1 Control elements ����������������������������������������������������������������������������������������������������4
2 For your safety
Comply with the instructions for use
Proper use
User limitations
Use by children
What to do in the event of damage
Preventing damage
Danger of electric shock
Danger of burns, scalding and injury
3 Preparing and using for the first time
Setting up the machine
Filling the bean container
Determining the water hardness
First-time use
u Water Tank symbol
ü Drip tray symbol
4 WiFi symbol
s Coffee Strength symbol
£ Ground Coffee symbol
5
2 For your safety
2 For your safety
Comply with the
instructions for use
Proper use
Before using the machine, read these instructions
for use thoroughly and completely and comply
with the instructions they contain� Keep these
instructions for use close to the machine and pass
them on to the next user�
Failure to observe the instructions for use may
result in serious injuries or damage to property�
Safety information is therefore indicated as follows:
J
WARNING
Indicates circumstances that may
result in serious injuries or death�
J
CAUTION
Indicates circumstances that may
result in minor injuries�
CAUTIONIndicates circumstances that may
result in damage to property�
The machine is intended for private domestic use�
It is intended only for coffee and hot water preparation� Use for any other purpose will be deemed
improper�
User limitations
6
People, including children, who
do not have the physical, sensory or mental
U
capabilities to use the machine safely or
are inexperienced or lack knowledge
U
must be supervised by a responsible person when
using it, or must be instructed in how to use it
correctly�
2 For your safety
When using the CLARIS Smart filter cartridge or
a JURA WiFi Connect, wireless connections are
established� Specific details on the frequency band
used and the maximum transmission power can be
found in the ‘Technical data’ section�
Use by children
What to do in the
event of damage
Children must be able to recognise and
understand the potential dangers arising
from incorrect use:
Keep children under the age of 8 away from
U
the machine, or supervise them constantly�
Children aged 8 and over may only operate
U
the machine without supervision if they have
been instructed in how to use it safely�
Children may not clean or service the machine
U
unless supervised by a responsible person�
Do not allow children to play with the machine�
U
Never use a damaged machine or mains cable.
This could result in fatal electric shock.
In the event of signs of damage, disconnect the
U
machine from the mains� To do this, first switch
the E4 off with the On/Off button Q� Only then
should you remove the mains plug from the
power socket�
Replace a damaged plug-in mains cable with
U
an original JURA mains cable� Unsuitable mains
cables may result in consequential damage�
Only permit authorised JURA service centres to
U
carry out repairs to the machine and the
permanently connected mains cable. Unsuitable repairs may result in consequential damage�
7
2 For your safety
Preventing damage
To avoid damage to the machine and the mains
cable:
Do not use the E4 and the mains cable near
U
hot surfaces�
Do not allow the mains cable to rub against
U
sharp edges and ensure that it does not
become trapped�
Never allow the mains cable to loosely hang
U
down� The mains cable could pose a tripping
hazard or become damaged�
Protect the E4 from weather and direct sunlight�
U
Only connect the E4 to a mains voltage corre-
U
sponding to that stated on the rating plate� The
rating plate is located on the underside�
Connect the E4 directly to a domestic power
U
socket� Using multi-socket adapters or extension cords may cause overheating�
Do not use alkaline or alcohol-based cleaning
U
agents; only use mild cleaning agents and a
soft cloth�
Do not use any coffee beans treated with
U
additives or caramelised coffee beans�
Only fill the water tank with fresh, cold,
U
non-carbonated water�
Switch the machine off with the On/Off
U
button Q if you are going to be absent for a
longer period of time and remove the mains
plug from the power socket�
Only use original JURA maintenance products�
U
Use of products that are not explicitly recommended by JURA could damage your E4�
8
2 For your safety
Danger of electric
shock
Danger of burns,
scalding and injury
Water conducts electricity. Do not bring water
and electricity into contact with one another:
Never touch the mains plug with wet hands�
U
Do not immerse the E4 and/or mains cable in
U
water�
Do not put the E4 or any individual parts in the
U
dishwasher�
Before cleaning, switch the E4 off with the
U
On/Off button Q� Always wipe the E4 with a
damp cloth rather than a wet one, and protect
it from prolonged exposure to water splash�
The E4 must not be cleaned with a jet of water�
The E4 is not suitable for installation on a
U
surface where a jet of water can be used�
Do not touch the spouts during operation� Use
U
the handles provided�
Optionally, your E4 can be remotely operated
U
using mobile devices� When preparing a
product or initiating a maintenance
programme, make sure that other people are
not put at risk – for example, through contact
with the spouts�
9
3 Preparing and using for the first time
3 Preparing and using for the first time
Setting up the machine
Filling the bean container
CAUTION
When setting up your E4, please note the following:
Place the E4 on a horizontal surface that is not sensitive to
U
wa ter�
Choose a spot for your E4 which protects the machine against
U
overheating� Ensure that the ventilation slots are not covered�
The bean container has an aroma preservation cover� This will ensure
that your coffee beans retain their aroma for longer�
Coffee beans which have been treated with additives (e�g� sugar),
ground coffee or freeze-dried coffee will damage the grinder�
T
Only use roasted, untreated coffee beans to fill the bean
container�
T
Remove the aroma preservation cover�
T
Remove any dirt or foreign objects from inside the bean
container�
T
Fill the bean container with coffee beans and close the aroma
preservation cover�
Determining the water
hardness
10
When you use the machine for the first time, you must set the water
hardness� If you do not know the hardness of your water, you can
find this out first� Use the Aquadur® test strips supplied with the
machine�
T
Hold the test strip under flowing water for one second� Shake
off the water�
T
Wait for about 1minute�
T
You will then be able to read the degree of water hardness
from the discolouration of the Aquadur® test strip and the
description on the packaging�
First-time use
3 Preparing and using for the first time
J
WARNING
CAUTION
If the machine is operated with a defective mains cable, there is a
danger of potentially fatal electric shock�
T
Never use a machine which is damaged or has a defective mains
cable�
Milk, sparkling mineral water or other liquids can damage the
water tank or the machine�
T
Only fill the water tank with fresh, cold water�
Precondition:The bean container has been filled�
T
For machines with a plug-in mains cable: Connect the mains
cable to the machine�
T
Insert the mains plug into a power socket�
T
Press the On/Off button Q�
E The number of symbols that are brightly lit up indicates the
water hardness level: 1–7°dH(
16–23°dH(
sss) and 24–30°dH (sss £)�
s), 8–15°dH(ss),
E If you do not know the hardness of your water, you can find
this out first (see chapter 3 ‘Preparing and using for the first
time – Determining the water hardness’)�
T
Press the i/o button to set the water hardness�
T
Press the s button to confirm the setting�
The
! and u symbols appear�
T
Remove the water tank and rinse it with cold water�
T
Fit the filter cartridge extension supplied on top of the CLARIS
Smart filter cartridge�
T
Insert the filter cartridge with its extension into the water tank�
T
Turn the filter cartridge clockwise until it audibly clicks into
place�
T
Fill the water tank with fresh, cold water and reinsert the tank�
E The machine automatically detects that you have just
inserted the filter cartridge� The
sss £ symbols flash
from right to left to show that you need to open the switch
for hot water preparation�
11
3 Preparing and using for the first time
Connecting the machine to
the WiFi network
(optionally)
T
Place a receptacle under the hot-water spout�
T
Turn the switch to thex position�
The filter is rinsed� Water flows out of the hot-water spout�
Rinsing of the filter stops automatically� The
sss £ symbols
flash from left to right�
T
Turn the switch to the °position�
The
ü symbol lights up�
T
Empty the drip tray and put it back into the machine�
T
Place a receptacle under the coffee spout�
The
sss £ symbols flash while the E4 is heating up�
The machine is rinsed� Water flows out of the coffee spout�
The rinse stops automatically� Your E4 is ready for use�
®
Your E4 can be connected with your JURA app (J�O�E�
Precondition: J�O�E�
®
is installed on your mobile end device� The
)�
optionally available JURA WiFi Connect is inserted into the service
socket of your E4�
12
For more information on setting up the WiFi Connect go to
jura.com/wifi or scan the QR code�
4 Preparation
Basic information about preparing drinks:
AimWhat to do
Select coffee
strength
Press the s button before preparation:
‘mild’ (s), ‘normal’ (ss) or ‘strong’ (sss)�
The E4 remembers the last option selected for
the next preparation�
Cancel
Press any button
preparation
4 Preparation
Espresso and coffee
Two espressi and two
coffees
E All products can also be prepared using the JURA app (J�O�E�E With the JURA app (J�O�E�
®
) you can make two additional
®
speciality coffees: the caffè Barista and the lungo Barista�
Coffee tastes best served hot� A cold porcelain cup cools the
beverage – and impairs the taste� We therefore recommend
prewarming the cups� You can purchase a JURA cup warmer from
your specialised dealer�
Example:Coffee
T
Place a cup under the coffee spout�
T
Press the o button�
The preset amount of water for coffee flows into the cup�
Example:Two espressi
T
Place a cup under the coffee spout�
T
Press the i button 2x.
E Two brewing operations take place one after the other�
Change the cup before the second brewing operation�
E To prepare two coffees, press the o button 2x.
)�
The preset amount of water for espresso flows into the cup�
13
4 Preparation
Hot water
T
Place a cup under the hot-water spout�
T
Turn the switch to thex position�
Hot water flows into the cup�
T
Turn the switch to position ° to stop the preparation of hot
wa ter�
Caffè Barista and lungo
Barista (optionally with
®
J.O.E.
)
Permanently setting the
amount of water for the cup
size
®
The JURA app (J�O�E�
) offers two additional products for you to
choose from: caffè Barista and lungo Barista�
Example:Lungo Barista
T
Place a cup under the hot-water spout�
T
In the JURA app (J�O�E�
T
Follow the instructions in the app�
®
), tap the product ‘Lungo Barista’�
It is easy to make permanent settings for the amount of water for all
speciality coffees according to the cup size� Adjust the amount once
as shown in the following example� Every time you prepare a drink
in the future, this amount of water will be dispensed�
Example:Proceed as follows to permanently set the amount of
water for one coffee�
T
Place a cup under the coffee spout�
T
Press the o button for about 2 seconds.
The coffee flows into the cup�
T
Press any button as soon as there is sufficient coffee in the cup�
Preparation stops� The set amount of water for one coffee is
permanently stored�
14
E You can alter this setting at any time by repeating the above
procedure�
4 Preparation
Adjusting the grinder
CAUTION
wq
Ground coffee
You can adjust the grinder to suit the degree of roast of your coffee�
If you adjust the consistency of grind when the grinder is not
operating, the grinder adjustment switch could be damaged�
T
Only adjust the consistency of grind when the grinder is
running�
E The consistency of grind is correct if the coffee flows
regularly from the coffee spout� In addition a fine, thick
crema forms�
Grinder adjustment switch
1: Fine consistency of grind setting
U
2: Coarse consistency of grind setting
U
Example:Proceed as follows to change the consistency of grind
during the preparation of an espresso�
T
Place a cup under the coffee spout�
T
Open the cover of the filler funnel for ground coffee�
T
Press the i button�
T
Turn the grinder adjustment switch to the desired position
while the grinder is running�
The preset amount of water flows into the cup�
T
Close the filler funnel cover�
You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee�
Basic information about ground coffee:
Never add more than two level measuring spoons of ground
U
coffee�
Use ground coffee which is not ground too finely� Very fine
U
coffee can block up the system so that the coffee only comes
out in drips�
If you did not fill the machine with enough ground coffee,
U
the
£ symbol flashes and the E4 stops the operation�
The desired speciality coffee must be prepared within approxi-
U
mately one minute after filling with the ground coffee�
Otherwise the E4 stops the operation and is once more ready
for use�
All speciality coffees with ground coffee are always prepared following the same model�
15
4 Preparation
5 Daily operation
Switching the machine on
and off
Example:Proceed as follows to prepare an espresso using ground
coffee�
T
Place an espresso cup under the coffee spout�
T
Press the s button several times until the
brightly�
T
Open the powder chute cover�
T
Place one level measuring spoon of ground coffee into the filler
funnel�
T
Close the cover of the filler funnel�
T
Press the i button�
The preset amount of water for espresso flows into the cup�
T
Place a receptacle under the coffee spout�
T
Press the On/Off button Q�
£ symbol lights up
Filling the water tank
CAUTION
16
E When the machine is switched off, the system is only rinsed
if a speciality coffee has been prepared�
The system rinses itself� Your E4 is switched on or off�
Daily maintenance of the machine and hygiene when handling coffee and water are key to a perfect coffee result in the cup every time�
You should therefore change the water daily�
Milk, sparkling mineral water or other liquids can damage the
water tank or the machine�
T
Only fill the water tank with fresh, cold water�
T
Open the water tank cover�
T
Remove the water tank and rinse it with cold water�
T
Fill the water tank with fresh, cold water and reinsert the tank�
T
Close the water tank cover�
5 Daily operation
Maintenance actions
Maintenance actionDaily If necessaryNote
Empty the drip tray and coffee grounds
container and rinse with warm water
(The drip tray and coffee grounds
container are dishwasher-safe, but the
insert for the drip tray is not)
Rinse the water tank
Wipe the surface of the machine with a
clean, soft, damp cloth (e�g� microfibre
cloth)
Clean the inside of the water tank with a
brush
Clean the top and bottom of the cup
grille
Optimal coffee quality depends on many factors� One important
prerequisite is regular maintenance of your E4� Carry out the following steps:
Z
Z
Z
Z
Z
Always empty the coffee
grounds container when the
machine is switched on� This
is the only way of resetting
the coffee grounds counter�
6 Permanent settings in programming mode
Automatic switch-off
In programming mode you can set the switch-off time and water
hardness� Press the f button to enter programming mode�
By instructing your E4 to automatically switch itself off, you can cut
down your energy consumption� Your E4 switches off automatically
after the preset time following the last action on the machine�
The number of symbols that are brightly lit up indicates the set
switch-off time:
Switch-off timeSymbol(s) shown in display
30minutes
1hour
2hours
4hours
T
Press the f button�
The
& symbol lights up brightly�
s
s s
s s s
s s s £
17
6 Permanent settings in programming mode
Setting the water hardness
T
Press the o button several times until the
ü symbol lights up
brightly�
T
Press the s button to enter the programme item�
T
Press the i/o button to change the setting for the switch-off
time�
T
Press the s button to confirm the setting�
E The setting must be confirmed within 20 seconds�
The
sss £ symbols flash 3 times in quick succession�
T
Press the f button to exit programming mode�
E The automatic switch-off can also be set using the JURA app
®
)�
(J�O�E�
The harder the water, the more frequently you need to descale the
E4 or change the filter� It is therefore important to set the water
hardness accurately�
The water hardness was set when the machine was first used� You
can change this setting at any time�
The number of symbols that are brightly lit up indicates the set
water hardness level:
Water hardnessSymbol(s) shown in display
1–7°dH
8–15°dH
16–23°dH
24–30°dH
s
s s
s s s
s s s £
18
T
Press the f button�
& symbol lights up brightly�
The
T
Press the o button several times until the
u symbol lights up
brightly�
T
Press the s button to enter the programme item�
T
Press the i/o button to change the setting for the water
hardness�
T
Press the s button to confirm the setting�
E The setting must be confirmed within 20 seconds�
sss £ symbols flash 3 times in quick succession�
The
T
Press the f button to exit programming mode�
7 Maintenance
7 Maintenance
Your E4 has the following integrated maintenance programmes:
Cleaning the machine (L)
U
Descaling the machine (&)
U
E If a maintenance programme needs to be started, the appro-
priate symbol lights up� If this happens, run the appropriate
maintenance programme�
Inserting/changing the filter
Once the filter cartridge stops working (depending on the water
hardness setting), the E4 will prompt you to change the filter�
E Your E4 no longer has to be descaled if you are using the
CLARIS Smart filter cartridge�
E CLARIS Smart filter cartridges are available from specialised
dealers�
Precondition:Your E4 is ready for use� The filter symbol
up (if you are already using a filter and the filter capacity is
depleted)�
T
Remove and empty the water tank�
T
Turn the filter cartridge anticlockwise and remove it along with
the extension from the water tank�
T
Fit the filter cartridge extension on top of a new CLARIS Smart
filter cartridge�
T
Insert the filter cartridge with its extension into the water tank�
T
Turn the filter cartridge clockwise until it audibly clicks into
place�
T
Fill the water tank with fresh, cold water and reinsert the tank�
The machine automatically detects that you have inserted/
changed the filter cartridge�
The
sss £ symbols flash from right to left to indicate that
you need to open the switch for hot water preparation�
T
Place a receptacle under the hot-water spout�
T
Turn the switch to thex position�
The filter is rinsed� Water flows out of the hot-water spout�
Rinsing of the filter stops automatically� The
flash from left to right�
T
Turn the switch to the °position�
The
ü symbol lights up�
T
Empty the drip tray and coffee grounds container and put them
back into the machine�
sss £ symbols
! lights
19
7 Maintenance
Cleaning the machine
CAUTION
max.
2X
After 180preparations or 80switch-on rinses, the E4 will prompt you
to clean it�
If the wrong cleaning agent is used, the machine could be
damaged and/or traces could be left behind in the water�
T
Use only original JURA maintenance products�
E The cleaning programme lasts approximately 20 minutes�E Do not interrupt the cleaning programme� The quality of
cleaning will be impaired if you do so�
E JURA cleaning tablets are available from specialised dealers�
Precondition:The
T
Press the f button for about 2 seconds.
The
ü symbol lights up�
T
Empty the drip tray and coffee grounds container and put them
L symbol lights up� The water tank is filled�
back into the machine�
T
Place a receptacle under the coffee spout�
T
Press the s button�
The
ss symbols light up, water flows out of the coffee spout�
The operation is interrupted, the
T
Open the cover of the filler funnel for ground coffee�
T
Insert a JURA cleaning tablet into the filler funnel�
T
Close the cover of the filler funnel�
T
Press the s button�
sss symbols light up, water flows out of the coffee
The
£ symbol lights up�
spout several times� The operation stops automatically�
ü symbol lights up�
The
T
Empty the drip tray and coffee grounds container and put them
back into the machine�
The
sss £ symbols flash 3 times in quick succession�
Descaling the machine
20
The E4 builds up deposits of limescale over time and automatically
prompts you to descale it when necessary� The degree of calcification depends on the hardness of your water�
E If you are using a CLARIS Smart filter cartridge, you will not
be prompted to descale� However, should you need to
descale the E4, first switch the machine to descaling mode
(see section 7 “Maintenance – Switching the machine from
filter mode to descaling mode”)�
J
CAUTION
7 Maintenance
If the descaling agent comes into contact with the skin or eyes,
this can cause irritation�
T
Avoid contact with the skin or eyes�
T
Rinse off the descaling agent with clean water� Should you get
any descaling agent in your eye, see a doctor�
CAUTION
CAUTION
CAUTION
If the wrong descaling agent is used, the machine could be
damaged and/or traces could be left behind in the water�
T
Use only original JURA maintenance products�
If the descaling operation is interrupted, there may be damage to
the machine�
T
Allow the descaling programme to run to the end�
If the descaling agent comes into contact with sensitive surfaces
(e�g� marble), damage cannot be ruled out�
T
Clean up any splashes immediately�
E The descaling programme lasts approximately 45minutes�E JURA descaling tablets are available from specialised dealers�
Precondition:The
T
Press the f button for about 2 seconds.
The
ü symbol lights up�
T
Empty the drip tray and coffee grounds container and put them
& symbol lights up�
back into the machine�
The
u symbol flashes�
T
Place a receptacle under the hot-water spout�
T
Remove and empty the water tank�
3x
T
Completely dissolve 3JURA descaling tablets in a receptacle
holding 500ml of water� This may take several minutes�
T
Pour the solution into the empty water tank and insert it into
the machine�
The
sss £ symbols flash from right to left to show that you
need to open the switch for hot water preparation�
21
7 Maintenance
T
Turn the switch to thex position�
Water flows repeatedly out of the hot-water spout� The process
stops automatically� The
sss £ symbols flash from left to
right�
T
Turn the switch to position °�
The descaling operation is continued�
The
ü symbol lights up�
T
Empty the drip tray and coffee grounds container and put them
back into the machine�
The
u symbol lights up�
T
Remove the water tank and rinse it thoroughly�
T
Fill the water tank with fresh, cold water and reinsert the tank�
sss £ symbols flash from right to left�
The
T
Place a receptacle under the hot-water spout�
T
Turn the switch to thex position�
Water flows repeatedly out of the hot-water spout� The process
stops automatically� The
sss £ symbols flash from left to
right�
T
Turn the switch to position °�
The descaling operation is continued�
ü symbol lights up�
The
T
Empty the drip tray and coffee grounds container and put them
back into the machine�
The
sss £ symbols flash 3 times in quick succession�
Cleaning the bean container
22
E If the descaling operation stops unexpectedly, rinse the
water tank thoroughly�
Coffee beans may be covered with a slight oil film which remains on
the walls of the bean container� These traces may negatively affect
the coffee result� For this reason clean the bean container from time
to time�
T
Press the On/Off button Q to switch the E4 off�
T
Remove the aroma preservation cover�
T
Clean the bean container with a soft, dry cloth�
T
Fill the bean container with coffee beans and close the aroma
preservation cover�
7 Maintenance
Descaling the water tank
Switching the machine from
filter mode to descaling
mode
Limescale deposits may form in the water tank� To ensure correct
function of the machine, descale the water tank from time to time�
T
Remove the water tank�
T
If you use a CLARIS Smart filter cartridge, remove this�
T
Completely fill the water tank and dissolve 3 JURA descaling
tablets in it�
T
Leave the water tank with the descaling solution for several
hours (e�g� overnight)�
T
Empty the water tank and rinse it thoroughly�
T
If you use a CLARIS Smart filter cartridge, insert this again�
T
Fill the water tank with fresh, cold water and reinsert the tank�
Follow the steps below to switch the E4 from filter mode to
descaling mode�
T
Remove the water tank�
T
Turn the filter cartridge anticlockwise and remove it along with
the extension from the water tank�
T
Fill the water tank and reinsert it�
T
Press the f button�
The
& symbol lights up brightly�
T
Press the o (‘Large cup’) button several times until the
! symbol
lights up brightly�
T
Press the s button to enter the programme item�
The
sss £ symbols light up brightly�
T
Press the i (‘Small cup’) button so that the
sss £ symbols
no longer light up brightly�
T
Press the s button to confirm the setting�
E The setting must be confirmed within 20 seconds�
The
sss £ symbols flash 3 times in quick succession� The
machine is now in descaling mode�
T
Press the f button to exit programming mode�
23
8 Display messages
8 Display messages
MessageCause/ResultAction
The u symbol lights
up�
ü symbol
The
lights up�
ü symbol
The
flashes�
The
L symbol lights
up�
& symbol lights
The
up�
! symbol lights
The
up�
sss £
The
symbols flash from
right to left�
The
sss £
symbols flash from
left to right�
! symbol lights
The
up even though no
filter has been
inserted�
sss symbols
The
flash after the beans
have been ground�
The water tank is empty� You cannot
prepare any products�
The coffee grounds container is full� /
The drip tray is full� You cannot
prepare any products�
The coffee grounds container is not
inserted correctly or is not inserted
at all� / The drip tray is not inserted
correctly or is not inserted at all� You
cannot prepare any products�
The E4 is prompting you to clean it�
The E4 is prompting you to descale
it�
The filter cartridge no longer works�
The switch for hot water preparation
must be opened�
The switch for hot water preparation
must be closed�
No CLARIS Smart filter cartridge was
inserted in the water tank after the
descaling programme finished�
The bean container is empty� You
cannot prepare any products�
T
Fill the water tank (see chapter 5
‘Daily operation – Filling the water
tank’)�
T
Empty the coffee grounds
container and the drip tray (see
chapter 5 ‘Daily operation –
Maintenance actions’)�
T
Fit the drip tray�
T
Perform cleaning (see chapter 7
‘Maintenance – Cleaning the
machine’)�
T
Perform descaling (see chapter 7
‘Maintenance – Descaling the
machine ’)�
T
Replace the CLARIS Smart filter
cartridge (see chapter 7 ‘Maintenance – Inserting/changing the
filter’)�
T
Turn the switch to
thex position�
T
Turn the switch to
the °position�
T
Insert a CLARIS Smart filter
cartridge in the water tank or set
the machine to descaling mode�
T
Fill the bean container (see
chapter 3 ‘Preparing and using for
the first time – Filling the bean
container’)
24
MessageCause/ResultAction
The £ symbol
flashes�
Not enough ground coffee was
added� The E4 cancels the operation�
T
Start preparation again�
9 Troubleshooting
ProblemCause/ResultAction
Coffee only comes out in
drips when it is being
prepared�
There is dry ground
coffee behind the coffee
grounds container�
Grinder is making a very
loud noise�
& symbol or the !
The
symbol lights up brightly
and other symbols flash�
The connection with the
WiFi Connect is not
working�
The coffee is ground too finely
and obstructs the system�
The water hardness may not
have been correctly set�
The beans used are resulting in
an above-average volume of
ground coffee�
There are foreign objects in the
grinder�
If the machine has been exposed
to the cold for a long period of
time, heating may be disabled
for safety reasons� The E4
switches off automatically�
The wrong PIN may have been
used�
T
Set the grinder to a coarser
setting (see chapter 4 ‘Preparation – Adjusting the grinder’)�
T
Perform descaling (see chapter 7
‘Maintenance – Descaling the
machine ’)�
T
Reduce the coffee strength or
choose a finer grinder setting�
T
Contact customer support in
your country (see chapter 13
‘JURA contact details/ Legal
information’)�
T
Warm the machine at room
temperature�
Reset the machine (including the
WiFi Connect) to factory settings
(the E4 must be "ready for use"):
T
Remove the drip tray�
The
T
Press and hold the f and
s buttons at the same time for
about 5 seconds�
The E4 switches off�
8 Display messages
ü symbol flashes�
E If you were unable to solve the problem, contact customer support in your country (see
10 Transport and environmentally friendly disposal
10 Transport and environmentally friendly disposal
Transport/ Emptying the
system
Disposal
Keep the packaging for your E4� It should be used to protect the
machine during transport�
In order to protect the E4 from frost during transport, the system
must be emptied�
Precondition:Your E4 is ready for use�
T
Place a receptacle under the hot-water spout�
T
Turn the switch to thex position�
T
Remove the water tank�
Water will continue to flow until the system is empty�
The
u symbol lights up�
T
Turn the switch to position °�
T
Switch the machine off with the On/Off button Q�
Please dispose of old machines in an environmentally neutral way�
H
Old machines contain valuable, recyclable materials which should
be recycled� Please therefore dispose of old machines via suitable
collection systems�
11 Technical data
Voltage220–240V~, 50Hz
Power1450W
Conformity mark
Pump pressurestatic, max� 15bar
Holding capacity of water tank (without filter)1�9l
Holding capacity of bean container280g
Holding capacity of coffee grounds containerapprox� 16 servings
Cable lengthapprox� 1�1m
Weightapprox� 9kg
Dimensions (W×H×D)28�0 × 35�1 × 44�6cm
CLARIS Smart filter cartridge (RFID technology)Frequency band 13�56 MHz
E You can find additional contact details for your country at
jura.com.
E If you need assistance with using your machine, you can find
this at jura.com/service.
E Your opinion is important to us! Use the contact details at
jura.com.
Directives
Technical changes
The machine complies with the following directives:
2014/35/EU– Low Voltage Directive
U
2014/30/EU– Electromagnetic Compatibility
U
2009/125/EC– Ecodesign Directive
U
2011/65/EU– RoHS Directive
U
2014/53/EU – Wireless Voltage Directive
U
A detailed EU Declaration of Conformity for your E4 can be found at
jura.com/conformity.
We reserve the right to make technical changes� The diagrams used
in these instructions for use are for illustration purposes only and do
not represent the original colours of the machine� Some details of
your E4 may vary�
32
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.