Jura Impressa S, Impressa S Avantgarde Quick Reference Manual

Impressa S Avantgarde Quick Reference Guide

This Guide does not replace the Operating Instructions.

For details and cautions you must read all instructions.

Traces of Coffee Grounds in New Machine?

This is normal! Grinder was tested during assembly with beans.

Despite cleaning, traces of ground coffee may be found.

RED TEXT represents display text.

A) First Time Ever Preparation

1. Fill water in tank and beans in bean container.

2. DO NOT install the Clearyl Filter Cartridge now!

3. Push the main power switch in the back of the machine.

4. Push the ON/OFF button in the display. When the display
reads

FILL SYSTEM / PRESS STEAM place a cup under

the frot he r and push the PERMANENT STEAM button.

SYSTEM FILLING then HEATING UP.

5.

PRESS RINSE. Place a cup under the coffee spouts and

press the RINSE button. MACHINE RINSING. SELECT

PRODUCT.

6. Place a large cup underneath the coffee spouts and press
the

1-CUP coffee button. 1 COFFEE: The machine
starts grinding and brewing. Repeat once. Discard the first
two cups of coffee.

B) Daily Preparation

1. Fill fresh water in tank and check bean container.

2. Push ON/OFF button. HEATING UP. PRESS RINSE. Place
a cup under the coffee spouts and press the RINSE button.

MACHINE RINSING. SELECT PRODUCT.

Important: You can only brew coffee when display shows

SELECT PRODUCT

C) Grinding and Brewing Coffee

Four pre-set coffee buttons: 1 ESPRESSO, 2 ESPRESSI,

1 COFFEE, 2 COFFEES. These buttons ar

e pre-set for
strength (five settings), cup size (1 to 8 oz. per cup) and
temperatur

e (HIGH, NORMAL) During br

ewing you can over

-

ride the cup size by tur

ning the

ROT

AR

Y DIAL

. Cup size for
2-cup buttons is shown PER CUP! In programming you can
change all three functions.
Important: You can always stop the flow of coffee by push­ing any of the cof

fee buttons.

Selector Switch

1. Push and hold the RINSE button EMPTY TRAY/

EMPTY GROUNDS.

2. Remove and empty the tray and the used coffee
container and replace.

Attention: You must remove the

tray for 20 secondseven if it is empty. Replace tray.

AGENT IN TANK/PRESS STEAM

3. Empty the Water Container. Remove the Dual Frother.

4. Dissolve 3 of the large square decalcifying tablets in a
container with 20 oz. of water (0.6 liters) and pour the
solution into the water tank. Replace water tank.

5. Place a large container under the steam nozzle and
push either steam button. MACHINE DE-SCALING.
The machine pumps the mixture through the
steam nozzle. After 10 minutes

OPEN TAP.

7. Empty the container underneath the steam nozzle and
place it underneath the hot water spout.

8. Turn the Selector switch to the hot water position.

MACHINE DE-SCALING. After approximately six

minutes the display shows CLOSE TAP.

9. Turn the selector switch back to the cup symbol

MACHINE DE-SCALING. The machine will now pump

the mixture into the water tray inside. After another 12
minutes the display shows

EMPTY TRAY/EMPTY

GROUNDS

.

10. Carefully remove the used water tray,

TRAY MISSING,

empty it, clean and replace. Display s h o w s FILL

WATERTANK/RINSE WATERTANK.

11. Remove the water tank, rinse, fill halfway with water
and replace. The display shows

PRESS STEAM.

12. Place a large container under the steam nozzle and
push either steam button.

MACHINE DE-SCALING.

After 2 minutes

OPEN TAP.

13. Empty the container underneath the steam nozzle and
place it underneath the hot water spout.

14. Turn the Selector switch to the hot water position.

MACHINE DE-SCALING

15. After a short while the display shows CLOSE TAP.

16. Turn the selector switch back to the cup symbol. The
machine will pump fresh water into the used water
tray inside.

MACHINE DE-SCALING. After a short

while the display shows EMPTY TRAY/EMPTY

GROUNDS.

17. Carefully remove the used water tray,

TRAY MISSING,

empty and replace. PRESS RINSE.

18. Place a container under the coffee spout and press
the RINSE button. MACHINE RINSING.

SELECT PRODUCT

M) Supplies

can be or

der

ed thr

ough:

Customer Service, Mail Order Form or www.capresso.com

• Clearyl Water Filter Cartridge: #64553

• Cleaning T

ablets: #62205

• Decalcifying T

ablets: #61848

N) Using the

frothXpress
PLUS System

This system siphons
milk and automatically
produces preprogram­med amounts of hot
frothed or hot steamed
milk right into your cups,
never wasting any milk!

