JURA C9 Operating Instructions

The IMPRESSA C9 Manual

The ‘IMPRESSA Manual’ has been awarded the seal of approval by the independent German T echnical Inspection Agency, TÜV SÜD, due to its easy-to-understand style, its thoroughness and coverage of safety aspects.

Table of contents

Your IMPRESSA C9

IMPORTANT SAFEGUARDS 4 Control elements Proper use For your safety The IMPRESSA C9 Manual

Symbol description ......................................................................................................................................12

1 IMPRESSA C9 13

Connector System© ....................................................................................................................................14

JURA on the Internet ....................................................................................................................................14

Knowledge Builder .......................................................................................................................................14

2 Preparing and using for the first time 15

Set up .............................................................................................................................................................15

Filling the water tank ...................................................................................................................................15

Filling the bean container ...........................................................................................................................15

First-time use ................................................................................................................................................16

Using and activating filter ..........................................................................................................................17

Determining water hardness and adjusting ............................................................................................18

Adjusting the grinder ..................................................................................................................................19

Switching on ................................................................................................................................................20

Switching off (standby) ..............................................................................................................................20

3 Familiarising yourself with the control options 22

Preparation at the touch of a button .......................................................................................................23

One-off settings before and during preparation ...................................................................................23

Adjusting the default amount of water to suit the cup size ................................................................24

Permanent settings in programming mode ..........................................................................................25

Query information and maintenance status..........................................................................................27

4 Preparation at the touch of a button 29

Espresso ........................................................................................................................................................29

Coffee ............................................................................................................................................................30

Cappuccino...................................................................................................................................................30

Pre-ground coffee .......................................................................................................................................32

Foaming milk with the Easy Cappuccino Frother .................................................................................33

Foaming and heating milk with the Professional Cappuccino Frother .............................................33

Hot water ......................................................................................................................................................34

Table of contents

5 Permanent settings in programming mode 35

Products ........................................................................................................................................................35

Energy-saving mode ..................................................................................................................................37

Time ..............................................................................................................................................................38

Programmable switch-on time .................................................................................................................38

Automatic switch-off ..................................................................................................................................39

Unit amount of water / Time format .......................................................................................................40

Language ......................................................................................................................................................40

6 Maintenance 42

Maintenance tips .........................................................................................................................................42

Rinse machine..............................................................................................................................................42

Filter change .................................................................................................................................................43

Clean machine .............................................................................................................................................44

Descale machine .........................................................................................................................................46

Rinsing the Easy Cappuccino Frother ......................................................................................................48

Cleaning the Easy Cappuccino Frother ...................................................................................................49

Disassembling and rinsing the Easy Cappuccino Frother....................................................................50

Rinsing the Professional Cappuccino Frother ........................................................................................50

Cleaning the Professional Cappuccino Frother .......................................................................................51

Disassembling and rinsing the Professional Cappuccino Frother ......................................................53

Cleaning the bean container .....................................................................................................................53

Descaling the water tank ...........................................................................................................................54

7 Display messages 55 8 Troubleshooting 9 Transport and environmentally neutral disposal

Transport / Empty system .........................................................................................................................58

Disposal .........................................................................................................................................................58

10 Technical data 59 Index

JURA contact details / Legal information

Important Safeguards

IMPORTANT SAFEGUARDS

These safeguards apply for machines with UL safety test (see rating plate and chapter 10, ‘Technical data’).

Follow the basic safety precautions

When using electrical appliances, basic safety precautions should always be followed, to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

Z Read all instructions. Z Do not touch hot surfaces. Use handles or knobs. Z To protect against fire , electric shock and injury to persons, do

not immerse cord, plugs, or body of machine in water or other liquid.

Z Close supervision is necessary when any appliance is used by

or near children.

Z Unplug from outlet when not in use and before cleaning.

Allow to cool before putting on or taking off parts, and before cleaning the appliance.

Z Do not operate any appliance with a damaged cord or plug or

after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.

Z The use of any accessory attachment not recommended by

the appliance manufacturer may result in fire, electric shock,

or injury to persons.

Z Do not use outdoors. Z Do not let the cord hang over the edge of a table or counter,

or touch hot surfaces.

Z Do not place on or near a hot gas or electric burner, or in a

heated oven.

Z Always attach plug to appliance first, then plug cord into the

wall outlet. To disconnect, turn any control to ‘OFF’ then

remove plug from wall outlet.

Z Do not use appliance for other than intented use. Z Use extreme caution when dispensing hot steam. Z For household use only.

SAVE THESE INSTRUCTIONS

Important Safeguards

Special cord set instructions

a. A short power supply cord is provided to reduce the risk

resulting from becoming entangled in or tripping over a long

cord. Your IMPRESSA has a 3-pin grounded plug. b. Longer extension cords are available and may be used if care

is exercised in their use. c. If an extension cord is used,

1. the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and

2. if the appliance is of the grounded type, the extension cord should be a grounding type 3-wire cord, and

3. the longer cord shall be arranged so that it will not drape over the counter top or tabletop where it can be pulled on by children of tripped over.

Z As a safety feature, this plug will fit in a polarized outlet only

one way.

Z If the plug does not fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified electrician.

Z Do not modify the plug in any way or attempt to defeat this

safety feature.

Warning

Caution

To reduc e the risk of fire or electric shock, do not remove any service covers. No user serviceable parts inside. Repair should be done by authorized personnel only.

This appliance is for household use. Any servicing other than cleaning and user maintenance should be performed by an authorized service representative:

Z Do not immerse base in water or try to disassemble. Z To reduce the risk of fire or electric shock, do not remove the

base. No user serviceable parts inside. Repair should be done by authorized service personnel only.

Z Check voltage to be sure that the voltage indicated on the

name plate complies with your voltage.

Z Never use warm or hot water to fill the water container! Use

cold water only.

Important Safeguards

Z Keep your hands and the cord away from hot parts of the

appliance during operation.

Z Never clean with scouring powders or hard implements.

NEVER DO (or you will void your warranty protection):

Z Never fill instant coffee, chocolat e mix et c. int o the grinder or

ground coffee funnel (grinder by-pass). It will damage the functioning of the brewing chamber.

Z Never fill sugar coated coffee beans into the bean hopper. In

case of doubt, call your dealer.

Z Never fill anything other than coffee beans into the bean con-

tainer (no chocolate, no rice, no nuts, no spices, nothing other than roasted coffee beans).

Z Never do anything with the machine which is not described in

the User‘s Manual. In case of doubt, call your dealer.

Important Safeguards

Control elements

2 3

Figure: IMPRESSA C9 Piano Black

1 Cover of filler funnel for pre-ground coffee 2 Filler funnel for pre-ground coffee 3 Water tank cover 4 Water tank 5 Power switch and power cable

(side of machine) 6 Coffee grounds container 7 Drip tray

8 Fineness of grind switch 9 Bean container cover 10 Bean container

with aroma preservation cover

11 Connector System

for removable frothers 12 Easy Cappuccino Frother 13 Height-adjustable coffee spout 14 Cup platform

Control elements

2 3

Front left:

1 Plain text display

Q On/off button c Maintenance button i Espresso button o Coffee button v Pre-ground coffee button

Front right:

p Cappuccino button ü Milk foam button m Hot water button

4 Easy Cappuccino Frother 5 Professional Cappuccino Frother

6 Hot water nozzle 2 Rotary Switch cover 3 Rotary Switch

The Connector System© permits the use of different frothers. These are available from stockists.

Important information

Proper use

For your safety

The machine has been designed and built for domestic use. It should only be used to prepare coffee and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use.

Before using the machine always carefully read and comply with all these instructions. Keep this manual close to the IMPRESSA and, if appropriate, pass it on to the next user.

Please read and note carefully the following important safety information. By doing this, you can avoid the life-threatening danger of electric shock:

Z Never use a machine which has been damaged or with a

defective power cable.

Z For information on what to do in case of damage, for example

if there is a smell of burning, unplug the machine immedi ately from the mains supply and contact the JURA service centre.

Z If the power cable for this machine is damaged, it must be

repaired either directly by JURA or by a JURA approved service centre.

Z Make sure that the IMPRESSA and the power cable are not

located close to hot surfaces.

Z Be careful to ensure that the power cable does not get caught

and does not rub against sharp edges.

Z Never open and repair the machine yourself. Do not modify

the machine in any way that is not described in the IMPRESS A Manual. The machine contains live parts. If opened, there is a danger of serious injury. Repairs may only be carried out by JURA approved service centres, using original spare parts and accessories.

