JVC 0810YMH-AL-OT, GC-WP10, GCWP10AUS, GCFM2AUS User Manual

Download

HD MEMORY CAMERA

GC-FM2 GC-WP10

Waterproof with

Audio Recording

Detailed User Guide

Read this first

Before use, be sure to read “Safety Precautions” (P.2) and “Cautions” (P.3) to use the product correctly.

GC-WP10 is waterproof. Before use in water, be sure to read "Using the Camcorder in Water" (P.25).

ENGLISH

Safety Precautions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. (GC-FM2 only)

NOTES:

• The rating plate and safety caution are on the

bottom of the unit.

• The serial number plate is on the side of the

unit.

Do not point the lens directly into the sun. This can cause eye injuries, as well as lead to the malfunctioning of internal circuitry. There is also a risk of re or electric shock.

CAUTION!

The following notes concern possible physical damage to the camcorder and to the user. Do not use a tripod on unsteady or unlevel surfaces. It could tip over, causing serious damage to the camcorder.

CAUTION!

Connecting cables (Audio/Video etc.) to the camcorder and leaving it on top of the TV is not recommended, as tripping on the cables will cause the camcorder to fall, resulting in damage.

CAUTION:

The mains plug shall remain readily operable.

• Remove the mains plug immediately if the

camcorder functions abnormally.

WARNING:

The camcorder should not be exposed to excessive heat such as direct sunshine, re or the like.

— Read Before Use —

If this symbol is shown, it is only valid in the European Union.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water. (GC-FM2 only)

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

10. Only use attachments/accessories specied by the manufacturer.

11. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

12. Unplug this apparatus during lightning storms or when unused for long periods of time.

13. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Cautions

— Read Before Use —

Recording Medium

• Be sure to follow the guidelines below

to prevent corruption or damage to your recorded data.

- Do not bend or drop the recording medium, or subject it to strong pressure, jolts or vibrations.

- Do not splash the recording medium with water.

- Do not use, replace, or store the recording medium in locations that are exposed to strong static electricity or electrical noise.

- Do not bring the recording medium near objects that have a strong magnetic eld or that emit strong electromagnetic waves.

- Do not store the recording medium in locations with high temperature or high humidity.

- Do not touch the metal parts.

• When formatting or erasing data using

the camcorder, only the le administration information is changed. The data is not completely erased from the recording medium. If you want to completely erase all of the data, we recommend either using commercially available software that is specially designed for that purpose, or by physically destroying the camcorder with a hammer etc.

LCD Monitor

• To prevent damage to the LCD monitor,

DO NOT

... push it strongly or apply any shocks. ... place the camcorder with LCD monitor on the

bottom.

• To prolong service life

... avoid rubbing it with coarse cloth.

• Do not press the LCD monitor with a

sharp-pointed object or press against the surface of the LCD monitor with force when operating the touchscreen.

This may damage or break the LCD monitor. If you press the LCD monitor at the same time, it may cause a malfunction.

Main Unit

• For safety, DO NOT

... open the camcorder’s chassis. ... disassemble or modify the unit. ... allow inammables, water or metallic objects

to enter the unit.

... place naked ame sources, such as lighted

candles, on the apparatus.

... expose the apparatus to dripping or splashing.

(GC-FM2 only)

... insert any objects in the camcorder.

• Avoid using the unit

... in places subject to excessive humidity or

dust.

... in places subject to soot or steam such as near

a cooking stove.

... in places subject to excessive shock or

vibration. ... near a television set. ... near appliances generating strong magnetic

or electric elds (speakers, broadcasting

antennas, etc.). ... in places subject to extremely high (over 40 °C

or 104 °F) or extremely low (under 0 °C or

32 °F) temperatures.

• DO NOT leave the unit

... in places of over 50 °C (122 °F). ... in places where humidity is extremely low

(below 35%) or extremely high (above 80%). ... in direct sunlight. ... in a closed car in summer. ... near a heater. ... in high places such as on a T V. Leaving the unit

in high places while a cable is connected may

result in a malfunction if the cable is caught

and the unit falls onto the oor.

• To protect the unit, DO NOT

... allow it to become wet. (GC-FM2 only) ... drop the unit or strike it against hard objects. ... subject it to shock or excessive vibration

during transportation. ... keep the lens directed at extremely bright

objects for long periods. ... expose the lens to direct sunlight. ... swing it excessively when using the hand

strap. ... swing the soft camcorder case excessively

when the camcorder is inside it. ... store the camcorder in a dusty or sandy area.

• To prevent the unit from dropping,

- When using the camcorder with a tripod, attach the camcorder to the tripod securely.

If the camcorder drops, you may be injured and the camcorder may be damaged. When a child uses the unit, there must be parental guidance.

Cautions (Continued)

Battery

• When using the unit in a low temperature

environment (10°C (50°F) or below), the operating time may be shortened, or it may not function properly.

Keep the unit warm by keeping it in a pocket when using the unit out of doors in winter. (Do not expose the unit to heat directly such as a pocket warmer.)

• When you leave the unit unused for a long

period of time, run down the battery to prevent the battery from being depleted. (Leave the unit recording or playing until the unit is turned o automatically.)

Recharge the battery, and then run it down about every 6 months.

ATTENTION:

Remember that this camcorder is intended for private consumer use only.

Any commercial use without proper permission is prohibited. (Even if you record an event such as a show, performance or exhibition for personal enjoyment, it is strongly recommended that you obtain permission beforehand.)

Trademarks

The product you have purchased is powered by a rechargeable battery that is recyclable. Please call 1-800-8-BATTERY for information on how to recycle this battery. (USA and Canada only)

Waterproof Function (GC-WP10 only)

• Before using the camcorder in water, be

sure to read “Using the Camcorder in Water” (P.25) and to use the product correctly.

• Malfunction due to misuse by the customer is

not covered by warranty.

• Do not use this product in water deeper than

3 m (10 ft) or for longer than 30 minutes.

Video Function

• The unit records video in Mpeg-4 AVC/H.264

format for video and AAC (2ch) format (GCWP10: stereo, GC-FM2: monaural) for audio.

You cannot play back the recorded video using a component which does not support these formats.

Audio Function

• Audio cannot be played back on HD Media

Player CU-VS100/JVC.

• HDMI is a trademark of HDMI Licensing, LLC.

• Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United

States and/or other countries.

• Intel, Intel Core, and Pentium are trademarks or registered trademarks of Intel Corporation or its

subsidiaries in the United States and other countries

• Macintosh, QuickTime are registered trademark of Apple Inc. registered in the U.S. and other countries.

• Eye-Fi is a trademark of Eye-Fi, Inc.

• Other product and company names included in this instruction manual are trademarks and/or registered

trademarks of their respective holders.

Key features of camcorder

Full HD (1920 x 1080 / 30 fps) video recording

2. 3 inch touch screen

3. Electronic camera shake correction

4. Easy uploading to YouTube with the supplied software LoiLoScope EX

5. Eye-Fi card compatible: Uploading videos & still images via Wi-Fi network

6. iFrame video format recording (ideal for video editing with iMovie)

7. HDMI output connector

8. Waterproof design within 3 m/10 ft, 30 minutes (GC-WP10 only)

9. MP3 voice recorder (GC-WP10 only)

Daily Maintenance

Be sure to turn off the power and detach the cables before performing any maintenance.



Wipe this unit with a dry, soft cloth to remove any dirt.



When it is extremely dirty, soak the cloth in a solution of neutral

detergent, wipe the body with it, and then use a clean cloth to remove the detergent.

CAUTION

Camcorder

Lens/LCD Monitor



See page 27 for maintenance after recording in water. (GC-WP10 only)

Do not use benzene or thinner. (Cause of damage to or

•

malfunction of the unit)

When using a chemical cloth or other products, be sure to observe

•

the instructions of the product.

Do not leave the device in contact with rubber or plastic products

•

for a long time.



Use a lens blower (commercially available) to remove any dust, and a

cleaning cloth (commercially available) to wipe o any dirt. (Mold may form if the lens is left dirty.)



Perform [TOUCH SCREEN ADJUST] (P.45) if the reactive area of the screen

is misaligned with the touched area. (Adjust by lightly tapping with a corner of an SD card, etc. Do not press with an object with a sharp tip or do not press hard.)

Safety Precautions .....................................2

Cautions ......................................................... 3

Daily Maintenance ..................................... 5

Table of Contents ....................................... 6

Names and Functions of

Components ............................................ 7

Indications on LCD Monitor ....................8

Getting Started

Accessories .................................................11

Attaching the Core Filter to the

USB Cable ................................................11

Attaching the

Hand Strap

Inserting an SD Card ...............................12

Charging the Battery ...............................14

Using the Touchscreen ...........................16

Clock Setting ..............................................18

(GC-WP10 only)

....................11

Recording

Recording Video/Still Images ...............20

Useful Functions for Recording ...........23

Using the Camcorder in

Water (GC-WP10 only) ..................25

Playback

Playing Back on the Camcorder ..........28

Deleting Files .............................................30

Copying a Part in the

Video

(Trimming)

Viewing Files on TV ..................................32

......................................31

Audio Recording

Recording Audio

(GC-WP10 only)

.............33

Audio Playback

Playing Back Audio on the

Camcorder Delete Audio Files Copying a Part in the

Audio

(GC-WP10 only)

.....................34

(GC-WP10 only)

...............................38

...........37

Connecting with a Computer

Make a Backup on Computer...............39

Using the Supplied Software ...............40

Using an Eye-Fi Card................................42

Using the Menu ........................................44

Further Information

Troubleshooting .......................................46

Specifications .............................................49

Approximate Time/Number of

Recording ................................................50

Customer Support Information ..........52

Index .............................................................53

Names and Functions of Components

2

$ ( %

)

/ 0

GC-WP10

GC-FM2

LCD Monitor

Speaker

Power Button [ ]

SCREEN LOCK Button (P.26)

(GC-WP10 only)

Video/Still Image Select Button [ ]

(GC-WP10 only)

POWER/CHARGE Lamp

(

Recording Button (P.20)(GC-WP10 only)

)

Tripod Mounting Socket

Lens

Microphone

GC-WP10: Stereo GC-FM2: Monaural

AV Connector (P.32)

GC-WP10: also serves as Headphones Connector

SD Card Slot (P.12)

USB Connector (P.14, 39)

HDMI Mini Connector (P.32)

USB Connector Lever (GC-FM2 only)

(1): Push the connector out (2): Retract the connector

Press-and-hold the lever and slide

•

Cover

Indications on LCD Monitor

% &

(

+

% /

(

) )

Top Menu



Recording Mode Playback Mode

Video Recording Button (P.20)

Still Image Recording Button (P.20)

Audio Recording Button (P.33)

(GC-WP10 only)

Time

Play Select Button

Basic Settings Button (P.44)

(

Battery Indicator (P.15)

)

AC Adapter

When connected

When inoperative

When both of the Battery indicator and AC



adapter icons are displayed, the power is supplied through the both.

Video Recording Mode Select Button (P.21)

Video Playback Button

Still image Playback Button

Audio Playback Button (GC-WP10 only)

Recording Select Button

(

# $

% &

(

)

# $

(

)

+ ,

L R

During Recording



Videos

WIND CUT [ON] (P.45)

Headphones Volume Button

#

(GC-WP10 only)

AE Select Button (P.23)

(GC-WP10 only)

Recording Start/Stop Button

Menu Settings Button (P.44)

Play Select Button

(

Top Menu Button

)

Zoom Buttons

EFFECT (P.45)

Counter/Remaining Time

Still images

Menu Settings Button (P.44)

!

AE Select Button (P.23)

(GC-WP10 only)

Self Timer (10 Seconds/OFF) Select Button

Recording Button

Recording Direction Select Button (P.22)

Play Select Button

(

Top Menu Button

)

Zoom Buttons

EFFECT (P.45)

Remaining Number of Shots

Still images

Audio (GC-WP10 only)

Counter

Audio Recording Start/Stop Button (P.33)

Play Select Button

Top Menu Button

Microphone Input Level

Headphones Volume Buttons

(

Remaining Time

)

Audio Recording File Name

Audio

(GC-WP10 only)

! #

& ( ) *

(

)

Playback Index Screen



Videos/ Still Images

Video (MP4)/ Still Image (JPG)

Previous Page Button

Recorded Date

Recording Select Button

Eye-Fi SETTING Button (P.42, only when

using Eye-Fi card)

Zoom Display Button (P.28)

(

Delete Button (P.30)

)

Volume Button (P.28)

Top Menu Button

Next Page Button

Battery Indicator (P.15)

Recording Media

SD card

Next Date Button

Recorded Year

Previous Date Button

Audio

(GC-WP10 only)

Audio (GC-WP10 only)

Playback Operation

External File Button (P.36)

Delete Button (P.37)

Recording Select Button

Top Menu Button

Next Page Button

(

Previous Page Button

)

Volume Button (P.34)

File in Playback

Getting Started

Accessories

USB Extension Cable

(GC-FM2 only)Dedicated AV Cable

(P.12)

Hand Strap

(GC-WP10 only)

Core Filter

NOTE

You can use the hand strap

•

attached to the camcorder under water.

(Type A – Type B Mini)

USB Cable

(GC-WP10 only)

Optional accessory Page

AC adapter (AC-V10LU) (P.15)

SD card / SDHC card / SDXC card

Eye-Fi card (P.42)

Attaching the Core Filter to the USB Cable

GC-WP10: Attach the core filter to the USB cable. GC-FM2: Attach the core filter to the USB extension cable.

The core filter reduces noise generated when connecting the camcorder to an external component. Connect the end of the cable with the core filter to the camcorder.

Release the both stoppers.

To be connected

NOTE

• BesuretousetheUSBcableortheUSBextensioncablewiththecorefilterattached

when connecting the camcorder to the AC adapter or a computer.

to the camcorder.

Wind once.3 cm (1-3/16")

Attaching the Hand Strap

To guard against dropping the camcorder, we recommend attaching the hand strap.

NOTE

When carrying the camcorder, please be careful

•

not to drop it. Dropping it may cause injury or a malfunction of your camcorder.

When a child uses the camcorder, there must be

•

parental guidance.

(GC-WP10 only)

Getting Started

Inserting an SD Card

GC-WP10

Press the button( ) for about 1 second to turn off the camcorder.

The power lamp goes out.

Open the cover( ).

GC-FM2

Insert an SD card( ).

Turn off the power of this unit before inserting or removing a card.

Close the terminal cover( ) firmly.

To remove an SD card



Push the card inward once, then pull it out straight. Be sure to insert the SD card with the power turned off.

NOTE

To protect data, do not touch the terminals of the SD card.

•

Operations are confirmed on the following SD cards. (P.13)

•

Getting Started

Manufacturer Panasonic, TOSHIBA, SanDisk, ATP, Eye-Fi

Class 4 or higher compatible SD card (2 GB)

Video recording

Still image recording/ Audio recording

If other SD cards, SDHC cards or SDXC cards than the above are used, they may fail to

•

record data correctly, or they may lose data that had already been recorded.

The Eye-Fi card is a SD type memory card with built-in wireless LAN. You can transfer

•

videos and still images to a computer or the Web via the Eye-Fi card. (An Internet accessible environment and a wireless LAN router are separately required.) See page 42 to use an Eye-Fi card.

When your computer cannot recognize the SDXC card



Confirm and upgrade the OS of your computer.

Class 4 or higher compatible SDHC card (4 GB to 32 GB), or Class 4 or higher compatible SDXC card (48 GB to 64 GB) For ATP, only Class 4 or higher compatible SDHC card (up to 16GB)

SD card (256 MB to 2 GB), SDHC card (4 GB to 32 GB), or SDXC card (48 GB to 64 GB) For ATP, only SD card or SDHC card (up to 16GB)

Windows XP / Windows XP SP1

Windows XP SP2 / Windows XP SP3

Windows Vista

Mac OS Not compatible.

Not compatible. Necessary to upgrade to SP2 or higher.

Necessary to download the upgrade software. (KB955704) http://www.microsoft.com/downloads/details. aspx?FamilyID=1cbe3906-ddd1-4ca2-b727c2dff5e30f61&displaylang=en

Not compatible. Necessary to upgrade to SP1 or higher.

Getting Started

CHARGE STATUS

Charging the Battery

GC-WP10

Turn off the camcorder by pressing the button( ) for about

1 second.

The power lamp goes out.

Turn on the computer and connect to the camcorder( ).

GC-FM2

Charge Lamp

Charging Time Approx. 3 h

You can confirm the remaining battery level by touching the screen (for about 1 second) during charging. (You cannot confirm the level when the battery is extremely low.) When the charging is finished, disconnect the camcorder from the computer.

Blinks: Charging

Goes out: Charging finished

NOTE

The charging time is when the camcorder is charged at 25°C (77 °F).

•

If the battery is charged outside the room temperature range of 10 °C (50 °F) to 35 °C (95 °F), charging may take a longer time or it may not start. The recordable and playable time may also be shortened under some usage conditions such as at low temperature.

Charging is not possible while the camcorder is turned on.

•

Getting Started

The battery is not charged at the time of purchase. Charge before starting to use the

•

camcorder.

When the battery level is extremely low, the camcorder does not turn on until it is

•

charged even if it is connected to the computer or AC adapter.

Do not turn the computer off or into the sleep mode during charging (the charging

•

will stop).

With some types of computers, charging is possible even when the computer is

•

turned off. Refer to instruction manual of the computer or consult with the manufacturer of your computer.

You cannot record or play back video/still image/audio while the camcorder is

•

connected to a computer. You can record or play back video/still image/audio while the AC adapter is connected to the camcorder.

Indication when using the battery



Fully charged

Medium

Very low Recharge the battery at an early opportunity.

Indication when using the AC Adapter



(When connected)

(When inoperative)

When both of the Battery indicator and AC adapter icons are displayed, the power is supplied through the both.

Charging with the AC Adapter (optional)

Optional accessory: AC-V10LU/JVC

GC-WP10

GC-WP10 Connect with the AC adapter using the supplied USB cable.

GC-FM2

Connect the USB connector of this unit with the AC adapter. (You can connect also using the supplied USB extension cable.)

GC-FM2

Getting Started

Using the Touchscreen

The following are some examples.

Touch to Select

To select Video/Still Image/Audio on the Top Menu (Audio is for GC-WP10 only.)



Touch to return to the Top Menu and select the mode.

Recording



Touch to start/stop recording.

MEMO

The touchscreen of this unit is pressure-sensitive. When the touchscreen does not

•

respond smoothly, apply slightly more force to your fingertip.

Playback



Touch the thumbnail of the desired scene to play back.

Getting Started

To search for the desired scene



Press the page switching button ( ) or the date switching button ( ) to search for the desired scene.

MEMO

The touchscreen of this unit is pressure-sensitive. When the touchscreen does not

•

respond smoothly, apply slightly more force to your fingertip.

Do not press or rub with excessive force.

•

If you apply a protect sheet or a sticker, the touchscreen may not respond smoothly.

•

Do not operate the touchscreen using an object with a sharp or hard tip.

•

Touching two or more places at a time may cause a malfunction.

•

Perform [TOUCH SCREEN ADJUST] (P.45) if the reactive area of the screen is misaligned

•

with the touched area. (Adjust by lightly tapping with a corner of an SD card, etc. Do not press with an object with a sharp tip or do not press hard.)

Getting Started

SET DATE/TIME!

YES

RETURN QUIT

SET

CLOCK SETTING

Clock Setting

Press the button( ) for about 1 second to turn on the camcorder.

The power lamp turns on.

Touch [YES( )] when the [SET DATE/TIME!] screen appears.

Set the date and time( ).

Touch the month, day, year, hour and minute to select it.

•

Touch to make adjustments.

•

After setting the date and time, touch [SET].

•

Set the region where you live and touch [SAVE].

The city name and time difference are displayed.

Touch

To reset the clock



Set the clock with [CLOCK ADJUST] from the Basic Settings. (P.45)

Press the button to turn on the camcorder.

Touch on the top menu.

Touch [CLOCK ADJUST].

Touch [CLOCK SETTING].

The subsequent procedure is same as in the Steps

to make adjustments.

and 4 of “Clock Setting”.

Getting Started

NOTE

The [SET DATE/TIME!] screen does not appear when the date and time are already set.

•

The [SET DATE/TIME!] screen appears when the camcorder has not been used for a

•

long time. Charge the battery before setting the clock. (P.14)

When using this unit abroad, change the date and time display to the local time by

•

simply selecting your travel destination in [AREA SETTING]. (P.45)

Recording

Recording Video/Still Images

Before recording an important scene, it is recommended to conduct a trial recording.

Press the button( ) for about 1 second to turn on the camcorder.

Select video or still image mode( ) from the Top Menu.

When you turn on the power, the Top Menu appears only for the first time after purchasing the camcorder.

To return to the Top Menu, touch

during video or still image recording.

Start recording.

NOTE

After video recording for 12 consecutive hours, recording automatically stops.

•

For Videos

Touch the Recording START/STOP button( ).

Touch it again to stop recording. GC-WP10: You can make recording also with a press of the Recording button(

For Still Images

Touch the SNAPSHOT button( ).

To shoot continuously, keep touching the button. GC-WP10: You can shoot still image also with a press of the Recording button( To shoot in landscape mode, follow the same procedure.

Recording

For continuous video recordings of long consecutive hours, the file is split into pieces

•

automatically either in every 30 minutes or if the size exceeds 4 GB.

Using the AC adapter (optional), you can record for long consecutive hours.

•

To prevent the situation of forgetting to turn off the power, if this unit is not operated

•

for 5 minutes, the power is turned off automatically.

Brightness of the LCD monitor increases when recording in bright light. The LCD

•

monitor increases brightness when the AC adapter is connected to the camcorder. However, it returns to normal brightness when you do not operate the camcorer

during video recording for 5 minutes. ( / is displayed for about 3 seconds at the moment of switching.)

Change the Recording Quality ( video only)

Preparation: Video recording

Touch .

Select the recording quality.

HD 1080

HD 720

iFrame

QHD

Recording at Intervals (TIME-LAPSE RECORDING) (P.24)

•

When you place priority on Video Quality 1920 × 1080 / 30p

When you place priority on motion of the video 1280 × 720 / 60p

When you use the video in Apple iMovie '09 960 × 540 / 30p

When you make a long-duration recording 960 × 540 / 30p

Recording

Switching the Image Orientation ( Still Image Recording only)

Touch .

Image orientation can be changed to correspond to

Portrait

To use functions in landscape mode



Touch .

Select the function to use.

the camera’s orientation.

Touch

Landscape

Touch AE, Face Priority AE Switching (P.23)

SELF-TIMER

Menu Settings (P.45)

QUIT

Touch .

Quit.

NOTE

The size of still images differs between the portrait and the landscape modes.

•

Portrait mode: 2592 × 1944 (5M) Landscape mode: 1440 × 1920 (2.7M)

The image orientation do not switch automatically. Switch it according to the actual

•

orientation of the camcorder.

Video is not output through the AV cable when the Image Orientation is set to Portrait.

•

Video is not output at 480i or 480p through the HDMI cable when the Image

•

Orientation is set to Portrait.

Recording

Useful Functions for Recording

Adjusting the brightness based on the touched area (Touch AE)

Preparation: Video/ Still image

recording

Touch .

(GC-WP10 only)

With every touch, Touch AE and Face Priority AE alternate.

Touch the area to adjust.

With the touch, a frame appears in which exposure is adjusted.

The frame disappears if you touch the frame or if you use zoom function.

Shooting Human Subjects (Face Priority AE) (GC-WP10 only)

Preparation: Video/ Still image

recording

Touch .

With every touch, Touch AE and Face Priority AE alternate.

Frames appear on human faces in which exposure is automatically adjusted.

NOTE

Up to 16 frames on faces can be

•

displayed in total. You cannot choose the frame to adjust exposure arbitrarily.

Depending on the condition, faces may

•

not be detected.

If you cannot get proper effect, turn off

•

the Face Priority AE.

Recording

Recording at Intervals (TIME-LAPSE RECORDING)

This function enables the changes of a scene that occur slowly over a long period to be shown within a short time by taking frames of it at a certain interval.

Preparation: Video recording

Touch to display the Top

Menu and touch

Select a recording interval.

Touch the Recording START/

STOP button(

Recorded Time ( ) Actual Elapsed Time (

NOTE

Audio cannot be recorded during

•

time-lapse recording.

Zooming is not available in time-lapse

•

recording.

When recording is stopped with the

•

recorded time less than "0:00:00:17", the video will not be saved.

Recording stops automatically 99 hours

•

after it is started.

Make use of a tripod and optional AC

•

adapter for time-lapse recordings with long intervals. (optional: AC-V10LU/JVC)

The recording quality during time-lapse

•

recording is the same as that of HD 720 (P.50).

)

Recording interval/Playback speed

0.5 second/30 times

5 seconds/300 times

40 seconds/2400 times

Recording

Using the Camcorder in Water

After use in water, rinse the camcorder with fresh water, then wipe off and dry it well in a well-ventilated place out of direct sunlight as soon as possible. (P.27)

Before use



Confirm that there is no foreign material inside the terminal cover. (Foreign material causes ingress of water.)

Make sure that there is no damage to and no

•

foreign material (hair, lint, sand, dust, fluid etc.) adhered to the packing inside the cover, the SD card slot, or the parts around the connectors.

If you find damage, do Not use the unit.

•

Consult your JVC dealer or the nearest JVC service center.

Close the terminal cover firmly.

Close the cover firmly until it clicks into place.

•

Confirm that the red sign completely goes off.

•

(GC-WP10 only)

CAUTION

This camcorder is equipped with a waterproof function corresponding to JIS (Japanese

•

Industrial Standards) IPX8. This camcorder can make recordings in marine water and fresh water not deeper than 3 m (10 ft) or for not more than 30 minutes. (The waterproof capability is tested in accordance with JVC test standard and it does not assure damagefree or trouble-free operation. Waterproof function not evaluated by UL.)

Do not soak the camera in hot springs or water of 40 °C (104 °F) or higher.

•

Do not subject the camcorder to high water pressure such as in torrent or fall, or to

•

excessive pressure or impact such as by diving with the camcorder in hand.

The waterproof capability cannot be guaranteed if the camcorder is subject to impact

•

such as dropping. Consult with the dealer if the camcorder is subject to impact.

The camcorder sinks in water. Use the strap to prevent it from falling.

•

Open and close the cover in a dry place, after wiping moisture off the camcorder.

•

Wipe off immediately if such liquids as detergent solution, soap water, hot spring

•

water, bath agent, oil, sunscreen lotion or chemical liquid are spilled on the camcorder.

When used in water, at first, air bubbles may come out of the unit but it is not a

•

malfunction.

Recording

Press the button( ) for about 1 second to turn on the camcorder.

Select Video or Still Image mode( ) on the Top Menu.

Press the SCREEN LOCK button( ) for more than 1 second.

When using this unit in water, temporarily disable the touchscreen so that it will

•

not malfunction with the water pressure.

is displayed on the screen.

•

Press the Recording button(

•

Press the SCREEN LOCK button again, for more than 1 second, to turn off

•

and activate the touchscreen.

) to record.

To select video recording/still image recording in water



Pressing the button( ) will toggle the operation between Video Recording and Still Image Recording.

Audio recording is not selectable in water.

Recording

After use



After use in water or when dusted with sandy dust, rinse the camcorder with fresh water and dry it well as soon as possible.

Press the button for about 1 second to turn off the camcorder.

Make sure that the connector cover is closed tightly.

Rinse with fresh water.

Soak and wash in an appropriate depth of still fresh water in basin. Push aside the buttons to wash off the dirt in the gap. Do not rinse with chemicals, soap, neutral detergent or alcohol.

Do not apply current of water such as tap water directly to this unit.

D ry.

Wipe off with a dry soft cloth and dry in a well-ventilated place out of direct sunlight. There may be water near the microphone. Therefore, aim the camcorder downward and remove the water. Wiping with some sand remaining can cause a scratch. Wipe after rinsing the sand off. Also, wipe off strange materials and water drops inside the cover.

CAUTION

Do not dry with heat such as by using a hairdryer. The waterproof capability will deteriorate.

•

Do not leave the camcorder for long time in low temperature environment in cold

•

climates or in heat of 40 °C (104 °F) or higher (such as under sun light, in a sun-heated car or near the heater). The waterproof capability will deteriorate.

After use in marine water, soak in adequate amount of fresh water approximately 10

•

minutes and rinse with fresh water in order to clean off the salt.

Do not leave the camcorder soaked in or wet with salt water. It may cause corrosion,

•

tarnish, or deterioration of water resistance.

Remove the strap from camera and rinse the strap with fresh water.

•

Do not connect cables or charge with water drops remaining.

•

JVC cannot be held responsible of any loss of data due to ingress of water into the unit.

•

It is recommended to replace the packing (optional) once a year to maintain the

•

waterproof capability. Consult your nearest JVC service center. (P.52)

Playback

Playing Back on the Camcorder

Select a video or still image to play back from the index screen. Preparation: Video recording/ Still image recording

Touch .

The camcorder turns to play back mode.

Select a file.

Play back a file.

Touch the screen to display screen messages and operation buttons ( ).

(They will disappear if touched again.)

Operation modes ( )

Playback

Reverse playback

Pause

Forward search

Reverse search

Forward slow-motion

Reverse slow-motion

If you touch , the thumbnail images will enlarge.

Touch and drag the thumbnail display left and right or touch

to move to another page. If a shooting duration of still images

is within 2 seconds, they are displayed as one thumbnail (group).

Touch

Operation Buttons ( ) (P.29) Adjust the volume (

Touch +/– to make adjustments and touch

Video quality ( )

to stop playback.

)

to quit.

Playback

Operation Buttons (during Video



Playback)

Playback

Pause

Advances to the next video

Returns to the beginning of the scene

Forward search

Reverse search

Forward slow-motion

Reverse slow-motion

Operation Buttons (during Still



Image Playback)

Start slideshow

Stop slideshow

Advances to the next still image

Returns to the previous still image

Play back a group continuously

Repeated Playback of a Part (A-B Repeat)

Preparation: Video playback

Play back the video, then

touch

points.

With every touch, the setting toggles as shown below.

at the starting/end

Set starting point

Set end point

No setting (normal playback)

NOTE

A-B repeat is possible only within one

•

scene.

The setting is canceled if Stop is

•

selected after the end point is set.

Playback

Deleting Files

Preparation: Video/ Still image

playback

Touch .

Touch the video/still image

file to delete.

A check mark( ) appears on the selected video/still image.

If you touch the video/still image with a check mark, the selection is cancelled.

Touch [SEL ALL] to select all the video/still image files.

Touch [REL ALL] to cancel all the selection.

NOTE

You can delete the files by touching

•

during video/still image playback.

Touch [SET].

Touch [DELETE] when the

confirmation message

appears.

Playback

TRIMMING

QUIT

TRIMMING

SET QUIT

Copying a Part in the Video

Preparation: Video playback

Play back the video, then

touch

Pause playback at the

starting point and touch

Copy starting point ( )

Touch [YES] when the

NOTE

When you copy a part of the video, the

•

division point may not be accurate within a 1 second margin of error.

(Trimming)

confirmation message appears.

When copying finishes, the copied file is added to the index screen.

Resume playback, pause at

the end point and touch

Copy end point ( )

Touch [SET].

Playback

Yellow

Video Input

Audio Input (L)

Audio Input (R)

White

Red

HDMI Terminal Input

Viewing Files on TV

Preparation:

Turn on the TV.

•

Turn on the power( ) of the camcorder and select the playback mode.

•

To connect using the dedicated AV cable (provided)( )



To connect using the HDMI mini cable (optional)( )



Connect the camcorder to a TV.

Switch to the TV’s external input connector.

Start the playback. (P.28)

NOTE

Use the supplied AV cable. Otherwise, image and sound cannot be output.

•

If the AV cable or HDMI cable is disconnected during playback, the playback will be

•

paused. When an AV cable and an HDMI cable are connected, output to the HDMI cable is prioritized.

•

Also refer to instruction manual of the TV.

•

We recommend using the Category 2 HDMI cable (High Speed cable).

•

Insert the connector in the right direction. Forcing the connector into the terminal

•

may cause damage.

If you connect the camcorder using the AV cable, image is output only when playing

•

back video. If you connect the camcorder using the HDMI Mini connector, image is output when both playing back and recording video. However, if you connect the camcorder to a TV with 480p or 480i resolution, image is output only when playing back video.

Image is not output during the audio recording and audio playback.

•

Audio Recording

L R

Recording Audio

Press the button( ) for about 1 second to turn on the camcorder.

(GC-WP10 only)

Touch Audio mode( ) on the Top Menu.

To return to the Top Menu, touch in the audio recording screen.

Touch the Recording START/STOP button( ).

Audio recording starts. Touch again to stop audio recording.

NOTE

If you record audio 12 hours continuously, it will stop recording automatically.

•

Audio Playback

L R

Playing Back Audio on the Camcorder

You can select and play back the recorded audio from an index screen.

Preparation:

Touch the PLAY button.

Audio recording

Play back the audio.

Operation modes ( )

Playback

Pause

The camcorder turns to play back mode.

Select audio to play back.

Forward search

Reverse search

Adjust the volume ( )

Touch +/– to make adjustments and touch

to quit.

(GC-WP10 only)

Touch to move to another page.

To the recorded audio files, serial numbers 0001-9999 will be given.

Operation buttons ( )



Playback

Pause

Advances to the next audio

Returns to the beginning of the Audio currently playing

Forward search

Reverse search

Changes the playback order (Random Playback)

Touch

to return to the audio index screen.

Audio Playback

Repeated Audio Playback of a Part (A-B Repeat)

Preparation: Audio playback

Play back the audio, then

touch

points.

With every touch, the setting toggles as shown below.

at the starting/end

Set starting point

NOTE

A-B repeat is possible only within one

•

scene.

The setting is canceled if Stop or

•

Random Playback is selected after the end point is set.

Set end point

No setting (normal playback)

Audio Playback

[PICSIO_SD] [MUSIC] [1234]

[ABCDE]

SAMPLE.MP3

TEST.MP3

[ZZZ]

SOUND.MP3

Play External Audio Files

You can play audio files (MP3) recorded with other devices such as computer.

Preparation:

Touch on the audio index

screen.

Select audio to play back.

Touch to return to the normal audio playback.

NOTE

You can create up to 3 levels of folders

•

under [MUSIC].

You can create up to 50 subfolders per

•

folder.

You can create up to 999 files per folder.

•

Display of tags and the Album Art are

•

not supported.

Audio playback

Folders and files with double-byte

•

characters (such as Japanese) cannot be played.

Folders and files with more than

•

8 single-byte characters cannot be played. (You cannot edit file name with the camcorder. Use a computer and other devices to edit file names.

You cannot delete external audio files

•

with the camcorder.

You can play only stereo audio files.

•

You can play audio at 44.1 kHz and

•

48 kHz. (Playback of not all the files is guaranteed.)

You cannot play back Mpeg2 and

•

Mpeg2.5 audio files.

Structure of folders and files



Using computer or other devices, copy the audio to play back (folders and files) to an SD card under [MUSIC] folder.

Folders Files

The name is arbitrary (8 or less single-byte alphanumeric characters). The extension is [MP3].

The name is arbitrary (8 or less single-byte alphanumeric characters).

Audio Playback

SEL ALL REL ALL

SET

DELETE

Delete Audio Files

Preparation: Audio playback

Touch .

Touch the audio file to delete.

(GC-WP10 only)

Touch [SET].

Touch [DELETE] when the

confirmation message

appears.

NOTE

You can delete the files by touching

•

during audio playback.

You cannot delete external audio files.

•

A check mark appears on the selected audio.

If you touch the audio with a check mark, the selection is cancelled.

You can select all the audio files by touching [SEL ALL].

You can cancel all the selection by touching [REL ALL].

You can confirm the audio to play back by touching

Playback).

(Confirm

Audio Playback

TRIMMING

QUIT

TRIMMING

QUITSET

Copying a Part in the Audio

Preparation: Audio playback

Play back the audio file, then

touch

Pause playback at the

starting point and touch

Resume playback, pause at

Touch [SET].

Touch [YES] when the

(GC-WP10 only)

the end point and touch

Copy end point( ).

confirmation message appears.

When copying finishes, the copied file is added to the index screen.

Copy starting point ( ).

NOTE

The starting and end points of the

•

copied audio may not exactly match the selected points.

Connecting with a Computer

[PICSIO_SD] [DCIM]

[100JVCSO]

[101JVCSO]

[102JVCSO]

PIC_XXXX.MP4 PIC_XXXX.MP4 PIC_XXXX.JPG PIC_XXXX.JPG PIC_XXXX.MP3 PIC_XXXX.MP3

Make a Backup on Computer

Preparation: Turn on the camcorder and the computer.

You can save the recorded videos, still images or audio files on a computer.

Connect the camcorder to a computer.

See page 7 for the position of the USB connector on GC-FM2. If the camcorder is not charged, it will not turn on when connected to the

computer.

Windows: Double-click [PICSIO_SD] in [Computer] (or [My

Computer]).

Mac: Double-click [PICSIO_SD] on the desktop.

GC-WP10

Copy video/still image/audio files from the [DCIM] folder.

Videos

Still Image

Audio

To disconnect the camcorder from a computer (Windows)



Click the icon in the task tray on the computer screen.

The [Safely Remove Hardware] window appears.

Select [USB Mass Storage Device] and then click [Stop].

To disconnect the camcorder from a computer (Mac)



Drag and drop [PICSIO_SD] and [PICSIO_APP] on the desktop to the Trash. When they disappear from the desktop, disconnect the USB cable.

Connecting with a Computer

Using the Supplied Software

For Windows PC Users

You can edit videos and still images, or transfer them to iPod or the sharing site (YouTube, etc.) using the supplied software. (Please use another software for DVD or BD creation and buring.) Right click [Computer] (or [My Computer]) in the Start Menu, then select [Properties] and confirm the following items.

For Windows Vista/Windows 7



Windows Vista: Home Basic or Home Premium

(Pre-installed edition only for both) Windows 7: Home Premium (Pre-installed edition only)

Service Pack 2 (Windows Vista only)

Processor:

Intel Core 2 Duo CPU 2 GHz or higher Intel Core 2 Duo CPU 3 GHz or higher recommended Intel Core 2 Quad CPU 2 GHz or higher recommended

Memory: 2 GB or more

System type: 32 bit/64 bit

For Windows XP



Windows XP: Home Edition or Professional

(Pre-installed edition only for both)

Service Pack 3

Processor:

Intel Core 2 Duo CPU 2 GHz or higher Intel Core 2 Duo CPU 3 GHz or higher recommended Intel Core 2 Quad CPU 2 GHz or higher recommended

Memory: 2 GB or more

Other Conditions



Graphic:

NOTE

The system configuration described above is required in order to use the supplied

•

software.

Microsoft .NET Framework 3.5sp1 must be installed on your computer.

•

The camcorder is compatible to the graphic cards equipped with the playback

•

support function of H.264 video.

Intel 945 or later, NVIDIA Geforce 6000 series or later, ATI Radeon 9600 or later

Connecting with a Computer

To enable MultiTouch control, Windows 7 and the display compatible to MultiTouch is

•

required.

For details, consult with the manufacturer of your computer.

•

For details on hardware requirements and customer support information, refer to the

•

following web site. http://loilo.tv/product/15

To start the supplied software



Preparation:

Turn on the camcorder and the computer.

•

Connect the camcorder to the computer. (P.39)

•

[Auto Play] window appears.

If [Auto Play] window does not appear, double-click the [PICSIO_APP] icon in [My Computer] then double-click the LoiLoScope EX (LoiLoScopeEX.exe).

Select [LoiLoScope EX] and click [OK].

If [LoiLoScope EX] does not appear in the [Auto Play] window; select [Open folder to view files], click [OK] and double-click the LoiLoScope EX (LoiLoScopeEX.exe) icon in the window.

NOTE

For details about operations in LoiLoScope EX, see its Help.

•

For Mac Computer Users

You can import files from this unit to a computer using Apple's iMovie '09 (video) or iPhoto (still image). To verify the system requirements, select "About This Mac" from the Apple menu. You can determine the operating system version, processor and amount of memory.

For the latest information on iMovie or iPhoto, refer to the Apple website.

•

For details on how to use iMovie or iPhoto, refer to the help file of the respective

•

software.

There is no guarantee that the operations will work with all computer environments.

•

Connecting with a Computer

Using an Eye-Fi Card

What is Eye-Fi?



Eye-Fi is an SD memory card with wireless LAN function. Using an Eye-Fi card, you can transfer videos and still images to a computer or the web. (An Internet accessible environment and a wireless LAN router are separately required.) Use of Eye-Fi card may be illegal and prohibited in countries and regions where it has not been approved by competent authorities. Please contact Eye-Fi support for the details of approved countries and regions.

Types of cards



Product name Video Transfer Still Image Transfer

Eye-Fi Home/ Eye-Fi Share/ Eye-Fi Geo

Eye-Fi Share Video/ Eye-Fi Explore Video/ Eye-Fi Pro/ Eye-Fi Connect X2/ Eye-Fi Geo X2/ Eye-Fi Explore X2/ Eye-Fi Pro X2

Audio files cannot be transferred.

To use the Eye-Fi card



–



 

Make settings on the Eye-Fi card with Eye-Fi Center.

For how to install and operate the Eye-Fi Center, refer to its instruction manual.

Set the [Eye-Fi SETTING] to [ON] in the Basic Settings. (P.45)

When the [Eye-Fi SETTING] is set to [ON] recorded videos and still images are

•

automatically transferred. (The files already transferred earlier are not transferred again.)

To abort Eye-Fi transfer, turn off the camcorder or set the [Eye-Fi SETTING] to [OFF] in

•

the Basic Settings.

To transfer selected videos and still images, see page 43.

•

The Eye-Fi Center with the default setting transfers all videos/still images. Change the settings for the Eye-Fi Center beforehand to transfer selected videos/still images.

NOTE

You cannot transfer files during the recording mode, editing and formatting of the

•

card.

You cannot transfer video files larger than 2 GB. (as of July, 2010)

•

Depending on the connection conditions, transfer may be interrupted or take time long

•

due to passing the Eye-Fi server, even if it is displayed that the transfer has been completed.

Connecting with a Computer

TRANSFER SELECTION

SEL ALL REL ALL SET

TRANSFER SELECTION

SEL ALL REL ALL SET

We recommend using the AC adapter (optional: AC-V10LU/JVC) when transferring

•

files of large size.

If it doesn't operate properly, first confirm that the settings of the Eye-Fi card are

•

correct and try the data transfer using other equipment.

Do not use the camcorder in places where wireless use is prohibited such as on a

•

plane.

For the latest information on the Eye-Fi card, refer to the website of Eye-Fi, Inc.

•

(http://www.eye.fi/).

To transfer selected videos/still images



Preparation: Video/ Still image playback

Touch .

Eye-Fi Setting [OFF]

Eye-Fi Setting [ON]

Ready for Transfer from the Eye-Fi card

Transferring from the Eye-Fi card (animated)

Touch the video/still image to transfer.

A check mark( ) appears on the selected video/still image. If you touch the video/still image with a check mark, the selection is cancelled. Touch [SEL ALL] to select all the video/still image files. Touch [REL ALL] to cancel all the selection.

( ) appears on the transferred files.

Touch [SET].

Touch [SAVE] when the confirmation message appears.

Further Information

Troubleshooting

Before requesting service, consult the following chart. If the solutions indicated in the chart do not solve the problem, consult your nearest JVC dealer or JVC service center for instructions. Refer also to the FAQ section on JVC’s website (http://www.jvc.com).

 The following phenomena are not malfunctions.

LCD monitor momentarily becomes red or black when sunlight is recorded.

•

Black spots, or red, green, or blue spots appear on the LCD monitor.

•

(The LCD monitor contains 99.99% effective pixels, but 0.01% or fewer pixels may be

ineffective.) The camera is a microcomputer-controlled device. Electrostatic discharge, external noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such a case, reset the camcorder by pressing and holding the Power

button for more than 10 seconds. If you reset the camcorder, reset the clock. (P.18)

Troubles

Trouble Action Page

Unable to turn on the power.

Unable to charge the

Battery

battery.

The battery depletes even when connected to AC adapter.

Charging takes a long time.

Recharge the battery.

•

When the battery level is extremely low, the

•

camcorder does not turn on until it is charged even if it is connected to the computer or AC adapter.

Check the remaining battery power. (When the

•

battery is fully charged, the lamp does not flash.)

If you were charging the battery in a low or high

•

temperature environment, charge in an environment within the allowable operating temperature. (Charging may stop in an environment out of the allowable operating temperature for the protection of the battery.)

When charging using the computer, turn on the

•

computer.

Please use a JVC AC adapter (optional: AC-V10LU).

•

(Depending on the AC adapter you use, battery will deplete due to insufficient power supply from the adapter.)

Please use a JVC AC adapter (optional: AC-V10LU). 15

•

14 15

14, 15

–

Further Information

Trouble Action Page

Recording video/still image/audio cannot be performed.

During recording

Recording stops automatically.

The continuous shooting speed of still images is slow.

Sound or video is interrupted.

The same image is

During playback

displayed for a long time during video playback, or motion is choppy.

Image is stretched up and down on the TV.

When connecting to the HDMI mini cable, the image does not appear on the TV properly.

Computer

Unable to copy files to the computer's HDD.

The computer cannot recognize the SDXC card.

Check the video/still image/audio recording mode.

•

Select recording mode.

•

Turn off the power, wait for a while, and start

•

recording again. (This unit stops automatically to protect the circuit when the temperature rises.)

Recording stops automatically as it cannot be

•

performed for 12 or more consecutive hours according to specifications.

The continuous shooting speed will drop if this

•

function is used repeatedly.

Continuous shooting speed may drop depending

•

on the SD card or under certain recording conditions.

Sometimes playback is interrupted at the

•

connecting section between two scenes. This is not a malfunction.

Replace the SD card with a new one.

•

Perform [FORMAT SD CARD] in Basic Settings. (All data will be deleted.)

On the TV with aspect ratio of 4:3, images are

•

projected vertically.

Disconnect the HDMI mini cable and connect it

•

again.

Turn off and on this unit again. (The image or sound

•

may not appear on the TV properly depending on the TV connected.)

Connect the USB cable correctly.

•

Before copying files, make sure that enough free

•

space is left in the computer's hard disk (HDD).

Confirm and upgrade the OS of your computer. 13

•

20, 33

–

Further Information

Trouble Action Page

The LCD monitor is difficult to see.

A band of bright light

Specifications

Camera



Power consumption

2.2 W

Dimensions (W × H × D)

GC-WP10: 60 mm × 101 mm × 25 mm (2-3/8" × 4" ×1") GC-FM2 : 53 mm × 102 mm × 22 mm (2-1/8" × 4-1/16" × 7/8")

Weight

GC-WP10: 147 g (0.33 lbs) 152 g (0.34 lbs) (Including hand

strap and SD card) GC-FM2: 113 g (0.25 lbs) 115 g (0.26 lbs) (Including SD card)

Operating environment

Operating temperature: 0 °C to 40 °C (32 °F to 104 °F) Storage temperature: –20 °C to 50 °C (–4 °F to 122 °F) Operating humidity: 35 % to 80 %

Image pickup device

1/3.2" 5,130,000 pixels (progressive CMOS)

Recording area (Video)

(HD 1080) 2,090,000 pixels (HD 720) 3,400,000 pixels (QHD, iFrame) 2,090,000 pixels

Recording area (Still Image)

(Portrait) 5,030,000 pixels (Landscape) 2,760,000 pixels

Lens

F2.8, f=3.9 mm 35 mm conversion: (HD 1080) f=43.6 mm (HD 720) f=34.2 mm (QHD, iFrame) f=43.6 mm (Still image: Portrait) f=29.8 mm (Still image: Landscape) f=40.3 mm

LCD monitor

3.0" diagonally measured, LCD panel/TFT active matrix system

Zoom

Digital zoom: Up to 4x

Video recording format

Video: Mpeg-4 AVC/H.264 Audio: AAC 48 kHz 16 bit

256 kbps (2ch) GC-WP10: stereo sound GC-FM2: monaural sound

Still image recording format

JPEG standard Continuous shooting speed: approx. 1.5 shots/second

Audio recording format (GC-WP10 only)

Mpeg-1 Audio Layer 3 standard

Playable software:

Windows: LoiLoScope EX (supplied) Mac: QuickTime

Recording media

SD/SDHC/SDXC card (commercially available) Eye-Fi card (commercially available)

Connectors

HDMI

HDMI® mini connector

AV output

Video output: 1.0 V (p-p), 75 Ω Audio output: GC-WP10: 300 mV (rms), 220 Ω GC-FM2 : 300 mV (rms), 1 kΩ Headphones output (GC-WP10 only.

Also serves as AV output.)

USB

GC-WP10: Mini USB Type B, USB 2.0 compliant GC-FM2 : USB Type A, USB 2.0 compliant

Waterproof (GC-WP10 only)

Condition

Depth 3 m (10 ft)/30 minutes

Operation

Power on/off Video recording/stop Still image shooting

The specifications and appearance of this

•

product are subject to changes for further improvement without prior notice.

Further Information

Approximate Time/Number of Recording

Approximate Video Recording Time



SDHC

Type Quality

4 GB 16 GB 64 GB

1920 × 1080

HD 1080

HD 720

iFrame

QHD

The above recording time is approximate. The actual recording time may shorten

•

depending on the shooting environment.

Approximate Number of Still Images (Unit: Number of Shots)



Recording mode

(Image size)

Portrait (2592 × 1944)

Landscape (1440 × 1920)

30 frames/second

(Average 12 Mbps VBR)

1280 × 720

60 frames/second

(Average 12 Mbps VBR)

960 × 540

30 frames/second

(Average 24 Mbps VBR)

960 × 540

30 frames/second

(Average 5 Mbps VBR)

Card

1 GB 2 GB 4 GB 8 GB 32 GB 64 GB

300 600 1300 2700 9999 9999

600 1200 2300 4700 9999 9999

40 m 2 h 50 m 11 h 40 m

20 m 1 h 20 m 5 h 50 m

1 h 40 m 6 h 40 m 27 h 30 m

Card

SDHC

Card

SDXC

Card

SDXC

Card

The above number of shots is approximate. The number of recordable still images

•

may be less depending on the scene to record.

Further Information

Approximate Audio Recording Time (GC-WP10 only)



SDHC

Sound quality

4 GB 16 GB 64 GB

MP3 44.1 kHz 16 bit Stereo (128 kbps CBR)

The above recording time is approximate.

•

Approximate Recording Time (Using Battery)



Battery

Built-in Battery

The actual recording time may be shorter if zooming is used or if recording is stopped

•

repeatedly.

When the battery life is reached, the recording time becomes shorter even if the

•

battery is fully charged.

Approximate

Charging Time

When using the

computer:

3 h 00 m

When using the

AC adapter:

2 h 00 m

66 h 40 m 135 h 40 m 1093 h

Card

Actual Recording

Time

40 m 1 h 20 m

SDXC

Card

Continuous

Recording Time

Further Information

Customer Support Information

Use of this software is authorized according to the terms of the software license.

JVC

When contacting the nearest JVC office or agency in your country (refer to the JVC Worldwide Service Network at http://www.jvc-victor.co.jp/english/worldmap/index.html) about this software, please have the following information ready.

Product Name, Model, Problem, Error Message

•

PC (Manufacturer, Model (Desktop/Laptop), CPU, OS, Memory (MB/GB), Available Hard

•

Disk Space (GB))

Please note that it may take some time to respond to your questions, depending on their subject matter. JVC cannot answer questions regarding basic operation of your PC, or questions regarding specifications or performance of the OS, other applications or drivers.

LoiLo inc

Homepage: http://loilo.tv/product/15

Index

A-B repeat . . . . . . . . . . . . . . . . . . . . . . .29, 35

Audio mode . . . . . . . . . . . . . . . . . . . . . . . . 33

Basic settings . . . . . . . . . . . . . . . . . . . . . . . 45

Battery indicator ....................15

Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Clock adjust . . . . . . . . . . . . . . . . . . . . . . . . 18

Clock setting ........................18

Computer . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31, 38

Delete ...........................30, 37

Eect ...............................45

External audio le ...................36

Eye-Fi card ..........................42

Face priority AE . . . . . . . . . . . . . . . . . . . . . 23

Folder number ......................36

Index screen/thumbnail display . . . . . 10

Menu settings . . . . . . . . . . . . . . . . . . . . . . 45

Operation mode . . . . . . . . . . . . . . . . .28, 34

Recording in water ..................25

Recording mode ....................20

Recording time/number of recordable

still images . . . . . . . . . . . . . . . . . . . . . . . . . 50

SCREEN LOCK button . . . . . . . . . . . . . . . . 26

SD card .............................12

Self timer . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Size of still image . . . . . . . . . . . . . . . . . . . 22

Still image mode .................... 20

Time-lapse recording . . . . . . . . . . . . . . . 24

Touch AE . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Trimming ...........................31

Video image quality .................21

Video mode . . . . . . . . . . . . . . . . . . . . . . . . 20

Viewing on TV . . . . . . . . . . . . . . . . . . . . . . 32

0810YMH-AL-OT

JVC 0810YMH-AL-OT, GC-WP10, GCWP10AUS, GCFM2AUS User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Safety Precautions

Cautions

Daily Maintenance

Table of Contents

Names and Functions of Components

Indications on LCD Monitor

Getting Started

Accessories

Attaching the Core Filter to the USB Cable

Inserting an SD Card

Charging the Battery

Using the Touchscreen

CLOCK SETTING

Recording

Recording Video/Still Images

Useful Functions for Recording

Playback

Playing Back on the Camcorder

Deleting Files

Viewing Files on TV

Audio Recording

Audio Playback

Connecting with a Computer

Make a Backup on Computer

Using the Supplied Software

Using an Eye-Fi Card

Menu

Using the Menu

Further Information

Troubleshooting

Specifications

Approximate Time/Number of Recording

Customer Support Information

Index