JURA 15292 User Manual

Download

ENA 8 Instructions for Use

Table of contents

Your ENA 8

Control elements 36

Important information 38

Proper use ...............................................................................................................................................................38

For your safety .......................................................................................................................................................38

1 Preparing and using for the first time 40

JURA on the Internet ............................................................................................................................................ 40

Setting up the machine ....................................................................................................................................... 40

Filling the bean container ...................................................................................................................................40

Determining the water hardness ........................................................................................................................ 41

First-time use .......................................................................................................................................................... 41

Connecting milk .....................................................................................................................................................42

Connecting an accessory (via Bluetooth) ..........................................................................................................42

2 Preparation 43

Espresso, coffee and other speciality coffees ...................................................................................................43

Latte macchiato, cappuccino and other speciality coffees with milk ...........................................................43

Ground coffee ........................................................................................................................................................ 44

Adjusting the grinder ........................................................................................................................................... 45

Hot water................................................................................................................................................................ 45

3 Daily operation 45

Filling the water tank ........................................................................................................................................... 45

Switching on the machine .................................................................................................................................. 46

Daily maintenance ................................................................................................................................................ 46

Regular maintenance ........................................................................................................................................... 46

Switching off the machine .................................................................................................................................. 46

4 Permanent settings in programming mode 47

Adjusting the product settings .......................................................................................................................... 48

Automatic switch-off ............................................................................................................................................ 48

Energy-saving mode ............................................................................................................................................ 49

Restore factory settings ....................................................................................................................................... 49

Unit for amount of water .................................................................................................................................... 49

Setting the water hardness ................................................................................................................................. 49

Language ................................................................................................................................................................ 50

5 Maintenance 50

Rinsing the machine ............................................................................................................................................ 50

Automatic milk system rinsing ........................................................................................................................... 51

Cleaning the milk system ..................................................................................................................................... 51

Dismantling and rinsing the dual spout ............................................................................................................52

Inserting/changing the filter ................................................................................................................................53

Cleaning the machine .......................................................................................................................................... 54

Descaling the machine ....................................................................................................................................... 54

Descaling the water tank ..................................................................................................................................... 56

Cleaning the bean container .............................................................................................................................. 56

Table of contents

6 Display messages 57

7 Troubleshooting 58

8 Transport and environmentally friendly disposal 59

Transport/ Emptying the system ...................................................................................................................... 59

Disposal .................................................................................................................................................................. 59

9 Technical data 59

10 Index 60

11 JURA contact details/ Legal information 62

Symbol description

Warnings

J WARNING

J CAUTION

CAUTION CAUTION draws your attention to potential damage to the machine.

Symbols used

‘Coffee’ Display

Always take note of any information marked with the words CAUTION or WARNING and a warning sign. The signal word WARNING draws your attention to potential serious injury, and the signal word CAUTION to potential minor injury.

Prompt to take action. This symbol means that you are being prompted to perform some action.

Information and tips to make it even easier to use your ENA.

Control elements

1 Display 2 Mains cable (back of the machine) 3 Height-adjustable dual spout 4 Coffee grounds container 5 Drip tray 6 Cup grille

7 Water tank (with cover) 8 Multi-function buttons (button function

depends on what is shown in the display) 9 Hot-water spout 10 Insert for drip tray

Control elements

1 Bean container with aroma preservation cover 2 Powder chute for ground coffee

Back of the machine: Service socket for JURA Smart Connect (behind cover) . Smart Connect is not included with all models.

3 On/Off button Q 4 Grinding wheel

Accessories

Filler funnel for ground coffee Measuring spoon for ground

coffee

Container for milk system cleaning

Important information

Proper use

The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use.

Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain. A warranty service is not applicable for damage or defects caused by non-compliance with the instructions for use. Keep these instructions for use close to the machine and pass them on to the next user.

For your safety

Please carefully read and observe the important safety information set out below. To avoid danger of potentially fatal electric shock:

Never use a machine which is

damaged or has a defective mains cable.

In the event of signs of damage,

for example if there is a smell of burning, unplug the machine immediately from the mains supply and contact JURA service. If the mains cable of this

machine is damaged, it must be repaired either directly by JURA or by an authorised JURA service centre. Make sure that the ENA and the

mains cable are not located close to hot surfaces. Be careful to ensure that the

mains cable is not trapped and does not rub against sharp edges. Never open and repair the

machine yourself. Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories. To completely and safely discon-

nect the machine from the power supply, first switch off the ENA using the On/Off button Q. Only then should you remove the mains plug from the power socket.

Important information

There is a risk of scalds or burns on the spouts.

Place the machine out of the

reach of children. Do not touch any hot parts.

Use the handles provided. Be careful to ensure that the dual

spout is correctly installed and clean. If it is incorrectly fitted or becomes blocked, its parts might come off. There is a danger of parts being swallowed.

A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire:

Never allow the mains cable to

loosely hang down. The mains cable could pose a tripping hazard or become damaged. Protect the ENA from environ-

mental influences such as rain, frost and direct sunlight. Do not immerse the ENA, mains

cable or connections in water. Do not put the ENA or any

individual parts in the dishwasher. Do not use alkaline cleaning

agents; only use a soft cloth and mild cleaning agents. Switch your ENA off at the power

switch before any cleaning operation. Always wipe the ENA

with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash. Only connect the machine to

the mains voltage in accordance with the information on the rating plate. The rating plate is located on the underside of your ENA. Further technical data is provided in these instructions for use (see Chapter 9 ‘Technical data’). Please only use original JURA

maintenance products. Use of products that are not explicitly recommended by JURA could damage the machine. Do not use any coffee beans

treated with additives or caramelised coffee beans. Only fill the water tank with

fresh, cold water. Switch the machine off with the

On/Off button Q if you are going to be absent for a longer period of time and remove the mains plug from the power socket. Children may not clean or ser-

vice the machine unless supervised by a responsible person. Do not allow children to play

with the machine.

1 Preparing and using for the first time

Keep children under the age of 8

away from the machine, or supervise them constantly. Children aged 8 and over may

only operate the machine without supervision if they have been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.

People, including children, who

do not have the physical,

sensory or mental capabilities to use the machine safely or are inexperienced or lack knowl-

edge in how to use the machine

safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.

1 Preparing and using for the

first time

JURA on the Internet

Visit us on the Internet.

On the JURA website (www.jura.com) you will find interesting and up-to-date information on your ENA and on every aspect of coffee.

Setting up the machine

When setting up your ENA, please note the following:

Place the ENA on a horizontal surface that is

not sensitive to water. Choose a spot for your ENA which protects the

machine against overheating. Ensure that the ventilation slots are not covered.

Safety when handling the CLARIS Smart / Smart mini filter cartridge:

Filter cartridges should be kept

out of the reach of children.

Store filter cartridges in a dry

place in the sealed packaging.

Protect cartridges from heat and

direct sunlight.

Do not use damaged filter

cartridges.

Do not open filter cartridges.

Filling the bean container

The bean container has an aroma preservation cover. This will ensure that your coffee beans retain their aroma for longer.

CAUTION

Coffee beans which have been treated with additives (e.g. sugar), ground coffee or freeze-dried coffee will damage the grinder.

T Only use roasted, untreated coffee beans to

fill the bean container.

T Remove the aroma preservation cover. T Remove any dirt or foreign objects from

inside the bean container.

T Fill the bean container with coffee beans and

close the aroma preservation cover.

1 Preparing and using for the first time

Determining the water hardness

When you use the machine for the first time, you must set the water hardness. If you do not know the hardness of your water, you can find this out first. Use the Aquadur® test strips supplied with the machine.

T Hold the test strip briefly (for 1second)

under flowing water. Shake off the water.

T Wait for about 1minute.

T You will then be able to read the degree of

water hardness from the discolouration of the Aquadur® test strip and the description on the packaging.

First-time use

J WARNING

If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock.

T Never use a machine which is damaged or

has a defective mains cable.

CAUTION

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

E To display more languages, press the ‘`’

button.

T Press the button that corresponds to the

language you want, e.g.

‘Saved’ appears briefly on the display to

confirm the setting.

‘Water hardness’

E If you do not know the hardness of your

water, you must find this out first (see Chapter 1 ‘Preparing and using for the first time – Determining the water hardness’).

T Press the

setting for the water hardness.

T Press the

‘Saved’ appears briefly on the display. ‘Filter operation’ / ‘Insert filter’

T Place a receptacle under the dual spout and

the hot-water spout.

T Remove the water tank and rinse it with cold

water.

T Fit the filter cartridge extension supplied on

top of the CLARIS Smart mini filter cartridge.

‘<’ or ‘>’ button to change the

‘Save’ button.

‘English’.

Precondition:The bean container has been filled.

T Insert the mains plug into a power socket.

T Press the On/Off button Q to switch the ENA

on.

‘Choose language’

1 Preparing and using for the first time

T Insert the filter cartridge with its extension

into the water tank.

click! click!

T Fill the water tank with fresh, cold water and

reinsert the tank.

E The machine automatically detects that you

have just inserted the filter cartridge.

‘Saved’ ‘Filter is being rinsed’

Water flows directly into the drip tray.

‘Empty drip tray’ message appears,

E If the

empty the drip tray and put it back into the machine.

‘System is filling’ ‘Machine is heating’ ‘Machine is rinsing’

The rinse stops automatically. The start screen is displayed. Your ENA is ready for use.

E If the filter is active, this is indicated by a

blue filter symbol at the bottom of the display.

Connecting milk

Your ENA creates fine, creamy, feather-light milk foam with a perfect consistency. The most important requirement for frothing milk is a milk temperature of 4–8°C. We would therefore recommend using a milk cooler or a milk container.

, the filter is rinsed.

T Remove the protective cover from the dual

spout.

T Connect the milk pipe to the dual spout.

T Connect the other end of the milk pipe to a

milk container or a milk cooler.

Connecting an accessory (via Bluetooth)

You have the option of connecting your ENA wirelessly to a compatible accessory (e.g. the Cool Control Wireless milk cooler). To do this, the receiver of the Cool Control or the JURA Smart Connect must be plugged into the service socket.

E The Smart Connect can be protected

against unauthorised access using a PIN. Activate the PIN function via the JURA app. You will find more information at www.jura.com/smartconnect.

E Please note that you can only connect either

the Cool Control or only one JURA app to the coffee machine via Smart Connect.

Precondition:The start screen is displayed.

T Press the

2 seconds to enter programming mode.

T Press the

‘P’ button for approximately

‘`’ button.

2 Preparation

T Press the ‘Machine settings’ button.

T Press the

‘4/5’ is displayed.

T Press the

‘Connect accessory’

T Now follow the instructions on the display to

connect the accessory to the ENA.

‘`’ button several times until page

‘Connect accessory’ button.

2 Preparation

Basic information about preparing drinks:

During the grinding operation you can change

the coffee strength by pressing the

‘>’ buttons.

During preparation you can change the preset

amounts (e.g. water and amount of milk

foam) by pressing the

If you have selected settings during prepara-

tion, you can save these changes after

preparation. To do this, press the

button.

You can stop preparation at any time. To do

this, press the

Coffee tastes best served hot. A cold porcelain cup cools the beverage – and impairs the taste. We therefore recommend prewarming the cups. The full coffee aroma can develop only in prewarmed cups. You can purchase a JURA cup warmer from your specialised dealer.

You can make permanent settings for all products in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).

‘<’ and ‘>’ buttons.

‘Cancel’ button.

Espresso, coffee and other speciality coffees

Ristretto, espresso and coffee are all prepared following this model.

Two brewing operations are carried out for the espresso doppio to create a particularly full-bodied and aromatic speciality coffee.

‘<’ and

‘Save’

Example:Proceed as follows to prepare one coffee. Precondition:The start screen is displayed.

T Place a cup under the dual spout.

T Press the

Preparation starts. strength are displayed. The preset amount of water for coffee flows into the cup. Preparation stops automatically. Your ENA is once more ready for use.

‘Coffee’ button.

‘Coffee’ and the coffee

Latte macchiato, cappuccino and other speciality coffees with milk

Your ENA prepares latte macchiato, cappuccino and other speciality coffees with milk at the touch of a button. There is no need to move the glass or cup.

Example:Proceed as follows to prepare one latte macchiato. Precondition:The start screen is displayed. Milk is connected to the dual spout.

T Place a glass under the dual spout.

T Press the

times needed to display page

‘_’ or ‘`’ button the number of

‘2/5’.

2 Preparation

T Press the ‘Latte macchiato’ button.

‘Latte macchiato’, the preset amount of milk

foam flows into the glass.

E There is a short interval while the hot milk

separates from the milk foam. This allows the typical layers of a latte macchiato to form.

Coffee preparation starts. The preset amount of water for espresso flows into the glass. Preparation stops automatically. Your ENA is once more ready for use.

E 15 minutes after preparation, the milk

system is automatically rinsed (see Chapter 5 ‘Maintenance – Automatic milk system rinsing’). Therefore always place a receptacle under the dual spout after preparing milk.

To ensure that the milk system in the dual spout always works properly, you must clean it daily (see Chapter 5 ‘Maintenance – Cleaning the milk system’).

Ground coffee

You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee.

Basic information about ground coffee:

Never add more than one level measuring

spoon of ground coffee.

Use ground coffee which is not ground too

finely. Very fine coffee can block up the system

so that the coffee only comes out in drips.

If you did not fill the machine with a sufficient

amount of ground coffee,

coffee’

is displayed and the ENA stops the operation. The desired speciality coffee must be prepared

within approximately one minute after filling with the ground coffee. Otherwise the ENA stops the operation and is once more ready for use.

‘Not enough ground

All speciality coffees with ground coffee are always prepared following the same model.

Example:Proceed as follows to prepare one espresso using ground coffee. Precondition:The start screen is displayed.

T Place an espresso cup under the coffee

spout.

T Open the powder chute for ground coffee.

‘Ground coffee’ / ‘Please add ground coffee’

T Fit the filler funnel for ground coffee.

T Place one level measuring spoon of ground

coffee into the filler funnel.

T Remove the filler funnel and close the cover

of the powder chute.

T Press the

Preparation starts. amount of water for espresso flows into the cup. Preparation stops automatically. Your ENA is once more ready for use.

‘Espresso’ button.

‘Espresso’, the preset

3 Daily operation

Adjusting the grinder

You can adjust the grinder to suit the degree of roast of your coffee.

CAUTION

If you adjust the consistency of grind when the grinder is not operating, the grinding wheel could be damaged.

T Only adjust the consistency of grind when

the grinder is running.

The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.

Grinding wheel (see image)

1: Coarse consistency of grind setting

2: Fine consistency of grind setting

Example:Proceed as follows to change the

consistency of grind during the preparation of an espresso.

T Place a cup under the dual spout. T Press the T Turn the grinder adjustment wheel to the

desired position while the grinder is running. The preset amount of water flows into the cup. Preparation stops automatically. Your ENA is once more ready for use.

‘Espresso’ button.

Hot water

 CAUTION

There is a danger of scalding from hot water splashes.

T Avoid direct contact with the skin.

Precondition:The start screen is displayed.

T Place a cup under the hot-water spout.

T Press the

times needed to display page

T Press the

‘Hot water’, the preset amount of water

flows into the cup. Preparation stops automatically. Your ENA is once more ready for use.

‘`’ or ‘_’ button the number of

‘5/5’.

‘Hot water’ button.

3 Daily operation

Filling the water tank

Daily maintenance of the machine and hygiene when handling milk, coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily.

CAUTION

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Remove the water tank and rinse it with cold

water.

T Fill the water tank with fresh, cold water and

reinsert the tank.

3 Daily operation

Switching on the machine

T Place a receptacle under the dual spout.

T Press the On/Off button Q to switch the ENA

on.

‘Welcome to JURA’ ‘Machine is heating’ ‘Machine is rinsing’

The rinse stops automatically. Your ENA is ready for use.

Daily maintenance

To ensure that you get many years of reliable service out of your ENA and to guarantee the optimum coffee quality, the machine requires daily maintenance.

T Pull out the drip tray.

T Clean the milk system in the dual spout

(see Chapter 5 ‘Maintenance – Cleaning the milk system’).

T Remove the milk pipe and rinse it

thoroughly under running water.

T Dismantle and rinse the dual spout

(see Chapter 5 ‘Maintenance – Dismantling and rinsing the dual spout’).

T Wipe the surface of the machine with a

clean, soft, damp cloth (e.g. microfibre cloth).

Regular maintenance

Carry out the following maintenance actions regularly or as required:

In the interests of hygiene, we recommend

changing the milk pipe and interchangeable milk spout on a regular basis (approximately every 3 months). Replacements are available from specialised dealers. Your ENA is equipped with the HP1 milk system. Clean the inside of the water tank, e.g. with a

brush. Further information about the water tank is provided in these instructions for use (see Chapter 5 ‘Maintenance – Descaling the water tank’). Traces of milk and coffee may stick to the top

and bottom of the cup grille. If this happens, clean the cup grille.

T Empty the coffee grounds container and the

drip tray. Rinse them both with warm water.

E Always empty the coffee grounds container

when the machine is switched on. This is the only way of resetting the coffee grounds counter.

T Refit the coffee grounds container and the

drip tray.

T Rinse the water tank with clean water.

Switching off the machine

When the ENA is switched off, the system is automatically rinsed if a speciality coffee has been prepared. If milk has been prepared, you will also be prompted to clean the milk system.

T Place a receptacle under the dual spout.

T Press the On/Off button Q.

E If milk has been prepared, you will be

prompted to clean the milk system (

want to clean the milk system now?’

10seconds the switch-off process continues automatically.

‘Machine is rinsing’, the system rinses itself.

The operation stops automatically. Your ENA is switched off.

‘Do you

). After

4 Permanent settings in pro-

gramming mode

Press the ‘P’ button for approximately 2seconds to enter programming mode. You can easily navigate through the programme items and permanently save the required settings using the multi-function buttons. The following settings can be made:

4 Permanent settings in programming mode

Programme item

‘Maintenance status’

‘Product settings’

‘Machine settings’

Sub-item Explanation

‘Clean’, ‘Clean the milk system’, ‘Descale’, ‘Filter’ (only if filter is fitted), ‘Rinse’, ‘Maintenance information’

‘Switch off after’

‘Save energy’

‘Factory setting’

‘Units’

‘Water hardness’

‘Choose language’

‘Connect accessory’, ‘Disconnect accessories’

(Only displayed if the JURA Smart Connect is being used.)

‘Version’ Software version

T Here you can start the required maintenance programme or find out what maintenance actions are required.

T Select your settings for speciality coffees and hot water.

T Set the time after which the ENA should switch off automatically.

T Activate energy-saving mode. TReset the machine to its factory setting. T Select the unit for the amount of water. T You can set the water hardness of the water used. T Select your language. T Connect the ENA wirelessly to a JURA accessory or

disconnect the connection again.

4 Permanent settings in programming mode

Adjusting the product settings

Press the button of a product on the start screen for about 2 seconds to view the list of setting options. The following permanent settings can be made:

Product Coffee strength Amount More settings

Ristretto, Espresso

Coffee 10 levels Coffee: 25ml–240ml Temperature (low,

Cappuccino, Flat white

Latte macchiato 10 levels Coffee: 25ml–240ml

Espresso macchiato 10 levels Coffee: 15ml–80ml

Espresso doppio (2 brewing operations)

Portion of milk foam – Milk foam: 3sec.–120sec. – Hot water – Water: 25ml–450ml Temperature (low,

10 levels Coffee: 15ml–80ml Temperature (low,

normal, high)

10 levels Coffee: 25ml–240ml

Milk foam: 3sec.–120sec.

Milk foam: 3sec.–120sec. Interval: 0sec.–60sec.

Milk foam: 3sec.–120sec.

10 levels Coffee: 30ml–160ml Temperature (low,

Temperature (low, normal, high)

normal, high)

Permanent settings in programming mode always follow the same model.

Example:Proceed as follows to change the coffee strength for one coffee. Precondition:The start screen is displayed.

T Press the

2 seconds until the list of possible settings appears.

‘Coffee’

T Press the ‘Coffee strength’ button.

‘Coffee strength’

T Press the ‘<’ or ‘>’ button to change the

setting for the coffee strength.

T Press the

‘Saved’ appears briefly on the display. ‘Coffee’

T Press the ‘Back’ button to return to the start

screen.

‘Coffee’ button for approximately

‘Save’ button.

Automatic switch-off

By instructing your ENA to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your ENA switches off automatically after the preset time following the last action on the machine.

You can set the automatic switch-off to 15minutes, 30minutes or 1-9hours.

Precondition:The start screen is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the T Press the

‘Switch off after’

T Press the ‘<’ or ‘>’ button to change the

setting.

‘P’ button for approximately

‘`’ button. ‘Machine settings’ button. ‘Switch off after’ button.

4 Permanent settings in programming mode

T Press the ‘Save’ button.

‘Saved’ appears briefly on the display. ‘Machine settings’

T Press the ‘Back’ button for approximately

2 seconds to return to the start screen.

Energy-saving mode

In the programme item ‘Machine settings’ / ‘Save

energy’

you can set an energy-saving mode:

‘Save energy’ / ‘Ac tive’

Soon after the last preparation, the ENA

stops heating up. Before you can prepare a speciality coffee,

speciality coffee with milk, or hot water, the machine must heat up.

‘Save energy’ / ‘Inactive’

All speciality coffees, speciality coffees with

milk and hot water can be prepared without having to wait.

Example:Proceed as follows to deactivate the energy-saving mode. Precondition:The start screen is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the T Press the

‘Save energy’

T Press the ‘Inactive’ button. T Press the

‘Saved’ appears briefly on the display. ‘Machine settings’

T Press the ‘Back’ button for approximately

2 seconds to return to the start screen.

‘P’ button for approximately

‘`’ button. ‘Machine settings’ button. ‘Save energy’ button.

‘Save’ button.

Restore factory settings

In the programme item ‘Machine settings’ /

‘Factory setting’ the machine can be reset to its

factory setting.

Precondition:The start screen is displayed.

T Press the

2 seconds to enter programming mode.

‘P’ button for approximately

T Press the T Press the T Press the

‘2/5’

T Press the ‘Factory setting’ button.

‘Factory setting’ / ‘Reset the machine to the factory settings?’

T Press the ‘Yes’ button.

‘Saved’ appears briefly on the display.

Your ENA is switched off.

‘`’ button. ‘Machine settings’ button. ‘`’ button.

Unit for amount of water

In the programme item ‘Machine settings’/ ‘Units’ you can select the unit used for the amount of water.

Example:Proceed as follows to change the unit for the amount of water from Precondition:The start screen is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the T Press the

‘2/5’

T Press the ‘Units’ button.

‘Units’

T Press the ‘oz’ button. T Press the

‘Saved’ appears briefly on the display. ‘Machine settings’

T Press the ‘Back’ button for approximately

2 seconds to return to the start screen.

‘P’ button for approximately

‘`’ button. ‘Machine settings’ button. ‘`’ button.

‘Save’ button.

‘ml’ to ‘oz’.

Setting the water hardness

The harder the water is, the more frequently the ENA needs to be descaled. It is therefore important to set the water hardness accurately.

The water hardness was set when the machine was first used. You can change this setting at any time.

The water hardness can be adjusted on a continuous scale between 1 °dH and 30 °dH.

5 Maintenance

Precondition:The start screen is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the T Press the

‘3/5’ is displayed.

T Press the

‘Water hardness’

T Press the ‘<’ or ‘>’ button to change the

setting.

T Press the

‘Saved’ appears briefly on the display. ‘Machine settings’

T Press the ‘Back’ button for approximately

2 seconds to return to the start screen.

‘P’ button for approximately

‘`’ button. ‘Machine settings’ button. ‘`’ button several times until page

‘Water hardness’ button.

‘Save’ button.

Language

In this programme item you can set the language used by your ENA.

Example:Proceed as follows to change the language from Precondition:The start screen is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the T Press the

‘3/5’ is displayed.

T Press the

‘Choose language’

T Press the ‘Deutsch’ button.

‘Gespeichert’ appears briefly on the display. ‘Geräteeinstellungen’

T Press the ‘Zurück’ button for approximately

2 seconds to return to the start screen.

‘English’ to ‘Deutsch’.

‘P’ button for approximately

‘`’ button. ‘Machine settings’ button. ‘`’ button several times until page

‘Choose language’ button.

5 Maintenance

Your ENA has the following integrated maintenance programmes:

Rinsing the machine (‘Rinse’)

Cleaning the milk system (‘Clean the milk

system’

)

Changing the filter (only if filter is fitted)

Cleaning the machine (‘Clean’)

Descaling the machine (‘Descale’)

E Clean the machine, descale the machine or

change the filter when you are prompted to do so.

E In the programme item

you will find an overview of the maintenance programmes. When the bar is completely filled with red, your ENA will prompt you to perform the appropriate maintenance programme.

E In the interests of hygiene, you should clean

the milk system daily when you have been preparing milk.

Rinsing the machine

You can initiate the rinse operation manually at any time.

Precondition:The start screen is displayed.

T Place a receptacle under the dual spout.

‘Maintenance status’

T Press the

2 seconds to enter programming mode.

T Press the T Press the

‘3/3’ is displayed.

‘P’ button for approximately

‘Maintenance status’ button. ‘`’ button several times until page

5 Maintenance

T Press the ‘Rinse’ button.

‘Machine is rinsing’, ‘Milk system is being rinsed’

, water flows out of the dual spout. The rinse stops automatically. Your ENA is once more ready for use.

Automatic milk system rinsing

15 minutes after milk preparation, the milk system

is automatically rinsed. Therefore always place a receptacle under the dual spout after preparing milk.

Cleaning the milk system

To ensure that the milk system in the dual spout always works properly, you must clean it daily when you have been preparing milk.

CAUTION

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance

products.

E JURA milk system cleaner is available from

specialised dealers.

E To clean the milk system, use the container

supplied.

Precondition:The ‘Cleaning the milk system’ (6) symbol is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the

‘Clean the milk system’

T Press the ‘Start’ button. T Press the

‘Milk system cleaner’

T Remove the milk pipe from the milk

container or milk cooler.

‘P’ button for approximately

‘Maintenance status’ button. ‘Clean the milk system’ button.

‘Next’ button.

T Add milk system cleaner to the front part of

the container up to the bottom mark (indicated by 6).

T Then fill with water up to the upper mark. T Place the container under the dual spout. T Connect the milk pipe to the container.

E To connect the milk pipe to the container

correctly, the pipe must be fitted with a connector.

T Press the

‘Milk system is being cleaned’, the dual

spout and the milk pipe are cleaned.

‘Fresh water’

T Rinse the container thoroughly and fill the

front part with fresh water up to the upper

mark.

T Place it under the dual spout and reconnect

the milk pipe with the container.

T Press the

‘Milk system is being cleaned’, the dual

spout and the pipe are rinsed with fresh water. The operation stops automatically. Your ENA is once more ready for use.

‘Next’ button.

5 Maintenance

Dismantling and rinsing the dual spout

The dual spout must be dismantled and rinsed daily if milk has been prepared to make sure it functions perfectly and also in the interests of hygiene.

T Remove the milk pipe and rinse it thor-

oughly under running water.

T Pull the cover of the dual spout forwards

and off.

T Dismantle the milk system into its individual

parts.

T Rinse all the parts under running water.

If there are severely dried-on milk residues, firstly immerse the individual parts in a solution of 250ml cold water and 1 capful of JURA milk system cleaner. Then rinse the parts thoroughly.

T Fit the air intake pipe.

T Remove the milk system from the dual

spout.

T Reassemble the milk system. When doing

this, note the numbering of the individual parts.

5 Maintenance

T Fit the assembled individual parts back in

the dual spout and press it firmly.

T Refit the cover of the dual spout.

Inserting/changing the filter

Your ENA no longer has to be descaled if you are using the CLARIS Smart / Smart mini filter cartridge.

T Remove the used filter cartridge from the

water tank.

T Fit the filter cartridge extension on top of a

new CLARIS Smart / Smart minifilter cartridge.

T Insert the filter cartridge with its extension

into the water tank.

E Once the filter cartridge stops working

(depending on the water hardness setting), the ENA will prompt you to change the filter.

E CLARIS Smart / Smart mini filter cartridges

are available from specialised dealers.

Precondition:The start screen is displayed. (If the filter needs to be changed, the $ symbol is also displayed.)

T Remove and empty the water tank.

click! click!

T Fill the water tank with fresh, cold water and

reinsert the tank. The machine has automatically detected that you have just inserted/changed the filter cartridge.

‘Filter is being rinsed’, the filter is rinsed.

Water flows directly into the drip tray. The start screen is displayed. Your ENA is once more ready for use.

5 Maintenance

Cleaning the machine

After 160preparations or 80switch-on rinses, the ENA will prompt you to clean it.

CAUTION

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance

products.

E The cleaning programme lasts approxi-

mately 20 minutes.

E Do not interrupt the cleaning programme.

The quality of cleaning will be impaired if you do so.

E JURA cleaning tablets are available from

specialised dealers.

Precondition:The ‘Cleaning the machine’ (7) symbol is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the

‘Clean’

T Press the ‘Start’ button. T Press the

‘Empty coffee grounds container’

T Empty the drip tray and coffee grounds

container and put them back into the machine.

‘Clean’

T Place a receptacle under the dual spout.

‘P’ button for approximately

‘Maintenance status’ button. ‘Clean’ button.

‘Next’ button.

T Press the ‘Next’ button.

‘Machine is being cleaned’, water flows out

of the dual spout. The operation is interrupted,

tablet’

T Open the powder chute for ground coffee. T Insert a JURA cleaning tablet into the powder

chute.

T Close the powder chute.

‘Clean’

T Press the ‘Next’ button.

‘Machine is being cleaned’, water flows out

of the dual spout repeatedly. The operation stops automatically.

‘Empty coffee grounds container’

T Empty the drip tray and coffee grounds

container and put them back into the machine. Your ENA is once more ready for use.

‘Add cleaning

Descaling the machine

The ENA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.

E If you are using a CLARIS Smart / Smart mini

filter cartridge, you will not be prompted to descale.

5 Maintenance

J CAUTION

If the descaling agent comes into contact with the skin or eyes, this can cause irritation.

T Avoid contact with the skin or eyes. T Rinse off the descaling agent with clean

water. Should you get any descaling agent in your eye, see a doctor.

CAUTION

If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance

products.

CAUTION

If the descaling operation is interrupted, there may be damage to the machine.

T Allow the descaling programme to run to

the end.

CAUTION

If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out.

T Clean up any splashes immediately.

T Empty the drip tray and coffee grounds

container and put them back into the machine.

‘Agent in tank’

T Remove and empty the water tank. T Completely dissolve 3JURA descaling tablets

in a receptacle holding 500ml of water. This may take several minutes.

T Pour the solution into the empty water tank

and insert it into the machine.

T Place a receptacle under the hot-water

spout.

E The descaling programme lasts approxi-

mately 40minutes.

E JURA descaling tablets are available from

specialised dealers.

Precondition:The ‘Descaling the machine’ (%) symbol is displayed.

T Press the

2 seconds to enter programming mode.

T Press the T Press the

‘2/3’

T Press the ‘Descale’ button.

‘Descale’

T Press the ‘Start’ button. T Press the

‘Empty drip tray’

‘P’ button for approximately

‘Maintenance status’ button. ‘`’ button.

‘Next’ button.

T Press the

‘Machine is being descaled’, water flows

repeatedly out of the dual spout and the hot-water spout. The operation is interrupted,

tray’

T Empty the drip tray and coffee grounds

container and put them back into the machine.

‘Rinse the water tank’ / ‘Fill water tank’

T Empty the receptacle and place it under the

hot-water and dual spouts.

T Remove the water tank and rinse it

thoroughly.

‘Next’ button.

‘Empty drip

5 Maintenance

T Fill the water tank with fresh, cold water and

reinsert the tank.

T Press the

‘Machine is being descaled’, the descaling

operation is continued, water flows out of the dual spout and the hot-water spout.

‘Empty drip tray’

T Empty the drip tray and coffee grounds

container and put them back into the machine. Your ENA is once more ready for use.

E If the descaling operation stops unexpect-

edly, rinse the water tank thoroughly.

‘Next’ button.

Descaling the water tank

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time.

T Remove the water tank. T If you use a CLARIS Smart / Smart mini filter

cartridge, remove this.

T Completely fill the water tank and dissolve

3 JURA descaling tablets in it.

T Leave the water tank with the descaling solu-

tion for several hours (e.g. overnight).

T Empty the water tank and rinse it thor-

oughly.

T If you use a CLARIS Smart / Smart mini filter

cartridge, insert this again.

T Fill the water tank with fresh, cold water and

reinsert the tank.

Cleaning the bean container

Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time.

Precondition:

T Switch the machine off with the On/Off

T Remove the aroma preservation cover. T Clean the bean container with a soft, dry

T Fill the bean container with coffee beans and

‘Fill bean container’ is displayed.

button Q.

cloth.

close the aroma preservation cover.

6 Display messages

Message Cause/Result Action

‘Fill water tank’ The water tank is empty.

You cannot prepare any products.

‘Empty coffee grounds container’

‘Drip tray not fitted’ The drip tray is not inserted

‘Fill bean container’ The bean container is empty.

The ‘Changing the filter’ ($) symbol is displayed in red.

The ‘Cleaning the machine’ (7) symbol is displayed.

The ‘Descaling the machine’ (%) symbol is displayed.

The ‘Cleaning the milk system’ (6) symbol is displayed.

‘Too hot’ The system is too hot to start a

The coffee grounds container is full. You cannot prepare any products.

correctly or is not inserted at all. You cannot prepare any products.

You cannot prepare any speciality coffees, but you can prepare hot water and milk.

The filter cartridge no longer works.

The ENA is prompting you to clean it.

The ENA is prompting you to descale it.

The ENA prompts you to clean the milk system.

maintenance programme.

T Fill the water tank (see Chapter 3 ‘Daily operation – Filling the water tank’).

T Empty the coffee grounds container and the drip tray (see Chapter 3 ‘Daily operation – Daily maintenance’).

T Fit the drip tray.

T Fill the bean container (see Chapter 1

‘Preparing and using for the first time – Filling the bean container’).

T Replace the CLARIS Smart / Smart mini filter cartridge (see Chapter 5 ‘Maintenance – Inserting/changing the filter’).

T Perform cleaning (see Chapter 5 ‘Maintenance – Cleaning the machine’).

T Perform descaling (see Chapter 5 ‘Maintenance – Descaling the machine ’).

T Perform milk system cleaning (see Chapter 5 ‘Maintenance – Cleaning the milk system’).

T Wait for several minutes until the system has cooled or prepare a speciality coffee or hot water.

7 Troubleshooting

Problem Cause/Result Action

Insufficient foam is produced when the milk is frothed or milk sprays from the dual spout.

Coffee only comes out in drips when it is being prepared.

‘Fill water tank’ is not

displayed although the water tank is empty.

Grinder is making a very loud noise.

‘Error2’ or ‘Error5’ is

displayed.

Other

‘Error’ messages

are displayed.

The dual spout is dirty.

Coffee or ground coffee has been ground too finely and is blocking the system. The water hardness may not have been correctly set.

There is a lot of limescale in the water tank.

There are foreign objects in the grinder.

If the machine has been exposed to the cold for a long period of time, heating may be disabled for safety reasons.

–

T Clean the milk system in the dual spout (see Chapter 5 ‘Maintenance – Cleaning the milk system’). T Dismantle and rinse the dual spout (see Chapter 5 ‘Maintenance – Dismantling and rinsing the dual spout’).

T Put the grinder on a coarser setting or use coarser ground coffee (see Chapter 2 ‘Preparation – Adjusting the grinder’). T Perform descaling (see Chapter 5 ‘Maintenance – Descaling the machine’).

T Descale the water tank (see Chapter 5 ‘Maintenance – Descaling the water tank’).

T Contact customer support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

T Warm the machine at room temperature.

T Switch the ENA off with the On/Off

button Q. Contact customer support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

E If you were unable to solve the problem,

contact customer support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

8 Transport and environmentally friendly disposal

8 Transport and environmentally

friendly disposal

Transport/ Emptying the system

Keep the packaging for your ENA. It should be used to protect the machine during transport.

In order to protect the ENA from frost during transport, the system must be emptied.

Precondition:The start screen is displayed.

T Remove the milk pipe from the dual spout. T Place a receptacle under the hot-water

spout.

T Press the

times needed to display page

T Press the

‘Hot water’, hot water flows out of the

hot-water spout.

T Remove and empty the water tank.

Water will flow out of the hot-water spout until the system is empty.

‘Fill water tank’

T Press the On/Off button Q.

Your ENA is switched off.

Disposal

Please dispose of old machines in an environmentally neutral way.

Old machines contain valuable, recyclable materials which should be recycled. Please therefore dispose of old machines via suitable collection systems.

‘`’ or ‘_’ button the number of

‘5/5’.

‘Hot water’ button.

9 Technical data

Voltage 220–240V~, 50Hz Power 1450W Conformity mark

Pump pressure static, max. 15bar Holding capacity of

water tank (without filter)

Holding capacity of bean container

Holding capacity of coffee grounds container

Cable length approx. 1.2m Weight Art. 15241: approx. 10.9kg

Dimensions (WHD)

Milk system HP1

1.1l

125g

approx. 10 servings

Art. 15252/15240/15254: approx. 9.4kg

27.1  32.3  44.5cm

10 Index

Addresses 62 Adjusting the product settings 48 Aroma preservation cover

Bean container with aroma preservation cover 37

Automatic switch-off 48

Bean container

Bean container with aroma preservation cover 37 Cleaning 56

Filling 40 Bluetooth 42 Bus bar

Technical data 59 Button

On/Off button 37

Caffè latte 43 Cappuccino 43 Cappuccino frother cleaning

Cleaning the milk system 51 CLARIS Smart mini filter cartridge

Changing 53

Inserting 53 Cleaning

Bean container 56

Machine 54 Coffee 43 Coffee grounds container 36 Connecting an accessory 42 Consistency of grind

Adjusting the grinder 45

Grinding wheel 37, 45 Contact details 62 Cup grille 36 Customer support 62

Daily maintenance 46 Descaling

Machine 54

Water tank 56 Display 36 Display messages 57

Disposal 59 Drip tray 36

Insert 36

Dual spout

Dismantling and cleaning 52 Height-adjustable dual spout 36

Emptying the system 59 Energy-saving mode 49 Errors

Troubleshooting 58 Espresso 43 Espresso doppio 43

Factory settings

Restore factory settings 49 Filler funnel

Filler funnel for ground coffee 37 Filling

Bean container 40

Water tank 45 Filter

Changing 53

Inserting 53 First-time use 41 Flat white 43

Ground coffee 44

Measuring spoon for ground coffee 37

Powder chute for ground coffee 37

Homepage 40 Hotline 62 Hot water 45 Hot-water spout 36

Insert for drip tray 36 Instant coffee

Ground coffee 44 Internet 40

JURA

Contact details 62

Internet 40

10 Index

Language 50 Latte macchiato 43

Machine

Cleaning 54 Daily maintenance 46 Descaling 54 Regular maintenance 46 Rinsing 50 Setting up 40 Switching off 46

Switching on 46 Mains cable 36 Maintenance 50

Daily maintenance 46

Regular maintenance 46 Measuring spoon for ground coffee 37 Messages, display 57 Milk

Connecting milk 42 Milk system 59

Cleaning 51 Milk system rinsing 51

Permanent settings in programming mode 47 Powder chute

Powder chute for ground coffee 37 Preparation 43

Cappuccino 43

Coffee 43

Espresso 43

Espresso doppio 43

Espresso macchiato 43

Flat white 43

Ground coffee 44

Hot water 45

Latte macchiato 43

Ristretto 43 Problems

Troubleshooting 58 Product settings

Adjusting 48 Programming mode 47

Automatic switch-off 48

Energy-saving mode 49

Language 50 Restore factory settings 49 Setting the water hardness 49 Unit for amount of water 49

Proper use 38

Regular maintenance 46 Rinsing

Machine 50

Ristretto 43

Safety 38 Safety information 38 Service socket 37 Settings

Permanent settings in programming mode 47

Setting up

Setting up the machine 40 Smart Connect 37 Spout

Height-adjustable dual spout 36

Hot-water spout 36 Switching off 46 Switching on 46 Switch-off

Automatic switch-off 48 Symbol description 35

Technical data 59

Milk system 59 Tel 62 Transport 59 Troubleshooting 58

Unit for amount of water 49 Use, First-time 41

Water hardness

Determining the water hardness 41

Setting the water hardness 49 Water tank 36

Descaling 56

Filling 45 Website 40

11 JURA contact details/ Legal information

11 JURA contact details/ Legal

information

JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +41 (0)62 38 98 233

@ You will find additional contact details for

your country at www.jura.com.

@ If you need assistance with using

your machine, you can find this at

www.jura.com/service.

Directives

The machine complies with the following directives:

2014/35/EU– Low Voltage Directive

2014/30/EU– Electromagnetic Compatibility

2009/125/EC– Ecodesign Directive

2011/65/EU– RoHS Directive

Technical changes

We reserve the right to make technical changes. The diagrams used in these instructions for use are for illustration purposes only and do not represent the original colours of the machine. Some details of your ENA may vary.

Feedback

Your opinion is important to us! Use the contact details at www.jura.com.

The instructions for use contain information which is protected by copyright. It is not permitted to photocopy these instructions for use or translate them into another language without the prior written consent of JURA Elektroapparate AG.

J73913/ENA 8/de-ru/201804

11 Контакты с компанией JURA/ правовая информация

260

JURA 15292 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual