The components identified by the symbol and shading are
critical for safety. For continued safety replace safety critical
components only with manufactures recommende d parts.
2.SPECIFIED VOLTAGE AND WAVEFORM VALUES
The voltage and waveform values have been measured under the
following conditions.
(1)Input signal: Colour bar signal
(2)Setting positions of
each knob/button and
variable resistor
(3)Internal resistance of tester
(4)Oscilloscope sweeping time
(5)Voltage values
Sin ce th e vo l tage val ue s of si gn a l cir cui t va ry to some ex ten t
according to adjustments, use them as reference values.
: Original setting position
when shipped
:DC 20k
:H
:V
:Others
:All DC voltage values
/V
20µS/div
5mS/div
Sweeping time is
specified
3.INDICATIONS ON THE CIRCUIT DIAGRA M
(1)Resistors
Resistance value
No unit:[
K
M
Type
No indication
OMR
MFR
MPR
UNFR
FR
C ompos ition resistor 1/2 [W] is specifie d as 1/2S or Comp.
(2)Capacitors
Capacitance value
1 or higher:[pF]
less than 1
]
]
:[K
:[M]
:Carbon resistor
:Oxide metal film resistor
:Metal film resistor
:Metal plate resistor
:Uninflammable resi stor
:Fusible resistor
:[µF]
Withstand voltage
No indication :DC50[V]
Others:DC withstand voltage [V]
AC indicated
Electrolytic Capacitors
47/50[Example]:Capacitance value [µF]/withstand voltage[V]
Type
No indication:Ceramic capacitor
MM
PP
MPP
MF
TF
BP
TAN
(3)Coils
No unit
Others
4. N OTE FOR REPAIR ING SERVICE
This mode l's p ower circu it is pa rtly diffe rent in th e GND. The
difference of the GND is shown by the LIVE side GND and the
ISOLATED(NEUTRAL) side GND.Therefore, care must be
taken for the following points.
(1)Do not touch the LIVE side GND or the LIVE side GND and the
ISOLATED(NEUTRAL) side GND simultaneously. If the above
caution is not respected, an electric shock may be caused.
Therefore, make sure that the power cord is surely removed from
the receptacle when, for example, the chassis is pulled out.
(2)Do not short between the LIVE side GND and ISOLATED(NEUTRAL)
side GND or never measure with a measuring apparatus measure
with a measuring apparatus ( oscilloscope, etc.) the LIVE side GND
and ISOLATED(NEUTRAL) side GND at the same time.
If the above precaution is not respected , a fuse or any parts will be broken.
Since the circuit diagram is a standard one, the ci rcuit and
circuit constants may be subject to change for improvement
without any noti ce.
NOTE
Due improvement in performance, some part numbers show
in the circuit diagram may not agree with those i ndicated in
the part list.
When ordering parts, plea se use the numbers t hat appear
in the Parts List.
:AC withstand voltage [V]
:M etal ized mylar capa c i tor
:Polypropylene capacitor
:Metalized polypropylene capacitor
:Metalized film capacitor
:Thin film capacitor
:Bipolar electrolytic capaci tor
:Tant alum capacitor
µ
:[
H]
:As specified
2-4
No.51999
Apr. 2002 No. 51999
Page 3
AV14BJ8ENS / AV14BM8ENS
CRT
PLL/VST TUNER
UV1315/16
VIDEO PROCESSOR
STV2248C
+115V B+
CONTROLLER
ST92195
I
2
C
EEPROM
KEYPAD
IR
SENSOR
HP MODULE
AUDIO AMP
TDA 2822M
L
SMPS
UC3842
+12V
+8V
+5V
+5V STBY
IF
SCART1
FAV/BAV
HOR DRIVE
BU808DF
VER AMP
TDA8174AW
RGB AMP
BASE BOARD
FBT
VER. DEFL.
HOR. DEFL.
AUDIO
OUT
R
AV14BJ8EPS / AV14BM8EPS
AV14BJ8EES / AV14BM8EES
CONTENTS
AV14BJ8ENS / AV14BM8ENS
AV14BJ8EPS / AV14BM8EPS
AV14BJ8EES / AV14BM8EES
BLOCK DIAGRAM
SEMICONDUCTOR SHAPES
BLOCK DIA GRAM
DIFFERENCE LIST
CIRCUIT DIAGRAMS
MAIN PWB CIRCUIT DIAGRAM
HEADPHONE JACK PWB PWB CIRCUIT DIAGRAM
FRONT CONTROL PWB CIRCUIT DIAGRAM
FRONT AV JACK PWB CIRCUIT DIAGRAM
P ATTERN DIAGRAMS
MAIN PWB PATTERN
HEADPHONE JACK PWB PATTERN
FRONT CONTROL PWB PATTERN
FRONT AV JACK PWB PATTERN