jvc AV-21D116-B Service Manual

SERVICE MANUAL
COLOUR TELEVISION
YA39620067
AV-21D116/B
BASIC CHASSIS
CG4
TABLE OF CONTENTS
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
COPYRIGHT © 2006 Victor Company of Japan, Limited
No.YA396
2006/7
SPECIFICATION
Items Contents
Dimensions (W × H × D) 59.8 cm × 46.8 cm × 47.8 cm
Mass 21 kg
TV RF System B/G, I, D/K
Colour System PAL
SECAM NTSC 3.58 / NTSC 4.43
Receiving Frequency
Intermediate Frequency VIF 38.0 MHz (B/G, I, D/K)
Colour Sub Carrier PAL
Power Input AC220 V to AC240 V, 50 Hz / 60 Hz
Power Consumption 90 W (Max) / 60 W(Avg)
Picture Tube Visible size: 52.8 cm measured diagonally
High Voltage 26.5 kV±1.5kV (at zero beam current)
Speaker 5 cm × 12 cm, Oval type × 2
Audio Power Output 3 W (monaural)
Aerial Input Terminal 75 unbalanced, coaxial
Input Terminal [Front / Rear]
Output Terminal [Rear]
Headphone Jack 3.5 mm mini jack × 1 Remote Control Unit RM-C1121 (Battery size : AA / R6 / UM-3 × 2)
VHF Low
VHF High
SECAM
46.25 MHz to 168.25 MHz
175.25 MHz to 463.25 MHz
UHF
471.25 MHz to 863.25 MHz
CATV
Mid (X to Z+2, S1 to S10) / Super (S11 to S20) / Hyper (S21 to S41) bands
SIF 32.5 MHz (5.5 MHz: B/G)
32MHz (6.0 MHz: I)
31.5MHz (6.5 MHz: D/K)
4.43 MHz
4.40625 MHz / 4.25 MHz
NTSC
3.58 MHz / 4.43 MHz
( H : 42.0 cm × V : 32.0 cm)
Video
1 V(p-p), 75 , RCA pin jack × 2
Audio
500 mV(rms) (-4 dBs), High impedance, RCA pin jack × 2
Video
1 V(p-p), 75, RCA pin jack × 1
Audio
500 mV(rms) (-4 dBs), Low impedance, RCA pin jack × 1
Design and specifications are subject to change without notice.
1-2 (No.YA396)
SECTION 1
PRECAUTION
1.1 SAFETY PRECAUTIONS
(1) The design of this product contains special hardware,
many circuits and components specially for safety purposes. For continued protection, no changes should be made to the original design unless authorized in writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Service should be performed by qualified personnel only.
(2) Alterations of the design or circuitry of the products should
not be made. Any design alterations or additions will void the manufacturer's warranty and will further relieve the manufacturer of responsibility for personal injury or property damage resulting therefrom.
(3) Many electrical and mechanical parts in the products have
special safety-related characteristics. These characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in the parts list of Service manual. Electrical components
having such features are identified by shading on the schematics and by ( ) on the parts list in Service manual. The use of a substitute replacement which does
not have the same safety characteristics as the recommended replacement part shown in the parts list of Service manual may cause shock, fire, or other hazards.
(4) Don't short between the LIVE side ground and
ISOLATED (NEUTRAL) side ground or EARTH side ground when repairing.
Some model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND, the ISOLATED (NEUTRAL) : ( ) side GND and EARTH : ( ) side GND. Don't short between the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND and never measure the LIVE side GND and ISOLATED (NEUTRAL) side GND or EARTH side GND at the same time with a measuring apparatus (oscilloscope etc.). If above note will not be kept, a fuse or any parts will be broken.
(5) If any repair has been made to the chassis, it is
recommended that the B1 setting should be checked or adjusted (See ADJUSTMENT OF B1 POWER SUPPLY).
(6) The high voltage applied to the picture tube must conform
with that specified in Service manual. Excessive high voltage can cause an increase in X-Ray emission, arcing and possible component damage, therefore operation under excessive high voltage conditions should be kept to a minimum, or should be prevented. If severe arcing occurs, remove the AC power immediately and determine the cause by visual inspection (incorrect installation, cracked or melted high voltage harness, poor soldering, etc.). To maintain the proper minimum level of soft X-Ray emission, components in the high voltage circuitry including the picture tube must be the exact replacements or alternatives approved by the manufacturer of the complete product.
(7) Do not check high voltage by drawing an arc. Use a high
voltage meter or a high voltage probe with a VTVM. Discharge the picture tube before attempting meter connection, by connecting a clip lead to the ground frame
and connecting the other end of the lead through a 10k
2W resistor to the anode button.
(8) When service is required, observe the original lead dress.
Extra precaution should be given to assure correct lead dress in the high voltage circuit area. Where a short circuit has occurred, those components that indicate evidence of overheating should be replaced. Always use the manufacturer's replacement components.
(9) Isolation Check (Safety for Electrical Shock Hazard)
After re-assembling the product, always perform an isolation check on the exposed metal parts of the cabinet (antenna terminals, video/audio input and output terminals, Control knobs, metal cabinet, screw heads, earphone jack, control shafts, etc.) to be sure the product is safe to operate without danger of electrical shock.
a) Dielectric Strength Test
The isolation between the AC primary circuit and all metal parts exposed to the user, particularly any exposed metal part having a return path to the chassis should withstand a voltage of 3000V AC (r.m.s.) for a period of one second. (. . . . Withstand a voltage of 1100V AC (r.m.s.) to an appliance rated up to 120V, and 3000V AC (r.m.s.) to an appliance rated 200V or more, for a period of one second.) This method of test requires a test equipment not generally found in the service trade.
b) Leakage Current Check
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Using a "Leakage Current Tester", measure the leakage current from each exposed metal part of the cabinet, particularly any exposed metal part having a return path to the chassis, to a known good earth ground (water pipe, etc.). Any leakage current must not exceed 0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.2mA AC (r.m.s.).
Alternate Check Method
Plug the AC line cord directly into the AC outlet (do not use a line isolation transformer during this check.). Use
an AC voltmeter having 1000 per volt or more sensitivity in the following manner. Connect a 1500 10W resistor paralleled by a 0.15µF AC-type capacitor
between an exposed metal part and a known good earth ground (water pipe, etc.). Measure the AC voltage across the resistor with the AC voltmeter. Move the resistor connection to each exposed metal part, particularly any exposed metal part having a return path to the chassis, and measure the AC voltage across the resistor. Now, reverse the plug in the AC outlet and repeat each measurement. Any voltage measured must not exceed 0.75V AC (r.m.s.). This corresponds to
0.5mA AC (r.m.s.). However, in tropical area, this must not exceed 0.3V AC (r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
AC VOLTMETER (HAVING 1000 /V, OR MORE SENSITIVITY)
0.15 F AC-TYPE
PLACE THIS PROBE
1500 10W
GOOD EARTH GROUND
ON EACH EXPOSED ME TAL PAR T
(No.YA396)1-3
SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1 FEATURES
PICTURE MODE
This function can adjust the picture settings automatically. There are BRIGHT, STANDARD and SOFT in the PICTURE MODE.
RETURN +
This function can set a channel you frequently view to the Return Channel and you can view that channel at any time with one-touch.
2.2 TECHNINAL INFORMATION
2.2.1 MAIN MI-COM (CPU) PIN FUNCTION
Pin No.
Pin name I/O Function
1 REMOCON I Remote control 22 PROTECT I Low B protect detection [Detect: H]
2 SDA2 I/O Data for Inter IC control (For main memory) 23 P_ON/OFF I Main power control [ON : H]
3 SCL2 O Clock for Inter IC contorl (For main memory) 24 LOCK - Not used
4 BUS_FREE - Not used 25 3.58/OTH - Not used
5 NC - Not used 26 4.5/OTH - Not used
6 KEY1 I Key scan for front key (Menu CH -/+) 27 H_SYNC I Horizontal sync
7 KEY2 I Key scan for front key (Vol -/+) 28 I/II - Not used
8 ECO IN - Not used 29 OSD_Ys O Ys (blanking) for OSD
9 AFT I AFT voltage for tuner 30 OSD_B O Blue for OSD
10 LED[POW] - Not used 31 OSD_G O Green for OSD
11 LED[TIM] O Liting for timer [Liting : H] 32 OSD_R O Red for OSD
12 GND - GND 33 NC - Not used
13 NC - Not used 34 RST I CPU reset [Reset:L]
14 NC - Not used 35 V_SYNC I Vertical sync
15 TV/V - Not used 36 TCLOCK - Not used
16 TEXT RESET - Not used 37 SDA1 I/O Data for Inter IC control (For generally)
17 ACL ON/OFF - Not used 38 SCL1 O Clock for Inter IC contorl (For generally)
18 VOL O Volume control 39 VDD I 3.3V
19 A_MUTE O Aodio muting [Muting : H] 40 OSC1 I System clock oscillation (4MHz)
20 NC - Not used 41 OSC2 O System clock oscillation (4MHz)
21 TEXT/OTH - Not used 42 VSS - GND
CHILD LOCK
Use this function to prevent children from operating the TV without parental consent.
VNR
This function can reduce the picture noise.
Pin No.
Pin name I/O Function
1-4 (No.YA396)
SECTION 3
DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE
3.1.1 REMOVING THE REAR COVER
• Unplug the power cord. (1) Remove the 7 screws [A] and 1 screw [B] as shown in
Fig.1.
(2) Withdraw the REAR COVER toward you.
CAUTION:
When reinstalling the rear cover, carefully push it inward after inserting the MAIN PWB into the REAR COVER groove.
3.1.2 REMOVING THE MAIN PW BOARD
• Remove the REAR COVER. (1) Slightly raise the both sides of the MAIN PWB by hand. (2) Withdraw the MAIN PWB backward.
(If necessary, take off the wire clamp and connectors, etc.)
3.1.3 REMOVING THE SPEAKER
• Remove the REAR COVER. (1) Remove the 4 screws [C] as shown in Fig.1. (2) Follow the same steps when removing the other hand
SPEAKER.
3.1.4 CHECKING THE MAIN PW BOARD
• To check the back side of the MAIN PWB. (1) Pull out the MAIN PWB. (Refer to REMOVING THE MAIN
PW BOARD).
(2) Erect the MAIN PWB vertically so that you can easily check
its back side.
CAUTIONS:
• Before turning on power, make sure that the CRT earth wire
and other connectors are properly connected.
• When repairing, connect the DEG. COIL to the DEG.
connector on the MAIN PWB.
3.1.5 WIRE CLAMPING AND CABLE TYING
(1) Be sure to clamp the wire. (2) Never remove the cable tie used for tying the wires
together. Should it be inadvertently removed, be sure to tie the wires with a new cable tie.
(No.YA396)1-5
FRONT CABINET
C
SPEAKER
CRT SOCKET PWB
(Within MAIN PWB)
SPEAKER
C
MAIN PWB
POWER CORD
REAR COVER
A
B
1-6 (No.YA396)
Fig.1
3.2 MEMORY IC REPLACEMENT
• This model uses the memory IC.
• This memory IC stores data for proper operation of the video and drive circuits.
• When replacing, be sure to use an IC containing this (initial value) data.
3.2.1 MEMORY IC REPLACEMENT PROCEDURE
1. Power off
Switch off the power and disconnect the power plug from the AC outlet.
2. Replace the memory IC
Be sure to use the memory IC written with the initial setting values.
3. Power on
Connect the power plug to the AC outlet and switch on the power.
4. System constant check and setting
• It must not adjust without adjustment signals.
(1) Press the [DISPLAY] key and the [PICTURE MODE]
key of the REMOTE CONTROL UNIT simultaneously. (2) The SERVICE MENU screen of Fig. 1 will be displayed. (3) While the SERVICE MENU is displayed, again press the
[DISPLAY] key and [PICTURE MODE] key
simultaneously, and the SYSTEM CONSTANT SET
screen of Fig. 2 will be displayed. (4) Check the setting values of the SYSTEM CONSTANT
SETTING. If the value is different, select the setting item
with the [MENU /] key, and set the correct value with
the [MENU - / +] key. (5) Press the [DISPLAY] key twice, and return to the normal
screen.
5. Receiving channel setting
Refer to the OPERATING INSTRUCTIONS and set the receive channels (Channels Preset) as described.
6. User settings
Check the user setting items according to the given in page later. Where these do not agree, refer to the OPERATING INSTRUCTIONS and set the items as described.
7. SERVICE MENU setting
Verify what to set in the SERVICE MENU, and set whatever is necessary (Fig.1). Refer to the SERVICE ADJUSTMENT for setting.
SERVICE MENU
1.IF 2.V/C
3.DEF 4.VSM PRESET
5.PRESET
6.SETUP TOUR OFF
1-6 : SELECT DISP : EXIT
************ **.*** *** ** **** ***
Fig.1
SYSTEM CONSTANT- I
SYSTEM CONSTANT SET 1
COLOUR : TRIPLE BILINGUAL : YES TUNER : MU ECO SENSOR LANGUAGE : E/T
: SELECT
/
- / + : OPERATE DISP : EXIT
SYSTEM CONSTANT- II
SYSTEM CONSTANT SET 2
B/B SOUND : OFF LOCK : 180 COLOUR AUTO QSS ALC : NO TEXT RATE
: SEL - / + : OPE DISP : EXIT
/
SYSTEM CONSTANT- III
: NO
: NO : MINT
: 20
KEY ASSIGNMENT OF REMOTE CONTROL UNIT
PICTURE MODE key
NUMBERS key
DISPLAY key
MENU
- / + key
MENU
/ key
SYSTEM CONSTANT SET 3
AMP TUNER : NO VNR TEXT TABLE : CYL VOLUME PWM : POS
/
: SEL - / + : OPE DISP : EXIT
: YES
Fig.2
(No.YA396)1-7
3.2.2 SETTINGS OF FACTORY SHIPMENT
3.2.2.1 BUTTON OPERATION
Setting item Setting position
POWER Off
CHANNEL PR1
VOLUME 10
3.2.2.2 REMOTE CONTROL DIRECT OPERATION
Setting item Setting position
CHANNEL PR1
VOLUME 10
TV/VIDEO TV
PICTURE MODE BRIGHT
COLOUR SYSTEM PAL
SOUND SYSTEM B/G
3.2.2.3 REMOTE CONTROL MENU OPERATION
(1) MENU-1
Setting item Setting position
INPUT TV
ON TIMER PR1 0:00
VNR OFF
3.2.3 SYSTEM CONSTANT SETTING
Setting item Setting value
COLOUR TRIPLE
BILINGUAL YES
TUNER MU
ECO SENSOR NO
LANGUAGE E / T
B/B SOUND OFF
LOCK 180
COLOUR AUTO NO
QSS MINT
ALC NO
TEXT RATE 20
AMP TUNER NO
VNR YES
TEXT TABLE CYL
VOLUM PWM POS
(2) MENU-2
Setting item Setting position
AUTO SHUTOFF OFF
CHILD LOCK OFF
BLUE BACK OFF
(3) MENU-3
Setting item Setting position
SETUP TOUR ON
LANGUAGE THAI
(4) MENU-4
Setting item
TINT 15 15 15
COLOUR
BRIGHT 15 15 15
CONT. 30 18 14
SHARP 201512
BRIGHT STANDARD SOFT
15 15 15
Setting position
1-8 (No.YA396)
3.2.4 SERVICE MENU SETTING ITEMS
Setting item Setting value Setting item Setting value
2. V/C 1.CUT OFF
2.DRIVE
3.BRIGHT
4.CONT.
5.COLOUR
6.TINT
7.SECAM BL ADJUST
8.SHARP [Do not adjust]
9.AMP T. SHARP [Do not adjust]
3. DEFLECTION 1. VER. POSITION
2. HOR. POSITION
3. VER. HEIGHT
4. VER. LINEARITY
5. VER. SCURVE
6. HOR. VCO ADJUST [Do not adjust]
4.VSM PRESET TINT COLOUR BRIGHT CONT. SHARP
5. PRESET
[Do not adjust]
Colour System 1. C-TRAP FIX
2. SHARP PEAK
3. ABL
4. GAMMA
5. Y. DELAY TIME
6. BLACK EXP START
7. C-BPF
8. CW / SCP
9. VIF DET LEVEL
11. IF AGC MIN
12. VIF AGC
13. VIF PMOD
19. VNR
20. RGB LIM
21. RGB LIMIT LEVEL
23. TEXT H. POSITION
24. READ DATA
Sound System 10. SIF DET LEVEL
14. SIF BPF BW ADJUST
15. SIF TRAP F0 ADJUST
16. SIF TRAP F0 ADJUST 2
17. SIF -TRAP
18. SIF -BPF
22. SIF SW
3.2.5 REPLACEMENT OF IC301 (IF V/C DECODER)
For the IC301(IF V/C DECODER) of this model, all data are written in the micro-computer. So, write the data in the micro-
computer in accordance with the following procedures before starting adjustment.
PROCEDURES
(1) Turn the POWER OFF. (2) Replace the IC301 with a new one. (3) While pressing [MENU] button and [VOL+] button ON the FRONT CABINET simultaneously, turn the POWER ON. When the
POWER is turned ON, the data is written in the micro-computer immediately.
LOCATIONS OF FRONT PANEL BUTTONS
MENU
OK
CHANNEL
VOLUME
TIMER
POWER
MENU VOLUME + POWER
(No.YA396)1-9
3.3 REPLACEMENT OF CHIP COMPONENT
3.3.1 CAUTIONS
(1) Avoid heating for more than 3 seconds. (2) Do not rub the electrodes and the resist parts of the pattern. (3) When removing a chip part, melt the solder adequately. (4) Do not reuse a chip part after removing it.
3.3.2 SOLDERING IRON
(1) Use a high insulation soldering iron with a thin pointed end of it. (2) A 30w soldering iron is recommended for easily removing parts.
3.3.3 REPLACEMENT STEPS
1. How to remove Chip parts
2. How to install Chip parts
[Resistors, capacitors, etc.]
(1) As shown in the figure, push the part with tweezers and
alternately melt the solder at each end.
(2) Shift with the tweezers and remove the chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply extra solder to each lead.
SOLDER
SOLDER
[Resistors, capacitors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(2) Grasp the chip part with tweezers and place it on the
solder. Then heat and melt the solder at both ends of the chip part.
[Transistors, diodes, variable resistors, etc.]
(1) Apply solder to the pattern as indicated in the figure. (2) Grasp the chip part with tweezers and place it on the
solder.
(3) First solder lead A as indicated in the figure.
(2) As shown in the figure, push the part with tweezers and
alternately melt the solder at each lead. Shift and remove the chip part.
NOTE :
After removing the part, remove remaining solder from the pattern.
1-10 (No.YA396)
A
B
C
(4) Then solder leads B and C.
A
B
C
SECTION 4
ADJUSTMENT
4.1 ADJUSTMENT PREPARATION
(1) There are 2 ways of adjusting this TV : One is with the
REMOTE CONTROL UNIT and the other is the conventional method using adjustment parts and components.
(2) The adjustment using the REMOTE CONTROL UNIT is
made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
(3) Make sure that connection is correctly made AC to AC
power source.
(4) Turn on the power of the TV and measuring instruments for
warming up for at least 30 minutes before starting adjustments.
(5) If the receive or input signal is not specified, use the most
appropriate signal for adjustment.
(6) Never touch the parts (such as variable resistors,
transformers and condensers) not shown in the adjustment items of this service adjustment.
4.2 PRESET SETTING BEFORE ADJUSTMENT
Unless otherwise specified in the adjustment items, preset the following functions with the REMOTE CONTROL UNIT.
Item Preset value
PICTURE MODE BRIGHT
TINT / COLOUR / BRIGHT / CONT. / SHARP Centre
VNR OFF
BLUE BACK OFF
OFF TIMER OFF
AUTO SHUT OFF OFF
4.3 MEASURING INSTRUMENT AND FIXTURES
(1) DC voltmeter (or digital voltmeter) (2) Oscilloscope (3) Signal generator
(Pattern generator : PAL / SECAM / NTSC)
(4) Remote control unit
4.4 ADJUSTMENT ITEMS
CHECK ITEM
• B1 VOLTAGE check
TUNER / IF CIRCUIT
• IF VCO adjustment
• DELAY POINT adjustment
FOCUS
• FOCUS adjustment
DEFLECTION CIRCUIT
• V.HEIGHT / V.POSITION adjustment
• H. POSITION adjustment
• V.LINEARITY / V.S-CURVE adjustment
VIDEO CIRCUIT
• WHITE BALANCE adjustment
• SUB BRIGHT adjustment
• SUB CONTRAST adjustment
• SUB COLOUR adjustment
• SUB TINT adjustment
• SECAM BALACK OFFSET adjustment
VSM PRESET SETTING
• VSM PRESET setting
(No.YA396)1-11
4.5 ADJUSTMENT LOCATIONS
F901
TOP
CRT SOCKET PWB
TP-47G/R
T
IC701
(SOLDER SIDE)
U
TP-47B
TP-E
E1
CRT EARTH WIRE (BRAIDED ASS'Y)
FRONT
IC702 MEMORY IC
PW
DEG
MAIN PWB
TU001
IC301
T
1Pin TP-91(B1) 2Pin NC 3Pin X-ray1 4Pin X-ray2
5Pin TP-E( )
S1
51
U
HV
HVT
UPPER:FOCUS LOWER:SCREEN
1-12 (No.YA396)
4.6 BASIC OPERATION OF SERVICE MENU
4.6.1 TOOL OF SERVICE MENU OPERATION
Operate the SERVICE MENU with the REMOTE CONTROL UNIT.
4.6.2 SERVICE MENU ITEMS
With the SERVICE MENU, various adjustments can be made, and they are broadly classified in the following items of settings.
1.IF Adjustment of the IF circuits.
2.V/C Adjustment of the VIDEO circuit.
3.DEF Adjustment of the DEFLECTION circuit.
4.VSM PRESET Adjustment of the initial setting values of VSM condition as STANDARD, SOFT and BRIGHT.
5.PRESET Adjustment of the RF circuit [Do not adjust].
6.SETUP TOUR It should be able to select mode (LANGUAGE and AUTO CH PRESET) [Should be OFF].
4.6.3 HOW TO ENTER THE SERVICE MENU
Press the [DISPLAY] key and the [PICTURE MODE] key of the REMOTE CONTROL UNIT simultaneously. Then enter the
SERVICE MODE SELECT KEY
SERVICE MENU mode as shown in Fig.1.
SERVICE MENU
1.IF 2.V/C
3.DEF 4.VSM PRESET
5.PRESET
6.SETUP TOUR OFF
1-6 : SELECT DISP : EXIT
************ **.*** *** ** **** ***
Fig.1
4.6.4 HOW TO STORE OF SETTING VALUE
The setting value will be stored automatically when release the REMOTE CONTROL UNIT keys.
4.6.5 HOW TO EXIT THE SERVICE MENU
When complete the adjustment work, press the [DISPLAY] key to return to the SERVICE MENU. And then press the
[DISPLAY] key again to return to the normal screen.
4.6.6 SELECTION OF SUB MENU SCREEN
Press one of [1] to [5] keys of the REMOTE CONTROL UNIT and select the SUB MENU SCREEN form the SERVICE MENU.
DISPLAY key
MENU
- / + key
PICTURE MODE key
NUMBERS key
MENU
/ key
(No.YA396)1-13
4.6.7 METHOD OF SETTING
1. IF
[1. VCO]
(1) [1] key Select 1. IF.
(2) [1] key Select 1. VCO.
(3) [MENU /] keys Select setting items.
(4) [MENU - / +] keys Adjust the values of the items.
(5) [DISPLAY] key As you press this key twice, you will return to the SERVICE MENU.
[2. DELAY POINT]
(1) [1] key Select 1. IF.
(2) [2] key Select 2. DELAY POINT.
(3) [MENU - / +] keys Set (adjust) the setting values of the setting items.
(4) [DISPLAY] key When this is pressed twice, you will return to the SERVICE MENU.
NOTE:
When the setting value has been changed, the new value will be stored in memory immediately.
2. V/C, 3. DEF and 4. VSM PRESET
(1) [2] to [4] keys Select one from 2. V/C, 3. DEF and 4. VSM PRESET.
(2) [MENU /] keys Select setting items.
(3) [MENU - / +] keys Adjust the values of the items.
(4) [DISPLAY] key When this is pressed, return to the SERVICE MENU.
NOTE:
When the setting value has been changed, the new value will be stored in memory immediately.
5. PRESET (Do not adjust)
6. SETUP TOUR
(1) By pressing the [6] key, you can change the ON or OFF [should be OFF].
Should be OFF:
If it is ON, when you turn off the power and turn on a power again, the JVC’s logo will be shown about 15 seconds automatically, and the SETUP TOUR starts.
(2) [MENU - / +] keys Select Language.
(3) [MENU ] key Auto Search.
1-14 (No.YA396)
4.6.8 SERVICE MENU FLOW CHART
************ **.***
SERVICE MENU
1. IF
SERVICE MENU
1.IF 2.V/C
3.DEF 4.VSM PRESET
5.PRESET
6.SETUP TOUR OFF
1-6 : SELECT DISP : EXIT
************ **.***
6. SETUP TOUR OFF
*** ** **** ***
ON / OFF
(By pressing [6] key)
IF
1. VCO
2. DELAY POINT
1-2 : SELECT DISP : EXIT
2. V/C
V/C PAL
1. CUTOFF (G) (B)
50Hz
/ : SELECT
- / + : OPERATE DISP : EXIT
(R)
* ** * ** * **
3. DEF
VCO (CW)
TOO HIGH ABOVE REFERENCE JUST REFERENCE BELOW REFERENCE TOO LOW AFT ADJUST VCO ADJUST FINE
DISP : EXIT
DELAY POINT UHF
AGC TAKE-OVER
- / + : OPERATE DISP : EXIT
***.**
MHz
*** (** *** (**
**
) )
DEF AUTO
1. VER. POSITION
50Hz
/ : SELECT
- / + : OPERATE DISP : EXIT
**
4. VSM PRESET
BRIGHT
TINT
COLOUR BRIGHT
CONT. SHARP
/ : SELECT
- / + : OPERATE DISP : EXIT
** ** ** ** **
5. PRESET
PRESET AUTO
1. C-TRAP FIX
*
50Hz B/G
/ : SELECT
- / + : OPERATE DISP : EXIT
(No.YA396)1-15
4.7 INITIAL SETTING VALUE OF SERVICE MENU
Adjustment of the SERVICE MENU is made on the basis of the initial setting values ; however, the new setting values which
set the screen in its optimum condition may differ from the initial setting.
Do not change the initial Setting Values of the Setting (Adjustment) items not listed in "ADJUSTMENT PROCEDURE".
Setting item Variable range
1.CUT OFF RED -128 - +127 -50 -50 -50 -50
GREEN -128 - +127 -50 -50 -50 -50
BLUE -128 - +127 -50 -50 -50 -50
2.DRIVE RED -128 - +127 +0 +0 +0 +0
BLUE -128 - +127 +0 +0 +0 +0
3.BRIGHT -128 - +127 +0 +0 +0 +0
4.CONT. -63 - +63+0+0+0+0
5.COLOUR -63 - +63 +0 +0 +0 -5
6.TINT TV -63 - +63 --- --- --- ---
VIDEO -63 - +63 --- --- +0 -1
7.SECAM BL ADJUST -31 - +31 +0 +0 +0 +0
8.SHARP (Do not adjust)
9.AMP T. SHARP -31 - +31 -12 -12 -12 -12
[3. DEFLECTION]
1. VER. POSITION -4 - +3 -1 -3
2. HOR. POSITION -16 - +15 +3 +3
3. VER. HEIGHT -64 - +63 -35 +1
4. VER. LINEARITY -32 - +31 +15 -1
5. VER. SCURVE -32 - +31 -32 +0
6. HOR. VCO ADJUST
TV -31 - +31 +8 (Fixed) +8 (Fixed) +8 (Fixed) +8 (Fixed)
VIDEO -31 - +31 +15 (Fixed) +15 (Fixed) +15 (Fixed) +15 (Fixed)
Setting item Variable range
[Do not adjust]
-63 - +63 +0 +0
PAL SECAM NTSC 3.58 NTSC 4.43
Initial setting value
fv : 50Hz fv : 60Hz
Initial setting value
[4.VSM PRESET]
Setting item Variable range
TINT 0 - 30 15 15 15
COLOUR 0 - 30 15 15 15
BRIGHT 0 - 30 15 15 15
CONT. 0 - 30 30 18 14
SHARP 0 - 30 20 15 12
1-16 (No.YA396)
BRIGHT STANDARD SOFT
Initial setting value
[5. PRESET]
The items in the following table, it is no requirement for adjustment.If values had changed by the miss operation, set the initial setting values in the following table.
z COLOUR SYSTEM (Do not adjust)
Setting item Variable range
1. C TRAP FIX 0 - 1 1 1 1 1
2. SHARP PEAK 0 - 1 0 0 0 0
3. ABL 0 - 11111
4. GAMMA 0 - 1 0 0 0 0
5. Y. DELAY TIME TV 0 - 3 0 2 2 3
VIDEO 0 - 30202
6. BLACK EXP START 0 - 3 3 3 3 3
7. C-BPFTV 0 - 11100
VIDEO 0 - 11111
8. CW / SCP 0 - 1 0 0 0 0
9. VIF DET LEVEL -63 - +63 0 0 0 0
11. IF AGC MIN 0 - 1 0 0 0 0
12. VIF AGC 0 - 1 0 0 0 0
13. VIF PMOD 0 - 1 0 0 0 0
19. VNR 0 - 63 15 15 15 15
20. RGB LIM 0 - 1 1 1 1 1
21. RGB LIMIT LEVEL 0 - 7 2 2 2 2
23. TEXT H. POSITION -16 - +15 -3 -3 -3 -3
24. READ DATA --- --- --- --- ---
PAL SECAM NTSC 3.58 NTSC 4.43
Initial setting value (Fixed value)
z SOUND SYSTEM (Do not adjust)
Setting item Variable range
10. SIF DET LEVEL -7 - +7 +0 +0 +0 +0
14. SIF BPF BW ADJUST -7 - +7 ( - ) ( - ) ( - ) ( - )
15. SIF TRAP FO ADJUST -7 - +7 ( - ) ( - ) ( - ) ( - )
16. SIF TRAP FO ADJUST 2 -7 - +7 ( - ) ( - ) ( - ) ( - )
17. SIF -TRAP 0 - 10000
18. SIF -BPF 0 - 10001
22. SIF SW 0 - 11110
B/G I D/K M
Initial setting value (Fixed value)
(No.YA396)1-17
4.8 ADJUSTMENT PROCEDURE
4.8.1 CHECK ITEM
Item
B1 VOLTAGE Signal
Measuring
instrument
generator
DC voltmeter
TP-B1 : 1-pin TP-E : 5-pin (S1 connector) [MAIN PWB]
4.8.2 TUNER / IF CIRCUIT
Test point Adjustment part Description
(1) Receive a whole black signal. (2) Connect a DC voltmeter to 1-pin and 5-pin of S1
connector.
(3) Make sure that the voltage is DC116.2V±2.0V.
Item
Measuring
instrument
IF VCO Signal
generator
Remote control unit
VCO (CW)
TOO HIGH ABOVE REFERENCE JUST REFERENCE BELOW REFERENCE TOO LOW AFT ADJUST VCO ADJUST FINE
DISP : EXIT
ADJUSTMENT AT THIS POINT IS USELESS
***.**
Test point Adjustment part Description
[1. IF]
1. VCO
• Please use a signal generator which frequency output is correctly calibrated. (1) Receive any broadcast. (2) Select 1.IF from the SERVICE MENU. (3) Select < 1.VCO >. (4) Select VCO ADJUST with [MENU /] key.
MHz
(5) Press [MENU - / +] keys until the colour of the
characters TOO HIGH changes blue to yellow. Then gradually press the [MENU - / +] keys until the TOO
YELLOW
LOW changes yellow. At this time, confirm that the value of VCO ADJUST is near +00.
***(** ***(**
) )
(6) Select AFT ADJUST with [MENU /] key. (7) Press [MENU - / +] keys until the characters JUST
REFERENCE changes blue to yellow.
(8) Press the [DISPLAY] key three times to return to
normal screen.
TOO HIGH
ABOVE REFERENCE
JUST REFERENCE
BELOW REFERENCE
TOO LOW
ADJUSTMENT POINT
1-18 (No.YA396)
Item
DELAY POINT (AGC)
Measuring instrument
Test point Adjustment part Description
Signal generator
Remote control unit
DELAY POINT UHF
AGC TAKE-OVER **
- / + : OPERATE DISP : EXIT
[1. IF]
2. DELAY POINT (AGC TAKE-OVER)
(1) Receive a black and white signal (colour off). (2) Select 1. IF. (3) Select < 2. DELAY POINT >. (4) Set the setting values of the setting items as shown
bellow table.
(5) Then adjust the [MENU - / +] keys until video noise
disappears.
(6) Turn to other channels and make sure that there are
no irregularities.
Setting Item
DELAY POINT (AGC TAKE-OVER)
NTSC3.58
OTHER
4.8.3 FOCUS
Item
Measuring instrument
FOCUS Signal
generator
Variable range
0 - 127
Initial setting value
45
35
Test point Adjustment part Description
FOCUS VR [In HVT]
(1) Receive a crosshatch signal. (2) While watching the screen, adjust the FOCUS VR to
make the vertical and horizontal lines as fine and sharp as possible.
(3) Make sure that when the screen is darkened, the
lines remain in good focus.
(No.YA396)1-19
4.8.4 DEFLECTION CIRCUIT
• There are 2 modes of adjustment (setting value) 50Hz mode and 60Hz mode, depending upon the kind of signals (vertical frequency 50Hz / 60Hz).
• When adjusted in 50Hz mode and 60Hz mode will be automatically set.
The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values.The setting values which adjust the screen to the optimum condition can be different from the initial setting values.
• Make sure that the adjustment is properly done on the screen of 60Hz mode.
NOTE:
• Adjust to make both 50Hz & 60Hz are the same v. size and fine straight line.
• When adjust again, adjust 50Hz mode first.
• When adjust in 60Hz mode, only 60Hz mode is adjust.
Item
V. HEIGHT / V. POSITION
Measuring
instrument
Signal generator
Remote control unit
Test point Adjustment part Description
[3. DEF]
1. VER. POSITION
3. VER. HEIGHT
(1) Receive a crosshatch signal. (2) Select 3. DEF from the SERVICE MENU. (3) Select < 1. VER. POSITION >. (4) Set the initial setting value of < 1. VER. POSITION >. (5) Adjust < 1. VER. POSITION > to make the vertical
centre fall on the display centre. (6) Select <3. VER. HEIGHT >. (7) Set the initial setting value of <3. VER. HEIGHT >.
Screen
size
Picture
size
100%
(8) Adjust <3. VER. HEIGHT > to make the vertical
screen size be 92% of the picture size.
H. POSITION Signal
generator
Remote control unit
V.LINEARITY / V.S-CURVE
Signal generator
Remote control unit
(A)
Fig.1
Fig.2
[3. DEF]
2. HOR. POSITION
(B)
[3. DEF]
4. VER. LIN.
5. VER. SCURVE
Top
Centre
(1) Receive a circle pattern signal. (2) Select 3. DEF from the SERVICE MENU. (3) Select < 2. HOR. POSITION >. (4) Set the initial setting value of < 2. HOR. POSITION >. (5) Adjust <2.HOR. POSITION> to be equal the width of
(A) and (B) as shown in Fig.2.
• If the vertical linearity is noticeably deteriorated, perform the following steps. (1) Receive a crosshatch signal. (2) Select 3. DEF from the SERVICE MENU. (3) Select < 4. VER. LIN. >. (4) Set the initial setting value of < 4. VER. LIN. >. (5) Select < 5. VER. SCURVE >. (6) Set the initial setting value of < 5. VER. SCURVE >. (7) Adjust < 4. VER. LIN. > and < 5. VER. SCURVE >
so that the space of upper and lower lines as shown in Fig.3 on TOP, CENTRE and BOTTOM become uniform.
1-20 (No.YA396)
Bottom
Fig.3
4.8.5 VIDEO CIRCUIT The setting (adjustment) using the REMOTE CONTROL UNIT is made on the basis of the initial setting values. The setting values which adjust the screen to the optimum condition can be different from the initial setting values. Do not change the initial setting values of the setting items not listed in "ADJUSTMENT PROCEDURE".
Item
WHITE BALANCE (LOW LIGHT)
Measuring instrument
Signal generator
Remote control unit
Test point Adjustment part Description
[2.V/C]
1. CUT OFF (R)
1. CUT OFF (G)
1. CUT OFF (B)
SCREEN VR [IN HVT]
(1) Receive a black and white signal (colour off). (2) Select 2. V/C from the SERVICE MENU. (3) Select < 1. CUT OFF >. (4) Set the initial setting value of < 1. CUT OFF >. (5) Press the [1] key to show the single horizontal line
on screen.
(6) Turn the SCREEN VR fully counter-clockwise, then
slowly turn it clockwise to where one of a red, blue or
KEY ASSIGNMENT OF REMOTE CONTROL UNIT
green colour is faintly visible.
(7) Adjust the two colors which did not appear until the
CUTOFF OFF
(H.LINE OFF)
CUTOFF ON
(H.LINE ON)
R. CUTOFF( )
R. CUTOFF( )
123
456
789
G.CUTOFF( )
B. CUTOFF( )
B. CUTOFF( )
G.CUTOFF( )
single horizontal line that is displayed becomes white using the [4] to [9] keys.
(8) Turn the SCREEN VR to where the single horizontal
line glows faintly.
(9) Press the [2] key to turn off the single horizontal line.
(10) Press the [DISPLAY] key twice to return to the nor-
mal screen.
R G B
WHITE BALANCE (HIGH LIGHT)
Signal generator
Remote control unit
KEY ASSIGNMENT OF REMOTE CONTROL UNIT
R. DRIVE( )
SUB BRIGHT Remote
control unit
SUB CONTRAST
Remote control unit
123
456
789
R B
[2.V/C]
2. DRIVE (R)
2. DRIVE (B)
B. DRIVE( )
B. DRIVE( )R. DRIVE( )
[2. V/C]
3. BRIGHT
[2. V/C]
4. CONT.
(1) Receive a black and white signal (colour off). (2) Select 2. V/C from the SERVICE MENU. (3) Select < 2. DRIVE >. (4) Set the initial setting value of < 2. DRIVE >. (5) Adjust the screen until it becomes white using the
[4], [6], [7] and [9] keys.
(6) Press the [DISPLAY] key twice to return to the nom-
al screen.
(1) Receive any broadcast. (2) Select 2. V/C from the SERVICE MENU. (3) Select < 3. BRIGHT >. (4) Set the initial setting value of < 3. BRIGHT >. (5) If the brightness is not the best with the initial setting
value, make fine adjustment until you get the best brightness.
(1) Receive any broadcast. (2) Select 2. V/C from the SERVICE MENU. (3) Select < 4. CONT >. (4) Set the initial setting value of < 4. CONT >. (5) If the contrast is not the best with the initial setting
value, make fine adjustment until you get the best contrast.
(No.YA396)1-21
Item
Measuring
instrument
SUB COLOUR Remote
control unit
Signal generator
Oscilloscope
Remote control unit
W
MODEL
AV-21D116/B ---+12V +3V +6V (VDO)
Test point Adjustment part Description
[2. V/C]
5. COLOUR (PAL / SECAM / NTSC)
TP-47G/R TP-E [CRT SOCKET
[2. V/C]
5. COLOUR (PAL / SECAM / NTSC)
PWB]
B
R
M
0V
Y
C
(A)
(+)
G
Voltage setting (A)
PAL SECAM NTSC3.58 NTSC4.43
[Method of adjustment without measuring instrument]
PAL COLOUR
(1) Receive a PAL broadcast. (2) Select 2. V/C from the SERVICE MENU. (3) Select < 5. COLOUR >. (4) Set the initial setting value of < 5. COLOUR >. (5) If the colour is not the best with the initial setting
value, make fine adjustment until you get the best colour.
SECAM COLOUR
(1) Receive a SECAM broadcast. (2) Make fine adjustment of SECAM COLOUR as
previously.
NTSC 3.58 COLOUR
(1) Receive a NTSC 3.58MHz broadcast. (2) Make similar fine adjustment of NTSC 3.58
COLOUR as previously.
NTSC 4.43 COLOUR
(1) When NTSC 3.58 adjustment completed, NTSC
4.43 will be automatically set at the respective values.
[Method of adjustment using measuring instrument]
PAL COLOUR
(1) Receive a PAL full field colour bar signal (75%
white). (2) Select 2. V/C from the SERVICE MENU. (3) Select < 5. COLOUR >. (4) Set the initial setting value of < 5. COLOUR >. (5) Connect the oscilloscope between TP-47G/R and
TP-E. (6) Adjust PAL COLOUR to bring the value of (A) in
the voltage table.
SECAM COLOUR
(1) Receive a SECAM full field colour bar signal (75%
white). (2) Set the initial setting value of SECAM COLOUR . (3) Adjust SECAM COLOUR to bring the value of (A)
in the voltage table.
NTSC 3.58 COLOUR
(1) Receive a NTSC 3.58 full field colour bar signal
(75% white). (2) Set the initial setting value of NTSC 3.58
COLOUR. (3) Adjust NTSC 3.58 COLOUR to bring the value of
(A) in the voltage table.
NTSC 4.43 COLOUR
(1) When NTSC 3.58 is set, NTSC 4.43 will be
automatically set at the respective values.
1-22 (No.YA396)
Item
Measuring instrument
SUB TINT Signal
generator
Remote control unit
Signal generator
Oscilloscope
Remote control unit
Test point Adjustment part Description
[2. V/C]
6. TINT
[Method of adjustment without measuring instrument]
NTSC 3.58 TINT
(1) Receive a NTSC 3.58 full field colour bar signal
(75% white). (2) Select 2. V/C from the SERVICE MENU. (3) Select < 6. TINT >. (4) Set the initial setting value of < 6. TINT >. (5) If you cannot get the best tint with the initial setting
value, make fine adjustment until you get the best
tint.
NTSC 4.43 TINT
(1) When NTSC 3.58 is set, NTSC 4.43 will be
automatically set at the respective values.
TP-47G/R TP-E [CRT SOCKET PWB]
[2. V/C]
6. TINT
[Method of adjustment using measuring instrument]
NTSC 3.58 TINT
(1) Receive a NTSC 3.58 full field colour bar signal
(75% white). (2) Select 2. V/C from the SERVICE MENU. (3) Select < 6. TINT >. (4) Set the initial setting value of < 6. TINT >. (5) Connect the oscilloscope between TP-47G/R and
TP-E. (6) Adjust NTSC 3.58 TINT to bring the value of (B)
in the voltage table in the left.
B
R
M
NTSC 4.43 TINT
(1) When NTSC 3.58 is set, NTSC 4.43 will be
automatically set at the respective values.
MODEL
AV-21D116/B
W
Y
C
Voltage setting (B)
NTSC3.58 NTSC4.43
(-)
0V
(B)
(+)
G
---+4V (VDO)
(No.YA396)1-23
Item
VSM PRESET
SECAM BLACK OFFSET
Measuring
instrument
Signal generator
Remote control unit
4.8.6 VSM PRESET SETTING
Test point Adjustment part Description
[2. V/C]
7. SECAM BL ADJUST
(1) Input a SECAM full field colour bar signal. (2) Select 2. V/C from the SERVICE MENU. (3) Select < 7. SECAM BL ADJUST >. (4) Set the initial setting value of < 7. SECAM BL
ADJUST >.
(5) Switch the [1] key (colour OFF) and [2] key (colour
ON) and make sure that there is no colour on the black and white screen.
(6) If the black and white screen is not best with the
initial setting value, make fine adjustment until you get the best black and white screen.
(7) While watching the screen, adjust the value to be the
same colour between ON & OFF by [1] or [2] key.
(8) Press the [DISPLAY] key twice to return to the
normal screen.
Item
Measuring
instrument
VSM PRESET Remote
control unit
/ : SELECT
- / + : OPREATE DISP : EXIT
Test point Adjustment part Description
[4. VSM PRESET] TINT COLOUR BRIGHT CONT. SHARP
(1) Select 4. VSM PRESET from the SERVICE MENU. (2) Set the PICTURE MODE to BRIGHT. (3) Select < TINT >. (4) Set the initial setting value of < TINT > as shown in
the below table.
(5) Select < COLOUR > to < SHARP > in turn, and set
the values.
(6) Respectively select the "SOFT" and "STANDARD".
BRIGHT
TINT ** COLOUR ** BRIGHT **
CONT. SHARP **
**
Make similar adjustment as same step as above.
VSM PRESET
Setting item
TINT
COLOUR
BRIGHT
CONT.
SHARP
BRIGHT
15
15
15
30
20
STANDARD SOFT
18
15
14
12
1-24 (No.YA396)
SECTION 5
TROUBLESHOOTING
This service manual does not describe TROUBLESHOOTING.
Victor Company of Japan, Limited Display Category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan
(No.YA396)
Printed in Japan
VPT
COLOUR TELEVISION
INSTRUCTIONS
Thank you for buying this JVC colour television. To make sure you understand how to use your new TV, please read this manual thoroughly before you begin.
AV-14F116 AV-21B116 AV-21C116 AV-21D116 AV-21V116
Contents
Safety precautions 2 Preparation 3
1 Confirm which remote control you have 2 Inserting the batteries 3
Connecting the aerial and external devices 4 Connecting the power cord 5 SETUP TOUR
...................................
........................
..............................................
......
...
Basic operation 7 Remote control buttons and functions 8
PICTURE MODE button COLOUR SYSTEM button SOUND SYSTEM button I/II button DISPLAY button RETURN + button CHANNEL SCAN button MUTING button OFF TIMER button
........................................................
.................................
.............................
...............................
.............................................
..........................................
................................
.............................................
.........................................
Using the TV’s menus 10
Basic operation ON TIMER
...........................................................
INPUT
...............................................................
VNR AUTO SHUTOFF CHILD LOCK BLUE BACK SETUP TOUR LANGUAGE AUTO CH PRESET MANUAL CH PRESET
..............................................................
SKIP Picture Adjustments
............................................
.....................................................
..........................................
.................................................
..................................................
...............................................
..................................................
.......................................
..................................
....................................
10 11 11 12 12 12 12 13 13 13 14 15 15
Using the buttons on the TV 16 Troubleshooting 18 Specifications 19
3 3 4 6 6
8 8 8 8 9 9 9 9 9
GGT0111-001A-H 0306-NIC-JMT
© 2006 Victor Company of Japan, Limited
Safety precautions
WARNING
•To prevent fire or shock hazard, do not expose the TV to rain or moisture.
CAUTION
• Operate only from the power source indicated on the rear of the TV.
•Avoid damaging the power cord and mains plug. When you unplug the TV, pull it out by the mains plug. Do not pull on the power cord.
•Never block or cover the cabinet openings for ventilation. Never install the TV where good ventilation is unattainable. When installing this TV, leave spaces for ventilation around the TV more than the minimum distances shown in the diagram.
• Do not allow objects or liquid into the cabinet openings.
• In the event of a fault, unplug the TV and call a service technician. Do not attempt to repair it by yourself or remove the rear cover.
• The surface of the TV screen is easily damaged. Be very careful with it when handling the TV. Should the TV screen become soiled, wipe it with a soft dry cloth. Never rub it forcefully. Never use any cleaner or detergent on it.
•This TV can be turned on/ off power by connecting/ disconnecting the AC Plug into AC outlet. While this TV is being installed, enough space should be reserved for connecting/ disconnecting the AC Plug into AC outlet by hand.
10 cm 15 cm
10 cm
15 cm
2
Preparation
1 Confirm which remote control you have
RM-C1121
2 Inserting the batteries
Correctly insert two batteries, observing the , and . polarities and inserting the . end first.
CAUTION:
Follow the cautions printed on the batteries.
Notes:
• Use AA/R6/UM-3 dry cell batteries.
• If the remote control does not work properly, fit new batteries. The supplied batteries are for testing, not regular use.
3
Preparation
3 Connecting the aerial and external devices
•For further details, refer to the manuals provided with the devices you are connecting.
• Connecting cables are not supplied.
• The front and rear AUDIO/VIDEO input jacks are directly connected so that input to either jack is output through both. You cannot provide input to both the front and rear jacks at the same time. Disconnect one input, or use one of the jacks as an output jack only (for monitoring or recording).
Connecting the aerial and VCR
Connecting the aerial
  
* AV-14F116 only.
Connecting the aerial and VCR
VHF/UHF outdoor aerial


   


2
 
 
 
• Illustration of AV-14F116
VIDEO
AUDIO
IN
OUT
3

 
!
1
To RF output
To aerial input
To video output
VCR
To audio output
• Illustration of AV-14F116.
4
Preparation
Connecting other external devices
VIDEO
AUDIO
IN
OUT
• Illustration of AV-14F116.
Camcorder or TV game
To audio output
VCR (for playing)
VCR (for recording)
To audio input
To video output
To video output
To video input
To audio output
VIDEO AUDIO
IN
MENU CHANNEL
• Illustration of AV-14F116.
Headphones
• Use the headphones with a stereo mini jack (3.5 mm in diameter). When you connect the headphones, the TV speakers go off.
5
Preparation
4 Connecting the power cord
Connect the power cord to the AC outlet. Operate only from the power source indicated on the rear of the TV.
5 SETUP TOUR
When the TV is first turned on it enters the SETUP TOUR mode, and the JVC logo is displayed. Follow the instructions on the on-screen display to perform the SETUP TOUR.
• In case of resetting that the reason for such as removal, you can set the SETUP TOUR function on the “MENU 3” menu. For details, see page 13.
1 Press the Main power button
on the TV.
The POWER lamp or POWER/ON TIMER lamp lights. After the JVC logo has been displayed, the TV automatically switches to the language setting mode.
2 Press the MENU M buttons to
select the on-screen language.
3 Press the MENU y button.
The AUTO PROGRAMMING function will start and the indicator blinks.
• Illustration of AV-14F116
ON TIMER POWER
POWER lamp Main power button
DISPLAY
button
-
/+
MENU
buttons
MENU /
buttons
•To stop the AUTO PROGRAMMING function, press the MENU m buttons.
When you press stop, it will display “SETUP TOUR THANK YOU!”.
When all the TV channels that can be received on your TV have been preset, the display goes out and the AUTO PROGRAMMING function operation is completed.
6
• If a TV channel you want to view is not set to the channel, set it with the MANUAL CH PRESET function. For details, see page 14.
Basic operation
1 Press the POWER button to turn
your TV on.
• If your TV does not turn on, press the Main power button on the TV then press the POWER button again.
•You can also turn on your TV by pressing any of the following buttons;
- the CHANNEL m button
- the Number buttons
- the TV/VIDEO button
2 Select a channel.
Press the CHANNEL m button.
• Up/down selection cannot be selected for channels to which the SKIP has been set to “YES”. See page 15.
Press the Number buttons to enter the channel number.
• If you want to enter a two-digit number,
press the -/-- button to select the two digit mode “--”, then enter the channel number.
3 Press the VOLUME M button to
adjust the sound.
4To turn your TV off, press the
POWER button.
•We recommend that you press the Main
power button on the TV to turn the main power off if you do not plan to use your TV for a long time or if you wish to save energy.
If the picture is not clear:
Press the COLOUR SYSTEM button to select another colour system, see page 8.
If the sound is not clear:
Press the SOUND SYSTEM button to select another sound system, see page 8.
Viewing Images from an External Device:
Press the TV/VIDEO button to select the VIDEO mode.
•You can also use the INPUT function to select the VIDEO mode. For details, refer to page 11.
7
Remote control buttons and functions
PICTURE MODE button
You can select one of three picture adjustment settings as you like.
Press this button to select a mode.
BRIGHT:
Heightens contrast and sharpness.
STANDARD:
Standardizes picture adjustments.
SOFT:
Softens contrast and sharpness.
•Pressing this button returns all the picture
settings in the “MENU 4” to their default settings.
COLOUR SYSTEM button
If the picture is not clear or no colour appears, change the current colour system to another colour system.
Press this button to select the colour system.
In TV mode (channel 1 to 99 and AV):
AUTO PAL
SECAM
In VIDEO mode:
AUTO PAL
NTSC4.43
SECAM
NTSC3.58
AUTO:
Automatic colour system selection.
• If the picture is not normal in the AUTO mode, change the AUTO mode to another colour system.
SOUND SYSTEM button
If the sound is not clear even when the picture appears normal, change the current sound system to another sound system.
Press this button to select the sound system.
B/G I D/K
•You cannot select any sound system when in a VIDEO mode.
I/II button
You can select one of the two bilingual sounds in an A2 stereo programme’s bilingual programme. Press the A2 Bilingual button to select a bilingual sound.
I : Bilingual I sound
II : Bilingual II sound
• The A2 Bilingual function has no effect on
stereo programmes of the A2 stereo broadcast programme type, although an A2 Bilingual function indicator will appear on the screen.
• The A2 Bilingual function has no effect on
programmes other than A2 stereo broadcast
programme type, although an A2 Bilingual
function indicator will appear on the screen.
• The A2 Bilingual function has no effect in
Video mode, although an A2 Bilingual
function indicator will appear on the screen.
8
Remote control buttons and functions
DISPLAY button
You can continuously display the current channel number or VIDEO mode on the screen.
Press this button.
To turn the display off, press this button again.
• When selecting a channel or VIDEO mode with no input signal, indication of selected channel or VIDEO mode becomes fixed on the screen.
RETURN + button
You can set a channel you frequently view to the Return Channel and you can view that channel at any time with one-touch.
To set the channel to the Return Channel:
1 Select the channel you want to set
to the Return Channel.
2 Press this button and hold until the
message “RETURN PLUS PROGRAMMED!” appears.
• When you turn off the TV, the Return Channel setting is cancelled.
To view the Return Channel:
Press this button.
•You can view two channels (current channel and Return Channel) alternately by pressing this button.
To cancel the Return Channel setting:
Press this button and hold until the message“RETURN PLUS CANCELLED!” appears.
If no channel is set to the Return Channel:
You can view the channel selected right before the current channel by pressing this button.
CHANNEL SCAN button
You can quickly view all TV channels programmes that you can view on your TV, and search for the programme you want to view.
1 Press this button to start scanning
TV channels.
The TV channel programmes are each displayed for several seconds.
• The programmes of TV channels for which
the SKIP function is set to “YES” are not displayed. (See page 15.)
2 When you find the programme you
want to view, press this button again to stop scanning.
MUTING button
You can turn the sound off instantly.
Press this button.
To turn the sound on, press this button again.
OFF TIMER button
You can set the TV to automatically turn off after a set time.
Press this button to select the period of time.
•You can set the period of time to a maximum of 120 minutes in 10 minute increments.
•1 minute before the OFF TIMER function turns off the TV, “GOOD NIGHT!” appears.
To display the remaining time, press this button once.
To cancel the OFF TIMER function, press this button to set the period of time to 0.
• The OFF TIMER function will not turn off the TV’s main power.
9
Using the TV’s menus
This TV has a number of functions you can operate using the menus. To use all your TV’s functions fully, you need to understand how to use the menus.
2 Repeatedly press the MENU T
buttons to display a desired menu.
• If you hold down the y button, the next
menu is displayed.
• If the selected function is on the first line,
pressing the r button displays the preceding menu.
3 Repeatedly press the MENU T
buttons to select a desired
DISPLAY
button
MENU
buttons
-
/+
MENU /
buttons
function.
4 Press the MENU M buttons to
change function settings.
Basic operation
1 Press the MENU T buttons.
One of the 4 menus is displayed.
MENU number
MENU 1
The icon on the left indicates the currently selected function.
INPUT TV ON TIMER PR 1 0:00 VNR OFF
SELECT BY EXIT BY OPERATE BY -+
DISPLAY
Example:
Changes the AUTO SHUTOFF setting.
MENU 2 AUTO SHUTOFF OFF CHILD LOCK OFF BLUE BACK ON
SELECT BY EXIT BY OPERATE BY -+
DISPLAY
MENU 2 AUTO SHUTOFF ON CHILD LOCK OFF BLUE BACK ON
SELECT BY EXIT BY OPERATE BY -+
DISPLAY
• With some functions, the operation method may differ.
5 Press the DISPLAY button to turn
the display off.
•To operate a menu using the buttons on the front panel of the TV, refer to “Operating menus” on page 17.
10
Using the TV’s menus
ON TIMER
Your TV will automatically turn on and tune into the channel you set after the period of time you set.
1 Press MENU T to display the
“MENU 1” menu, then select “ON TIMER”.
MENU 1 INPUT TV ON TIMER PR 1 0:00 VNR OFF
OPERATE BY VOL-+ SELECT BY EXIT BY PROGRAM BY -+
2 Press MENU M to select a channel
you want to view when the TV turns on.
3 Press VOLUME M to select the
period of time after which you want to turn on the TV.
The ON TIMER function starts.
• Each time you press the button, the period of time changes in 15 minute intervals (up to 12 hours).
To cancel the ON TIMER function, press the VOLUME m button to set the period of time to “0:00”.
4 Press DISPLAY to turn the display
off.
• If you turn off the TV’s main power by pressing the Main power button, the ON TIMER function is canceled.
• If you do not turn off the TV after starting the ON TIMER function, the channel will automatically switch to the channel set for the ON TIMER function.
Channel No.
DISPLAY
When the time set for the ON TIMER function is reached:
The TV automatically turns on and the channel set for the ON TIMER function is displayed.
•For safety reasons the TV will automatically turn off if no operations are made within approximately two hours after the TV is turned on with the ON TIMER function.
• The OFF TIMER function and AUTO SHUTOFF function have priority over the ON TIMER function.
INPUT
You can view images from VCRs or other devices connected to your TV.
1 Press MENU T to display the
“MENU 1” menu, then select “INPUT”.
MENU 1 INPUT TV ON TIMER PR 1 0:00 VNR OFF
SELECT BY EXIT BY OPERATE BY -+
2 Press MENU M to select the VIDEO
mode.
While you press MENU –/+, it will switch to TV mode and VIDEO mode alternately.
DISPLAY
11
Using the TV’s menus
VNR (Video Noise Reduction)
You can reduce the picture noise.
1 Press MENU T to display the
“MENU 1” menu, then select “VNR”.
MENU 1 INPUT TV ON TIMER PR 1 0:00 VNR ON
SELECT BY EXIT BY OPERATE BY -+
DISPLAY
2 Press MENU M to select “ON”.
To cancel the VNR function, select “OFF”.
AUTO SHUTOFF
You can set your TV to turn off if no signals are received for about 15 minutes or longer after the end of a broadcast.
1 Press MENU T to display the
“MENU 2” menu, then select “AUTO SHUTOFF”.
MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON
SELECT BY EXIT BY OPERATE BY -+
2 Press MENU M to select “ON”.
To cancel the AUTO SHUTOFF function, select “OFF”.
• The AUTO SHUTOFF function does not turn off the TV’s main power.
• The AUTO SHUTOFF will not work for a VIDEO mode.
DISPLAY
CHILD LOCK
You can disable the front control buttons of the TV. When this function is set to “ON”, the TV can be operated using only the remote control. Use this function to prevent children from operating the TV without parental consent.
1 Press MENU T to display the
“MENU 2” menu, then select “CHILD LOCK”.
MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON
SELECT BY EXIT BY OPERATE BY -+
DISPLAY
2 Press MENU M to select “ON”.
To cancel the CHILD LOCK function, select “OFF”.
• The CHILD LOCK function is canceled when you turn the power off.
BLUE BACK
You can mute the sound and change the picture into a blue screen while no signals are received by the TV, or when the signals are unstable.
1 Press MENU T to display the
“MENU 2” menu, then select “BLUE BACK”.
MENU 2 AUTO SHUTOFF ON CHILD LOCK ON BLUE BACK ON
SELECT BY EXIT BY OPERATE BY -+
DISPLAY
12
2 Press MENU M to select “ON”.
To cancel the BLUE BACK function, select “OFF”.
•To view a broadcast even when the reception signal is poor, set the BLUE BACK function to “OFF”.
•Even when the BLUE BACK function is set to “OFF”, the sound may not be audible.
Using the TV’s menus
SETUP TOUR
You can start the SETUP TOUR function.
1 Press MENU T to display the
“MENU 3” menu, then select “SETUP TOUR”.
MENU 3 AUTO CH PRESET MANUAL CH PRESET SETUP TOUR LANGUAGE ENGLISH
SELECT BY EXIT BY OPERATE BY -+
DISPLAY
2 Press MENU M.
JVC logo is appear and the SETUP TOUR function will start. For details, see page 6.
LANGUAGE
You can select the language for the on­screen display.
1 Press MENU T to display the
“MENU 3” menu, then select “LANGUAGE”.
MENU 3 AUTO CH PRESET MANUAL CH PRESET SETUP TOUR LANGUAGE ENGLISH
SELECT BY EXIT BY OPERATE BY -+
2 Press MENU M to select
language.
The on-screen display indications are in the selected language.
DISPLAY
AUTO CH PRESET
You can automatically preset all TV channels that can be received by your TV to channels.
1 Press MENU T to display the
“MENU 3” menu, then select “AUTO CH PRESET”.
MENU 3 AUTO CH PRESET MANUAL CH PRESET SETUP TOUR LANGUAGE ENGLISH
SELECT BY EXIT BY OPERATE BY -+
2 Press MENU M to start the AUTO
CH PRESET function.
“>>>ON SEARCH” is displayed on the screen.
When all the TV channels that can be received on your TV have been preset, the display goes out and the AUTO CH PRESET function operation is completed.
To stop the AUTO CH PRESET:
Press the MENU m buttons.
• The AUTO CH PRESET function does not preset a TV channel to the AV channel (channel number 0).
• If the TV cannot preset the TV channel you want to view, preset it manually. For details, see “MANUAL CH PRESET” on page 14.
DISPLAY
13
Using the TV’s menus
MANUAL CH PRESET
You can manually preset desired TV channels to desired channels.
1 Press MENU T to display the
“MENU 3” menu, then select “MANUAL CH PRESET”.
MENU 3 AUTO CH PRESET MANUAL CH PRESET SETUP TOUR LANGUAGE ENGLISH
SELECT BY EXIT BY OPERATE BY -+
2 Press MENU M.
The sub-menu is displayed.
MANUAL FINE SKIP NO SOUND SYSTEM B/G EXIT
SELECT BY PR 1 VL PROGRAM BY -+ EXIT BY SEARCH BY VOL-+
• The channel number is displayed as a PR number. For example, channel 1 will be displayed as PR 1. However, the AV channel will be displayed as AV.
3 Press MENU M to select the
channel number.
4 Press VOLUME M to start
searching for the TV channel.
“>>>” or “<<<” is displayed on the screen.
When the TV finds a TV channel, the “>>>” or “<<<” display goes out, and the TV channel is preset to the currently selected channel number.
• If the TV channel you want to preset is not displayed, repeat step 4 until the TV finds the TV channel you want to preset.
•To stop the MANUAL CH PRESET function, press any button other than the VOLUME m button.
DISPLAY
DISPLAY
If the picture is not clear:
Fine-tune the TV channel.
1 Press MENU t to select “FINE”.
MANUAL FINE SKIP NO SOUND SYSTEM B/G EXIT
SELECT BY PR 3 VL PROGRAM BY -+ EXIT BY FINE BY VOL-+
DISPLAY
2 Hold VOLUME m down to fine-tune
the TV channel so that the best image is displayed on screen.
“>” or “<” indicates that the TV is fine­tuning the TV channel.
If the sound is not clear:
1 Press MENU t to select “SOUND
SYSTEM”.
MANUAL FINE SKIP NO SOUND SYSTEM B/G EXIT
SELECT BY PR 3 VL PROGRAM BY -+ EXIT BY CHANGE BY VOL-+
DISPLAY
2 Press VOLUME m to select the
appropriate sound system.
5 Press MENU T to select
“MANUAL”.
6 Repeat steps 3 to 5 if you want to
preset another TV channel to a channel.
14
Using the TV’s menus
SKIP
You can set undesired channels to be skipped. Channels set to be skipped cannot be selected by the CHANNEL m buttons nor the CHANNEL SCAN button.
• Channels to which TV channels have not been preset are automatically set to be skipped.
1 Press MENU T to display the
“MENU 3” menu, then select “MANUAL CH PRESET”.
2 Press MENU M.
The sub-menu is displayed.
3 Press MENU T to select “SKIP”.
MANUAL FINE SKIP NO SOUND SYSTEM B/G EXIT
SELECT BY PR 3 VL PROGRAM BY -+ EXIT BY YES/NO BY VOL-+
4 Press MENU M to select the
channel you want to skip.
5 Press VOLUME M to select “YES”.
The channel is set to be skipped. To cancel the SKIP function, select “NO”.
DISPLAY
Picture Adjustments
You can adjust the picture as you like.
1 Press MENU T to display the
“MENU 4” menu.
MENU 4 TINT COLOUR BRIGHT CONT. SHARP
SELECT BY EXIT BY OPERATE BY -+
2 Press MENU T to select an item
and press MENU M to adjust it.
TINT* - : Reddish + : Greenish COLOUR - : Lighter + : Deeper BRIGHT - : Darker + : Brighter CONT. - : Lower + : Higher SHARP - : Softer + : Sharper
* TINT (tint) is displayed only when
viewing images from NTSC3.58 or NTSC4.43 colour systems.
DISPLAY
6 Repeat steps 4 and 5 if you want to
set another channel to skip.
15
Using the buttons on the TV
The following illustrations are of only some models are shown for explanation purpose only. You TV may not be exactly the same as illustrated.
<AV-14F116>
MENU
CHANNEL
2
1
<AV-21C116>
MENU
CHANNEL
2
1
<AV-21D116>
MENU
CHANNEL
2
1
<AV-21V116>
VOLUME
EXIT
3
VOLUME
EXIT
3
VOLUME
EXIT
3
4
4
1 MENU button
• MENU
button
2 CHANNEL m buttons
• MENU m buttons
ON
TIMER
POWER
3 VOLUME m buttons
• EXIT from MENU buttons
4 Remote control sensor
5
6
8
5 ON TIMER lamp
The light is switched on while ON TIMER function is operating.
6 POWER lamp
When the Main power is on, the light is red.
POWER/
ON TIMER
7 POWER/ON TIMER lamp
When the Main power is on, the light is green. When ON TIMER function
4
7
8
is on, it is red.
8 Main power button 9 Not application
ON
POWER
TIMER
5
6
8
MENU
1
<AV-21B116>
MENU CHANNEL VOLUME
1
16
CHANNEL
2
2
VOLUME
EXIT
3
EXIT
3
POWER
ON TIMER
49
7
8
POWER
ON
TIMER
4 7 8
Using the buttons on the TV
Basic operation
• Check to make sure the CHILD LOCK function is set to “OFF”. When the CHILD LOCK function is set to “ON”, the TV cannot be operated using the front control buttons. For details, see “CHILD LOCK” on page 12.
1 Press CHANNEL M to turn the TV
on from standby mode.
2 Press CHANNEL M to select a
channel.
3 Press VOLUME M to adjust the
volume.
4To turn your TV off, press the Main
power button to turn off the TV’s main power.
To change the TV mode to the VIDEO mode:
• Select the VIDEO mode with the INPUT function in “MENU 1”.
Operating menus
You can operate functions in menus using the front control buttons on the TV.
1 Press MENU y to display a menu.
2 Press MENU y repeatedly to display
the menu you want to use.
3 Press MENU y to select the desired
function or item.
4 Press MENU M or VOLUME M to
carry out the desired operation.
For details, see the description for each function.
5 Press VOLUME M to turn the menu
display off.
To turn the sub-menu display off:
1 Press MENU y to select “EXIT”.
MANUAL FINE SKIP NO SOUND SYSTEM B/G EXIT
SELECT BY PR 3 VL PROGRAM BY -+ EXIT BY EXIT BY VOL-+
DISPLAY
2 Press VOLUME m to turn the display
off.
17
Troubleshooting
If there is no picture or the TV does not operate normally, make sure the problem isn’t due to the reasons indicated below. If the problem persists even after taking the measures indicated, please contact a service technician.
Cannot turn the TV on
•Press the Main power button on the TV.
• Connect the power cord to the AC outlet.
The screen turns blue
• Is the BLUE BACK function on? (see page 12.)
Remote control inoperable
•Replace the batteries. (see page 3.)
Buttons on front of the TV do not work
•Switch the CHILD LOCK function off. (see page 12.)
TV does not respond immediately
•Press the main power button on the TV to turn off the main power. Press the main power button again to turn on the TV. If the TV returns to a normal state, operation is normal.
The TV turns off suddenly
• Is the OFF TIMER function set to operate? (see page 9.)
• Is the AUTO SHUTOFF function on? (see page 12.)
•Have you not performed an operation for about two hours after the TV was switched on by the ON TIMER function? (see page 11.) If you don’t perform an operation within about two hours, the TV is automatically switched off for safety.
Poor sound
•Press the SOUND SYSTEM button to select another sound system. (see page 8.)
Poor picture
•Press the COLOUR SYSTEM button to select another colour system. (see page 8.)
•Adjust the picture settings. (see page 15.)
• Set the Picture mode to STANDARD. (see page 8.)
• If noise (snow) totally blocks out the picture, check the following.
-Have the TV and aerial been connected
properly?
- Has the aerial cable been damaged?
- Is the aerial pointing in the right direction?
- Is the aerial itself faulty?
• If the TV or aerial suffer interference from other equipment, stripes or noise may appear in the picture. Move any equipment which can cause interference away from the TV.
• If the TV or aerial suffer interference from signals reflecting from mountains or buildings, double-pictures (ghosting) will occur. Change the aerial’s direction or replace it with an aerial with better directionality.
• When a white and bright still image (such as a white dress) is displayed on the screen, the white part may look as if it is coloured. When the image disappears from the screen, the unnatural colours will also disappear.
The TV turns on suddenly
• Is the ON TIMER function set to operate? (see page 11.)
The TV channel changes suddenly
• Is the ON TIMER function set to operate? (see page 11.)
18
Specifications
MODEL
TV RF systems
Colour systems
Channel and frequencies
Power input
Power consumption
Screen size (measured diagonally)
Audio output (Rated power output)
Speakers
External input / output
Dimension (W x H x D) (mm)
Weight 21 kg 22 kg
Accessories
RF MODE
VIDEO MODE
AV-14F116 AV-21B116 AV-21C116 AV-21D116 AV-21V116
B/G , I , D/K
PAL, SECAM
PAL, SECAM, NTSC 3.58 MHz, NTSC 4.43 MHz
VHF low channel (VL) = 46.25 to 168.25 MHz VHF high channel (VH) = 175.25 to 463.25 MHz UHF channel (U) = 471.25 to 863.25 MHz *Receives cable channels in mid band (X to Z, S1 to S10),
super band (S11 to S20) and hyper band (S21 to S41)
AC 220 to 240 V, 50/60 Hz (operating AC 90 to 260 V, 50/60 Hz)
MAX 68 W
AVG 47 W
Picture tube 368.4 mm Visible area 335.4 mm
3W 3W 3W 3W 3W
(5 x 9) cm x 2 (5 x 9) cm x 2 (5 x 9) cm x 1 (5 x 12) cm x 2 (6.5 x 13) cm x 2
INPUT : VIDEO input (RCA), AUDIO input (RCA) OUTPUT : VIDEO output (RCA), AUDIO output (RCA) Headphone jack : stereo mini jack (3.5 mm diameter, sound is monaural)
462 x 340.5 x 375 mm 598 x 476 x476.7 mm 502 x 476.5 x 471.6 mm 598 x 468 x 478 mm 649 x 465.5 x 473.5 mm
10 kg 21 kg 22 kg
-
Remote control unit :
RM-C1121 x 1
- AA/R6/UW-3 dry cell battery x 2
- Matching aerial adapter x 1
-
Rod aerial x 1
MAX 100 W
AVG 65 W
Picture tube 546.9 mm Visible area 508 mm
-
Remote control unit :
RM-C1121 x 1
- AA/R6/UW-3 dry cell battery x 2
- Matching aerial adapter x 1
MAX 100 W
AVG 65 W
Picture tube 546.9 mm Visible area 508 mm
-
Remote control unit :
RM-C1121 x 1
- AA/R6/UW-3 dry cell battery x 2
- Matching aerial adapter x 1
MAX 90 W
AVG 60 W
Picture tube 546.9 mm Visible area 508 mm
-
Remote control unit :
RM-C1121x 1
- AA/R6/UW-3 dry cell battery x 2
- Matching aerial adapter x 1
MAX 100 W
AVG 65 W
Picture tube 546.9 mm Visible area 508 mm
-
Remote control unit :
RM-C1121 x 1
- AA/R6/UW-3 dry cell battery x 2
- Matching aerial adapter x 1
Design and specifications subject to change without notice.
19
20
SCHEMATIC DIAGRAMS
COLOUR TELEVISION
AV-21D116/B
CD-ROM No.SML200607
BASIC CHASSIS
CG4
COPYRIGHT © 2006 Victor Company of Japan, Limited.
No.YA396
2006/7
AV-21D116
/B
STANDARD CIRCUIT DIAGRAM
NOTE ON USING CIRCUIT DIAGRAMS
1.SAFETY
The components identified by the symbol and shading are critical for safety. For continued safety replace safety ciritical components only with manufactures recommended parts.
2.SPECIFIED VOLTAGE AND WAVEFORM VALUES
The voltage and waveform values have been measured under the following conditions.
(1)Input signal : Colour bar signal
(2)Setting positions of each knob/button and variable resistor
(3)Internal resistance of tester
(4)Oscilloscope sweeping time
(5)Voltage values
Since the voltage values of signal circuit vary to some extent according to adjustments, use them as reference values.
: Original setting position when shipped
: DC 20kΩ/V
: H
: V
: Othters
: All DC voltage values
20µs / div
5ms / div
Sweeping time is specified
3.INDICATION OF PARTS SYMBOL [EXAMPLE]
In the PW board
: R1209
R209
Type No indication
MM PP MPP MF TF BP
TAN
(3)Coils
No unit
Others
(4)Power Supply
Respective voltage values are indicated
(5)Test point
: Test point
(6)Connecting method
: Ceramic capacitor : Metalized mylar capacitor
: Polypropylene capacitor : Metalized polypropylene capacitor : Metalized film capacitor : Thin film capacitor : Bipolar electrolytic capacitor : Tantalum capacitor
: [µH]
: As specified
: B1
: 9V
: Connector
: Receptacle
: Only test point display
: Wrapping or soldering
: B2 (12V
: 5V
)
4.INDICATIONS ON THE CIRCUIT DIAGRAM
(1)Resistors
Resistance value
No unit : [Ω]
K M
Rated allowable power No indication : 1/16 [W]
Others : As specified
Type
No indication
OMR
MFR
MPR
UNFR
FR
Composition resistor 1/2 [W] is specified as 1/2S or Comp.
(2)Capacitors
Capacitance value
1 or higher : [pF]
less than 1
Withstand voltage
No indication : DC50[V]
Others : DC withstand voltage [V]
AC indicated
Electrolytic Capacitors
47/50[Example]: Capacitance value [µF]/withstand voltage[V]
: [k]
: [M]
: Carbon resistor
: Oxide metal film resistor
: Metal film resistor
: Metal plate resistor
: Uninflammable resistor
: Fusible resistor
: [µF]
: AC withstand voltage [V]
(7)Ground symbol
: LIVE side ground
: ISOLATED(NEUTRAL) side ground
: EARTH ground
: DIGITAL ground
5.NOTE FOR REPAIRING SERVICE
This model's power circuit is partly different in the GND. The difference of the GND is shown by the LIVE : ( ) side GND and the ISOLATED(NEUTRAL) : ( ) side GND. Therefore, care must be taken for the following points.
(1)Do not touch the LIVE side GND or the LIVE side GND and the ISOLATED(NEUTRAL) side GND simultaneously. if the above caution is not respected, an electric shock may be caused. Therefore, make sure that the power cord is surely removed from the receptacle when, for example, the chassis is pulled out.
(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL side GND or never measure with a measuring apparatus measure with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND and ISOLATED(NEUTRAL) side GND at the same time. If the above precaution is not respected, a fuse or any parts will be broken.
Since the circuit diagram is a standard one, the circuit and circuit constants may be subject to change for improvement without any notice.
NOTE Due improvement in performance, some part numbers show in the circuit diagram may not agree with those indicated in the part list. When ordering parts, please use the numbers that appear in the Parts List.
)
(No.YA396)2-1
CONTENTS
SEMICONDUCTOR SHAPES ......................................................................2-2
BLOCK DIAGRAM........................................................................................2-3
CIRCUIT DIAGRAMS....................................................................................2-5
MAIN PWB CIRCUIT DIAGRAM (1/3) ....................................................................................................... 2-5
MAIN PWB CIRCUIT DIAGRAM (2/3)(3/3) ................................................................................................ 2-7
PATTERN DIAGRAMS .................................................................................2-9
MAIN PWB PATTERN ................................................................................................................................ 2-9
VOLTAGE CHARTS ................................................................................... 2-11
WAVEFORMS ............................................................................................ 2-12
USING P.W. BOARD
PWB ASS'Y name AV-21D116/B
MAIN P.W. BOARD SCG-1539A-BK
SEMICONDUCTOR SHAPES
TRANSISTOR
BOTTOM VIEW FRONT VIEW TOP VIEW
CHIP TR
E C B
ECB
B
(G)E(S)C(D)
ECB
ECB
C
BE
IC
BOTTOM VIEW FRONT VIEW TOP VIEW
OUT E
IN
IN OUTE
1 N
1 N
CHIP IC
TOP VIEW
N
N
N
1
N
1
N
1
N
2-2(No.YA396)
BLOCK DIAGRAM
MAIN PWB(1/3, 2/3)
STB_PW
IC703
5V REG.& RESET
POWER LED
FRONT IN
REAR IN
VIDEO
AUDIO
VIDEO
AUDIO
TU001
TUNER
SCL/SDA
IF
IC702
MEMORY
Q102
IF AMP
MICRO COMPUTER
SCL/SDA
IC701
SF102
SAW FILTER
SAW
SCL/SDA
EXT RGB/YS
IC301
1CHIP DECODER
VIDEO IN
AUDIO IN
LED(TIM)
REMOCON
AUDIO OUT
R OUT
G OUT
B OUT
IC651
AUDIO AMP
TIMER LED
REMOCON RECEIVER
HEADPHONE
SPEAKER L
SPEAKER R
MAIN PWB(3/3)
Q351
R OUT
Q352
G OUT
Q353
B OUT
CRT
REAR OUT
VIDEO
AUDIO
AC IN
POWER SW
LF901
D901
IC921
POWER
REG.
T921
SW
TRANSF.
IC971
9V REG.
IC972
5V REG.
VIDEO OUT
AUDIO OUT
9V OUT
5V OUT
V OUT
H OUT
IC421
V OUT
Q521
H DRIVE
Q522
H OUT
DEF YOKE
(V)
(H)
T522
FBT
B1
EHV
SCREEN
FOCUS
2-4(No.YA396)(No.YA396)2-3
CIRCUIT DIAGRAMS
MAIN PWB CIRCUIT DIAGRAM (1/3) SHEET 1
R746
D655
*4
C664
100/16
D654
*7
D656
*4
C657
100/25
Q302
2SC3928A/QR/-X
BUFFER
C321
R503
6.8k
D303
SPEAKER
Y655
X
Y653
*
IC651
C656 1/50
BP
12p
CH
X302
D306
X
10
H_OUT 0
C501
R501
R502
IC301
NN5198K
DECODE
47/25
CN0S4
10/50
R656
8.2k
C665
.01
R657R658
2.2k2.2k
CH
C310
Y654
C655
220p
CN0S5
NC
*
AN5265
C663 .001
.01
C311
R665
1k
R313
10k
VOL
1k
R314
LINE_V
BP
.47/50
C312
0
R312
R666
100
C659
4.7/50
D653
*4
R654 22k
Q652
2SC3928A/QR/-X
R321
Q301
R323
10k
R327
4.7M
C313
3.3/50
C322
.027/25
R322
2.7k
X
R660 C654
15k 470/16
R653
330
C653
10/50
Q651
2SC3928A/QR/-X
C651
OPT
1.5k C314
BUFFER
2SA1530A/QR/-X
.047/25
SCG
SCG
SCG
-1535A
*
MN1873
IC701
287JJ1
QAU0447
TU001
-001
QAX0731
SF102
-001
QAX0642
CF161
-001Z
CF162
X
UN2212
Q103
-X
2SD601A
Q161
R668
5.6
QRT029J-5R6
D652 D651
*7 *4
R664
R652
1k
NRSA63J-102X
D301
*5
A_MUTE
AUDIO
R324
1k
C324
33/50
6.8k
A.PROT
A_GND
A_VCC
VIDEO
R163
2.2K
R325
C164
0.01
Y160
X
C161
0.01
R161
1K
CF161
R164
*
Q161
*
AMP
R165
22
1.2K 220
R162
R166 820
*
CF162
*
C165
C166
0.1
0.01
C658
220/25
R659
4.7
1/2W
C652 .047
R651
4.7k
LINE_A
.01
C315
100/16
Y301
x
Y302
0
C162
1500p
C317
C323
0.47/50
D102
Y160
R112
R114
R115
R117
R118
C109
C114
D705
R771
R773
Q710
Y001
Y002
K001
Y653
Y654
K701
K703
K704
CP701
Y705
/QR/-X
MA859
-T2
QUY153
-050Y
22
4.7K
2.2K
0
2.2K
NCB31HK
-472X
NCB31HK
-103X
LE22440
-T16
820
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
X
X
SCG
-1536A
-1539A
MN1873
MN1873
287JM
287JJ1
QAU0466
QAU0383
-001
-002
QAX0731
QAX0666
-001
-002
QAX0642
QAX0694
-001Z
-001Z
QAX0694
X
-001Z
UN2212
X
-X
2SC3928
2SD601A
A/QR/-X
/QR/-X
QUY160
MA859
-100Y
-T2
QUY160
X
-050Y
22 10
4.7K
X
2.2K
X
0
X
X2.2K
NCB31HK
X
-472X
NCB31HK
X
-103X
LG22440
LE22440
-T16
-T16
2.2K
820
1.2KX
*3
X
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160
-050Y
-050Y
QUY160
QUY160 QUY153
-050Y
-050Y
SCG
-1540A
-1542A
MN1873
MN1873
287JJ1
287JJ1
QAU0447
QAU0447
-001
-001
QAX0731
QAX0731
-001
-001
QAX0642
QAX0642
-001Z
-001Z
X
UN2212
UN2212
-X
2SD601A
2SD601A
/QR/-X
/QR/-X
MA859
MA859
-T2
-T2
QUY153
QUY153
-050Y
-050Y
22
4.7K
4.7K
2.2K
2.2K
0
2.2K
2.2K
NCB31HK
NCB31HK
-472X
-472X
NCB31HK
NCB31HK
-103X
-103X
LE22440
LE22440
-T16
-T16
820
820
X
X
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153
QUY153
-050Y
-050Y
QUY153 QUY153
-050Y
SCG
-1543A
MN1873 287JJ1
QAU0447
-001
QAX0731
-001
QAX0642
-001Z
X
X
UN2212
-X
-X
2SD601A
/QR/-X
MA859
-T2
QUY153
-050Y
22
22
4.7K
2.2K
0
0
2.2K
NCB31HK
-472X
NCB31HK
-103X
LE22440
-T16
820
X
X
X
X
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
QUY153
-050Y
-050Y-050Y
X
QSW0619-003Z
R711
OSD_R
S702
QSW0619-003Z
S701
R721
10k
R726
4.7k
Q710
.033
*
SW
R737
100k
1k
R725
X
C736
4.7k
R718
560
R707
560
C721
C713
S703
R728
1k
C730 .01
1k
R729
CH
.01
C717
180p
K701
680
R716
SDA1
D704
R773
C738
R734
R706
TIMER LED (ORANGE)
D705
*
X
X
560
R740
3.9k
X
C733
R708
C744
IC701
MICOM
X
1k
OSD_YS
.01
C734
R709
OSD_B
*
R772
820
Q708
*3 SW
R741
560
*
X
X
C735
R710
4.7k
4.7k
OSD_G
LH22440-T16
POWER LED
(RED)
D707
*4
X
C726
P_ON/OFF
X
R750
R719
C725
A_MUTE
1k
X
C732
VOL
X
R748
100
D706
C720
.01
3.58/OTH
R771
*
X
X
C731
.01
C718
C723
R749
4.7k
10k
R796
C712
.01
10k
A.PROT
QSW0619-003Z
S704
QSW0619-003Z QSW0619-003Z
R727
R731
R730
R736 82k
Y705
SCL1
C716
R715
CH
180p
*
C711 .01
680
15k*4.7k
C728 180p
CH
QAX0884-001
C710
100/16
10K
K703
*
*
K704
C729 180p
CH
5.6
L701
X701
QQL244J-5R6Z
S705
C709
.01
R738 R739 10k
CH
C722
100p
Q702
2SC3928A/QR/-X
SW
R714
4.7k
R720
4.7k
R713
4.7k
R712
4.7k
PIC_MUTE
REMOCON RECEIVER
C719 1/50
IC702
MEMORY
2SC3928A/QR/-X
R797
15k
2
IC704
GP1UM281QK
10k
Q703
SW
R742
C724 150p
C706
C701
.01
Q709
X
X
IC703
PIC_MUTE
D731
*4
FBP
C707
.01
MA3091/M/-X
C308
100/16
R306
0
PC701
R702
X
X
C708
C309
1000/10
LB
.01
J005
QNS0197-001
R662 R661
270 270
1/2W 1/2W
2SA1530A/QR/-X
R655
Y976
X
D305
1K4-T2
D501
*6
C504
V_OUT
R401
10k
C437
C401
.47
TF
CN0S3
QGA2501C5-04Z
R667
100
Q653
47k
D657
*4
X
C402
C503 C502
X
TF
10/50 .01
.1
C316
10/50
1/2W
QAX0860-001Z
R703
X
D701
X
R701
X
L78LR05E-MA
C705
470/16
CP701
56K
CP
*
3WOMR
R723
27
QRL039J-270
AFT
STB_PW
V_SYNC
R307
1.2k
SDA1
R308
1.8k
FRONT
REAR
REAR
OUT
MAIN PWB ASS'Y (1/3) SCG-1539A-BK
C119
C117
C107
.0047
2SC5397/CD/-T
.47/50
C120 120p
CH
R120
390
.22
TF
R326D302
C325
100*5
10/50
SF122 QAX0325-001 SAW FILTER
QQL244J-2R2Z
L101
C106
.0047
Q102
AMP
C105
.0047
R111
R112
R113
R159
BP
180k
R160
X
R158
X
180
C104 .0047
*
R110
2.7k
100
CF103
X
J006
AUDI O
IN
VIDEO
VIDEO
IN
AUDI O
VIDEO
AUDI O
J004
J003
J002
QNN0384-001
R802
75
C842
X
C806
470/16
Q804
2SC3928A/QR/-X
SW
220/16
C805
C841
1500p
R807
68
R815
1/2W
VIDEO
AUDIO
R810
QRG01GJ-560
Q803 KTC3199/YG/-T BUFFER
LINE_V
R806
270
1/2W
R816
C811
10/50
R817
LINE_A
680
4.7k
A_MUTE
C812
X
180
R811
3
1
56
220
1
Y161
QUY160-100Y
Y975
QUY160-150Y
Y001
*
Y002
*
NOTE) 1.Refer to the parts list for the part number of IC702.
R374
6.8K
OSD_YS
A_VCC
A_GND
STB_PW
5V
A_VCC
A_GND
STB_PW
X_RAY
X_RAY
P_ON/OFF
A.PROT
P_ON/OFF
A.PROT
FBP
FBP
H_VCC
H_VCC
H_OUT
H_OUT
V_OUT
V_OUT
2
2
V_SYNC
SCL1
V_SYNC
0
R301
C301
C341
680p
10/50
D341
C302
*4
4.7/50 R302
4.7k
SCL1
SDA1
9V
R341
3.3K
OSD_R
C365 1/50
C306
.01
ABL
OSD_G
OSD_B
C367
C366
1/50
1/50
BPBP
BP
C307
470/16
CN00T
QJL001-054426-E
MAIN PWB ASS'Y(3/3)
(CRT SOCKET)
R303
100
CN10T
R304
100
R305
100
8.2
L103
C303
10p
CH
X301
QAX0705-001Z
C112
47/25
QQL244K-8R2Z
SF102
*
SAW FILTER
C109
*
.47/50
C304
C113 .0047
TF
R118
C305
.47/50
*
Q103
5%
.01
220p
C326
C115
.01
220
X
L104
C114
*
C110
0
C111
X
R116
X
*
SW
C116
.01
C122
R121
SF101
X SAW FILTER
C121
.01
R114 R109
* 6 .8k
D102
*
R115R117
*
*
C108
X
32V
MAIN PWB(2/3) SHEET2
(No.YA396)2-5 2-6(No.YA396)
AFT
TU001
*
R102
8.2
L001
QQL244K-8R2Z
C003
x
C004
470/16
R001
C103
47/25
R103
10
CF102
X
3.58/OTH
X
C009
X
X
IC001
L002
IN
OUT
GND
C005
.1
TF
X
75
K001
*
D001
C002
.01
MTZJ33A-T2
X
C006
X
220
R002
220
R003
C007
R004
56k
IF
NC
C001
10/50
BTPS( 32)
LOCK
5V
BM
SDA
SCL
AS
BT
NC
AGC
C008
4.7/50
X
c21226001a.001_1/2
MAIN PWB CIRCUIT DIAGRAM (2/3),(3/3) SHEET 2
AC110V-AC240V
50Hz/60Hz
!
!
VA901
QAF0072-621
!
S901
!
F901
T3.15AL
QMF51E2-3R15-S
QCZ9071-102
R901
QRF104K-3R9
C904
!
.001
QCZ9054-102
C930
X
K901
*8
D933
MTZJ16C-T2
D921
*5
D925
*5
QCZ9071-102
QRZ9046-825Z
QSW0750-001
DEG RELAY
!
C991
400VAC
!
C992
QCZ9071-102
400VAC
D901
G2SBA60
C929 .01
QFKA2JK-103
R928
QRL039J-683
3WOMR
K902
*8
R933
4.7
1/2W
!
C993
400VAC
!
R991
8.2M
RY971
68k
DEG COIL
QGZ5003C1-02
!
CNDEG
Y904
QUY160-050Y
QUY160-050Y
Y905
R904
X
IC921
STR-W5753A/F5
!
TH901
QAD0121-9R0
QUY160-150Y
QCZ0364-681
C922
.1
D920
1SS133-T2
Y902
R906
100k
QRL029J-104
C931
C927
0.1
X
R929
D929
X
C932 220p
QRZ0237-R18
2WOMR
2kV
C924
4.7/50
R925
1M
R924 150K
D928
*7
QFLC1HJ-332Z
QFZ9073-224
QUY160-125Y
275VAC MF
QFZ9072-104
QCZ9054-102
R923
R921
1.8
1/2W
D927
C925 33/50
C926
3300p
!
C901
!
LF901
*
Y903
!
C910
C907
!
.001
100k
QRL029J-104
R922
1/2W
MTZJ36A-T2
3.9k
TF
MFAC275V
C905
!
.001
QCZ9054-102
C909
QEZ0476-127
R903
2WOMR
220
R934
68k
D931
*4
R935
1/2W
PW
CN0PW QGA7901F1-02
X
D930
FR107GT-T3
Q973
X
D973
X
!
T921
QQS0213-001
K943
*8
K942
*8
ERC30-02L38E
560p
QCZ0364-561
K941
*8
RU3AM-LFC4
R986
X
R987
X
D943
FR105GT-T3
C944
QCB32HK-222Z
D942
QEHR1EM-108Z
C941
2kV
D941
R985
X
C972
X
D974 R988
XX
C947
QCB32HK-222Z
CP981
ICP-N50-T
!
CP
CP
CP982
!
ICP-N75-T
C945
1000/25
Y961
QUY160-100Y
L943
4.7
QQL244J-4R7Z
1000/25
QETN1EM-108Z
C949 NDC31HJ-471X
L942
QQL244J-4R7Z
1000/25
QQL26AK-820Z
C942
100/160
QEZ0203-107
MAIN PWB(1/3) SHEET1
A_GND
STB_PW
LB
A_VCC
Y973
0
Q961
X
R961
R962
X
X
IC971
L7809CP
IC972
L7805CP
Q974
2SA966/OY/-T
SW
C971
R974
2.2k
R963
R964
X
Q962
X
R976
12
2WOMR
C976
220/25
R979
47
3WOMR
C978
220/25
R978
CN0S2
47k
R977
1.2k 1/2W
Q975
*3 SW
X
C948
470p
4.7
C946
L941
82
H_VCC
9V
P_ON/OFF
5V
Y972
X
R965
X
X
C961
X
X
C977
220/16
C979
220/10
R984
X
R983
X
D986
X
R982
X
Q982
X
SW
R981
X
D983
X_RAY
A.PROT
32V
D982
*4
*4
Q981
X
2SC3928A/QR/-X
SW
D985
X
C981
X
Q572
H_OUT
15K
SW
R980
V_SYNC
R524
R525
2WOMR
2WOMR
V_OUT
FBP
R421
4.7k
D424
C422
V_OUT
SW
Q402
2SC3928A/QR/-X
X
33
MTZJ7.5S-T2
R578
10k
C561
ABL
R422
X
R423
0
X
R424
0
R425
3.3k
X
QFLC2AJ-103Z
R443
1
1/2W
R436
C436
.33
82k
TF
D427
MTZJ27B-T2
Q401
DTC124ESA-T
V.NECK
C523
47/25
Q521
2SC2655/Y/-T
R531
R532
330
1k
C531
100/160
QEZ0203-107
D571
C572
47/25
D562
X
X
R566
R565
XX
C427
100/35
R426
0
C424
.01
D425
*4
C429
10/50
QQR1244-001
C529
MY
.0033/50
R573
QRT029J-1R5
R577
3.9K
X
LA78040N V.OUT
IC421
R453
3.3K
T501
R526
270
1/2W
MY
C526
.0082/50
QRL039J-681
QRT029J-1R5
R576
22k
1/2W
2SA1208/ST/Z1-T
C423
18p
C426
.001/50
MY
R441
8.2k
R432
1/2W
2SD2627-YB11
R530
X
R529
C530
R528
R574
R575
X
Q571
PROTECTORFBT
C562
D421 MTZJ75-T2
3.9
QRE121J-2R7Y
K421
*8
Q522
!
R521
56
1/2W
X
X
D561
X
X
C421
R442
R431
10k
10k
C433
4.7/50
QEHR1HM-475Z
C435
2200/25
R433
.0047
C528
X
D555
X
Y502
*
R571
2.2K 1/2W
C571
100/10
100/35
C430
R440
*
C582
Y501
D423
MY
C428
*6
*
!
SK351
R349
R369
D584
X
C581
.1
R582
TF
22K
R585
X
MTZJ20B-T2
R552
QRJ146J-2R2X
TP-47G/R
TP-47R/G
4.7K
X
R581
1.8k 1/2W
R583
39k
4.7/250
QNZ0536-002
TP-47B
D581
C554
!
SK351 QNZ0536-002
QUY160-050Y
K351
QQR0621-002Z
U
U
Y304
Y303
X
C352
B
G
R
FOCUS
TP-E
SCREEN
C351 .001
X
QCZ0121-102
!
R365
12k
2WOMR
L353
QUY160-050Y
Q353
2SC4212/Z1/
B-OUT
R353
150
R368
1.8k
R364
12k
2WOMR
Q352
R430
82k
10k
R429
C425
X
CN00T
R444
X
C525
1.25KV
QFZ0200-103
X
250V
C527
QFZ0197-564
L522
X
26V
D554 R554
1.5K
1/2W
MTZJ9.1B-T2
!
R551
1
1W
QRX029J-R47
C552
1000/35
QETM1VM-108
MAIN PWB ASS'Y(1/3)
C555
.1/100
D553
2SC4212/Z1/
G-OUT
R352
150
R367
1.8k
R345
CN10T
X
QJL001-054426
T
XXX
D351
D352
D353
MAIN PWB ASS'Y (3/3) (CRT SOCKET) SCG-1539A-BK
L551
*
FR556
MY
D551
C551
X
*5 X
C357
470/10
R346
R351
150
2SC4212/Z1/
FR
X
Q351
R-OUT
R363
12k
2WOMR
R366
1.8k
!
T522
*
FBT
QRZ0107-152Z
C356
390p
CH
R359
R356
330
L352
QUY160-050Y
R361
QRZ0107-152Z
C355
270p
R358
R355
330
L351
QUY160-050Y
R360
QRZ0107-152Z
C354
330p
R357
R354 330
QUY160-050Y
QJL001-044026
CN00U
QJL001-044026-E
D582
*5
47
47
R347
3.9K
47
C553
D552
R362
R348
X
*5
X
CH
CH
L354
CN10U
R584
QUY160-100Y
c21226002a.001_2/2
MAIN PWB ASS'Y (2/3) SCG-1539A-BK
Y503
X
ADJUSTMENT
CONNECTOR
CN0S1
QGA2501C5-05Z
!
DEF YOKE
CN0HV
QGZ5003C1-04
LF901
T522
L551
Y501
Y502
SCG
-1542A
QQR0673
-002
QQH0170
-001
QQLZ026
-320
QUY160
-050Y
-050Y
SCG
-1543A
QQR0673
-002
QQH0170
-001
QQLZ026
-320
QUY160
-050Y
-050Y
SCG
SCG
*
-1535A
QQR0527
-002
QQH0195
-002
QQLZ026
-300
QUY153
-050Y
QUY153
-050Y
SCG
SCG
-1536A
QQR0527
-002
QQH0195
-002
QQLZ026
-320
QUY160
-050Y
QUY160 QUY160
-1539A
QQR0527
-002
QQH0195
-002
QQLZ026
-320
QUY160
-050Y
QUY160
-050Y-050Y
-1540A
QQR0527
-002
QQH0195
-002
QQLZ026
-300
QUY153
-050Y
QUY153 QUY160
-050Y
2-8(No.YA396)(No.YA396)2-7
PATTERN DIAGRAMS
MAIN PWB PATTERN
()
W028
W229
R904
IC921
D927
R906
PW
TH901
D929
C927
Y904
C925
R903
C554
C552
C421
W106
R661
C423
D553
R4 30
R429
W175
R573
R574
R571
C553
R552
C581
D552
R585
D581
W657
W016
D582
W017
FRONT
R582
R583
W605
W129
R581
FR556
C562
D561
C555
W548
C436
R443
W003
W087
W080
C427
90W5
D423
W635
C42 5
C426
R423
D424
W169
R421
R426
W176
R531
R436
R422
W011
W071
C551
IC421
R431
R441
R551
D551
D421
H001
R433
R432
R440
C424
C430
L522
K421
Y501
R529
C433
R442
W476
R444
R424
R453
C435
C422
R425
D427
W105
W495
D425
C429
Y503
T522
B1
Y502
C582 D555
C525
Q522
H002
W596
C527
W032
C528
R521
R530
R525
R532
C526
T501
C529
C523
Q521
R526
()
R528
C530
R524
R363
Q402
Q401
R349
R348
W338
W337
R367
D352
R347
D354
K351
D356
R358
W576
D353
R3 55
C355
R352
R345
C357
Q352
R361
R346
R351
TP-47G/R
R364
R357
L351
R360
52
L3
SCREEN
W336
C354
C352
R354
C351
W611
R366
Q351
TP-47R/G
R368
R356
D351
D355
Y304
Y303
SK351
R362
R359
C356
Q353
353
L353
R365
()
TOP
R
L354
TP-E
TP-47B
R369
Y001
W012
R003
C001
C653
W422
W631
D707
W041
W654
W136
D701
C007
W097
R659
Y655
Y654
TU001
Y002
R802
C008
W641
W099
C003
C664
C663
C659
C658
R652
W510
W632
W054
R004
R102
C002
W110
R303
W030
W214
R302
W069
C341
W159
W555
R301
W150
W072
C366
C365
W066
W655
W620
W623
W481
W505
C654
R741
W217
W114
W459
W113
W473
R726
W517
W112
W101
R719
12C7
W646
W4 45
W5
91
R746
R796
R748
R701
C732
R750
S702
C806
CF102
CF103
R103
R109
C109
Q103
R118
W544
C304
L103
C307
C3
01
C302
R305
R304
R306
W090
Y976
R308
C309
R401
C308
C5 02
C401
W479
W656
D501
W005
W618
W155
R711
R7 18
R710
R707
R7
09
R708
R7 06
R734
C734
C7
C7
C725
33
C7
18
C726
20
R749
D706
Q708
R740
C744
C731
S703
W524
R727
C106
C104
C108
R501
Q702
35
W423
W523
C842
C503
C7
S704
R806
C305
W092
C437
C316
D731
L1 01
R116
C306
R797
C7 36
R737
W601
J002
C805
Q804
SF102
R815
R817
R816
R811
C811
R115
Y161
C121
C110
SF122
C122
C120
C117
R121
C115
C116
R160
64
R1
C162
C164
C166
W168
C315
R321
W231
R314
R313
C310
Q301
Y3 02
Y301
W626
W604
W174
R307
Y972
Y973
W616
W617
W436
C812
W580
W424
R158
C119
R120
R159
D302
C165
R163
R1
65
R166
Q161
C161
R1
CF161
61
D301
W130
C323
W220
R323
W502
W206
D584
D341
W615
R341
W579
R3 26
W095
W124
C325
W482
W472
Y160
R162
W494
W588
W451
R324
W504
R736
W247
W645
R584
W137
CF162
C324
R325
W613
Y975
W612
C708
L701
W431
C711
C710
W474
K703
W496
C709
C705
IC703
C706
C707
W429
IC702
R712
R713
J006
CP701
J004
W413
C841
Q803
R807
R810
C103
C105
R113
R110
Q102
C107
R112
R111
D102
R114
W602
D303
D306
16
K701
C717
C504
R738 R739
C730
C112
IC301
W120
R729
C114
C716
C113
C312
C311
Y705
C321
R715R7
C713
R117
SF101
L104
C314
C317
C326
R327
D305
R312
Q302
R3
22
C313
C322
C402
C724
R742
R714
R720
W432
X7 01
R725
C7
28
C729
IC701
K704
S705
R731
C111
C303
X301
X302
R503
C501
W117
W628
C723
Q703
C722
C721
R728
R721 R730
CL003
A
RY971
C993
C949
L941
W543
C942
D942
K942
C944
R978
Q974
R976
R977
W652
R986
D974
R988
Q973
C976 R502
R987
73
D9
C991
CL005
FC901
Q710
R772
IC704
C719
K943
K941
R985
C 9 4 1
C945
CP982
W563
IC971
R981
C946
R965
W103
H004
C972
IC972
Q982
D941
D943
L942
Q975
C961
CP981
C947
R984
W466
R9 61
R962
R963
D986
L943
W648
R983
D985
C948
W164
R974
C971
Y961
W014
C981
W566
R964
Q981
R982
W578
S2
Q961
Q962
R657
W111
R668
W053
R980
C005
R002
C006
C004
D001
L002
L001
W098
K001
C009
IC001
R001
H006
R658
C656
R667
D654
R666
R660
C657
C367
D656
IC651
Q653
W204
R653
C652
R655
D657
W190
W188
C977
R979
C979
D983
D982
W148
W647
W173
R656
R654
W653
R723
W511
W526
C701
PC701
W483
W519
R374
W187
D653 R664
D652
W649
W184
D655
C655
C651
R703
R702
S3
Y653
C978
C738
C665
Q652
R665
Q651
R651
D651
Q709
S701
D921
R933
D925
D933
35R9
R925
C926
R929
W023
D931
R934
W329
C922
W049
T921
C924
R924
C932
D928
D920
W227
W228
W603
W061
K901
K902
D930
C930
C929
W062
D901
C904
C907
R901
R991
Y902
C992
8
2 9 R
C931
H003
R922
R923
R921
C905
C909
Y905
Y903
C910
LF901
VA901
C901
FC902
F901
S901
R771
D704
D705
R773
R578
Q572
W009
W162
W195
W196
W198
W199
J003
W094
W201
W077
W412
W411
W004
R575
C571
C531
Q571
R577
C572
R576
D571
L 5 5 1
W073
R565
R566
W640
C428
D562
D554
W638
W643
W644
C561
R554
W636
W154
W634
S5
S4
R662
J005
(No.YA396)2-9 2-10(No.YA396)
VOLTAGE CHARTS
<MAIN PWB>
MODE PIN NO.
IC301 1 0 2 4.4 3 6.3 4 3.4 5 0 6 5.0 7 5.0 8 5.5 9 9.0 10 3.0 11 3.0 12 3.0 13 0 14 2.8 15 4.2 16 9.0 17 3.8 18 2.8 19 2.8 20 0 21 0 22 0 23 4.4 24 3.2 25 3.0 26 3.5 27 4.2 28 3.7 29 4.1 30 3.9 31 4.2 32 4.2 33 9.0 34 4.0 35 4.7 36 4.0 37 6.1 38 4.2 39 4.3 40 2.7 41 6.2 42 1.0 43 3.7 44 3.9 45 1.2 46 3.1 47 5.4 48 5.0 49 0.7 50 0 51 4.4 52 0.7 IC421 1 3.7 2 26.0 3 2.0 4 0 5 13.8 6 26.3 7 3.7 IC651 1 12.5 2 5.6 3 0 4 2.4 5 9.4 6 9.6 7 0 8 9.7 9 19.9 IC701 1 4.5 2 4.9 3 0 4 0 5 0 6 4.9 7 4.9 8 2.3 9 3.0 10 4.9 11 0 12 0 13 2.4 14 0.1 15 1.8 16 1.8 17 0 18 0.8 19 0 20 4.9 21 4.9 22 4.9 23 4.9 24 2.3 25 4.9
DC (V
MODE
)
PIN NO.
26 0 27 4.1 28 4.9 29 0 30 0 31 0 32 0 33 0 34 4.9 35 4.7 36 4.9 37 4.4 38 4.4 39 4.9 40 0 41 2.1 42 0 IC702 1 0 2 0 3 0 4 0 5 4.9 6 4.9 7 0 8 4.9 IC703 1 14.4 2 5.8 3 0 4 4.9 5 4.9 IC704 1 4.5 2 4.9 3 0 IC921 1 314.0 2 NC 3 0 4 0 5 31.8 6 0 7 0.7 IC971 1 12.8 2 9.0 3 0 IC972 1 9.2 2 4.9 3 0 Q102 E 0 C 9.0 B 2.3 Q161 E 2.5 C 8.3 B 3.2 Q301 E 4.6 C 0 B 4.0 Q302 E 4.0 C 9.0 B 4.6 Q401 E 0 C 0 B 5.4 Q402 E 0 C 4.9 B 0 Q521 E 0 C 9.7 B 0.3 Q522 E 0 C 115.3 B 0 Q571 E 115.5 C 0 B 115.1 Q572 E 0 C 4.9 B 0
Q651 E 0 C 0.3 B 0
DC (V
MODE
)
PIN NO.
Q652 E 0 C 1.0 B 0.6 Q653 E 15.1 C 0 B 15.2 Q702 E 0 C 4.2 B 0 Q703 E 0 C 4.8 B 0.1 Q708 E 0 C 2.0 B 0 Q710 E 0 C 0.1 B 0 Q803 E 0 C 8.1 B 4.7 Q804 E 0 C 0 B 0.1 Q974 E 15.3 C 15.1 B 0 Q975 E 0 C 0.1 B 4.3 TU001 1 4.6 2 NC 3 0 4 4.4 5 0 6 4.5 7 4.9 8 0 9 31.3 10 NC 11 0
DC (V
<CRT SOCKET PWB>
MODE
)
PIN NO.
Q351 E 2.5 C 125.8 B 3.2 Q352 E 2.6 C 123.3 B 3.3 Q353 E 2.5 C 128.5 B 3.2
DC (V
)
(No.YA396)2-11
WAVEFORMS
-MAIN PWB-
(SHEET1) IC301-10
IC301-11
(H)
(H)
IC301-12
(H)
IC301-14
(1µs)
IC301-36
(H)
IC301-40
(1µs)
IC301-42
(H)
3.5 Vp-p
IC301-46
2.5 Vp-p
(SHEET2) IC421-1
0.6 Vp-p
Q522-B
2.0 Vp-p
(V)
(V)
(H)
IC701-27
5.0 Vp-p
IC421-3
T522-1
1000 Vp-p
3.5 Vp-p
30 Vp-p
(H)
(V)
(H)
4.0 Vp-p
IC701-35
5.0 Vp-p
IC421-5
60 Vp-p
T522-3
55Vp-p
(V)
(V)
(H)
IC421-6
T522-5
0.35 Vp-p
30 Vp-p
220 Vp-p
(V)
(H)
Q521-C
T522-7
3.0 Vp-p
38 Vp-p
25 Vp-p
(H)
(H)
Q521-B
T522-9
0.5 Vp-p
1.5 Vp-p
220Vp-p
(H)
(H)
Q522-C
2.5 Vp-p
(H)
1000Vp-p
-CRT SOCKET PWB-
(SHEET2) Q351-C Q352-C Q353-C
110 Vp-p
(H)
120 Vp-p
2-12(No.YA396)
(H) (H)
120 Vp-p
Victor Company of Japan, Limited Display Category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan
(No.YA396)
Printed in Japan
VPT
PARTS LIST
CAUTION
J The parts identified by the symbol are important for the safety . Whenever replacing these parts, be sure to use specified ones to secure the
safety.
J The parts not indicated in this Parts List and those which are filled with lines --- in the Parts No. columns will not be supplied.
J P.W. BOARD Ass'y will not be supplied, but those which are filled with the Parts No. in the Parts No. columns will be supplied.
ABBREVIATIONS OF RESISTORS, CAPACITORS AND TOLERANCES
RESISTORS CAPACITORS
CR Carbon Resistor C CAP. Ceramic Capacitor
FR Fusible Resistor E CAP. Electrolytic Capacitor
PR Plate Resistor M CAP. Mylar Capacitor
VR Variable Resistor CH CAP. Chip Capacitor
HV R High Voltage Resistor HV CAP. High Voltage Capacitor
MF R Metal Film Resistor MF CAP. Metalized Film Capacitor
MG R Metal Glazed Resistor MM CAP. Metalized Mylar Capacitor
MP R Metal Plate Resistor MP CAP. Metalized Polystyrol Capacitor
OM R Metal Oxide Film Resistor PP CAP. Polypropylene Capacitor
CMF R Coating Metal Film Resistor PS CAP. Polystyrol Capacitor
UNF R Non-Flammable Resistor TF CAP. Thin Film Capacitor
CH V R Chip Variable Resistor MPP CAP. Metalized Polypropylene Capacitor
CH MG R Chip Metal Glazed Resistor TAN. CAP. Tantalum Capacitor
COMP. R Composition Resistor CH C CAP. Chip Ceramic Capacitor
LPTC R Linear Positive Temperature Coefficient Resistor BP E CAP. Bi-Polar Electrolytic Capacitor
CH AL E CAP. Chip Aluminum Electrolytic Capacitor
CH AL BP CAP. Chip Aluminum Bi-Polar Capacitor
CH TAN. E CAP. Chip Tantalum Electrolytic Capacitor
CH AL BP E CAP. Chip Tantalum Bi-Polar Electrolytic Capacitor
RESISTORS
FGJ KMNRHZ P
±1% ±2% ±5% ±10% ±20% ±30%
+30%
-10%
+50%
-10%
+80%
-20%
+100%
-0%
(No.YA396)3-1
CONTENTS
USING P.W. BOARD & REMOTE CONTROL UNIT ................................................................................................... 3-3
EXPLODED VIEW PARTS LIST -1 ............................................................................................................................. 3-3
EXPLODED VIEW -1 ................................................................................................................................................... 3-4
PRINTED WIRING BOARD PARTS LIST ................................................................................................................... 3-5
MAIN P.W. BOARD ASS'Y (SCG-1539A-BK) ................................................................................................... 3-5
REMOTE CONTROL UNIT PARTS LIST (RM-C1121-1H) ........................................................................................ 3-8
PACKING ..................................................................................................................................................................... 3-8
PACKING PARTS LIST ............................................................................................................................................... 3-8
3-2(No.YA396)
USING P.W. BOARD & REMOTE CONTROL UNIT
P.W.B ASS'Y AV-21D116/B
MAIN P.W.B SCG-1539A-BK
REMOTE CONTROL UNIT RM-C1121-1H
EXPLODED VIEW PARTS LIST -1
Ref.No. Part No. Part Name Description Local
V01 A51LZM10X06AN25 PICTURE TUBE(ITC) Inc.DEF YOKE, PC MAGNETL01 QQW0006-001 DEG COILT522 QQH0195-002 FB TRANSF
1 LC11129-037A-H FRONT CABINET
2 GG40023-001A-H JVC MARK 3 GG30020-001A-H E.E.WINDOW 4 GG30019-003A-H POWER KNOB 5 CM35235-003-H SPRING 6 GG20006-003A-H CONTROL KNOB 7 GG30021-002A-H LED LENS 11 QYSBSFG4016ZA TAP SCREW M4 x 16mm(x7) 12 QYSBSF3010ZA TAP SCREW M3 x 10mm
13 GG10130-019B-H REAR COVER 14 CM47005-A01-H POWER CORD CLAMP 15 QMPR420-165-K2 POWER CORD 1.65m BLACK
16 A48457-3-H SPRING 17 WJY0008-006A-E BRAIDED ASS'Y 18 CM36623-003-H CHASSIS RAIL (x2) 19 QYSBSF4012ZA TAP SCREW M4 x 12mm(x8) 20 QAS0086-001 SPEAKER (x2) SP01,SP02
30 SCG-1539A-BK MAIN PWB
(No.YA396)3-3
EXPLODED VIEW -1
V01
6
1
7
20
L01
19
14
17
18
15
16
20
CRT SOCKET PWB
30
(Within MAIN PWB)
19
2
T522
30
MAIN PWB
3
5
4
3-4(No.YA396)
13
11
RATING LABEL
12
PRINTED WIRING BOARD PARTS LIST
MAIN P.W. BOARD ASS'Y (SCG-1539A-BK)
Ref No. Part No. Part Name Description Local
IC301 NN5198K IC IC421 LA78040N IC IC651 AN5265 IC IC701 MN1873287JM IC IC702 ATE08-21YMG6 IC (SERVICE) IC703 L78LR05E-MA IC IC704 GP1UM281QK IR DETECT UNIT 38kHz IC921 STR-W5753A/F5 IC IC971 L7809CP IC IC972 L7805CP IC
Q102 2SC5397/CD/-T TRANSISTOR Q161 2SC3928A/QR/-X TRANSISTOR Q301 2SA1530A/QR/-X TRANSISTOR Q302 2SC3928A/QR/-X TRANSISTOR Q351 2SC4212/Z1/ TRANSISTOR Q352 2SC4212/Z1/ TRANSISTOR Q353 2SC4212/Z1/ TRANSISTOR Q401 DTC124ESA-T DIGI TRANSISTOR Q402 2SC3928A/QR/-X TRANSISTOR Q521 2SC2655/Y/-T TRANSISTOR
Q522 2SD2627-YB11 POW TRANSISTOR Q571 2SA1208/ST/Z1-T TRANSISTOR Q572 2SC3928A/QR/-X TRANSISTOR Q651 2SC3928A/QR/-X TRANSISTOR Q652 2SC3928A/QR/-X TRANSISTOR Q653 2SA1530A/QR/-X TRANSISTOR Q702 2SC3928A/QR/-X TRANSISTOR Q703 2SC3928A/QR/-X TRANSISTOR Q708 UN2212-X DIGI TRANSISTOR Q710 UN2212-X DIGI TRANSISTOR Q803 KTC3199/YG/-T TRANSISTOR Q804 2SC3928A/QR/-X TRANSISTOR Q974 2SA966/OY/-T TRANSISTOR Q975 UN2212-X DIGI TRANSISTOR
D001 MTZJ33A-T2 Z DIODE D301 MTZJ9.1B-T2 Z DIODE D302 MTZJ9.1B-T2 Z DIODE D303 MA3091/M/-X Z DIODE D305 1K4-T2 SB DIODE D306 QRE121J-561Y C RESISTOR 560Ω 1/2W J D306 or QRE122J-561 C RESISTOR 560Ω 1/2W J D306 or QRG01GJ-561 OMF RESISTOR 560Ω 1W J D341 MA111-X SI DIODE D421 MTZJ75-T2 Z DIODE D423 1SR124-400A-T2 SI DIODE D425 MA111-X SI DIODE D427 MTZJ27B-T2 Z DIODE D501 MTZJ6.8C-T2 Z DIODE D551 FR105GT-T3 SI DIODE D552 FR105GT-T3 SI DIODE D553 MTZJ9.1B-T2 Z DIODE D554 MA111-X SI DIODE D571 MTZJ7.5S-T2 Z DIODE D581 MTZJ20B-T2 Z DIODE D582 FR105GT-T3 SI DIODE D651 MA111-X SI DIODE D652 MTZJ12C-T2 Z DIODE D653 MA111-X SI DIODE D654 MTZJ12C-T2 Z DIODE D655 MA111-X SI DIODE D656 MA111-X SI DIODE D657 MA111-X SI DIODE D704 LH22440-T16 LED POWER(RED) D705 LG22440-T16 LED ON TIMER(GREEN) D707 MA111-X SI DIODE D731 MA111-X SI DIODE D901 G2SBA60 BRIDGE DIODE D920 1SS133-T2 SI DIODE D921 FR105GT-T3 SI DIODE D925 FR105GT-T3 SI DIODE D927 MTZJ36A-T2 Z DIODE D928 MTZJ3.3A-T2 Z DIODE D930 FR107GT-T3 SI DIODE D931 MA111-X SI DIODE D933 MTZJ16C-T2 Z DIODE D941 RU3AM-LFC4 SI DIODE D942 ERC30-02L38E SI DIODE D943 FR105GT-T3 SI DIODE D982 MA111-X SI DIODE D983 MA111-X SI DIODE
Ref No. Part No. Part Name Description Local
C001 QETN1HM-106Z E CAPACITOR 10uF 50V M C002 NCB31HK-103X C CAPACITOR 0.01uF 50V K C004 QETN1CM-477Z E CAPACITOR 470uF 16V M C005 QFVF1HJ-104Z MF CAPACITOR 0.1uF 50V J C008 QETN1HM-475Z E CAPACITOR 4.7uF 50V M C103 QETN1EM-476Z E CAPACITOR 47uF 25V M C104 NCB31HK-472X C CAPACITOR 4700pF 50V K C105 NCB31HK-472X C CAPACITOR 4700pF 50V K C106 NCB31HK-472X C CAPACITOR 4700pF 50V K C107 NCB31HK-472X C CAPACITOR 4700pF 50V K C110 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J C112 QETN1EM-476Z E CAPACITOR 47uF 25V M C113 NCB31HK-472X C CAPACITOR 4700pF 50V K C115 NCB31HK-103X C CAPACITOR 0.01uF 50V K C116 NCB31HK-103X C CAPACITOR 0.01uF 50V K C117 QFVF1HJ-224Z MF CAPACITOR 0.22uF 50V J C119 QETN1HM-474Z E CAPACITOR 0.47uF 50V M C120 NDC31HJ-121X C CAPACITOR 120pF 50V J C121 NCB31HK-103X C CAPACITOR 0.01uF 50V K C122 NCB31HK-103X C CAPACITOR 0.01uF 50V K C161 NCB31HK-103X C CAPACITOR 0.01uF 50V K C162 NCB31HK-152X C CAPACITOR 1500pF 50V K C164 NCB31HK-103X C CAPACITOR 0.01uF 50V K C165 NCB31HK-103X C CAPACITOR 0.01uF 50V K C166 NCB31HK-104X C CAPACITOR 0.1uF 50V K C301 NCB31HK-123X C CAPACITOR 0.012pF 50V K C302 QETN1HM-475Z E CAPACITOR 4.7uF 50V M C303 NDC31HJ-100X C CAPACITOR 10pF 50V J C304 QFVF1HJ-474Z MF CAPACITOR 0.47uF 50V J C305 QETN1HM-474Z E CAPACITOR 0.47uF 50V M C306 NCB31HK-103X C CAPACITOR 0.01uF 50V K C307 QETN1CM-477Z E CAPACITOR 470uF 16V M C308 QETN1CM-107Z E CAPACITOR 100uF 16V M C309 NCB31HK-103X C CAPACITOR 0.01uF 50V K C310 NDC31HJ-221X C CAPACITOR 220pF 50V J C311 NCB31HK-103X C CAPACITOR 0.01uF 50V K C312 QENC1HM-474Z BP E CAPACITOR 0.47uF 50V M C313 QETN1HM-335Z E CAPACITOR 3.3uF 50V M C314 NCB31HK-103X C CAPACITOR 0.01uF 50V K C315 QETN1CM-107Z E CAPACITOR 100uF 16V M C316 QETN1HM-106Z E CAPACITOR 10uF 50V M C317 NCB31EK-473X C CAPACITOR 0.047uF 25V K C321 NDC31HJ-120X C CAPACITOR 12pF 50V J C322 NCB31EK-273X C CAPACITOR 0.027uF 25V K C323 QETN1HM-474Z E CAPACITOR 0.47uF 50V M C324 QETN1HM-336Z E CAPACITOR 33uF 50V M C325 QENC1HM-106Z BP E CAPACITOR 10uF 50V M C326 NCS21HJ-221X C CAPACITOR 220pF 50V J C341 QETN1HM-106Z E CAPACITOR 10uF 50V M C351 QCZ0121-102 C CAPACITOR 1000pF 3KV Z C354 NDC31HJ-331X C CAPACITOR 330pF 50V J C355 NDC31HJ-271X C CAPACITOR 270pF 50V J C356 NDC31HJ-391X C CAPACITOR 390pF 50V J C357 QETN1AM-477Z E CAPACITOR 470uF 10V M C365 QENC1HM-105Z BP E CAPACITOR 1uF 50V M C366 QENC1HM-105Z BP E CAPACITOR 1uF 50V M C367 QENC1HM-105Z BP E CAPACITOR 1uF 50V M C401 QFVF1HJ-474Z MF CAPACITOR 0.47uF 50V J C423 QCS32HJ-180Z C CAPACITOR 18pF 500V J C424 QFLC2AJ-103Z M CAPACITOR 0.01uF 100V J C426 QFLC1HJ-102Z M CAPACITOR 1000pF 50V J C427 QETN1VM-107Z E CAPACITOR 100uF 35V M C428 QETN1VM-107Z E CAPACITOR 100uF 35V M C429 QETN1HM-106Z E CAPACITOR 10uF 50V M C430 QFN32AJ-472Z M CAPACITOR 4700pF 100V J C433 QEHR1HM-475Z E CAPACITOR 4.7uF 50V M C435 QETM1EM-228 E CAPACITOR 2200uF 25V M C436 QFVF1HJ-334Z MF CAPACITOR 0.33uF 50V J C437 NCB31HK-104X C CAPACITOR 0.1uF 50V K C501 QETN1EM-476Z E CAPACITOR 47uF 25V M C502 NCB31HK-103X C CAPACITOR 0.01uF 50V K C503 QETN1HM-106Z E CAPACITOR 10uF 50V M C523 QETN1EM-476Z E CAPACITOR 47uF 25V M C525 QFZ0200-103 MPP CAPACITOR 0.01uF 1.5kV H C526 QFLC1HJ-822Z M CAPACITOR 8200pF 50V J C527 QFZ0197-564 MPP CAPACITOR 0.56uF 250V J C529 QFLC1HJ-332Z M CAPACITOR 3300pF 50V J C531 QEZ0203-107 E CAPACITOR 100uF 160V M C552 QETM1VM-108 E CAPACITOR 1000uF 35V M C554 QETN2EM-475Z E CAPACITOR 4.7uF 250V M C555 QFLC2AJ-104Z M CAPACITOR 0.1uF 100V J C571 QETN1AM-107Z E CAPACITOR 100uF 10V M C572 QETN1EM-476Z E CAPACITOR 47uF 25V M C581 QFVF1HJ-104Z MF CAPACITOR 0.1uF 50V J
(No.YA396)3-5
Ref No. Part No. Part Name Description Local
Ref No. Part No. Part Name Description Local
C652 NCB31HK-473X C CAPACITOR 0.047uF 50V K C653 QETN1HM-106Z E CAPACITOR 10uF 50V M C654 QETN1CM-477Z E CAPACITOR 470uF 16V M C655 QETN1HM-106Z E CAPACITOR 10uF 50V M C656 QENC1HM-105Z BP E CAPACITOR 1uF 50V M C657 QETN1EM-107Z E CAPACITOR 100uF 25V M C658 QETN1EM-227Z E CAPACITOR 220uF 25V M C659 QETN1HM-475Z E CAPACITOR 4.7uF 50V M C663 NCB31HK-102X C CAPACITOR 1000pF 50V K C664 QETN1CM-107Z E CAPACITOR 100uF 16V M C665 NCB31HK-103X C CAPACITOR 0.01uF 50V K C705 QETN1CM-477Z E CAPACITOR 470uF 16V M C706 NCB31HK-104X C CAPACITOR 0.1uF 50V K C707 NCB31HK-103X C CAPACITOR 0.01uF 50V K C708 QETN1AM-108Z E CAPACITOR 1000uF 10V M C709 NCB31HK-103X C CAPACITOR 0.01uF 50V K C710 QETN1CM-107Z E CAPACITOR 100uF 16V M C711 NCB31HK-103X C CAPACITOR 0.01uF 50V K C712 NCB31HK-103X C CAPACITOR 0.01uF 50V K C713 NCB31HK-103X C CAPACITOR 0.01uF 50V K C716 NDC31HJ-181X C CAPACITOR 180pF 50V J C717 NDC31HJ-181X C CAPACITOR 180pF 50V J C718 NCB31HK-103X C CAPACITOR 0.01uF 50V K C719 QETN1HM-105Z E CAPACITOR 1uF 50V M C720 NCB31HK-103X C CAPACITOR 0.01uF 50V K C721 NCB31EK-333X C CAPACITOR 0.033uF 25V K C722 NDC31HJ-101X C CAPACITOR 100pF 50V J C724 NDC31HJ-560X C CAPACITOR 56pF 50V J C728 NDC31HJ-181X C CAPACITOR 180pF 50V J C729 NDC31HJ-181X C CAPACITOR 180pF 50V J C730 NCB31HK-103X C CAPACITOR 0.01uF 50V K C744 NCB31HK-103X C CAPACITOR 0.01uF 50V K C805 QETN1CM-227Z E CAPACITOR 220uF 16V M C806 QETN1CM-477Z E CAPACITOR 470uF 16V M C811 QETN1HM-106Z E CAPACITOR 10uF 50V M C841 NCB31HK-152X C CAPACITOR 1500pF 50V K
C901 QFZ9073-224 MM CAPACITOR 0.22uF AC250V M
C904 QCZ9054-102 C CAPACITOR 1000pF AC250V Z
C905 QCZ9054-102 C CAPACITOR 1000pF AC250V Z
C907 QCZ9054-102 C CAPACITOR 1000pF AC250V Z C909 QEZ0476-127 E CAPACITOR 120uF
C910 QFZ9072-104 MM CAPACITOR 0.1uF AC250V K C922 QFLC1HJ-104Z M CAPACITOR 0.1uF 50V J C924 QETN1HM-475Z E CAPACITOR 4.7uF 50V M C925 QETN1HM-336Z E CAPACITOR 33uF 50V M C926 QFLC1HJ-332Z M CAPACITOR 3300pF 50V J C927 NCB31HK-104X C CAPACITOR 0.1uF 50V K C929 QFKA2JK-103 MM CAPACITOR 0.01uF 630V K C931 QCZ0364-681 C CAPACITOR 680pF 2kV K C932 NDC31HJ-221X C CAPACITOR 220pF 50V J C941 QCZ0364-561 C CAPACITOR 560pF 2kV K C942 QEZ0203-107 E CAPACITOR 100uF 160V M C944 QCB32HK-222Z C CAPACITOR 2200pF 500V K C945 QEHR1EM-108Z E CAPACITOR 1000uF 25V M C946 QETN1EM-108Z E CAPACITOR 1000uF 25V M C947 QCB32HK-222Z C CAPACITOR 2200pF 500V K C948 QETN1EM-108Z E CAPACITOR 1000uF 25V M C949 NDC31HJ-471X C CAPACITOR 470pF 50V J C976 QETN1EM-227Z E CAPACITOR 220uF 25V M C977 QETN1CM-227Z E CAPACITOR 220uF 16V M C978 QETN1EM-227Z E CAPACITOR 220uF 25V M C979 QETN1AM-227Z E CAPACITOR 220uF 10V M
C991 QCZ9071-102 C CAPACITOR 1000pF AC400V M
C992 QCZ9071-102 C CAPACITOR 1000pF AC400V M
C993 QCZ9071-102 C CAPACITOR 1000pF AC400V M
R002 NRSA63J-221X MG RESISTOR 220Ω 1/16W J R003 NRSA63J-221X MG RESISTOR 220 R004 NRSA63J-563X MG RESISTOR 56k R102 NRSA63J-750X MG RESISTOR 75 R103 NRSA63J-100X MG RESISTOR 10 R109 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R110 NRSA63J-272X MG RESISTOR 2.7k R111 NRSA63J-181X MG RESISTOR 180 R112 NRSA63J-100X MG RESISTOR 10Ω 1/16W J R113 NRSA63J-101X MG RESISTOR 100 R120 NRSA63J-391X MG RESISTOR 390Ω 1/16W J R121 NRSA63J-221X MG RESISTOR 220 R159 NRSA63J-184X MG RESISTOR 180kΩ 1/16W J R161 NRSA63J-102X MG RESISTOR 1k R162 NRSA63J-122X MG RESISTOR 1.2kΩ 1/16W J R163 NRSA63J-222X MG RESISTOR 2.2k R164 NRSA63J-221X MG RESISTOR 220 R165 NRSA63J-220X MG RESISTOR 22Ω 1/16W J R166 NRSA63J-821X MG RESISTOR 820Ω 1/16W J R301 NRSA63J-0R0X MG RESISTOR 0 R302 NRSA63J-472X MG RESISTOR 4.7k
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
R303 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R304 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R305 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R306 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R307 NRSA63J-122X MG RESISTOR 1.2kΩ 1/16W J R308 NRSA63J-182X MG RESISTOR 1.8kΩ 1/16W J R312 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R313 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R314 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R321 NRSA63J-152X MG RESISTOR 1.5kΩ 1/16W J R322 NRSA63J-272X MG RESISTOR 2.7kΩ 1/16W J R323 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R324 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R326 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R327 NRSA63J-475X MG RESISTOR 4.7MΩ 1/16W J R341 NRSA63J-332X MG RESISTOR 3.3kΩ 1/16W J R347 NRSA63J-392X MG RESISTOR 3.9kΩ 1/16W J R349 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R351 NRSA63J-151X MG RESISTOR 150Ω 1/16W J R352 NRSA63J-151X MG RESISTOR 150Ω 1/16W J R353 NRSA63J-151X MG RESISTOR 150Ω 1/16W J R354 NRSA63J-331X MG RESISTOR 330Ω 1/16W J R355 NRSA63J-331X MG RESISTOR 330Ω 1/16W J R356 NRSA63J-331X MG RESISTOR 330Ω 1/16W J R357 NRSA63J-470X MG RESISTOR 47Ω 1/16W J R358 NRSA63J-470X MG RESISTOR 47 R359 NRSA63J-470X MG RESISTOR 47 R360 QRZ0107-152Z C RESISTOR 1.5kΩ 1/2W K R361 QRZ0107-152Z C RESISTOR 1.5kΩ 1/2W K R362 QRZ0107-152Z C RESISTOR 1.5kΩ 1/2W K R363 QRL029J-123 OMF RESISTOR 12kΩ 2W J R364 QRL029J-123 OMF RESISTOR 12kΩ 2W J R365 QRL029J-123 OMF RESISTOR 12kΩ 2W J R366 NRSA63J-182X MG RESISTOR 1.8kΩ 1/16W J R367 NRSA63J-182X MG RESISTOR 1.8kΩ 1/16W J R368 NRSA63J-182X MG RESISTOR 1.8kΩ 1/16W J R374 NRSA63J-682X MG RESISTOR 6.8kΩ 1/16W J R401 NRSA02J-103X MG RESISTOR 10kΩ 1/10W J R421 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R423 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R424 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R425 NRSA63J-332X MG RESISTOR 3.3kΩ 1/16W J R426 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R429 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R430 NRSA63J-823X MG RESISTOR 82kΩ 1/16W J R431 NRSA02J-103X MG RESISTOR 10kΩ 1/10W J R432 QRE121J-3R9Y C RESISTOR 3.9Ω 1/2W J R433 QRE121J-2R7Y C RESISTOR 2.7Ω 1/2W J R436 NRSA63J-823X MG RESISTOR 82kΩ 1/16W J R440 QRE121J-471Y C RESISTOR 470Ω 1/2W J R441 NRSA63J-822X MG RESISTOR 8.2kΩ 1/16W J R442 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R443 QRE121J-1R0Y C RESISTOR 1Ω 1/2W J R453 NRSA63J-332X MG RESISTOR 3.3kΩ 1/16W J R502 NRSA63J-0R0X MG RESISTOR 0Ω 1/16W J R503 NRSA63J-682X MG RESISTOR 6.8k R521 QRE121J-560Y C RESISTOR 56Ω 1/2W J R525 QRL029J-330 OMF RESISTOR 33 R526 QRE121J-271Y C RESISTOR 270 R529 QRL039J-681 OMF RESISTOR 680Ω 3W J R531 NRSA63J-331X MG RESISTOR 330Ω 1/16W J R532 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J
R551 QRX029J-R47 MF RESISTOR 0.47Ω 2W J R552 QRJ146J-2R2X UNF C RESISTOR 2.2 R554 QRE121J-152Y C RESISTOR 1.5k R571 QRE121J-222Y C RESISTOR 2.2k R573 QRT029J-1R5 MF RESISTOR 1.5 R574 QRT029J-1R5 MF RESISTOR 1.5 R576 QRE121J-223Y C RESISTOR 22k R577 NRSA63J-392X MG RESISTOR 3.9k R578 NRSA63J-103X MG RESISTOR 10k R581 QRE121J-182Y C RESISTOR 1.8kΩ 1/2W J R582 NRSA63J-223X MG RESISTOR 22k R583 NRSA63J-393X MG RESISTOR 39k R651 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R652 NRSA63J-102X MG RESISTOR 1k R653 NRSA63J-331X MG RESISTOR 330Ω 1/16W J R654 NRSA63J-223X MG RESISTOR 22k R655 NRSA63J-473X MG RESISTOR 47kΩ 1/16W J R656 NRSA63J-822X MG RESISTOR 8.2k R657 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J R658 NRSA63J-222X MG RESISTOR 2.2k R659 QRE121J-4R7Y C RESISTOR 4.7 R660 NRSA63J-153X MG RESISTOR 15kΩ 1/16W J R661 QRE121J-271Y C RESISTOR 270Ω 1/2W J R662 QRE121J-271Y C RESISTOR 270 R664 NRSA63J-682X MG RESISTOR 6.8k
1/16W J
1/16W J
1/16W J
1/2W J
1/4W J
1/2W J
1/2W J
Ω Ω
1/2W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/16W J
1/2W J
1/2W J
1/16W J
2W J
2W J 2W J
3-6(No.YA396)
Ref No. Part No. Part Name Description Local
Ref No. Part No. Part Name Description Local
R665 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R666 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R667 QRE121J-101Y C RESISTOR 100Ω 1/2W J R668 QRT029J-5R6 MF RESISTOR 5.6Ω 2W J R706 NRSA63J-561X MG RESISTOR 560Ω 1/16W J R707 NRSA63J-561X MG RESISTOR 560Ω 1/16W J R708 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R709 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R710 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R711 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R712 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R713 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R714 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R715 NRSA63J-681X MG RESISTOR 680Ω 1/16W J R716 NRSA63J-681X MG RESISTOR 680Ω 1/16W J R718 NRSA63J-561X MG RESISTOR 560Ω 1/16W J R719 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R720 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R721 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R723 QRL039J-270 OMF RESISTOR 27Ω 3W J R725 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R726 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R727 NRSA63J-153X MG RESISTOR 15kΩ 1/16W J R728 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R729 NRSA63J-102X MG RESISTOR 1kΩ 1/16W J R730 NRSA63J-103X MG RESISTOR 10k R731 NRSA63J-472X MG RESISTOR 4.7k R736 NRSA63J-823X MG RESISTOR 82kΩ 1/16W J R737 NRSA63J-104X MG RESISTOR 100kΩ 1/16W J R738 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R739 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R740 NRSA63J-392X MG RESISTOR 3.9kΩ 1/16W J R741 NRSA63J-561X MG RESISTOR 560Ω 1/16W J R742 NRSA63J-563X MG RESISTOR 56kΩ 1/16W J R746 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R748 NRSA63J-101X MG RESISTOR 100Ω 1/16W J R749 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R771 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J R772 NRSA63J-821X MG RESISTOR 820Ω 1/16W J R773 NRSA63J-122X MG RESISTOR 1.2kΩ 1/16W J R796 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R797 NRSA63J-153X MG RESISTOR 15kΩ 1/16W J R802 NRSA63J-750X MG RESISTOR 75Ω 1/16W J R806 QRE121J-271Y C RESISTOR 270Ω 1/2W J R807 NRSA63J-680X MG RESISTOR 68Ω 1/16W J R810 QRG01GJ-560 OMF RESISTOR 56Ω 1W J R811 NRSA63J-221X MG RESISTOR 220Ω 1/16W J R815 QRE121J-181Y C RESISTOR 180Ω 1/2W J R816 NRSA63J-681X MG RESISTOR 680Ω 1/16W J R817 NRSA63J-472X MG RESISTOR 4.7kΩ 1/16W J R901 QRF104K-3R9 UNF WW RESISTOR 3.9Ω 10W K R903 QRL029J-104 OMF RESISTOR 100kΩ 2W J R906 QRL029J-104 OMF RESISTOR 100kΩ 2W J R921 QRE121J-1R8Y C RESISTOR 1.8Ω 1/2W J R922 QRE121J-221Y C RESISTOR 220Ω 1/2W J R923 QRZ0237-R18 UNF WW RESISTOR 0.18 R924 NRSA63J-154X MG RESISTOR 150kΩ 1/16W J R925 NRSA63J-105X MG RESISTOR 1M R928 QRL039J-683 OMF RESISTOR 68k R933 QRE121J-4R7Y C RESISTOR 4.7Ω 1/2W J R934 NRSA63J-683X MG RESISTOR 68kΩ 1/16W J R935 QRE121J-392Y C RESISTOR 3.9kΩ 1/2W J R974 NRSA63J-222X MG RESISTOR 2.2kΩ 1/16W J R976 QRL029J-120 OMF RESISTOR 12 R977 QRE121J-122Y C RESISTOR 1.2k R978 NRSA63J-473X MG RESISTOR 47k R979 QRL039J-470 OMF RESISTOR 47 R980 QRL029J-153 OMF RESISTOR 15k
R991 QRZ9046-825Z C RESISTOR 8.2MΩ 1/2W K
L001 QQL244K-8R2Z PEAKING COIL 8.2uH K L101 QQL244J-2R2Z PEAKING COIL 2.2uH J L103 QQL244K-8R2Z PEAKING COIL 8.2uH K L551 QQLZ026-320 COIL 32uH ±7% L701 QQL244J-5R6Z COIL 5.6uH J L941 QQL26AK-820Z CHOKE COIL 82uH K L942 QQL244J-4R7Z PEAKING COIL 4.7uH J L943 QQL244J-4R7Z PEAKING COIL 4.7uH J T501 QQR1244-001 DRIVE TRANSF
T921 QQS0213-001 SW TRANSF
CF161 QAX0694-001Z C FILTER 5.742MHz CF162 QAX0694-001Z C FILTER 5.742MHz
CP981 ICP-N50-T IC PROTECTOR 2.0A
CP982 ICP-N75-T IC PROTECTOR 2.7A
F901 QMF51E2-3R15-S FUSE 3.15A AC250V J002 QNN0384-001 PIN JACK
1/16W J
1/16W J
3W J
1/16W J
3W J
2W J
1/2W J
1/16W J
3W J
2W J
VIDEO,AUDIO IN/OUT (REAR)
J003 QNN0281-003 PIN JACK VIDEO IN(FRONT) J004 QNN0281-002 PIN JACK AUDIO IN(FRONT) J005 QNS0197-001 3.5 JACK HEADPHONE K351 QQR0621-002Z FERRITE BEADS K421 QQR1113-001Z FERRITE BEADS K901 QQR1113-001Z FERRITE BEADS K902 QQR1113-001Z FERRITE BEADS K941 QQR1113-001Z FERRITE BEADS K942 QQR1113-001Z FERRITE BEADS K943 QQR1113-001Z FERRITE BEADS
LF901 QQR0527-002 LINE FILTER S701 QSW0619-003Z PUSH SWITCH CH+ S702 QSW0619-003Z PUSH SWITCH CH­S703 QSW0619-003Z PUSH SWITCH VOL+ S704 QSW0619-003Z PUSH SWITCH VOL­S705 QSW0619-003Z PUSH SWITCH MENU
S901 QSW0750-001 PUSH SWITCH POWER SF102 QAX0666-002 SAW FILTER SF122 QAX0325-001 SAW FILTER
SK351 QNZ0536-002 CRT SOCKET
TH901 QAD0121-9R0 P THERMISTOR 9 TU001 QAU0466-001 TUNER
VA901 QAF0072-621 VARISTOR 620V X301 QAX0705-001Z CRYSTAL 4.433619MHz X302 QAX0860-001Z CRYSTAL 3.579545MHz X701 QAX0884-001 C RESONATOR 12.000MHz
LC30114-001C-H LED HOLDER
(No.YA396)3-7
REMOTE CONTROL UNIT PARTS LIST (RM-C1121-1H)
Ref No. Part No. Part Name Description Local
R56-1400 BATTERY COVER
PACKING
8
2
4 5 6 7
3
9
2
PACKING PARTS LIST
Ref.No. Part No. Part Name Description Local
1 GG10281-012A-H PACKING CASE 2 GG10296-001A-H CUSHION ASS'Y 4pcs in 1set 3 GG30097-003A-H POLY BAG 4 GG30096-001A-H POLY BAG 5 ------------ BATTERY AA/R6 1.5V(x2)
6 GGT0111-001A-H INST BOOK English,Thai
7 ATEAB001-00A MATCHING BOX 8 RM-C1121-1H REMOCON UNIT 9 GG30147-001B-H CORNER LABEL 2pcs in 1set
9
1
3-8(No.YA396)
Loading...