There is a risk of scalds or burns on the spouts or on the nozzle:

Z Place the machine out of the reach of children. Z Do not touch any hot parts. Use the handles provided. Z Be careful to ensure that the appropriate nozzle is installed

and clean. The nozzle or parts of the nozzle might come off if the parts are not assembled correctly or a blockage occurs.

Important information

A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire:

Z Never allow the power cable to loo sely hang down. The pow er

cable can be tripped over or damaged.

Z Protect your IMPRESSA from environmental influences such

as rain, frost and direct sunlight.

Z Do not put the IMPRESSA, cable or connections in water. Z Do not put the IMPRESSA or any individual parts in the dish-

washer.

Z Turn your IMPRESSA off at the power switch before starting

any cleaning operation. Always wipe your IMPRESSA with a

damp cloth rather than a wet one, and protect it from pro-

longed water splash.

Z Only connect the machine to a power supply in accordance

with the information on the rating plate. The rating plate is

located on the underside of your IMPRESSA. Further technical

data is given in Chapter 10 ‘Technical Data’.

Z Use only original JURA care products. Use of accessories that

are not explicitly recommended by JURA could damage the

IMPRESSA.

Z Do not use any coffee beans treated with additives or caramel-

ised coffee beans.

Z Always fill the water tank with cold, fresh mains water. Z If you will be absent for an extended period, turn the machine

off and unplug.

Risk to children and persons with limited capabilities in operating machines:

Z The machine is not designed to be operated by children and

persons with limited capabilities.

Z The machine may only be used by persons who are able to

operate the machine safely.

Safe handling of the CLARIS filter cartridges:

Z Filter cartridges should be kept out of the reach of children. Z Store filter cartridges dry in the sealed package. Z Protect filter cartridges from heat and direct sunlight. Z Do NOT use damaged filter cartridges. Z Do NOT open filter cartridges.

The IMPRESSA C9 Manual

You are holding the manual for yo ur IMPRESSA C9 in your hand. It will help you to familiarize yourself with your IMPRESSA safely and quickly and teach you the full range of facilities it offers.

Chapter 2, ‘Preparing and using your IMPRESSA for the first time’, explains step-by-step how to set up and prepare the IMPRESSA.

Chapter 3, ‘Familiarising yourself with the control options’ is important for you to read as you are familiarising yourself with your IMPRESSA. It invites you to actively explore all the different coffee experiences that it offers.

All the other chapters are intended to help you when you have a specific query.

If you use the IMPRESSA C9, you will become a mast er at preparing exciting coffee specialities, you will be a Barista!

You can download the short operating instructions for y our machine from the JURA website (www.jura.com).

Symbol description

Warnings

Always take note of any inf ormation marked with the CAUTION or W ARNING symbol. The signal word WARNING points out potential risk of serious injury, and the signal

CAUTION CAUTION

Symbols used

word CAUTION potential risk of slight injury. The CAUTION symbol is used to draw attention to circumstances whic h c ould cause

the machine to become damaged.

Information and tips to make things easier for you as you use your IMPRESSA. References to the online JURA website, where you can find interesting further infor-

mation: www.jura.com. Prompt to take action. This symbol means that you are being prompted to perform

some action.

1 IMPRESSA C9

Coffee that fulfils your wildest dreams

The new entry level model in the One Touch Cappuccino league is sure to please all cappucino fans with its simple ‘touch of a button’ function without having to move the cup. In elegant piano black and with a new user interface, the high-quality IMPRESSA C9 is fully in keeping with current trends and exudes an aura of superiority, dur ability and competence. It impressively demonstrates these attribut es with each coffee speciality that you enjoy.

Z One Touch Cappuccino: Your IMPRESSA C9 makes a cup of

cappuccino at the touch of a button, without you having to

move the cup. Hot milk foam, flowing int o the cup and slowly

starting to fill it. Steam which rises, awakening the anticipa-

tion of a delicious speciality. Aromatic coffee, blending with

the milk, pushing up the milk foam topping. These are the

protagonists in a sensuous drama – the drama of perfect cof-

fee preparation.

Z Simple operation: With the clearly arranged control elements

and the easy-to-understand text and graphic display, opera-

tion of the IMPRESSA C9 is also simple for beginners. Y ou can

navigate effectively through the individual programme steps

by simply turning and pressing the Rotary Switch. The focus

is on your personal taste. Simply select the coffee strength,

amount of water and temperature according to yo ur individ-

ual preferences.

Z Energy-saving mode (Energy Save Mode, E.S.M.© ): The

IMPRESSA C9 actively assists you in saving energy. With the

energy-saving mode you can adjust the energy-saving poten-

tial to suit the way you like to enjoy your beverages. The

machine can be completely disconnected from the power

supply at the main switch – for instance if you are going to be

absent for some time.

1 IMPRESSA C9

Z Height-adjustable coffee spout: The height of the coffee

spout, which can be adjusted within a range of 65 to 111 mm, can be adapted to all cup sizes on a continuous scale. This prevents coffee splashing on the machine and is your guarantee for a rich, thick crema.

Connector System©

JURA on the Internet

Knowledge Builder

The Connector System frothers:

Z Professional Cappuccino Frother

U Cappuccino, latte macchiato U Hot milk and milk foam

Z Easy Cappuccino Frother

U Cappuccino U Milk foam

Visit us on the Internet.

@ At www.jura.com you will find interesting and up-to-date

information on your IMPRESSA and on every aspect of coffee.

You can familiarise y ourself with y our IMPRES S A C9 in a fun way on the PC.

@ The Knowledge Builder awaits you at www.jura.com. The

interactive assistant, LEO, will support you and explain the benefits of and how to use your IMPRESSA.

permits the use of different cappuccino

2 Preparing and using for the first time

This chapter provides you with the information y ou need to use your IMPRESSA without any problems. You will prepare your IMPRESSA step-by-step for your first coffee experience.

2 Preparing and using your IMPRESSA for the first time

Set up

Filling the water tank

CAUTION

Filling the bean container

CAUTION

Keep the packaging for your IMPRES SA. It should be used to protect the machine during transportation.

When setting up your IMPRESSA, please note the following:

Z Set the IMPRESSA down on a horizontal surface that is not

sensitive to water.

Z Choose a spot for your IMPRESSA which is protected against

overheating.

To enjoy perfect coffee we recommend changing the water every day.

Milk, mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Remove the water tank and rinse it with cold water. T Fill the water tank with fresh, cold water and reinsert.

The bean container has an aroma preservation cover . This will ensure that your coffee beans retain their aroma for longer.

Coffee beans which have been treated with additives (e.g. sugar), pre-ground or freeze-dried coffee will damage the grinder.

T Only use untreated coffee beans to refill the bean container.

T Open the cover of the bean container and remove the aroma

preservation cover.

T Remove any dirt or foreign objects inside the bean con-

tainer.

T Fill the bean container with coffee beans, then close the

aroma preservation cover and the bean container cover.

2 Preparing and using your IMPRESSA for the first time

First-time use

If the machine is operated with a defective power cable, there is a danger of electric shock.

WARNING

T Never use a machine which has a defective power cable.

Precondition: The water tank and bean container are full.

T Insert the mains plug into a power socket.

3 T Swit ch on the IMPRESSA using the po wer switch on the back

of the machine. The indicator light lights up (standby).

Q T Press the On/Off button to switch the IMPRESSA on.

The pre-set language appears on the display.

T Open the cover of the Rotary Switch.

The Rotary Switch lights up.

g T Turn the Rotary Switch until the desired language is dis-

played. For Example:

k T Press the Rotary Switch to confirm the language.

OK appears briefly on the display to confirm the setting. PRESS RINSE, the maintenance button c lights up.

T Close the cover of the Rotary Switch. T Place a receptacle under the frother.

c T Press the maintenance button.

SYSTEM FILLING, the system fills up with water. A

small amount of water flows from the frother. This operation stops automatically , the following appears on the display:

PRESS RINSE, the maintenance button c lights up.

T Place a receptacle under the coffee spout.

c T Press the maintenance button.

RINSING, the machine rinses. The operation stops auto-

matically.

READY, your IMPRESSA is ready to use.

LANGUAGE ENGLISH

HEATING.

2 Preparing and using your IMPRESSA for the first time

E When a coffee speciality has been prepared for the first time,

it is possible that

the grinder has not yet been completely filled with coffee

beans. In this case prepare another coffee speciality.

FILL BEANS is shown on the display as

Using and activating filter

Your IMPRES SA no longer has to be descaled if you are using CLARIS filter cartridges.

@ Y ou can also try out the ‘Insert filter’ operation online. Visit the

Knowledge Builder at www.jura.com.

E Perform the ‘Insert filter’ operation without interruptions. This

will ensure that your IMPRESSA always produces at its best.

Precondition:

k T Keep the Rotary Switch pressed until

g T Turn the Rotary Switch until FILTER - is displayed. k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears on

the display.

NO -

g T Turn the Rotary Switch until YES w is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting. INSERT, the maintenance button c lights up.

T Close the cover of the Rotary Switch. T Remove the CLARIS filter cartridge from the Welcome Pack. T Remove the water tank and empty it. T Lift the cartridge holder and insert the filter car tridge into

the water tank, applying slight pressure. T Close the cartridge holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert.

2 Preparing and using your IMPRESSA for the first time

T Place a receptacle (at least 500 ml) under the frother.

c T Press the maintenance button.

FILTER RINSING. Water will flow out of the frother.

E You can interrupt rinsing of the filter at any time by pressing

any button.

E The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Filter rinsing stops automatically after approx. 500 ml.

HEATING appears on the display, then READY is dis-

played. The filter is now activated.

Determining water hardness and adjusting

E However, if you are using the CLARIS filter cartridge and have

activated it, you will not be able to adjust the water hardness.

The harder the water is, the more frequently the IMPRESSA needs to be descaled. It is therefore important to adjust the water hardness.

The water hardness can be adjusted on a continuous scale between 1° dH and 30° dH. This can also be deactivated, which means that the IMPRESSA will not let you know when it has to be descaled. You can find out what the w at er hardness is by using the Aquadur® test strip supplied as standard.

T Hold the test strip briefly (for one second) under flowing

water. Shake off the water. T Wait for about one minute. T You will then be able to read the degree of water hardness

from the discolouration of the Aquadur® test strip and the

description on the packaging.

You can now adjust the water hardness.

Example: To change the water hardness from

16°dH to

25°dH, proceed as follows:

Precondition:

k T Keep the Rotary Switch pressed until

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

2 Preparing and using your IMPRESSA for the first time

g T Turn the Rotary Switch until HARDNESS is displayed. k T Press the Rotary Switch to enter the programme item.

16°dH

g T Turn the Rotary Switch until 25°dH is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting.

g T Turn the Rotary Switch until k T Press the Rotary Switch to exit programming mode.

EXIT is displayed.

READY appears on the display.

T Close the cover of the Rotary Switch.

Adjusting the grinder

CAUTION

You can adjust the grinder continuously to suit the roast of y our coffee.

If you adjust the fineness of grind when the grinder is not operating, the grinding wheel could be damaged.

T Only adjust the fineness of grind when the grinder is run -

ning.

The fineness of grind setting is correct if the coffee flows regularly from the coffee spout. A fine, thick crema is also formed. Our recommendations:

Z Select a fine setting for a light roast.

U If the fineness of grind setting is too fine, the coffee only

drips from the coffee spout.

Z Select a coarse setting for a darker roast.

U If the fineness of grind is too coarse the coffee flows too

quickly from the coffee spout.

Example: T o change the fineness of grind during coffee preparation, proceed as follows:

T Open the cover of the bean container. T Remove the aroma preservation cover. T Place a cup under the coffee spout.

2 Preparing and using your IMPRESSA for the first time

o T Press the Coffee button.

The grinder starts and

the coffee strength is briefly displayed. T Turn the fineness of grind switch to the desired position

while the grinder is running.

The coffee will be prepared and the fineness of grind is

adjusted. T Close the aroma preservation cover and the cover of the

bean container.

1 COFFEE is displayed. After this,

Switching on

Switching off (standby)

Precondition: Your IMPRESSA is switched on at the power switch

and the indicator light is illuminated (standby). Q T Press the On/Off button to switch the IMPRESSA on.

HEATING is displayed.

PRESS RINSE, the maintenance button c lights up.

T Place a receptacle under the coffee spout.

c T Press the maintenance button.

RINSING, the machine rinses.

Preparation stops automatically.

display.

When you switch your IMPRESS A off, the spouts with which a coffee speciality or milk have been prepared are rinsed.

T Place a receptacle under the coffee spout and the frother.

Q T Press the On/Off button.

E When you prepare a milk product, but have not performed

cappuccino cleaning, tenance button c lights up. For ten seconds y ou can start the ’Clean cappuccino frother’ procedure by pressing the maintenance button.

C–CLEANING appears and the main-

READY appears on the

RINSING, the coffee spout is rinsed.

RINSE RIGHT, maintenance button c lights up.

2 Preparing and using your IMPRESSA for the first time

c T Press the maintenance button.

RINSING appears on the display, and the right coffee

spout is rinsed.

CAPPUCCINO RINSING

Cappuccino rinsing starts, and then stops automatically. The IMPRESSA is switched off (standby), and the indicator light lights up.

E When your IMPRESSA is switched off, a hissing noise may be

audible. This is normal and does not have any effect on the machine.

3 Familiarising yourself with the control options

With the IMPRESSA, you can prepare an excellent coffee or milk speciality at the touch of a button. You also ha ve the option of adjusting the coffee strength and temperature, as w ell as the amount of water to your personal taste.

This chapter will allow you to become familiar with all c ontrol options with the aid of examples. T o familiarise yourself with your IMPRESSA, we recommend that you make a point of actively trying the facilities described in this chapter. You will find this is well worthwhile.

Learn how to perform the following:

Z Preparation at the touch of a button Z One-off settings before and while your drink is being pre-

pared.

Z Adjusting the default amount of water to suit the cup size Z Permanent settings in programming mode

E You can stop the machine at any time while a coffee or milk

speciality or hot water is being prepared. T o do this, press any

button.

@ If you prefer to familiarise yourself with your IMPRESSA in a

fun way on the computer, the interactive Knowledge Builder

tutorial programme can be found on the Internet at

www.jura.com.

3 Familiarising yourself with the control options

Preparation at the touch of a button

Preparing a coffee speciality at the touch of a button

Preparing two coffee specialities at the touch of one button

Prepare your favourite coffee speciality at the touch of a button.

All coffee specialities are prepared following this model at the touch of a button.

Example: This is how to prepare one espresso. Precondition:

i T Press the Espresso button.

READY is displayed.

T Place an espresso cup under the coffee spout.

1 ESPRESSO and the coffee strength is then briefly dis-

played. The pre-set amount of water flows into the cup. Preparation stops automatically.

Example: This is how to prepare two espressi. Precondition:

i T Press the Espresso button twice (within two seconds).

READY is displayed.

T Place two espresso cups under the coffee spout.

READY appears on the display.

2 ESPRESSI appears on the display, the pre-set amount

of water flows into the cups. Preparation stops automatically. display.

READY appears on the

One-off settings before and during preparation

The coffee strength can be changed before preparation or during the grinding operation. The following coffee strengths can be selected for 1 espresso, 1 coffee and 1 cappuccino:

Z Mild Z Normal Z Strong

E The pre-set amount of water can be changed during the

brewing operation by turning the Rotary Switch.

One-off settings before and during coffee preparation always follo w this model. These settings are not saved.

3 Familiarising yourself with the control options

Changing the coffee strength before preparation

Changing the amount of water during preparation

Example: Proceed as follows to to prepare a strong cup of coffee. Precondition:

g T Turn the Rotary Switch until o T Press the Coffee button for as long as

READY is displayed.

T Open the cover of the Rotary Switch. T Place a cup under the coffee spout.

STRONG is displayed.

STRONG is dis-

played.

1 COFFEE / STRONG.

The pre-set amount of water flows into the cup. Preparation stops automatically.

T Close the cover of the Rotary Switch.

Example: Proceed as follows to prepare a Precondition:

o T Press the Coffee button.

g T Turn the Rot ary Switch during the brewing operation until

READY is displayed.

T Open the cover of the Rotary Switch. T Place a cup under the coffee spout.

The grinding operation starts. strength is then briefly displayed.

READY appears on the display.

110 ML cup of coffee.

1 COFFEE and the coffee

110 ML is displayed.

The set amount of water flows into the cup. Preparation stops automatically.

T Close the cover of the Rotary Switch.

READY appears on the display.

Adjusting the default amount of water to suit the cup size

It is easy to make permanent settings for the amount of water for all coffee and milk specialities as well as hot water according t o the cup size. As in the following example, adjust the amount of water once. Every time you prepare a drink in the future, this amount of water will be dispensed.

The permanent settings for adapting the amount of water to to the cup size for all coffee and milk specialities as well as hot w ater follo w this model.

Example: T o make permanent settings f or the amount of water for an espresso, proceed as follows: Precondition:

READY is displayed.

