JVC CL-S200, CL-S300 Operation Manuals

Important

This operation manual contains important information on how to use the product.

Please make sure to read the safety precautions rst and keep this manual in a safe and

easily accessible place for future reference.

B5A-2228-00

21.3-inch (54 cm) Color LCD Monitor

CL-S200

Operation Manual

Model: CL-S200Bx0xA

- 2 -

Copyright (C) 1991-2, RSA Data Security, Inc. Created 1991. All rights reserved.

License to copy and use this software is granted provided that it is identied as the "RSA Data
Security, Inc. MD5 Message-Digest Algorithm" in all material mentioning or referencing this

software or this function.

License is also granted to make and use derivative works provided that such works are identied
as "derived from the RSA Data Security, Inc. MD5 Message-Digest Algorithm" in all material

mentioning or referencing the derived work.

RSA Data Security, Inc. makes no representations concerning either the merchantability of this

software or the suitability of this software for any particular purpose. It is provided "as is" without

express or implied warranty of any kind.

These notices must be retained in any copies of any part of this documentation and/or software.

* Windows is a registered trademark of Microsoft Corporation in the United States and/or other

countries.
* VESA is a trademark of the Video Electronics Standard Association.
* All other products and company names are trademarks of their respective owners.

Attention!

The monitor orientation can be changed by rotating the LCD panel 90 degrees and the
screen orientation (display mode) can be changed by switching the Extended Display

Identication Data (EDIDs.)

- 3 -

Contents

Before use .........................................................................................................4

Power Cord Important Information ..................................................................6

EMC precaution ...............................................................................................7

Label ..............................................................................................................10

Explanation of symbols ..................................................................................11

Safety precautions ...........................................................................................12

Features ..........................................................................................................16

Names and functions of parts ..........................................................................17

Reference ........................................................................................................19

Operating Principle ..........................................................................................19

Cleaning the monitor .......................................................................................20

Connector pin assignment ...............................................................................21

Technical specication .....................................................................................22

External dimensions ......................................................................................23

After-sales service ...........................................................................................24

Disposal of Electrical and Electronic Equipment .............................................25

- 4 -

Before use

Thank you for purchasing our color LCD CL-S200. Please read this manual carefully for
proper use.

For your safety

This manual contains important information on how to use the product. Please make

sure to read the safety precautions rst and keep this manual in a safe and easily

accessible place for future reference.

Indication for use

CL-S200 is intended to be used in displaying and viewing medical images for diagnosis

by trained medical practitioners or Certied personnel. It is not meant to be used in digital

mammography.

Caution:

Federal law restricts this device to sale by or on the order of a physician.

Limitation of liability

We are not liable for damages

● arising from re, earthquakes, actions taken by any third party, any other accidents,

intentionally or negligently, improper use of the product by the user, or any use under
other abnormal circumstances,

● (including, but not limited to, loss of business prots, disruption of business, change or

loss of saved data) arising from the use of or inability to use this product,

● disassemble or modify, the Company does not take any responsibility.

● arising from the use not described in the instruction manual,

● arising from malfunctions caused by the combination of connecting devices, or

● (related to the time limit, business, decrease in prots, any delay, any information, and

other nancial disadvantages) arising from the use of software provided by us for this

product, even if we have been advised of the possibility of such damages.

Uninterruptible power supply

Instantaneous voltage drop due to, for instance, lightning, could cause a power failure.
We recommend that an uninterruptible power supply system be used to avoid the failure.

FCC information

FCC (U.S. Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and receiver.

● Connect the equipment to an outlet on a circuit different from that to which the receiver

- 5 -

is connected.

● Consult your dealer or an experienced radio/TV technician for help.

Responsible party located within the United States

JVCKENWOOD USA Corporation
1700 Valley Road Wayne, N. J. 07470
TEL: [phone]

FCC Warning

To assure continued FCC compliance, the user must use a grounded power supply cord
and the provided shielded video interface cable with bonded ferrite cores. Also, any

unauthorized changes or modications to this monitor would void the user's authority to

operate this device.

CE certication

This device complies with the requirements of Medical Devices Directive
93/42/EEC.

Manufacturer

JVC KENWOOD Corporation
3-12, Moriya-cho, Kanagawa-ku,
Yokohama-shi, Kanagawa
221-0022, JAPAN

Authorized representative

JVCKENWOOD Deutschland GmbH
Konrad-Adenauer-Allee 1-11, 61118 Vilbel, GERMANY
TEL: [phone] (German, English)
e-mail: [e-mail]

Warning

● This apparatus must be earthed because of Class I equipment.

● This apparatus is not a patient contact equipment.

● When using at 240 V in the United States, supply must be from center-tapped, 240 V,

single phase circuit.

● Consult your dealer about waste disposal.

● This apparatus shall not to be used in the vicinity of the patient, which is the space with

surfaces likely to be contacted by the patient or an attendant who can touch the patient.
This encloses a space within the room 1.83 m (6 feet) beyond the perimeter of the bed

in its intended location, and extending vertically 2.29 m (7-1/ 2 feet) above the oor.

Equipment classication

● Type of protection against electric shock: Class I equipment

● Protection against harmful ingress of water: Ordinary Equipment (IPX0)-No protection.

● Not suitable for use in the presence of ammable anesthetics or oxygen.

● Mode of operation: Continuous operation

- 6 -

Power Cord Important Information

CAUTION: Please use the power cord provided with this monitor in accordance with the

table below. If a power cord is not supplied with this equipment, please contact your sup­plier. For all other cases, please use a power cord that matches the AC voltage of the
power outlet and has been approved by and complies with the safety standards of your
particular country. When you use this Monitor for medical in North America, you should
use a North America Hospital Grade power cord.

Country U.S.A. / Canada EU Japan

Plug Shape

or

Standard UL / CSA

VDE, Demko,

Nemko, BSI. etc.

PSE

Voltage 120 230 100

NOTE: This product can only be serviced in the country where it was purchased.

- 7 -

EMC precaution

• This product requires special EMC precautions and needs to be installed and used

according to the following information.

• Use the specied cable. Using other cables could increase emission or decrease

immunity.

• Do not place any RF communication equipment in the vicinity of this product. It could

affect the performance of the product.

• Any additional equipment connected to this product needs to comply with the

requirements of IEC/EN60601-1-2.

Guidance and manufacturer’s declaration – electromagnetic emissions

The model CL-S200 is intended for use in the electromagnetic environment specied below. The

customer or the user of the model CL-S200 should assure that it is used in such an
environment.

Emissions test Compliance Electromagnetic environment

– guidance

RF emissions CISPR 11 Group 1 The model CL-S200 uses RF energy

only for its internal function. Therefore,
its RF emissions are very low and are
not likely to cause any interference in
nearby electronic equipment.

RF emissions CISPR 11 Class B The model CL-S200 is suitable for use in

all establishments, including domestic
establishments and those directly
connected to the public low-voltage
power supply network that supplies
buildings used for domestic purposes.

Harmonic emissions
IEC 61000-3-2

Class D

Voltage uctuations/icker

emissions
IEC 61000-3-3

Complies

Recommended separation distances between

portable and mobile RF communications equipment and the model CL-S200

The model CL-S200 is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the model CL-S200 can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile
RF communications equipment (transmitters) and the model CL-S200 as recommended below,
according to the maximum output power of the communications equipment.

Rated maximum

output power of

transmitter

W

Separation distance according to frequency of transmitter

m

150 kHz to 80 MHz

d

= 1.2

80 MHz to 800 MHz

d

= 1.2

800 MHz to 2.7 GHz

d

= 2.3

0.01 0.12 0.12 0.23

0.1 0.38 0.38 0.73
1 1.2 1.2 2.3

10 3.8 3.8 7.3

100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended
separation distance

d

in meters (m) can be estimated using the equation applicable to the

frequency of the transmitter, where

P

is the maximum output power rating of the transmitter in
watts (W) according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range

applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is

affected by absorption and reection from structures, objects and people.

- 8 -

Guidance and manufacturer’s declaration – electromagnetic immunity

The model CL-S200 is intended for use in the electromagnetic environment specied below.

The customer or the user of the model CL-S200 should assure that it is used in such an
environment.

Immunity test IEC 60601 test level Compliance level Electromagnetic

environment

–guidance
Electrostatic
discharge (ESD)
IEC 61000-4-2

±8 kV contact

±15 kV air

±8 kV contact

±15 kV air

Floors should be wood,
concrete or ceramic

tile. If oors are

covered with synthetic
material, the relative
humidity should be at
least 30 %.

Electrical fast
transient/burst
IEC 61000-4-4

±2 kV for power
supply lines

±1 kV for input/output
lines at 100 kHz rate

±2 kV for power
supply lines

±1 kV for input/output
lines at 100 kHz rate

Mains power quality
should be that of a
typical commercial or
hospital environment.

Surge
IEC 61000-4-5

±1 kV line(s) to line(s)

±2 kV line(s) to earth

±1 kV line(s) to line(s)

±2 kV line(s) to earth

Mains power quality
should be that of a
typical commercial or
hospital environment.

Voltage dips, short
interruptions and
voltage variations on
power supply input
lines
IEC 61000-4-11

0 %

U

T

; 0,5 cycle
At 0, 45, 90, 135, 180,
225, 270, 315

°

0 %

U

T ;

1 cycle and 70

%

U

T

: 25/30 cycles

At 0

°

0 %

U

T

; 250/300 cycles

0 %

U

T

; 0,5 cycle
At 0, 45, 90, 135, 180,
225, 270, 315

°

0 %

U

T ;

1 cycle and 70

%

U

T

: 25/30 cycles

At 0

°

0 %

U

T

; 250/300 cycles

Mains power quality
should be that of a
typical commercial or
hospital environment. If
the user of the model
CL-S200 requires
continued operation
during power mains
interruptions, it is
recommended that the
model CL-S200 be
powered from an
uninterruptible power
supply or a battery.

Power
frequency (50/60 Hz)

magnetic eld

IEC 61000-4-8

30 A/m 30 A/m Power frequency

magnetic elds should

be at levels
characteristic of a
typical location in a
typical commercial or
hospital environment.

NOTE

U

T

is the a.c. mains voltage prior to application of the test level.

- 9 -

Guidance and manufacturer’s declaration – electromagnetic immunity

The model CL-S200 is intended for use in the electromagnetic environment specied below.

The customer or the user of the model CL-S200 should assure that it is used in such an
environment.

Immunity IEC 60601 test level Compliance

level

Electromagnetic environment

– guidance

Portable and mobile RF
communications equipment should
be used no closer to any part of
the model CL-S200, including
cables, than the recommended
separation distance calculated
from the equation applicable to the
frequency of the transmitter.

Conducted RF
IEC 61000-4-6

3 V/m

0.15 MHz to 80 MHz

6 V/m At ISM
Frequency

3 V/m

6 V/m

Recommended separation
distance

d = 1.2

Radiated RF
IEC 61000-4-3

3 V/m
80 MHz to 2.7 GHz

3 V/m

d = 1.2

80 MHz to 800 MHz

d = 2.3

800 MHz to 2.7 GHz

where P is the maximum output
power rating of the transmitter in
watts (W) according to the
transmitter manufacturer and d is
the recommended separation
distance in meters (m).

Field strengths from xed RF

transmitters, as determined by an
electromagnetic site survey,

a

should be less than the
compliance level in each frequency
range.

b

Interference may occur in the
vicinity of equipment
marked with the
following symbol:

NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies.

NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is

affected by absorption and reection from structures, objects and people.

a

Field strengths from xed transmitters, such as base stations for radio (cellular/cordless)

telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic

environment due to xed RF transmitters, an electromagnetic site survey should be
considered. If the measured eld strength in the location in which the model CL-S200 is used

exceeds the applicable RF compliance level above, the model CL-S200 should be observed
to verify normal operation. If abnormal performance is observed, additional measures may be
necessary, such as reorienting or relocating the model CL-S200.

b

Over the frequency range 150 kHz to 80 MHz, eld strengths should be less than 3 V/m.