JVC DLA-HD250 Instruction Manual

0820TTH-AO-AO

© 2010 Victor Company of Japan, Limited

DLA-HD250

D-ILA PROJECTOR

PROYECTOR D-ILA

PROJECTEUR D-ILA

ENGLISH FRANÇAIS ESPAÑOL/CASTELLANO

For Customer use :

Enter below the serial No. which is
located on the side of the cabinet.
Retain this information for future
reference.

Model No. DLA-HD250

Serial No.

Instrucción para el cliente :

Introduzca a continuación el nº de
serie que aparece en la parte
inferior lateral de la caja. Conserve
esta información como referencia
para uso ulterior.

Modelo Nº DLA-HD250

Nº de serie

Pour utilisation par le client :

Entrer ci-dessous le N° de série qui
est situé sous le boîtier. Garder
cette information comme référence
pour le futur.

N° de modèle DLA-HD250

N° de série

INSTRUCTIONS

Getting Started

DLA-HD250

MANUEL D’INSTRUCTIONS

MANUAL DE INSTRUCCIONES

D-ILA PROJECTOR
PROJECTEUR D-ILA

PROYECTOR D-ILA

Preparation

DLA-HD250

Basic Operation

Settings

Troubleshooting

Others

1

or similar surface. It should not be placed in a built-in installation

-

To allow better heat dissipation, keep a clearance between
this unit and its surrounding as shown below. When this
unit is enclosed in a space of dimensions as shown below,
use an air-conditioner so that the internal and external
temperatures are the same.

-
the type of power supply to your home, consult your
product dealer or local power company.

- This product is equipped with a three-wire plug. This plug
will fit only into a grounded power outlet. If you are unable
to insert the plug into the outlet, contact your electrician to
install the proper outlet. Do not defeat the safety purpose
of the grounded plug.

- Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at doors,
plugs, receptacles, and the point where they exit from the
product.

- For added protection of this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage to
the product due to lightning and power line surges.

- Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as this can
result in a risk of fire or electric shock.

- Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.

- Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous
voltages and other hazards. Refer all service to qualified
service personnel.

-

Unplug this product from the wall outlet and refer service to

qualified service personnel under the following conditions:

a) When the power supply cord or plug is damaged.

b) If liquid has been spilled, or objects have fallen on the product.

c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the Operation Manual, as an improper adjustment
of controls may result in damage and will often require
extensive work by a qualified technician to restore the product

to normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance -

this indicates a need for service.

- When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.

-

Upon completion of any service or repairs to this product,
ask the service technician to perform safety checks to
determine that the product is in proper operating condition.

- The product should be placed more than one foot away
from heat sources such as radiators, heat registers,
stoves, and other products (including amplifiers) that
produce heat.

- When connecting other products such as VCR’s, and DVD
players, you should turn off the power

of this product for

protection against electric shock.

- Do not place combustibles behind the cooling fan. For
example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over heated.

- Do not look into the projection lens while the illumination
lamp is turned on. Exposure of your eyes to the strong
light can result in impaired eyesight.

- Do not look into the inside of this unit through vents
(ventilation holes), etc. Do not look at the illumination lamp
directly by opening the cabinet while the illumination lamp
is turned on. The illumination lamp also contains ultraviolet
rays and the light is so powerful that your eyesight can be
impaired.

- Do not drop, hit, or damage the light-source lamp (lamp
unit) in any way. It may cause the light-source lamp to
break and lead to injuries. Do not use a damaged light
source lamp. If the light-source lamp is broken, ask your
dealer to repair it. Fragments from a broken light-source
lamp may cause injuries.

- The light-source lamp used in this projector is a high
pressure mercury lamp. Be careful when disposing of the
light-source lamp. If anything is unclear, please consult
your dealer.

- Do not ceiling-mount the projector to a place which tends
to vibrate; otherwise, the attaching fixture of the projector
could be broken by the vibration, possibly causing it to fall
or overturn, which could lead to personal injury.

- Use only the accessory cord designed for this product to
prevent shock.

*DO NOT allow any unqualified person to install the

unit.

Be sure to ask your dealer to install the unit (e.g.
attaching it to the ceiling) since special technical
knowledge and skills are required for installation. If
installation is performed by an unqualified person, it
may cause personal injury or electrical shock.

power source indicated on the label. If you are not sure of

150 mm

and above

150 mm and above

300 mm
and above

200 mm
and above

Getting started

Safety Precautions

Safety Precautions

IMPORTANT INFORMATION

Th is p ro du ct h as a H ig h In te ns it y
Discharge (HID) lamp that contains
mercury.

Disposal of these materials may be
regulated in your community due to
environmental considerations . For
disposal or recycling information, please
contact your local authorities or for USA,
the Electronic Industries Alliance:
http://www.eiae.org.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING:

THIS APPARATUS MUST BE EARTHED.

CAUTION:

To reduce the risk of electric shock, do not remove cover.
Refer servicing to qualified service personnel.

This projector is equipped with a 3-blade grounding
type plug to satisfy FCC rule. If you are unable to insert
the plug into the outlet, contact your electrician.

FCC INFORMATION (U.S.A. only)

CAUTION:

Changes or modification not approved by JVC could
void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply
with the limits for Class B digital devices, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provi d e r ea s on ab le pr ot ec t io n a ga in st ha rm fu l
interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is encourage
to try to correct the interference by one or more of the
following measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and

receiver.

●Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

●Consult the dealer or an experienced radio/TV technician

for help.

MACHINE NOISE INFORMATION (Germany only)

Changes Machine Noise Information Ordinance 3. GSGV,
January 18, 1991: The sound pressure level at the operator
position is equal or less than 19 dB (A) according to
ISO 7779.

About the installation place

Do not install the projector in a place that cannot support
its weight securely.

If the installation place is not sturdy enough, the projector
could fall or overturn, possibly causing personal injury.

IMPORTANT SAFEGUARDS

Electrical energy can perform many useful functions. This
unit has been engineered and manufactured to assure your
personal safety. But IMPROPER USE CAN RESULT IN
POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In
order not to defeat the safeguards incorporated into this
product, observe the following basic rules for its installation,
use and service. Please read these Important Safeguards
carefully before use.

- All the safety and operating instructions should be read
before the product is operated.

- The safety and operating instructions should be retained
for future reference.

- All warnings on the product and in the operating instructions
should be adhered to.

- All operating instructions should be followed.

- Place the projector near a wall outlet where the plug can
be easily unplugged.

- Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.

- Do not use attachments not recommended by the product
manufacturer as they may be hazardous.

- Do not use this product near water. Do not use immediately
after moving from a low temperature to high temperature,
as this causes condensation, which may result in fire,
electric shock, or other hazards.

- Do not place this product on an unstable cart, stand, or
table. The product may fall, causing serious injury to a
child or adult, and serious damage to the product. The
product should be mounted according to the manufacturer’s
instructions, and should use a mount recommended by
the manufacturer.

- When the product is used on a cart, care
should be taken to avoid quick stops,
excessive force, and uneven surfaces
which may cause the product and cart to
overturn, damaging equipment or causing
possible injury to the operator.

- Slots and openings in the cabinet are
provided for ventilation. These ensure reliable operation of
the product and protect it from overheating. These openings
must not be blocked or covered. (The openings should
never be blocked by placing the product on bed, sofa, rug,

such as a bookcase or rack unless proper ventilation is
provided and the manufacturer’s instructions have been
adhered to.)

PORTABLE CART WARNING
(symbol provided by RETAC)

S3126A

2

ENGLISH

Getting Started

-

To allow better heat dissipation, keep a clearance between
this unit and its surrounding as shown below. When this
unit is enclosed in a space of dimensions as shown below,
use an air-conditioner so that the internal and external
temperatures are the same.

150 mm and above

300 mm
and above

150 mm

and above

200 mm
and above

power source indicated on the label. If you are not sure of

­the type of power supply to your home, consult your
product dealer or local power company.

- This product is equipped with a three-wire plug. This plug
will fit only into a grounded power outlet. If you are unable
to insert the plug into the outlet, contact your electrician to
install the proper outlet. Do not defeat the safety purpose
of the grounded plug.

- Power-supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or
against them. Pay particular attention to cords at doors,
plugs, receptacles, and the point where they exit from the
product.

- For added protection of this product during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage to
the product due to lightning and power line surges.

- Do not overload wall outlets, extension cords, or
convenience receptacles on other equipment as this can
result in a risk of fire or electric shock.

- Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or
short out parts that could result in a fire or electric shock.
Never spill liquid of any kind on the product.

- Do not attempt to service this product yourself as opening
or removing covers may expose you to dangerous
voltages and other hazards. Refer all service to qualified
service personnel.

-

Unplug this product from the wall outlet and refer service to

qualified service personnel under the following conditions:

a) When the power supply cord or plug is damaged.

b) If liquid has been spilled, or objects have fallen on the product.

c) If the product has been exposed to rain or water.
d) If the product does not operate normally by following the

operating instructions. Adjust only those controls that are
covered by the Operation Manual, as an improper adjustment
of controls may result in damage and will often require
extensive work by a qualified technician to restore the product

to normal operation.
e) If the product has been dropped or damaged in any way.
f) When the product exhibits a distinct change in performance -

this indicates a need for service.

- When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or with same characteristics as the original
part. Unauthorized substitutions may result in fire, electric
shock, or other hazards.

Upon completion of any service or repairs to this product,

­ask the service technician to perform safety checks to
determine that the product is in proper operating condition.

- The product should be placed more than one foot away
from heat sources such as radiators, heat registers,
stoves, and other products (including amplifiers) that
produce heat.

- When connecting other products such as VCR’s, and DVD
players, you should turn off the power
protection against electric shock.

- Do not place combustibles behind the cooling fan. For
example, cloth, paper, matches, aerosol cans or gas
lighters that present special hazards when over heated.

- Do not look into the projection lens while the illumination
lamp is turned on. Exposure of your eyes to the strong
light can result in impaired eyesight.

- Do not look into the inside of this unit through vents
(ventilation holes), etc. Do not look at the illumination lamp
directly by opening the cabinet while the illumination lamp
is turned on. The illumination lamp also contains ultraviolet
rays and the light is so powerful that your eyesight can be
impaired.

- Do not drop, hit, or damage the light-source lamp (lamp
unit) in any way. It may cause the light-source lamp to
break and lead to injuries. Do not use a damaged light
source lamp. If the light-source lamp is broken, ask your
dealer to repair it. Fragments from a broken light-source
lamp may cause injuries.

- The light-source lamp used in this projector is a high
pressure mercury lamp. Be careful when disposing of the
light-source lamp. If anything is unclear, please consult
your dealer.

- Do not ceiling-mount the projector to a place which tends
to vibrate; otherwise, the attaching fixture of the projector
could be broken by the vibration, possibly causing it to fall
or overturn, which could lead to personal injury.

- Use only the accessory cord designed for this product to
prevent shock.

of this product for

*DO NOT allow any unqualified person to install the

unit.

Be sure to ask your dealer to install the unit (e.g.
attaching it to the ceiling) since special technical
knowledge and skills are required for installation. If
installation is performed by an unqualified person, it
may cause personal injury or electrical shock.

Preparation

Basic Operation

Settings

Troubleshooting

Others

3

1

Safety Precautions (Continued)

POWER CONNECTION

WARNING:
Do not cut off the main plug from this equipment.

If the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power
point, then obtain an appropriate safety approved
extension lead or adapter or consult your dealer.
If nonetheless the mains plug is cut off, dispose of the
plug immediately, to avoid a possible shock hazard by
inadvertent connection to the main supply. If a new main
plug has to be fitted, then follow the instruction given
below.

WARNING:
THIS APPARATUS MUST BE EARTHED.

For USA and Canada only
Use only the following power cord.

Power cord

The power supply voltage rating of this product is
AC110V – AC240V. Use only the power cord designated
by our dealer to ensure Safety and EMC.

Ensure that the power cable used for the projector is the
correct type for the AC outlet in your country. Consult
your product dealer.

Power cord

For European continent countries

IMPORTANT (Europe only):

The wires in the mains lead on this product are colored
in accordance with the following cord:
Green-and-yellow : Earth
Blue : Neutral
Brown : Live
As these colors may not correspond with the colored
making identifying the terminals in your plug, proceed
as follows:
The wire which is colored green-and-yellow must be
connected to the terminal which is marked M with the
letter E or the safety earth or colored green or green­and-yellow.
The wire which is colored blue must be connected to
the terminal which is marked with the letter N or colored
black.
The wire which is colored brown must be connected to
the terminal which is marked with the letter L or colored
red.



Getting started

4

ENGLISH

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic
compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany

Getting Started

Preparation

Basic Operation

Settings

Troubleshooting

Others

5

1

Getting started

ENGLISH

Information for Users on Disposal of Old Equipment and Batteries

[European Union only]

These symbols indicate that equipment with these symbols should not be disposed of
as general household waste. If you want to dispose of the product or battery, please
consider the collection systems or facilities for appropriate recycling.

Notice: The sign Pb below the symbol for batteries indicates that this battery

contains lead.

Battery

Products

DEUTSCH

Benutzerinformationen zur Entsorgung alter Geräte und Batterien

[Nur Europäische Union]

Diese Symbole zeigen an, dass derartig gekennzeichnete Geräte nicht als normaler
Haushaltsabfall entsorgt werden dürfen. Wenden Sie sich zur Entsorgung des Produkts
oder der Batterie an die hierfür vorgesehenen Sammelstellen oder Einrichtungen, damit
eine fachgerechte Wiederverwertung möglich ist.

Batterie

Hinweis: Das Zeichen Pb unterhalb des Batteriesymbols gibt an, dass diese Batterie

Blei enthält.

Produkte

FRANÇAIS

Informations relatives à l’élimination des appareils et des piles usagés, à l’intention des utilisateurs

[Union européenne seulement]

Si ces symboles figurent sur les produits, cela signifie qu’ils ne doivent pas être jetés
comme déchets ménagers. Si vous voulez jeter ce produit ou cette pile, veuillez
considérer le système de collection de déchets ou les centres de recyclage appropriés.

Notification: La marque Pb en dessous du symbole des piles indique que cette pile

contient du plomb.

Pile

Produits

NEDERLANDS

Informatie voor gebruikers over het verwijderen van oude apparatuur en batterijen

[Alleen Europese Unie]

Deze symbolen geven aan dat apparatuur met dit symbool niet mag worden
weggegooid als algemeen huishoudelijk afval. Als u het product of de batterij wilt
weggooien, kunt u inzamelsystemen of faciliteiten voor een geschikte recycling
gebruiken.

Batterij

Opmerking: Het teken Pb onder het batterijsymbool geeft aan dat deze batterij lood

bevat.

Producten

6

Información para los usuarios sobre la eliminación de baterías/pilas usadas

[Sólo Unión Europea]

Estos símbolos indican que el equipo con estos símbolos no debe desecharse con la
basura doméstica. Si desea desechar el producto o batería/pila, acuda a los sistemas
o centros de recogida para que los reciclen debidamente.

ENGLISH

Getting Started

ESPAÑOL / CASTELLANO

Atención: La indicación Pb debajo del símbolo de batería/pila indica que ésta contiene

Baterías/pilas

Productos

plomo.

Informazioni per gli utenti sullo smaltimento delle apparecchiature e batterie obsolete

[Solo per l’Unione Europea]

Questi simboli indicano che le apparecchiature a cui sono relativi non devono essere
smaltite tra i rifiuti domestici generici. Se si desidera smaltire questo prodotto o questa
batteria, prendere in considerazione i sistemi o le strutture di raccolta appropriati per il
riciclaggio corretto.

Batteria

Prodotti

Nota: Il simbolo Pb sotto il simbolo delle batterie indica che questa batteria contiene

piombo.

PORTUGUÊS

Informação para os utilizadores acerca da eliminação de equipamento usado e pilhas

[Apenas União Europeia]

Estes símbolos indicam que o equipamento com estes símbolos não deve ser eliminado
juntamente com o restante lixo doméstico. Se pretende eliminar o produto ou a pilha,
utilize os sistemas de recolha ou instalações para uma reciclagem apropriada.

ITALIANO

Preparation

Basic Operation

Settings

Aviso: O sinal Pb abaixo do símbolo para pilhas indica que esta pilha contém chumbo.

Pilha

Produtos

Πληροφορίες για την απόρριψη παλαιού εξοπλισμού και μπαταριών

[ Ευρωπαϊκή Ένωση μόνο ]

Αυτά τα σύμβολα υποδηλώνουν ότι ο εξοπλισμός που τα φέρει δεν θα πρέπει να
απορριφθεί ως κοινό οικιακό απόρριμμα . Εάν επιθυμείτε την απόρριψη αυτού του
προϊόντος ή αυτής της μπαταρίας , χρησιμοποιήστε το σύστημα περισυλλογής ή
εγκαταστάσεις για ανάλογη ανακύκλωση .

Μπαταρία

Προϊόντα

Σημείωση : Το σύμβολο Pb κάτω από το σύμβολο μπαταρίας υποδηλώνει ότι η

μπαταρία περιέχει μόλυβδο .

ΕΛΛΗΝΙΚΑ

Troubleshooting

Others

7

1

Getting started

DANSK

Brugerinformation om bortskaffelse af gammelt udstyr og batterier

[Kun EU]

Disse symboler angiver, at udstyr med disse symboler ikke må bortskaffes som
almindeligt husholdningsaffald. Hvis du ønsker at smide dette produkt eller batteri ud,
bedes du overveje at bruge indsamlingssystemet eller steder, hvor der kan ske korrekt
genbrug.

Batteri

Bemærk: Tegnet Pb under symbolet for batterierne angiver, at dette batteri indeholder

bly.

Produkter

Tietoja vanhojen laitteiden ja akkujen hävittämisestä

[Vain Euroopan unioni]

Nämä symbolit ilmaisevat, että symboleilla merkittyä laitetta ei tulisi hävittää tavallisen
kotitalousjätteen mukana. Jos haluat hävittää tuotteen tai sen akun, tee se hyödyntämällä
akkujen keräyspisteitä tai muita kierrätyspaikkoja.

Huomautus: Akkusymbolin alapuolella oleva Pb-merkintä tarkoittaa, että akku sisältää

lyijyä.

Akku

Tuotteet

Information för användare gällande bortskaffning av gammal utrustning och batterier

SUOMI

SVENSKA

[Endast den Europeiska unionen]

Dessa symboler indikerar att utrustning med dessa symboler inte ska hanteras som
vanligt hushållsavfall. Om du vill bortskaffa produkten eller batteriet ska du använda
uppsamlingssystem eller inrättningar för lämplig återvinning.

Observera! Märkningen Pb under symbolen för batterier indikerar att detta batteri

innehåller bly.

Batteri

Produkter

Opplysninger til brukere om kassering av gammelt utstyr og batterier

[Bare EU]

Disse symbolene viser at utstyr med dette symbolet, ikke skal kastes sammen med
vanlig husholdningsavfall. Hvis du vil kassere dette produktet eller batteriet, skal du
vurdere å bruke innsamlingssystemene eller andre muligheter for riktig gjenbruk.

Merk: Tegnet Pb under symbolet for batterier, viser at batteriet inneholder bly.

Batteri

Produkter

NORSK

8

ENGLISH

Сведения для пользователей по утилизации старого оборудования и батарей

[только для Европейского союза]

Данные символы указывают на то, что оборудование, на которое они нанесены,
не должны утилизироваться, как обычные бытовые отходы. При необходимости
утилизировать такое изделие или батарею обратитесь в специальный пункт
сбора для их надлежащей переработки.

Батарея

Уведомление: Надпись Pb под символом батарей указывает на то, что данная

батарея содержит свинец.

Изделия

Informace pro uživatele k likvidaci starého zařízení a baterií

[Pouze Evropská unie]

Tyto symboly označují, že produkty s těmito symboly se nesmí likvidovat jako běžný
odpad. Pokud chcete produkt nebo baterii zlikvidovat, využijte sběrný systém nebo
jiné zařízení, které zajistí řádnou recyklaci.

РУССКИЙ

ČESKY

Getting Started

Preparation

Basic Operation

Upozornění: Značka Pb pod symbolem pro baterie znamená, že tato baterie

obsahuje olovo.

Baterie

Produkty

Informacje dla użytkowników dotyczące pozbywania się zużytego sprzętu i baterii

[Tylko kraje Unii Europejskiej]

Te symbole oznaczają, że sprzętu nie należy wyrzucać razem z odpadami
gospodarczymi. Jeśli trzeba pozbyć się tego produktu lub ba terii, proszę skorzystać
z systemu odbioru lub urządzeń do zbiórki odpadów elektronicznych, w celu
odpowiedniego ponownego ich przetworzenia.

Bateria

Uwaga: Oznaczenie Pb, znajdujące się pod symbolem baterii wskazuje, że ta bateria

zawiera ołów.

Produkty

Felhasználói információ az elhasznált berendezések és akkumulátorok elhelyezéséről

POLSKI

MAGYAR

Settings

Troubleshooting

Termékek

Akkumulátor

[Csak az Európai Unióban]

Ez a szimbólum azt jelzi, hogy a berendezés nem helyezhető az általános háztartási
hulladék közé. Ha meg szeretne szabadulni a terméktől vagy az akkumulátortól, akkor
legyen tekintettel az gyűjtő rendszerre vagy intézményekre a megfelelő hasznosítás
érdekében.

Others

Megjegyzés: Az alábbi Pb szimbólum - ha az akkumulátoron megtalálható - azt jelzi,

hogy az akkumulátor ólmot tartalmaz.

9

Main Features

Supports Multiple Digital Devices

●

Comes with 2 independent HDMI terminals that allows digital

transmission of high denition signals. (

P18

)

Beautiful Images on Big Screen

●

Enjoy smooth and high resolution video images with

no visible grid, brought about by full high denition
resolution of 1920 x 1080 pixels. (

P24

)

Perfect for Any Location

●

Comes with an 80% vertical and 34% horizontal lens

shift function. (

P22

)

1

Getting started

Contents

Getting started

Safety Precautions.............................................2

Main Features...................................................10

Contents...........................................................12

How to Read this Manual/Accessories/

Optional Accessories.......................................13

About this Manual................................................13

Check the Accessories.......................................13

Optional Accessories..........................................13

Controls and features.............................................14

How to Use the Remote control ......................17

Loading Batteries..................................................17

Effective Range of Remote Control Unit...........17

Settings

Setting Menu...................................................28

Procedures for Menu Operation......................28

Setting Menu......................................................29

Customizing Projected Images....................40

Changing the Initial Setting of Picture Mode .40

Registering User-dened Picture Mode...........41

Registering User-dened Picture Mode from the

Menu...................................................................41

Troubleshooting

Troubleshooting...............................................42

What to Do When these Messages

Preparation

Selecting Connecting Devices....................18

Connecting......................................................19

Connecting via Video Cable and S-Video

Cable................................................................19

Connecting via Component Video Cable........19

Connecting via HDMI Cable..............................20

Connecting via HDMI-DVI Conversion Cable...20

Connecting via SCART-RCA Cable....................21

Connecting via RGB Video Cable......................21

Installing the Projector and Screen.................22

Set Angle..................................................................22

Shift Adjustment.....................................................22

Screen Size and Projection Distance...............23

Are Displayed.................................................44

About Warning Indicators

.............................

45

Actions to Be Taken for Warning Mode...........45

Replacing the Lamp........................................46

Procedure for Lamp Replacement.................46

Resetting Lamp Time.........................................48

Cleaning and Replacing the Filter.................49

Others

RS-232C Interface...........................................50

RS-232C Specications.......................................50

Command Format..............................................50

RS-232C Communication Examples................53

Copyright and Caution.................................54

About Trademarks and Copyright....................54

Basic Operation

Projecting Image..............................................24

Convenient Features during Projection...........26

Setting the Screen Size........................................26

Masking the Surrounding Area of an Image......26

12

　 Caution.................................................................54

Mounting this Unit..............................................55

Specications..............................................56

Dimensions..........................................................57

ENGLISH

Optional Accessories

About this Manual

Check the Accessories

How to Read this Manual/
Accessories/Optional Accessories

Getting Started

LENS.AP

TINT

CONT

ASPECT

C.TEMP

N.R

SHARP

HIDE

● Buttons on the remote control are described as [Button Name].

● Items on the menu are described as “Selection Item”.

INFO

GAMMA

COLOR

BRIGHT

TEST

STAGE

BACK

CINEMA2

DYNAMIC

MENU

CINEMA1

NATURAL

Buttons to be used are colored in a darker

shade.

This manual mainly describes the operating method using the remote control.

■

Conventions in this manual

Describes the limitations of the functions or usage.

Indicates good-to-know information.

Describes operational precautions.

P13 Indicates relevant pages for reference.

Preparation

Basic Operation

The power cord supplied varies depending on the destination.

Power Cord

Remote Control

AAA size Batteries

(for operation conrmation)

For European continent countries (2m)

For USA (2m)

Power Cord

● Instruction manual, warranty card and other printed material are also included.

Please check with your authorized dealer for details.

● Replacement Lamp: BHL5010-S (Lamp Unit)

● Replacement Filter (black in appearance): PB006560999 (Inner Filter)

Settings

Troubleshooting

Others

Replacement Filter (white in appearance): PB006575099 (Inner Filter)

13

1

Getting started

Controls and features

■

Front Side/Left Side

Do not place your fingers in the gap at the lens

●

during lens shift adjustment. This may cause injuries
if your ngers are caught in between the gap.

(

Do not let your ngers or other objects get caught in

●

between the lens cover while closing the cover. This
can cause injuries or malfunction.

■

Rear Side/Top Side/Right Side

P22

)

CAUTION

Exhaust Vent

Remote Sensor

P17

)

(

Lens Cover

Air Inlet

Lens Cover (opened)
(

P24

)

(closed)

14

To connect the power cord (

Lamp Cover (

)

P24

Remote Sensor (

)

P46

P17

)

WARNING

ENGLISH

Light on (Red): Warning mode

P45

)

(

Getting Started

Light on (Red):
Standby mode
Light on (Green):
During projection
Blinking (Green):

Image is temporarily hidden
(
Blinking (Red):
Cool Down mode
(

P25

P25

)

)

Left button

Down button

To display the menu

(

P28

LAMP

STANDBY/ON

INPUT

HIDE

OK

MENU

)

BACK

Light on/Blinking (Orange):

Lamp warning

)

(

P45

To turn on/off the power

To switch input (

To hide the image temporarily
(

Up button

Right button

To return to the previous menu

P24

P25

)

)

Preparation

Basic Operation

■

Bottom Surface

Air inlets/Filter (

Feet: The height (0 to 5 mm) can be adjusted by turning the foot.

Air inlets

)

P50

Manual button for lens cover:
Press and hold the button to open the lens cover.

Do not close lens cover when projecting. Otherwise

●

it will cause malfunction, heat and re.

CAUTION

Settings

Troubleshooting

Others

15

1

Getting started

Controls and features (continued)

■

Remote Control

To turn off the power

To control lens (

To display information (

Lens Aperture (
To set gamma (

To adjust color density (

To adjust hue (

To adjust brightness (

To display test pattern

To display/close the menu

STANDBY

ON

To turn on the power

)

P24

P39
P40
P40

P40
P40
P40

)
)
)

)
)
)

LENS

INFO

GAMMA

COLOR

BRIGHT

TEST

LENS.AP

TINT

CONT

INPUT

ASPECT

C.TEMP

N.R

SHARP

HIDE

To select input mode (

To set the screen size (

P24

P26

To adjust color temperature (

To adjust noise reduction (

To adjust sharpness (
To adjust contrast (

P40

P40

)

To hide the image temporarily (

)

P40

)

)

P40

)

)

P25

)

To select or conrm

P28

)

(

MENU

CINEMA1

BACK

CINEMA2

To return to the previous menu

NATURAL

USER1

STAGE DYNAMIC

USER3

USER2

LIGHT

RM-MH2GB

To switch picture mode (

P40

)

To illuminate buttons on the remote control
for 7 seconds

16

ENGLISH

Effective Range of Remote Control Unit

Loading Batteries

How to Use the Remote control

Getting Started

1

2 3

● If the remote control has to be brought closer to the projector to operate, it means that the batteries are wearing out.

When this happens, replace the batteries. Insert the batteries according to the + - marks.

● Be sure to insert the - end rst.

● If an error occurs when using the remote control, remove the batteries and wait for 5 minutes. Load the batteries again

and operate the remote control.

■ When directing the remote control

toward this unit

● When aiming the remote control towards the

remote sensor on this unit, ensure that the
distance to the sensor in front or at the rear of
this unit is within 7 m.

● If the remote control fails to work properly,

move closer to this unit.

This unit

30°

30°

20°
20°

Preparation

Basic Operation

Settings

■

When reecting off a screen

● Ensure that the total of distance A between

this unit and screen and distance B between
remote control and screen is within 7 m.

● As the efciency of signals reected from the

remote control unit differ with the type of
screen used, operable distance may decrease.

Screen

20°

A

20°

B

Remote control

30°

30°

Remote control

This unit

Troubleshooting

Others

17

2

Preparation

Selecting Connecting Devices

● Do not turn on the power until connection is complete.

● The connection procedures differ according to the device used. For details, refer to the instruction manual of the device to be

connected.

● For audio output, connect the device to an amplier.

● The images may not be displayed depending on the devices and cables to be connected.

Use an HDMI compliant cable (sold separately) with the HDMI logo.

● It may not be possible to connect to this unit depending on the dimension of the connector cover of the cables to be

connected.

DVD Recorder

To connect via HDMI terminal (

HDMI 1

HDMI 2

DVD Player

)

P20

To connect via component video terminals (

P19

)

To connect RS-232C terminal

(external control) (

VIDEO

Y

CB/PB

CR/PR

S-VIDEO

SYNC

RBG

RS-232C

P50

)

18

To connect via video terminal (

Notebook PC

P19

)

To connect via S-video terminal (

P19

)

VCR and camcorder

Connecting

Connecting via Component Video Cable

Connecting via Video Cable and S-Video Cable

ENGLISH

Getting Started

This unit

To video input termina

HDMI 2

HDMI 1

This unit

video cable

Video output

Preparation

(sold separately)

VCR and camcorder

l

Y

VIDEO

CB/PB

CR/PR

S-VIDEO

RBG

SYNC

To S-video input terminal

S-video cable

(sold separately)

S-video output

Basic Operation

Settings

VIDEO

CB/PB

Y

HDMI 1

HDMI 2

CR/PR

BG

SYNC

R

To component video input terminals

S-VIDEO

RS-232C

Component video cable

(sold separately)

●

Set “COMP.” in the setting menu to “Y Pb/Cb Pr/Cr”. ( P33 - 12 )

DVD player

Component video output
terminals

(red)

C

R/PR

C

(blue)

B/PB

Y (green)

Troubleshooting

Others

19

2

Connecting via HDMI Cable

Connecting via HDMI-DVI Conversion Cable

Connecting(Continued)

Preparation

This unit

This unit

HDMI 1

HDMI 2

Y

CB/PB

VIDEO

CR/PR

BG

R

SYNC

To HDMI 1 or HDMI 2 input terminal

HDMI cable (sold separately)

S-VIDEO

DVD recorder

HDMI output terminal

HDMI 1

HDMI 2

Y

CB/PB

VIDEO

CR/PR

S-VIDEO RS-232C

R

SYNC

BG

To HDMI 1 or HDMI 2 input terminal

HDMI-DVI conversion cable

(sold separately)

● If noise is produced, take PCs (including notepads) away from this unit.

20

Notebook PC

DVI output terminal

Connecting via SCART-RCA Cable

Connecting via RGB Video Cable

This unit

ENGLISH

Getting Started

Preparation

HDMI 1 HDMI 2

Y

G

VIDEO

CR/PR

CB/PB

B

S-VIDEO

SYNC

R

RS-232C

To RGB video and
sync signal input terminals

SCART-RCA cable

(sold separately)

● Set “COMP.” in the setting menu to “SCART”.( P33 -

This unit

12

DVD player for European market

Basic Operation

SCART terminal

)

Settings

HDMI 1 HDMI 2

Y

VIDEO

CR/PR

CB/PB

BG

S-VIDEO

SYNC

R

RS-232C

To RGB video input terminals

RGB video cable

(sold separately)

● Set “COMP.” in the setting menu to “RGB”.( P33 -

● For information on compatible input signals, see “Specications”. ( P56)

12

Troubleshooting

Device equipped with RGB output

RGB video output terminals

R(Red)

B(Blue)

G(Green)
(Includes sync signals)

)

Others

21

2

Set Angle

Shift Adjustment

Preparation

Installing the Projector and Screen

While installing, please place this unit and the screen perpendicular to each other. Failing to do so may

increase trapezoidal distortion. Please refer to “Keystone”. ( P36 -

● The angle range which can be set for this unit is ±10°.

24

)

10°

10°

● Malfunctions may occur if the angle is not set within the above-mentioned range.

10°

10°

Installing the projector and screen

1

■

Left/Right position

* 0% up/down position (center)

Approximately 34% (maximum) of

the projected image

Approximately 34% (maximum) of

■

Up/Down position

* 0% left/right position (center)

the projected image

■

Shifting range of projected image

22

Approximately 80% (maximum) of

the projected image

Approximately 80% (maximum) of

the projected image

80%

34%34%

镜头中心

80%

ENGLISH

Screen Size and Projection Distance

2

Adjust such that the projected image is in the center of the screen

Getting Started

Lens Control

1

3

4

LENS

LENS

Adjust the image position to the center of the screen by pressing

Focus

Select

Exit

MENU

Operate

Lens control

Shift

Back

Select
Operate

2

BACK

Back

BACK

LENS

(the up, down, left and right buttons).

● It may be necessary to set “Pixel Adjust” in the setting menu after adjusting the image position. ( P36 -

Lens Control

Zoom

Exit

MENU

22

Select
Operate

)

Back

BACK

Preparation

Basic Operation

Determine the distance from the lens to the screen to achieve your desired screen size.
This unit uses a 2.0x power zoom lens for projection.

■

Relationship Between Projection Screen Size and Projection Distance

Projection Screen Size

(Diagonal Length)

Aspect Ratio 16:9

60"

(Approx. 1.52m)

70"

(Approx. 1.78m)

80"

(Approx. 2.03m)

90"

(Approx. 2.29m)

100"

(Approx. 2.54m)

110"

(Approx. 2.79m)

120"

(Approx. 3.05m)

130"

(Approx. 3.30m)

Approximate Projection Distance

W(Wide) to T(Tele)

Approx. 1.78m to

Approx. 3.66m

Approx. 2.09m to Approx. 4.28m

Approx. 2.40m to

Approx. 2.70m to

Approx. 3.01m to

Approx. 3.31m to

Approx. 4.89m

Approx. 5.51m

Approx. 6.13m

Approx. 6.75m

Approx. 3.62m to Approx. 7.36m

Approx. 3.92m to

Approx. 7.98m

Projection Screen Size

(Diagonal Length)

Aspect Ratio 16:9

140"

(Approx. 3.56m)

150"

(Approx. 3.81m)

160"

(Approx. 4.06m)

170"

(Approx. 4.32m)

180"

(Approx. 4.57m)

190"

(Approx. 4.83m)

200"

(Approx. 5.08m)

Approximate Projection Distance

W(Wide) to T(Tele)

Approx. 4.23m to Approx. 8.60m

Approx. 4.53m to

Approx. 9.22m

Approx. 4.84m to Approx. 9.84m

Approx. 5.14m to Approx. 10.45m

Approx. 5.45m to Approx. 11.07m

Approx. 5.75m to Approx. 11.68m

Approx. 6.06m to

Approx. 12.30m

● The projection distances in the table are provided only as a guide. Use them as a reference during installation.

● To adjust the installation, use a projected image of aspect ratio 16:9.

Settings

Troubleshooting

Others

23

3

Basic Operation

Projecting Image

This section describes the basic operations to project input images on the screen.

Preparation

STANDBY

LENS

LENS.AP

INFO

GAMMA

COLOR

BRIGHT

CONT

TEST

MENU

CINEMA1

NATURAL

STAGE

USER1 USER2

TINT

LIGHT

ON

INPUT

ASPECT

C.TEMP

N.R

SHARP

HIDE

BACK

CINEMA2

DYNAMIC

USER3

1

Insert the power plug to the power

outlet

1

Connect to this unit

2

Connect to the power outlet

1

2

Turn on the power

ON

● You can also press the button on the unit to turn on the power.

(

3

Project the image

P15)

● The lens cover will be opened.

Power Cord

(Supplied)

STANDBY/ON

2

Light on (Green)

STANDBY/ON

Light on (Red)

WARNING

LAMP

ST ANDBY/ON

RM-MH2GB

1

Select input mode

2

4

screen

INPUT

● You can also select the input mode by pressing the

unit. (

Play back the selected device

Adjust the position of the projection

HDMI 1 HDMI 2 　 COMP． Video S-Video

P15)

● See “Installing the Projector and Screen” ( P22) and “Lens

Control” (

5

Adjust the image size (zoom) and the

P36 -

) for the adjustment method.

21

focus

1

Adjust the focus

LENS

Lens Control

Focus

Exit

MENU

Select
Operate

Back

BACK

Adjust accordingly by pressing

the up/down buttons

INPUT

button on the

24

Adjust the image size (zoom)

BACK

Back

Operate

Select

Exit

MENU

Zoom

Lens Control

2

LENS

ENGLISH

Getting Started

TIPS

You can hide the image temporarily

Every time the

●

will be switched among “Focus”, “Zoom” and “Shift”.

LENS

3

To end

BACK

Turn off the power

6

While a confirmation

screen is displayed

LENS

Focus Zoom

Adjust accordingly by

pressing the up/down

buttons

button is pressed, the adjustment item

Shift

You can hide the image temporarily.

HIDE

Green light blinks
when the image is

● Press the

image.

hidden.

button again to display

HIDE

● The power cannot be turned off when the

image is temporarily hidden.

MEMO

About Cool Down mode

Preparation

Basic Operation

Settings

Blinking (Red Lamp)

Cool Down mode

Light on (Red Lamp)

● When power off, the lens cover will be closed.

● The power cannot be turned off within approximately 90 seconds

after it has been turned on. Start operation only after 90 seconds
time.

● You can also press the button on the unit to turn off the

power. (

P15)

● Pull out the power plug when the unit will not be used for a

prolonged time.

● The Cool Down mode is a function to

cool down the lamp for approximately 60

seconds after projection is complete. This

function prevents the internal parts of the
unit from deformation or damage due to

overheating of the lamp. It also prevents

lamp blowout and premature shortening

of lamp life.

During Cool Down mode, the [STANDBY/

●

ON] indicator blinks in red.

● After the Cool Down mode is complete,

the unit automatically returns to standby

mode.

● Do not pull out the power plug during

Cool Down mode. This may shorten the
lamp life and cause a malfunction.

Troubleshooting

Others

25

3

Setting the Screen Size

Masking the Surrounding Area of an Image

Basic Operation

Convenient Features during Projection

You can change the screen size of the projected image or hide the surrounding area of an image for which
quality at the outer area has deteriorated.

STANDBY

LENS

INFO

GAMMA

COLOR

BRIGHT

TEST

MENU

CINEMA1

LENS.AP

TINT

CONT

ON

INPUT

ASPECT

C.TEMP

N.R

SHARP

HIDE

BACK

CINEMA2

The projected image can be set to a most appropriate screen size

(aspect ratio).

ASPECT

4:3 16:9 zoom

● The screen size can also be set from “Aspect(Video)” of the setting menu.

(

P34 -

14

)

● When PC signals are input, the “Aspect(Computer)” setting will be available

instead. (

■

Input Image and Projected Image by Different Screen Size

P34 -

Settings

Input Image

SDTV(4:3) Aspect Ratio:

)

15

4:3 16:9 Zoom

Same
Most appropriate
screen size

Screen Size

Aspect Ratio:
Landscape
Image is stretched
horizontally

Aspect Ratio:
Same
Top and bottom
of the image are
missing

NATURAL

USER1

STAGE

USER2

LIGHT

RM-MH2GB

DYNAMIC

USER3

SDTV(4:3)

Image recorded in

landscape (black

bands on top and
bottom) of DVD
software

Aspect Ratio:
Same
Small image is
projected

Aspect Ratio:
Landscape
Image is stretched
horizontally

Aspect Ratio:
Same
Most appropriate
screen size

● Depending on the input image, selecting “4:3” may result in a vertically

stretched image, while selecting “16:9” provides you with the most

appropriate screen size.

Images for which quality at the outer area has deteriorated can be projected by

masking (hiding) the surrounding area of the projected image.

1

Project the image

Image for which quality
at the outer area has

deteriorated.

26

Mask the image

Video/S-Video

COMP.

Aspect（Video）
Aspect（Computer)
V-stretch
Picture Position
Over scan

Film Mode

Exit

MENU

BACK

Back

Select

Operate

HDMI

16:9
Auto

Auto

Off

Off

Mask

Off

5%
Off

2.5%

Input Signal

2

1

Display the setting menu

MENU

Picture Adjust

Picture Mode

Contrast
Brightness
Color
Tint
Color Temp.
Gamma
Advanced

Lens Aperture

Exit

MENU

Select

ENGLISH

Getting Started

MEMO

● Masking is available only when high

Natural

0

0
0

0

6500K

Normal

2

Reset

Operate

Back

BACK

denition images are input.

Preparation

2

Select “Input Signal”

1

Select

3

Set a mask value

Select

1

“Mask”

Confirm

2

Confirm

2

Input Signal

HDMI
COMP.
Video/S-Video
Aspect（Video）
Aspect（Computer)
V-stretch
Picture Position
Over scan
Mask
Film Mode

Exit

MENU

Select

自动

Operate

Basic Operation

Settings

16:9
Auto

Off

Off

2.5%
5%

5%

Off

Auto

Back

BACK

Example:
When the “Mask” value is
changed from “Off”

To end

3

MENU

Troubleshooting

“5%”

Others

27

4

Procedures for Menu Operation

Settings

Setting Menu

Projected images can be adjusted to a desired view by changing the initial settings.

STANDBY

LENS

INFO

GAMMA

COLOR

BRIGHT

TEST

MENU

CINEMA1

NATURAL

USER1

LENS.AP

TINT

CONT

STAGE

USER2

ON

INPUT

ASPECT

C.TEMP

N.R

SHARP

HIDE

BACK

CINEMA2

DYNAMIC

USER3

Example:

When changing “Aspect(Video)” from “4:3” to “16:9”

1

Display the setting menu

Picture Adjust

Picture Mode

Contrast
Brightness

MENU

2

Select “Input Signal” “Aspect(Video)”

Select

1

Confirm

2

Color
Tint
Color Temp.
Gamma
Advanced
Lens Aperture

Exit

MENU

Input Signal

HDMI
COMP.
Video/S-Video

Video

Aspect（
Aspect（Computer)
V-stretch
Picture Position
Over scan
Mask
Film Mode

Exit

MENU

Select

Select

Natural

0

0
0

0

6500K

Normal

2

Reset

Operate

Back

BACK

Auto

Auto

Operate

4:3

4:3

16:9

Zoom

Off

Off
5%

Back

BACK

)

LIGHT

RM-MH2GB

3

Set to “16:9”

Select

1

4

To end

MENU

Confirm

2

Input Signal

HDMI
COMP.
Video/S-Video

Video

)

Aspect（
Aspect（Computer)
V-stretch
Picture Position
Over scan
Mask
Film Mode

Exit

MENU

Select

16:9

Auto

Auto

Operate

4:3

16:9

Zoom

Off

Off
5%

Back

BACK

28

Setting Menu

Item values shown in are factory settings.

● Items that can be congured differ according to the input signals.

ENGLISH

Getting Started

Picture Adjust

01

Picture Mode

Adjusts the pattern of the projected image.

Cinema 1, Cinema 2, Natural, Stage, Dynamic, User 1, User 2 and User 3.

02

Contrast

Adjusts the contrast of the projected image.

(Black) –50 to 50 (White)

03

Brightness

Adjusts the brightness of the projected image.

(Darken) –50 to 50 (Brighten)

04

Color

Adjusts the color density of the projected image.

(Lighten) –50 to 50 (Darken)

05

Tint

Adjusts the hue of the projected image.

(Red) –50 to 50 (Green)

● “Contrast”, “Brightness”, “Color” and “Tint” can also be congured from the remote control. ( P16)

Preparation

Basic Operation

Settings

Troubleshooting

Others

29

4

Settings

Setting Menu (Continued)

Picture Adjust > Color Temp.

06

Color Temp.

Sets the color temperature of the projected image.

5800K

6500K Select this to have a balanced image.

7500K

9300K

High Bright Select this to get the brightest image.

Custom 1

Custom 2

Custom 3

Select this to give a reddish tinge to the

image.

Select this to give a bluish tinge to the

image.

Select this to give a greater bluish tinge

than 7500K.

Gain

(Bright part)

Offset

(Dark part)

Gain

(Bright part)

Offset

(Dark part)

Gain

(Bright part)

Offset

(Dark part)

Red (Less red) –255 to 0 (More red)

Green (Less green) –255 to 0 (More green)

Blue (Less blue) –255 to 0 (More blue)

Red (Less red) –50 to 50 (More red)

Green (Less green) –50 to 50 (More green)

Blue (Less blue) –50 to 50 (More blue)

Red (Less red) –255 to 0 (More red)

Green (Less green) –255 to 0 (More green)

Blue (Less blue) –255 to 0 (More blue)

Red (Less red) –50 to 50 (More red)

Green (Less green) –50 to 50 (More green)

Blue (Less blue) –50 to 50 (More blue)

Red (Less red) –255 to 0 (More red)

Green (Less green) –255 to 0 (More green)

Blue (Less blue) –255 to 0 (More blue)

Red (Less red) –50 to 50 (More red)

Green (Less green) –50 to 50 (More green)

Blue (Less blue) –50 to 50 (More blue)

Only offset can be set.

● The red, green and blue colors can be adjusted and registered respectively.

● This setting can also be congured from the remote control. ( P16)

30

Picture Adjust > Gamma

07

Gamma

Sets the gradation characteristics of the projected image.

Normal

A Set gamma to “A”.
B Set gamma to “B”.
C Set gamma to “C”.

Custom 1
Custom 2
Custom 3

(Gamma Setup)

For normal circumstances, select this

setting.

Three different kinds of gamma can be set according to your preferences.

Correction

Value

The coefcient (1.8 to 2.6) of the gamma curve can be selected.

The gamma curve for the colors (Red, Green, Blue) can be adjusted

Gamma

Adjustment*

separately.

Adjusting “White” will adjust for all “Red, Green, Blue” values. The

gamma curve displays the value for "Green".

Copy Copy the adjusted gamma data.

Paste Paste the copied gamma data.

Reset

Return the gamma coefficients to the values 2.2 set by “Correction

Value”.

ENGLISH

Gamma adjustment cannot be performed,

and only copy is valid.

Getting Started

Preparation

Basic Operation

● “Normal” is suitable for normal circumstances but other settings can be selected according to your preferences.

● This setting can also be congured from the remote control. ( P16)

* “Gamma Adjustment”

Select the reference gamma curve coefcient (1.8 ～ 2.6) in “Correction Value”.

1

Select the color to be adjusted in the gamma adjustment screen.

2

Picture Adjust

>

Gamma

Normal

Correction Value

A

White

Red

B

Green

C

Blue

Costom1
Costom2

Copy

Costom3

Paste
Reset

Exit

MENU

Select

Adjust the gamma curve in the gamma curve adjustment screen.

3

Picture Adjust

>

Gamma

Normal

Correction Value

A

White

Red

B

Green

C

Blue

Costom1
Costom2

Copy

Costom3

Paste
Reset

Input: 10%
Output:100

Exit

MENU

Select

Select the point where the gradation (brightness)

is to be adjusted with the

1023

1023

512

Operate

512

0

Back
Operate

2.2

0

50

100(%)

Back

BACK

Picture Adjust

>

2.2

50

100(%)

Back

BACK

Gamma

Normal
A
B
C
Costom1
Costom2
Costom3

Exit

MENU

Correction Value

White

Red

Green

Blue

Copy
Paste

Reset

Input: 50%
Output: 580

Select

1023

512

0

Back
Operate

2.2

50

100(%)

Back

BACK

Adjust the gradation (brightness) with

the

/ buttons.

/ buttons.

Settings

Troubleshooting

To end

4

BACK

BACK

Save gamma data?

Yes

No

OK

● If gamma curve is adjusted repeatedly, calculation errors will be accumulated and the gamma curve may not be able to

revert back to its original form. In that case, select “Reset”.

Others

31

4

Settings

Setting Menu (Continued)

Picture Adjust

08

Advanced

Adjusts the contours of the image and detailed composition of the image.

Sharpness (Soft) 0 to 100 (Sharp) Adjusts the outline of image.

Sharpness

NR*

CTI*

09

Lens Aperture

Lens Aperture

10

Reset

Reset the setting.

Detail
Enhancement

RNR (Soft) 0 to 16 (Strong)

MNR (Soft) 0 to 16 (Strong)

BNR

(Soft) –50 to 50 (Strong) Emphasizes the details of image.

On Reduces block noise.
Off Input signal remains unchanged.

Off Input signal remains unchanged.

Low

High

1 Dark
2 Medium
3 Bright

Adjusts the intensity of removing

image noise.

Adjusts the intensity of removing

mosquito noise.

Reduces color smear.Middle

* In case of HD signals or PC signals, NR and CTI cannot be set.

● Abbreviations

NR: Noise Reduction
RNR: Random Noise Reduction
MNR: Mosquito Noise Reduction
BNR: Block Noise Reduction
CTI: Color Transient Improvement

32

Input Signal > HDMI

11

HDMI

Congures HDMI input signal.

Auto Automatically congures the input signals.

Input

Color Space

Control with HDMI

Standard

Enhanced

Auto Automatically congures the input signals.

YCbCr(4:4:4)

YCbCr(4:2:2)

RGB Select this when the RGB video signals are input.

On Enables CEC communications.
Off Disables CEC communications.

● The setting is available only if the HDMI terminal is selected.

● Abbreviation

CEC: Consumer Electronics Control

ENGLISH

Select this when the dynamic range of the input images is

16-235.

Select this when the dynamic range of the input images is

0-255.

Select this when the Y Cb Cr(4:4:4) video signals are
input.

Select this when the Y Cb Cr(4:2:2) video signals are
input.

Getting Started

Preparation

Basic Operation

Input Signal > COMP.

12

COMP.

Congures the input signal for the component video input terminals.

Y Pb/Cb Pr/Cr Select this when the component video signals are input.

Color Space

RGB Select this when the RGB video signals are input.

SCART

Select this when RGB video signals and sync signals are

input via the SCART interface for European markets.

● The setting is available only if the component video terminals are selected.

Input Signal > Video/S-Video

13

Video/S-Video

Congures the Video/S-Video input signals.

NTSC Setup Level

Adjust this only when NTSC signals are input via Video or S-Video terminal.

●

Color System

0IRE Adjusts the gradation for signals without the 7.5 IRE setup.

7.5IRE Adjusts the gradation for signals with the 7.5 IRE setup.

Auto Congures the color system automatically.
NTSC Select this when the color system is NTSC.
NTSC4.43 Select this when the color system is NTSC4.43.
PAL Select this when the color system is PAL.
PAL-M Select this when the color system is PAL-M.
PAL-N Select this when the color system is PAL-N.
SECAM Select this when the color system is SECAM.

Settings

Troubleshooting

Others

● The setting is available only when the Video or S-Video input image is projected.

33

4

Settings

Setting Menu (Continued)

Input Signal > Aspect (Video)

14

Aspect (Video)

Congures the screen size of the projected image.

4:3 Sets the screen size of the projected image as 4:3.
16:9 Sets the screen size of the projected image as 16:9.
Zoom Zooms the images. (This item cannot be selected in the case of HD signals.)

● This setting can also be congured from the remote control. ( P16)

● The items cannot be set in the case of PC signals.

Input Signal > Aspect (Computer)

15

Aspect (Computer)

Congures the screen size of the projected image.

Auto

1:1

Full Enlarges the PC signal horizontally/vertically.

Enlarges the PC signal horizontally/vertically until it ts the panel height, and displays
it in the original aspect ratio.

Displays the PC signal corresponding to the panel at one dot per pixel ratio. The PC
screen can be shown in the original size.

● This setting can also be congured from the remote control. ( P16)

● This setting cannot be set in the case of SD or HD signals.

Input Signal > V-Stretch (when HD or SD video signals are input)

16

V-Stretch

When set to “On”, the projected 2.35:1 image will be stretched vertically to the panel resolution.

On The projected 2.35:1 image will be stretched vertically to the panel resolution.
Off Projects the 2.35:1 image as-is. (Black bands will be displayed on the top and bottom.)

● This setting cannot be set in the case of PC signals.

Off

“

” “On”

Input Signal > Picture Position

17

Picture Position

Adjusts the horizontal/vertical position of the projected image.

The position of the image varies depending on the input signals. The image of some signals may not be fully displayed. Adjust the position

●

of image using this menu to display the image properly.

34

Input Signal > Over Scan

18

Over Scan

Selects whether or not to set over scan for the SD video signal.

On Over scan the top, left, bottom and right at 2.5% each.
Off Do not over scan.

This setting is not available when HD signal or PC signal is input.

●

Input Signal > Mask

19

Mask

Masks (Hides) the outer area of the projected image.

2.5% Mask 2.5% of the screen.
5% Mask 5% of the screen.
Off No masking.

● Masking is available only when high denition images are input.

ENGLISH

Getting Started

Preparation

Basic Operation

Input Signal > Film Mode

20

Film Mode

Selects this to view movies shot on lm.

Auto For normal circumstances, select this setting.
Off Select this when you are not watching movies shot on lm.

This setting is not available when a progressive signal is input.

●

Settings

Troubleshooting

Others

35

4

Settings

Setting Menu (Continued)

Installation > Lens Control

21

Lens Control

Controls the individual motorized function of the lens when setting up the projector

Focus Function for adjusting the lens focus.
Zoom Function for adjusting the lens zoom.
Shift Function for adjusting lens shift. (Press the up/down/left/right button to shift the screen).
Image Pattern

Displays the image pattern in conjunction with the above setting items.

On

Off Do not display the image pattern.

Lock

On

Off Enables lens adjustment.

Display Display for “Focus”:
for “Zoom” and “Shift”:

(Picture of big green grids) (Picture of small green grids)

Disables lens adjustment.
A warning message appears when the [LENS] button on the remote control is pressed.

Installation > Pixel Adjust

22

Pixel Adjust

Makes ne adjustments of 1 pixel unit for each minor color shift in the horizontal/vertical direction of the image.

Horiz. Red (Move red to left) 1 to 7 (Move red to right)
Horiz. Green (Move green to left) 1 to 7 (Move green to right)
Horiz. Blue (Move blue to left) 1 to 7 (Move blue to right)
Vert. Red (Move red down) 1 to 5 (Move red up)
Vert. Green (Move green down) 1 to 5 (Moves green up)
Vert. Blue (Move blue down) 1 to 5 (Move blue up)

● The horizontal and vertical directions are reversed when the image is ipped to the left or right, or ipped up or down.

● To adjust, use still images with distinct outlines.

● As the adjustments are minor, the effect may be difcult to see for some images.

Installation > Installation Style

23

Installation Style

Flips the image to the left or right, up or down according to the projection state of the projector.

Front Select this for tabletop front projection.
Ceiling Mount (F) Select this for ceiling front projection.
Rear Select this for tabletop rear projection.
Ceiling Mount (R) Select this for ceiling rear projection.

Installation > Keystone

24

Keystone

Compensates for trapezoidal distortion caused by installation.

If the “Shift Adjustment” is excepting 0%, the image may be projected on the screen incorrectly when trapezoidal distortion is

●

compensated.

(

P22

)

36

ENGLISH

Display Setup > Back Color

25

Back Color

Congures the screen color displayed when there is no input signal.

Blue Sets screen color to “Blue”.
Black Sets screen color to “Black”.

Display Setup > Menu Position

26

Menu Position

Sets the display position of the menu. The possible positions for displaying the menu are at the four corners or at center of
the screen.

Display Setup

Back Color

Menu Position

Menu Display
Line Display

Source Display
Logo

Language

Exit

MENU

Select

Blue

15sec

5sec

English

Operate

On
On

Back

BACK

Getting Started

Preparation

Basic Operation

Display Setup > Menu Display

27

Menu Display

Sets the duration for displaying the menu.

15 sec Display for 15 seconds.
On Always display.

Display Setup > Line Display

28

Line Display

Sets whether to display the input setting when switching the input.

5 sec Display for 5 seconds.
Off Do not display.

Display Setup > Source Display

29

Source Display

Sets whether to display the source of input signals when changing the input.

On Display the source of input signals.
Off Do not display.

Settings

Troubleshooting

Display Setup > Logo

30

Logo

Sets whether to display “Logo” during startup.

On Display for 5 seconds.
Off Do not display.

Others

37

4

Settings

Setting Menu (Continued)

Display Setup > Language

31

Language

Sets the language of the menu display.

Japanese

English English
Deutsch German
Español Spanish
Italiano Italian
Français French
Português Portuguese
Nederlands Dutch
Svenska Swedish
Norsk Norwegian

Русский Russian

Chinese

Function > Lamp Power

32

Lamp Power

Congures the output of the light-source lamp.

Normal For normal circumstances, select this setting. (150W)
High Select this when it is difcult to see the image in a bright room. (200W)

● The setting cannot be changed within approximately 90 seconds after this unit has been turned on.

● Settings cannot be changed within approximately 60 seconds after they are made.

Function > Test Pattern

33

Test Pattern

Display 6 types of test patterns.

This can also be displayed by the remote control. (

●

Function > Off Timer

34

Off Timer

Automatically powers off when there is no operation for a certain duration.

Off Disables the off timer.
1 hour Auto power off after 1 hour.
2 hours Auto power off after 2 hours.
3 hours Auto power off after 3 hours.
4 hours Auto power off after 4 hours.

P16

)

38

ENGLISH

Function > High Altitude Mode

35

High Altitude Mode

Selects this when using the projector in a location of low atmospheric pressure (higher than 900 meters above sea level).

On Enable.
Off Disable.

Information

Input Displays the currently selected video input.

Source

Resolution In the case of PC signal, the resolution is displayed.
H Frequency In the case of PC signal, the horizontal frequency is displayed.
V Frequency In the case of PC signal, the vertical frequency is displayed.

Deep Color

Lamp Time Displays the accumulated hours of usage of the light-source lamp.

Displays the type of the current video input signal.
(If PC signal is input, this item cannot be displayed)

Displays the bit depth (color depth) of the video signals input from the HDMI terminals.
[Deep Color is not displayed when Y Cb Cr (4:2:2) is input.]

Getting Started

Preparation

Basic Operation

Settings

Troubleshooting

Others

39

4

Changing the Initial Setting of

Picture Mode

Settings

Customizing Projected Images

You can adjust the projected image to a desired image quality and register the adjusted value. (Picture
Mode) Besides the ve default “Cinema 1”, “Cinema 2”, “Natural”, “Stage” and “Dynamic” settings, there are

3 more types of user-dened settings for Picture Mode.

STANDBY

LENS

INFO

GAMMA

COLOR

BRIGHT

TEST

MENU

CINEMA1

NATURAL

LENS.AP

TINT

CONT

STAGE

ON

INPUT

ASPECT

C.TEMP

N.R

SHARP

HIDE

BACK

CINEMA2

DYNAMIC

“Contrast”, “Brightness”, “Color”, “Tint”, “Color Temp.”, “Gamma”, “Sharpness”,
“NR”, “CTI” and “Lens aperture” are registered in the Picture Mode.

Select picture mode

1

CINEMA1

NATURAL

2

Adjust picture quality

STAGE

CINEMA2

DYNAMIC

Example: To adjust “Contrast”

1

Display the setting menu

MENU

Select “Picture Adjust”

2

Select

“Contrast”

Picture Adjust

Picture Mode

Contrast
Brightness
Color
Tint
Color Temp.
Gamma
Advanced
Lens Aperture

Exit

MENU

Select

Natural

0
0
0
0

6500K

Normal

2

Reset

Operate

Back

BACK

USER1

USER2

LIGHT

RM-MH2GB

USER3

3 Adjust the setting

Contrast

Adjust

4 To end the adjustments

BACK

Other items can also be adjusted

3

4

To end

MENU

● “Contrast”, “Brightness”, “Color”, “Tint”, “Color

Temp.”, “Gamma”, “Sharpness”, “NR” and “Lens
aperture” can also be adjusted from the remote
control. (

P16)

0

40

ENGLISH

Registering User-dened Picture Mode

Registering User-dened Picture Mode

from the Menu

Getting Started

Select the picture mode

1

USER2USER1

2

Adjust picture quality

● See “Changing the initial setting of picture Mode” for procedures

on adjusting the picture quality. (

3

To end

MENU

Adjust picture quality

1

● See “Changing the Initial Setting of Picture Mode” for procedures

on adjusting the picture quality. (

USER3

P40)

P40)

CAUTION

● Adjustment settings of image quality

will not be registered if other picture
mode is selected before registering

these settings.

Preparation

Basic Operation

2

Display the setting menu

MENU

3

Select “Picture Adjust”

“

4

Picture Mode” “Natural

Select

1

Confirm

2

Register the setting

”

Picture Adjust

Picture Mode

Contrast
Brightness
Color

Tint

Color Temp.

Gamma

Advanced
Lens Aperture

Exit

MENU

Select

Settings

Cinema１

Natural

Cinema２

6500K

Reset

Natural
Stage
Dynamic
User１
User２
User３

2

Back

BACK

Troubleshooting

0
0
0
0

Normal

Operate

Others

41

5

Troubleshooting

Troubleshooting

Before sending the unit to your authorized dealer for repair, please check the following points.

The following situations are not malfunctions.

■

You do not need to worry about the following situations if there is no abnormality on the screen.

● Part of the top surface or front of the unit is hot.

● A creaking sound is heard from the unit.

● An operating sound is heard from the inside of the unit.

● Color smear occurs on some screens.

■

Perform the following operations when the unit is unable to operate normally due to external static or

noise.

When the unit is in standby mode, please pull out the power plug, then insert again.

1

Press the power button on the unit to turn on the power again.

2

■

A sound may be heard when the lamp is off but there is no danger.

■

D-ILA device is manufactured using high-precision technology but there may be some

missing pixels or pixels that remain permanently lit up.

Power is not supplied

Is the power cord disconnected?

Is the lamp cover properly shut?

Is the lamp in Cool Down mode?

Insert the power cord (plug) rmly.

Remove the power plug when the unit is in standby mode and

close the lamp cover properly. After that, insert the plug again.

After the Cool Down mode is complete, turn on the power

again.

Projected image is dark

Check the lamp time on the information menu. Prepare a

Is the lamp near exhaustion?

new lamp unit or replace as soon as possible when the

lamp is near exhaustion.

The unit works when power is turned on but stops abruptly after a few minutes

Are the air inlets and exhaust
vent blocked?

Is the lter dirty?

Remove the power plug when the unit is in standby mode and

remove any blocking object. After that, insert the plug again.
Clean the lter.

Video image does not appear

Is the correct external input
selected?
Is the AV device properly
connected?
Is the power of the AV device turned
on?
Are the correct signals being
output from the AV device?
Is the setting of the input terminal
correct?
Is the video image temporarily
hidden?

Select the correct external input.

Connect the AV device properly.

Turn on the power of the AV device and play the video.

Set the AV device properly.

Set “COMP.” and “HDMI” in the setting menu according to

the input signal.

Press the [HIDE] button to display the video image again.

P24

P47

P25

P46 to 48

P14 to 15

P49

P24

P18 to 21

P24

P18 to 21

P33 -

11 12

P25

42

ENGLISH

The image cannot output by HDMI terminal

“

Is the setup of
function

Even if the “Control with HDMI” function is “On”, there are still some devices cannot reveal image normally.

●

“Off”

Control with HDMI”

?

Set up the “Control with HDMI” function to “Off”.

Color does not appear or looks strange

P33 -

Getting Started

11

Is the image correctly adjusted?

Adjust “Color” and “Tint” in the setting menu.

Video image is fuzzy

Is the focus correctly adjusted? Adjust the focus.
Is the unit placed too near or too far away

from the screen?

Set the unit at a correct distance from the screen.

Video images are missing

Has setting been performed for
screen mask?

Is the display out of position?

Set “Mask” in the setting menu to “Off”.

Alter the “Picture Position” value in the setting menu to

ensure that images are not missing.

Remote control does not work

Are batteries installed correctly?

Are batteries exhausted?

Match the polarities ( or ) correctly when inserting
the batteries.

Replace with new batteries.

Is there an obstructive object
between the remote control and

Remove any obstructive objects.

remote sensor?
Is the remote control held too far
away from the unit?

Hold the remote control closer to the sensor when

using.

P29 -

04 05

P24

P22 to 23

P27，35 -

P34 -

17

P17

P17

P17

P17

19

Preparation

Basic Operation

Settings

Power is cut off suddenly

Has setting been performed for off
timer?

Set “Off Timer” in the setting menu to “Off”.

P38 -

34

Troubleshooting

Others

43

5

Troubleshooting

What to Do When these Messages
Are Displayed

Message Cause (Details)

COMP.

No Input

COMP.

Lamp replacement

Back

BACK

No device is connected to the input terminal.

The input terminal is connected but there is no signal.

Input the video signals.

A video signal that cannot be used in this unit has been input.

Input video signals that can be used.

* The names of input terminals such as COMP. will be displayed in yellow.

This message is displayed when the accumulated lamp time has

exceeded 1900 hours.

To clear the message, press the [Back] button.

Get ready a new lamp unit and replace as soon as possible. Reset the

lamp time after replacing the lamp. (

P46 to 48

)

44

ENGLISH

About Warning Indicators

The accumulated lamp time or warning mode of this unit is displayed by the indicators.
For information on indicator display during normal operation, see “Controls and Features”. (

Indicator

No.

WARNING LAMP STANDBY/ON

10

11

12

13

14

15

16

17

1

2

3

4

5

6

7

8

9

- -

- -

- -

- -

-

-

Light on

(Red)

Blinking

(Red)

Light on

(orange)

Light on

(orange)

Blinking

(orange)

Blinking

(orange)

Light on (Red)

Light on

(Green)

Blinking

(Green)

Blinking (Red)

-

Blinking

Time

Blinking

Frequency

- - -

- - -

0.5

second

0.5

second

continuous

continuous

- - - -

- - - -

0.25

second

-

-

0.25

second

0.25

second

0.25

second

0.25

second

0.25

second

0.25

second

0.25

second

0.25

second

0.25

second

0.25

second

1 time

2 times

3 times

1 time

2 times

3 times

4 times

1 time

2 times

3 times

4 times

Interval

between

Blinks

-

-

0.75

second

0.75

second

0.75

second

0.75

second

0.75

second

0.75

second

0.75

second

0.75

second

0.75

second

0.75

second

0.75

second

Content

During standby

When the power on
(Hide Off)

When the power on
(Hide On)

During cool down

Lamp replacement is near (
(When accumulated lamp time has

exceeded 1900 hours)
Lamp has reached the end of life

(

P46 to 48

(When accumulated lamp time has

exceeded 2000 hours)
Lamp does not light up and unit is

unable to project

Lamp is turned off during projection

Lamp cover is removed

Abnormalities in the power supply

Cooling fan stops

(cooling fan gets caught)

Internal temperature is too high

(abnormal internal temperature)

External temperature is too high

(abnormal external temperature)

Abnormal electrical circuit

(abnormal startup of drive circuit)

Abnormal electrical circuit

(abnormal communication of the

drive circuit)
Abnormal electrical circuit

(abnormal drive circuit of image)

Abnormalities in the automatic lens cover

)

P14

Indicator
display
in normal

conditions.

P46 to 48

Getting Started

)

Preparation

)

Basic Operation

Settings

Troubleshooting

Actions to Be Taken for Warning Mode

When the unit enters into warning mode (No. 7 to 17), it will automatically stop projection, and run the cooling
fan for about 60 seconds.

After the cooling fan has stopped, pull out the power plug from the power outlet.
Then, follow the procedures below.

No. Check Action

7
8

9
17
10
11
12
13
14
15
16

If the warning indication is displayed again, please wait for the cooling fan stopped, then pull out the power plug from the power outlet.
Then call your authorized dealer for repair.

Check that an impact shock has not occurred during operation.

●

Check that the lamp unit and lamp cover are correctly installed.

●

Check that nothing is blocking the auto lens cover.

●

Check that nothing is blocking the air inlets.

●

Check that the external temperature is normal.

●

Turn on the power again.

Leave the unit until it cools down.
After that, turn on the power again.

Others

45

5

Procedure for Lamp Replacement

Troubleshooting

Replacing the Lamp

The lamp is a consumable item. If the image is dark or the lamp is turned off, replace the lamp unit.

● When the lamp replacement time approaches, a message is displayed on the screen and the condition is indicated by the

indicator. (

Pull the power plug from the power

●

outlet. Failure to do so may cause
injuries or electric shocks.

Do not replace the lamp immediately

●

after the unit has been used, and
allow a cooling period of 1 hour

or more before replacement. The

temperature of the lamp is still high

and this may cause a burn.

Do not apply shock to the lamp unit.

●

It may cause lamp blowout.

Do not use ammable air duster to

●

clean the internal parts of the unit.
This may cause re.

P45)

CAUTION

1

Remove the lamp cover

●

Remove the screws with a screwdriver.

MEMO

Usable Lamp Life

The usable lamp life for this unit is

●

approximately 2000 hours. The

usable lamp life of 2000 hours is
merely the average usable life of
lamps and we do not provide any

guarantee for this gure.

The lamp life may not reach

●

2000 hours depending on the

operating conditions.

When the lamp has reached the

●

end of its usable life, deterioration

progresses rapidly.

If the image is dark or the color tone

●

is abnormal, replace the lamp unit

as soon as possible.

Setting "Lamp Power" to "Standard"

●

will help to prolong the lamp life.

Purchasing the Lamp Unit

Please consult your authorized dealer.

■

Lamp Unit

Part No.: BHL5010-S

Loosen the screws on the lamp unit

2

●

Loosen the screws with a screwdriver.

Pull out the lamp unit

3

●

Grasp the handle and pull out the lamp unit.

46

Handle

Install the new lamp unit

4

Handle

ENGLISH

CAUTION

Use only genuine replacement parts

●

for the lamp unit. Also, never attempt
to reuse an old lamp unit. This may
cause a malfunction.

Do not touch the surface of a new lamp.

●

This may shorten the lamp life and

cause lamp blowout.

MEMO

Getting Started

Preparation

Tighten the screws of the new

5

lamp unit

●

Tighten the screws with a screwdriver.

6

Attach the lamp cover

●

Insert the top part (with 2 claws) of the lamp cover into

the unit.

●

Fasten the screws with a screwdriver.

After Replacing the Lamp

Do not place the removed lamp unit at

●

locations that is reachable by children
or near combustible items

Dispose used lamp units in the same

●

way as uorescent lamps. Follow your
local community rules for disposal.

.

Basic Operation

Settings

Troubleshooting

Others

47

5

Resetting Lamp Time

Troubleshooting

Replacing the Lamp (Continued)

STANDBY

LENS

INFO

GAMMA

COLOR

BRIGHT

TEST

MENU

CINEMA1

LENS.AP

TINT

CONT

ON

INPUT

ASPECT

C.TEMP

N.R

SHARP

HIDE

BACK

CINEMA2

After replacing the lamp, reset the lamp time.

Insert the power plug to the power

1

outlet

Light on (Red)

2

Must operate with the remote control

in the standby mode (the projector is
powered, but is not turned on).

Press in the order as shown.

●

Press each button within 2-second intervals and press the last

●

button for 2 seconds or more.

BACK

HIDE

NATURAL

USER1

W ARNING

LAMP

ST ANDBY/ON

STAGE

USER2

LIGHT

DYNAMIC

USER3

CAUTION

Reset the lamp time only when you

●

have replaced the lamp.

Never reset the service time when

●

the lamp is still in use. Otherwise,

the approximate standard for gauging
replacement time may be inaccurate

and lamp blowout may occur.

Press for 2 seconds or more

[STANDBY/ON] indicator and [LAMP] indicator blink alternately for

●

3 seconds. After that, the unit switches to standby mode.

48

ENGLISH

Cleaning and Replacing the Filter

Clean the lter regularly or air intake efciency may deteriorate and malfunction may occur.

Remove the inner lter

1

CAUTION

Getting Started

Lift up while pushing the claw

2

Clean the lter

Wash the lter with water and dry it in a shaded area.

●

In extremely soiled cases, using a neutral detergent is recommended.

●

Put on rubber gloves when using a neutral detergent.

After washing the lter with water, make sure that it is completely dry

●

before reinstalling. Otherwise electric shock or malfunctions may occur.

Do not clean the lter with a vacuum cleaner or air duster. The lter is

●

soft and may be damaged.

Pull the power plug from the power

●

outlet.

Preparation

Basic Operation

MEMO

If the lter is damaged or too

dirty to be cleaned

Replace with a new lter. A dirty lter

●

will dirty the internal parts of the unit
and cause shadows on the video

image.

To purchase a new lter or when it

●

is dirty in the internal parts, consult
your authorized dealer.

■

Inner Filter Part No.:

Replacement Filter:
the appearance is black

PB006560999 (Inner Filter)

the appearance is white

PB006575099 (Inner Filter)

Settings

Troubleshooting

Reinstall the inner lter

3

Check that the left
and right claws are
locked onto the unit

Others

49

Others

Command Format

RS-232C Specications

6

RS-232C Interface

Control of this unit via a computer is possible by connecting the computer to this unit with a RS-232C
cross cable (D-Sub 9 pin).

This unit









Pin No. Signal Function Signal Direction

2 RxD Receive data PC→This unit

3 TxD Transmit data This unit→PC

5 GND Signal ground -

1,4,6 - 9 N/C - -

● PC refers to the controller such as a personal computer.

Mode

Character Length

Parity

Start Bit

Stop Bit

Data rate

Data format

Non-synchronous

8 bit

None

1

1

19200 bps

Binary

D6 D7D4 D5D2 D3D0 D1

Start Bit Stop Bit

The command between this unit and the computer consists of “Header”, “Unit ID”, “Command”, “Data” and “End”.

● Header (1 byte), Unit ID (2 bytes), Command (2 bytes), Data (n bytes), End (1 byte)

■

Header

This binary code indicates the start of communication.

Binary code Type Description

21 Operating command PC→This unit

3F Reference command PC→This unit

40 Response command This unit→PC

This unit→PC

06 ACK

■

Unit ID

This code species the unit. The binary code is xed at “8901”.

(When the command is accepted without error, it returns to

PC)

50

■

Command and data

Operating command and data (Binary code)

Command Type Data description

0000 Connection check

5057 Power supply

4950 Input

5243 Remote Control

Check whether communication is available between this unit

and the PC during standby.

During standby

31: Turn on the power.

During power on

30: Turn off the power. (Standby mode)

During power on
30: S-VIDEO
31: VIDEO

32: COMP.

36: HDMI 1
37: HDMI 2

Sends the same code as the supplied remote control.

Remote control code” (

●

“

P52)

ENGLISH

Getting Started

Preparation

Basic Operation

Reference command and data (Binary code)

Command Type Data description

During standby or power on
30: Standby mode

5057 Power supply

4950 Input

■

End

This code indicates the end of communication. The binary code is xed at

31: Power-on mode
32: During Cool Down mode

34: Warning mode

During power on
30: S-VIDEO
31: VIDEO

32: COMP.

36: HDMI 1
37: HDMI 2

“0A”.

Settings

Troubleshooting

Others

51

Others

6

RS-232C Interface (Continued)

■

Remote control code

Binary code is sent during communication.

●

Remote control button

name

BACK 37 33 30 33 TEST 37 33 35 39

ON 37 33 30 35 STAGE 37 33 36 37

STAND BY 37 33 30 36 CINEMA2 37 33 36 38

INPUT 37 33 30 38 CINEMA1 37 33 36 39

BRIGHT 37 33 30 39 NATURAL 37 33 36 41

CONT 37 33 30 41 DYNAMIC 37 33 36 42

SHARP 37 33 31 34 USER1 37 33 36 43

COLOR 37 33 31 35 USER2 37 33 36 44

TINT 37 33 31 36 USER3 37 33 36 45

N.R 37 33 31 38 INFO 37 33 37 34

HIDE 37 33 31 44 GAMMA 37 33 37 35

LENS.AP 37 33 32 30 C.TEMP 37 33 37 36

Binary code

37 33 30 31 37 33 33 34

37 33 30 32 37 33 33 36

Remote control button

name

Binary code

MENU 37 33 32 45 ASPECT 37 33 37 37

OK 37 33 32 46

LENS 37 33 33 30

52

RS-232C Communication Examples

This section shows the communication examples of RS-232C.

■

Operating command

Type Command Description

Connection check

Power (On)

Power (Off)

Input (COMP.)

Remote Control

(MENU)

■

Reference command

PC→This unit: 21 89 01 00 00 0A
This unit→PC:

PC→This unit: 21 89 01 50 57 31 0A
This unit→PC:

PC→This unit: 21 89 01 50 57 30 0A
This unit→PC: 06 89 01 50 57 0A

PC→This unit: 21 89 01 49 50 32 0A
This unit→PC:

PC→This unit: 21 89 01 52 43 37 33 32 45 0A
This unit→PC:

06 89 01 00 00 0A

06 89 01 50 57 0A

06 89 01 49 50 0A

06 89 01 52 43 0A

ENGLISH

Connection check

When power is turned on from standby

mode

When power is turned off (standby mode)

from power-on mode

When video input is set to component

When the same operation as pressing
the [MENU] button on the remote control

is made

Getting Started

Preparation

Basic Operation

Type Command Description

Power (On)

Input (S-VIDEO)

PC→This unit: 3F 89 01 50 57 0A
This unit→PC: 06 89 01 50 57 0A
This unit→PC: 40 89 01 50 57 31 0A

PC→This unit: 3F 89 01 49 50 0A
This unit→PC: 06 89 01 49 50 0A
This unit→PC: 40 89 01 49 50 30 0A

When information of power-on mode is

acquired

When information of S-VIDEO input is

acquired

Settings

Troubleshooting

Others

53

Others

About Trademarks and Copyrigh

t

Caution

6

Copyright and Caution

HDMI, HDMI logo and high denition multimedia interface

●

are trademarks or registered trademarks of HDMI Licensing

LCC.

D-ILA Device Characteristics

Do not project still pictures or pictures that have still

segments for a long period of time. The still parts of the
picture may remain on the screen.

Take special notice of images on the screens of video

games and computer programs. There is no problem when
playing normal video images such as movies.

When Unit is Unused for a Long
Time

Prolonged disuse of the unit may effect an error on the

functions. Turn on the power occasionally and operate the
unit.

Usage Environment

Avoid direct exposure of screen to direct sunlight and

●

illumination. Block light using a curtain. Images can be
well projected by darkening the brightness of the room.

Do not use this unit in rooms with cigarette smoke or oily

●

smoke. This may cause the unit to malfunction.

Parts Replacement

Maintenance Procedures

Dirt on the cabinet

Gently clean dirt on the cabinet with a soft cloth. In the case

●

of heavy soiling, soak a cloth in water, wring dry and wipe,

followed by wiping again with a dry cloth. Pay attention to

the following as the cabinet may deteriorate in condition or

paint may come off.

● Do not wipe with thinner or benzene.

● Do not spray with volatile chemicals like insecticide.

● Do not allow prolonged contact with rubber or plastic

products.

Dirt in the air inlets

Use a vacuum cleaner to suck up the dirt. Otherwise, use a

●

cloth to wipe off the dirt. If dirt is allowed to accumulate in

the air inlets, the internal temperature cannot be adjusted

and this may cause a malfunction.

Dirt on the lens

● Clean the dirt using commercial blowers or lens cleaning

papers for cleaning glasses and cameras. Do not use
uid-type cleaning agents. This may lead to peeling of the
surface coating lm.

This unit contains parts (optical part, cooling fan, etc.) that
requir e replacement to maintain its functioning. The

estimate d time for parts repla cement vari es greatly

depending on the usage and environment. Please consult
your authorized dealer for replacement.

54

ENGLISH

Mounting this Unit

Measures to prevent the unit from toppling or dropping should be taken for safety reasons and accident

prevention during emergencies including earthquakes.
When mounting this unit on a pedestal or ceiling, remove the 4 feet on the bottom surface and use all the 4

screw holes (M5 screws) to mount.

Ceiling

■

Bottom Surface

4 locations

Air inlets

Air inlets

Getting Started

Preparation

Basic Operation

Precautions for Mounting

Special expertise and techniques are required for mounting

●

this unit. Be sure to ask your dealer or a specialist to
perform mounting.

Depth of the screw holes (screw length) is 23 mm. Use

●

screws shorter than 23 mm but longer than 13 mm.

Using other screws will result in
malfunctioning or cause the unit to drop.

When mounting to a pedestal, ensure sufcient space

●

(foot height of 10 mm or higher) around the unit so that
the air inlets are not blocked.

Do not tilt this unit more than ±5 degrees from side to

●

side when using.

Regardless whether the unit is still under guarantee,

●

JVC is not liable for any product damage caused by

mounting the unit with non-JVC ceiling ttings or when
the environment is not suitable for ceiling-mount.

When using the unit hanging from a ceiling, pay

●

attention to the surrounding temperature. When a

heater is in use, temperature around the ceiling is

higher than expected.

Settings

Troubleshooting

Others

55

Others

6

Specications

Product Name

Model Name

Display Panel/Size

Projection Lens

Light-source Lamp

Screen Size

objection Distance

Color System

Analog Video Input Format

Digital Video Input Format

Resolution

Input Terminals

Video Input

VIDEO

（

）

S-video Input

S-VIDEO

（

）

Component Video Input

COMPONENT

（

）

HDMI Input

HDMI 1, HDMI 2

（

Power Requirements

）

D-ILA Projector

DLA-HD250

, CR/P

*1 *2

/

0.7V(p-p), 75Ω

：

R

*3

D-ILA device

0.7" (1920pixels x 1080pixels) x 3 (Total no. of pixels: Approx. 6.22million)

2.0 x power zoom lens (1.4:1 to 2.8:1)(Zoom/Focus: Power)

200 W Ultra-high pressure mercury lamp [Part No. : BHL5010-S]

Approx. 60" to 200" (Aspect ratio: 16:9)

Approx. 1.8m to 12m

NTSC, NTSC4.43, PAL, PAL-M, PAL-N, SECAM (Auto/Manual switch)

480i, 480p, 576i, 576p, 720p/50Hz, 720p/60Hz, 1080i/50Hz, 1080i/60Hz
480i, 480p, 576i, 576p, 720p/50Hz, 720p/60Hz, 1080i/50Hz, 1080i/60Hz,

1080p/24Hz, 1080p/50Hz, 1080p/60Hz, PC compatible signals ( P57)
1920 dots x 1080 dots

1-line, RCA pin jack x 1

1.0V(p-p), 75Ω

1-line, mini DIN 4 pin x 1
Y：1.0V(p-p), 75Ω
C：0.286V(p-p), 75Ω(NTSC)； 0.3V(p-p), 75Ω(PAL)

1-line, RCA pin jack x 3
Y：1.0V(p-p), 75Ω
C

B/PB

2-line, HDMI 19 pin x 2(HDCP compliant)

AC 110V-240V 50/60 Hz

Power Consumption

Operation Environment

Installation Height
Dimensions

(Width x Height x Depth)

Mass

Accessories

*1 D-ILA is the abbreviation for Direct drive Image Light Amplier.
*2 D-ILA devices are manufactured using extremely high-precision technology. Pixel effectiveness is 99.99%. Only 0.01% or

less of the pixels are either missing or would remain permanently lit up.
*3 HDCP is the abbreviation for High-bandwidth Digital Content Protection system.
The image of HDMI input terminal may not be displayed due to HDCP specication change.

280W (Standby mode: 1W)

Temperature: 5℃ to 35

Humidity: 20% to 80% (No condensation)
(Storage Temperature: -10℃ to 60℃)

Below 1524m

365mm X 167mm X 477.5mm

11.0Kg

(See

P13

)

℃

● Design and specications are subject to change without prior notice.

● Please note that some of the pictures and illustrations may have been abridged, enlarged or contextualized in order to aid

comprehension. Images may differ from the actual product.

56

■

Dimensions

PC compatible signals

ENGLISH

Getting Started

No.

Designation Resolution

1 VGA 60 640 X 480 31.500 60.000 25.200 - - 800 525 640 480

2 VGA 59.94 640 X 480 31.469 59.940 25.175 - - 800 525 640 480

3 SVGA 60 800 X 600 37.879 60.317 40.000 + + 1,056 628 800 600

4 XGA 60 1024 X 768 48.363 60.004 65.000 - - 1,344 806 1,024 768

5 WXGA 60 1280X 768 47.760 60.000 79.998 - + 1,675 796 1,280 768

6 WXGA +60 1440 X 900 55.919 59.999 106.470 - + 1,904 932 1,440 900

7 SXGA 60 1280 X 1024 63.981 60.020 108.000 + + 1,688 1,066 1,280 1,024

8 WSXGA +60 1680 X 1050 65.222 60.002 147.140 - + 2,256 1,087 1,680 1,050

9 WUXGA 60 1920 X 1200 74.038 59.95 154.000 + - 2,080 1,235 1,920 1,200

Images may not be displayed if the above timings are not met.

fh

[kHz]

fv

[Hz]

Dot CLK

[MHz]

H V

Polarity

Total No.

of dots

[dot]

Total No.

of lines

[line]

No. of

effective

dots
[dot]

No. of

effective

lines
[line]

Preparation

Basic Operation

■

Top Surface

■

Front

■

Bottom Surface

(Unit: mm)

Settings

477.5

365

225.4

168

96

297

90.6

64.5

■

Back Surface

236

Troubleshooting

Lens center

Φ42

13

43.5 105

Lamp cover

198

Others

57

Others

6

MEMO

58