3 Familiarising yourself with the control options

T Place an espresso cup under the coffee spout.

i T Press and hold the Espresso button.

1 ESPRESSO appears on the display.

i T Hold the Espresso button down until

ENOUGH

COFFEE ? appears.

i T Release the Espresso button.

Coffee preparation will start and the espresso will flow into the cup.

T Press any button as soon as enough espresso has flowed

into the cup. Preparation stops automatically. display. The set amount of w ater f or an espresso will be permanently stored.

E You can alter these settings at any time by repeating the

above procedure.

READY appears on the display.

OK appears briefly on the

Permanent settings in programming mode

Programme item Sub-item

RINSE

BUTTONS

FILTER - YES w

C–CLEANING, FILTER (only when the

filter is activated),

CLEAN, C–RINSE, DE-SCALE (only when

the filter is not activated),

CLEAN

SELECT BUTTON

NO -

You can easily adjust y our IMPRESS A to y our personal coffee blends and specialities. You can navigate through the easy-tounderstand programme steps and make permanent settings by simply turning and pressing the Rotary Switch.

You can make the following settings with the Rotary Switch:

Explanation

T Select the desired maintenance pro- gramme. If no action is taken, programming mode is exited automatically after approx. five seconds.

T Select your settings for the coffee and milk specialities and hot water.

T Indicate whether you operate your IMPRESSA with or without a CLARIS filter cartridge.

3 Familiarising yourself with the control options

Programme item Sub-item Explanation

HARDNESS (is only

displayed when the filter is not activated)

ENERGY

INACTIVE, 1°dH – 30°dH

SAVE -,

T Adjust the water hardness.

T Select an energy-saving mode.

SAVE w

TIME --:--

UNIT ON --:--

OFF AFTER

INACTIVE

0.5 HRS – 15 HRS

INFO

DISPLAY

ML/OZ,

24H/AM PM

LANGUAGE

EXIT

Settings in programming mode always follow the same model.

T Set the time. T Adjust the switch-on time. T Set the number of hours after which the

IMPRESSA should switch off automatically.

T Keep track of all prepared coffee and milk specialities and view the maintenance status.

T Select the unit of the amount of water and the time format.

T Select your language.

T Exit programming mode.

Example: To change the strength of one espresso from

NORMAL proceed as follows:

Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

BUTTONS is displayed.

STRONG

SELECT BUTTON

E Next select the product button for which you would like to

make settings. No product is prepared during this procedure.

E To enter a setting for the double product, press the corre-

sponding button twice within a period of two seconds.

i T Press the Espresso button.

WATER

3 Familiarising yourself with the control options

g T Turn the Rotary Switch until STRENGTH is displayed. k T Press the Rotary Switch to enter the programme item.

STRONG

g T Turn the Rotary Switch until NORMAL is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting.

STRENGTH

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

BUTTONS

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

T Close the cover of the Rotary Switch.

Query information and maintenance status

Under the programme item information:

Z Number of the prepared coffee and milk specialities and hot

water

Z Maintenance status and number of maintenance programmes

performed (cleaning, descaling, filter change)

Z Number of performed cappuccino cleaning operations

Precondition:

k T Press the Rotary Switch until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

INFO, you can query the following

RINSE appears.

INFO is displayed.

BUTTONS

k T Press the Rotary Switch to enter the programme item.

The total number of the prepared coffee specialities is displayed.

E The respective number of prepared products is displayed by

pressing the individual buttons.

k T Press the Rotary Switch to exit the programme item.

BUTTONS

3 Familiarising yourself with the control options

g T Turn the Rotary Switch until CLEAN is displayed.

k T Press the Rotary Switch to enter the programme item.

k T Press the Rotary Switch to exit the programme item.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

E Turn the Rotary Switch to switch to the performed descaling,

filter change and cappuccino cleaning operations.

The number of performed cleaning operations appears on the display.

E The respective maintenance status can also be displayed in

addition to the number of performed maintenance programmes. The filled out fields show the maintenance status. Once all fields are filled out, your IMPRESSA will request the respective maintenance programme.

CLEAN

INFO

READY

T Close the cover of the Rotary Switch.

4 Preparation at the touch of a button

In this chapter you will find out how to prepare coffee and milk specialities and hot water without making further settings.

Chapter 3, ‘Familiarising yourself with the control options ’, will teach you how to adjust the settings to your personal preferences. Alternatively, you can use Chapter 5, ‘Permanent settings in programming mode’.

E You can interrupt the machine at any time while a coffee or

milk speciality or hot water is being prepared. T o do this, press any button.

E During preparation, you can change the set amount by turn-

ing the Rotary Switch.

@ You can also try out the preparation of coffee specialities

online. Visit the Knowledge Builder at www.jura.com.

4 Preparation at the touch of a button

Espresso

The classic coffee drink from Italy. There is a definite crema on the surface of the espresso.

Example: This is how to prepare an espresso.

T Place an espresso cup under the coffee spout.

i T Press the Espresso button.

1 ESPRESSO and the coffee strength is then briefly dis-

played. The pre-set amount of water flows into the cup. Preparation stops automatically.

To prepare two cups of espresso: Plac e two espresso cups under the coffee spout and press the espresso button i twice (within two

seconds).

READY appears on the display.

4 Preparation at the touch of a button

Coffee

Cappuccino

Cappuccino with the Easy Cappuccino Frother

Example: This is how to prepare a coffee.

T Place a cup under the coffee spout.

o T Press the Coffee button.

1 COFFEE is displayed. After this, the coffee strength is

briefly displayed. The pre-set amount of water flows into the cup. Preparation stops automatically.

To prepare two cups of c offee: Place two cups under the coffee spout and press the coffee button o twice (within two seconds).

Your IMPRES SA prepares a cappucc ino at the touch of a butt on. It is not necessary to move the cup.

E The IMPRESSA C9 is equipped with a heating element for pre-

paring coffee and steam. After preparing several cappuccino s within a short period of time, it is possible that the coffee only flows irregularly from the right-hand coffee spout. In this case allow your IMPRESSA a short break before making the next cappuccino.

T Take the protective cover off the Easy Cappuccino Frother. T Attach the milk pipe to the frother. T Insert the other end of the milk pipe into a milk carton or

connect it to a milk container.

READY appears on the display.

T Place a cup under the frother.

p T Press the Cappuccino button.

CAPPUCCINO, the coffee strength is then briefly dis-

played.

CAPPUCCINO, the milk foam is prepared.

The operation stops automatically. Coffee preparation will now begin.

Cappuccino with the Professional Cappuccino Frother

4 Preparation at the touch of a button

Preparation stops automatically after reaching the pre-set amount of water.

To ensure that the Easy Cappuccino Frother works perfectly, it should be rinsed and cleaned regularly (refer to Chapter 6 ‘Maintenance – Easy Cappuccino Frother’).

T Take the protec tive cover off the Professional Cappuccino

Frother. T Attach the milk pipe to the frother. T Insert the other end of the milk pipe into a milk carton or

connect it to a milk container.

T Place a cup under the frother. T Turn the selection lever of the frother t o the milk foam posi-

tion p.

p T Press the Cappuccino button.

READY appears on the display.

CAPPUCCINO, the coffee strength is then briefly dis-

played.

CAPPUCCINO, the milk foam is prepared.

The operation stops automatically. Coffee preparation will

now begin.

Preparation stops automatically after reaching the pre-set

amount of water.

READY appears on the display.

To ensure that the Professional Cappucc ino Frother works perfectly, it should be rinsed and cleaned regularly (refer to Chapter 6 ‘Maintenance – Professional Cappuccino Frother’).

4 Preparation at the touch of a button

Pre-ground coffee

You can choose a second coffee blend with the filler funnel for preground coffee.

E Never add more than two level measuring spoons of pre-

ground coffee.

E Use pre-ground coffee which is not ground too finely. Very

fine coffee can block up the system so that the coffee only comes out in drips.

E If you did not fill the machine with a sufficient amount of pre-

ground coffee, and the IMPRESSA stops operation.

E The desired coffee speciality must be prepared within approx.

one minute after filling with the pre-ground coffee. Otherwise, the IMPRESSA stops the operation and is ready to use again.

All coffee specialities with pre-ground coffee are prepared following this model.

Example: This is how to prepare a cup of coffee using pre-ground coffee.

T Place a cup under the coffee spout.

v T Press the Pre-ground coffee button.

NOT ENOUGH PRE-GROUND is displayed

FILL PRE-GROUND, then READY are displayed.

T Open the cover of the filler funnel for pre-ground coffee. T Place one level measuring spoon of pre-ground coffee into

the filler funnel.

T Close the cover of the filler funnel for pre-ground coffee.

o T Press the Coffee button.

1 COFFEE is displayed. After this, PRE-GROUND is

briefly displayed. Preparation stops automatically after reaching the pre-set amount of water.

READY

Foaming milk with the Easy Cappuccino Frother

4 Preparation at the touch of a button

T Take the protective cover off the Easy Cappuccino Frother. T Attach the milk pipe to the frother. T Insert the other end of the milk pipe into a milk carton or

connect it to a milk container.

T Place a cup under the frother.

ü T Press the milk foam button.

HEATING

READY appears as soon as the IMPRESSA has heated up.

ü T Press the milk foam button once more.

MILK, the milk foam is being prepared.

Preparation stops automatically.

READY

E You can prepare more milk foam within about 40 seconds.

Foaming and heating milk with the Professional Cappuccino Frother

To ensure that the Easy Cappuccino Frother works perfectly, it should be rinsed and cleaned regularly (refer to Chapter 6 ‘Maintenance – Easy Cappuccino Frother’).

T Take the protec tive cover off the Professional Cappuccino

Frother. T Attach the milk pipe to the frother. T Insert the other end of the milk pipe into a milk carton or

connect it to a milk container.

4 Preparation at the touch of a button

T Place a cup under the frother. T Turn the selection lever of the frother t o the milk foam posi-

tion p.

E If you want to heat the milk, set the selection lever of the

frother to the milk position t.

ü T Press the milk foam button.

HEATING

READY appears as soon as the IMPRESSA has heated up.

ü T Press the milk foam button once more.

MILK, the milk foam is being prepared.

Preparation stops automatically.

READY

E You can prepare more milk foam or hot milk within about

40 seconds.

To ensure that the Professional Cappucc ino Frother works perfectly, it should be rinsed and cleaned regularly (refer to Chapter 6 ‘Maintenance – Professional Cappuccino Frother’).

Hot water

CAUTION

Precondition:

E Attach the hot water nozzle to the Connector System© for

There is a danger of scalding from hot water splashes.

T Avoid direct contact with skin.

m T Press the hot water button.

READY is displayed.

heating water.

T Place a cup under the nozzle.

WATER, hot water flows into the cup.

Preparation stops automatically after reaching the pre-set amount of water.

READY

5 Permanent settings in programming mode

Products

Product Amount Coffee strength Temp.

1 espresso

25 ML – 240 ML MILD, NORMAL,

With the BUTTONS programme item you can enter individual set tings for all coffee and milk specialities as well as hot water.

The following permanent settings can be entered for coffee and milk specialities and hot water:

NORMAL, HIGH

STRONG

2 espressi 25 ML – 240 ML

(per cup)

1 coffees 25 ML – 240 ML MILD, NORMAL,

–

NORMAL, HIGH

STRONG

2 coffees 25 ML – 240 ML

(per cup)

Cappuccino Amount of milk:

3 SEC – 120 SEC

Amount of water:

–

MILD, NORMAL,

STRONG

NORMAL, HIGH

25 ML – 240 ML

Milk foam 3 SEC – 120 SEC –– Hot water

25 ML – 450 ML ––

Permanent settings in programming mode always follow the same model.

Example: Proceed as follows to change the amount of milk of one cappuccino from

14 SEC to 20 SEC, the amount of water from 60 ML to 50 ML and the coffee strength from NORMAL to STRONG.

Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

BUTTONS is displayed.

SELECT BUTTON

5 Permanent settings in programming mode

p T Press the Cappuccino button.

k T Press the Rotary Switch to enter the programme item.

g T Turn the Rotary Switch until 20 SEC is displayed. k T Press the Rotary Switch to confirm the setting.

g T Turn the Rotary Switch until WATER is displayed. k T Press the Rotary Switch to enter the programme item.

f T Turn the Rotary Switch until 50 ML is displayed. k T Press the Rotary Switch to confirm the setting.

g T Turn the Rotary Switch until STRENGTH is displayed. k T Press the Rotary Switch to enter the programme item.

g T Turn the Rotary Switch until STRONG is displayed. k T Press the Rotary Switch to confirm the setting.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

E Next select the product button for which you would like to

make settings. No product is prepared during this procedure.

E To change a setting for a double product, press the corre-

sponding button twice within a period of two seconds.

MILK

14 SEC

OK appears briefly on the display to confirm the setting.

MILK

60 ML

OK appears briefly on the display.

WATER

NORMAL

OK appears briefly on the display.

STRENGTH

BUTTONS

READY

T Close the cover of the Rotary Switch.

5 Permanent settings in programming mode

Resetting the products to works settings

Energy-saving mode

You can reset the v alues of all products individually to the works setting.

Example: Proceed as follows to reset the values of 1 espresso and 2 espressi to the works setting. Precondition: The IMPRESSA must be switched off (standby).

T Press the Rotary Switch and the Espresso button for two sec -

onds at the same time until The values of 1 espresso and 2 espressi are then reset to the works setting. The IMPRESSA must be switched off (standby).

An energy-saving mode (Energy Save Mode, E.S.M. setting can be made with the

Z SAVE -

U All coffee product s as well as hot water can be prepared

without having to wait.

U The machine heats up before preparing cappuccino or

milk.

Z SAVE w

U Approx. 5 minutes after the last preparation the IMPRESSA

switches to the energy-saving temperature and is not ready for use.

U Before coffee, hot water or milk can be prepared, the machine

heats up.

OK appears.

) permanent

ENERGY programme item:

Example: Proceed as follows to change the energy-saving mode from

SAVE - to SAVE w.

Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

ENERGY - is displayed.

SAVE -

g T Turn the Rotary Switch until SAVE w is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting.

ENERGY w

5 Permanent settings in programming mode

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

T Close the cover of the Rotary Switch.

Time

Programmable switch-on time

If the machine is disconnected from the mains, the time has to be reset. Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

TIME is displayed.

--:--

g T Turn the Rotary Switch to set the hour. k T Press the Rotary Switch to confirm the hour setting. g T Turn the Rotary Switch to set the minutes. k T Press the Rotary Switch to confirm the minute setting.

OK appears briefly on the display to confirm the setting.

TIME

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

T Close the cover of the Rotary Switch.

When a switch-on time has been set, the IMPRESSA switches on every day at the set time and heats up.

E The programmable switch-on time can only be set when the

time has been set.

E The programmable switch-on of your IMPRESSA only works

when the machine is switched on at the power switch (standby).

Example: T o set the programmable switch-on time to

ceed as follows. Precondition:

k T Keep the Rotary Switch pressed until

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

07:30, pro-

5 Permanent settings in programming mode

g T Turn the Rotary Switch until UNIT ON appears. k T Press the Rotary Switch to enter the programme item.

--:--

g T Turn the Rotary Switch until 07:00 is displayed. k T Press the Rotary Switch to confirm the hour setting. g T Turn the Rotary Switch until k T Press the Rotary Switch to confirm the minute setting.

07:30 is displayed.

OK appears briefly on the display to confirm the setting.

UNIT ON

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

READY

T Close the cover of the Rotary Switch.

Automatic switch-off

By instructing your IMPRESSA to automatically switch itself off, y ou can cut down your energy consumption. If this function is activated, your IMPRESSA switches off automatically after a pre-set period has elapsed following the last use of the machine.

E The programmable switch-off time can be adjusted between

0.5 and 15 hours or deactivated.

Example: Proceed as follows to change the automatic switch-off time from Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

1 HRS to 2 HRS.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

OFF AFTER is displayed.

1 HRS

f T Turn the Rotary Switch until 2 HRS is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting.

OFF AFTER

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

T Close the cover of the Rotary Switch.

5 Permanent settings in programming mode

Unit amount of water / Time format

You can change the unit of the amount of w ater from ‘ml’ to ‘ oz’ and the time format to ‘24 HRS’ or ‘AM/PM’ .

Example: To change the unit for the amount of water from

ML to

OZ, proceed as follows.

Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

DISPLAY is displayed.

ML/OZ

E To change the time format, turn the Rotary Switch until

24H/AM PM is displayed.

k T Press the Rotary Switch to enter the programme item.

g T Turn the Rotary Switch until OZ is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting.

ML/OZ

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit the programme item.

DISPLAY

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

READY

T Close the cover of the Rotary Switch.

Language

The language of your IMPRESSA is set with this programme item.

Example: T o change the language from proceed as follows. Precondition:

k T Keep the Rotary Switch pressed until g T Turn the Rotary Switch until

READY is displayed.

T Open the cover of the Rotary Switch.

ENGLISH to DEUTSCH,

RINSE appears.

LANGUAGE is displayed.

5 Permanent settings in programming mode

k T Press the Rotary Switch to enter the programme item.

ENGLISH

g T Turn the Rotary Switch until DEUTSCH is displayed. k T Press the Rotary Switch to confirm the setting.

OK appears briefly on the display to confirm the setting.

SPRACHE

g T Turn the Rotary Switch until EXIT is displayed. k T Press the Rotary Switch to exit programming mode.

BEREIT

T Close the cover of the Rotary Switch.

6 Maintenance

Your IMPRESSA has the following integrated maintenance programmes:

Z Rinse machine Z Filter change Z Clean machine Z Descale machine Z Rinse frother Z Clean frother

E Clean or descale the machine or change the filter whenever

the appropriate indicator lights up.

Maintenance tips

Rinse machine

To ensure that you get many years of reliable service out of your IMPRESSA and to guarantee the optimum coffee quality, the machine requires daily maintenance.

You should proceed as follows:

Z Empty the coffee grounds container and the drip tray. Rinse

them with warm water.

Z Rinse the water tank with clean water. Z Dismantle and rinse the frother (See Chapter 6 ‘Mainte-

nance – Rinsing the frother’).

Z Wipe the surface of the machine with a damp cloth.

When the IMPRESSA is switched on, a prompt to perform a rinse operation automatically appears after heating. When the IMPRESSA is switched off, each spout which was used for preparation is rinsed.

You can initiate the rinse operation manually at any time. Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Place a receptacle under the coffee spout. T Open the cover of the Rotary Switch.

RINSE appears.

C–CLEANING

g T Turn the Rotary Switch until RINSE is displayed.

6 Maintenance

k T Press the Rotary Switch to initiate the rinse operation.

RINSING

Rinsing stops automatically and your IMPRESSA is then ready for use.

T Close the cover of the Rotary Switch.

Filter change

Change following a prompt

E After 50 litres of water have flowed through, or after two

months, the filter will cease to work. Y our IMPRESS A will automatically prompt you to change the filter.

E If the CLARIS filter cartridge is not activated, you will not be

prompted to change the filter.

@ You can also try out ‘changing the filter’ online. Visit the

Knowledge Builder at www.jura.com.

To change the CLARIS filter cartridge when prompted to do so by your IMPRESSA, proceed as follows:

Precondition: nance button c lights up. c T Press the maintenance button.

READY / FILTER is displayed and the mainte-

CHANGE

T Remove the water tank and empty it. T Open up the cartridge holder and remove the old CLARIS fil-

ter cartridge.

T Insert a new CLARIS filter cartridge into the water tank,

pressing it slightly. T Close the cartridge holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert.

T Place a receptacle (at least 500 ml) under the frother.

E If you are using the Professional Cappuccino Frother, set the

selection lever of the frother to the steam position n.

c T Press the maintenance button.

FILTER RINSING – Water will flow out of the frother.

6 Maintenance

E You can interrupt f ilter r insing at any tim e. To do this, press

any button.

E The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Filter rinsing stops automatically after approx. 500 ml. The IMPRESSA heats up and is once again ready to use.

Manual filter change

Clean machine

CAUTION

You can initiate the ‘Changing the filter’ operation manually.

Precondition: The filter is activated and

T Open the cover of the Rotary Switch.

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

RINSE appears.

C CLEANING

g T Turn the Rotary Switch until FILTER is displayed. k T Press the Rotary Switch.

CHANGE

T Close the cover of the Rotary Switch. T Continue with the second prompt to take action (indi-

cated by a T), as is described under ‘Change following a

prompt’.

After 200 coffee preparations or 80 switch-on rinses, the IMPRESSA will prompt you to clean it.

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.

T Use only original JURA care products.

E The cleaning programme only lasts about 20 minutes. E Do not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

E JURA cleaning tablets are available from stockists.

@ Y ou can also try out the ‘clean machine’ oper ation online. Visit

the Knowledge Builder at www.jura.com.

6 Maintenance

Cleaning following a prompt

Precondition: READY / CLEAN is display ed and the maintenance

button c lights up. c T Press the maintenance button.

EMPTY TRAY

T Empty the drip tray and coffee grounds container and put

them back into the machine.

PRESS RINSE, the maintenance button c lights up.

T Place a receptacle under the coffee spout and the frother.

c T Press the maintenance button.

CLEANING, water flows from both coffee spouts.

The process is interrupted, T Open the cover of the filler funnel for pre-ground coffee.

T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel.

c T Press the maintenance button.

ADD TABLET.

CLEANING, water flows from both coffee spouts several

times.

The process is interrupted – T Empty the drip tray and coffee grounds container and put

them back into the machine.

The cleaning operation is now complete. The IMPRESSA is

ready for use again.

EMPTY TRAY.

Manual cleaning

You can initiate the ‘Cleaning the machine’ operation manually. Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

C–CLEANING

g T Turn the Rotary Switch until CLEAN is displayed. k T Press the Rotary Switch.

EMPTY TRAY

T Close the cover of the Rotary Switch. T Continue with the second prompt to take action (indi-

cated by a T), as is described under ‘Cleaning following a

prompt’.

6 Maintenance

Descale machine

CAUTION

The IMPRESSA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the degree of hardness of your water.

If the descaling agent comes into contact with the skin or eyes, this can cause irritation.

T Avoid contact with the skin or eyes. T Rinse the descaling agent off with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.

T Use only original JURA care products.

If the descaling operation is interrupted, there may be damage to the machine.

T Allow the descaling program to run to the end.

If the descaling agent comes into contact with sensitive surfaces, damage cannot be ruled out.

T Clean up any splashes immediately.

E The descaling programme lasts approx. 45 minutes. E JURA descaling tablets are available from stockists. E If you use a CLARIS filter cartridge and this is activated, you

will not be prompted to change the filter.

Descaling following a prompt

@ You can also try out the ‘Descaling the machine’ operation

online. Visit the Knowledge Builder at www.jura.com.

Precondition: nance button c lights up. c T Press the maintenance button.

READY / DE-SCALE is displayed and the mainte-

EMPTY TRAY

T Empty the drip tray and coffee grounds container and put

them back into the machine.

AGENT IN TANK

T Remove the water tank and empty it.

T Completely dissolve the contents of one blister (3 JURA des-

caling tablets) in a container that holds 500 ml of water. This

may take several minutes. T Pour the solution into the empty water tank and insert it in

the machine.

AGENT IN TANK, the maintenance button c lights up.

T Remove the frother. T Place a receptacle (at least 500 ml) under the Connector Sys-

tem

c T Press the maintenance button.

DE-SCALING

eral times. The maintenance button blinks during the des-

caling operation.

The operation stops automatically,

EMPTY TRAY.

T Empty the receptacle under the Connector System T Empty the drip tray and coffee grounds container and put

them back into the machine.

FILL WATER TANK

T Remove the water tank and rinse it thoroughly. T Fill the water tank with fresh, cold mains water and rein-

sert.

PRESS RINSE, the maintenance button c lights up.

T Replace the frother. T Place a receptacle under the frother.

c T Press the maintenance button.

DE-SCALING, water flows out of the frother.

The operation stops automatically, T Empty the drip tray and coffee grounds container and put

them back into the machine.

The desc aling operatio n is now comple te. Your IMPRESSA

heats up and is once again ready to use.

EMPTY TRAY.

6 Maintenance

E If the descaling operation stops unexpectedly, rinse the wa ter

tank thoroughly.

6 Maintenance

Manual descaling

Rinsing the Easy Cappuccino Frother

Rinsing the Easy Cappuccino Frother after a prompt

You can initiate the ‘Descaling the machine’ operation manually.

Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed and the filter is not activated.

T Open the cover of the Rotary Switch.

RINSE appears.

C–CLEANING

g T Turn the Rotary Switch until DE-SCALE is displayed. k T Press the Rotary Switch.

EMPTY TRAY

T Close the cover of the Rotary Switch. T Continue with the second prompt to take action (indi-

cated by a T), as is described under ‘Descaling following a

prompt’.

To ensure that the Easy Cappuccino Frother works perfectly, you should rinse it with water whenever you have prepared some milk.

Your IMPRESSA will prompt you to rinse the Easy Cappuccino Frother 10 minutes after you have prepared milk.

Precondition: tenance button c lights up.

c T Press the maintenance button.

CAPPUCCINO RINSE is displayed and the main-

T Place a receptacle under the Easy Cappuccino Frother.

CAPPUCCINO RINSING, the frother is rinsed.

Preparation stops automatically. display.

READY appears on the

6 Maintenance

Rinsing the Easy Cappuccino Frother – starting manually

Cleaning the Easy Cappuccino Frother

CAUTION

You can initiate the ‘Rinsing the frother’ operation manually.

Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Place a receptacle under the Easy Cappuccino Frother. T Open the cover of the Rotary Switch.

RINSE appears.

C CLEANING

T Turn the Rotary Switch until C–CLEANING is displayed.

k T Press the Rotary Switch.

CAPPUCCINO RINSING, the frother is rinsed.

Preparation stops automatically.

display. T Close the cover of the Rotary Switch.

To ensure that the Easy Cappuccino Frother works perfectly, you should clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.

T Use only original JURA care products.

E The JURA Cappuccino Cleaner is available from stockists. E The IMPRESSA will not prompt you to clean the frother.

READY appears on the

@ You can also try out the ‘Cleaning the cappuccino frother’

operation online. Visit the Knowledge Builder at www.jura.com.

Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Remove the milk pipe from the milk carton/bottle or the

milk container. T Open the cover of the Rotary Switch.

RINSE appears.

C–CLEANING

k T Press the Rotary Switch.

CAPPUCCINO CLEANER

6 Maintenance

Disassembling and rinsing the Easy Cappuccino Frother

T Pour 250 ml of fresh water into a container and add one cap-

ful (max. 15 ml) of Cappuccino Cleaner. T Immerse the milk pipe in the receptacle. T Place another receptacle under the frother.

c T Press the maintenance button.

CLEANING, the frother and pipe are cleaned. The opera-

tion stops automatically.

WATER FOR CAPPUCCINO

T Rinse the re cept ac le th or oug hly, fi ll it wi th ap prox . 250 ml

of fresh water and immerse the milk pipe in the water. T Empty the other receptacle and place it under the frother

once more.

c T Press the maintenance button.

CLEANING, the frother and pipe are rinsed with fresh

water. The operation stops automatically.

READY appears on the display.

T Close the cover of the Rotary Switch.

T Carefully remove the frother from the Connector System

by twisting slightly. T Dismantle the frother completely. T Rinse all the frother parts thoroughly under running water. T Re-assemble the frother.

Rinsing the Professional Cappuccino Frother

E Ensure that the individual parts are correctly and firmly

attached to one another to ensure optimum function of the frother.

T Firmly attach the frother to the Connector System

To ensure that the Professional Cappucc ino Frother works perfectly, you should rinse it with water whenever you have prepared some milk.

6 Maintenance

Rinsing the Professional Cappuccino Frother after a prompt

Rinsing the Professional Cappuccino Frother – starting manually

Your IMPRESSA will prompt you to rinse the Professional Cappuccino Frother 10 minutes after you have prepared milk.

Precondition: tenance button c lights up.

c T Press the maintenance button.

CAPPUCCINO RINSE is displayed and the main-

T Place a receptacle under the Professional Cappuccino

Frother.

CAPPUCCINO RINSING, the frother is rinsed.

Preparation stops automatically. display.

You can initiate the ‘Rinsing the frother’ operation manually.

Precondition:

c T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Place a receptacle under the Professional Cappuccino

Frother.

T Open the cover of the Rotary Switch.

READY appears on the

RINSE appears.

C–CLEANING

T Turn the Rotary Switch until C–CLEANING is displayed.

k T Press the Rotary Switch.

CAPPUCCINO RINSING, the frother is rinsed with

fresh water. Preparation stops automatically. display.

T Close the cover of the Rotary Switch.

READY appears on the

Cleaning the Professional Cappuccino Frother

CAUTION

To ensure that the Professional Cappucc ino Frother works perfectly, you should clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged and/or traces of detergent could be left behind in the water.

T Use only original JURA care products.

6 Maintenance

E The JURA Cappuccino Cleaner is available from stockists. E The IMPRESSA will not prompt you to clean the frother.

@ You can also try out the ‘Cleaning the cappuccino frother’

operation online. Visit the Knowledge Builder at www.jura.com.

Precondition:

k T Keep the Rotary Switch pressed until k T Press the Rotary Switch to enter the programme item.

READY is displayed.

T Open the cover of the Rotary Switch.

RINSE appears.

C–CLEANING

k T Press the Rotary Switch.

CAPPUCCINO CLEANER

T Remove the milk pipe from the milk carton/bottle or the

milk container. T Pour 250 ml of fresh water into a container and add one cap-

ful (max. 15 ml) of Cappuccino Cleaner. T Immerse the milk pipe in the receptacle. T Turn the selection lever of the frother t o the milk foam posi-

tion p or milk t. T Place another receptacle under the frother.

c T Press the maintenance button.

CLEANING, the frother and pipe are cleaned. The opera-

tion stops automatically.

WATER FOR CAPPUCCINO

T Rinse the re cept ac le th or oug hly, fi ll it wi th ap prox . 250 ml

of fresh water and immerse the milk pipe in the water. T Empty the other receptacle and place it under the frother

once more.

c T Press the maintenance button.

CLEANING, the frother and pipe are rinsed with fresh

water.

Preparation stops automatically.

display. T Close the cover of the Rotary Switch.

READY appears on the

Disassembling and rinsing the Professional Cappuccino Frother

6 Maintenance

by twisting slightly. T Dismantle the frother completely. T Rinse all the frother parts thoroughly under running water. T Re-assemble the frother.

E Ensure that the individual parts are correctly and firmly

attached to one another to ensure optimum function of the frother.

Cleaning the bean container

WARNING

T Firmly attach the frother to the Connector System

Coffee beans may be covered with a slight oil film which remains on the walls of the bean container . These residues may negatively affect the coffee results. For this reason clean the bean container from time to time.

Danger of injury to the fingers when the grinder is running.

T Switch the machine off with the on/off button Q before per-

forming any work on the grinder.

T Switch the machine off at the power switch 3.

Precondition:

Q T Switch your machine off with the On/Off button. 3 T Switch your machine off at the power switch.

READY / FILL BEANS is displayed.

T Open the cover of the bean container and remove the aroma

preservation cover. T Clean the bean container with a soft, dry cloth. T Fill the bean container with coffee beans, then close the

aroma preservation cover and the bean container cover.

6 Maintenance

Descaling the water tank

Limescale deposits may form in the water tank. To ensure correc t function of the machine, descale the water tank from time to time.

T Remove the water tank. T If you use a CLARIS filter cartridge, remove this. T Descale the tank with a mild, commercially available descal-

ing agent in accordance with the instructions of the manu-

facturer. T Rinse out the water tank thoroughly. T If you use a CLARIS filter cartridge, insert this again. T Fill the water tank with fresh, cold water and reinsert.

7 Display messages

Message Cause/Result Action

FILL WATER TANK

EMPTY GROUNDS

TRAY MISSING

PRESS RINSE

FILL BEANS

CAPPUCCINO RINSE

The water tank is empty. You cannot prepare any coffee or milk specialities or hot water.

The coffee grounds container is full. You cannot prepare any coffee specialities, but you can prepare hot water or milk.

The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any coffee specialities or hot water or milk products.

The IMPRESSA is prompting you to rinse it.

The bean container is empty. You cannot prepare any coffee specialities, but you can prepare hot water or milk.

The IMPRESSA is prompting you to start cappuccino rinsing.

READY / CLEAN After 200 preparations or 80

switch-on rinses, the IMPRESSA will prompt you to clean it.

READY / DE-SCALE The IMPRESSA is prompting

you to descale it.

READY / FILTER After 2 months or when 50 lit-

res of water have flowed through the filter, its capacity is reached.

T Fill the water tank (See Chapter 2, ‘Preparing and using for the first time – Filling the water tank’)

T Empty the coffee grounds container and the drip tray.

T Insert the drip tray.

T Press the maintenance button to start rinsing.

T Fill the bean container (See Chapter 2, ‘Preparing and using for the first time – Filling the bean container’)

T Press the maintenance button to start cappuccino rinsing.

T Clean the machine (See Chapter 6, ‘Maintenance – Cleaning the machine’)

T Descale the machine (See Chapter 6, ‘Maintenance – Descaling the machine’)

T Replace the CLARIS filter cartridge (See Chapter 6 ‘Maintenance – Changing the filter’).

7 Display messages

Message Cause/Result Action

NOT ENOUGH

PRE-GROUND

TOO HOT

There is too little pre-ground coffee in the filler funnel. The IMPRESSA stops the operation.

The system is too hot to start a maintenance programme.

T The next time you make coffee use more pre-ground coffee (refer to Chapter 4, ‘Preparation at the touch of a button – Pre-ground coffee’).

T Prepare a coffee speciality or hot water.

8 Troubleshooting

Problem Cause/Result Action

Grinder is making a very loud noise.

Insufficient foam is produced when the milk is foamed or milk sprays from the cappuccino frother.

Coffee only comes out in drips when it is being prepared.

Water hardness cannot be adjusted.

FILL BEANS is displayed

although the bean container has been filled.

FILL WATER TANK is

displayed although the water tank is full.

ERROR 2 is displayed. If the device was exposed to

Other

ERROR messages

are displayed.

There are some foreign bodies in the grinder.

The cappuccino frother is dirty.

Coffee or pre-ground coffee has been ground too finely and is blocking the system.

The CLARIS filter cartridge is activated.

The grinder is not yet completely filled with beans.

The water tank float is trapped.

the cold for a long period of time, it is disabled from heating up due to safety reasons.

– T Turn the IMPRESSA off at the

T Contact customer support in your country (see ‘JURA contact details / Legal information’).

T Rinse and clean the cappuccino frother (see Chapter 6, ‘Maintenance – Cappuccino frother’).

T Put the grinder on a coarser setting or use coarser pre-ground coffee (refer to Chapter 2, ‘Preparing and using for the first time – Adjusting grinder’).

T Deactivate the CLARIS filter cartridge.

T Prepare a coffee speciality.

T Descale the water tank (see Chapter 6, ‘Maintenance – Descaling the water tank’).

T Warm up the device at room temperature.

power switch. Contact customer support in your country (see ‘JURA contact details / Legal information’).

8 Troubleshooting

E If you have not been able to solve the problem, contact cus-

tomer support in your country (see ‘JURA contact details / Legal information’).

9 Transport and environmentally neutral disposal

Transport / Empty system

Keep the packaging for your IMPRES SA. It should be used to protect the machine during transportation.

In order to protect the IMPRESSA from frost during transportation, the system must be emptied.

Precondition:

ü T Press the milk foam button.

READY is displayed.

T Carefully pull the frother off the Connector System T Place a container under the Connector System

HEATING

READY appears as soon as the IMPRESSA has heated up.

ü T Press the milk foam button once more.

MILK, steam is discharged from the Connector System

g T Turn the Rotary Switch until

T Remove the water tank and empty it.

Steam is discharged until

Q T Press the On/Off button to switch the machine off. 3 T Turn your IMPRESSA off at the power switch.

E The next time you use the machine the system must be

refilled (see Chapter 2, ‘Preparing and using for the first time – First-time use’).

40 SEC is displayed.

FILL WATER TANK appears.

Disposal

Please dispose of old machines in an environmentally neutral way.

Old machines contain valuable materials capable of being recycled which should be salvaged for recycling. Please therefore dispose of old machines via suitable collection systems.

10 Technical data

Voltage

Power 1450 W Safety test Power consumption

in standby mode Power consumption

A S F D G

S F D G

3,7 Wh

18 Wh

230 V AC, 50 Hz 120 V AC, 60 Hz 220 – 240 V AC, 50 Hz 220 V AC, 50 Hz

ENERGY SAVE -

Power consumption

11 Wh

ENERGY SAVE w.

Pump pressure Static max. 15 bar Holding capacity of water tank 1,9 l Holding capacity

of bean container Holding capacity of coffee

grounds container Cable length Approx. 1,1 m Weight 9,6 kg Dimensions (W x H x D) 28 x 34,5 x 43,4 cm

200 g

Approx. 16 servings

Index

Index A

Adresses 64 Amount

Adjusting the default amount of water to suit the cup size 24 Changing the amount of water during preparation 24

Amount of coffee

Adjusting the default amount of water to suit the cup size 24 Changing the amount of water during preparation 24

Amount of water

Adjusting the default amount of water to suit the cup size 24 Changing during preparation 24

Aroma preservation cover 8 Automatic switch-off 39

Bean container 8

Aroma preservation cover 8 Cleaning 53 Cover 8 Filling 15

Bus bar

Technical data 59

Cappuccino 30

With the Easy Cappuccino Frother 30 With the Professional Cappuccino Frother 31

Cappuccino Frother

Easy Cappuccino Frother 9 Professional Cappuccino Frother 9

CLARIS filter cartridge

Changing 43 Using and activating filter 17

Cleaning

Bean container 53 Easy Cappuccino Frother 49 Machine 44 Professional Cappuccino Frother 51

Coffee 30 Coffee grounds container 8 Coffee spout, height-adjustable 8

Coffee strength

Changing the coffee strength before preparation 24

Bean container 8 Filler funnel for pre-ground coffee 8 Water tank 8

Customer support 64

Descaling

Machine 46 Water tank 54

Determining water hardness and adjusting 18 Display

Messages 55 Plain text 9

Display messages 55 Disposal 58 Drip tray 8

Easy Cappuccino Frother

Cleaning 49 Disassembling and rinsing 50 Rinsing 48

Emptying the system 58 Energy-saving mode 13, 37 Environmentally neutral disposal 58 Errors

Troubleshooting 57

Espresso 29

Filler funnel for pre-ground coffee 8 Filling

Bean container 15 Water tank 15

Filter

Changing 43 Using and activating filter 17

Fineness of grind

Adjusting the grinder 19 Fineness of grind switch 8

Fineness of grind switch 8 First-time use 16

Index

Frother

Easy Cappuccino Frother 9, 14 Professional Cappuccino Frother 9, 14

Hardness of water 18 Height-adjustable coffee spout 8 Hotline 64 Hot milk

Foaming and heating milk with the Professional Cappuccino Frother 33

Hot water 34 Hot water nozzle 9

Inserting

water tank 15

Instant coffee

Pre-ground coffee 32

Internet 14

JURA contact details 64

Knowledge Builder 14

Language 40 Legal information 64

Machine

Cleaning 44 Descaling 46 Rinsing 42 Setting up 15 Switching off (standby) 20 Switching on 20

Maintenance

Maintenance button 9 Maintenance tips 42

Maintenance status, Query 27 Malfunction

Troubleshooting 57

Milk

Foaming and heating with the Professional Cappuccino Frother 33 Foaming with the Easy Cappuccino Frother 33

Milk foam

With the Easy Cappuccino Frother 33 With the Professional Cappuccino Frother 33

One-off settings before and during prepara-

tion 23

Permanent settings in programming mode

35 Plain text display 9 Power switch 8 Pre-ground coffee 32

Filler funnel 8

Preparation

At the touch of a button 29 Cappuccino 30 Coffee 30 Espresso 29 Hot water 34 Pre-ground coffee 32

Problems

Troubleshooting 57

Professional Cappuccino Frother 14

Cleaning 51 Disassembling and rinsing 53 Rinsing 50

Programmable switch-on time 38 Programming mode 35

Automatic switch-off 39 Energy-saving mode 37 Language 40 Products 35 Programmable switch-on time 38 Time 38 Unit amount of water/Time format 40

Prompt to take action

Symbols used 12

Query information and maintenance status

27 Query maintenance status 27

Reinsert

Water tank 15

Index

Rinse

Maintenance button 9

Rinsing

Easy Cappuccino Frother 48 Machine 42 Professional Cappuccino Frother 50

Rotary Switch 9

Safety information 10 Settings

Adjusting the default amount of water to suit the cup size 24 One-off settings before and during preparation 23 Permanent settings in programming mode 35

Set up 15 Standby

Switching off 20

Switching off (standby) 20 Switching on 20

Technical data 59 Time 38 Time format 40 Transport 58 Troubleshooting 57

Use, First-time 16

Voltage 59

Water hardness 18 Water tank 8

Descaling 54 Filling 15

Works settings 37

Art. 67606/C9/en/201003

JURA contact details / Legal information

JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Phone: +41 62 38 98 233

@ Contact information is available on the company website at

www.jura.com.

Directives

Technical changes

Feedback

The machine complies with the following EU directives:

Z 2006/95/EC – Low Voltage Directive Z 2004/108/EC – Electromagnetic Compatibility

We reserve the right to make technical changes.

The illustrations used in the IMPRESSA C9 Manual show the IMPRESSA C9 Piano Black. Your IMPRESSA could incorporate minor changes.

Your opinion is important to us! Use the contact link at www.jura.com.

The Instructions for Use contain information which is protected by copyright. It is not permitted to photocopy or translate these Instructions for Use into another language without the express written consent of JURA Elektroapparate AG.

JURA C9 Operating Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual