JVC GD-V4200PCE, GD-V4200PCE-G, GD-V4200PZW, GD-V4200PZW-G, GD-V4200PZW-GA Service manual & schematics

...

Page 1

JVG SERVICE MANUAL

42" PLASMA DISPLAY MONITOR

NV-PD4200

BASIC CHASSIS
P1

Supplementary

These models corresponded to the printed circuit board exchange in the PDP unit. Therefore, this service manual describes only the information relevant to it.

For details other than those described in this manual, please refer to the NV-PD4200 service manual (No.51732 Apr. 2000).


1.	CONFIRMING THE MODEL NAME, SERIAL NUMBER, ID NUMBER AND CODE NUMBER
2.	MAIN PARTS LOCATION 2
3.	INSPECTION OF COMPONENTS ON THE PW BOARD 3
4.	DISASSEMBLY PROCEDURE 7
5.	CONFIRMING REFERENCE VOLTAGE 8
6.	ADJUSTMENTS 9
7.	PARTS LIST 10

NOTES AT THE TIME OF PW BOARD EXCHANGE -

It will become the cause of failure if dust adheres to the inside of a connector, or a flat wire and a point-of-contact part.

When the PW board is exchanged, be careful of the dust and dirt of the inside of a connector, or a flat wire and a point-of-contact part enough

Page 2

■CONFIRMING MODEL NAME, SERIAL NUMBER, ID NUMBER AND CODE NUMBER

MAIN PARTS LOCATION

Page 3

■INSPECTION OF COMPONENTS ON THE PW BOARD

Diagnose the PW board in PDP unit by checking defects based on the following items.

1. INSPECTION OF FUSES

Measure the resistance of each fuse with a circuit tester, and check OK or NG.

2. INSPECTION OF ALARM LINES

According to the following procedures, measure with a circuit tester and check OK or NG.

2.1 The conduction between the pin 30 of the connector [CN4] and GND on the SIGNAL RELAY PWB (upper left)

2.2 The conduction between the pin 30 of the connector [CN5] and GND on the SIGNAL RELAY PWB (lower right)

2.3 The conduction between the pins of CN3 on the scan IC [A]

2.4 The conductio n betwee n the pins of CN3 on the scan IC [D]

(No.51732B)3

Page 4

3. INSPECTION OF DATA ICS

According to the following procedures, measure with a circuit tester and check OK or NG.

4. INSPECTION OF POWER ICS

According to the following procedures, measure with a circuit tester and check OK or NG.

Page 5

Page 6

5. INSPECTION OF SCAN IC DRIVERS

According to the following procedures, measure with a circuit tester and check OK or NG.

Page 7

DISASSEMBLY PROCEDURE

1. Removing the COMMON PWB
- (1) Detach the 7 connectors.
- (2) Remove the 9 screws [A].
- (3) Remove the COMMON PWB.
2. Removing the DIGITAL PWB
- (1) Detach the 7 connectors.
- (2) Remove the 8 screws [B].
- (3) Remove the DIGITAL PWB.
3. Removing the SCAN PWB
- (1) Detach the 11 connectors.
- (2) Remove the 8 screws [C]
- (3) Remove the SCAN PWB.
4. Removing the SIGNAL RELAY PWB (upper left)
- (1) Detach the 6 connectors.
- (2) Remove the SIGNAL RELAY PWB (upper left).

5. Removing the SIGNAL RELAY PWB (upper right)(1) Detach the 7 connectors.
- (2) Remove the SIGNAL RELAY PWB (upper right).
6. Removing the SIGNAL RELAY PWB (lower left)(1) Detach the 6 connectors.
- (2) Remove the SIGNAL RELAY PWB (lower left).
Removing the SIGNAL RELAY PWB (lower right) (1) Detach the 7 connectors.
- (2) Remove the SIGNAL RELAY PWB (lower right).

Notes : Check the state of the detached cables and connectors.

(1) Check any dirt or peeling in the contact part of the flat cable, and any crack, crease, disconnection and short-circuit of wires.
(2) Check any foreign substance in the connector's contact.
(3) Check the state of plugging the flat cable into the connector, and confirm it locks completely.

Page 8

■ CONFIRMING REFERENCE VOI TAGE

Each PDP panel has the characteristic voltage value. In the adjustment after fix or exchange of a PW board, this voltage value is used as reference. You can get it from the vendor's web site on the Internet

1. Getting the characteristic voltage value of the PDP unit
1.1 Access the following address by the Web browser of vour PC http://203.126.119.92/necpd/
1.2 After [NEC-ITLS] screen is displayed, click "Click here to log on to NPD" (Fig. 1)
1.3 Type the following user name and password into the dialog box and click "Enter" button. (Fig. 2) Username: JVCJPN01 Password: ivckoseki (lower-case)
1.4 After [WELCOME TO NEC-ITLS] is displayed (Fig. 3). click the "Voltage" icon in the "Enguiry" holder on the upper left part of the window. (Fig. 4)
1.5 After IVOI TAGE ENQUIRY] is displayed (Fig. 5), enter the panel ID number, which is shown on the panel (refer to page 2), into the dialog box and click "GO".
1.6 Then, the characteristic voltage value will be displayed (Fig. 6)

Fig. 1 ∨ 🔁 移動 NEC-ITLS Enter Clear ページが表示されました 🕲 インターネット .----. NEC-ITLS . WELCOME TO NEC-ITLS NEC Menu Please select from the menu options on the left navigation NFC MPD-TTLS - Micr ファイル(圧) 編集(圧) 表示(型) お気に入り(型) アドレス(1) (4) http://203.126.110.02/necned/LoginPro NEC Menu : JVCJPN01 " 🖹 Yoltago - 🗎 Exit

Page 9

■ ADJUSTMENTS

ltem	Measuring instrument	Test point	Adjustment part	Description
Vsw VOLTAGE ADJUSTMENT	DC voltmeter	CN102 -pin 10 GND [COMMON PWB]	VR401 [COMMON PWB]	Measur e the voltag e betwee n the pin 10 of the connector [CN102] and GND on the COMMON PWB. Adjust the voltag e same as the referenc e data of Vsw shown in web site by VR401. **The adjustment accuracy is within ±0.5V.

Vbw / Vp+ VOLTAGE ADJUSTMENT	DC voltmeter	CN4 -pin 3(Vbw) -pin 8 (Vp+) GND [SCAN PWB]	VR1 (Vbw) VR2 (Vp+) [SCAN PWB]	Measure the voltage between the pin 3 of th e connecto r [CN4 ] and GN D on the SCAN PWB. Adjust the voltage same as the reference data of Vbw shown in web site by VR1. The adjustment accuracy is within ±0.5V. Measure the voltage between the pin 8 of CN4 and GND on the SCAN PWB. Adjust the voltage same as the reference data of Vp+ shown in web site by VR2. The adjustment accuracy is within ±1.5V.
The adjustment accuracy is within ±1.5V. *The adjustment accuracy is within ±1.5V.

Page 10

■PARTS LIST

٨	Ref No.	Parts No.	Parts name	Description
⚠	1	NE-9S899512	SCAN PWB
⚠	2	NE-9S899514	COMMON PWB
⚠	3	NE-9S899518	SIGNAL RELAY PWB	(upper left)
⚠	4	NE-9S899520	SIGNAL RELAY PWB	(upper right)
⚠	5	NE-9S899519	SIGNAL RELAY PWB	(lower left)
⚠	6	NE-9S899521	SIGNAL RELAY PWB	(lower right)
⚠	7	NE-9S899516	RECOVERY RELAY PWB
⚠	8	NE-9S899517	POWER RELAY PWB
⚠	9	NE-9S899590	DIGITAL PWB

NOTE : (1) In case of version with (F) as shown below, exchanging both SCAN

PWB and COMMON PWB at once is required. Version is indicated by the seal stuck on each PW board.

SCAN PWB : Ver.02G(F), 02J(F), 03B(F), 03D(F) COMMON PWB : Ver.02H(F), 02K(F), 03B(F), 03D(F)

NOTES AT THE TIME OF PW BOARD EXCHANGE

It will become the cause of failure if dust adheres to the inside of a connector, or a flat wire and a point-of-contact part.

When the PW board is exchanged, be careful of the dust and dirt of the inside of a connector, or a flat wire and a point-of-contact part enough.

Page 11

Page 12

Victor Company of Japan, Limited AV & MULTIMEDIA COMPANY VIDEO DISPLAY CATEG ORY 12, 3-chome, Moriya-cho, kanagawa-ku, Yokohama, kanagawa-prefecture, 221-8528, Japan

Page 13

JVC SCHEMATIC DIAGRAMS

PLASMA DISPLAY MONITOR

CD-ROM No.SML200012

Page 14

[COMB PWB PATTERN]

[INTERFACE PWB PATTERN]

NV-PD4200 / NV-PD4200/A STANDARD CIRCUIT DIAGRAM

■ NOTE ON USING CIRCUIT DIAGRAMS

1. SAFETY

The components identified by the ▲ symbol and shading are critical for safety. For continued safety replace safety critical components only with manufactures recommended parts.

2.SPECIFIED VOLTAGE AND WAVEFORM VALUES

The voltage and waveform values have been measured under the following conditions
(1)Input signal	:Colour bar signal
(2)Setting positions of each knob/button and
variable resistor	:Original setting position
	when shipped
(3)Internal resistance of tester	:DC 20k Ω /V
(4)Oscilloscope sweeping time	:H ⇒ 20µS/div
	:V ⇒ 5mS/div
	:Others ⇒ Sweeping time is
	specified
(5)Voltage values	:All DC voltage values
* Since the voltage values of sign	nal circuit vary to some extent
according to adjustments, use	them as reference values.

3.INDICATION OF PARTS SYMBOL [EXAMPLE]

●In the PW board :R1209→R209

4.INDICATIONS ON THE CIRCUIT DIAGRAM (1)Resistors


Resistance value
No unit	:[Ω]
К	:[KΩ]
М	:[M Ω ]
Rated allowable pow	ver
No indication	:1/10[W]
Others	:As specified
Туре
No indication	:Carbon resistor
OMR	:Oxide metal film resistor
MFR	:Metal film resistor
MPR	:Metal plate resistor
UNFR	:Uninflammble resistor
FR	:Fusible resistor
Composition resistor	1/2 [W] is specified as 1/2S or Comp.
)Capacitors
Capacitance value
1 or higher	:[pF]
less than 1	:[µF]
Withstand voltage
No indication	:DC50[V]
AC indicated	:AC withstand voltage [V]
Others	:DC withstand voltage [V]

AC indicated .AC withstand voltage [V] Others :DC withstand voltage [V] *Electrolytic Capacitors 47/50[Example]:Capacitance value [uE]/withstand voltage[V]

MPP ·Metalized polypropylene capacitor MF :Metalized film capacitor TF RF :Bipolar electrolytic capacitor TAN :Tantalum capacitor (3)Coils No unit :[µH] Others (4)Power Supply ·B2(12\/) ·0\ *Respective voltage values are indicated (5)Test point :Test point :Only test point display (6)Connecting meth :Wrapping or soldering

:Ceramic capacitor

:Metalized mylar capacitor

:Polypropylene capacitor

:Mylar capacitor

(7)Ground symbol

Type

No indication

⊥ :LIVE side ground
:ISOLATED(NEUTRAL) side ground

:Receptacle

EARTH ground
:DIGITAL ground

5.NOTE FOR REPAIRING SERVICE

This model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : (⊥) side GND and the ISOLATED(NEUTRAL) : (↓) side GND. Therefore, care must be taken for the following points.

(1)Do not touch the LIVE side GND or the LIVE side GND and the ISOLATED(NEUTRAL) side GND simultaneously. If the above

caution is not respected, an electric shock may be caused. Therefore, make sure that the power cord is surely removed from the receptacle when, for example, the chassis is pulled out.

(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL) side GND or never measure with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND and ISOLATED(NEUTRAL) side GND at the same time. If the above precaution is not respected, a fuse or any parts will be broken.

Since the circuit diagram is a standard one, the circuit and circuit constants may be subject to change for improvement without any notice.

Page 15


2	_/
······································	-4

CIRCUIT DIAGRAMS

٠	FILTER PWB CIRCUIT DIAGRAM ·
٠	TERMINAL PWB CIRCUIT DIAGRAM······ 2-9
٠	AV PWB CIRCUIT DIAGRAMS ······ 2-11
٠	COMB PWB CIRCUIT DIAGRAM ······ 2-15
٠	AUDIO PWB CIRCUIT DIAGRAM ······ 2-17
٠	DIGITAL PWB CIRCUIT DIAGRAMS ······ 2-19
٠	REMOTE PWB CIRCUIT DIAGRAM ······ 2-33
٠	INTERFACE PWB CIRCUIT DIAGRAM ·
٠	SENSOR PWB CIRCUIT DIAGRAM ······ 2-37
٠	CONTROL PWB CIRCUIT DIAGRAM ······ 2-37

PATTERN DIAGRAMS

٠	SENSOR PWB PATTERN	[ FX-7008A ] ·
٠	CONTROL PWB PATTERN	[ FX-4064A ] ·
٠	DIGITAL PWB PATTERN	[FX-1131A] ····· 2-39
٠	AV PWB PATTERN	[FX-8011A] ····· 2-43
٠	AUDIO PWB PATTERN	[ FX-8013A ] ····· 2-45
٠	REMOTE PWB PATTERN	[ FX-8014A ] ·
٠	TERMINAL PWB PATTERN	[ FX-6065A ] ·
٠	FILTER PWB PATTERN	[ FX-9063A ] ·
٠	COMB PWB PATTERN	[ FX-5020A ] ····· 2-48
٠	INTERFACE PWB PATTERN	[ FX-7009A ] ····· 2-48

[TERMINAL PWB PATTERN]

[FILTER PWB PATTERN]

Page 16

BLOCK DIAGRAM (ANALOG)

Page 17

NV-PD4200 NV-PD4200

BLOCK DIAGRAM (DIGITAL)

Page 18

NV-PD4200

2-7

Page 19

NV-PD4200

Page 20

Page 21

2-13

2-14

No.51732

No 51732

NV-PD4200 NV-PD4200

Page 22

NV-PD4200

No 51732

2-15 2-16

Page 23

No 51732

No.51732

Page 24

No 51732

Page 25

Page 26

NV-PD4200

Page 27

Page 28

Page 29

No.51732

Page 30

Page 31

NV-PD4200 NV-PD4200

IREMOTE PWB CIRCUIT DIAGRAMI

Page 32

NV-PD4200

Page 33

ISENSOR PWB CIRCUIT DIAGRAMI

ICONTROL PWB CIRCUIT DIAGRAMI

NV-PD4200

PATTERN DIAGRAMS

[SENSOR PWB PATTERN]

ICONTROL PWB PATTERNI

2-38

Page 34

2-40

Page 35

No.51732

Page 36

NV-PD4200

Page 37

Page 38

[AUDIO PWB PATTERN] (side B)

0500

Page 39

JVC SERVICE MANUAL

42"PLASMA DISPLAY MONITOR

NV-PD4200

BASIC CHASSIS
P1

Since some details of the GD-V4200PZW/GD-V4200PZW-G service manual (No.51566, Sep. 1999) were changed, we are informing you of these changes and of the new descriptions.

1. OUTLINE OF CHANGES

PDP PANEL CHANGE.
RS 232C TERMINAL DELETE.

2.DIFFERENCE OF PARTS LIST

CONTENTS / USING P.W. BOARD (P3-2) / PRINTED WIRING BOARD PARTS LIST (P3-7)

PARTS NO.
GD-V4200PZW NV-PD4200		PARTS NAME	DESCRIPTION
FX-1117A FX-1131A		DIGITAL P.W.BOARD ASS'Y

EXPLODED VIEW PARTS LIST (P3-3)

*	REF	PAF	RTS NO.		DESCRIPTION
2!3	NO.	GD-V4200PZW	NV-PD4200	PARISINAME	DESCRIPTION
⚠	2	QLE0004-001	QLE0004-003	PDP PANEL
⚠	14	LC20453-001A	LC20453-007A	ROLL R LABEL
	23	LC31038-001A	LC31038-005A	FCC LABEL
	25	LC20365-001C	LC20619-001A	INLET PANEL
	27	QNB0036-001		RETAINER ×2	DELETION
	39			DIGITAL P.W.BOARD ASS'Y	FX-1117A
					Ļ
					FX-1131A

Page 40

PACKING PARTS LIST (P3-16)

	RFF	REE PARTS NO.
⚠	NO.	GD-V4200PZW	NV-PD4200	PARTS NAME	DESCRIPTION
	1	LC20255-001B	LC20255-004A	TOP CARTON
⚠	15	LCT0318-001A	LCT0814-001A	INST BOOK
			CEAA001-001	BNC-RCA CONNECTOR	×5
			QPA01001505	POLY BAG	for CONNECTOR

PRINTED WIRING BOARD PARTS LIST

DIGITAL P.W.BOARD ASS'Y (P3-7)

_	SYMBOL	PAR	RTS NO.		DECODIDITION
∕∆	NO.	FX-1117A	FX-1131A	PARTS NAME	DESCRIPTION
	R1505	NRSA63J-472X		MG R	DELETION
	R1593-4		NRSA63J-101X	MG R	ADDITION
	Q1101	2SC2778/C/-X	2SC2412K/QR/-X	SI.TRANSISTOR
	Q1104	2SC2778/C/-X	2SC2412K/QR/-X	SI.TRANSISTOR
	Q1107	2SC2778/C/-X	2SC2412K/QR/-X	SI.TRANSISTOR
	Q1111-13	2SC2778/C/-X	2SC2412K/QR/-X	SI.TRANSISTOR
	Q1115	2SC2778/C/-X	2SC2412K/QR/-X	SI.TRANSISTOR
	Q1117	2SC2778/C/-X	2SC2412K/QR/-X	SI.TRANSISTOR
	IC1502	EPC1PC8-GDV4200	EPC1PC8-4200PCE	I.C.	SERVICE
	IC1601	MB90F553APF-P99	MB90F553APF-P9A	I.C.(MICRO-COMP)	SERVICE
	IC1602	AT24C32-GDV4200	AT24C32-4200PCE	I.C.(EP-ROM)	SERVICE

JVC GD-V4200PCE, GD-V4200PCE-G, GD-V4200PZW, GD-V4200PZW-G, GD-V4200PZW-GA Service manual & schematics

JVG SERVICE MANUAL

42" PLASMA DISPLAY MONITOR

NV-PD4200

TABLE OF CONTENTS

NOTES AT THE TIME OF PW BOARD EXCHANGE -

■CONFIRMING MODEL NAME, SERIAL NUMBER, ID NUMBER AND CODE NUMBER

MAIN PARTS LOCATION

■INSPECTION OF COMPONENTS ON THE PW BOARD

1. INSPECTION OF FUSES

2. INSPECTION OF ALARM LINES

3. INSPECTION OF DATA ICS

4. INSPECTION OF POWER ICS

5. INSPECTION OF SCAN IC DRIVERS

DISASSEMBLY PROCEDURE

■ CONFIRMING REFERENCE VOI TAGE

■ ADJUSTMENTS

■PARTS LIST

NOTES AT THE TIME OF PW BOARD EXCHANGE

JVC SCHEMATIC DIAGRAMS

PLASMA DISPLAY MONITOR

[COMB PWB PATTERN]

[INTERFACE PWB PATTERN]

NV-PD4200 / NV-PD4200/A STANDARD CIRCUIT DIAGRAM

■ NOTE ON USING CIRCUIT DIAGRAMS

1. SAFETY

2.SPECIFIED VOLTAGE AND WAVEFORM VALUES

3.INDICATION OF PARTS SYMBOL [EXAMPLE]

4.INDICATIONS ON THE CIRCUIT DIAGRAM (1)Resistors

(7)Ground symbol

5.NOTE FOR REPAIRING SERVICE

CONTENTS

CIRCUIT DIAGRAMS

PATTERN DIAGRAMS

BLOCK DIAGRAM (ANALOG)

BLOCK DIAGRAM (DIGITAL)

ISENSOR PWB CIRCUIT DIAGRAMI

PATTERN DIAGRAMS

JVC SERVICE MANUAL

42"PLASMA DISPLAY MONITOR

NV-PD4200

1. OUTLINE OF CHANGES

2.DIFFERENCE OF PARTS LIST

EXPLODED VIEW PARTS LIST (P3-3)

PACKING PARTS LIST (P3-16)

PRINTED WIRING BOARD PARTS LIST

DIGITAL P.W.BOARD ASS'Y (P3-7)