1. Disconnect the Dual­Frother PLUS from
the steam nozzle.

2. Fill the milk container
with milk and
assemble milk con­tainer (see above).
Attach the frothXpress to the steam nozzle. Attach the milk
container to the fr

othXpress (see above).
Important: Make sure all parts are connected tightly,
otherwise siphoning does not work.

3. Set the dial to the (–) minus sign (12 o’clock) of the frothing
range for cappuccino or to the (–) minus sign (6 o’clock)
of the steaming range for latte.

4. Place cup underneath the frother.

5. Make sure the red lights in the STEAM button are ON.

6. Push the

STEAM PORTION button.The steam will create
hot frothed milk right in your cup and will stop after 14 sec.
Change the steaming time in programming or use the
PERMANENT STEAM button for more or less milk.

7. For hotter milk in either position move the dial more
towards the (+) plus symbols.

(The extra long hose lets you siphon milk from any carton
without using the special milk container.)

Tip: Use chocolate milk to make great Hot Chocolate!

O) Cleaning the frothXpress PLUS System

Should be done right after use, takes less than 30 seconds.

1. Store the milk container in the refrigerator and remove the
frothXpress from the steam nozzle.

2. Drop the hose and the frothXpress in a cup of hot water.
This will push out any milk residue and prevents milk from
hardening inside the system.

3. Place a cup underneath the steam nozzle and push the
STEAM button for three seconds.

4. Replace frothXpress system.

CAPRESSO CUSTOMER SERVICE: 1-800-220-5701

M-F 9AM - 9PM; Sat. 9AM - 5PM EST
F

AX: 201-767-9684 contact@capr

esso.com

1

2

3

frothXpress
Plus
attached

Milk

C

ontainer

Assembly

F

rothing

range

Steaming
range

Steam only
no siphoning

DIAL

+
+

_

_

S

ELECT

P

RODUCT

Steam

Portion

Permanent

Steam

ON/OFF

Rinse

SELECT

PRODUCT

Four Coffee Buttons

A

LA Carte

Rotary Dial

with

Push-Button

A LA CARTE button. Push the button and change the
strength by turning the

ROTARY DIAL (XMILD, MILD,

NORMAL, STRONG, XSTRONG). Now push the ROTARY

DIAL

. During grinding turn the Dial to set the cup size.

D) Changing the Grinder Fineness
Important:

You can only adjust the fineness during the

actual grinding process.

1. Open the bean container lid and turn the dial while grinding:
larger dots: coarser; smaller dots: finer.

2. For darker, oily beans, grind somewhat coarser. For lighter
beans, grind somewhat finer.

E) Using Hot Water (factory setting is 5 oz.)
Place a cup underneath the Hot Water Spout and turn the
SELECTOR SWITCH to the right. WATER PORTION. To stop
the hot water flow turn the

SELECTOR SWITCH to the left.

F) Frothing and Steaming with the DUAL FROTHER PLUS

(Using the frothXpress PLUS system see section "N").
Important: All frother parts must be tightly connected and clean.

1. Cappuccino: One shot espresso plus ~4 oz. of steamed
and frothed milk. Metal frother sleeve DOWN.

2. Latte: One shot espresso plus ~4 to 5 oz. of steamed milk.
Metal frother sleeve UP

.

3. If the red lights in the steam buttons are ON, immerse
the frother into a pitcher with milk and push the
PERMANENT STEAM button. DRAW OFF STEAM. Steam
pushes into the milk ( if the steam buttons are not illumi­nated, see chapters 16.6 Operating Instructions).

a) Push the

STEAM button to stop. SELECT PRODUCT.

To continue steaming push the STEAM button again.

b) After steaming you can immediately brew coffee.

Important: Knocking Noise during Frothing: The machine
pumps water droplets for steam. This is normal.
Please note: Skim and 1% milk will produce more froth
than 2% and regular milk.

To increase milk temperature, frother sleeve should be UP.

G) Cleaning the Frother

Should be done right after use, takes less than 15 sec.!
Place a large cup underneath the frother. Push the PERMANENT

STEAM

button. After 5 sec. push the button again to stop.

H) Pr

ogramming

Factory Settings:

• 1-cup Espr

esso: 2 oz., str

ong

• 2-cup Espresso: 2 oz./cup, strong

• 1-cup Coffee: 5 oz., strong

• 2-cup Coffee: 5 oz./cup, strong

• All cup buttons ar

e set to temperatur

e HIGH.

• Hot Water: 5 oz.

• Steam Portion: 14 seconds

All other settings see chapter 5, Operating Instructions.

• Push the

RINSE button. INSERT FILTER / PRESS

STEAM

.

• Remove water tank, remove old filter. Keep the
extension rod. Rinse new filter under running water,
attach to extension and install in water tank. Fill with
fresh water and insert water tank into machine.

• Place a 20 oz. container under the Steam Nozzle and
push either steam button. The display shows

FILTER

RINSING

. Initially, the water may have a slight discol­oration. After 60 seconds the water flow stops. The
filter is activated. The display shows

SELECT

PRODUCT.

K) Cleaning with Special Tablet (Machine is on)

The message CLEAN MACHINE appears after 220
cups of coffee. This cleaning program removes coffee
oils inside the machine and takes less than 15 minutes.

Important: Do not interrupt program once started.
Important: Only use special round cleaning tablet.

SELECT PRODUCT/CLEAN MACHINE

1. Fill Water Tank and push and hold the RINSE
button until EMPTY TRAY/EMPTY GROUNDS.

2. Remove and empty the tray and the used coffee
container and replace.
Attention: You must remove the tray for 20 seconds
even if it is empty. Replace tray. PRESS RINSE

3. Place a large container (24 oz.) underneath the
coffee spout and push the RINSE button.

MACHINE CLEANING.

Then

ADD TABLET/PRESS RINSE

4. Drop one white tablet into the ground coffee funnel.

5. Push the

RINSE button. MACHINE CLEANING.

After a few minutes EMPTY TRAY/EMPTY

GROUNDS

.

6. Carefully lift, remove and empty tray and replace.
The display shows SELECT PRODUCT.

7. Remove the funnel and rinse under hot water.

L) Decalcifying DE-SCALE MACHINE

For different water hardness levels see Operating
Instructions (chapter 15). If a water hardness level is
selected, the decalcifying monitor is active. The
machine needs to be decalcified when above
message appears.

Important: If you use the Clearyl filter and DE-SCALE

MACHINE appears, then the Clearyl Activation proce-

dure was not performed properly (see "I" above).
Important: Decalcifying program must not be interrupted.
Use only the special decalcifying tablets (not the
cleaning tablets!). For supplies see other side.

• Open Front Cover and push and hold the

ROTARY DIAL

FILTER NO

.

• Slowly tur n the Dial clockwise to scroll through the
following functions after

FILTER NO: HARDNESS, RINSE,

POWDER QUANTITY (strength), WATER QUANTITY (cup

size), TEMP, WATER PORTION, STEAM PORTION,

ECONOMY, TIME, UNIT ON, OFF AFTER, LANGUAGE,
DISPLAY, INFO, EXIT.

• To exit programming choose EXIT and push the ROTARY
DIAL

: SELECT PRODUCT.

Programming Coffee Strength / POWDER QUANTITY

Here is how to change the coffee strength for the 1-cup
coffee button:

•

SELECT PRODUCT, push and hold the ROTARY DIAL,
FILTER NO.

• Turn the Dial until display shows POWDER QUANTITY.

• Push the Dial to get into the function.

SELECT PRODUCT.

• Push the 1-cup coffee button: STRONG.

• Turn the Dial to select (example) MILD.

• Push the Dial to confirm and tur n the Dial to EXIT.

• Push the Dial:

SELECT PRODUCT. From now on the

1-cup coffee button will brew MILD coffee.

I) Installing the Clearyl Cartridge
Important: Never install the cartridge before or during

"First Time Ever Preparation”.

• Rinse cartridge under running water. Snap the extension

tube on top of the cartridge. Insert into Water Tank recep­tion and make sure the tapered end fits snugly inside the
fins. Close cartridge holder.

• Fill the tank with cold water.

Activating the Clearyl Cartridge:

You must activate the cartridge otherwise the machine can­not monitor it properly.

SELECT PRODUCT

1.Push the Rotary Dial until you hear a beep. The display

shows FILTER NO

2.Push the Rotary Dial again, to enter the FILTER function.

3.Turn the Rotary Dial until the display shows

FILTER YES

and push the Rotar y D ia l to confirm. The display shows

INSERT FILTER/P R ES S STEAM.

4.Place a 20 oz. container under the Steam Nozzle and push

either steam button. The dis p l ay s h o ws

FILTER RINSING.

Initially, the water may have a slight discoloration. After 60
seconds the water flow stops. The filter is activated. The

display shows SELECT PRODUCT.
Please note: As long as the filter is activated, the water
hardness setting is automatically turned off.

J. Replacing the Clear

yl Car

tridge

When display shows SELECT PRODUC

T

/

CHANGE FILTER

and the RINSE button lights up: