Intermediate FrequencyVIF 38.0 MHz (B/G, I, D/,K,M)
SIF 32.5 MHz (5.5 MHz: B/G)
Colour Sub CarrierPAL
SECAM
NTSC
Power InputAC110 V to AC240 V, 50 Hz / 60HzAC160 V to AC240 V, 50 Hz
Power Consumption88 W (Max) / 99 W(Avg)
Picture TubeVisible size: 52 cm measured diagonally ( H : 41.6 cm × V : 31.5 cm)
High Voltage24.5 kV±1.5 kV (at zero beam current)
Speaker6.5cm × 13cm , Oval type × 2
Audio Power Output3 W (monaural)
Aerial Input Terminal75 Ω unbalanced, coaxial
Input Terminal
[Front / Rear]
Output Terminal
[Rear]
Headphone Jack3.5 mm mini jack × 1
Remote Control UnitRM-C1150 (Battery size : AA / R6 / UM-3 × 2)
Video
Audio
Video
Audio
AV-21QMG7/G,
AV-21QMG7/S,
AV-21QMG7B/G
PAL, SECAM
NTSC 4.43
46.25 MHz to 140.25 MHz
147.25 MHz to 423.25 MHz
431.25 MHz to 863.25 MHz
Mid (X to Z+2, S1 to S10) / Super (S11 to S20) / Hyper (S21 to S41) bands
32MHz (6.0 MHz: I)
31.5MHz (6.5 MHz: D/K)
33.5MHz (4.5 MHz: M)
4.43 MHz
4.40625 MHz / 4.25 MHz
3.58 MHz / 4.43 MHz
1 V(p-p), 75 Ω, negative sync, RCA pin jack × 2
500 mV(rms) (-4 dBs), High impedance, RCA pin jack × 2
1 V(p-p), 75Ω, RCA pin jack × 1
500 mV(rms) (-4 dBs), Low impedance, RCA pin jack × 1
AV-21Q17
/ 60Hz
AV-2100QE,
AV-21Q17/L
Design and specifications are subject to change without notice.
1-2 (No.YA552)
Page 3
SECTION 1
PRECAUTION
1.1SAFETY PRECAUTIONS
(1) The design of this product contains special hardware,
many circuits and components specially for safety
purposes. For continued protection, no changes should be
made to the original design unless authorized in writing by
the manufacturer. Replacement parts must be identical to
those used in the original circuits. Service should be
performed by qualified personnel only.
(2) Alterations of the design or circuitry of the products should
not be made. Any design alterations or additions will void
the manufacturer's warranty and will further relieve the
manufacturer of responsibility for personal injury or
property damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These
characteristics are often not evident from visual inspection
nor can the protection afforded by them necessarily be
obtained by using replacement components rated for
higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in
the parts list of Service manual. Electrical components
having such features are identified by shading on the
schematics and by ( ) on the parts list in Service
manual. The use of a substitute replacement which does
not have the same safety characteristics as the
recommended replacement part shown in the parts list of
Service manual may cause shock, fire, or other hazards.
(4) Don't short between the LIVE side ground and
ISOLATED (NEUTRAL) side ground or EARTH side
ground when repairing.
Some model's power circuit is partly different in the GND.
The difference of the GND is shown by the LIVE : ( ) side
GND, the ISOLATED (NEUTRAL) : ( ) side GND and
EARTH : ( ) side GND.
Don't short between the LIVE side GND and ISOLATED
(NEUTRAL) side GND or EARTH side GND and never
measure the LIVE side GND and ISOLATED (NEUTRAL)
side GND or EARTH side GND at the same time with a
measuring apparatus (oscilloscope etc.). If above note will
not be kept, a fuse or any parts will be broken.
(5) If any repair has been made to the chassis, it is
recommended that the B1 setting should be checked or
adjusted (See ADJUSTMENT OF B1 POWER SUPPLY).
(6) The high voltage applied to the picture tube must conform
with that specified in Service manual. Excessive high
voltage can cause an increase in X-Ray emission, arcing
and possible component damage, therefore operation
under excessive high voltage conditions should be kept to
a minimum, or should be prevented. If severe arcing
occurs, remove the AC power immediately and determine
the cause by visual inspection (incorrect installation,
cracked or melted high voltage harness, poor soldering,
etc.). To maintain the proper minimum level of soft X-Ray
emission, components in the high voltage circuitry
including the picture tube must be the exact replacements
or alternatives approved by the manufacturer of the
complete product.
(7) Do not check high voltage by drawing an arc. Use a high
voltage meter or a high voltage probe with a VTVM.
Discharge the picture tube before attempting meter
connection, by connecting a clip lead to the ground frame
and connecting the other end of the lead through a 10kΩ
2W resistor to the anode button.
(8) When service is required, observe the original lead dress.
Extra precaution should be given to assure correct lead
dress in the high voltage circuit area. Where a short circuit
has occurred, those components that indicate evidence of
overheating should be replaced. Always use the
manufacturer's replacement components.
(9) Isolation Check (Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an
isolation check on the exposed metal parts of the cabinet
(antenna terminals, video/audio input and output terminals,
Control knobs, metal cabinet, screw heads, earphone jack,
control shafts, etc.) to be sure the product is safe to operate
without danger of electrical shock.
a) Dielectric Strength Test
The isolation between the AC primary circuit and all metal
parts exposed to the user, particularly any exposed metal
part having a return path to the chassis should withstand a
voltage of 3000V AC (r.m.s.) for a period of one second. (.
. . . Withstand a voltage of 1100V AC (r.m.s.) to an
appliance rated up to 120V, and 3000V AC (r.m.s.) to an
appliance rated 200V or more, for a period of one second.)
This method of test requires a test equipment not generally
found in the service trade.
b) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use
a line isolation transformer during this check.). Using a
"Leakage Current Tester", measure the leakage current
from each exposed metal part of the cabinet, particularly
any exposed metal part having a return path to the chassis,
to a known good earth ground (water pipe, etc.). Any
leakage current must not exceed 0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.2mA AC
(r.m.s.).
Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not
use a line isolation transformer during this check.). Use
an AC voltmeter having 1000Ω per volt or more
sensitivity in the following manner. Connect a 1500Ω
10W resistor paralleled by a 0.15µF AC-type capacitor
between an exposed metal part and a known good earth
ground (water pipe, etc.). Measure the AC voltage
across the resistor with the AC voltmeter. Move the
resistor connection to each exposed metal part,
particularly any exposed metal part having a return path
to the chassis, and measure the AC voltage across the
resistor. Now, reverse the plug in the AC outlet and
repeat each measurement. Any voltage measured must
not exceed 0.75V AC (r.m.s.). This corresponds to
0.5mA AC (r.m.s.).
However, in tropical area, this must not exceed 0.3V AC
(r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
AC VOLTMETER
(HAVING 1000 /V,
OR MORE SENSITIVITY)
0.15 F AC-TYPE
PLACE THIS PROBE
1500 10W
GOOD EARTH GROUND
ON EACH EXPOSED
ME TAL PAR T
(No.YA552)1-3
Page 4
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1FEATURES
PICTURE MODE
This function can adjust the picture settings automatically.
There are USER, VIVID and SOFT in the PICTURE MODE.
RETURN +
This function can set a channel you frequently view to the
Return Channel and you can view that channel at any time with
one-touch.
29 AUDIO-OUT2- Not used61 A-MUTEI Audio muting (Hi:Mute)
30 TV-OUTO Video (Detected PIF signal)62 NC- Not used
31 SIF-OUT/AUD MON OUT 2O Audio (Detected SIF signal)63 REMOTI Remote control
32 EXT AUDIO 2I Audio signal 264 POWER LEDO Lighting for power LED (Hi:Off Low:ON )
Pin nameI/OFunction
CHILD LOCK
VNR
←
Pin
No.
Use this function to prevent children from operating the TV
without parental consent.
This function can reduce the picture noise.
Eng, Ara, Per, Fre, Rus
Pin nameI/OFunction
←←
2
C bus serial data In/Out
2
C bus serial clock
1-4 (No.YA552)
Page 5
SECTION 3
DISASSEMBLY
3.1DISASSEMBLY PROCEDURE
3.1.1 REMOVING THE REAR COVER
• Unplug the power cord.
(1) Remove the 9 screws [A] and 1 screw [B] as shown in
Fig.1.
(2) Withdraw the REAR COVER toward you.
CAUTION:
When reinstalling the rear cover, carefully push it inward after
inserting the MAIN PWB into the REAR COVER groove.
3.1.2 REMOVING THE MAIN PW BOARD
• Remove the REAR COVER.
(1) Slightly raise the both sides of the MAIN PWB by hand.
(2) Withdraw the MAIN PWB backward.
(If necessary, take off the wire clamp and connectors, etc.)
3.1.3 REMOVING THE SPEAKER
• Remove the REAR COVER.
(1) Remove the 2 screws [C].
(2) Withdraw the SPEAKER toward you.
(3) Follow the same steps when removing the other hand
SPEAKER.
3.1.4 REMOVING THE CHOKE COIL
• Remove the REAR COVER.
(1) Remove the 2 screws [D].
(2) Withdraw the CHOKE COIL.
3.1.5 CHECKING THE MAIN PW BOARD
• To check the solder side of the MAIN PWB.
(1) Pull out the MAIN PWB. (Refer to REMOVING THE MAIN
PW BOARD).
(2) The MAIN PW BOARD turns the front side down and erect
it so that you can easily check its solder side.
CAUTIONS:
• Before turning on power, make sure that the CRT earth wire
and other connectors are properly connected.
• When repairing, connect the DEG. COIL to the DEG.
connector on the MAIN PWB.
3.1.6 WIRE CLAMPING AND CABLE TYING
(1) Be sure to clamp the wire.
(2) Never remove the cable tie used for tying the wires
together.
Should it be inadvertently removed, be sure to tie the wires
with a new cable tie.
(No.YA552)1-5
Page 6
SPEAKER
FRONT CABINET
SPEAKER
C
CRT SOCKET PWB
(Within MAIN PWB)
CHOKE COIL
FRONT COTROL PWB
(Within MAIN PWB)
C
D
POWER CORD
REAR COVER
MAIN PWB
A
B
1-6 (No.YA552)
Fig.1
Page 7
3.2MEMORY IC REPLACEMENT
• This model uses the memory IC.
• This memory IC stores data for proper operation of the video and drive circuits.
• When replacing, be sure to use an IC containing this (initial value) data.
3.2.1 MEMORY IC REPLACEMENT PROCEDURE
1. Power off
Switch off the power and disconnect the power plug from the
KEY ASSIGNMENT OF REMOTE CONTROL UNIT
AC outlet.
2. Replace the memory IC
Be sure to use the memory IC written with the initial setting
values.
PICTURE
MODE key
3. Power on
Connect the power plug to the AC outlet and switch on the
power.
OK key
4. System constant check and setting
• It must not adjust without adjustment signals.
(1) Press the [DISPLAY] key and the [PICTURE MODE]
MENU
/ key
key of the REMOTE CONTROL UNIT simultaneously.
(2) The SERVICE MENU screen of Fig. 1 will be displayed.
(3) While the SERVICE MENU is displayed, again press the
DISPLAY key
[DISPLAY] key and the [PICTURE MODE] key
simultaneously, and the SYSTEM CONSTANT SET
screen of Fig. 2 will be displayed.
(4) Check the setting values of the SYSTEM CONSTANT
SETTING. If the value is different, select the setting item
with the [MENU /] key, and set the correct value with
the [MENU - / +] key.
(5) Press the [DISPLAY] key twice, and return to the normal
screen.
5. Receiving channel setting
Refer to the OPERATING INSTRUCTIONS and set the
receive channels (Channels Preset) as described.
6. User settings
Check the user setting items according to the given in page
later.
Where these do not agree, refer to the OPERATING
INSTRUCTIONS and set the items as described.
7. SERVICE MENU setting
Verify what to set in the SERVICE MENU, and set whatever is
necessary (Fig.1).
Refer to the SERVICE ADJUSTMENT for setting.
OFF
TIMER ECO
MENU
OK
SERVICE MENU
1.IF 2.V/C
3.DEF 4.VSM W/B
5.PRESET
6.PLUG & PLAY (OFF)
7.HOTEL MODE (OFF)
1-7 : SELECT DISP : EXIT
Fig.1
SYSTEM CONSTANT
SYSTEM CONSTANT
SYSTEM
LANGUAGE
BLUE BACK MUTE
COLOR AUTO
BILINGUAL
EXT BPF
PICTURE BOOSTER : NO
Setting itemSetting valueSetting itemSetting value
1. IF1.VCO
2.DELAY POINT
2. V/C1.CUTOFF (R/B/G)
2.WRD (G/B)
3.BRIGHT (TV/VDO 1,2)
4.CONT. (TV/VDO 1,2)
5.COLOUR (TV/VDO 1,2)
6.TINT (TV/VDO 1,2)
7.SHARP (TV/VDO 1,2)
8.Y DELAY (TV/VDO 1,2)
9.VNR STATUS(AUTO)
3. DEFLECTION1.VER POS
2.VER SIZE
3.VER LIN
4.HOR POS
5.HOR BOW
6.HOR PARA
7.VER BLK
8.VER CENT
9.V.S-CR
10.HOR SIZE
11.EW PIN
12.TRAPEZ
13.COR-UP
14.COR-LO
15.HOR EHT
16.VER EHT
4. VSM/WBCONT.
BRIGHT
SHARP
COLOUR
TINT
WDR G
WDR B
5. PRESET
[Do not adjust]
1.OVER MOD
2. N BUZZ
3.S TARP A
4. S TRAP F0
5.STRAP Q
6.SHARP GD
7.S. TRAP HP/LP
8.AF AMP SPEED
9.PIF FREQ
10.AU MON
11.ALC
(No.YA552)1-9
Page 10
3.3REPLACEMENT OF CHIP COMPONENT
3.3.1 CAUTIONS
(1) Avoid heating for more than 3 seconds.
(2) Do not rub the electrodes and the resist parts of the pattern.
(3) When removing a chip part, melt the solder adequately.
(4) Do not reuse a chip part after removing it.
3.3.2 SOLDERING IRON
(1) Use a high insulation soldering iron with a thin pointed end of it.
(2) A 30w soldering iron is recommended for easily removing parts.
3.3.3 REPLACEMENT STEPS
1. How to remove Chip parts
2. How to install Chip parts
[Resistors, capacitors, etc.]
(1) As shown in the figure, push the part with tweezers and
alternately melt the solder at each end.
(2) Shift with the tweezers and remove the chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply extra solder to each lead.
SOLDER
SOLDER
[Resistors, capacitors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on the
solder. Then heat and melt the solder at both ends of the
chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on the
solder.
(3) First solder lead A as indicated in the figure.
(2) As shown in the figure, push the part with tweezers and
alternately melt the solder at each lead. Shift and remove
the chip part.
NOTE :
After removing the part, remove remaining solder from the
pattern.
1-10 (No.YA552)
A
B
C
(4) Then solder leads B and C.
A
B
C
Page 11
SECTION 4
ADJUSTMENT
4.1ADJUSTMENT PREPARATION
(1) There are 2 ways of adjusting this TV : One is with the
REMOTE CONTROL UNIT and the other is the
conventional method using adjustment parts and
components.
(2) The adjustment using the REMOTE CONTROL UNIT is
made on the basis of the initial setting values. The
setting values which adjust the screen to the optimum
condition can be different from the initial setting
values.
(3) Make sure that connection is correctly made AC to AC
power source.
(4) Turn on the power of the TV and measuring instruments for
warming up for at least 30 minutes before starting
adjustments.
(5) If the receive or input signal is not specified, use the most
appropriate signal for adjustment.
(6) Never touch the parts (such as variable resistors,
transformers and condensers) not shown in the adjustment
items of this service adjustment.
4.2PRESET SETTING BEFORE ADJUSTMENT
Unless otherwise specified in the adjustment items, preset the
following functions with the REMOTE CONTROL UNIT.
ItemPreset value
PICTURE MODEVIVID
PICTURE SETTING FOR USER MODECentre
VNROFF
BLUE BACKOFF
OFF TIMEROFF
4.3MEASURING INSTRUMENT AND FIXTURES
(1) DC voltmeter (or digital voltmeter)
(2) Oscilloscope
(3) Signal generator
(Pattern generator : PAL / SECAM / NTSC)
(4) Remote control unit
(5) High voltmeter (with 1000MΩ input impedance)
4.4ADJUSTMENT ITEMS
CHECK ITEM
• B1 VOLTAGE check
• HIGH VOLTAGE check
TUNER / IF CIRCUIT
• IF VCO adjustment
• DELAY POINT adjustment
FOCUS
• FOCUS adjustment
DEFLECTION CIRCUIT
• V.POSITION adjustment
• V.SIZE adjustment
• V.LINEARITY adjustment
• V.S-CURVE adjustment
• H.POSITION adjustment
• H.BOW adjustment
• H.PARALLEL adjustment
• H. SIZE adjustment
• SIDE PIN adjustment
• TRAPEZIUM adjustment
• CORNER PIN adjustment
VIDEO CIRCUIT
• WHITE BALANCE adjustment
• SUB BRIGHT adjustment
• SUB CONTRAST adjustment
• SUB COLOUR adjustment
• SUB TINT adjustment
VSM/WB SETTING
• VSM adjustment
(No.YA552)1-11
Page 12
4.5ADJUSTMENT LOCATIONS
MAIN PWB ASS'Y
(CRT SOCKET)
POWER
CORD
DEG COIL
FRONT
MAIN PWB ASS'Y
(FRONT LED)
CN10A
POWER SW
S901
PW
DEG
CN00A
S804 S802
S805
1
6
TOP
S803 S801
T
1
6
TP-47/R
TP-47/G
(BRAIDED ASS'Y)
J808
J807
IC702
T
E2
CRT EARTH
J806
41
CN00S
J809
(SOLDER SIDE)
TP-47B
E1
41
CRT EARTH
(BRAIDED ASS'Y)
U
FRONT
MAIN PWB ASS'Y
IC701
J804J801 J802 J803
CN00C
61
TU001
CN00C
1. 5V
I2C
2. SCL0
3. SDA0
4. SCL1
5. SDA1
6. GND
U
41
GND
B1
3
1
CN00B
CN00B
1. B1
2. NC
3. GND
HV
14
HVT
UPPER : FOCUS
LOWER : SCREEN
DEF
YOKE
1-12 (No.YA552)
Page 13
4.6BASIC OPERATION OF SERVICE MENU
4.6.1 TOOL OF SERVICE MENU OPERATION
Operate the SERVICE MENU with the REMOTE CONTROL UNIT.
4.6.2 SERVICE MENU ITEMS
With the SERVICE MENU, various adjustments can be made, and they are broadly classified in the following items of settings.
1.IFAdjustment of the IF circuits.
2.V/CAdjustment of the VIDEO circuit.
3.DEFAdjustment of the DEFLECTION circuit.
4.VSM/WBAdjustment of the initial setting values of VSM condition as SOFT and USER.
5.PRESETAdjustment of the RF circuit [Do not adjust].
4.6.3 HOW TO ENTER THE SERVICE MENU
Press the [DISPLAY] key and the [PICTURE MODE] key of
the REMOTE CONTROL UNIT simultaneously. Then enter the
SERVICE MENU SELECT KEY
SERVICE MENU mode as shown in Fig.1.
OFF
MENU
TIMER ECO
OK
NUMBERS
key
MENU
/ key
SERVICE MENU
1.IF 2.V/C
3.DEF 4.VSM W/B
5.PRESET
6.PLUG & PLAY (OFF)
7.HOTEL MODE (OFF)
1-7 : SELECT DISP : EXIT
Fig.1
PICTURE
MODE key
OK key
MENU
/ key
4.6.4 HOW TO STORE OF SETTING VALUE
The setting value will be stored automatically when release the
REMOTE CONTROL UNIT keys.
4.6.5 HOW TO EXIT THE SERVICE MENU
Press the [DISPLAY] key from the state of SERVICE MENU.
DISPLAY key
(No.YA552)1-13
Page 14
4.6.6 METHOD OF SETTING
1. IF
[1. VCO]
(1) [1] keySelect 1. IF.
(2) [1] keySelect 1. VCO.
Check the arrow position between the ABOBE REF. and BELOW REF.
(4) [DISPLAY] keyAs you press this key twice, you will return to the SERVICE MENU.
[2. DELAY POINT]
(1) [1] keySelect 1. IF.
(2) [2] keySelect 2. DELAY POINT.
(3) [MENU /] keysSet (adjust) the setting values of the setting items.
(4) [DISPLAY] keyWhen this is pressed twice, you will return to the SERVICE MENU.
2. V/C, 3. DEF and 4. VSM W/B
(1) [2] to [4] keysSelect one from 2. V/C, 3. DEF and 4. VSM W/B.
(2) [MENU /] keysSelect setting items.
(3) [MENU /] keysAdjust the values of the items.
(4) [DISPLAY] keyWhen this is pressed, you will return to the SERVICE MENU.
5. PRESET (Do not adjust)
1-14 (No.YA552)
Page 15
4.6.7 SERVICE MENU FLOW CHART
SERVICE MENU
SERVICE MENU
1.IF
3.DEF
5. PRESET
6.PLUG & PLAY (OFF)
7.HOTEL MODE (OFF)
2.V/C
4.VSM W/B
1. IF
IF SERVICE MENUVCO(CW) 210.25 MHz
1.VCO
2.DELAY POINT
TOO HIGH
ABOVE REFERENCE
JUST REFERENCE
BELOW REFERENCE
TOO LOW
1-7 SELECT
DISP: EXIT
DISP:EXITDISP:EXIT
2. V/C
V/CPAL
1.CUT OFF
( R ) 20
BRIGHT :40INITIAL:40
(G) 20 (B) 20
: SEL
: OPER
3. DEF
DEF 50 Hz
1. VER POS 00
: SEL
: OPER
4. VSM W/B
VSM SOFT
1. CONT + 0
: SEL
: OPER
DISP:EXIT
DISP:EXIT
DISP:EXIT
DELAY POINTVHF
4:3/16:9
WDR G
WDR B
17
DISP:EXIT
9.V-S .CR
10.HOR SIZE
11.EW PIN
12.TRAPEZ
13.COR-UP
14.COR-LO
15.HOR EHT
16.VER EHT
RF AGC
: OPER
SETTING ITEMS
1.VER POS
2.VER SIZE
3.VER LIN
4.HOR POS
5.HOR BOW
6.HOR PARA
7.VER BLK
8.VER CENT
SETTING ITEMS
1.CUTOFF (R/G/B)
2.WDR (G/B)
3.BRIGHT (TV/VDO 1,2)
4.CONT. (TV/VDO 1,2)
5.COLOUR (TV/VDO 1,2)
6.TINT (TV/VDO 1,2)
7.SHARP (TV/VDO 1,2)
8.Y DELAY (TV/VDO 1,2)
SOFT / USER
SETTING ITEMS
1.CONT. 4.COLOUR
2.BRIGHT 5.TINT
3.SHARP
WARM / NORMAL
SETTING ITEMS
6. PLUG & PLAY
SERVICE MENU
1.IF
3.DEF
5. PRESET
6.PLUG & PLAY (OFF)
7.HOTEL MODE (OFF)
1-7 SELECT
2.V/C
4.VSM W/B
DISP: EXIT
5. PRESET
PRESET AUTO
1. OVER MOD0
50HzD/K
: SEL
: OPER
7. HOTEL MODE
SERVICE MENU
1.IF
3.DEF
5. PRESET
6.PLUG & PLAY (OFF)
7.HOTEL MODE (OFF)
1-7 SELECT
2.V/C
4.VSM W/B
DISP:EXIT
DISP: EXIT
SETTING ITEMS
1.OVER MOD 7.S. TRAP HP/LP
2.N BUZZ 8.AF AMP SPEED
3.S TARP A 9.PIF FREQ
4.S TRAP F0 10.AU MON
5.STRAP Q 11.ALC
6.SHARP GD
(No.YA552)1-15
Page 16
4.7INITIAL SETTING VALUE OF SERVICE MENU
• Adjustment of the SERVICE MENU is made on the basis of the initial setting values ; however, the new setting values which
set the screen in its optimum condition may differ from the initial setting.
• Do not change the initial Setting Values of the Setting (Adjustment) items not listed in "ADJUSTMENT PROCEDURE".
• The " --- " means adjustment is not possible.
• " * " is variable values for adjustment and other value variable when have problem only.
[2. V/C] (Values for adjustment indicate in hexadecimal number.)
[AV-2100QE, AV-21Q17, AV-21Q17/L]
Setting itemVariable range
PALSECAMNTSC 3.58NTSC 4.43
Initial setting value
1.CUT OFFR00 - FF20*
G00 - FF20*
B00 - FF20*
2.WDRG00 - FF40*
B00 - FF40*
3.BRIGHTRF00 - (+127)+65*
VIDEO-1(-128) - (+127)-01
VIDEO-2(-128) - (+127)00
4.CONT.RF00 - (+127)+107
VIDEO-1(-128) - (+127)
VIDEO-2(-128) - (+127)
+07
5.COLOURRF00 - (+127)+67+64------
VIDEO-1(-128) - (+127)
VIDEO-2(-128) - (+127)
-02-6-01+08
6.TINTRF00 - (+127)+67+65------
VIDEO 1/2(-128) - (+127)-02-03+07+6
7.SHARPRF 00 - (+63)+40+40+40
VIDEO 1/2 00 - (+63)+45+40+45
8.Y DELAYRF 00 - 0703010200
VIDEO 1/2 00 - 0702000005
9.VNR STATUSRF---
VIDEO 1/2---
---
1-16 (No.YA552)
Page 17
[AV-21QMG7/G, AV-21QMG7/S, AV-21QMG7B/G]
Setting itemVariable range
PALSECAMNTSC 3.58NTSC 4.43
Initial setting value
1.CUT OFFR00 - FF20*
G00 - FF20*
B00 - FF20*
2.WDRG00 - FF40*
B00 - FF40*
3.BRIGHTRF00 - (+127)+65*
VIDEO-1(-128) - (+127)-01
VIDEO-2(-128) - (+127)-00
4.CONT.RF00 - (+127)+107
VIDEO-1(-128) - (+127)
VIDEO-2(-128) - (+127)
+07
5.COLOURRF00 - (+127)+67+64+69+06
VIDEO-1(-128) - (+127)
VIDEO-2(-128) - (+127)
-02-06-01+08
6.TINTRF00 - (+127)+67+65+57+04
VIDEO 1/2(-128) - (+127)-02-03+07+06
7.SHARPRF 00 - (+63)+40+40+40
VIDEO 1/2 00 - (+63)+45+40+45
8.Y DELAYRF 00 - 0703010200
VIDEO 1/2 00 - 0702000005
9.VNR STATUSRF---
VIDEO 1/2---
---
[3. DEFLECTION] (Values for adjustment indicate in hexadecimal number.)
Initial setting value
Setting item
Variable range
50Hz60Hz50Hz60Hz
1.VER. POS00 - 0F00 - 0F0000
2.VER. SIZE00 - 3FC0 - 3F2A*00*
3. VER LIN00 - 1FE0 - FF0D*00*
4. HOR POS00 - 1FE0 - FF0A*03*
5. HOR BOW00 - 0703*03*
6. HOR PARA00 - 0703*03*
7. VER BLK00 - 0F0404
8. VER CENT00 - 3F21*00*
9. V.S-CR00 - 1FE0 - 1F19*00*
10. HOR SIZE30*00*
11. EW-PIN45*00*
12. TRAPEZ23*00*
13. COR-UP0A*0A*
14. COR-LOW0B*0B*
15. H EHT0404
16. V EHT0404
(No.YA552)1-17
Page 18
[4. VSM/WB] (Values for adjustment indicate in hexadecimal number.)
Setting itemVariable range
Initial setting value
SOFTUSER
CONT.80 - 7FDF00
BRIGHT80 - 7F0000
SHARP80 - 7FFA00
COLOUR80 - 7F0000
TINT80 - 7F0000
Setting item
WARMNORMAL
Initial setting value
WDR GF407
WDR BEAF9
[5. PRESET] (Do not adjust)
The items in the following table, it is no requirement for adjustment.If values had changed by the miss operation, set the
initial setting values in the following table.
Setting itemVariable range
MB/GID/K
Initial setting value
1. OVER MOD00 - 0100
2. N BUZZ00 - 0101
3. S TRAP A00 - 0100000000
4. S TRAP F000 - 0F08060808
5. S TRAP Q00 - 0302020201
6. S TRAP GD00 - 0301000000
7. S TRAP HP/LP00 - 0300000000
8. AF AMP SPEED00 - 0100
9. PIF FREQ00 - 0300
10. AU MOM00 - 0300
11. ALCFC - FFFF
[6.PLUG & PLAY]
Setting of the last memory for shipment to “ON”.
When this mode is ON, the TV can be turned on/off power by connecting/disconnecting the AC plug into AC outlet.
[7.HOTEL MODE]
Setting of the last memory for shipment to “OFF”.
When this mode is ON, all keys except following ones are invalid.
[POWER / CHANNEL,VOLUME +- / 10KEY / MUTING / "TV/VIDEO" / OFF TIMER / "-/--" / DISPLAY]
(1) Receive a whole black signal.
(2) Connect a DC voltmeter to 1-pin and 5-pin of S1
connector.
(3) Make sure that the voltage is DC115.2V±2.0V.
(1) Receive any broadcast.
(2) Connect the earth clip of High voltmeter to chassis
GND.
(3) Connect the probe of High voltmeter to CRT anode.
(4) Make sure that the voltage is DC24.5kV ±1.5kV.
NOTE:
• Remove the probe before removing the earth clip.
Test pointAdjustment partDescription
[1.IF]
1.VCO
• Under normal conditions, no adjustment is required.
• Confirmation adjustment.
(1) Select 1.IF from the SERVICE MENU.
(2) Select <1.VCO>
(3) Receive any broadcast.
(4) Check the ←(Arrow) position between the ABOVE
REF. and BELOW REF.
IF SERVICE MENU
1. VCO
2. DELAY POINT
DISPLAY : EXIT
Receiving frequency
VCO (CW)
TOO HIGH
ABOVE REFERENCE
JUST REFERENCE
BELOW REFERENCE
TOO LOW
. MHz
DISPLAY : EXIT
YELLOW
(No.YA552)1-19
Page 20
Item
DELAY POINT
(AGC)
Measuring
instrument
Test pointAdjustment partDescription
Signal
generator
Remote
control unit
DELAY POINT VHF
RF AGC **
- / + : OPERATE DISP : EXIT
[1. IF]
2. DELAY POINT
(AGC TAKE-OVER)
(1) Receive a black and white signal (colour off).
(2) Select 1. IF.
(3) Select <2. DELAY POINT>.
(4) Set the setting values of the setting items as shown
bellow table.
(5) Adjust the [MENU /] keys until video noise
disappears.
(6) Turn to other channels and make sure that there are
no irregularities.
Setting Item
DELAY POINT
(AGC TAKE-OVER)
NTSC3.58
OTHER
4.8.3 FOCUS
Item
Measuring
instrument
FOCUSSignal
generator
Variable range
0 - 127
Initial setting value
17
17
Test pointAdjustment partDescription
FOCUS VR
[In HVT]
(1) Receive a crosshatch signal.
(2) While looking at the screen center, adjust the
FOCUS VR to make the vertical and horizontal lines
as fine and sharp as possible.
(3) Make sure that when the screen is darkened, the
lines remain in good focus.
1-20 (No.YA552)
Page 21
4.8.4 DEFLECTION CIRCUIT
• There are 2 modes of adjustment (setting value) 50Hz mode and 60Hz mode, depending upon the kind of signals (vertical frequency
50Hz / 60Hz).
• When adjusted in 50Hz mode and 60Hz mode will be automatically set.
The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values.The setting
values which adjust the screen to the optimum condition can be different from the initial setting values.
• Make sure that the adjustment is properly done on the screen of 60Hz mode.
NOTE:
• Adjust to make both 50Hz & 60Hz are the same V. size and fine straight line.
• When adjust again, adjust 50Hz mode first.
• When adjust in 60Hz mode, only 60Hz mode is adjust.
Item
V. POSITION /
V. SIZE
Measuring
instrument
Signal
generator
Remote
control unit
Test pointAdjustment partDescription
[3. DEF]
1. VER. POS
2. VER. SIZE
(1) Receive a crosshatch signal.
(2) Select 3. DEF from the SERVICE MENU.
(3) Select <1. VER. POS>.
(4) Set the initial setting value of <1. VER. POS>.
(5) Adjust <1. VER. POS> to make the vertical centre
fall on the display centre.
(6) Select <2. VER. SIZE>.
(7) Set the initial setting value of <2. VER. SIZE>.
Screen
size
92%
Picture
size
100%
(8) Adjust <2. VER. SIZE> to make the vertical screen
size be 92% of the picture size.
V.LINEARITY /
V-S.CURVE
Signal
generator
Remote
control unit
H. POSITIONSignal
generator
Remote
control unit
(A)
[3. DEF]
3. VER. LIN.
9. V.S-CR
Top
Centre
Bottom
[3. DEF]
4. HOR. POS
(B)
• If the vertical linearity is noticeably deteriorated, perform
the following steps.
(1) Receive a crosshatch signal.
(2) Select 3. DEF from the SERVICE MENU.
(3) Select <3. VER. LIN.>.
(4) Set the initial setting value of <3. VER. LIN.>.
(5) Select <9. V.S-CR>.
(6) Set the initial setting value of <9. V.S-CR>.
(7) Adjust <3. VER. LIN.> and <9. V.S-CR> so that the
space of upper and lower lines on TOP, CENTRE
and BOTTOM become uniform.
(1) Receive a circle pattern signal.
(2) Select 3. DEF from the SERVICE MENU.
(3) Select <4. HOR. POS>.
(4) Set the initial setting value of <4. HOR. POS>.
(5) Adjust <4.HOR. POS> to be equal the width of (A)
and (B).
(No.YA552)1-21
Page 22
Item
Measuring
instrument
H. BOWSignal
generator
Remote
control unit
Test pointAdjustment partDescription
[4.DEF]
5. HOR BOW
(1) Receive a crosshatch signal.
(2) Select 4. DEF from the SERVICE MENU.
(3) Select <5. HOR BOW>.
(4) Set the initial setting value of <5. HOR BOW>.
(5) Adjust <5. HOR BOW> to straighten the vertical arc
Straight
distortion.
H. PARALLELSignal
generator
Remote
control unit
H. SIZESignal
generator
Remote
control unit
Parallel
Screen size 91%
[4.DEF]
6. HOR PARA
[4.DEF]
10. H-SIZE
(1) Receive a crosshatch signal.
(2) Select 4. DEF from the SERVICE MENU.
(3) Select <6. HOR PARA>.
(4) Set the initial setting value of <6. HOR PARA>.
(5) Adjust <6. HOR PARA> to straighten with parallel
the trapezium distortion at the centre of the screen.
PAL H. SIZE
(1) Receive a PAL crosshatch signal.
(2) Select 4. DEF from the SERVICE MODE.
(3) Select <10. H-SIZE>.
(4) Set the initial setting value of <10. H-SIZE>.
(5) Adjust <10. H-SIZE> to make the horizontal screen
size to 91% of the picture size.
(6) Press the [OK] key to memorize the set values.
NTSC H. SIZE
(1) Receive a NTSC crosshatch signal.
(2) Follow the same step 2 to 6 as in PAL H. SIZE.
Picture size 100%
1-22 (No.YA552)
Page 23
Item
Measuring
instrument
SIDE PINSignal
generator
Remote
control unit
Test pointAdjustment partDescription
[4. DEF]
11. EW-PIN
PAL S I D E P I N
(1) Receive a PAL crosshatch signal.
(2) Select 4. DEF from the SERVICE MODE.
(3) Select <11. EW-PIN>.
(4) Set the initial setting value of <11. EW-PIN>.
Straight
(5) Adjust <11. EW-PIN> so that the first vertical lines at
the left and right edges on the screen are straight.
(6) Press the [OK] key to memorize the set values.
NTSC SIDE PIN
(1) Receive a NTSC crosshatch signal.
(2) Follow the same step 2 to 6 as in PAL SIDE PIN.
TRAPEZIUMSignal
generator
Remote
control unit
CORNER PINSignal
generator
Remote
control unit
Parallel
Straigt
[4.DEF]
12. TRAPEZ
[4. DEF]
13. COR-UP
14. COR-LO
PAL TRAPEZIUM
(1) Receive a PAL crosshatch signal.
(2) Select 4. DEF from the SERVICE MODE.
(3) Select <12. TRAPEZ>.
(4) Set the initial setting value of 12. TRAPEZ.
(5) Adjust <12. TRAPEZ> so that the vertical lines at the
left and right edges on the screen are in parallel.
(6) Press the [OK] key to memorize the set values.
NTSC TRAPEZIUM
(1) Receive a NTSC crosshatch signal.
(2) Follow the same step 2 to 6 as in PAL TRAPEZIUM.
PAL CORNER PIN
(1) Receive a PAL crosshatch signal.
(2) Select 4. DEF from the SERVICE MODE.
(3) Select <13. COR-UP>.
(4) Set the initial setting value of <13. COR-UP>.
(5) Select <14. COR-LO>.
(6) Set the initial setting value of <14. COR-LO>.
(7) Adjust <13. COR-UP> and <14. COR-LO> so that
the vertical lines at the four corners on the screen
are straight.
(8) Press the [OK] key to memorize the set values.
NTSC CORNER PIN
(1) Receive a NTSC crosshatch signal.
(2) Follow the same step 2 to 8 as in PAL CORNER.
(No.YA552)1-23
Page 24
4.8.5 VIDEO CIRCUIT
Item
WHITE
BALANCE
(LOW LIGHT)
Measuring
instrument
Signal
generator
Remote
control unit
KEY ASSIGNMENT OF REMOTE CONTROL UNIT
H.LINE ON/OFF
R. CUT OFF( )
Test pointAdjustment partDescription
123
456
[2.V/C]
1. CUT OFF (R)
1. CUT OFF (G)
1. CUT OFF (B)
SCREEN VR
[IN HVT]
G.CUT OFF( )
B. CUT OFF( )
(1) Receive a 100% all white signal (colour off).
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <1. CUT OFF>.
(4) Set the initial setting value of <1. CUT OFF>.
(5) Press the [1] key to show the single horizontal line
on screen.
(6) Turn the SCREEN VR fully counter-clockwise, then
slowly turn it clockwise to where one of a red, blue or
green colour is faintly visible.
(7) Adjust the two colors which did not appear until the
single horizontal line that is displayed becomes
white using the [4] to [9] keys.
(8) Turn the SCREEN VR to where the single horizontal
line glows faintly.
(9) Press the [1] key to turn off the single horizontal line.
R. CUT OFF( )
WHITE
BALANCE
(HIGH LIGHT)
Signal
generator
Remote
control unit
KEY ASSIGNMENT OF REMOTE CONTROL UNIT
G. DRIVE( )
SUB BRIGHTRemote
control unit
SUB
CONTRAST
Remote
control unit
789
R G B
123
456
789
GB
B. CUT OFF( )
G.CUT OFF( )
[2.V/C]
2. WDR (G)
2. WDR (B)
B. DRIVE( )
B. DRIVE( )G. DRIVE( )
[2. V/C]
3. BRIGHT
[2. V/C]
4. CONT.
(1) Receive a 100% all white signal (colour off).
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <2. WDR>.
(4) Set the initial setting value of <2. WDR>.
(5) Adjust the screen until it becomes white using the
[5], [8], [6] and [9] keys.
(1) Receive any broadcast.
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <3. BRIGHT>.
(4) Set the initial setting value of <3. BRIGHT>.
(5) If the brightness is not the best with the initial setting
value, make fine adjustment until you get the best
brightness.
(1) Receive any broadcast.
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <4. CONT>.
(4) Set the initial setting value of <4. CONT>.
(5) If the contrast is not the best with the initial setting
value, make fine adjustment until you get the best
contrast.
1-24 (No.YA552)
Page 25
Item
Measuring
instrument
SUB COLOURRemote
control unit
Signal
generator
Oscilloscope
Remote
control unit
AV-21Q17
AV-21Q17/L
AV-2100QE
AV-21QMG7/G
AV-21QMG7/S
AV-21QMG7B/G
Test pointAdjustment partDescription
[2. V/C]
5. COLOUR
[Method of adjustment without measuring instrument]
PAL COLOUR
(1) Receive a PAL broadcast.
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <5. COLOUR>.
(4) Set the initial setting value of <5. COLOUR>.
(5) If the colour is not the best with the initial setting
value, make fine adjustment until you get the best
colour.
SECAM COLOUR
(1) Receive a SECAM broadcast.
(2) Make fine adjustment of SECAM COLOUR as
previously.
NTSC 3.58 COLOUR
(1) Receive a NTSC 3.58MHz broadcast.
(2) Make similar fine adjustment of NTSC 3.58
COLOUR as previously.
NTSC 4.43 COLOUR
(1) When NTSC 3.58 adjustment completed, NTSC
4.43 will be automatically set at the respective
values.
TP-47R/G
TP-E
[CRT SOCKET
PWB]
[2. V/C]
5. COLOUR
[Method of adjustment using measuring instrument]
PAL COLOUR
(1) Receive a PAL full field colour bar signal (75%
white).
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <5. COLOUR>.
(4) Set the initial setting value of <5. COLOUR>.
(5) Connect the oscilloscope to TP-47R/G and TP-E.
(6) Adjust PAL COLOUR to bring the value of (A) in
the voltage table.
SECAM COLOUR
(1) Receive a SECAM full field colour bar signal (75%
white).
(2) Set the initial setting value of SECAM COLOUR .
(3) Adjust SECAM COLOUR to bring the value of (A)
in the voltage table.
NTSC 3.58 COLOUR
(1) Receive a NTSC 3.58 full field colour bar signal
(75% white).
(2) Set the initial setting value of NTSC 3.58
COLOUR.
(3) Adjust NTSC 3.58 COLOUR to bring the value of
(A) in the voltage table.
Mg R BW Y Cy G
(A) : W-G
(A)
(-)
(0)
(+)
NTSC 4.43 COLOUR
Voltage setting (A)
PALNTSC3.58SECAM
+18V+17V (VDO)+16V
+18V+21V (RF)+16V
(1) When NTSC 3.58 is set, NTSC 4.43 will be
automatically set at the respective values.
(No.YA552)1-25
Page 26
Item
Measuring
instrument
SUB TINTSignal
generator
Remote
control unit
Signal
generator
Oscilloscope
Remote
control unit
Test pointAdjustment partDescription
[2. V/C]
6. TINT
[Method of adjustment without measuring instrument]
PAL TINT
(1) Receive a PAL broadcast.
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <6. TINT>.
(4) Set the initial setting value of <6. TINT>.
(5) If you cannot get the best tint with the initial setting
value, make fine adjustment until you get the best
tint.
NTSC 3.58 TINT
(1) Receive a NTSC 3.58MHz broadcast.
(2) Make similar fine adjustment of NTSC 3.58 TINT
as previously.
NTSC 4.43 TINT
(1) When NTSC 3.58 is set, NTSC 4.43 will be
automatically set at the respective values.
TP-47R/G
TP-E
[CRT SOCKET
PWB]
[2. V/C]
6. TINT
[Method of adjustment using measuring instrument]
PAL TINT
(1) Receive a PAL full field colour bar signal (75%
white).
(2) Select 2. V/C from the SERVICE MENU.
(3) Select <6. TINT>.
(4) Set the initial setting value of <6. TINT>.
(5) Connect the oscilloscope to TP-47R/G and TP-E.
(6) Adjust PAL TINT to bring the value of (B) in the
voltage table in the left.
NTSC 3.58 TINT
(1) Receive a NTSC 3.58 full colour bar signal (75%
white).
(2) Set the initial setting value of NTSC 3.58 TINT.
(3) Adjust NTSC 3.58 TINT to bring the value of (B) in
the voltage table in the left.
Mg R BW Y Cy G
(B) : W-Cy
(-)
(B)
(0)
(+)
NTSC 4.43 TINT
(1) When NTSC 3.58 is set, NTSC 4.43 will be
automatically set at the respective values.
Voltage setting (B)
PALNTSC3.58
AV-21Q17
AV-21Q17/L
AV-2100QE
AV-21QMG7/G
AV-21QMG7/S
AV-21QMG7B/G
+14V+17V (VDO)
+14V+15V (RF)
1-26 (No.YA552)
Page 27
4.8.6 VSM/WB SETTING
VSM
W/B
Item
Measuring
instrument
VSM/WB Remote
control unit
Test pointAdjustment partDescription
[4. VSM]
CONT.
BRIGHT
SHARP
COLOUR
TINT
WDR G
WDR B
(1) Select 4. VSM from the SERVICE MENU.
(2) Select PICTURE MODE to "SOFT".
(3) Select <CONT.>.
(4) Set the initial setting value of <CONT.> as shown in
the below table.
(5) Select <BRIGHT> to <TINT> in turn, and set the
values.
(6) Respectively select the "USER". Make similar
adjustment as same step as above.
(7) Select WHITE BALANCE to "WARM".
(8) Select <WDR G>.
(9) Set the initial setting value of <WDR G> as shown in
the below table.
(10) Select <WDR B>, and set the values.
(11) Respectively select the "NORMAL". Make similar
adjustment as same step as above.
VSM
Setting item
CONT.
BRIGHT
SHARP
COLOUR
TINT
W/B
Setting item
WDR.G
WDR.B
Setting value
SOFT
DF
00
FA
00
00
Setting value
WARM
F4
EA
USER
00
00
00
00
00
NORMAL
07
F9
(No.YA552)1-27
Page 28
SECTION 5
TROUBLESHOOTING
5.1SELF CHECK FUNCTIONS
5.1.1 OUTLINE
This model has self check functions given below. When an abnormality has been detected, the SUB POWER is turned off and POWER
LED flashes to inform of the failure. An abnormality is detected by the signal input state of the control line connected to the microcomputer.
5.1.2 SELF CHECK ITEMS
Check itemDetails of detectionMethod of detectionState of abnormality
B1 over-current protectionAn over-current on the low B1
line is detected.
CRT neck broken protectionOperation of CRT neck protec-
tion circuit.
5.1.3 SELF CHECK INDICATING FUNCTION
When an abnormality has been detected at about 5 seconds after the power was turned on, the SUB POWER is turned off immediately and the POWER LED flashes.
The main microcomputer detects the possible abnormality at
24-msec. intervals and judges
the results in every 16 time. Of
the 16 times, if NG is detected
more than 9 times, it is judged
that there is an abnormality.
After about
5 seconds
When an abnormality has been
detected, the SUB-POWER is
turned off. While the SUB-POWER is being turned off, the
POWER key on the remote control unit is not operational until
the power cord is disconnected
and connected again.
The components identified by thesymbol and shading are
critical for safety. For continued safety replace safety ciritical
components only with manufactures recommended parts.
2.SPECIFIED VOLTAGE AND WAVEFORM VALUES
The voltage and waveform values have been measured under the
following conditions.
(1)Input signal: Colour bar signal
(2)Setting positions of
each knob/button and
variable resistor
(3)Internal resistance of tester
(4)Oscilloscope sweeping time
(5)Voltage values
Since the voltage values of signal circuit vary to some extent
according to adjustments, use them as reference values.
Composition resistor 1/2 [W] is specified as 1/2S or Comp.
(2)Capacitors
Capacitance value
1 or higher: [pF]
less than 1
Withstand voltage
No indication: DC50[V]
Others: DC withstand voltage [V]
AC indicated
Electrolytic Capacitors
47/50[Example]: Capacitance value [µF]/withstand voltage[V]
: [kΩ]
: [MΩ]
: Carbon resistor
: Oxide metal film resistor
: Metal film resistor
: Metal plate resistor
: Uninflammable resistor
: Fusible resistor
: [µF]
: AC withstand voltage [V]
(7)Ground symbol
: LIVE side ground
: ISOLATED(NEUTRAL) side ground
: EARTH ground
: DIGITAL ground
5.NOTE FOR REPAIRING SERVICE
This model's power circuit is partly different in the GND. The
difference of the GND is shown by the LIVE : ( ) side GND and the
ISOLATED(NEUTRAL) : ( ) side GND. Therefore, care must be
taken for the following points.
(1)Do not touch the LIVE side GND or the LIVE side GND and the
ISOLATED(NEUTRAL) side GND simultaneously. if the above
caution is not respected, an electric shock may be caused.
Therefore, make sure that the power cord is surely removed from
the receptacle when, for example, the chassis is pulled out.
(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL
side GND or never measure with a measuring apparatus measure
with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND
and ISOLATED(NEUTRAL) side GND at the same time.
If the above precaution is not respected, a fuse or any parts will be broken.
Since the circuit diagram is a standard one, the circuit and
circuit constants may be subject to change for improvement
without any notice.
NOTE
Due improvement in performance, some part numbers show
in the circuit diagram may not agree with those indicated in
the part list.
When ordering parts, please use the numbers that appear
in the Parts List.
OM RMetal Oxide Film ResistorPP CAP.Polypropylene Capacitor
CMF RCoating Metal Film ResistorPS CAP.Polystyrol Capacitor
UNF RNon-Flammable ResistorTF CAP.Thin Film Capacitor
CH V RChip Variable ResistorMPP CAP.Metalized Polypropylene Capacitor
CH MG RChip Metal Glazed ResistorTAN. CAP.Tantalum Capacitor
COMP. RComposition ResistorCH C CAP.Chip Ceramic Capacitor
LPTC RLinear Positive Temperature Coefficient ResistorBP E CAP.Bi-Polar Electrolytic Capacitor
CH AL E CAP.Chip Aluminum Electrolytic Capacitor
CH AL BP CAP.Chip Aluminum Bi-Polar Capacitor
CH TAN. E CAP.Chip Tantalum Electrolytic Capacitor
CH AL BP E CAP.Chip Tantalum Bi-Polar Electrolytic Capacitor
RESISTORS
FGJ KMNRHZ P
±1%±2%±5%±10%±20%±30%
+30%
-10%
+50%
-10%
+80%
-20%
+100%
-0%
(No.YA552)3-1
Page 39
CONTENTS
USING P.W. BOARD & REMOTE CONTROL UNIT ................................................................................................... 3-2
EXPLODED VIEW PARTS LIST ................................................................................................................................. 3-3
PACKING PARTS LIST ............................................................................................................................................. 3-20
C001NCB31HK-103XC CAPACITOR0.01uF 50V K
C002QETN1HM-336ZE CAPACITOR33uF 50V M
C005NCB31HK-103XC CAPACITOR0.01uF 50V K
C006QETN1AM-477ZE CAPACITOR470uF 10V M
C007NCB31HK-103XC CAPACITOR0.01uF 50V K
C008QETN1HM-106ZE CAPACITOR10uF 50V M
C101NCB31HK-472XC CAPACITOR4700pF 50V K
C102QETN1EM-476ZE CAPACITOR47uF 25V M
C103NCB31HK-472XC CAPACITOR4700pF 50V K
C104NCB31HK-472XC CAPACITOR4700pF 50V K
C105NCB31HK-472XC CAPACITOR4700pF 50V K
C106NCB31HK-472XC CAPACITOR4700pF 50V K
C107NCB31HK-104XC CAPACITOR0.1uF 50V K
C108NCB31HK-103XC CAPACITOR0.01uF 50V K
C109QETN1CM-477ZE CAPACITOR470uF 16V M
C351QFZ0097-103MM CAPACITOR0.01uF 1250V K
C352QETN1CM-477ZE CAPACITOR470uF 16V M
C354NDC31HJ-331XC CAPACITOR330pF 50V J
C355NDC31HJ-271XC CAPACITOR270pF 50V J
C356NDC31HJ-391XC CAPACITOR390pF 50V J
C357QETN1AM-477ZE CAPACITOR470uF 10V M
C422QCS32HJ-180ZC CAPACITOR18pF 500V J
C423NCB31HK-682XC CAPACITOR6800pF 50V K
C424QFLC2AJ-683ZM CAPACITOR0.068uF 100V J
C427QETM1HM-108E CAPACITOR1000uF 50V M
C428QETN1HM-227ZE CAPACITOR220uF 50V M
C430QFLC2AJ-563ZM CAPACITOR0.056uF 100V J
C431QFVF1HJ-184ZMF CAPACITOR0.18uF 50V J
C435NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C436NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C471QETN1HM-226ZE CAPACITOR22uF 50V M
C521QCB31HK-332ZC CAPACITOR3300pF 50V K
C522QFLC1HJ-223ZM CAPACITOR0.022uF 50V J
C523QETN1VM-476ZE CAPACITOR47uF 35V M
C525QFZ0196-143MPP CAPACITOR0.014uF 1.5kV H
C526QFZ0196-113MPP CAPACITOR0.011uF 1.5kV H
C527QFZ0197-404MPP CAPACITOR0.4uF 250V J
C528QFP32GJ-393PP CAPACITOR0.039uF 400V J
C529QENC2AM-225ZBP E CAPACITOR2.2uF 100V M
C530QCB32HK-561ZC CAPACITOR560pF 500V K
C531QEZ0195-475ZBP E CAPACITOR4.7uF 50V M
C532QETN2EM-106ZE CAPACITOR10uF 250V M
C533QFZ0197-105MPP CAPACITOR1uF 250V J
C542QFZ0197-823MPP CAPACITOR0.082uF 250V J
C551QCB32HK-561ZC CAPACITOR560pF 500V K
C552QCB32HK-561ZC CAPACITOR560pF 500V K
C553QETN1EM-108ZE CAPACITOR1000uF 25V M
C554QETN1EM-108ZE CAPACITOR1000uF 25V M
C555QFLC2AJ-103ZM CAPACITOR0.01uF 100V J
C571QEZ0203-107E CAPACITOR100uF 160V M
C572QETN1CM-107ZE CAPACITOR100uF 16V M
C573QETN1VM-476ZE CAPACITOR47uF 35V M
C581QFVF1HJ-104ZMF CAPACITOR0.1uF 50V J
C591QETN1VM-476ZE CAPACITOR47uF 35V M
C601QETN1CM-107ZE CAPACITOR100uF 16V M
C603QETN1HM-105ZE CAPACITOR1uF 50V M
C604QETN1HM-106ZE CAPACITOR10uF 50V M
C605QETN1HM-106ZE CAPACITOR10uF 50V M
C606QETN1HM-107ZE CAPACITOR100uF 50V M
C607QETN1HM-106ZE CAPACITOR10uF 50V M
C608NCB31CK-224XC CAPACITOR0.22uF 16V K
C609NCB31CK-224XC CAPACITOR0.22uF 16V K
C610QETN1HM-106ZE CAPACITOR10uF 50V M
C611QETN1CM-477ZE CAPACITOR470uF 16V M
C701QETN1CM-107ZE CAPACITOR100uF 16V M
C702NCB31HK-104XC CAPACITOR0.1uF 50V K
C710NCB31HK-103XC CAPACITOR0.01uF 50V K
C711NCB31HK-103XC CAPACITOR0.01uF 50V K
C712NDC31HJ-220XC CAPACITOR22pF 50V J
C713NDC31HJ-220XC CAPACITOR22pF 50V J
C714NCB31HK-103XC CAPACITOR0.01uF 50V K
C715QETN1CM-107ZE CAPACITOR100uF 16V M
C716NCB31HK-822XC CAPACITOR8200pF 50V K
C717QETN1HM-474ZE CAPACITOR0.47uF 50V M
C718QFLC2AJ-104ZM CAPACITOR0.1uF 100V J
C719QETN1HM-225ZE CAPACITOR2.2uF 50V M
C720NCB31HK-103XC CAPACITOR0.01uF 50V K
C721NCB31HK-103XC CAPACITOR0.01uF 50V K
C723NCB31HK-103XC CAPACITOR0.01uF 50V K
(No.YA552)3-5
Page 43
Ref No. Part No.Part NameDescription Local
Ref No. Part No.Part NameDescription Local
C724QETN1HM-106ZE CAPACITOR10uF 50V M
C725QENC1HM-105ZBP E CAPACITOR1uF 50V M
C726QETN1HM-106ZE CAPACITOR10uF 50V M
C727NCB31HK-104XC CAPACITOR0.1uF 50V K
C728NCB31HK-104XC CAPACITOR0.1uF 50V K
C729QETN1HM-106ZE CAPACITOR10uF 50V M
C730QETN1EM-476ZE CAPACITOR47uF 25V M
C731QETN1HM-474ZE CAPACITOR0.47uF 50V M
C732NCB31HK-102XC CAPACITOR1000pF 50V K
C733NCB31HK-103XC CAPACITOR0.01uF 50V K
C734QETN1HM-475ZE CAPACITOR4.7uF 50V M
C735QETN1HM-225ZE CAPACITOR2.2uF 50V M
C736NCB31HK-103XC CAPACITOR0.01uF 50V K
C737QETN1HM-105ZE CAPACITOR1uF 50V M
C738NCB31HK-222XC CAPACITOR2200pF 50V K
C739NCB31CK-224XC CAPACITOR0.22uF 16V K
C740QETN1CM-107ZE CAPACITOR100uF 16V M
C741NCB31HK-103XC CAPACITOR0.01uF 50V K
C743QETN1HM-106ZE CAPACITOR10uF 50V M
C744NCB31HK-103XC CAPACITOR0.01uF 50V K
C745QETN1CM-107ZE CAPACITOR100uF 16V M
C747NCB31HK-103XC CAPACITOR0.01uF 50V K
C748QETN1EM-476ZE CAPACITOR47uF 25V M
C754NDC21HJ-100XC CAPACITOR10pF 50V J
C755NCB31HK-104XC CAPACITOR0.1uF 50V K
C801QETN1HM-225ZE CAPACITOR2.2uF 50V M
C803QETN1HM-105ZE CAPACITOR1uF 50V M
C804QETN1HM-105ZE CAPACITOR1uF 50V M
C805QETN1HM-225ZE CAPACITOR2.2uF 50V M
C808QETN1AM-477ZE CAPACITOR470uF 10V M
C809QETN1HM-106ZE CAPACITOR10uF 50V M
C810QETN1HM-105ZE CAPACITOR1uF 50V M
C901QFZ9072-224MM CAPACITOR0.22uF AC250V K
C902QFZ9072-224MM CAPACITOR0.22uF AC250V K
C903QFZ9072-224MM CAPACITOR0.22uF AC250V K
C904QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C905QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C906QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C910QEZ0633-227E CAPACITOR220uF 450V M
C911QCZ0364-561C CAPACITOR560pF 2kV K
C912QETN1VM-226ZE CAPACITOR22uF 35V M
C913NCB31HK-103XC CAPACITOR0.01uF 50V K
C914NCB31HK-104XC CAPACITOR0.1uF 50V K
C915QFLC1HJ-471ZM CAPACITOR470pF 50V J
C918QCB32HK-103C CAPACITOR0.01uF 500V K
C951QCZ0364-102C CAPACITOR1000pF 2kV K
C952QCB32HK-471ZC CAPACITOR470pF 500V K
C953QCB32HK-471ZC CAPACITOR470pF 500V K
C954QCB32HK-471ZC CAPACITOR470pF 500V K
C955QCB32HK-471ZC CAPACITOR470pF 500V K
C961QEZ0203-107E CAPACITOR100uF 160V M
C963QETN1AM-108ZE CAPACITOR1000uF 10V M
C964QETN1EM-477ZE CAPACITOR470uF 25V M
C965QETN1VM-477ZE CAPACITOR470uF 35V M
C966QETN1EM-108ZE CAPACITOR1000uF 25V M
C971QETN1EM-107ZE CAPACITOR100uF 25V M
C972NCB31HK-104XC CAPACITOR0.1uF 50V K
C973QETN1AM-107ZE CAPACITOR100uF 10V M
C974QETN1AM-107ZE CAPACITOR100uF 10V M
C975QETN1AM-107ZE CAPACITOR100uF 10V M
C976QETN1EM-107ZE CAPACITOR100uF 25V M
C977QETN1AM-108ZE CAPACITOR1000uF 10V M
C981NRSA63J-0R0XMG RESISTOR0
C983QETN1CM-107ZE CAPACITOR100uF 16V M
C991QCZ9079-102C CAPACITOR1000pF AC250V M
C992QCZ9079-102C CAPACITOR1000pF AC250V M
C993QCZ9079-102C CAPACITOR1000pF AC250V M
C994QFLC1HJ-102ZM CAPACITOR1000pF 50V J
C001NCB31HK-103XC CAPACITOR0.01uF 50V K
C002QETN1HM-336ZE CAPACITOR33uF 50V M
C005NCB31HK-103XC CAPACITOR0.01uF 50V K
C006QETN1AM-477ZE CAPACITOR470uF 10V M
C007NCB31HK-103XC CAPACITOR0.01uF 50V K
C008QETN1HM-106ZE CAPACITOR10uF 50V M
C101NCB31HK-472XC CAPACITOR4700pF 50V K
C102QETN1EM-476ZE CAPACITOR47uF 25V M
C103NCB31HK-472XC CAPACITOR4700pF 50V K
C104NCB31HK-472XC CAPACITOR4700pF 50V K
C105NCB31HK-472XC CAPACITOR4700pF 50V K
C106NCB31HK-472XC CAPACITOR4700pF 50V K
C107NCB31HK-104XC CAPACITOR0.1uF 50V K
C108NCB31HK-103XC CAPACITOR0.01uF 50V K
C109QETN1CM-477ZE CAPACITOR470uF 16V M
C111NCB31CK-103XC CAPACITOR0.01uF 16V K
C112NCB31CK-103XC CAPACITOR0.01uF 16V K
C113NCB31CK-103XC CAPACITOR0.01uF 16V K
C351QFZ0097-103MM CAPACITOR0.01uF 1250V K
C352QETN1CM-477ZE CAPACITOR470uF 16V M
C354NDC31HJ-331XC CAPACITOR330pF 50V J
C355NDC31HJ-271XC CAPACITOR270pF 50V J
C356NDC31HJ-391XC CAPACITOR390pF 50V J
C357QETN1AM-477ZE CAPACITOR470uF 10V M
C422QCS32HJ-180ZC CAPACITOR18pF 500V J
C423NCB31HK-682XC CAPACITOR6800pF 50V K
C424QFLC2AJ-683ZM CAPACITOR0.068uF 100V J
C427QETM1HM-108E CAPACITOR1000uF 50V M
C428QETN1HM-227ZE CAPACITOR220uF 50V M
C430QFLC2AJ-563ZM CAPACITOR0.056uF 100V J
C431QFVF1HJ-184ZMF CAPACITOR0.18uF 50V J
C435NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C436NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C471QETN1HM-226ZE CAPACITOR22uF 50V M
C521QCB31HK-332ZC CAPACITOR3300pF 50V K
C522QFLC1HJ-223ZM CAPACITOR0.022uF 50V J
C523QETN1VM-476ZE CAPACITOR47uF 35V M
C525QFZ0196-143MPP CAPACITOR0.014uF 1.5kV H
C526QFZ0196-113MPP CAPACITOR0.011uF 1.5kV H
C527QFZ0197-404MPP CAPACITOR0.4uF 250V J
C528QFP32GJ-393PP CAPACITOR0.039uF 400V J
C529QENC2AM-225ZBP E CAPACITOR2.2uF 100V M
C530QCB32HK-561ZC CAPACITOR560pF 500V K
C531QEZ0195-475ZBP E CAPACITOR4.7uF 50V M
C532QETN2EM-106ZE CAPACITOR10uF 250V M
C533QFZ0197-105MPP CAPACITOR1uF 250V J
C542QFZ0197-823MPP CAPACITOR0.082uF 250V J
C551QCB32HK-561ZC CAPACITOR560pF 500V K
C552QCB32HK-561ZC CAPACITOR560pF 500V K
C553QETN1EM-108ZE CAPACITOR1000uF 25V M
C554QETN1EM-108ZE CAPACITOR1000uF 25V M
C555QFLC2AJ-103ZM CAPACITOR0.01uF 100V J
C571QEZ0203-107E CAPACITOR100uF 160V M
C572QETN1CM-107ZE CAPACITOR100uF 16V M
C573QETN1VM-476ZE CAPACITOR47uF 35V M
C581QFVF1HJ-104ZMF CAPACITOR0.1uF 50V J
C591QETN1VM-476ZE CAPACITOR47uF 35V M
C601QETN1CM-107ZE CAPACITOR100uF 16V M
C603QETN1HM-105ZE CAPACITOR1uF 50V M
C604QETN1HM-106ZE CAPACITOR10uF 50V M
C605QETN1HM-106ZE CAPACITOR10uF 50V M
C606QETN1HM-107ZE CAPACITOR100uF 50V M
C607QETN1HM-106ZE CAPACITOR10uF 50V M
C608NCB31CK-224XC CAPACITOR0.22uF 16V K
C609NCB31CK-224XC CAPACITOR0.22uF 16V K
C610QETN1HM-106ZE CAPACITOR10uF 50V M
C611QETN1CM-477ZE CAPACITOR470uF 16V M
C701QETN1CM-107ZE CAPACITOR100uF 16V M
C702NCB31HK-104XC CAPACITOR0.1uF 50V K
C710NCB31HK-103XC CAPACITOR0.01uF 50V K
C711NCB31HK-103XC CAPACITOR0.01uF 50V K
C712NDC31HJ-220XC CAPACITOR22pF 50V J
C713NDC31HJ-220XC CAPACITOR22pF 50V J
C714NCB31HK-103XC CAPACITOR0.01uF 50V K
C715QETN1CM-107ZE CAPACITOR100uF 16V M
C716NCB31HK-822XC CAPACITOR8200pF 50V K
C717QETN1HM-474ZE CAPACITOR0.47uF 50V M
C718QFLC2AJ-104ZM CAPACITOR0.1uF 100V J
C719QETN1HM-225ZE CAPACITOR2.2uF 50V M
3-8(No.YA552)
Page 46
Ref No. Part No.Part NameDescription Local
Ref No. Part No.Part NameDescription Local
C720NCB31HK-103XC CAPACITOR0.01uF 50V K
C721NCB31HK-103XC CAPACITOR0.01uF 50V K
C723NCB31HK-103XC CAPACITOR0.01uF 50V K
C724QETN1HM-106ZE CAPACITOR10uF 50V M
C725QENC1HM-105ZBP E CAPACITOR1uF 50V M
C726QETN1HM-106ZE CAPACITOR10uF 50V M
C727NCB31HK-104XC CAPACITOR0.1uF 50V K
C728NCB31HK-104XC CAPACITOR0.1uF 50V K
C729QETN1HM-106ZE CAPACITOR10uF 50V M
C730QETN1EM-476ZE CAPACITOR47uF 25V M
C731QETN1HM-474ZE CAPACITOR0.47uF 50V M
C732NCB31HK-102XC CAPACITOR1000pF 50V K
C733NCB31HK-103XC CAPACITOR0.01uF 50V K
C734QETN1HM-475ZE CAPACITOR4.7uF 50V M
C735QETN1HM-225ZE CAPACITOR2.2uF 50V M
C736NCB31HK-103XC CAPACITOR0.01uF 50V K
C737QETN1HM-105ZE CAPACITOR1uF 50V M
C738NCB31HK-222XC CAPACITOR2200pF 50V K
C739NCB31CK-224XC CAPACITOR0.22uF 16V K
C740QETN1CM-107ZE CAPACITOR100uF 16V M
C741NCB31HK-103XC CAPACITOR0.01uF 50V K
C743QETN1HM-106ZE CAPACITOR10uF 50V M
C744NCB31HK-103XC CAPACITOR0.01uF 50V K
C745QETN1CM-107ZE CAPACITOR100uF 16V M
C747NCB31HK-103XC CAPACITOR0.01uF 50V K
C748QETN1EM-476ZE CAPACITOR47uF 25V M
C754NDC21HJ-100XC CAPACITOR10pF 50V J
C755NCB31HK-104XC CAPACITOR0.1uF 50V K
C801QETN1HM-225ZE CAPACITOR2.2uF 50V M
C803QETN1HM-105ZE CAPACITOR1uF 50V M
C804QETN1HM-105ZE CAPACITOR1uF 50V M
C805QETN1HM-225ZE CAPACITOR2.2uF 50V M
C808QETN1AM-477ZE CAPACITOR470uF 10V M
C809QETN1HM-106ZE CAPACITOR10uF 50V M
C810QETN1HM-105ZE CAPACITOR1uF 50V M
C901QFZ9072-224MM CAPACITOR0.22uF AC250V K
C902QFZ9072-224MM CAPACITOR0.22uF AC250V K
C903QFZ9072-224MM CAPACITOR0.22uF AC250V K
C904QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C905QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C906QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C910QEZ0633-227E CAPACITOR220uF 450V M
C911QCZ0364-561C CAPACITOR560pF 2kV K
C912QETN1VM-226ZE CAPACITOR22uF 35V M
C913NCB31HK-103XC CAPACITOR0.01uF 50V K
C914NCB31HK-104XC CAPACITOR0.1uF 50V K
C915QFLC1HJ-471ZM CAPACITOR470pF 50V J
C918QCB32HK-103C CAPACITOR0.01uF 500V K
C951QCZ0364-102C CAPACITOR1000pF 2kV K
C952QCB32HK-471ZC CAPACITOR470pF 500V K
C953QCB32HK-471ZC CAPACITOR470pF 500V K
C954QCB32HK-471ZC CAPACITOR470pF 500V K
C955QCB32HK-471ZC CAPACITOR470pF 500V K
C961QEZ0203-107E CAPACITOR100uF 160V M
C963QETN1AM-108ZE CAPACITOR1000uF 10V M
C964QETN1EM-477ZE CAPACITOR470uF 25V M
C965QETN1VM-477ZE CAPACITOR470uF 35V M
C966QETN1EM-108ZE CAPACITOR1000uF 25V M
C971QETN1EM-107ZE CAPACITOR100uF 25V M
C972NCB31HK-104XC CAPACITOR0.1uF 50V K
C973QETN1AM-107ZE CAPACITOR100uF 10V M
C974QETN1AM-107ZE CAPACITOR100uF 10V M
C975QETN1AM-107ZE CAPACITOR100uF 10V M
C976QETN1EM-107ZE CAPACITOR100uF 25V M
C977QETN1AM-108ZE CAPACITOR1000uF 10V M
C981NRSA63J-0R0XMG RESISTOR0
C983QETN1CM-107ZE CAPACITOR100uF 16V M
C991QCZ9079-102C CAPACITOR1000pF AC250V M
C992QCZ9079-102C CAPACITOR1000pF AC250V M
C993QCZ9079-102C CAPACITOR1000pF AC250V M
C994QFLC1HJ-102ZM CAPACITOR1000pF 50V J
C001NCB31HK-103XC CAPACITOR0.01uF 50V K
C002QETN1HM-336ZE CAPACITOR33uF 50V M
C005NCB31HK-103XC CAPACITOR0.01uF 50V K
C006QETN1AM-477ZE CAPACITOR470uF 10V M
C007NCB31HK-103XC CAPACITOR0.01uF 50V K
C008QETN1HM-106ZE CAPACITOR10uF 50V M
C101NCB31HK-472XC CAPACITOR4700pF 50V K
C102QETN1EM-476ZE CAPACITOR47uF 25V M
C103NCB31HK-472XC CAPACITOR4700pF 50V K
C104NCB31HK-472XC CAPACITOR4700pF 50V K
C105NCB31HK-472XC CAPACITOR4700pF 50V K
C106NCB31HK-472XC CAPACITOR4700pF 50V K
C107NCB31HK-104XC CAPACITOR0.1uF 50V K
C108NCB31HK-103XC CAPACITOR0.01uF 50V K
C109QETN1CM-477ZE CAPACITOR470uF 16V M
C111NCB31CK-103XC CAPACITOR0.01uF 16V K
C112NCB31CK-103XC CAPACITOR0.01uF 16V K
C113NCB31CK-103XC CAPACITOR0.01uF 16V K
C351QFZ0097-103MM CAPACITOR0.01uF 1250V K
C352QETN1CM-477ZE CAPACITOR470uF 16V M
C354NDC31HJ-331XC CAPACITOR330pF 50V J
C355NDC31HJ-271XC CAPACITOR270pF 50V J
C356NDC31HJ-391XC CAPACITOR390pF 50V J
C357QETN1AM-477ZE CAPACITOR470uF 10V M
C422QCS32HJ-180ZC CAPACITOR18pF 500V J
C423NCB31HK-682XC CAPACITOR6800pF 50V K
C424QFLC2AJ-683ZM CAPACITOR0.068uF 100V J
C427QETM1HM-108E CAPACITOR1000uF 50V M
C428QETN1HM-227ZE CAPACITOR220uF 50V M
C430QFLC2AJ-563ZM CAPACITOR0.056uF 100V J
C431QFVF1HJ-184ZMF CAPACITOR0.18uF 50V J
C435NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C436NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C471QETN1HM-226ZE CAPACITOR22uF 50V M
C521QCB31HK-332ZC CAPACITOR3300pF 50V K
C522QFLC1HJ-223ZM CAPACITOR0.022uF 50V J
C523QETN1VM-476ZE CAPACITOR47uF 35V M
C525QFZ0196-143MPP CAPACITOR0.014uF 1.5kV H
C526QFZ0196-113MPP CAPACITOR0.011uF 1.5kV H
C527QFZ0197-404MPP CAPACITOR0.4uF 250V J
C528QFP32GJ-393PP CAPACITOR0.039uF 400V J
C529QENC2AM-225ZBP E CAPACITOR2.2uF 100V M
C530QCB32HK-561ZC CAPACITOR560pF 500V K
C531QEZ0195-475ZBP E CAPACITOR4.7uF 50V M
C532QETN2EM-106ZE CAPACITOR10uF 250V M
C533QFZ0197-105MPP CAPACITOR1uF 250V J
C542QFZ0197-823MPP CAPACITOR0.082uF 250V J
C551QCB32HK-561ZC CAPACITOR560pF 500V K
C552QCB32HK-561ZC CAPACITOR560pF 500V K
C553QETN1EM-108ZE CAPACITOR1000uF 25V M
C554QETN1EM-108ZE CAPACITOR1000uF 25V M
C555QFLC2AJ-103ZM CAPACITOR0.01uF 100V J
C571QEZ0203-107E CAPACITOR100uF 160V M
C572QETN1CM-107ZE CAPACITOR100uF 16V M
C573QETN1VM-476ZE CAPACITOR47uF 35V M
C581QFVF1HJ-104ZMF CAPACITOR0.1uF 50V J
C591QETN1VM-476ZE CAPACITOR47uF 35V M
C601QETN1CM-107ZE CAPACITOR100uF 16V M
C603QETN1HM-105ZE CAPACITOR1uF 50V M
C604QETN1HM-106ZE CAPACITOR10uF 50V M
C605QETN1HM-106ZE CAPACITOR10uF 50V M
C606QETN1HM-107ZE CAPACITOR100uF 50V M
C607QETN1HM-106ZE CAPACITOR10uF 50V M
C608NCB31CK-224XC CAPACITOR0.22uF 16V K
C609NCB31CK-224XC CAPACITOR0.22uF 16V K
C610QETN1HM-106ZE CAPACITOR10uF 50V M
C611QETN1CM-477ZE CAPACITOR470uF 16V M
C701QETN1CM-107ZE CAPACITOR100uF 16V M
C702NCB31HK-104XC CAPACITOR0.1uF 50V K
C710NCB31HK-103XC CAPACITOR0.01uF 50V K
C711NCB31HK-103XC CAPACITOR0.01uF 50V K
C712NDC31HJ-220XC CAPACITOR22pF 50V J
C713NDC31HJ-220XC CAPACITOR22pF 50V J
C714NCB31HK-103XC CAPACITOR0.01uF 50V K
C715QETN1CM-107ZE CAPACITOR100uF 16V M
C716NCB31HK-822XC CAPACITOR8200pF 50V K
C717QETN1HM-474ZE CAPACITOR0.47uF 50V M
C718QFLC2AJ-104ZM CAPACITOR0.1uF 100V J
C719QETN1HM-225ZE CAPACITOR2.2uF 50V M
(No.YA552)3-11
Page 49
Ref No. Part No.Part NameDescription Local
Ref No. Part No.Part NameDescription Local
C720NCB31HK-103XC CAPACITOR0.01uF 50V K
C721NCB31HK-103XC CAPACITOR0.01uF 50V K
C723NCB31HK-103XC CAPACITOR0.01uF 50V K
C724QETN1HM-106ZE CAPACITOR10uF 50V M
C725QENC1HM-105ZBP E CAPACITOR1uF 50V M
C726QETN1HM-106ZE CAPACITOR10uF 50V M
C727NCB31HK-104XC CAPACITOR0.1uF 50V K
C728NCB31HK-104XC CAPACITOR0.1uF 50V K
C729QETN1HM-106ZE CAPACITOR10uF 50V M
C730QETN1EM-476ZE CAPACITOR47uF 25V M
C731QETN1HM-474ZE CAPACITOR0.47uF 50V M
C732NCB31HK-102XC CAPACITOR1000pF 50V K
C733NCB31HK-103XC CAPACITOR0.01uF 50V K
C734QETN1HM-475ZE CAPACITOR4.7uF 50V M
C735QETN1HM-225ZE CAPACITOR2.2uF 50V M
C736NCB31HK-103XC CAPACITOR0.01uF 50V K
C737QETN1HM-105ZE CAPACITOR1uF 50V M
C738NCB31HK-222XC CAPACITOR2200pF 50V K
C739NCB31CK-224XC CAPACITOR0.22uF 16V K
C740QETN1CM-107ZE CAPACITOR100uF 16V M
C741NCB31HK-103XC CAPACITOR0.01uF 50V K
C743QETN1HM-106ZE CAPACITOR10uF 50V M
C744NCB31HK-103XC CAPACITOR0.01uF 50V K
C745QETN1CM-107ZE CAPACITOR100uF 16V M
C747NCB31HK-103XC CAPACITOR0.01uF 50V K
C748QETN1EM-476ZE CAPACITOR47uF 25V M
C754NDC21HJ-100XC CAPACITOR10pF 50V J
C755NCB31HK-104XC CAPACITOR0.1uF 50V K
C801QETN1HM-225ZE CAPACITOR2.2uF 50V M
C803QETN1HM-105ZE CAPACITOR1uF 50V M
C804QETN1HM-105ZE CAPACITOR1uF 50V M
C805QETN1HM-225ZE CAPACITOR2.2uF 50V M
C808QETN1AM-477ZE CAPACITOR470uF 10V M
C809QETN1HM-106ZE CAPACITOR10uF 50V M
C810QETN1HM-105ZE CAPACITOR1uF 50V M
C901QFZ9072-224MM CAPACITOR0.22uF AC250V K
C902QFZ9072-224MM CAPACITOR0.22uF AC250V K
C903QFZ9072-224MM CAPACITOR0.22uF AC250V K
C904QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C905QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C906QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C910QEZ0476-227E CAPACITOR220uF 400V M
C911QCZ0364-561C CAPACITOR560pF 2kV K
C912QETN1VM-226ZE CAPACITOR22uF 35V M
C913NCB31HK-103XC CAPACITOR0.01uF 50V K
C914NCB31HK-104XC CAPACITOR0.1uF 50V K
C915QFLC1HJ-471ZM CAPACITOR470pF 50V J
C918QCB32HK-103C CAPACITOR0.01uF 500V K
C951QCZ0364-102C CAPACITOR1000pF 2kV K
C952QCB32HK-471ZC CAPACITOR470pF 500V K
C953QCB32HK-471ZC CAPACITOR470pF 500V K
C954QCB32HK-471ZC CAPACITOR470pF 500V K
C955QCB32HK-471ZC CAPACITOR470pF 500V K
C961QEZ0203-107E CAPACITOR100uF 160V M
C963QETN1AM-108ZE CAPACITOR1000uF 10V M
C964QETN1EM-477ZE CAPACITOR470uF 25V M
C965QETN1VM-477ZE CAPACITOR470uF 35V M
C966QETN1EM-108ZE CAPACITOR1000uF 25V M
C971QETN1EM-107ZE CAPACITOR100uF 25V M
C972NCB31HK-104XC CAPACITOR0.1uF 50V K
C973QETN1AM-107ZE CAPACITOR100uF 10V M
C974QETN1AM-107ZE CAPACITOR100uF 10V M
C975QETN1AM-107ZE CAPACITOR100uF 10V M
C976QETN1EM-107ZE CAPACITOR100uF 25V M
C977QETN1AM-108ZE CAPACITOR1000uF 10V M
C981NRSA63J-0R0XMG RESISTOR0
C983QETN1CM-107ZE CAPACITOR100uF 16V M
C991QCZ9079-102C CAPACITOR1000pF AC250V M
C992QCZ9079-102C CAPACITOR1000pF AC250V M
C993QCZ9079-102C CAPACITOR1000pF AC250V M
C994QFLC1HJ-102ZM CAPACITOR1000pF 50V J
C001NCB31HK-103XC CAPACITOR0.01uF 50V K
C002QETN1HM-336ZE CAPACITOR33uF 50V M
C005NCB31HK-103XC CAPACITOR0.01uF 50V K
C006QETN1AM-477ZE CAPACITOR470uF 10V M
C007NCB31HK-103XC CAPACITOR0.01uF 50V K
C008QETN1HM-106ZE CAPACITOR10uF 50V M
C101NCB31HK-472XC CAPACITOR4700pF 50V K
C102QETN1EM-476ZE CAPACITOR47uF 25V M
C103NCB31HK-472XC CAPACITOR4700pF 50V K
C104NCB31HK-472XC CAPACITOR4700pF 50V K
C105NCB31HK-472XC CAPACITOR4700pF 50V K
C106NCB31HK-472XC CAPACITOR4700pF 50V K
C107NCB31HK-104XC CAPACITOR0.1uF 50V K
C108NCB31HK-103XC CAPACITOR0.01uF 50V K
C109QETN1CM-477ZE CAPACITOR470uF 16V M
C111NCB31CK-103XC CAPACITOR0.01uF 16V K
C112NCB31CK-103XC CAPACITOR0.01uF 16V K
C113NCB31CK-103XC CAPACITOR0.01uF 16V K
C351QFZ0097-103MM CAPACITOR0.01uF 1250V K
C352QETN1CM-477ZE CAPACITOR470uF 16V M
C354NDC31HJ-331XC CAPACITOR330pF 50V J
C355NDC31HJ-271XC CAPACITOR270pF 50V J
C356NDC31HJ-391XC CAPACITOR390pF 50V J
C357QETN1AM-477ZE CAPACITOR470uF 10V M
C422QCS32HJ-180ZC CAPACITOR18pF 500V J
C423NCB31HK-682XC CAPACITOR6800pF 50V K
C424QFLC2AJ-683ZM CAPACITOR0.068uF 100V J
C427QETM1HM-108E CAPACITOR1000uF 50V M
C428QETN1HM-227ZE CAPACITOR220uF 50V M
C430QFLC2AJ-563ZM CAPACITOR0.056uF 100V J
C431QFVF1HJ-184ZMF CAPACITOR0.18uF 50V J
C435NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C436NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C471QETN1HM-226ZE CAPACITOR22uF 50V M
C521QCB31HK-332ZC CAPACITOR3300pF 50V K
C522QFLC1HJ-223ZM CAPACITOR0.022uF 50V J
C523QETN1VM-476ZE CAPACITOR47uF 35V M
C525QFZ0196-143MPP CAPACITOR0.014uF 1.5kV H
C526QFZ0196-113MPP CAPACITOR0.011uF 1.5kV H
C527QFZ0197-404MPP CAPACITOR0.4uF 250V J
C528QFP32GJ-393PP CAPACITOR0.039uF 400V J
C529QENC2AM-225ZBP E CAPACITOR2.2uF 100V M
C530QCB32HK-561ZC CAPACITOR560pF 500V K
C531QEZ0195-475ZBP E CAPACITOR4.7uF 50V M
C532QETN2EM-106ZE CAPACITOR10uF 250V M
C533QFZ0197-105MPP CAPACITOR1uF 250V J
C542QFZ0197-823MPP CAPACITOR0.082uF 250V J
C551QCB32HK-561ZC CAPACITOR560pF 500V K
C552QCB32HK-561ZC CAPACITOR560pF 500V K
C553QETN1EM-108ZE CAPACITOR1000uF 25V M
C554QETN1EM-108ZE CAPACITOR1000uF 25V M
C555QFLC2AJ-103ZM CAPACITOR0.01uF 100V J
C571QEZ0203-107E CAPACITOR100uF 160V M
C572QETN1CM-107ZE CAPACITOR100uF 16V M
C573QETN1VM-476ZE CAPACITOR47uF 35V M
C581QFVF1HJ-104ZMF CAPACITOR0.1uF 50V J
C591QETN1VM-476ZE CAPACITOR47uF 35V M
C601QETN1CM-107ZE CAPACITOR100uF 16V M
C603QETN1HM-105ZE CAPACITOR1uF 50V M
C604QETN1HM-106ZE CAPACITOR10uF 50V M
C605QETN1HM-106ZE CAPACITOR10uF 50V M
C606QETN1HM-107ZE CAPACITOR100uF 50V M
C607QETN1HM-106ZE CAPACITOR10uF 50V M
C608NCB31CK-224XC CAPACITOR0.22uF 16V K
C609NCB31CK-224XC CAPACITOR0.22uF 16V K
C610QETN1HM-106ZE CAPACITOR10uF 50V M
C611QETN1CM-477ZE CAPACITOR470uF 16V M
C701QETN1CM-107ZE CAPACITOR100uF 16V M
C702NCB31HK-104XC CAPACITOR0.1uF 50V K
C710NCB31HK-103XC CAPACITOR0.01uF 50V K
C711NCB31HK-103XC CAPACITOR0.01uF 50V K
C712NDC31HJ-220XC CAPACITOR22pF 50V J
C713NDC31HJ-220XC CAPACITOR22pF 50V J
C714NCB31HK-103XC CAPACITOR0.01uF 50V K
C715QETN1CM-107ZE CAPACITOR100uF 16V M
C716NCB31HK-822XC CAPACITOR8200pF 50V K
C717QETN1HM-474ZE CAPACITOR0.47uF 50V M
C718QFLC2AJ-104ZM CAPACITOR0.1uF 100V J
C719QETN1HM-225ZE CAPACITOR2.2uF 50V M
3-14(No.YA552)
Page 52
Ref No. Part No.Part NameDescription Local
Ref No. Part No.Part NameDescription Local
C720NCB31HK-103XC CAPACITOR0.01uF 50V K
C721NCB31HK-103XC CAPACITOR0.01uF 50V K
C723NCB31HK-103XC CAPACITOR0.01uF 50V K
C724QETN1HM-106ZE CAPACITOR10uF 50V M
C725QENC1HM-105ZBP E CAPACITOR1uF 50V M
C726QETN1HM-106ZE CAPACITOR10uF 50V M
C727NCB31HK-104XC CAPACITOR0.1uF 50V K
C728NCB31HK-104XC CAPACITOR0.1uF 50V K
C729QETN1HM-106ZE CAPACITOR10uF 50V M
C730QETN1EM-476ZE CAPACITOR47uF 25V M
C731QETN1HM-474ZE CAPACITOR0.47uF 50V M
C732NCB31HK-102XC CAPACITOR1000pF 50V K
C733NCB31HK-103XC CAPACITOR0.01uF 50V K
C734QETN1HM-475ZE CAPACITOR4.7uF 50V M
C735QETN1HM-225ZE CAPACITOR2.2uF 50V M
C736NCB31HK-103XC CAPACITOR0.01uF 50V K
C737QETN1HM-105ZE CAPACITOR1uF 50V M
C738NCB31HK-222XC CAPACITOR2200pF 50V K
C739NCB31CK-224XC CAPACITOR0.22uF 16V K
C740QETN1CM-107ZE CAPACITOR100uF 16V M
C741NCB31HK-103XC CAPACITOR0.01uF 50V K
C743QETN1HM-106ZE CAPACITOR10uF 50V M
C744NCB31HK-103XC CAPACITOR0.01uF 50V K
C745QETN1CM-107ZE CAPACITOR100uF 16V M
C747NCB31HK-103XC CAPACITOR0.01uF 50V K
C748QETN1EM-476ZE CAPACITOR47uF 25V M
C754NDC21HJ-100XC CAPACITOR10pF 50V J
C755NCB31HK-104XC CAPACITOR0.1uF 50V K
C801QETN1HM-225ZE CAPACITOR2.2uF 50V M
C803QETN1HM-105ZE CAPACITOR1uF 50V M
C804QETN1HM-105ZE CAPACITOR1uF 50V M
C805QETN1HM-225ZE CAPACITOR2.2uF 50V M
C808QETN1AM-477ZE CAPACITOR470uF 10V M
C809QETN1HM-106ZE CAPACITOR10uF 50V M
C810QETN1HM-105ZE CAPACITOR1uF 50V M
C901QFZ9072-224MM CAPACITOR0.22uF AC250V K
C902QFZ9072-224MM CAPACITOR0.22uF AC250V K
C903QFZ9072-224MM CAPACITOR0.22uF AC250V K
C904QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C905QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C906QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C910QEZ0476-227E CAPACITOR220uF 400V M
C911QCZ0364-561C CAPACITOR560pF 2kV K
C912QETN1VM-226ZE CAPACITOR22uF 35V M
C913NCB31HK-103XC CAPACITOR0.01uF 50V K
C914NCB31HK-104XC CAPACITOR0.1uF 50V K
C915QFLC1HJ-471ZM CAPACITOR470pF 50V J
C918QCB32HK-103C CAPACITOR0.01uF 500V K
C951QCZ0364-102C CAPACITOR1000pF 2kV K
C952QCB32HK-471ZC CAPACITOR470pF 500V K
C953QCB32HK-471ZC CAPACITOR470pF 500V K
C954QCB32HK-471ZC CAPACITOR470pF 500V K
C955QCB32HK-471ZC CAPACITOR470pF 500V K
C961QEZ0203-107E CAPACITOR100uF 160V M
C963QETN1AM-108ZE CAPACITOR1000uF 10V M
C964QETN1EM-477ZE CAPACITOR470uF 25V M
C965QETN1VM-477ZE CAPACITOR470uF 35V M
C966QETN1EM-108ZE CAPACITOR1000uF 25V M
C971QETN1EM-107ZE CAPACITOR100uF 25V M
C972NCB31HK-104XC CAPACITOR0.1uF 50V K
C973QETN1AM-107ZE CAPACITOR100uF 10V M
C974QETN1AM-107ZE CAPACITOR100uF 10V M
C975QETN1AM-107ZE CAPACITOR100uF 10V M
C976QETN1EM-107ZE CAPACITOR100uF 25V M
C977QETN1AM-108ZE CAPACITOR1000uF 10V M
C981NRSA63J-0R0XMG RESISTOR0
C983QETN1CM-107ZE CAPACITOR100uF 16V M
C991QCZ9079-102C CAPACITOR1000pF AC250V M
C992QCZ9079-102C CAPACITOR1000pF AC250V M
C993QCZ9079-102C CAPACITOR1000pF AC250V M
C994QFLC1HJ-102ZM CAPACITOR1000pF 50V J
C001NCB31HK-103XC CAPACITOR0.01uF 50V K
C002QETN1HM-336ZE CAPACITOR33uF 50V M
C005NCB31HK-103XC CAPACITOR0.01uF 50V K
C006QETN1AM-477ZE CAPACITOR470uF 10V M
C007NCB31HK-103XC CAPACITOR0.01uF 50V K
C008QETN1HM-106ZE CAPACITOR10uF 50V M
C101NCB31HK-472XC CAPACITOR4700pF 50V K
C102QETN1EM-476ZE CAPACITOR47uF 25V M
C103NCB31HK-472XC CAPACITOR4700pF 50V K
C104NCB31HK-472XC CAPACITOR4700pF 50V K
C105NCB31HK-472XC CAPACITOR4700pF 50V K
C106NCB31HK-472XC CAPACITOR4700pF 50V K
C107NCB31HK-104XC CAPACITOR0.1uF 50V K
C108NCB31HK-103XC CAPACITOR0.01uF 50V K
C109QETN1CM-477ZE CAPACITOR470uF 16V M
C111NCB31CK-103XC CAPACITOR0.01uF 16V K
C112NCB31CK-103XC CAPACITOR0.01uF 16V K
C113NCB31CK-103XC CAPACITOR0.01uF 16V K
C351QFZ0097-103MM CAPACITOR0.01uF 1250V K
C352QETN1CM-477ZE CAPACITOR470uF 16V M
C354NDC31HJ-331XC CAPACITOR330pF 50V J
C355NDC31HJ-271XC CAPACITOR270pF 50V J
C356NDC31HJ-391XC CAPACITOR390pF 50V J
C357QETN1AM-477ZE CAPACITOR470uF 10V M
C422QCS32HJ-180ZC CAPACITOR18pF 500V J
C423NCB31HK-682XC CAPACITOR6800pF 50V K
C424QFLC2AJ-683ZM CAPACITOR0.068uF 100V J
C427QETM1HM-108E CAPACITOR1000uF 50V M
C428QETN1HM-227ZE CAPACITOR220uF 50V M
C430QFLC2AJ-563ZM CAPACITOR0.056uF 100V J
C431QFVF1HJ-184ZMF CAPACITOR0.18uF 50V J
C435NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C436NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C471QETN1HM-226ZE CAPACITOR22uF 50V M
C521QCB31HK-332ZC CAPACITOR3300pF 50V K
C522QFLC1HJ-223ZM CAPACITOR0.022uF 50V J
C523QETN1VM-476ZE CAPACITOR47uF 35V M
C525QFZ0196-143MPP CAPACITOR0.014uF 1.5kV H
C526QFZ0196-113MPP CAPACITOR0.011uF 1.5kV H
C527QFZ0197-404MPP CAPACITOR0.4uF 250V J
C528QFP32GJ-393PP CAPACITOR0.039uF 400V J
C529QENC2AM-225ZBP E CAPACITOR2.2uF 100V M
C530QCB32HK-561ZC CAPACITOR560pF 500V K
C531QEZ0195-475ZBP E CAPACITOR4.7uF 50V M
C532QETN2EM-106ZE CAPACITOR10uF 250V M
C533QFZ0197-105MPP CAPACITOR1uF 250V J
C542QFZ0197-823MPP CAPACITOR0.082uF 250V J
C551QCB32HK-561ZC CAPACITOR560pF 500V K
C552QCB32HK-561ZC CAPACITOR560pF 500V K
C553QETN1EM-108ZE CAPACITOR1000uF 25V M
C554QETN1EM-108ZE CAPACITOR1000uF 25V M
C555QFLC2AJ-103ZM CAPACITOR0.01uF 100V J
C571QEZ0203-107E CAPACITOR100uF 160V M
C572QETN1CM-107ZE CAPACITOR100uF 16V M
C573QETN1VM-476ZE CAPACITOR47uF 35V M
C581QFVF1HJ-104ZMF CAPACITOR0.1uF 50V J
C591QETN1VM-476ZE CAPACITOR47uF 35V M
C601QETN1CM-107ZE CAPACITOR100uF 16V M
C603QETN1HM-105ZE CAPACITOR1uF 50V M
C604QETN1HM-106ZE CAPACITOR10uF 50V M
C605QETN1HM-106ZE CAPACITOR10uF 50V M
C606QETN1HM-107ZE CAPACITOR100uF 50V M
C607QETN1HM-106ZE CAPACITOR10uF 50V M
C608NCB31CK-224XC CAPACITOR0.22uF 16V K
C609NCB31CK-224XC CAPACITOR0.22uF 16V K
C610QETN1HM-106ZE CAPACITOR10uF 50V M
C611QETN1CM-477ZE CAPACITOR470uF 16V M
C701QETN1CM-107ZE CAPACITOR100uF 16V M
C702NCB31HK-104XC CAPACITOR0.1uF 50V K
C710NCB31HK-103XC CAPACITOR0.01uF 50V K
C711NCB31HK-103XC CAPACITOR0.01uF 50V K
C712NDC31HJ-220XC CAPACITOR22pF 50V J
C713NDC31HJ-220XC CAPACITOR22pF 50V J
C714NCB31HK-103XC CAPACITOR0.01uF 50V K
C715QETN1CM-107ZE CAPACITOR100uF 16V M
C716NCB31HK-822XC CAPACITOR8200pF 50V K
C717QETN1HM-474ZE CAPACITOR0.47uF 50V M
C718QFLC2AJ-104ZM CAPACITOR0.1uF 100V J
C719QETN1HM-225ZE CAPACITOR2.2uF 50V M
[AV-21QMG7/G,AV-21QMG7B/G]
(No.YA552)3-17
Page 55
Ref No. Part No.Part NameDescription Local
Ref No. Part No.Part NameDescription Local
C720NCB31HK-103XC CAPACITOR0.01uF 50V K
C721NCB31HK-103XC CAPACITOR0.01uF 50V K
C723NCB31HK-103XC CAPACITOR0.01uF 50V K
C724QETN1HM-106ZE CAPACITOR10uF 50V M
C725QENC1HM-105ZBP E CAPACITOR1uF 50V M
C726QETN1HM-106ZE CAPACITOR10uF 50V M
C727NCB31HK-104XC CAPACITOR0.1uF 50V K
C728NCB31HK-104XC CAPACITOR0.1uF 50V K
C729QETN1HM-106ZE CAPACITOR10uF 50V M
C730QETN1EM-476ZE CAPACITOR47uF 25V M
C731QETN1HM-474ZE CAPACITOR0.47uF 50V M
C732NCB31HK-102XC CAPACITOR1000pF 50V K
C733NCB31HK-103XC CAPACITOR0.01uF 50V K
C734QETN1HM-475ZE CAPACITOR4.7uF 50V M
C735QETN1HM-225ZE CAPACITOR2.2uF 50V M
C736NCB31HK-103XC CAPACITOR0.01uF 50V K
C737QETN1HM-105ZE CAPACITOR1uF 50V M
C738NCB31HK-222XC CAPACITOR2200pF 50V K
C739NCB31CK-224XC CAPACITOR0.22uF 16V K
C740QETN1CM-107ZE CAPACITOR100uF 16V M
C741NCB31HK-103XC CAPACITOR0.01uF 50V K
C743QETN1HM-106ZE CAPACITOR10uF 50V M
C744NCB31HK-103XC CAPACITOR0.01uF 50V K
C745QETN1CM-107ZE CAPACITOR100uF 16V M
C747NCB31HK-103XC CAPACITOR0.01uF 50V K
C748QETN1EM-476ZE CAPACITOR47uF 25V M
C754NDC31HJ-100XC CAPACITOR10pF 50V J
C755NCB31HK-104XC CAPACITOR0.1uF 50V K
C801QETN1HM-225ZE CAPACITOR2.2uF 50V M
C803QETN1HM-105ZE CAPACITOR1uF 50V M
C804QETN1HM-105ZE CAPACITOR1uF 50V M
C805QETN1HM-225ZE CAPACITOR2.2uF 50V M
C808QETN1AM-477ZE CAPACITOR470uF 10V M
C809QETN1HM-106ZE CAPACITOR10uF 50V M
C810QETN1HM-105ZE CAPACITOR1uF 50V M
C901QFZ9072-224MM CAPACITOR0.22uF AC250V K
C902QFZ9072-224MM CAPACITOR0.22uF AC250V K
C903QFZ9072-224MM CAPACITOR0.22uF AC250V K
C904QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C905QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C906QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C910QEZ0476-227E CAPACITOR220uF 400V M
C911QCZ0364-561C CAPACITOR560pF 2kV K
C912QETN1VM-226ZE CAPACITOR22uF 35V M
C913NCB31HK-103XC CAPACITOR0.01uF 50V K
C914NCB31HK-104XC CAPACITOR0.1uF 50V K
C915QFLC1HJ-471ZM CAPACITOR470pF 50V J
C918QCB32HK-103C CAPACITOR0.01uF 500V K
C951QCZ0364-102C CAPACITOR1000pF 2kV K
C952QCB32HK-471ZC CAPACITOR470pF 500V K
C953QCB32HK-471ZC CAPACITOR470pF 500V K
C954QCB32HK-471ZC CAPACITOR470pF 500V K
C955QCB32HK-471ZC CAPACITOR470pF 500V K
C961QEZ0203-107E CAPACITOR100uF 160V M
C963QETN1AM-108ZE CAPACITOR1000uF 10V M
C964QETN1EM-477ZE CAPACITOR470uF 25V M
C965QETN1VM-477ZE CAPACITOR470uF 35V M
C966QETN1EM-108ZE CAPACITOR1000uF 25V M
C971QETN1EM-107ZE CAPACITOR100uF 25V M
C972NCB31HK-104XC CAPACITOR0.1uF 50V K
C973QETN1AM-107ZE CAPACITOR100uF 10V M
C974QETN1AM-107ZE CAPACITOR100uF 10V M
C975QETN1AM-107ZE CAPACITOR100uF 10V M
C976QETN1EM-107ZE CAPACITOR100uF 25V M
C977QETN1AM-108ZE CAPACITOR1000uF 10V M
C981NRSA63J-0R0XMG RESISTOR0
C983QETN1CM-107ZE CAPACITOR100uF 16V M
C991QCZ9079-102C CAPACITOR1000pF AC250V M
C992QCZ9079-102C CAPACITOR1000pF AC250V M
C993QCZ9079-102C CAPACITOR1000pF AC250V M
C994QFLC1HJ-102ZM CAPACITOR1000pF 50V J
1GG10285-017B-HPACKING CASEAV-2100QE,AV-21Q17,AV-21Q17L,AV-21QMG7S
1GG10282-047B-HPACKING CASEAV-21QMG7G,AV-21QMG7BG
2GG10483-001A-HCUSHION ASSY4pcs in 1set
3GG30097-003B-HPOLY BAG
4GG30096-001B-HPOLY BAG
5------------BATTERYAA/R6(x2)
AV-2100QE/KSK and AV-2100QE/NSK are the models whose production place and destination were
changed from that of AV-2100QE.
Therefore, this service manual describes only the items which differ from those of the AV-2100QE service
manual.
For details other than those described in this manual, please refer to the AV-2100QE service manual
(No.YA552
, 2007/9).
HOW TO IDENTIFY MODELS
Distinguish name is added at the bottom of the rating label.
C001NCB31HK-103XC CAPACITOR0.01uF 50V K
C002QETN1HM-336ZE CAPACITOR33uF 50V M
C005NCB31HK-103XC CAPACITOR0.01uF 50V K
C006QETN1AM-477ZE CAPACITOR470uF 10V M
C007NCB31HK-103XC CAPACITOR0.01uF 50V K
C008QETN1HM-106ZE CAPACITOR10uF 50V M
C101NCB31HK-472XC CAPACITOR4700pF 50V K
C102QETN1EM-476ZE CAPACITOR47uF 25V M
C103NCB31HK-472XC CAPACITOR4700pF 50V K
C104NCB31HK-472XC CAPACITOR4700pF 50V K
C105NCB31HK-472XC CAPACITOR4700pF 50V K
C106NCB31HK-472XC CAPACITOR4700pF 50V K
C107NCB31HK-104XC CAPACITOR0.1uF 50V K
C108NCB31HK-103XC CAPACITOR0.01uF 50V K
C109QETN1CM-477ZE CAPACITOR470uF 16V M
C422QCS32HJ-180ZC CAPACITOR18pF 500V J
C423NCB31HK-682XC CAPACITOR6800pF 50V K
C424QFLC2AJ-683ZM CAPACITOR0.068uF 100V J
C427QETM1HM-108E CAPACITOR1000uF 50V M
C428QETN1HM-227ZE CAPACITOR220uF 50V M
C430QFLC2AJ-563ZM CAPACITOR0.056uF 100V J
C431QFVF1HJ-184ZMF CAPACITOR0.18uF 50V J
C435NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C436NCF21HZ-334XC CAPACITOR0.33uF 50V Z
C471QETN1HM-226ZE CAPACITOR22uF 50V M
C521QCB31HK-332ZC CAPACITOR3300pF 50V K
C522QFLC1HJ-223ZM CAPACITOR0.022uF 50V J
C523QETN1VM-476ZE CAPACITOR47uF 35V M
C525QFZ0196-103MPP CAPACITOR0.01uF 1.5kV H
C526QFZ0196-143MPP CAPACITOR0.014uF 1.5kV H
C527QFZ0197-564MPP CAPACITOR0.56uF 250V J
C528QFP32GJ-273PP CAPACITOR0.027uF 400V J
C529QENC2AM-225ZBP E CAPACITOR2.2uF 100V M
C530QCB32HK-561ZC CAPACITOR560pF 500V K
C531QEZ0195-475ZBP E CAPACITOR4.7uF 50V M
C532QETN2EM-106ZE CAPACITOR10uF 250V M
C533QFZ0197-684MPP CAPACITOR0.68uF 250V J
C542QFZ0197-823MPP CAPACITOR0.082uF 250V J
C551QCB32HK-561ZC CAPACITOR560pF 500V K
C552QCB32HK-561ZC CAPACITOR560pF 500V K
C553QETN1EM-108ZE CAPACITOR1000uF 25V M
C554QETN1EM-108ZE CAPACITOR1000uF 25V M
C555QFLC2AJ-103ZM CAPACITOR0.01uF 100V J
C571QEZ0203-107E CAPACITOR100uF 160V M
C572QETN1CM-107ZE CAPACITOR100uF 16V M
C573QETN1VM-476ZE CAPACITOR47uF 35V M
C581QFVF1HJ-104ZMF CAPACITOR0.1uF 50V J
C591QETN1VM-476ZE CAPACITOR47uF 35V M
C601QETN1CM-107ZE CAPACITOR100uF 16V M
C603QETN1HM-105ZE CAPACITOR1uF 50V M
C604QETN1HM-106ZE CAPACITOR10uF 50V M
C605QETN1HM-106ZE CAPACITOR10uF 50V M
C606QETN1HM-107ZE CAPACITOR100uF 50V M
C607QETN1HM-106ZE CAPACITOR10uF 50V M
C608NCB31CK-224XC CAPACITOR0.22uF 16V K
C609NCB31CK-224XC CAPACITOR0.22uF 16V K
C610QETN1HM-106ZE CAPACITOR10uF 50V M
C611QETN1CM-477ZE CAPACITOR470uF 16V M
C701QETN1CM-107ZE CAPACITOR100uF 16V M
C702NCB31HK-104XC CAPACITOR0.1uF 50V K
C710NCB31HK-103XC CAPACITOR0.01uF 50V K
C711NCB31HK-103XC CAPACITOR0.01uF 50V K
C712NDC31HJ-220XC CAPACITOR22pF 50V J
C713NDC31HJ-220XC CAPACITOR22pF 50V J
C714NCB31HK-103XC CAPACITOR0.01uF 50V K
C715QETN1CM-107ZE CAPACITOR100uF 16V M
C716NCB31HK-822XC CAPACITOR8200pF 50V K
C717QETN1HM-474ZE CAPACITOR0.47uF 50V M
C718QFLC2AJ-104ZM CAPACITOR0.1uF 100V J
C719QETN1HM-225ZE CAPACITOR2.2uF 50V M
C720NCB31HK-103XC CAPACITOR0.01uF 50V K
C721NCB31HK-103XC CAPACITOR0.01uF 50V K
C723NCB31HK-103XC CAPACITOR0.01uF 50V K
C724QETN1HM-106ZE CAPACITOR10uF 50V M
C725QENC1HM-105ZBP E CAPACITOR1uF 50V M
C726QETN1HM-106ZE CAPACITOR10uF 50V M
C727NCB31HK-104XC CAPACITOR0.1uF 50V K
C728NCB31HK-104XC CAPACITOR0.1uF 50V K
C729QETN1HM-106ZE CAPACITOR10uF 50V M
(No.YA552B)1-3
Page 61
Ref No.Part No.Part NameDescription Local
Ref No.Part No.Part NameDescription Local
C730QETN1EM-476ZE CAPACITOR47uF 25V M
C731QETN1HM-474ZE CAPACITOR0.47uF 50V M
C732NCB31HK-102XC CAPACITOR1000pF 50V K
C733NCB31HK-103XC CAPACITOR0.01uF 50V K
C734QETN1HM-475ZE CAPACITOR4.7uF 50V M
C735QETN1HM-225ZE CAPACITOR2.2uF 50V M
C736NCB31HK-103XC CAPACITOR0.01uF 50V K
C737QETN1HM-105ZE CAPACITOR1uF 50V M
C738NCB31HK-222XC CAPACITOR2200pF 50V K
C739NCB31CK-224XC CAPACITOR0.22uF 16V K
C740QETN1CM-107ZE CAPACITOR100uF 16V M
C741NCB31HK-103XC CAPACITOR0.01uF 50V K
C743QETN1HM-106ZE CAPACITOR10uF 50V M
C744NCB31HK-103XC CAPACITOR0.01uF 50V K
C745QETN1CM-107ZE CAPACITOR100uF 16V M
C747NCB31HK-103XC CAPACITOR0.01uF 50V K
C748QETN1EM-476ZE CAPACITOR47uF 25V M
C754NDC21HJ-100XC CAPACITOR10pF 50V J
C755NCB31HK-104XC CAPACITOR0.1uF 50V K
C801QETN1HM-225ZE CAPACITOR2.2uF 50V M
C803QETN1HM-105ZE CAPACITOR1uF 50V M
C804QETN1HM-105ZE CAPACITOR1uF 50V M
C805QETN1HM-225ZE CAPACITOR2.2uF 50V M
C808QETN1AM-477ZE CAPACITOR470uF 10V M
C809QETN1HM-106ZE CAPACITOR10uF 50V M
C810QETN1HM-105ZE CAPACITOR1uF 50V M
C901QFZ9072-224MM CAPACITOR0.22uF AC250V K
C902QFZ9072-224MM CAPACITOR0.22uF AC250V K
C903QFZ9072-224MM CAPACITOR0.22uF AC250V K
C904QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C905QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C906QCZ9015-102ZC CAPACITOR1000pF AC250V Z
C910QEZ0633-227E CAPACITOR220uF 450V M
C911QCZ0364-561C CAPACITOR560pF 2kV K
C912QETN1VM-226ZE CAPACITOR22uF 35V M
C913NCB31HK-103XC CAPACITOR0.01uF 50V K
C914NCB31HK-104XC CAPACITOR0.1uF 50V K
C915QFLC1HJ-471ZM CAPACITOR470pF 50V J
C918QCB32HK-103C CAPACITOR0.01uF 500V K
C951QCZ0364-102C CAPACITOR1000pF 2kV K
C952QCB32HK-471ZC CAPACITOR470pF 500V K
C953QCB32HK-471ZC CAPACITOR470pF 500V K
C954QCB32HK-471ZC CAPACITOR470pF 500V K
C955QCB32HK-471ZC CAPACITOR470pF 500V K
C961QEZ0203-107E CAPACITOR100uF 160V M
C963QETN1AM-108ZE CAPACITOR1000uF 10V M
C964QETN1EM-477ZE CAPACITOR470uF 25V M
C965QETN1VM-477ZE CAPACITOR470uF 35V M
C966QETN1EM-108ZE CAPACITOR1000uF 25V M
C971QETN1EM-107ZE CAPACITOR100uF 25V M
C972NCB31HK-104XC CAPACITOR0.1uF 50V K
C973QETN1AM-107ZE CAPACITOR100uF 10V M
C974QETN1AM-107ZE CAPACITOR100uF 10V M
C975QETN1AM-107ZE CAPACITOR100uF 10V M
C976QETN1EM-107ZE CAPACITOR100uF 25V M
C977QETN1HM-106ZE CAPACITOR10uF 50V M
C981NRSA63J-0R0XMG RESISTOR0
C983QETN1CM-107ZE CAPACITOR100uF 16V M
C991QCZ9079-102C CAPACITOR1000pF AC250V M
C992QCZ9079-102C CAPACITOR1000pF AC250V M
C993QCZ9079-102C CAPACITOR1000pF AC250V M
C994QFLC1HJ-102ZM CAPACITOR1000pF 50V J
Please be informed that there are errors in the following service manuals.
AV-2100QE, AV-21Q17,AV-21Q17/L, AV-21QMG7/G, AV-21QMG7/S, AV-21QMG7B/G (No.YA552
AV-2100QE/KSK, AV-2100QE/NSK (No.YA552B
AV-2100QE/B, AV-2100QE/KBSK, AV-21Q17/B, AV-21Q17/LB, AV-21QMG7/GB (No.YA552C
, 2007/10)
CORRECTION ITEM
PRINTED WIRING BOARD PARTS LIST
MAIN P.W. BOARD ASS'Y (Page 3-5)
Ref. No.
IC702ATE08-14UMG7ATE08-21QMG7IC(SERVICE)
INCORRECTCORRECT
Part No.
PRINTED WIRING BOARD PARTS LIST [AV-21Q17, AV-21Q17/B]