JVC DT-X71H, DT-X71C, DT-X71F User Manual

Model:
DT-X71F
DT-X71H
DT-X71C
Please read this User Manual throughout before using.
7" Portable On-camera LCD Monitor
User Manual
Preface
Congratulations on your purchase of this product. Please read this user manual carefully.
1 All internal technologies of this product are protected, including device, software and trademark.
Reproduction in whole or in part without written permission is prohibited.
2 All brands and trademarks are protected and other relative trademarks in this user manual are the
properties of their respective owners.
3 Due to constant effort of product development, Swit Electronics reserves the right to make changes and
improvements to the product described in this manual without prior notice.
4 This product is covered by 2 years conditional warranty, and misuse, abnormal handling, alterations or
modifications in design or construction will void this warranty. It is considered normal that the LCD bright dot defects are not to exceed three.
5 For any suggestions and requirements on this product, please contact us through phone, fax, Email, etc.
SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC.
Address: 4300 Stevens Creek Blvd. Suite 230 San Jose, CA 95129 Toll free: 1 866 986-SWIT(7948) Tel: 408 260-8258 Fax: 408 228-8438 Email: info@swit.us Website: www.swit.us
Maintenance
Monitor
1. Please keep the signal terminals and the cooling vent away from knife-edge, metal or liquid in order to avoid short-circuit and damage.
2. Please don't try to disassemble any parts of the monitor by yourself, which would probably damage the monitor and do harm to human body, and it will cause the invalidation of product warranty.
3. Please don't touch the screen with your fingers, which would probably deface the screen.
4. Please don't press the screen; the LCD is extremely exquisite and flimsy. The power Please use the provided power adapter or the battery recommended by the manufacturer in order to avoid damage.
Please never use the light connector (2-pin, female) in right front of camera handle to power the monitor; otherwise it will damage the circuit of the monitor.
Please disconnect the power cable or take off the battery under the following situations:
1. If you do not operate this monitor for a period of time;
2. If the power cable or power adaptor is damaged;
3. If you operate this monitor by the methods different from this User Manual, and cause unknown problems;
4. If the monitor housing is broken. Working Environment
1. Please don't lay this product on the unstable place.
2. Please don't lay this product in hot, cold or wet location. Cleaning
1. Please clean the screen with dry and downy cloth or special LCD cleanser.
2. Please do not press hard when cleaning the screen.
3. Please do not use water or other chemical cleanser to clean the screen. The chemical may damage the LCD.
4. For first time use, please tear off the factory LCD film. To protect the LCD screen, please post the LCD protection film offered in the package.
1. Features
DT -X71F
New high resolution 7 LCD Panel
16:9, 1024×600, 16.77 million colors, 900:1 contrast, and H160°/ V160°viewing angle.
Multiple inputs
2 HD/SD-SDI, 1 HDMI and 1 Composite input.
Loop through outputs
Each of the 2 input HD/SD-SDI has loop through output.
HDMI converted to SDI output
Supported HDMI formats: 480i / 576i / 720p (50,
59.94, 60) / 1080i (50, 59.94, 60) / 1080P (23.98 24, 25, 29.97, 30), and the output SDI will embed the audio (48KHz) from HDMI.
Waveform (Y, Cb, Cr, R, G, B) and full scale
There are totally 6 kinds of waveform display, available under both SDI and HDMI, to check the Luminance (Y), Blue-difference (Cb), Red-difference (Cr), Red (R), Green (G), Blue (B), and the Y, Cb, Cr can be simultaneously displayed, R, G, B can be simultaneously displayed, and each of the waveforms can be set to full scale display.
Vector scope
The displayed vector scope pattern is available under both SDI and HDMI, represents saturation as distance from the center of the circle, and hue as the angle, in standard position, around it.
Histogram (R, G, B)
The histogram is a bar graph that shows the distribution of luminance values in the picture. Therere R, G, B histograms that individually displayed simultaneously, available under both SDI and HDMI.
16-ch audio meter
Under HDSDI, it displays 16 channels audio bars, with mark, and under SDSDI or HDMI, it displays 2 channels audio bars with mark. The audio bar is green, and will turn yellow when audio exceeds
-20dB, and turn red when exceeds -10dB.
SDI timecode
Under SDI input, it can display the SMPTE timecode, which is used extensively for synchronization, and for logging and identifying material in recorded media.
Peaking focus assist (red/blue switch)
The Peaking focus assist function is to mark the sharpest edges of the image with red or blue color, for users to check if the subjects are focused.
Zebra stripes
Zebra Stripes are used to check if the image is over exposed or not by showing black and white lines on the monitor. It is considered over exposed when luminance value exceeds 90%.
False color
The false color is used to aid in the setting of camera exposure. Under false color mode, theres a false color key on the bottom of screen for reference. The over exposed subjects (above 101 IRE) on the monitor will display as RED, and the underexposed subjects will display as BLUE. For correct exposed subjects, it will display as green and pink.
Blue Only
Under the Blue Only Mode, only the blue pixels are used to generate the image, because hue and saturation can be adjusted quicker and more accurately.
DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor.
G-sensor auto flip
Enable the G-sensor auto flip, the image will rotate automatically when monitor is bottom up.
User definable function keys
There are 3 function keys on the monitor front panel, and users could define the functions to the keys to achieve shortcut.
User editable video title
User can edit a video title for the current camera, and the title will display on the top of screen.
Front and Rear 3-color TALLY light 2 TALLY lights design, to give live signals to people in front of the camera, as well as the camera operator behind.
DT -X71H
New high resolution 7 LCD Panel
16:9, 1024×600, 16.77 million colors, 900:1 contrast, and H160°/ V160°viewing angle.
Multiple inputs
2 HD/SD-SDI, 1 HDMI, 1 Composite input and L/R stereo audio.
Loop through outputs
1 HD/SD-SDI loop through output.
DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor.
Image Flip
Set image to rotate by 180°.
User definable function keys
There are 2 function keys on the monitor front panel, that permit users to define shortcuts for the various functions.
User editable video title
User can edit a video title for the current camera, and the title will display on the top of screen.
Front and Rear 3-color TALLY light 2 TALLY lights design, to give live signals to people in front of the camera, as well as the camera operator behind.
New high resolution 7 LCD Panel
16:9, 1024×600, 16.77 million colors, 900:1 contrast, and H160°/ V160°viewing angle.
Multiple inputs
1 HDMI, 1 Composite input and L/R stereo audio input.
Loop through outputs
1 Composite loop through output.
DSLR scale zoom in
The Canon DSLR outputs the CMOS sensor ratio HDMI and this zoom in mode can make the effective image scale full screen on the monitor.
Image Flip
Set image to rotate by 180°.
DT -X71C
User definable function keys
There are 2 function keys on the monitor front panel, and users could define the functions to the keys to achieve shortcut.
User editable video title
User can edit a video title for the current camera, and the title will display on the top of screen.
Front and Rear 3-color TALLY light 2 TALLY lights design, to give live signals to people in front of the camera, as well as the camera operator behind.
2. Panel Instruction
DT-X71F
Front view
PHONE: Earphone jackPOWER: Power on/off
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the POWER” again, the indicator is turned off and monitor is switched off. Disconnect with power cable or take off the battery if the monitor will not be used for a period of time.
IN: Input signal selection
Press IN and revolve the “OK” to select the input video signal.
F1: User definable function key 1 FOCUS: Peaking Focus Assist
Press “FOCUS once, it will display the current peaking on/off status. Press FOCUS again to switch on RED line focus assist, switch on BLUE line focus assist, and switch off in turn.
F.COLOR: False color
Press “F.COLOR once, it will display the current false color on/off status. Press F.COLOR again to switch on/off the false color mode.
DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
F2: User definable function key 2 F3: User definable function key 3 WAVEFORM: Display waveform
Press “WAVEFORM once, it will display the waveform menu as: Revolve OK to select a waveform display mode and turn it on. The selected waveform will display on the screen.
VECTOR: Display vector scope Press “VECTOR to switched on/off the Vector scope
MENU: Press to enter Menu OK: Select and Apply
Under menu system, revolve OK to adjust settings and press to apply; and out of menu system, directly revolve OK to adjust volume.
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Rear view
Input
Supported formats
CVBS
PAL / NTSC
HDMI 480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
SDI SMPTE-274M
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 23.98)
SMPTE-296M
720p (60 / 59.94 / 50)
SMPTE-125M
480i (59.94)
ITU-R BT.656
576i (50)
DC 12V IN: Connect with DC12V 4-pin XLR power adapter. TALLY Light: Red, Green and Yellow 3-color TALLY indicator Battery mount:
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.
HDSDI IN1/2: HD/SD-SDI input (BNC connector) HDSDI OUT: HD/SD-SDI loop through output (BNC connector) HDSDI LOOP1/2: HD/SD-SDI loop through output (BNC connector) VIDEO IN: Composite video input (BNC connector) TALLY controlling port (RJ45) HDMI: HDMI input
Input formats
DT-X71H
Front view
PHONE: Earphone jackPOWER: Power on/off
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the “POWER again, the indicator is turned off and monitor is switched off. Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of time.
VIDEO: Press to switch the input signal to Composite video HDMI: Press to switch the input signal to HDMI HD-SDI1: Press to switch the input signal to the first HD-SDI channel HD-SDI2: Press to switch the input signal to the second HD-SDI channel MENU: Press to enter Menu F1: User definable function key 1 F2: User definable function key 2 RATIO: 16:9 and 4:3 switch ZOOM: Picture Zoom-in
Press ZOOM to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.
DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
OK: Select and Apply
Under menu system, revolve OK to adjust settings and press to apply; and out of menu system, directly revolve OK to adjust volume.
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Rear view
Input
Supported formats
CVBS
PAL / NTSC
HDMI 480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
SDI SMPTE-274M
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 23.98)
SMPTE-296M
720p (60 / 59.94 / 50)
SMPTE-125M
480i (59.94)
ITU-R BT.656
576i (50)
DC 12V IN: Connect with DC12V 4-pin XLR power adapter. TALLY Light: Red, Green and Yellow 3-color TALLY indicator Battery mount:
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.
HDSDI IN1/2: HD/SD-SDI input (BNC connector) HDSDI OUT: HD/SD-SDI loop through output (BNC connector) VIDEO IN: Composite video input (BNC connector) AUDIO L/R: Stereo audio L/R input (RCA connector) TALLY controlling port HDMI: HDMI input
Input formats
DT -X71C
Front view
PHONE: Earphone jackPOWER: Power on/off
Connect with power cable or mount battery, press the “POWER” and the power indicator is turned on and after 10 seconds, the monitor will be switched on and get into normal working status. Press the POWER” again, the indicator is turned off and monitor is switched off. Remark: Disconnect with power cable or take off the battery if the monitor will not be used for a period of time.
VIDEO: Press to switch the input signal to Composite video HDMI: Press to switch the input signal to HDMI B/W: Black and White mode OVERSCAN: Overscan / Underscan switch MENU: Press to enter Menu F1: User definable function key 1 F2: User definable function key 2 RATIO: 16:9 and 4:3 switch ZOOM: Picture Zoom-in
Press ZOOM to switch ZOOM1: Canon DSLR scale zoom-in, and ZOOM2: pixel to pixel zoom-in.
DISPLAY: Display current settings
Press “Display” to display safety mark, title and the current input signal information
OK: Select and Apply
Under menu system, revolve OK to adjust settings and press to apply; and out of menu system, directly
revolve OK to adjust volume.
TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Rear view
Input
Supported formats
CVBS
PAL / NTSC
HDMI 480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
DC 12V IN: Connect with DC12V 4-pin XLR power adapter. Battery mount:
Connect with JVC battery BN-VF823 or SWIT battery BN-S8823 to power the monitor.
VIDEO OUT: Composite video loop through output (BNC connector) AUDIO L/R: Stereo audio L/R input (RCA connector) VIDEO IN: Composite video input (BNC connector) HDMI: HDMI inputTALLY controlling port TALLY Light: Red, Green and Yellow 3-color TALLY indicator
Input formats
3. Menu Operation
Press “MENU” and it will display menu system
Revolve “OK” to select an item. The selected item will be highlighted display. Press OK to enter the selected item.  Under menu system, press MENU to back to previous menu.  The menu will automatically save and quit if it remains idle.
4. Picture Settings Submenu
The Picture Settings Submenu includes:
CONTRAST: 0-100 value adjustment BRIGHTNESS: 0-100 value adjustment HUE: 0-100 value adjustment
(Only available under Composite input)
SATURATION: 0-100 value adjustment SHARPNESS: 0-100 value adjustment ⑹ PIC.MODE: User defined and preset picture
modes: standard, soft and vivid selection
5. System Configuration Submenu
The System Configuration Submenu includes:
RATIO: Select 16:9 or 4:3 to adjust the aspect ratio. SCAN: UNDERSCAN / OVERSCAN selection ⑶ ZOOM: OFF, ZOOM1 and ZOOM2 selection
ZOOM1: Canon DSLR scale zoom-in
ZOOM2: Pixel to Pixel zoom-in
MARKER: Select and set the safety mark
scale from 80%, 85%, 90% and 95%.
FLIP: Select YES to enable G-sensor auto
flip.
RESET: Revolve OK to RESET and press to
recover all to factory setting.
6. OSD Settings Submenu
The OSD Settings Submenu includes:
LANGUAGE: Menu language English / Chinese selection H-POSITION: Menu horizontal position (0-100) adjustment, real-time preview, default value: 50, center. V-POSITION: Menu vertical position (0-100) adjustment, real-time preview, default value: 50, center. DURATION: Menu timeout setting
Set a time (in seconds) in which the menu will automatically quit if remains idle. Default: 10 seconds; Range: 5 seconds to 60 seconds.
7. Title Settings Submenu
Revolve "OK" button to select the letters, and press "OK" to input. Select SPACE to input space and DEL to delete the left letter. Max 10 letters are supported. After setting, press "MENU", the system will save data to current user and quit menu. The menu will automatically save and quit if it remains idle.
8. Display Settings Submenu
The DISPLAY settings submenu is to select the items to be displayed on screen when DISPLAY button is pressed. Revolve "OK" to turn on/off the items: (1) INFO: Including Input format, aspect ratio,
underscan/overscan, zoom status (2) MARKER: Safety mark (3) TITLE: User edited title
9. FUNCTION KEY Settings Submenu
-------------------DT-X71F-------------------
-------------------DT-X71H-------------------
01-RATIO: Aspect ratio switch
01-RATIO: Aspect ratio switch
02-SCAN: Underscan / Overscan switch
02-SCAN: Underscan / Overscan switch
03-ZOOM: Picture Zoom-in
03-ZOOM: Picture Zoom-in
04-PIC. MODE: Preset picture mode switch
04-CLR.TEMP: Color-temperature switch
05-B/W: Color / Black & white switch
05-PIC MODE: Preset picture mode switch
06-BLUE ONLY: Blue only mode switch on/off
06-B/W: Color / Black & white switch
07-ZEBRA: Zebra over exposure switch on/off
07-REVERSE: Image flip
08-VECTOR: Vector scope switch on/off
-------------------DT-X71C-------------------
09-PATTERN: Internal colorbar switch on/off
01-RATIO: Aspect ratio switch
10-RGB HIST: R, G, B Histogram switch on/off
02-SCAN: Underscan / Overscan switch
11-TIMECODE: SDI timecode display switch on/off
03-ZOOM: Picture Zoom-in
12-F.COLOR: False color mode switch on/off
04-CLR.TEMP: Color-temperature switch
13-AUDIO BAR: Audio meter display switch on/off
05-PIC MODE: Preset picture mode switch
14-FOCUS: Peaking focus assist switch on/off, and
06-B/W: Color / Black & white switch
red/blue selection
07-REVERSE: Image flip
Terminal
1 2 3 4 5 6 7 8 Description
Y G GND R
The F KEY Settings Submenu is to define Function Keys on the front keyboard. The DT-X71F has 3 function keys: F1, F2 and F3; The DT-X71H and DT-X71C has 2 function
keys: F1 and F2.
The available function items of each model are:
10. TALLY Light Operation
There are front and rear TALLY lights on the monitor, which can display RED, GREEN and YELLOW signals. The TALLY light controlling port is the RJ45 socket at the rear panel, and terminal description is as follows:
The RED light is on when connecting the terminal “R” with “GND”, and goes out when disconnecting. The GREEN light is on when connecting the terminal “G” with “GND”, and goes out when disconnecting. The YELLOW light is on when connecting the terminal “Y” with “GND”, and goes out when disconnecting
11. Specifications
LCD Performance
Size
7.0 inches
Resolution
1024×RGB×600
Aspect ratio
16:9/4:3
Color system
NTSC/PAL
Brightness
400cd/m2
Contrast
900:1
Color
16.77 million colors
Viewing angle
H/V:160/160
Video Format
SDI * SMPTE-274M
1080i (60 / 59.94 / 50)
1080p (30 / 29.97 / 25 / 24 / 23.98)
SMPTE-296M
720p (60 / 59.94 / 50)
SMPTE-125M
480i (59.94)
ITU-R BT.656
576i (50)
HDMI 480I / 576I / 480P / 576P
1080i (60 / 59.94 / 50)
720p (60 / 59.94 / 50)
1080p (60 / 59.94 / 50 / 30 / 29.97 / 25 / 24 / 23.98)
General
Working voltage
DC12V, or Battery 6.5V-17V
Power consumption DT-X71F
15W
DT-X71H
8W
DT-X71C
6W
Working temperature
0℃~+40
Working humidity
10%90%
Storage temperature
-15℃~+60
Storage humidity
10%90%
Dimensions
192×139×47mm
Net weight
550g
1. Monitor
×1
2. User Manual
×1
3. Power adaptor
×1
4. Power cable
×1
5. Sun hood
×1
6. Screw ball head
×1
7. LCD protection film
×1
* DT-X71C doesnt support SDI input.
12. Packing List
This model is manufactured, warranted and supported by SWIT Electronics Co., Ltd. / SWIT Electronics USA, LLC, and distributed in North America by JVC Professional Video Products. To obtain service or for further information, please contact:
SWIT Electronics USA, LLC.
Address: 4300 Stevens Creek Blvd., Suite 230, San Jose, CA 95129 Toll free: 1 866 986-SWIT (7948) • Tel: 408 260-8258·Fax: 408 228-8438 Email: info@swit.us • Website: www.swit.us
Loading...