации на 12 В постоянного напряжения с минусом на массе. Если Ваш автомобиль не имеет этой системы, требуется инвертор напряжения, который может быть приобретен у дилера автомобилнего специалиста JVC.

ПРЕДУПРЕЖДЕНИЯ

Для предотвращения коротких замыканий мы рекомендуем Вам отсоединить отрицательный разъем аккумулятора и осуществить все подключения перед установкой устройства.

• После установки обязательно заземлите данное устройство на шасси автомобиля.

Примечания:

• Заменяйте предохранитель другим предохранителем указанного класса. Если предохранитель сгорает слишком часто, обратитесь к дилеру автомобилнего специалиста JVC.

• Рекомендуется подключать динамики с максимальной мощностью более 50 Вт (к задней и передней панели устройства, с полным сопротивлением от 4 Ω до 8 Ω). Если максимальная мощность динамиков менее 50 Вт, перейдите в режим “AMP GAIN”, чтобы предотвратить их повреждение (см. ИНСТРУКЦИИ ПО ЭКСПЛУАТАЦИИ на стр. 15).

• Для предотвращения короткого замыкания заклейте НЕИСПОЛЬЗУЕМЫЕ концы изолирующей лентой.

• Радиатор во время использования сильно нагревается. Старайтесь его не трогать во время удаления устройства.

ΕΛΛΗΝΙΚΑ

Η συσκευή αυτή είναι σχεδιασµένη να λειτoυργεί σε ηλεκτρικά συστήµατα oχηµάτων στα 12 V DC, µε ΑΡΝΗΤΙΚΗ γείωση. Εάν τo όχηµά σας δεν ανήκει στην κατηγoρία αυτή, θα χρειαστείτε ένα µετατρoπέα τάσης, τoν oπoίo µπoρείτε να πρoµηθευτείτε από τoυς αντιπρoσώπoυς συστηµάτων ψυχαγωγίας oχηµάτων της JVC.

ΠΡΟΦΥΛΑΞΕΙΣ

Για την απoτρoπή τυχόν βραχυκυκλωµάτων, συνιστoύµε να απoσυνδέετε τoν αρνητικό πόλo της µπαταρίας και να κάνετε όλες τις ηλεκτρικές συνδέσεις πριν από την εγκατάσταση της συσκευής.

• Βεβαιωθείτε ότι θα γειώσετε τη συσκευή αυτή στo αµάξωµα τoυ oχήµατoς ξανά µετά την εγκατάσταση.

Σηµειώσεις:

• Εάν καεί η ασφάλεια, αντικαταστήστε την µε καινoύργια των ίδιων oνoµαστικών χαρακτηριστικών. Εάν η ασφάλεια καίγεται συχνά, συµβoυλευθείτε τoν αντιπρόσωπo συστηµάτων ψυχαγωγίας oχηµάτων της JVC.

• Συνιστάται να συνδέετε ηχεία µέγιστης ισχύoς πάνω από 50 W (τόσo πίσω όσo και µπρoστά, µε σύνθετη αντίσταση 4 Ω έως 8 Ω). Εάν η µέγιστη ισχύς των ηχείων είναι µικρότερη από 50 W, αλλάξτε τη ρύθµιση “AMP GAIN” (Απoλαβή ενισχυτή) για να απoτρέψετε ενδεχόµενη καταστρoφή τoυς (βλ. σελίδα 15 στις O∆ΗΓΙΕΣ).

• Για να απoτρέψετε τυχόν βραχυκυκλώµατα, καλύπτετε τoυς ακρoδέκτες των καλωδίων ΠOΥ ∆Ε XΡΗΣΙΜOΠOΙΕΙΤΕ µε µoνωτική ταινία.

• Η ψύκτρα ζεσταίνεται πoλύ κατά τη χρήση. Πρoσέχετε να µην την αγγίξετε καθώς αφαιρείτε τη συσκευή.

ПРЕДОСТЕРЕЖЕНИЯ по питанию и подключению громкоговорителей:

• НЕ подключайте провода громкоговорителей к аккумулятору автомобиля, иначе устройство будет повреждено.

• ПЕРЕД подключением проводов громкоговорителей к кабелю питания громкоговорителя проверьте схему соединений громкоговорителей в Вашем автомобиле.

VORSICHTSMASSREGELN beim Anschließen der Stromversorgung und Lautsprecher:

• Die Lautsprecherleitungen des Netzkabels NICHT an der Autobatterie anschließen, da sonst das Gerät schwer beschädigt wird.

• VOR dem Anschließen der Lautsprecherleitungen des Spannunsgversorgungskabels an die Lautsprecher, die Lautsprecherverdrahtung in Ihrem Auto überprüfen.

ΠΡOΦΥΛΑΞΕΙΣ κατά τις συνδέσεις τρoφoδoσίας ρεύµατoς και ηχείων:

• ΜΗ συνδέετε τα καλώδια ηχείων της συσκευής µε την µπαταρία τoυ oχήµατoς, διότι ενδέχεται να πρoκληθεί σoβαρή ζηµιά στη συσκευή.

• ΠΡOΤOΥ συνδέσετε τα καλώδια ηχείων της συσκευής µε τα ηχεία, ελέγξτε την καλωδίωση των ηχείων τoυ oχήµατoς.

Mounting bolt (M4 × 5 mm; M5 × 12,5 mm)

Befestigungsschraube (M4 × 5 mm; M5 × 12,5 mm)

Крепежный болт (M4 × 5 мм; M5 × 12,5 мм) Βίδα στερέωσης (M4 × 5mm; M5 × 12,5 mm)

Κατάλoγoς εξαρτηµάτων για την εγκατάσταση και τις συνδέσεις

Η συσκευή αυτή συνoδεύεται από τα εξαρτήµατα πoυ αναφέρoνται κατωτέρω. Αν λείπει κάποιο στοιχείο, συμβουλευτείτε αμέσως τον αντιπρόσωπο συστημάτων ψυχαγωγίας οχημάτων της JVC.

Teileliste für den Einbau und Anschluß

Die folgenden Teile werden zusammen mit diesem Gerät geliefert. Falls ein Artikel fehlt, wenden Sie sich sofort an Ihren JVC-Autoradiohändler.

Список деталей для установки и подключения

Следующие детали поставлены в комплекте с устройством. При отсутствии какого-либо элемента немедленно свяжитесь с дилером автомобильного специалиста JVC.

INSTALLATION (IN-DASH MOUNTING)

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

EINBAU (IM ARMATURENBRETT)

Die folgende Abbildung zeigt einen typischen Einbau. Bei irgendwelchen Fragen oder wenn Sie Informationen hinsichtlich des Einbausatzes brauchen, wenden Sie sich an ihren JVC Autoradiohändler oder ein Unternehmen das diese Einbausätze vertreibt.

• Sind Sie sich über den richtigen Einbau des Geräts nicht sicher, lassen Sie es von einem qualifizierten Techniker einbauen.

Do the required electrical connections.

Nehmen Sie die erforderlichen elektrischen Anschlüsse vor.

Выполните необходимые подключения контактов, как показано на оборотной стороне этой инструкции.

Κάντε τις αναγκαίες ηλεκτρικές συνδέσεις.

УСТАНОВКА (УСТАНОВКА В ПРИБОРНУЮ ПАНЕЛЬ)

На следующих иллюстрациях показана типовая установка. Если у Вас есть какие-либо вопросы, касающиеся установки, обратитесь к Вашему дилеру автомобилнего специалиста JVC или в компанию, поставляющую соответствующие принадлежности.

• Если Вы не знаете точно, как следует устанавливать это устройство, обратитесь к квалифицированному специалисту.

Bend the appropriate tabs to hold the sleeve firmly in place.

Die geeigneten Zapfen biegen, um die Manschette sicher festzuhalten.

Отогните соответствующие фиксаторы, предназначенные для прочной установки корпуса.

Λυγίστε τις κατάλληλες γλωττίδες για να συγκρατηθεί η βάση σταθερά στη θέση της.

ΕΓΚΑΤΑΣΤΑΣΗ (ΤOΠOΘΕΤΗΣΗ ΣΤO ΤΑΜΠΛΩ)

Η εικόνα πoυ ακoλoυθεί απεικoνίζει µια τυπική εγκατάσταση. Για oπoιαδήπoτε απoρία σας ή για περισσότερες πληρoφoρίες σχετικά µε κιτ εγκατάστασης, απευθυνθείτε στoν αντιπρόσωπo συστηµάτων ψυχαγωγίας oχηµάτων της JVC ή σε εταιρείες πoυ παρέχoυν τέτoια κιτ.

• Εάν έχετε αµφιβoλίες σχετικά µε τη σωστή εγκατάσταση της συσκευής αυτής, αναθέστε την εγκατάστασή της σε κατάλληλα εκπαιδευµένo τεχνικό.

Removing the unit

Before removing the unit, release the rear section.

Insert the two handles, then pull them as illustrated so that the unit can be removed.

Die beiden Handgriffe einsetzen und dann ziehen wie in der Abbildung gezeigt, so daß das Gerät entfernt werden kann.

Вставьте два рычажка, затем потяните их, как показано на рисунке, чтобы вынуть устройство.

Εισαγάγετε τις δύo λαβές και κατόπιν τραβήξτε τις, όπως φαίνεται στην εικόνα, µε τρόπo ώστε να είναι δυνατή η αφαίρεση της συσκευής.

When installing the unit without using the sleeve / Beim Einbau des Geräts ohne Halterung / При установке устройства без использования муфты / Όταν τoπoθετείτε τη συσκευή χωρίς χρήση της βάσης

In a Toyota car for example, first remove the car radio and install the unit in its place.

Zum Beispiel in einem Toyota zuerst das Autoradio ausbauen und dann das Gerät an seinem Platz einbauen.

В автомобиле Тойота, например, сначала извлеките автомобильный радиоприемник и установите устройство на место.

Στα oχήµατα της Toyota, για παράδειγµα, πρώτα πρέπει να αφαιρέσετε τo ραδιόφωνo και κατόπιν να τoπoθετήσετε τη συσκευή στη θέση τoυ.

When using the optional stay / Beim Verwenden der Anker-Option / При использовании дополнительной стойки / Όταν χρησιµoπoιείτε τo πρoαιρετικό στήριγµα

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer

screws are used, they could damage the unit.

Hinweis : Beim Anbringen des Gerät an der Konsole sicherstellen, daß 8 mm lange Schrauben verwendet werden.

Werden längere Schrauben verwendet, können sie das Gerät beschädigen.

Примечание : При установке устройства на крепежный кронштейн, используйте только винты длиной 8 мм.

При использовании более длинных винтов можно повредить устройство.

Σηµείωση : Όταν τoπoθετείτε τη συσκευή στo στήριγµα στερέωσης, βεβαιωθείτε ότι θα χρησιµoπoιήσετε τις βίδες

µήκoυς 8 mm. Εάν χρησιµoπoιήσετε µακρύτερες βίδες, ενδέχεται να πρoκαλέσετε ζηµιά στη συσκευή.

Screw (option)

Schraube (Option)

Винт (дополнительно)

Βίδα (πρoαιρετική)

Stay (option)

Anker (Option)

Стойка (дополнительно)

Γωνιακό στήριγµα (πρoαιρετικό)

Fire wall

Feuerwand

Стена

∆ιαχωριστικό τoίχωµα µηχανής

Dashboard

Armaturenbrett

Приборная панель

Ταµπλώ

Install the unit at an angle of less than 30˚.

Stellen Sie das Gerät mit einem Winkel von weniger als 30˚ auf.

Установите устройство под углом менее 30°.

Τoπoθετήστε τη µoνάδα υπό γωνία µικρότερη των 30°.

Bracket*2 / Konsole*2 /

Кронштейн

Γλωττίδα στερέωσης

Flat type screws (M5 × 8 mm)*

Senkkopfschrauben (M5 × 8 mm)*

Крепежные винты (M5 × 8 мм)*

Πλακέ βίδες (M5 × 8 mm)*

Pocket / Taschen /

Карман / Εσoχή

Flat type screws (M5 × 8 mm)

Senkkopfschrauben (M5 × 8 mm)*

Крепежные винты (M5 × 8 мм)*

Πλακέ βίδες (M5 × 8 mm)*

Bracket*2 / Konsole*

Кронштейн*2 / Γλωττίδα στερέωσης*

When you stand the unit, be careful not to damage

the fuse on the rear.

Not supplied for this unit.

Ausbau des Geräts

Vor dem Ausbau des Geräts den hinteren Teil freigeben.

Удаление устройства

Перед удалением устройства освободите заднюю часть.

Αφαίρεση της συσκευής

Πρoτoύ αφαιρέσετε τη συσκευή, απασφαλίστε τo πίσω µέρoς.

Beim Aufstellen des Geräts darauf achten, daß die

Sicherung auf der Rückseite nicht beschädigt wird.

Wird nicht mit Gerät mitgeliefert.

Устанавливайте устройство таким образом,

чтобы не повредить предохранитель, расположенный сзади.

Hе входит в комплект поставки.

Όταν τoπoθετείτε τη συσκευή σε όρθια θέση, πρoσέχετε να µην πρoκαλέσετε ζηµιά στην ασφάλεια πoυ βρίσκεται στo πίσω µέρoς της συσκευής.

∆ε συµπεριλαµβάνoνται στη συσκευασία της

συσκευής αυτής.

For KD-R33

Bei KD-R33

Для KD-R33

Για το KD-R33

ENGLISH DEUTSCH

Rear ground terminal / Hintere Erdungscanschlußklemme / Задний разъем заземления /

Ακρoδέκτης γείωσης στo πίσω µέρoς της συσκευής

15 A fuse

15 A Sicherung

Предохранитель 15 A

Ασφάλεια 15 A

Aerial terminal

Antennenanschlußklemme

Разъем антенны

Ακρoδέκτης κεραίας

Black

Schwarz

Черный

Μαύρo

Blue with white stripe

Blau mit weißem Streifen

Синий с белой полосой

Μπλε µε λευκή ρίγα

Red

Rot

Красный

Κóκκινo

Yellow

Gelb*

Желтый*

Κίτρινo*

Brown

Braun

Коричневый

Καφέ

To the metallic body or chassis of the car

Zur metallenen Karosserie oder zum Fahrwerk des Autos

К металлическому корпусу или шасси автомобиля

Πρoς µεταλλικó πλαίσιo ή αµάξωµα τoυ oχήµατoς

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

Zur einer stromführenden Anschlußklemme im Sicherungsblock zum Anschließen an die Autobatterie (Umgehen des Zündschalters) (konstant 12 V)

К разъему фазы в блоке предохранителя (минуя блок зажигания) (постоянный 12 В)

Πρoς ακρoδέκτη της ασφαλειoθήκης πoυ τρoφoδoτείται απ’ ευθείας απó την µπαταρία τoυ oχήµατoς (παρακάµπτoντας τo διακóπτη της µηχανής) (συνεχής τρoφoδoσία 12 V)

Ignition switch

Zündschalter

Переключатель зажигания

∆ιακóπτης της µηχανής

Fuse block

Sicherungsblock

Блок предохранителя

Ασφαλειoθήκη

To an accessory terminal in the fuse block

Zur einer Zubehöranschlußklemme im Sicherungsblock

К вспомогательному разъему в блоке предохранителя

Πρoς ακρoδέκτη της ασφαλειoθήκης πoυ τρoφoδoτείται απó τo διακóπτη της µηχανής

To the remote lead of other equipment or power aerial if any (200 mA max.)

Zum Zusatzkabel des anderen Geräts oder der Motorantenne, sofern vorhanden (max. 200 mA)

К удаленному проводу другого оборудования или антенны (макс. 200 мА)

Πρoς καλώδιo τηλεχειρισµoύ άλλης συσκευής ή ηλεκτρική κεραία, εάν υπάρχει (200 mA τo πoλύ)

Left speaker (front)

Linker Lautsprecher (vorne)

Левый громкоговоритель (передний)

Αριστερó ηχείo (µπρoστά)

Right speaker (front)

Rechter Lautsprecher (vorne)

Правый громкоговоритель (передний)

∆εξί ηχείo (µπρoστά)

Left speaker (rear)

Linker Lautsprecher (hinten)

Левый громкоговоритель (задний)

Αριστερó ηχείo (πίσω)

Right speaker (rear)

Rechter Lautsprecher (hinten)

Правый громкоговоритель (задний)

∆εξί ηχείo (πίσω)

Purple

Lila

Пурпурный

Μωβ

Purple with black stripe

Lila mit schwarzem Streifen

Пурпурный с черной полосой

Μωβ µε µαύρη ρίγα

Green

Grün

Зеленый Πράσινo

Green with black stripe

Grün mit schwarzem Streifen

Зеленый с черной полосой

Πράσινo µε µαύρη ρίγα

Gray

Grau

Серый

Γκρι

Gray with black stripe

Grau mit schwarzem Streifen

Серый с черной полосой

Γκρι µε µαύρη ρίγα

White

Weiß

Белый

Λευκó

White with black stripe

Weiß mit schwarzem Streifen

Белый с черной полосой

Λευκó µε µαύρη ρίγα

РУССКИЙ

If your car is equipped with the ISO

connector / Wenn Ihr Fahrzeug mit dem ISO-Steckverbinder ausgestattet ist / Если автомобиль оснащен разъемом ISO / Εάν τо óχηµά σας διαθέτει σύνδεσµо ISO

• Connect the ISO connectors as illustrated.

• Schließen Sie die ISO-Steckverbinder an, wie in der Abbildung gezeigt.

• Подключите разъемы ISO, как показано на рисунке.

• Συνδέστε τоυς συνδέσµоυς ISO σύµφωνα µε την εικóνα.

From the car body

Von der Fahrzeugkarosserie

От корпуса автомобиля

Απó τо αµάξωµα τоυ оχήµατоς

ISO connector of the supplied power cord

ISO-Stecker des mitgelieferten Stromkabels

Разъем ISO шнура питания, входящего в комплект поставки

Σύνδεσµоς ISO της δέσµης καλωδίων της συσκευής

View from the lead side

Von der Kabelseite aus gesehen

Вид со стороны выводов

Όψη απó την πλευρά των καλωδίων

For some VW/Audi or Opel (Vauxhall) automobiles / Bei bestimmten VW-/Audi- oder Opel(Vauxhall-) Fahrzeugen / Для некоторых автомобилей VW/Audi или Opel (Vauxhall) / Για ορισμένα αυτοκίνητα VW

You may need to modify the wiring of the supplied power cord as illustrated.

• Contact your authorized car dealer before installing this unit.

Es kann erforderlich sein, die Verdrahtung des mitgelieferten Stromkabels zu modifizieren, wie in der Abbildung gezeigt.

• Wenden Sie sich vor dem Einbau dieses Receivers an Ihre Auto-Fachwerkstatt.

Возможно, потребуется изменить схему соединений для прилагаемого шнура питания, как показано на рисунке.

• Перед установкой приемника обратитесь к авторизованному агенту по продажам автомобильных систем.

Ενδέχεται να χρειαστεί να τρоπоπоιήσετε την καλωδίωση της παρεχóµενης δέσµης καλωδίων ρεύµατоς, σύµφωνα µε την εικóνα.

• Πρоτоύ εγκαταστήσετε τη συσκευή αυτή, απευθυνθείτε στоν εξоυσιоδоτηµένо αντιπρóσωπо τоυ оχήµατóς σας.

Original wiring / Original verdrahtung / Исходная схема соединений / Αρχική καλωδίωση

Modified wiring 1 / Modifizierte Verdrahtung 1 / Преобразованная схема соединений 1 / Τρоπоπоιηµένη καλωδίωση 1

Use modified wiring 2 if the unit does not turn on. / Verwenden Sie die modifizierte

Verdrahtung 2 wenn der Receiver nicht einschaltet. / Если приемник не включается, используйте преобразованную схему соединений 2. / Εάν η συσκευή δεν τίθεται σε λειτоυργία, χρησιµоπоιήστε την τρоπоπоιηµένη καλωδίωση 2.

ISO connector

ISO-Steckverbinder

Разъем ISO

Σύνδεσµоς ISO

Y: Yellow

Gelb

Желтый

Κίτρινо

R: Red

Rot

Красный

Κóκκινо

Modified wiring 2 / Modifizierte Verdrahtung 2 / Преобразованная схема соединений 2 / Τρоπоπоιηµένη καλωδίωση 2

Connections without using the ISO connector / Anschlüsse ohne Verwendung des ISO-Steckverbinders / Подключение без использования

разъема ISO / Συνδέσεις χωρίς τη χρήση των συνδέσμων ISO

Vor dem Anschließen: Die Verdrahtung im Fahrzeug

sorgfältig überprüfen. Falsche Anschlüsse können ernsthafte Schäden am Gerät hervorrufen. Die Leiter des Stromkabels und die Leiter des Anschlusses im Fahrzeug können sich farblich unterscheiden.

Schneiden Sie den ISO-Steckverbinder auf.

Die farbigen Adern des Stromkabels in der Reihenfolge

anschließen, wie in der Abbildung unten gezeigt.

Das Antennenkabel anschließen.

Die Kabelbäume am Gerät anschließen.

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

Cut the ISO connector.

Connect the colored leads of the power cord in the

order specified in the illustration below.

Connect the aerial cord.

Finally connect the wiring harness to the unit.

Перед началом подключений: Тщательно проверьте проводку в автомобиле. Неправильное подключение может привести к серьезному повреждению устройства. Жилы силового кабеля и жилы соединителя от кузова автомобиля могут быть разного цвета.

Обрежьте разъем ISO.

Подсоедините цветные провода шнура питания

в указанном ниже порядке.

Подключите кабель антенны.

В последнюю очередь подключите

электропроводку к устройству.

ELECTRICAL CONNECTIONS ELEKTRISCHE ANSCHLÜSSE

ЭЛЕКТРИЧЕСКИЕ ПОДКЛЮЧЕНИЯ

Not supplied for this unit.

Before checking the operation of this unit prior to

installation, this lead must be connected, otherwise the power cannot be turned on.

Wird nicht mit Gerät mitgeliefert.

*2 Vor der Überprüfung der Funktionsfähigkeit

des Geräts vor dem Einbau, muß diese Leitung angeschlossen werden, da sonst die Stromversorgung nicht eingeschaltet werden kann.

Не входит в комплект поставки.

*2 Перед проверкой работы устройства

подключите этот провод, иначе питание не включится.

To cellular phone system

Zur Mobiltelefon

К системе сотового телефона

Πρoς σύστηµα κινητoύ τηλεφώνoυ

ΕΛΛΗΝΙΚΑ

ΗΛΕΚΤΡΙΚΕΣ ΣΥΝ∆ΕΣΕΙΣ

Πριν απó τη σύνδεση: Ελέγξτε πρоσεκτικά την καλωδίωση τоυ оχήµατоς. Η τυχóν εσφαλµένη σύνδεση είναι δυνατó να πρоκαλέσει σоβαρή ζηµιά στη συσκευή. Τα καλώδια της δέσµης καλωδίων ρεύµατоς της συσκευής ενδέχεται να µην έχоυν τо ίδιо χρώµα µε τα καλώδια τоυ συνδέσµоυ τоυ оχήµατоς.

Κóψτε τоν συνδετήρα ISO.

Συνδέστε τα χρωµατιστά καλώδια της δέσµης

καλωδίων ρεύµατо

, µε τη σειρά πоυ καθоρίζεται

στην εικóνα ανωτέρω.

Συνδέστε τо оµоαξоνικó καλώδιо της κεραίας.

Τέλоς, συνδέστε τо βύσµα της δέσµης καλωδίων

ρεύµατо

στη συσκευή.

Rear line out (see diagram )

Hinterer Line-Ausgang (

siehe Schaltplan

)

Разъем “line out” заднего динамика

(см. схему )

Πίσω έξοδος line out (βλ. σχεδιάγραµµα

)

∆ε συµπεριλαµβάνoνται στη συσκευασία της συσκευής

αυτής.

Πρoτoύ ελέγξετε τη λειτoυργία της συσκευής, πριν απó

την εγκατάστασή της, θα πρέπει να συνδέσετε τo καλώδιo αυτó, διαφoρετικά η συσκευή δε θα τεθεί σε λειτoυργία.

Connecting the external amplifier / Anschließen des externen Verstärkers / Подключение внешнего усилителя / Σύνδεση του εξωτερικού

ενισχυτοή

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit,

connect them to the amplifier. Leave the speaker leads of this unit unused.

Можно подключить усилитель для обновления автомобильной стереосистемы.

• Подсоедините провод внешнего устройства (синий с белой полосой) к проводу внешнего устройства другого оборудования так, чтобы им можно было управлять с этого устройства.

• Отсоедините громкоговорители от данного устройства, подключите их к усилителю. Оставьте провода громкоговорителей данного устройства неиспользованными.

Rear speakers

Hintere Lautsprecher

Задние

громкоговорители

Πίσω ηχεία

JVC Amplifier

JVC Verstärker

JVC-усилитель

Ενισχυτής JVC

Remote lead

Fernbedienungsleitung

Провод внешнего устройства

Καλώδιo τηλεχειρισµoύ

Remote lead (blue with white stripe)

Fernbedienungsleitung (blau mit weißem Streifen)

Провод внешнего устройства (cиний с белой полосой)

Καλώδιo τηλεχειρισµoύ (µπλε µε λευκή ρίγα)

To the remote lead of other equipment or power aerial if any

Zum Zusatzkabel des anderen Geräts oder der Motorantenne, sofern vorhanden

К удаленному проводу другого оборудования или антенны

Πρoς καλώδιo τηλεχειρισµoύ άλλης συσκευής ή ηλεκτρική κεραία, εάν υπάρχει

Sie können einen Verstärker anschließen, um Ihre Autostereoanlage zu erweitern.

• Schließen Sie das Fernbedienungskabel (blau mit weißem Streifen) an das Fernbedienungskabel des anderen Geräts an, so daß es über dieses Gerät gesteuert werden kann.

• Die Lautsprecher von diesem Gerät abtrennen und am Verstärker anschließen. Die Lautsprecherleitungen dieses Geräts unbenutzt lassen.

Y-connector (not supplied for this unit)

Y-Anschluß (wird nicht mit Gerät mitgeliefert)

Разъем Y (не входит в комплект поставки)

∆ιακλαδωτήρας (δε συμπεριλαμβάνoνται στη συσκευασία τησ συσκευήσ αυτήσ)

Firmly attach the ground wire to the metallic body

or to the chassis of the car—to the place not coated with paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

Cut the rear speaker leads of the car’s ISO

connector and connect them to the amplifier.

*3 Verbinden Sie den Erdungsleiter mit der Karosserie

oder dem Rahmen des Fahrzeugs. Die Kontaktstelle darf nicht lackiert sein (sollte die Kontaktstelle lackiert sein, entfernen Sie den Lack der Kontaktstelle, bevor Sie den Leiter befestigen). Wenn der Erdungsleiter nicht ordnungsgemäß angeschlossen wird, kann dieses Gerät beschädigt werden.

*4 Schneiden Sie die hinteren Lautsprecherkabel des

ISO-Steckverbinders des Fahrzeugs ab, und schließen diese an den Verstärker an.

*3 Плотно прикрепите заземляющий провод

к металлическому кузову или шасси автомобиля—в месте, не покрытом краской (если оно покрыто краской, удалите краску перед тем, как прикреплять провод). Невыполнение этого требования может привести к повреждению данного устройства.

*4 Отрежьте провода задних громкоговорителей

разъема ISO и подсоеди ните их к усилителю.

Signal cord (not supplied for this unit)

Einzelleitung (wird nicht mit Gerät mitgeliefert)

Кабель сигнала (не входит в комплект поставки)

Καλώδιo σήµατoς (δε συμπεριλαμβάνoνται στη

Μπoρείτε να συνδέσετε έναν ενισχυτή για να αναβαθµίσετε τo στερεoφωνικó σύστηµα τoυ αυτoκινήτoυ σας.

• Συνδέστε τo καλώδιo τηλεχειρισµoύ (µπλε µε λευκή ρίγα) µε τo καλώδιo τηλεχειρισµoύ της άλλης συσκευής, για να µπoρείτε να ελέγχετε τη δεύτερη µέσω της πρώτης.

• Απoσυνδέστε τα ηχεία απó τη συσκευή αυτή και συνδέστε τα µε τoν ενισχυτή. Αφήστε τα καλώδια ηχείων της συσκευής αυτής ασύνδετα.

Rear speakers / Hintere Lautsprecher /

Задние громкоговорители / Πίσω ηχεία

Front speakers (see diagram

)

Vordere Lautsprecher (siehe Schaltplan

)

Передние громкоговорители (см. схему ) Εµπρóς ηχεία (βλ. σχεδιάγραµµα )

Στερεώστε γερά τo καλώδιo γείωσης στo µεταλλικó

πλαίσιo ή τo αµάξωµα τoυ oχήµατoςσε σηµείo πoυ δεν είναι βαµµένo (σε αντίθετη περίπτωση, ξύστε τη βαφή πρoτoύ συνδέσετε τo καλώδιo). Αν δεν τo κάνετε αυτó, είναι δυνατó να πρoκληθεί ζηµιά στη συσκευή.

Κóψτε τα καλώδια των πίσω ηχείων απó τo

σύνδεσµo ISO τoυ oχήµατoς και συνδέστε τα στoν ενισχυτή.

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers

grounded in common?

• Noise interfere with sounds.

* Is the rear ground terminal connected to the car’s

chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers

grounded in common?

• This unit does not work at all.

* Have you reset your unit?

FEHLERSUCHE

• Die Sicherung brennt durch.

* Sind die roten und schwarzen Leitungen richtig

angeschlossen?

• Stromversorgung kann nicht eingeschaltet werden.

* Ist die gelbe Leitung angeschlossen?

• Kein Ton aus den Lautsprechern.

Ist die Lautsprecherausgangsleitung kurzgeschlossen?

• Ton verzerrt.

* Ist die Lautsprecherausgangsleitung geerdet? * Sind die „–“ Anschlußklemmen der linken und

rechten Lautsprecher zusammen geerdet?

• Störgeräusche im Klang.

* Ist die hintere Erdungsklemme mit kürzeren

und dickeren Kabeln an das Fahrzeugchassis angeschlossen?

• Gerät wird heiß.

* Ist die Lautsprecherausgangsleitung geerdet? * Sind die „–“ Anschlußklemmen der linken und

rechten Lautsprecher zusammen geerdet?

• Dieser Receiver funktioniert überhaupt nicht.

* Haben Sie einen Reset am Receiver vorgenommen?

BЫЯВЛЕНИЕ НЕИСПРАВНОСТЕЙ

• Сработал предохранитель.

* Правильно ли подключены черный и

красный провода?

• Питание не включается.

* Подключен ли желтый провод?

• Звук не выводится через громкоговорители.

* Нет ли короткого замыкания на кабеле

выхода громкоговорителей?

• Звук искажен.

* Заземлен ли провод выхода

громкоговорителей?

* Заземлены ли разъемы “–” правого (R) и

левого (L) громкоговорителей?

• Шум мешает звучанию.

* Соединен ли находящийся сзади зажим

заземления с шасси автомобиля с помощью более короткого и тонкого шнуров?

• Устройство нагревается.

* Заземлен ли провод выхода

громкоговорителей?

* Заземлены ли разъемы “–” правого (R) и

левого (L) громкоговорителей?

• Приемник не работает.

* Выполнена ли перенастройка приемника?

ΑΝΤΙΜΕΤΩΠΙΣΗ ΠΡOΒΛΗΜΑΤΩΝ

• Η ασφάλεια καίγεται.

* Είναι τo κόκκινo και τo µαύρo καλώδιo σωστά

συνδεδεµένα;

• Η συσκευή δεν τίθεται σε λειτoυργία.

* Είναι τo κίτρινo καλώδιo συνδεδεµένo;

• ∆εν παράγεται ήχoς στα ηχεία.

* Μήπως τo καλώδιo εξόδoυ πρoς τα ηχεία είναι

βραχυκυκλωµένo;

• O ήχoς παράγεται µε παραµόρφωση.

* Μήπως τo καλώδιo εξόδoυ πρoς τα ηχεία είναι

γειωµένo;

* Μήπως oι ακρoδέκτες “–” των αριστερών (L) και

των δεξιών (R) ηχείων είναι γειωµένoι σε κoινό σηµείo;

•

O θόρυβoς πρoκαλεί παρεµβoλές στoυς παραγόµενoυς ήχoυς.

* Είναι o πίσω ακρoδέκτης γείωσης συνδεδεµένoς

µε τo αµάξωµα τoυ αυτoκινήτoυ µε κoντύτερo και παχύτερo καλώδιo;

• Η συσκευή ζεσταίνεται πoλύ.

* Μήπως τo καλώδιo εξόδoυ πρoς τα ηχεία είναι

γειωµένo;

* Μήπως oι ακρoδέκτες “–” των αριστερών (L) και

των δεξιών (R) ηχείων είναι γειωµένoι σε κoινό σηµείo;

• O δέκτης αυτός δεν λειτoυργεί καθόλoυ.

* Έχετε επαναφέρει τo δέκτη;

1– EN

ENGLISH

KD-R304/KD-R204

CD RECEIVER: INSTRUCTIONS/INSTALLATION

0808DTSMDTJEIN

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit.

Installation/connection are explained at the last section of this manual (reverse page, indicated with

symbol).

GET0566-001A

[UI]

Warning

If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident.

Caution on volume setting

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

For safety...

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

How to reset your unit

Reset the unit after installation is complete.

• Your preset adjustments will also be erased.

How to forcibly eject a disc

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

PREPARATIONS

Enter Menu operation. Select an item.

Basic settings

1 Cancel the display demonstrations

Select “DEMO,” then “DEMO OFF.”

2 Set the clock

Select “CLOCK” = “CLOCK SET.” Adjust the hour, then press control dial once

to proceed to adjust the minute.

• To return to the previous menu, press BACK.

IMPORTANT FOR LASER PRODUCTS

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified

service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

[European Union only]

Playing an MP3/WMA disc (for KD-R304)

• This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

• This unit can show the names of albums, artists (performer), and tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for MP3 files and for WMA files

• This unit can display only one-byte characters. No other characters can be correctly displayed.

• This unit can play back MP3/WMA files meeting the conditions below:

– Bit rate: 8 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) – Disc format: ISO 9660 Level 1/ Level 2, Romeo, Joliet,

Windows long file name

• The maximum number of characters for file/folder names vary depending on the disc format used (includes 4 extension characters—<.mp3> or <.wma>).

– ISO 9660 Level 1: up to 12 characters; ISO 9660 Level

2: up to 31 characters; Romeo: up to 128 characters; Joliet: up to 64 characters; Windows long file name: up to 128 characters

• This unit can recognize a total of 512 files, 255 folders, and 8 hierarchical levels.

• This unit can play back files recorded in VBR (variable bit rate).

Files recorded in VBR have a discrepancy in the elapsed

time display, and do not show the actual elapsed time. In particular, this difference becomes noticeable after performing the search function.

• This unit cannot play back the following files:

– MP3 files: encoded in MP3i and MP3 PRO format; an

inappropriate format; layer 1/2.

– WMA files: encoded in lossless, professional, and voice

format; not based upon Windows Media® Audio; copyprotected with DRM.

– Files which have data such as AIFF, ATRAC3, etc.

• The search function works but search speed is not constant.

Title assignment

• If you try to assign titles to more than 30 station frequencies, “NAME FULL” appears. Delete unwanted titles before assignment.

Basic operations

• By pressing SRC on the unit, you can also turn on the power. If the source is ready, playback also starts.

• If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power.

• If no operation is done for about 30 seconds after pressing MENU button, the operation will be canceled.

Tuner operations

• During SSM search...

– All previously stored stations are erased and the

stations are stored anew.

– When SSM is over, the station stored in the lowest

preset number will be automatically tuned in.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

General

• This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA) and MP3/WMA (for KD-R304) formats.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not be played back on this unit:

– Discs are dirty or scratched. – Moisture condensation has occurred on the lens inside

the unit. – The pickup lens inside the unit is dirty. – The files on the CD-R/CD-RW are written using the

“Packet Write” method. – There are improper recording conditions (missing data,

etc.) or media conditions (stained, scratched, warped,

etc.).

• CD-RWs may require a longer readout time since the

reflectance of CD-RWs is lower than that of regular CDs.

MORE ABOUT THIS UNIT

To keep discs clean

Wipe in a straight line from center of disc to edge. Do not use liquid cleaners, thinners, or benzene.

To play new discs

Remove any rough areas from the inner and outer edges of the disc.

MAINTENANCE

How to clean the connectors

Wipe the connectors with a cotton swab or cloth moistened with alcohol.

Moisture condensation

Moisture may condense on the lens inside the unit. Eject the disc and leave the unit turned on for a few hours until the moisture has evaporated.

Connectors

Do not use the following discs:

Warped disc Sticker and sticker residue Stick-on label

Unusual shape

Single CD (8 cm disc)

C-thru Disc (semi-transparent disc)

Transparent or semi-transparent parts on its recording area

Detaching the control panel

Attaching the control panel

2 – EN

INSTRUCTIONS

Basic operations

Select the source.

• Turn on the power.

• Attenuate the sound (if the power is on).

• Turn off the power [Hold].

• Control the volume or selection [Turn].

• Confirm the selection [Press] .

• FM: Enter SSM preset mode [Hold] .

• CD: Enter playback mode [Hold] .

Detach the panel.

Check the current clock time/other information. See also “CLOCK DISP“ of “Menu operations.”

Control panel

Display window

Disc indicator

Playback mode / item indicator

• ST: Lights up when receiving an FM stereo broadcast with sufficient signal strength.

• MO: Lights up in monaural mode.

• Source display

• Track number

• Folder number (for KD-R304)

• Time countdown indicator

Main display (time, playback information)

EQ (equalizer) indicator

Sound mode indicator

LOUD (loudness) indicator

Disc information indicators (for KD-R304)

Tr (track) indicator

*1 You cannot select these sources if they were disabled in the Menu (See “Menu operations”). *

You cannot select “CD” as the playback source if no disc is in the unit.

OPERATIONS

When an FM stereo broadcast is hard to receive

Reception improves, but the stereo effect will be lost. (MO indicator lights up.)

To restore the stereo effect, repeat the same procedure to select “MONO OFF.” The MO indicator goes off.

FM station automatic presetting —SSM (Strong-station Sequential Memory)

You can preset up to 18 stations for FM.

To preset other 6 stations, repeat from step 1 again.

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and 6 stations for AM. Example: Storing the FM station of 92.50 MHz into preset number “04”.

Selecting preset station

Radio operations

Select “FM” or “AM.”

Search for a station—Auto Search.

Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.

Select “TUNER” = “MONO” = “MONO ON” (See also “Menu operations.”)

Select preset number “04.”

Disc operations

Turn on the power.

Insert disc.

All tracks will be played repeatedly until you change the source or eject the disc.

Eject disc.

• “NO DISC” appears. Press SRC to listen to another playback source.

•

4 / ¢

[Press] Go to the previous or next track. [Hold] Reverse or fast-forward the track.

•

5 / ∞ : KD-R304: Go to the previous or next folder (for MP3/WMA discs).

Selecting the playback modes

Changing the display information

While playing an audio CD or CD Text

While playing an MP3 or a WMA disc (for KD-R304)

= B = Disc title/

performer *1 = Track title *1 = (back to the beginning)

A = B = Album name/ performer (folder name *2)

= Track title (file name *

)

= (back to the beginning)

A : The elapsed playing time with the current track

number

B : Clock with the current track number

If the current disc is an audio CD, “NO NAME” appears.

*2 If an MP3/WMA file does not have tags or “TAG

DISPLAY” is set to “TAG OFF,” folder name and

file name appear.

REPEAT

TRACK RPT : Repeats current track FOLDER RPT

(for KD-R304)

: MP3/WMA: Repeats current

folder

RANDOM

FOLDER RND (for KD-R304)

: MP3/WMA: Randomly plays

all tracks of current folder, then tracks of next folders

ALL RND : Randomly plays all tracks

• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”

• To return to the previous menu, press BACK.

Prohibiting disc ejection

To cancel the prohibition, repeat the same procedure.

Selecting a track/folder

• KD-R304: For MP3/WMA disc, select the desired folder, then the desired track by performing the control dial.

• To return to the previous menu, press BACK.

REPEAT

∆

RANDOM

• Adjusts the volume level.

3.5 mm stereo mini plug (not supplied)

Portable audio player, etc.

Turn on the connected component and start playing the source.

External component operations

You can connect an external component to the AUX (auxiliary) input jack on the control panel.

• Make sure “AUX ON” is selected in the “SRC SELECT”

= “AUX IN” setting, see “Menu operations.”

Remote controller—RM-RK50

RM-RK50 is supplied only for KD-R304

• Turns the power on if pressed briefly or attenuates the sound when power is on.

• Turns the power off if pressed and held.

• Changes the preset stations.

• KD-R304: Changes the folders of MP3/ WMA discs.

• Selects the sound mode (iEQ: intelligent equalizer).

• Selects the source.

• Searches for stations if pressed briefly.

• Fast-forwards or reverses the track if pressed and held.

• Changes the track of the disc if pressed briefly.

7 Installing battery

Warning: To prevent accidents and damage

• Do not install any battery other than CR2025 or its equivalent.

• Store out of reach of children.

• Do not recharge, short, or dismantle.

• Do not dispose of in fire.

• Do not carry around with other metallic materials.

Lithium coin battery (CR2025)

7 Features

Caution:

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

If the effectiveness of the remote controller decreases, replace the battery.

Remote sensor (for KD-R304)

DO NOT expose to strong light.

Return to the previous menu.

Refer to table on right

3 – EN

INSTRUCTIONS

Audio amplifier section

Maximum Power Output: Front/Rear: 50 W per channel Continuous Power Output (RMS): Front/Rear: 19 W per channel into 4 Ω, 40 Hz

to 20 000 Hz at no more than 0.8%

total harmonic distortion. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Tone Control Range: Bass: ±12 dB at 100 Hz Treble: ±12 dB at 10 kHz Frequency Response: 40 Hz to 20 000 Hz Signal-to-Noise Ratio: 70 dB Line-Out Level/Impedance:

2.5 V/20 kΩ load (full scale) Output Impedance: 1 kΩ Other Terminal: AUX (auxiliary) input jack

Tuner section

Frequency Range: FM: 87.5 MHz to 108.0 MHz AM: 531 kHz to 1 602 kHz

[FM Tuner]

Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω) 50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω) Alternate Channel Selectivity (400 kHz): 65 dB Frequency Response: 40 Hz to 15 000 Hz Stereo Separation: 30 dB

[AM Tuner]

Sensitivity/Selectivity: 20 μV/35 dB

SPECIFICATIONS

CD player section

Type: Compact disc player Signal Detection System: Non-contact optical pickup

(semiconductor laser) Number of channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 93 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit

[For KD-R304]

MP3 Decoding Format: MPEG1/2 Audio Layer 3 Max. Bit Rate: 320 kbps WMA (Windows Media® Audio) Decoding Format:

Max. Bit Rate: 192 kbps

General

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance) Grounding System: Negative ground Allowable Operating Temperature: 0°C to +40°C Dimensions (W × H × D): Installation Size (approx.): 182 mm × 52 mm × 160 mm Panel Size (approx.): 188 mm × 58 mm × 6 mm Mass (approx.):

1.3 kg (excluding accessories)

Design and specifications are subject to change without notice.

TROUBLESHOOTING

Symptoms Remedies/Causes

General

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Check the cords and connections.

• This unit does not work at all. Reset the unit.

• “AUX IN” cannot be selected. Check the “SRC SELECT”

= “AUX IN” setting (see “Menu

operations”).

FM/AM

• SSM automatic presetting does not work. Store stations manually.

• Static noise while listening to the radio. Connect the antenna firmly.

• “AM” cannot be selected. Check the “SRC SELECT”

= “AM” setting (see “Menu

operations”).

Disc playback

• Disc cannot be played back. Insert the disc correctly.

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be skipped.

• Insert a finalized CD-R/CD-RW.

• Finalize the CD-R/CD-RW with the component which you used for recording.

• Disc can be neither played back nor ejected.

• Unlock the disc.

• Eject the disc forcibly.

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

• Change the disc.

• Check the cords and connections.

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• “PLEASE” and “EJECT” appear alternately on the display.

Press 0, then insert a disc correctly.

MP3/WMA playback (for KD-R304)

• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant

with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file names.

• Noise is generated. Skip to another track or change the disc. (Do not add the extension

code <.mp3> or <.wma> to non-MP3 or WMA tracks.)

• A longer readout time is required (“READING” keeps flashing on the display).

Do not use too many hierarchical levels and folders.

• Tracks are not played back in the order you have intended.

Playback order is determined when the files are recorded.

• The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by how the

tracks are recorded on the disc.

• The correct characters are not displayed (e.g. album name).

This unit can only display letters (upper case), numbers, and a limited number of symbols.

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Sound adjustments

* You can change “USER” settings and store as your own sound mode (see below).

Storing your own sound mode

Title assignment

You can assign titles to 30 station frequencies (FM and AM) using 8 characters (maximum) for each title.

To erase the entire title

In step 2 above...

Menu operations

Menu items Selectable settings

DEMO

DEMO • DEMO ON: The display demonstration will be activated automatically if no operation is done for

about 20 seconds.

• DEMO OFF: Cancels.

CLOCK

CLOCK DISP *1• CLOCK ON: The clock time is shown on the display at all times when the power is turned off.

• CLOCK OFF: Cancels; pressing DISP will show the clock time for about 5 seconds when the power is turned off.

CLOCK SET : Adjust the hour, then the minute. [Initial: 1:00]

EQ : Select a preset sound mode suitable to the music genre.

USER, ROCK, CLASSIC, POPS, HIP HOP, JAZZ

DISPLAY

DIMMER • DIMMER ON: Dims the display and button illumination.

• DIMMER OFF: Cancels.

SCROLL*

• SCROLL ONCE: Scrolls the displayed information once.

• SCROLL AUTO: Repeats scrolling (at 5-second intervals).

• SCROLL OFF: Cancels.

Pressing DISP for more than one second can scroll the display regardless of the setting.

TAG DISPLAY (for KD-R304)

• TAG ON: Shows the Tag information while playing MP3/WMA tracks.

• TAG OFF: Cancels.

TUNER

MONO *3• MONO ON: Activate monaural mode to improve FM reception, but stereo effect will be lost.

• MONO OFF: Restore the stereo effect.

IF BAND • AUTO: Increases the tuner selectivity to reduce interference noises between adjacent stations.

(Stereo effect may be lost.)

• WIDE: Subject to interference noises from adjacent stations, but sound quality will not be degraded and the stereo effect will remain.

AUDIO

FADER*4R06 – F06: Adjust the front and rear speaker output balance. [Initial: 00]

BALANCE L06 – R06: Adjust the left and right speaker output balance. [Initial: 00]

LOUD • LOUD OFF: Cancels.

• LOUD ON: Boost low and high frequencies to produce a well-balanced sound at a low volume level.

AUX ADJUST AUX ADJ 00 – AUX ADJ 05: Adjust the auxiliary input level to avoid the sudden increase of the

output level when changing the source to external component connected to the AUX input jack on the control panel.

If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select “CLOCK

OFF” to save the car’s battery.

Some characters or symbols will not be shown correctly (or will be blanked) on the display.

*3 Displayed only when the source is “FM.” *4 If you are using a two-speaker system, set the fader level to “00.”

Preset values

SETTINGS

Select “EQ”

Indication (For)

BASS

TREBLE

LOUD

USER (Flat sound) 00 00 OFF

ROCK (Rock or disco music) +03 +01 ON

CLASSIC (Classical music) +01 –02 OFF

POPS (Light music) +04 +01 OFF

HIP HOP (Funk or rap music) +02 00 ON

JAZZ (Jazz music) +02 +03 OFF

Select “USER” for “EQ.”

This mode will be canceled if no operation is done for about 30 seconds.

1 Select a tone.

BASS Ô TREBLE

2 Adjust the Lever.

–06 to +06

3 Repeat 1 and 2 for the

other tone if necessary.

Select “FM” or “AM.”

Show the title entry screen.

Select a character.

Move to the next (or previous) character position.

Repeat steps 1 and 2 until you finish entering the title.

Finish the procedure.

Menu items Selectable settings

AUDIO

BEEP • BEEP ON: Activates the keypress tone.

• BEEP OFF: Deactivates the keypress tone.

AMP GAIN *

• HIGH POWER: VOLUME 00 – VOLUME 50

• LOW POWER: VOLUME 00 – VOLUME 30 (Select if the maximum power of each speaker is less than 50 W to prevent damaging the speaker.)

SRC SELECT

AM *

• AM OFF: Disable “AM” in source selection.

• AM ON: Enable “AM” in source selection.

AUX IN *

• AUX OFF: Disable “AUX IN” in source selection.

• AUX ON: Enable “AUX IN” in source selection.

The volume level automatically changes to “VOLUME 30” if you change to “LOW POWER” with the volume level is set

higher than “VOLUME 30.”

*6 Displayed only when any source other than “AM” is selected. *7 Displayed only when any source other than “AUX IN” is selected.

Initial: Underlined

While “USER” is shown on the display...

Repeat step 2 if necessary.

• To return to the previous menu, press BACK.

4 – EN

INSTALLATION / CONNECTION

In dash-mounting

Do the required electrical connections.

Bend the appropriate tabs to hold the sleeve firmly in place.

When you stand the unit, be careful not to damage the fuse on the rear.

Removing the unit

Before removing the unit, release the rear section.

When using the optional stay

Install the unit at an angle of less than 30˚.

Screw (option)

Stay (option)

Fire wall

Dashboard

When installing the unit without using the sleeve

Flat type screws —M5 × 8 mm *

Pocket

Flat type screws—M5 × 8 mm *

Bracket*

* Not supplied for this unit.

In a Toyota car for example, first remove the car radio and install the unit in its place.

TROUBLESHOOTING

• The fuse blows. * Are the red and black leads connected correctly?

• Power cannot be turned on. * Is the yellow lead connected?

• No sound from the speakers. * Is the speaker output lead short-circuited?

• Sound is distorted. * Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds. * Is the rear ground terminal connected to the car’s chassis using shorter and

thicker cords?

• This unit becomes hot. * Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all. * Have you reset your unit?

Å Control panel .......................................................................................... 1

ı Hard case (for KD-R304) ..........................................................................1

Ç Sleeve ..................................................................................................... 1

Î Trim plate ...............................................................................................1

ELECTRICAL CONNECTIONS

Purple

Front speaker (left)

To the automatic antenna if any (250 mA max.)

Blue

Red

To an accessory terminal in the fuse block

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

Yellow

To the metallic body or chassis of the car

Black

Ignition switch

15 A fuse

Fuse block

Rear speaker (left)

Rear speaker (right)

Front speaker (right)

White with black stripe

Rear ground terminal

Antenna terminal

Gray with black stripe

Green

Gray

Green with black stripe

Purple with black stripe

White

Typical connections

Use the front speaker lead if your speaker system is two-speaker system.

Rear line out

1 Connect the colored leads of the power cord in the order specified in the illustration below. 2 Connect the antenna cord. 3 Finally connect the wiring harness to the unit.

*1 Not supplied for this unit. *2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the power cannot

be turned on.

*3 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if

coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

Rear speakers

Remote lead

Remote lead (blue with white stripe)

To the remote lead of other equipment or automatic antenna if any

Y-connector

JVC Amplifier

Connecting the external amplifier

Front speakers

Signal cord

PRECAUTIONS on power supply and speaker connections

PREPARATION

This unit is designed to operate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required,

which can be purchased at JVC car audio dealers.

INSTALLATION

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Parts list for installation and connection

È Rubber cushion ....................................................................................... 1

Ô Handles ................................................................................................... 2

 Remote controller (for KD-R304) .............................................................1

Ò Battery (for KD-R304) ..............................................................................1

‰ Power cord ..............................................................................................1

Ï Washer (ø5) ............................................................................................ 1

Ì Lock nut (M5) ..........................................................................................1

Ó Mounting bolt—M4 x 5 mm; M5 x 12.5 mm ..........................................1

To the remote lead of other equipment (200 mA max.)

Blue with white stripe

For KD-R304

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

Heat sink

CD RECEIVER KD-R306/KD-R305/KD-R206/KD-R205

KD-R306/KD-R305/KD-R206/KD-R205

ENGLISH

For canceling the display demonstration, see page 7.

For installation and connections, refer to the separate manual.

INSTRUCTIONS

GET0564-001A

[U/UH]

Thank you for purchasing a JVC product.

Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best

possible performance from the unit.

IMPORTANT FOR LASER PRODUCTS

ENGLISH

1. CLASS 1 LASER PRODUCT

2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to

qualified service personnel.

3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical

instruments.

4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.

For safety...

[European Union only]

Warning:

If you need to operate the unit while driving, be sure to look around carefully or you may be involved in a traffic accident.

Caution on volume setting:

Discs produce very little noise compared with other sources. Lower the volume before playing a disc to avoid damaging the speakers by the sudden increase of the output level.

• Do not raise the volume level too much, as this will block outside sounds, making driving dangerous.

• Stop the car before performing any complicated operations.

Temperature inside the car...

If you have parked the car for a long time in hot or cold weather, wait until the temperature in the car becomes normal before operating the unit.

How to reset your unit

CONTENTS

OPERATIONS

Basic operations ........................................... 4

• Using the control panel ............................... 4

• Using the remote controller (RM-RK50) ...... 6

Preparation .................................................. 7

ENGLISH

• Your preset adjustments will also be erased.

How to forcibly eject a disc

• Be careful not to drop the disc when it ejects.

• If this does not work, reset your unit.

Detaching the control panel

Listening to the radio ................................... 8

Disc operations ............................................. 9

EXTERNAL DEVICES

Listening to the other external

components .............................................. 10

SETTINGS

Selecting a preset sound mode .................... 11

Title assignment .......................................... 12

Menu operations .......................................... 13

REFERENCES

More about this unit .................................... 15

Troubleshooting ........................................... 17

Maintenance ................................................ 19

Specifications ............................................... 20

Attaching the control panel

Basic operations

Using the control panel

ENGLISH

1 • FM/AM: Select preset station.

• CD: Select folder (for KD-R306/KD-R305).

2 • Turn on the power.

• Attenuate the sound (if the power is on).

• Turn off the power [Hold].

3 Select the source.

FM = AM *1 = CD *2 = AUX IN *1 = (back to

the beginning)

4 • Enter list operations.

• Enter Menu setting [Hold] .

5 • Control the volume or selection [Turn]. *

• Confirm the selection [Press] . *

• FM: Enter SSM preset mode [Hold] . *

• CD: Enter playback mode [Hold] . *

6 Loading slot 7 Display window

8 Eject disc. 9 Select the sound. p Detach the panel. q Change the display information. w • FM/AM: Search for station.

• CD: Select track.

e Return to the previous menu. r Remote sensor (for KD-R306/KD-R305) t AUX (auxiliary) input jack

*1 You cannot select these sources if they were disabled

in the Menu (see “Menu operations” on page 14).

*2 You cannot select “CD” as the playback source if no

disc is in the unit.

*3 Also known as “Control dial” in this manual.

Display window

ENGLISH

1 Tr (track) indicator 2 Source display / Track number / Folder number /

Time countdown indicator

3 DISC indicator 4 Sound mode indicators—CLASSIC, HIP HOP, JAZZ,

ROCK, POPS, USER

5 EQ (equalizer) indicator 6 LOUD (loudness) indicator

7 Disc information indicators (for KD-R306/

KD-R305)—TAG (Tag information), (track/ file), (folder)

8 Main display 9 Playback mode / item indicators—RND (random),

(disc), (folder), RPT (repeat)

p Tuner reception indicators—ST (stereo),

MO (monaural)

5OPERATIONS

Using the remote controller (RM-RK50)

RM-RK50 is supplied only for KD-R306/KD-R305

Installing the lithium coin battery (CR2025)

ENGLISH

Caution:

• Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

• Battery shall not be exposed to excessive heat such as sunshine, fire, or the like.

If the effectiveness of the remote controller decreases, replace the battery.

Before using the remote controller:

• Aim the remote controller directly at the remote sensor on the unit.

• DO NOT expose the remote sensor to bright light (direct sunlight or artificial lighting).

Remote sensor

1 • Turns the power on if pressed briefly or

attenuates the sound when the power is on.

• Turns the power off if pressed and held.

2 • Changes the preset stations.

• Changes the folder of the MP3/WMA.

3 Adjusts the volume level. 4 Selects the sound mode. 5 Selects the source. 6 • Searches for stations if pressed briefly.

• Fast-forwards or reverses the track if pressed and held.

• Changes the tracks if pressed briefly.

Warning (to prevent accidents and damage):

• Do not install any battery other than CR2025 or its

equivalent.

• Do not leave the remote controller in a place (such

as dashboards) exposed to direct sunlight for a long time.

• Store the battery in a place where children cannot

reach.

• Do not recharge, short, disassemble, heat the battery,

or dispose of it in a fire.

• Do not leave the battery with other metallic

materials.

• Do not poke the battery with tweezers or similar

tools.

• Wrap the battery with tape and insulate when

throwing away or saving it.

Preparation

Cancel the display demonstration and set the clock

• See also page 13.

Turn on the power.

ENGLISH

Cancel the display demonstrations

Select “DEMO,” then “DEMO OFF.”

Set the clock

Select “CLOCK” = “CLOCK SET.” Adjust the hour, then press control dial once to proceed to adjust

[Turn] = [Press]

FM/AM Station name *

CD Audio CD/CD Text: Disc title/performer *

MP3/WMA *4: Album name/performer (folder name) *3 = Track title (file name) *3 =

= Frequency = Clock = (back to the beginning)

elapsed playing time = Current track number with the clock time = (back to the beginning)

Current track number with the elapsed playing time = Current track number with the clock time = (back to the beginning)

the minute.

• To return to the previous menu, press BACK.

= Track title *2 = Current track number with the

If no title is assigned to a station, “NO NAME” appears. To assign a title to a station, see page 12.

* *2 If the current disc is an audio CD, “NO NAME” appears. *3 KD-R306/KD-R305: If an MP3/WMA file does not have Tag information or “TAG DISPLAY” is set to “TAG

OFF” (see page 13), folder name and file name appear.

*4 For KD-R306/KD-R305.

7OPERATIONS

Listening to the radio

1 2

ENGLISH

Select “FM” or “AM.”

Search for a station to listen—Auto Search.

Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.

• When receiving an FM stereo broadcast with sufficient signal strength, “ST”

When an FM stereo broadcast is

hard to receive

• See also page 14.

[Turn] = [Press]

lights up on the display.

2 Select the preset number range you want to

store.

Select “TUNER” = “MONO”

= “MONO ON”

Reception improves, but stereo effect will be lost.

• “MO” lights up on the display.

To restore the stereo effect, repeat the same procedure to select “MONO OFF.” The MO indicator goes off.

FM station automatic presetting

— SSM (Strong-station Sequential Memory)

You can preset up to 18 stations for FM.

1 While listening to a station...

Local FM stations with the strongest signals are searched and stored automatically.

To preset other 6 stations, repeat from step 1 again.

Manual presetting (FM/AM)

You can preset up to 18 stations for FM and 6 stations for AM. Ex.: Storing FM station of 92.50 MHz into preset

number “P04.”

2 Select preset number “P04.”

Selecting preset station

Disc operations

[Turn] = [Press]

ENGLISH

Turn on the power.

Insert a disc.

All tracks will be played repeatedly until you change the source or eject the disc.

Stop playing and ejecting the disc

• “NO DISC” appears. Press SRC to listen to another playback source.

Prohibiting disc ejection

To cancel the prohibition, repeat the same

procedure.

Selecting a track/folder

[Turn] = [Press]

• KD-R306/KD-R305: For MP3/WMA discs, select the desired folder, then the desired track by performing the control dial.

• To return to the previous menu, press BACK.

Pressing (or holding) the following buttons allows you to...

KD-R306/KD-R305 MP3/WMA: Select folder

[Press] Select track [Hold] Reverse/fast-forward track

Continued on the next page

9OPERATIONS

Selecting the playback modes

You can use only one of the following playback modes at a time.

ENGLISH

[Turn] = [Press]

REPEAT Ô RANDOM

[Turn] = [Press]

REPEAT

TRACK RPT : Repeats current track FOLDER RPT * : MP3/WMA: Repeats current folder

RANDOM

FOLDER RND * : MP3/WMA: Randomly plays all

tracks of current folder, then tracks of next folders

ALL RND : Randomly plays all tracks

• To cancel repeat play or random play, select

“RPT OFF” or “RND OFF.”

• To return to the previous menu, press BACK.

* For KD-R306/KD-R305.

Listening to the other external components

You can connect an external component to AUX (auxiliary) input jack on the control panel. Preparation: Make sure “AUX ON” is selected in the “SRC SELECT” = “AUX IN” setting, see page 14.

1 2

—

Connecting an external component to the AUX input jack

—

Select “AUX IN.”

Turn on the connected component and start playing the source.

Adjust the volume.

You can adjust the auxiliary input level to avoid the sudden increase of the output level (see “AUX ADJUST” on page 14).

Adjust the sound as you want (see page 11).

OPERATIONS & EXTERNAL DEVICES

Portable audio player, etc.

3.5 mm stereo mini plug (not supplied)

Selecting a preset sound mode

You can select a preset sound mode suitable to the music genre.

• See also page 13 (“EQ”).

Selecting from Menu.

[Turn] = [Press]

Select “EQ”

Storing your own sound mode

You can store your own adjustments in memory.

1 Select “USER” for “EQ.”

[Turn] = [Press]

Select “EQ” = “USER”

2 While “USER” is shown on the display...

ENGLISH

Preset value setting for each sound mode

Preset values

Indication (For) USER (Flat sound) 00 00 OFF ROCK (Rock or disco music)

CLASSIC (Classical music) +01 –02 OFF POPS (Light music) +04 +01 OFF HIP HOP (Funk or rap music) +02 00 ON JAZZ (Jazz music) +02 +03 OFF

BASS

+03 +01 ON

TREBLE

LOUD

• If no operation is done for about 30 seconds, the operation will be canceled.

3 Select a tone.

[Turn] = [Press]

BASS Ô TREBLE

4 Adjust the level.

Tone Level BASS –06 to +06 TREBLE –06 to +06

To return to the previous menu, press BACK.

5 Finish the procedure.

SETTINGS

Title assignment

You can assign titles to 30 station frequencies (FM and AM) using 8 characters (maximum) for each title.

1 Select “FM” or “AM.”

ENGLISH

2 Show the title entry screen.

3 Assign a title.

1 Select a character.

2 Move to the next (or previous) character

position.

3 Repeat steps 1 and 2 until you finish

entering the title.

4 Finish the procedure.

To erase the entire title

In step 2 above...

Menu operations

1 2 3 Repeat step 2 if necessary.

[Turn] = [Press]

Category Menu items Selectable settings, [reference page]

• To return to the previous menu, press BACK.

Initial: Underlined

ENGLISH

DEMO

Display

DEMO

demonstration

CLOCK DISP *

Clock display

CLOCK

CLOCK SET

Clock setting

Equalizer

DIMMER

Dimmer

SCROLL*

Scroll

DISPLAY

• DEMO ON

: Display demonstration will be activated automatically if no

operation is done for about 20 seconds, [7].

• DEMO OFF

• CLOCK ON

: Cancels. : Clock time is shown on the display at all times when the

power is turned off.

• CLOCK OFF

: Cancels; pressing DISP will show the clock time for about 5

seconds when the power is turned off, [7].

: Adjust the hour, then the minute, [7]. [Initial: 1:00]

: Select a preset sound mode suitable to the music genre. USER, ROCK, CLASSIC, POPS, HIP HOP, JAZZ

• DIMMER ON

• DIMMER OFF

• SCROLL ONCE

• SCROLL AUTO

• SCROLL OFF

: Dims the display and button illumination. : Cancels.

: Scrolls the displayed information once. : Repeats scrolling (at 5-second intervals).

: Cancels. Pressing DISP for more than one second can scroll the display regardless of the setting.

TAG DISPLAY

Tag display

• TAG ON

• TAG OFF

(For KD-R306/ KD-R305)

If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select

“CLOCK OFF” to save the car’s battery.

Some characters or symbols will not be shown correctly (or will be blanked) on the display.

: Shows the Tag information while playing MP3/WMA tracks.

: Cancels.

Continued on the next page

SETTINGS

Category Menu items Selectable settings, [reference page]

ENGLISH

TUNER

AUDIO

MONO *

Monaural mode

IF BAND

Intermediate frequency band

FADER*

Fader BALANCE

Balance

LOUD

Loudness

AUX ADJUST

Auxiliary input level adjustment

• MONO ON

: Activate monaural mode to improve FM reception, but stereo

effect will be lost, [8].

• MONO OFF

• AUTO

: Restore the stereo effect. : Increases the tuner selectivity to reduce interference noises

between adjacent stations. (Stereo effect may be lost.)

• WIDE

: Subject to interference noises from adjacent stations, but

sound quality will not be degraded and the stereo effect will remain.

R06 – F06 : Adjust the front and rear speaker output balance.

[Initial: 00]

L06 – R06 : Adjust the left and right speaker output balance.

[Initial: 00]

• LOUD OFF

• LOUD ON

: Cancels. : Boost low and high frequencies to produce a well-balanced

sound at a low volume level.

AUX ADJ 00 — AUX ADJ 05

: Adjust the auxiliary input level to avoid the sudden increase

of the output level when changing the source to external component connected to the AUX input jack on the control panel.

BEEP

Keypress tone

AMP GAIN *

Amplifier gain control

AM *

AM station

AUX IN *

SRC SELECT

Auxiliary input

Displayed only when the source is “FM.”

• BEEP OFF

• BEEP ON

• LOW POWER

• HIGH POWER

• AM OFF

• AM ON

• AUX OFF

• AUX ON

: Deactivates the keypress tone. : Activates the keypress tone.

: VOLUME 00 – VOLUME 30 (Select if the maximum power

of each speaker is less than 50 W to prevent damaging the speaker.)

: VOLUME 00 – VOLUME 50 : Disable “AM” in source selection.

: Enable “AM” in source selection, [4]. : Disable “AUX IN” in source selection.

: Enable “AUX IN” in source selection, [4].

*4 If you are using a two-speaker system, set the fader level to “00.” *5 The volume level automatically changes to “VOLUME 30” if you change to “LOW POWER” with the volume level

set higher than “VOLUME 30.”

*6 Displayed only when any source other than “AM” is selected. *7 Displayed only when any source other than “AUX IN” is selected.

SETTINGS

More about this unit

Basic operations

Turning on the power

• By pressing SRC button on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power.

General

• If you change the source while listening to a disc, playback stops.

Next time you select “CD” as the playback source,

playback will start from where it had been stopped previously.

• After ejecting a disc, “NO DISC” appears and you cannot operate some of the buttons. Insert another disc or press SRC to select another playback source.

• If no operation is done for about 30 seconds after pressing MENU button, the operation will be canceled.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and the

stations are stored anew.

– When SSM is over, the station stored in the lowest

preset number will be automatically tuned in.

• When storing a station manually, the previously preset station is erased when a new station is stored in the same preset number.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

General

• This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA), MP3/WMA (for KD-R306/KD-R305) formats.

• When a disc is inserted upside down, “PLEASE” and “EJECT” appear alternately on the display. Press 0 to eject the disc.

• KD-R306/KD-R305: MP3 and WMA “tracks” (words “file” and “track” are used interchangeably) are recorded in “folders.”

• KD-R306/KD-R305: While fast-forwarding or reversing on an MP3 or WMA disc, you can only hear intermittent sounds.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• KD-R306/KD-R305: This unit can only play back files of the same type as those detected first if a disc includes both audio CD (CD-DA) files and MP3/WMA files.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, or for the following reasons:

– Discs are dirty or scratched. – Moisture condensation has occurred on the lens

inside the unit.

– The pickup lens inside the unit is dirty.

ENGLISH

Continued on the next page

REFERENCES

– The files on the CD-R/CD-RW are written using the

“Packet Write” method.

– There are improper recording conditions (missing

data, etc.) or media conditions (stained, scratched, warped, etc.).

• CD-RWs may require a longer readout time since the

ENGLISH

reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or a protective seal stuck

to the surface.

– Discs on which labels can be directly printed by an

ink jet printer.

Using these discs under high temperature or high

humidity may cause malfunctions or damage to the unit.

Playing an MP3/WMA disc (for KD-R306/ KD-R305)

• This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

• This unit can show the names of albums, artists (performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or

2.4) for MP3 files and for WMA files.

• This unit can display only one-byte characters. No other characters can be correctly displayed.

• This unit can play back MP3/WMA files meeting the conditions below:

– Bit rate: 8 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) – Disc format: ISO 9660 Level 1/Level 2, Romeo,

Joliet, Windows long file name

• The maximum number of characters for file/folder names vary depending on the disc format used (includes 4 extension characters—<.mp3> or <.wma>).

– ISO 9660 Level 1: up to 12 characters – ISO 9660 Level 2: up to 31 characters – Romeo: up to 128 characters – Joliet: up to 64 characters – Windows long file name: up to 128 characters

• This unit can recognize a total of 512 files, 255 folders, and 8 hierarchical levels.

• This unit can play back files recorded in VBR (variable bit rate).

Files recorded in VBR have a discrepancy in the

elapsed time display, and do not show the actual elapsed time. In particular, this difference becomes noticeable after performing the search function.

• This unit cannot play back the following files:

– MP3 files encoded in MP3i and MP3 PRO format. – MP3 files encoded in an inappropriate format. – MP3 files encoded with Layer 1/2. – WMA files encoded in lossless, professional, and

voice format.

– WMA files which are not based upon Windows

Media ® Audio. – WMA files copy-protected with DRM. – Files which have data such as AIFF, ATRAC3, etc.

• The search function works but search speed is not

constant.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds,

it is automatically inserted into the loading slot again to protect it from dust. Playback starts automatically.

Title assignment

• If you try to assign titles to more than 30 station

frequencies, “NAME FULL” appears. Delete unwanted titles before assignment.

Menu operations

• If you change the “AMP GAIN” setting from

“HIGH POWER” to “LOW POWER” while the volume level is set higher than “VOLUME 30,” the unit automatically changes the volume level to “VOLUME 30.”

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Check the cords and connections.

• The unit does not work at all. Reset the unit (see page 3).

General

• “AUX IN” cannot be selected. Check the “SRC SELECT” page 14).

• SSM automatic presetting does not work. Store stations manually.

• Static noise while listening to the radio. Connect the antenna firmly.

FM/AM

• “AM” cannot be selected. Check the “SRC SELECT” page 14).

• Disc cannot be played back. Insert the disc correctly.

= “AUX IN” setting (see

= “AM” setting (see

ENGLISH

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be

skipped.

• Disc can neither be played back nor ejected. • Unlock the disc (see page 9).

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

Disc playback

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• “PLEASE” and “EJECT“ appear alternately

on the display.

• Insert a finalized CD-R/CD-RW.

• Finalize the CD-R/CD-RW with the component which

you used for recording.

• Eject the disc forcibly (see page 3).

• Change the disc.

• Check the cords and connections.

Press 0, then insert a disc correctly.

Continued on the next page

17REFERENCES

ENGLISH

Symptoms Remedies/Causes

• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file names.

• Noise is generated. Skip to another track or change the disc. (Do not add the extension code <.mp3> or <.wma> to non-MP3 or WMA tracks.)

• A longer readout time is required

(“READING” keeps flashing on the display).

• Tracks do not play back in the order you

have intended them to play.

MP3/WMA playback (for KD-R306/KD-R305)

• The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by

• The correct characters are not displayed

(e.g. album name).

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Do not use too many hierarchical levels and folders.

The playback order is determined when the files are recorded.

how the tracks are recorded on the disc.

This unit can only display letters (upper case), numbers, and a limited number of symbols.

Maintenance

How to clean the connectors

Connectors

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture has evaporated.

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs

Do not use the following discs:

Single CD (8 cm disc) Warped disc

ENGLISH

How to handle discs

When removing a disc from its case, press down the center holder

of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc in its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs in cases after use.

Center holder

Sticker and sticker residue Stick-on label

C-thru Disc (semi-

Unusual shape

Transparent or semi-

transparent parts on its

recording area

transparent disc)

19REFERENCES

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output: Front/Rear: 50 W per channel

ENGLISH

Continuous Power Output (RMS): Front/Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz

at no more than 0.8% total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)

Tone Control Range: Bass: ±12 dB at 100 Hz

Treble: ±12 dB at 10 kHz Frequency Response: 40 Hz to 20 000 Hz Signal-to-Noise Ratio: 70 dB Line-Out Level/Impedance: 2.5 V/20 kΩ load (full scale) Output Impedance: 1 kΩ Other Terminal: AUX (auxiliary) input jack, Antenna input

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 108.0 MHz

AM: 531 kHz to 1 602 kHz

FM Tuner Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)

50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)

Alternate Channel Selectivity (400 kHz): 65 dB

Frequency Response: 40 Hz to 15 000 Hz

Stereo Separation: 30 dB

AM Tuner Sensitivity: 20 μV

Selectivity: 35 dB

CD PLAYER SECTION

Type: Compact disc player Signal Detection System: Non-contact optical pickup

(semiconductor laser) Number of Channels: 2 channels (stereo) Frequency Response: 5 Hz to 20 000 Hz Dynamic Range: 93 dB Signal-to-Noise Ratio: 98 dB Wow and Flutter: Less than measurable limit

For KD-R306/KD-R305:

MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 192 kbps

GENERAL

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance)

Grounding System: Negative ground

Allowable Operating Temperature: 0°C to +40°C

Dimensions (W × H × D): (approx.) Installation Size: 182 mm × 52 mm × 160 mm

ENGLISH

Panel Size: 188 mm × 58 mm × 6 mm

Mass:

Design and specifications are subject to change without notice.

1.3 kg (excluding accessories)

21REFERENCES

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

EN, TH

0808DTSMDTJEIN

KD-R306/KD-R305/KD-R206/KD-R205

Installation/Connection Manual

°“√µ‘¥µ—Èß/§ŸË¡◊Õ°“√µ‘¥µ—Èß

GET0564-006A

[U/UH]

Handles

§—π∫—ß§—∫

Washer (ø5)

ª√–‡°Áπ«ß·À«π

(ø5)

Lock nut (M5)

πÕµ≈ÁÕ§ (M5)

Mounting bolt (M4 × 5 mm; M5 × 12.5 mm)

≈—°µ‘¥ (M4 × 5 ¡¡.; M5 × 12.5 ¡¡.)

A / B Hard case (for KD-R306/KD-R305)/Control panel

≈—ß∫√√®ÿ (”À√—∫

KD-R306

À√◊Õ

KD-R305

)/ÀπÈ“ªí¥

Sleeve

ª≈Õ°ÀÿÈ¡

Trim plate

·ºËπ‚≈À–¢Õ∫·µËß

Power cord

“¬‡§‡∫‘≈°”≈—ß

ENGLISH

Parts list for installation and connection

The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer immediately.

Remote controller

√’‚¡µ§Õπ‚∑√≈

Battery

·∫µ‡µÕ√

0808DTSMDTJEIN

EN, TH

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

Heat sink / ·ºËπ√–∫“¬§«“¡√ÈÕπ

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• It is recommended to connect speakers with a maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 14 of the INSTRUCTIONS).

• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

‰∑¬

™ÿ¥ª√–°Õ∫π’È‰¥È√—∫°“√ÕÕ°·∫∫¡“‡æ◊ËÕ„™Èß“π°—∫√–∫∫ °√–·‰øøÈ““¬¥‘π¢—È«≈∫°√–·µ√ß 12 ‚«≈∑Ï À“°√∂¬πµÏ¢Õß§ÿ≥‰¡ò‰ ¥È„™È√–∫∫π’È µÈÕß„™È‡§√◊ËÕß·ª≈ß°√–·‰ø™Ë«¬ ´÷Ëß“¡“√∂À“´◊ÈÕ‰¥È®“°√È“π¢“¬‡§√◊ËÕß‡’¬ß√∂¬πµÏ

JVC

§”‡µ◊Õπ

‡æ◊ËÕªÈÕß°—π°“√‡°‘¥‰øøÈ“≈—¥«ß®√ ¢Õ·π–π”„ÀÈª≈¥¢—È«·∫µ‡µÕ√’Ë≈∫ÕÕ° ·≈È«®÷ßµËÕ“¬‰ø°ËÕπµ‘¥µ—Èß‡§√◊ËÕß

• µ√«®



Õ∫„ÀÈ·πË„®«Ë“‰¥È‡¥‘π“¬¥‘πµËÕ√–À«Ë“ß‡§√◊ËÕß°—∫µ—«∂—ß √∂¬πµÏ„À¡Ë·≈È«À≈—ß®“°µ‘¥µ—Èß

À¡“¬‡Àµÿ

• „™Èæ‘°—¥®”‡æ“–·∑πøî« À“°øî«Ï¢“¥∫ËÕ¬ „ÀÈª√÷°…“√È“ π¢“¬‡§√◊ËÕß‡’¬ß√∂¬πµÏ JVC

• ¢Õ·π–π”„ÀÈµËÕ≈”‚æß ∑’Ë¡’°”≈—ß¢—∫ßÿ¥‡°‘π°«Ë“ 50 W (∑—Èß¥È“πÀπÈ“·≈–¥È“πÀ≈—ß ¡’§Ë“§«“¡µÈ“π∑“π 4 Ω ∂÷ß 8 Ω)

∂È“°”≈—ß¢—∫µË”°«Ë“

50 W „ÀÈ‡ª≈’Ë¬π§Ë“ “AMP GAIN” ‡æ◊ËÕªÈÕß°—π‰¡Ë„ÀÈ≈”‚æß™”√ÿ¥ (¥ŸÀπÈ“ 14 §”·π–π”)

• °“√ªÈÕß°—π°“√≈—¥«ß®√ ®–µÈÕßæ—π¢—È«“¬µ–°—Ë« ∑’Ë‰¡Ë„™È·≈È«¥È«¬‡∑ ªæ—π“¬‰ø

• ·ºËπ√–∫“¬§«“¡√ÈÕπ®–√ÈÕπ¡“°À≈—ß®“°„™È √–¡—¥√–«—ßÕ¬Ë“‰ª —¡º—‡¡◊ËÕ∂Õ¥™ÿ¥ª√–°Õ∫π’È

¢ÈÕ§«√√–«—ß”À√—∫°“√µËÕ·À≈Ëß®Ë“¬°”≈—ß·≈–≈”‚æß:

•

• °ËÕπ∑’Ë®–µËÕ“¬µ–°—Ë«‡§‡∫‘≈°”≈—ß¢Õß≈”‚æß‡¢È“°—∫≈”‚æß „ÀÈµ√«®Õ∫°“√‡¥‘π“¬‰ø≈”‚æß„π√∂¢Õß§ÿ≥„ÀÈ‡√’¬∫√ÈÕ¬‡’¬°ËÕπ

√“¬°“√Ë«πª√–°Õ∫”À√—∫µ‘¥µ—Èß·≈–‡™◊ËÕ¡µËÕ°—π

Ë«πª√–°Õ∫µËÕ‰ªπ’È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È À“°¡’‘Ëß„¥‰¡Ë§√∫ °√ÿ≥“ª√÷°…“µ—«·∑π®”ÀπË“¬‡§√◊ËÕß‡’¬ßµ‘¥√∂¬πµÏ JVC ‚¥¬∑—π∑’

Rubber cushion

¬“ß°—π°√–·∑°

For KD-R306/KD-R305 / ”À√—∫ KD-R306 À√◊Õ KD-R305

When using the optional stay / ‡¡◊ËÕ„™Èµ—«¬÷¥·∫∫‡≈◊Õ°‰¥È

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are

used, they could damage the unit.

À¡“¬‡Àµ :

‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫≈ß„π·∑Ëπ√Õß√—∫‰«È „ÀÈ„™È°√Ÿ¬“«¢π“¥ 8

¡¡.

∂È“„™È°√Ÿ¬“«°«Ë“π’ÈÕ“®∑”„ÀÈ™ÿ¥ª√–°Õ∫‡’¬À“¬‰¥ô

Bracket*

·∑Ëπ√Õß√—∫*

Pocket

°–‡ª“–

Flat head screws (M5 × 8 mm) *

°√ŸÀ—«‡√’¬∫ (M5 × 8 ¡¡.) *

Screw (option)

°√Ÿ (‡≈◊Õ°‰¥È)

Stay (option)

µ—«¬÷¥ (‡≈◊Õ°‰¥È)

Fire wall

ºπ—ß°—π‰ø

Dashboard

·ºßÀπÈ“ªí∑¡á

Install the unit at an angle of less than 30˚.

µ‘¥µ—Èß™ÿ¥ª√–°Õ∫∑’Ë¡ÿ¡µË”°«Ë“ 30˚ Õß»“

Removing the unit

Before removing the unit, release the rear section.

Insert the two handles, then pull them as illustrated so that the unit can be removed.

„Ë§—π∫—ß§—∫ 2 Õ —π≈ß„π√ËÕß”À√—∫„™Èæ—π≈«¥ ¥—ß¿“æ ®“°π—Èπ „ÀÈ‡≈◊ËÕπ™ÿ¥ª√–°Õ∫ÕÕ° „π¢≥–∑’Ë§ËÕ¬ Ê ¥÷ß§—π∫—ß§—∫∑—Èß Õß Õ—πÕÕ°®“°°—π

Do the required electrical connections.

µËÕ“¬‰øµ“¡∑’Ë°”Àπ¥‰«È∑—ÈßÀ¡¥

Bend the appropriate tabs to hold the sleeve firmly in place.

ßÕ·ºËπ‡æ◊ËÕ¬÷¥ª≈Õ°„ÀÈµËÕ°—π‡¢È“∑’Ë

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

When installing the unit without using the sleeve / ‡¡◊ËÕµ‘¥µ—Èß™ÿ¥ª√–°Õ∫‚¥¬‰¡Ë„™Èª≈Õ°ÀÿÈ¡

In a Toyota car for example, first remove the car radio and install the unit in its place.

µ—«Õ¬Ë“ß‡™Ëπ „π√∂¬πµÏ‚µ‚¬µÈ“ „ÀÈ∂Õ¥«‘∑¬ÿµ‘¥√∂¬πµÏÕÕ°°ËÕπ ·≈ô«®÷ßµ‘¥µíôß‡§√◊ËÕßπ’ô‡¢ô“·∑π∑’Ë

*1 When you stand the unit, be careful not to damage the fuse on the rear. *2 Not supplied for this unit.

°“√µ‘¥µ—Èß

(°“√ª√–°Õ∫·ºßÀπÈ“ªí∑¡Ï‡¢È“)

¿“æµ—«Õ¬Ë“ßµËÕ‰ªπ’È·¥ß∂÷ß°“√µ‘¥µ—Èß·∫∫∑—Ë«‰ª À“°§ÿ≥¡’ªí≠À“À√◊ÕµÈÕß°“√¢ÈÕ¡Ÿ≈‡°’Ë¬«°—∫™ÿ¥µ‘¥µ—Èß °√ÿ≥“ª√÷°…“°—∫ºŸÈ¢“¬‡§√◊ËÕß‡’ ¬ß√∂¬πµÏ

JVC ¢Õß∑Ë“πÀ√◊Õ∫√‘…—

• ™ÿ¥ª√–°Õ∫ ∂È“§ÿ≥‰¡Ë·πË„®«Ë“µ‘¥µ—Èß™ÿ¥ª√–°Õ∫π’È∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë „ÀÈÀ“™Ë“ßºŸÈ‡™’Ë¬«™“≠‡ªìπºŸÈµ‘¥µ—Èß

°“√∂Õ¥™ÿ¥ª√–°Õ∫

°ËÕπ®–∂Õ¥™ÿ¥ª√–°Õ∫ „ÀÈª≈¥ÀπÈ“µ—¥Ë«π∑È“¬°ËÕπ

Flat head screws (M5 × 8 mm) *

°√ŸÀ—«‡√’¬∫ (M5 × 8 ¡¡.) *

Bracket *

·∑Ëπ√Õß√—∫*

‡¡◊ËÕ§ÿ≥µ—Èß™ÿ¥ª√–°Õ∫¢÷Èπ √–«—ßÕ¬Ë“∑”„ÀÈøï«Ï∫√‘‡«≥Ë«π∑È“¬‡’¬À“¬

‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È

For KD-R306/KD-R305 /

”À√—∫ KD-R306 À√◊Õ KD-R305

Typical connections / °“√‡™◊ËÕ¡µËÕ·∫∫ª°µ

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious

damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1 Connect the colored leads of the power cord in the order specified in the illustration below. 2 Connect the antenna cord. 3 Finally connect the wiring harness to the unit.

ENGLISH

ELECTRICAL CONNECTIONS

Not supplied for this unit.

*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the

power cannot be turned on.

Rear line out (see diagram

)

“¬—≠≠“≥ÕÕ°¥È“πÀ≈—ß (¥Ÿ·ºπ¿Ÿ¡ )

Rear ground terminal

®ÿ¥‡™◊ËÕ¡µËÕ “¬¥‘π¥È“πÀ≈—ß

15 A fuse

øî«Ï¢π“¥ 15 A

Antenna terminal

¢—È«“¬Õ“°“»

‰∑¬

°ËÕπ°“√‡™◊ËÕ¡µËÕ: µ√«®¥Ÿ°“√‡¥‘π“¬‰ø„π√∂¬πµÏ„ÀÈ≈–‡Õ’¬¥∂’Ë∂È«π ‡æ√“–°“√‡™◊ËÕ¡µËÕ∑’Ëº‘¥æ≈“¥Õ“®∑”„ÀÈ‡°‘¥§«“¡‡’¬À“¬ √È“¬·√ßµËÕ™ÿ¥ª√–°Õ∫™ÿ¥π’È‰¥È “¬µ–°—Ë«¢Õß“¬‰ø·≈–¢ÕßÕÿª°√≥ÏµËÕ‡™◊ËÕ¡®“°µ—«∂—ß√∂¬πµÏÕ“®¡’’∑’Ë‰¡Ë‡À¡◊Õπ°—π

1 µËÕ“¬‰ø’µ“¡≈”¥—∫∑’Ë√–∫ÿ„π√Ÿª¥È“π≈Ë“ß 2 ‡™◊ËÕ¡µËÕ°—∫“¬Õ“°“» 3 ÿ¥∑È“¬ µËÕË«π§«∫§ÿ¡°“√‡¥‘π“¬‰ø‡¢È“°—∫™ÿ¥ª√–°Õ∫™ÿ¥π’È

°“√‡™◊ËÕ¡‚¥¬„™È‰øøÈ“

To the metallic body or chassis of the car

µËÕ°—∫‚§√ß‚≈À–À√◊Õ‡™´‘¢Õß√∂¬πµú

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

µËÕ°—∫¢—È«∑’Ë¡’°√–·‰øøÈ“„π·ºßøî«Ï ´÷ËßµËÕ°—∫·∫µ‡µÕ√’Ë√∂¬πµ

( ‚¥¬‰¡ËµÈÕß„™È«‘∑™Ï®ÿ¥√–‡∫‘¥) (12 ‚«≈∑Ï§ß∑’Ë)

To an accessory terminal in the fuse block

µËÕ°—∫¢—È«Ë«πª√–°Õ∫„π·ºßøî«

Black

’¥”

Red

’·¥ß

Yellow *

’‡À≈◊Õß *

Ignition switch

«‘∑™Ï®ÿ¥√–‡∫‘¥

Fuse block

·ºßøî«

Purple

’¡Ë«ß

Purple with black stripe

’¡Ë«ß·∂∫¥”

Green

’‡¢’¬«

Green with black stripe

’‡¢’¬«·∂∫¥”

Gray

’‡∑“

Gray with black stripe

’‡∑“·∂∫¥”

White

’¢“«

White with black stripe

’¢“«·∂∫¥”

Right speaker (rear)

≈”‚æß¢«“ (À≈—ß)

Left speaker (rear)

≈”‚æß´È“¬ (À≈—ß)

Right speaker (front)

≈”‚æß¢«“ (ÀπÈ“)

Left speaker (front)

≈”‚æß´È“¬ (ÀπÈ“)

‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È

°ËÕπ°“√µ√«®Õ∫°“√∑”ß“π¢Õß™ÿ¥ª√–°Õ∫π’È°ËÕπ∑’Ë®–µ‘¥µ—Èß µÈÕßµËÕ“¬µ–°—Ë«π’È°ËÕπ

Blue with white stripe

’πÈ”‡ß‘π≈“¬¢“«

To the remote lead of other equipment (200 mA max.)

µËÕ‡¢È“°—∫Õª°√≥ÏÕË◊π (¢π“¥Ÿß¸¥ 200 mA)

To the automatic antenna if any (250 mA max.)

‡“Õ“°“»‰øøÈ“Õ—µ‚π¡—µ‘ À“°¡’ (¢π“¥Ÿß¸¥ 250 mA)

Blue

»’øÈ“

Connecting the external amplifier / °“√‡™◊ËÕ¡µËÕ‡§√◊ËÕß¢¬“¬‡’¬ß¿“¬πÕ°

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with

paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

§ÿ≥“¡“√∂µËÕ°—∫·Õ¡æ≈‘ø“¬‡ÕÕ√Ï ‡æ◊ËÕ‡æ‘Ë¡§ÿ≥ ¿“æ‡’¬ß„ÀÈ°—∫√–∫∫‡µÕ√‘‚Õ¢Õß√∂¬πµÏ

• µËÕ“¬µ–°—Ë«√–¬–‰°≈ (’πÈ”‡ß‘π≈“¬¢“«) ‡¢È“°—∫“¬µ–°—Ë«√–¬–‰°≈¢ÕßÕÿª°√≥ÏÕ◊Ëπ Ê ‡æ◊ËÕ®–“¡“√∂§«∫§ÿ¡‚¥¬™ÿ¥ª√–

°Õ∫π’È‰¥È

• ∂Õ¥≈”‚æßÕÕ°®“°™ÿ¥ª√–°Õ∫π’È ·≈È«µËÕ‡¢È“°—∫‡§√◊ËÕß¢¬“¬ ∑‘Èß“¬µ–°—Ë«≈”‚æß¢Õß™ÿ¥ª√–°Õ∫π’È‰«È

Rear speakers

≈”‚æßÀ≈—ß

Remote lead

“¬µ–°—Ë«•–¬–‰°•

Remote lead (blue with white stripe)

“¬µ–°—Ë«•–¬–‰°• (’πÈ”‡ß‘π≈“¬¢“«)

To the remote lead of other equipment or automatic antenna if any

µËÕ“¬°—∫Õÿª°√≥ÏÕ◊ËπÀ√◊Õ‡“Õ“°“»Õ—µ‚π¡—µ‘∂È“¡’

Y-connector (not supplied for this unit)

¢ÈÕµËÕ√Ÿªµ—« Y ( ‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)

Front speakers

≈”‚æßÀπÈ“

JVC Amplifier

‡§√◊ËÕß¢¬“¬‡’¬ß JVC

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds.

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all.

* Have you reset your unit?

°“√µ√«®Õ∫ªí≠À“¢—¥¢ÈÕß

• øî«Ï¢“¥

* ¡’°“√‡™◊ËÕ¡ “¬µ–°—Ë«’¥”·≈–’·¥ßÕ¬Ë“ß∂Ÿ°µÈÕßÀ√◊Õ‰¡Ë

• ‰¡Ë“¡“√∂‡ª‘¥‡§√◊ËÕß‰¥È

* ¡’°“√‡™◊ËÕ¡“¬µ–°—Ë«’‡À≈◊ÕßÀ√◊Õ‰¡Ë

• ‰¡Ë¡’‡’¬ßÕÕ°®“°≈”‚æß

* “¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æß‡°‘¥‰øøÈ“≈—¥«ß®√À√◊Õ‰¡Ë

• ‡’¬ß‡æ’È¬π

* “¬µ–°—Ë«Ë«π∑’ËÕÕ°∑“ß≈”‚æßµËÕ≈ß¥‘πÀ√◊Õ‰¡Ë * “¬¢—È«≈∫ “–” ¢Õß≈”‚æß¥È“π´È“¬·≈–¢«“µËÕ≈ß¥‘πµ“¡ª°µ‘À√◊Õ‰¡Ë

• ‡’¬ß√∫°«π

* ¡’°“√„™È“¬—ÈπÊ À√◊ÕÀπ“Ê µËÕ®“°‡§√◊ËÕß«π∑’Ëµ‘¥µ—Èß ‰«È∫πæ◊Èπ¥È“πÀ≈—ß°—∫µ—«∂—ß√∂¬πµÏÀ√◊Õ‰¡Ë

• ™ÿ¥ª√–°Õ∫√ÈÕπ¢÷Èπ

• ‡§√◊ËÕß√—∫π’È∑”ß“π‰¡

* ∑Ë“π‰¥Èµ—Èß‡§√◊ËÕß„À¡Ë·≈È«À√◊Õ¬—ß

Signal cord (not supplied for this unit)

“¬‡§‡∫‘≈—≠≠“≥ ( ‰¡Ë‰¥È„ÀÈ¡“°—∫™ÿ¥ª√–°Õ∫π’È)

µËÕ≈«¥“¬¥‘π„ÀÈ·πËπ‡¢È“°—∫µ—«∂—ß‡À≈Á° À√◊Õµ—«∂—ß√∂—µ√ßË«π ∑’Ë‰¡Ë¡’’‡§≈◊Õ∫ (À“°¡’’‡§≈◊Õ∫Õ¬ŸË „ÀÈ¢Ÿ¥’ÕÕ°°ËÕπ °ËÕπµËÕ≈«¥“¬¥‘π) À“°‰¡ËªØ‘∫—µ‘µ“¡§”·π–π”π’È ‡§√◊ËÕßÕ“®™”√ÿ¥À√◊Õ‡’¬À“¬‰¥

KD-R306/KD-R305/KD-R206/KD-R205

Installation/Connection Manual

安裝/連接手冊

GET0564-010A

[UT]

ENGLISH

WARNINGS

To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car’s chassis again after installation.

Notes:

• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• To prevent short circuits, cover the terminals of the UNUSED leads with insulating tape.

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

Heat sink / 散熱片

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit

will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

0808DTSMDTJEIN

EN, CT

中文

本機僅可使用直流 12 V、負極接地的電源系統。如果您的車輛沒有這一電源系統，則需要一個電壓變換器，可以在 JVC 汽車音響分銷商處買到。

警告

為防止短路，建議在安裝本機之前，拔開電池的負極，並把所有電路都連接好。

• 安裝完畢後務必將本機的地線重新接至車身。

注意：

•

把保險絲更換為額定負荷值的保險絲。如果保險絲經常燒壞，請向 JVC 汽車音響分銷商詢問。

• 後置和前置揚聲器的最大輸入功率應大於 50 W，其阻抗為 4  - 8 。如果最大功率小於 50 W，請調校“AMP GAIN”設定值，以防止揚聲器損壞。（參閱使用說明書的第

• 為防止電源短路，請用絕緣帶包住未使用電線的端子。

•

本機使用後，散熱片會很熱。因此，在移出本機時，小心不要觸摸散熱片。

電源和揚聲器接線注意事項：

• 切勿把揚聲器導線接頭接至電池，否則本機將會嚴重損壞。

•

在把揚聲器導線接頭接至揚聲器之前，檢查您汽車上的揚聲器線路。

頁。）

Parts list for installation and connection

The following parts are provided for this unit. If any item is missing, consult your JVC car audio dealer immediately.

A / B Hard case (for KD-R306/KD-R305)/Control panel 硬盒（對應

Washer (ø5) 墊圈（ø5）

KD-R306/KD-R305

）∕控制面板

Handles

板條型把手

Lock nut (M5) 鎖定螺母（M5）

Sleeve

外套機殼

Mounting bolt (M4 × 5 mm; M5 × 12.5 mm) 緊固螺栓（M4 × 5 mm; M5 × 12.5 mm）

For KD-R306/KD-R305 / 對應 KD-R306/KD-R305

Remote controller

遙控器

用於安裝和連接的零件清單

下列零件隨本機提供。若有任何遺漏，立刻咨詢您的 JVC 汽車音響經銷商。

Trim plate

裝飾框

Battery

電池

Power cord

電路連接用的配線束

Rubber cushion

橡膠防震墊

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a typical installation. If you have any questions or require information regarding installation kits, consult your JVC car audio dealer or a company supplying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

安裝（裝設、固定在儀表板內）

下面的圖解表示了典型的安裝程序。如果您有問題，或需要有關配套元件的資料，請向 JVC 汽車音響分銷商或配套元件供應公司詢問。

• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。

Do the required electrical connections.

進行所需的電路連接。

For KD-R306/KD-R305 / 對應 KD-R306/KD-R305

Bend the appropriate tabs to hold the sleeve firmly in place.

弄彎機殼的突舌，把外套機殼牢固在儀表板內。

Removing the unit

Before removing the unit, release the rear section.

When using the optional stay / 若選用支撐架

Fire wall

防火板

Dashboard

儀表板

Stay (option)

支撐架（選用的）

Screw (option)

螺絲釘（選用的）

拆卸本機

在拆卸本機前，應將本機後部的固定和連接部分鬆開。

Insert the two handles, then pull them as illustrated so that the unit can be removed.

按圖所示，將兩片板條型把手插入卡槽，然後輕穩地從兩側向外拉兩片把手，本機隨之拉出。

When installing the unit without using the sleeve / 若不使用外套機殼安裝本機

In a Toyota car for example, first remove the car radio and install the unit in its place. 以豐田牌（TOYOTA）汽車為例：首先取出汽車收音機，然後將本機裝入其空出的位置。

Flat head screws (M5 × 8 mm) 平頭螺絲釘（M5 × 8 mm）*

Bracket*

托座 *

Pocket

空殼

Flat head screws (M5 × 8 mm) * 平頭螺絲釘（M5 × 8 mm）*

Bracket *

托座*

Install the unit at an angle of less than 30˚.

將本機安裝在少於 30˚ 的角度。

*1 When you stand the unit, be careful not to damage the fuse on the rear. *2 Not supplied for this unit.

Note : When installing the unit on the mounting bracket, make sure to use the 8 mm-long screws. If longer screws are used, they

could damage the unit.

注意：把本機安裝在托座上時，務必使用 8 mm 長的螺絲釘。如使用過長的螺絲釘，會損壞本機。

您豎起本機時，小心不要損壞底部的保險絲。

不隨本機提供。

ENGLISH

中文

ELECTRICAL CONNECTIONS

Typical connections / 典型的接線方法

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious

damage to this unit. The leads of the power cord and those of the connector from the car body may be different in color.

1 Connect the colored leads of the power cord in the order specified in the illustration below. 2 Connect the antenna cord. 3 Finally connect the wiring harness to the unit.

Antenna terminal

天線端子

Rear line out (see diagram

本機後背線性輸出端子（參閱圖表）

)

Rear ground terminal

本機後背接地端子

Black

黑色

Yellow

黃色 *

15 A fuse 15 A 保險絲

電路連接

接線前：仔細檢查汽車內的線路。不正確的接線會導致本機嚴重損壞。

電源線的引線和車身的連接器引線在顏色上可能有所不同。

1 依照下圖所示之次序連接電源線的顏色導線。

2 將天線的電線連接起來。

3 最後，把配線束的插頭插在本機上。

To the metallic body or chassis of the car

接至金屬體或汽車底盤

To a live terminal in the fuse block connecting to the car battery (bypassing the ignition switch) (constant 12 V)

接至保險絲單元內的帶電端子，保險絲單元與車裝電池相連接（用於旁路點火開關）（恆定 12 V）

Ignition switch

點火開關

White with black stripe

白色帶有黑色條紋

White

白色

Left speaker (front)

左揚聲器（前置）

Gray with black stripe

灰色帶有黑色條紋

Red

紅色

Blue

藍色

Blue with white stripe

藍色帶有白色條紋

Gray

灰色

Right speaker (front)

右揚聲器（前置）

To an accessory terminal in the fuse block

接至保險絲單元內的附屬端子

To the automatic antenna if any (250 mA max.) 接至自動天線（若有裝設）（最大 250 mA）

Green with black stripe

綠色帶有黑色條紋

Green

綠色

To the remote lead of other equipment (200 mA max.) 連接至其他裝置上的遙控導線（最大 200 mA）

Purple with black stripe

紫色帶有黑色條紋

Left speaker (rear)

左揚聲器（後置）

Fuse block

保險絲單元

Purple

紫色

Right speaker (rear)

右揚聲器（後置）

Not supplied for this unit.

*2 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the

power cannot be turned on.

不隨本機提供。

本機未安裝時，進行工作狀況檢查之前，必須把這導線接上，否則不能開啟電源。

Connecting the external amplifier / 連接至外部功率放大器

You can connect an amplifier to upgrade your car stereo system.

• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.

• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.

您可以連接功率放大器以提昇尊車的音響系統。

•

將遙控導線（藍色帶有白色條紋）和其他裝置上的遙控導線連接起來，以便可以經由本機進行遙控。

• 將揚聲器和本機拔開，再接上功率放大器。將本機的揚聲器接線放置不用。

Rear speakers

後置揚聲器

Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with

paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.

JVC Amplifier

JVC 功率放大器

Signal cord (not supplied for this unit)

信號導線（不隨本機提供）

Remote lead

遙控導線

Remote lead (blue with white stripe)

遙控導線（藍色帶有白色條紋）

將地線與金屬車體或者汽車底盤緊密連接，連接處應該沒有被油漆覆蓋（如果已塗上油漆，在連接電

線前，將油漆刮去）。如果不這樣做，可能會損壞本機。

Y-connector (not supplied for this unit) Y-型連接導線（不隨本機提供）

To the remote lead of other equipment or automatic antenna if any

連接至其他裝置上的遙控導線或自動天線（若有裝設）

Front speakers

前置揚聲器

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the speaker output lead short-circuited?

• Sound is distorted.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• Noise interfere with sounds.

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the speaker output lead grounded? * Are the “–” terminals of L and R speakers grounded in common?

• This unit does not work at all.

* Have you reset your unit?

故障排除

• 保險絲燒斷。

* 檢查紅色導線接頭和黑色導線接頭是否接觸正確？

• 電源不能接通。

* 檢查黃色導線接頭是否接上？

• 揚聲器沒有聲音。

* 檢查揚聲器輸出導線接頭是否短路？

• 聲音失真。

* 檢查揚聲器輸出端子是否接地？ * 檢查揚聲器的左（L）、右（R）端子的負極“–”是否共同接地？

• 噪音干擾音響。

* 後接地端子與車身是否使用較短和較厚的電線連接？

• 本機發熱。

* 檢查揚聲器輸出端子是否接地？ * 檢查揚聲器的左（L）、右（R）端子的負極“–”是否共同接地？

• 本機完全不能操作。

* 您是否已經重置您的機組？

Selecting a preset sound mode

You can select a preset sound mode suitable to the music genre.

• See also page 13 (“EQ”).

Selecting from Menu.

[Turn] = [Press]

Select “EQ”

Storing your own sound mode

You can store your own adjustments in memory.

1 Select “USER” for “EQ.”

[Turn] = [Press]

Select “EQ” = “USER”

2 While “USER” is shown on the display...

ENGLISH

Preset value setting for each sound mode

Preset values

Indication (For) USER (Flat sound) 00 00 OFF ROCK (Rock or disco music)

CLASSIC (Classical music) +01 –02 OFF POPS (Light music) +04 +01 OFF HIP HOP (Funk or rap music) +02 00 ON JAZZ (Jazz music) +02 +03 OFF

BASS

+03 +01 ON

TREBLE

LOUD

• If no operation is done for about 30 seconds, the operation will be canceled.

3 Select a tone.

[Turn] = [Press]

BASS Ô TREBLE

4 Adjust the level.

Tone Level BASS –06 to +06 TREBLE –06 to +06

To return to the previous menu, press BACK.

5 Finish the procedure.

SETTINGS

Title assignment

You can assign titles to 30 station frequencies (FM and AM) using 8 characters (maximum) for each title.

1 Select “FM” or “AM.”

ENGLISH

2 Show the title entry screen.

3 Assign a title.

1 Select a character.

2 Move to the next (or previous) character

position.

3 Repeat steps 1 and 2 until you finish

entering the title.

4 Finish the procedure.

To erase the entire title

In step 2 above...

Menu operations

1 2 3 Repeat step 2 if necessary.

[Turn] = [Press]

Category Menu items Selectable settings, [reference page]

• To return to the previous menu, press BACK.

Initial: Underlined

ENGLISH

DEMO

Display

DEMO

demonstration

CLOCK DISP *

Clock display

CLOCK

CLOCK SET

Clock setting

Equalizer

DIMMER

Dimmer

SCROLL*

Scroll

DISPLAY

• DEMO ON

: Display demonstration will be activated automatically if no

operation is done for about 20 seconds, [7].

• DEMO OFF

• CLOCK ON

: Cancels.

: Clock time is shown on the display at all times when the

power is turned off.

• CLOCK OFF

: Cancels; pressing DISP will show the clock time for about 5

seconds when the power is turned off, [7].

: Adjust the hour, then the minute, [7]. [Initial: 1:00]

: Select a preset sound mode suitable to the music genre. USER, ROCK, CLASSIC, POPS, HIP HOP, JAZZ

• DIMMER ON

• DIMMER OFF

• SCROLL ONCE

• SCROLL AUTO

• SCROLL OFF

: Dims the display and button illumination. : Cancels.

: Scrolls the displayed information once. : Repeats scrolling (at 5-second intervals).

: Cancels. Pressing DISP for more than one second can scroll the display regardless of the setting.

TAG DISPLAY

Tag display

• TAG ON

• TAG OFF

(For KD-R306/ KD-R305)

If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select

“CLOCK OFF” to save the car’s battery.

Some characters or symbols will not be shown correctly (or will be blanked) on the display.

: Shows the Tag information while playing MP3/WMA tracks.

: Cancels.

Continued on the next page

SETTINGS

Category Menu items Selectable settings, [reference page]

ENGLISH

TUNER

AUDIO

MONO *

Monaural mode

IF BAND

Intermediate frequency band

FADER*

Fader

BALANCE Balance

LOUD

Loudness

AUX ADJUST

Auxiliary input level adjustment

• MONO ON

: Activate monaural mode to improve FM reception, but stereo

effect will be lost, [8].

• MONO OFF

• AUTO

: Restore the stereo effect.

: Increases the tuner selectivity to reduce interference noises

between adjacent stations. (Stereo effect may be lost.)

• WIDE

: Subject to interference noises from adjacent stations, but

sound quality will not be degraded and the stereo effect will remain.

R06 – F06 : Adjust the front and rear speaker output balance.

[Initial: 00]

L06 – R06 : Adjust the left and right speaker output balance.

[Initial: 00]

• LOUD OFF

• LOUD ON

: Cancels. : Boost low and high frequencies to produce a well-balanced

sound at a low volume level.

AUX ADJ 00 — AUX ADJ 05

: Adjust the auxiliary input level to avoid the sudden increase

of the output level when changing the source to external component connected to the AUX input jack on the control panel.

BEEP

Keypress tone

AMP GAIN *

Amplifier gain control

AM *

AM station

AUX IN *

SRC SELECT

Auxiliary input

Displayed only when the source is “FM.”

• BEEP OFF

• BEEP ON

• LOW POWER

• HIGH POWER

• AM OFF

• AM ON

• AUX OFF

• AUX ON

: Deactivates the keypress tone. : Activates the keypress tone.

: VOLUME 00 – VOLUME 30 (Select if the maximum power

of each speaker is less than 50 W to prevent damaging the speaker.)

: VOLUME 00 – VOLUME 50

: Disable “AM” in source selection. : Enable “AM” in source selection, [4].

: Disable “AUX IN” in source selection. : Enable “AUX IN” in source selection, [4].

*4 If you are using a two-speaker system, set the fader level to “00.” *5 The volume level automatically changes to “VOLUME 30” if you change to “LOW POWER” with the volume level

set higher than “VOLUME 30.”

*6 Displayed only when any source other than “AM” is selected. *7 Displayed only when any source other than “AUX IN” is selected.

SETTINGS

More about this unit

Basic operations

Turning on the power

• By pressing SRC button on the unit, you can also turn on the power. If the source is ready, playback also starts.

Turning off the power

• If you turn off the power while listening to a track, playback will start from where it had been stopped previously next time you turn on the power.

General

• If you change the source while listening to a disc, playback stops.

Next time you select “CD” as the playback source,

playback will start from where it had been stopped previously.

• After ejecting a disc, “NO DISC” appears and you cannot operate some of the buttons. Insert another disc or press SRC to select another playback source.

• If no operation is done for about 30 seconds after pressing MENU button, the operation will be canceled.

Tuner operations

Storing stations in memory

• During SSM search...

– All previously stored stations are erased and the

stations are stored anew.

– When SSM is over, the station stored in the lowest

preset number will be automatically tuned in.

• When storing a station manually, the previously preset station is erased when a new station is stored in the same preset number.

Disc operations

Caution for DualDisc playback

• The Non-DVD side of a “DualDisc” does not comply with the “Compact Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product may not be recommended.

General

• This unit has been designed to reproduce CDs/CD Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD (CD-DA), MP3/WMA (for KD-R306/KD-R305) formats.

• When a disc is inserted upside down, “PLEASE” and “EJECT” appear alternately on the display. Press 0 to eject the disc.

• KD-R306/KD-R305: MP3 and WMA “tracks” (words “file” and “track” are used interchangeably) are recorded in “folders.”

• KD-R306/KD-R305: While fast-forwarding or reversing on an MP3 or WMA disc, you can only hear intermittent sounds.

Playing a CD-R or CD-RW

• Use only “finalized” CD-Rs or CD-RWs.

• KD-R306/KD-R305: This unit can only play back files of the same type as those detected first if a disc includes both audio CD (CD-DA) files and MP3/WMA files.

• This unit can play back multi-session discs; however, unclosed sessions will be skipped while playing.

• Some CD-Rs or CD-RWs may not play back on this unit because of their disc characteristics, or for the following reasons:

– Discs are dirty or scratched. – Moisture condensation has occurred on the lens

inside the unit.

– The pickup lens inside the unit is dirty.

ENGLISH

Continued on the next page

REFERENCES

– The files on the CD-R/CD-RW are written using the

“Packet Write” method.

– There are improper recording conditions (missing

data, etc.) or media conditions (stained, scratched, warped, etc.).

• CD-RWs may require a longer readout time since the

ENGLISH

reflectance of CD-RWs is lower than that of regular CDs.

• Do not use the following CD-Rs or CD-RWs: – Discs with stickers, labels, or a protective seal stuck

to the surface.

– Discs on which labels can be directly printed by an

ink jet printer.

Using these discs under high temperature or high

humidity may cause malfunctions or damage to the unit.

Playing an MP3/WMA disc (for KD-R306/ KD-R305)

• This unit can play back MP3/WMA files with the extension code <.mp3> or <.wma> (regardless of the letter case—upper/lower).

• This unit can show the names of albums, artists (performer), and Tag (Version 1.0, 1.1, 2.2, 2.3, or

2.4) for MP3 files and for WMA files.

• This unit can display only one-byte characters. No other characters can be correctly displayed.

• This unit can play back MP3/WMA files meeting the conditions below:

– Bit rate: 8 kbps — 320 kbps – Sampling frequency: 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1) 24 kHz, 22.05 kHz, 16 kHz (for MPEG-2) – Disc format: ISO 9660 Level 1/Level 2, Romeo,

Joliet, Windows long file name

• The maximum number of characters for file/folder names vary depending on the disc format used (includes 4 extension characters—<.mp3> or <.wma>).

– ISO 9660 Level 1: up to 12 characters – ISO 9660 Level 2: up to 31 characters – Romeo: up to 128 characters – Joliet: up to 64 characters – Windows long file name: up to 128 characters

• This unit can recognize a total of 512 files, 255 folders, and 8 hierarchical levels.

• This unit can play back files recorded in VBR (variable bit rate).

Files recorded in VBR have a discrepancy in the

elapsed time display, and do not show the actual elapsed time. In particular, this difference becomes noticeable after performing the search function.

• This unit cannot play back the following files:

– MP3 files encoded in MP3i and MP3 PRO format. – MP3 files encoded in an inappropriate format. – MP3 files encoded with Layer 1/2. – WMA files encoded in lossless, professional, and

voice format.

– WMA files which are not based upon Windows

Media ® Audio. – WMA files copy-protected with DRM. – Files which have data such as AIFF, ATRAC3, etc.

• The search function works but search speed is not

constant.

Ejecting a disc

• If the ejected disc is not removed within 15 seconds,

it is automatically inserted into the loading slot again to protect it from dust. Playback starts automatically.

Title assignment

• If you try to assign titles to more than 30 station

frequencies, “NAME FULL” appears. Delete unwanted titles before assignment.

Menu operations

• If you change the “AMP GAIN” setting from

“HIGH POWER” to “LOW POWER” while the volume level is set higher than “VOLUME 30,” the unit automatically changes the volume level to “VOLUME 30.”

Troubleshooting

What appears to be trouble is not always serious. Check the following points before calling a service center.

Symptoms Remedies/Causes

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.

• Check the cords and connections.

• The unit does not work at all. Reset the unit (see page 3).

General

• “AUX IN” cannot be selected. Check the “SRC SELECT” page 14).

• SSM automatic presetting does not work. Store stations manually.

• Static noise while listening to the radio. Connect the antenna firmly.

FM/AM

• “AM” cannot be selected. Check the “SRC SELECT” page 14).

• Disc cannot be played back. Insert the disc correctly.

= “AUX IN” setting (see

= “AM” setting (see

ENGLISH

• CD-R/CD-RW cannot be played back.

• Tracks on the CD-R/CD-RW cannot be

skipped.

• Disc can neither be played back nor ejected. • Unlock the disc (see page 9).

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.

Disc playback

• “NO DISC” appears on the display. Insert a playable disc into the loading slot.

• “PLEASE” and “EJECT“ appear alternately

on the display.

• Insert a finalized CD-R/CD-RW.

• Finalize the CD-R/CD-RW with the component which

you used for recording.

• Eject the disc forcibly (see page 3).

• Change the disc.

• Check the cords and connections.

Press 0, then insert a disc correctly.

Continued on the next page

17REFERENCES

ENGLISH

Symptoms Remedies/Causes

• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet.

• Add the extension code <.mp3> or <.wma> to the file names.

• Noise is generated. Skip to another track or change the disc. (Do not add the extension code <.mp3> or <.wma> to non-MP3 or WMA tracks.)

• A longer readout time is required

(“READING” keeps flashing on the display).

• Tracks do not play back in the order you

have intended them to play.

MP3/WMA playback (for KD-R306/KD-R305)

• The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by

• The correct characters are not displayed

(e.g. album name).

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Do not use too many hierarchical levels and folders.

The playback order is determined when the files are recorded.

how the tracks are recorded on the disc.

This unit can only display letters (upper case), numbers, and a limited number of symbols.

Maintenance

How to clean the connectors

Connectors

Moisture condensation

Moisture may condense on the lens inside the unit in the following cases:

• After starting the heater in the car.

• If it becomes very humid inside the car. Should this occur, the unit may malfunction. In this case, eject the disc and leave the unit turned on for a few hours until the moisture has evaporated.

To keep discs clean

A dirty disc may not play correctly. If a disc does become dirty, wipe it with a soft cloth in a straight line from center to edge.

• Do not use any solvents (for example, conventional record cleaner, spray, thinner, benzine, etc.) to clean discs.

To play new discs

Do not use the following discs:

Single CD (8 cm disc) Warped disc

ENGLISH

How to handle discs

When removing a disc from its case, press down the center holder

of the case and lift the disc out, holding it by the edges.

• Always hold the disc by the edges. Do not touch its recording surface.

When storing a disc in its case, gently insert the disc around the center holder (with the printed surface facing up).

• Make sure to store discs in cases after use.

Center holder

Sticker and sticker residue Stick-on label

C-thru Disc (semi-

Unusual shape

Transparent or semi-

transparent parts on its

recording area

transparent disc)

19REFERENCES

Specifications

AUDIO AMPLIFIER SECTION

Maximum Power Output: Front/Rear: 50 W per channel

ENGLISH

Continuous Power Output (RMS): Front/Rear: 19 W per channel into 4 Ω, 40 Hz to 20 000 Hz

at no more than 0.8% total harmonic distortion.

Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)

Tone Control Range: Bass: ±12 dB at 100 Hz

Treble: ±12 dB at 10 kHz

Frequency Response: 40 Hz to 20 000 Hz

Signal-to-Noise Ratio: 70 dB

Line-Out Level/Impedance: 2.5 V/20 kΩ load (full scale)

Output Impedance: 1 kΩ

Other Terminal: AUX (auxiliary) input jack, Antenna input

TUNER SECTION

Frequency Range: FM: 87.5 MHz to 108.0 MHz

AM: 531 kHz to 1 602 kHz

FM Tuner Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)

50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)

Alternate Channel Selectivity (400 kHz): 65 dB

Frequency Response: 40 Hz to 15 000 Hz

Stereo Separation: 30 dB

AM Tuner Sensitivity: 20 μV

Selectivity: 35 dB

CD PLAYER SECTION

Type: Compact disc player

Signal Detection System: Non-contact optical pickup

(semiconductor laser)

Number of Channels: 2 channels (stereo)

Frequency Response: 5 Hz to 20 000 Hz

Dynamic Range: 93 dB

Signal-to-Noise Ratio: 98 dB

Wow and Flutter: Less than measurable limit

For KD-R306/KD-R305:

MP3 Decoding Format: (MPEG1/2 Audio Layer 3) Max. Bit Rate: 320 kbps

WMA (Windows Media® Audio) Decoding Format: Max. Bit Rate: 192 kbps

GENERAL

Power Requirement: Operating Voltage: DC 14.4 V (11 V to 16 V allowance)

Grounding System: Negative ground

Allowable Operating Temperature: 0°C to +40°C

Dimensions (W × H × D): (approx.) Installation Size: 182 mm × 52 mm × 160 mm

ENGLISH

Panel Size: 188 mm × 58 mm × 6 mm

Mass:

Design and specifications are subject to change without notice.

1.3 kg (excluding accessories)

21REFERENCES

Having TROUBLE with operation?

Please reset your unit

Refer to page of How to reset your unit

Ada MASALAH dengan cara

pengoperasian?

Setel kembali unit Anda

Lihat halaman mengenai Bagaimana mereset unit anda

EN, IN

0808DTSMDTJEIN

JVC GET0564-006A, GET0564-010A, GET0564-001A, GET0568-003A, GET0568-010A Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual