JURA 15044 User Manual

F9 Instructions for Use

Table of contents

Your F9

Control elements 4 Important information 6

Proper use ......................................................................................................................................................6

For your safety ...............................................................................................................................................6

1 Preparing and using for the first time 10

JURA on the Internet ....................................................................................................................................10

Setting up the machine ..............................................................................................................................10

Filling the bean container ...........................................................................................................................10

First-time use ................................................................................................................................................10

Determining the water hardness ..............................................................................................................13

Connecting milk ...........................................................................................................................................14

Filling the water tank ...................................................................................................................................14

2 Preparation 15

Ways of preparing a beverage ................................................................................................................... 15

Ristretto, espresso and coffee ....................................................................................................................16

Two ristretti, two espressi and two coffees .............................................................................................16

Latte macchiato, cappuccino and other speciality coffees with milk .................................................17

Ground coffee ...............................................................................................................................................18

Permanently setting the amount of water for the cup size .................................................................19

Adjusting the grinder .................................................................................................................................20

Hot water ......................................................................................................................................................20

3 Daily operation 21

Switching on the machine ..........................................................................................................................21

Daily maintenance .......................................................................................................................................21

Regular maintenance .................................................................................................................................22

Switching off the machine .........................................................................................................................22

4 Permanent settings in programming mode 23

Product settings ..........................................................................................................................................24

Adjusting the product settings .................................................................................................................24

Replacing products on the start screen ..................................................................................................25

Renaming a product ...................................................................................................................................26

Automatic switch-off .................................................................................................................................. 27

Energy-saving mode ..................................................................................................................................28

Maintenance settings .................................................................................................................................28

Setting the water hardness .......................................................................................................................29

Display settings ...........................................................................................................................................30

Unit for amount of water ...........................................................................................................................30

Restore factory settings ..............................................................................................................................31

Language .......................................................................................................................................................31

Querying information ................................................................................................................................32

Table of contents

5 Maintenance 33

Rinsing the machine ...................................................................................................................................33

Rinsing the milk system ............................................................................................................................. 34

Cleaning the milk system ..........................................................................................................................34

Dismantling and rinsing the dual spout ................................................................................................. 35

Inserting and activating the filter .............................................................................................................36

Changing the filter ...................................................................................................................................... 37

Cleaning the machine ................................................................................................................................39

Descaling the machine ..............................................................................................................................40

Descaling the water tank ........................................................................................................................... 42

Cleaning the bean container .....................................................................................................................42

6 Display messages 43 7 Troubleshooting 44 8 Transport and environmentally friendly disposal 45

Transport/ Emptying the system .............................................................................................................45

Disposal .........................................................................................................................................................45

9 Technical data 46 10 Index 47 11 JURA contact details/ Legal information 52

Symbol description

Warnings

J WARNING

J CAUTION

CAUTION CAUTION draws your attention to potential damage to the machine.

Symbols used

‘Espresso’ Display

Always take note of any information marked with the words CAUTION or WARNING and a warning sign. The signal word WARNING draws your attention to potential serious injury, and the signal word CAUTION to potential minor injury.

Prompt to take action. This symbol means that you are being prompted to perform some action.

Information and tips to make it even easier to use your F9.

Control elements

8 9

1 2

1 Bean container with aroma preservation

cover 2 Water tank cover 3 Water tank 4 Power switch and mains cable 

(back of the machine) 5 Coffee grounds container 6 Drip tray 7 Cup grille

13 14

8 Filler funnel cover 9 Filler funnel for ground coffee 10 Storage compartment cover 11 Grinder adjustment switch 12 Measuring spoon for ground coffee 13 Hot-water spout 14 Height-adjustable dual spout

Control elements

31 2

5 6

Top of the machine

1 Q On/Off button 2 g Rotary Switch 3 O P button (programming)

Front

4 Display 5 Multi-function buttons (button function

depends on what is shown in the display)

6 l Switch for hot water preparation

Important information

Proper use

For your safety

The machine is designed and intended for private domestic use. It should only be used for coffee preparation and to heat milk and water. Use for any other purpose will be deemed improper. JURA Elektroapparate AG cannot accept any responsibility for the consequences of improper use.

Before using the machine read these instructions for use thoroughly and completely and comply with the instructions they contain. A warranty service is not applicable for damage or defects caused by non-compliance with the instructions for use. Keep these instructions for use close to the machine and pass them on to the next user.

Please carefully read and observe the important safety information set out below.

To avoid danger of potentially fatal electric shock:

Never use a machine which is damaged or has

a defective mains cable. In the event of signs of damage, for example if

there is a smell of burning, unplug the machine immediately from the mains supply and contact JURA service. If the mains cable of this machine is damaged,

it must be repaired either directly by JURA or by an authorised JURA service centre. Make sure that the F9 and the mains cable are

not located close to hot surfaces. Be careful to ensure that the mains cable is not

trapped and does not rub against sharp edges.

Important information

Never open and repair the machine yourself.

Do not modify the machine in any way that is not described in these instructions for use. The machine contains live parts. If opened, there is a danger of potentially fatal injury. Repairs may only be carried out by authorised JURA service centres, using original spare parts and accessories. To completely and safely disconnect the

machine from the power supply, first switch off the F9 using the On/Off button and then at the power switch. Only then should you remove the mains plug from the power socket.

There is a risk of scalds or burns on the spouts.

Place the machine out of the reach of children.

Do not touch any hot parts. Use the handles

provided.

A defective machine is not safe and could cause injury or fire. To avoid damage and any associated risk of injury or fire:

Never allow the mains cable to loosely hang

down. The mains cable could pose a tripping hazard or become damaged. Protect the F9 from environmental influences

such as rain, frost and direct sunlight. Do not immerse the F9, mains cable or

connections in water. Do not put the F9 or any individual parts in the

dishwasher. Switch your F9 off at the power switch before

any cleaning operation. Always wipe the F9 with a damp cloth rather than a wet one, and protect it from prolonged exposure to water splash.

Important information

Only connect the machine to the mains volt-

age in accordance with the information on the rating plate. The rating plate is located on the underside of your F9. Further technical data is provided in these instructions for use (see Chapter 9 ‘Technical data’). Connect the F9 directly to a domestic power

socket. Using multi-socket adapters or extension cords may cause overheating. Please only use original JURA maintenance

products. Use of products that are not explicitly recommended by JURA could damage the F9. Do not use any coffee beans treated with addi-

tives or caramelised coffee beans. Only fill the water tank with fresh, cold water.

Switch the machine off at the power switch if

you are going to be absent for a longer period of time. Children may not clean or service the machine

unless supervised by a responsible person. Do not allow children to play with the machine.

Keep children under the age of 8 away from

the machine, or supervise them constantly. Children aged 8 and over may only operate

the machine without supervision if they have been instructed in how to use it safely. Children must be able to recognise and understand the potential dangers arising from incorrect use.

Important information

People, including children, who

do not have the physical, sensory or mental

capabilities to use the machine safely or are inexperienced or lack knowledge in how to

use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it correctly.

Safety when handling the CLARIS Blue filter cartridge:

Filter cartridges should be kept out of the

reach of children.

Store filter cartridges in a dry place in the

sealed packaging.

Protect cartridges from heat and direct sun-

light.

Do not use damaged filter cartridges.

Do not open filter cartridges.

1 Preparing and using for the first time

JURA on the Internet

Setting up the machine

Filling the bean container

CAUTION

Visit us on the Internet. You can download short operating instructions for your machine from the JURA website (www.jura.com). You

will also find interesting and up-to-date information on your F9 and on every aspect of coffee.

When setting up your F9, please note the following:

Place the F9 on a horizontal surface that is not sensitive to

water.

Choose a spot for your F9 which protects the machine against

overheating. Ensure that the ventilation slots are not covered.

Coffee beans which have been treated with additives (e.g. sugar), ground coffee or freeze-dried coffee will damage the grinder.

T Only use roasted, untreated coffee beans to fill the bean con-

tainer.

First-time use

T Remove the aroma preservation cover.

T Remove any dirt or foreign objects from inside the bean

container.

T Fill the bean container with coffee beans and close the

aroma preservation cover.

When using the machine for the first time, you can choose whether you want to operate F9 with or without the CLARIS Blue filter cartridge. If the water hardness is 10 °dH or more, we recommend using the filter cartridge. If you do not know the hardness of your water, you can find this out first (see Chapter 1 ‘Preparing and using for the first time – Determining the water hardness’).

1 Preparing and using for the first time

WARNING

First-time use with filter

cartridge activation

If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock.

T Never use a machine which is damaged or has a defective

mains cable.

Precondition:The bean container has been filled.

T Insert the mains plug into a power socket.  3 T Switch on the F9 using the power switch on the back of the

machine.

 Q T Press the On/Off button to switch the F9 on.

The display shows the languages you can choose from.

E To display more languages, press the

‘ > ’ button (bottom

right).

T Press the button that corresponds to the language you want,

e.g.

‘English’. ‘Saved’ appears briefly on the display to confirm the setting. ‘Use filter’

E Now decide whether you want to operate your F9 with or

without a CLARIS Blue filter cartridge.

CAUTION

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Press the T Press the

‘Ac tiv e’ button.

‘Save’ button. ‘Saved’ appears briefly on the display. ‘Insert filter’

T Remove the water tank and rinse it with cold water. T Open the filter holder and insert the filter cartridge into the

water tank, exerting slight pressure.

T Close the filter holder. It will click into place audibly.

E After two months, the filter will cease to work. Set the date on

the date plate on the filter holder in the water tank.

1 Preparing and using for the first time

T Fill the water tank with fresh, cold water and reinsert the

tank.

T Press the

‘Next’ button. ‘Switch open’

T Place a receptacle under the hot-water spout and dual spout.

 l T Turn the switch to them position.

‘Filter is being rinsed’, water flows out of the hot-water

spout.

E You can interrupt rinsing of the filter at any time. To do this,

turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter.

E The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately 300ml.

‘Switch close’ appears on the display.

 y T Turn the switch to the °position.

‘System is filling’, the system fills up with water. ‘Machine is heating’, the machine heats up. ‘Machine is rinsing’, the system is rinsed. The rinse stops

automatically.

‘Please select product’ appears on the display.

Your F9 is ready for use.

First-time use without filter

cartridge activation

CAUTION

E The display shows the products you can prepare.

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Press the T Press the

‘Inactive’ button.

‘Save’ button. ‘Saved’ appears briefly on the display. ‘Water hardness’

E If you do not know the hardness of your water, you must find

this out first (see Chapter 1 ‘Preparing and using for the first time – Determining the water hardness’).

1 Preparing and using for the first time

 g T Turn the Rotary Switch to change the water hardness set-

ting, e.g. to

T Press the

‘Saved’ appears briefly on the display. ‘Fill water tank.’

T Remove the water tank and rinse it with cold water. T Fill the water tank with fresh, cold water and reinsert the

tank.

‘Switch open’

T Place a receptacle under the hot-water spout and dual spout.

 l T Turn the switch to them position.

‘System is filling’, water flows out of the hot-water spout.

The operation stops automatically. the display.

 y T Turn the switch to the °position.

‘System is filling’, the system fills up with water. ‘Machine is heating’, the machine heats up. ‘Machine is rinsing’, the system is rinsed. The rinse stops

automatically. Your F9 is ready for use.

‘25°dH’.

‘Save’ button.

‘Switch close’ appears on

‘Please select product’ appears on the display.

Determining the water hardness

E The display shows the products you can prepare.

You can find out what the water hardness is by using the Aquadur® test strip supplied as standard.

T Hold the test strip briefly (for 1second) under flowing water.

Shake off the water.

T Wait for about 1minute. T You will then be able to read the degree of water hardness

from the discolouration of the Aquadur® test strip and the description on the packaging.

1 Preparing and using for the first time

Connecting milk

Filling the water tank

Your F9 creates fine, creamy, feather-light milk foam with a perfect consistency. The most important requirement for frothing milk is a milk temperature of 4–8°C. We would therefore recommend using a milk cooler or a vacuum milk container.

T Remove the protective cover from the dual spout.

T Connect the milk pipe to the dual spout. T Connect the other end of the milk pipe to a milk container

or immerse it in a milk carton.

Daily maintenance of the machine and hygiene when handling milk, coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily.

CAUTION

Milk, sparkling mineral water or other liquids can damage the water tank or the machine.

T Only fill the water tank with fresh, cold water.

T Open the water tank cover. T Remove the water tank and rinse it with cold water. T Fill the water tank with fresh, cold water and reinsert the

tank.

T Close the water tank cover.

2 Preparation

E You can stop the machine at any time while a speciality coffee

or hot water is being prepared. Just press any button (for a speciality coffee) or return the switch to its original position (for hot water preparation).

E During the grinding operation you can select the coffee

strength of single products by turning the Rotary Switch g.

E During preparation, you can change the preset amount of

water or milk foam by turning the Rotary Switch g.

E You can follow the current status of preparation on the display.

Coffee tastes best served hot. A cold porcelain cup cools the beverage – and impairs the taste. We therefore recommend prewarming the cups. The full coffee aroma can develop only in prewarmed cups. You can purchase a JURA cup warmer from your specialised dealer.

You can make permanent settings for all products in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).

Ways of preparing a beverage

The F9 offers various ways of preparing a speciality coffee, milk foam or hot water:

Preparation using the start screen: Simply press the corre-

sponding preparation button for the product shown on the display (start screen) that you want. The following products are displayed as standard on the start screen:

‘Espresso’

‘Coffee’

‘Flat white’

‘Latte macchiato’

Using the product selector view (Rotary Selection): Only

some of the products you can prepare are shown on the start screen. As soon as you turn the Rotary Switch, more products are displayed in a product selector view. Turn the Rotary Switch to bring the product you want into focus. Start preparation by pressing the Rotary Switch or the

‘Prepare’ button.

2 Preparation

The following additional products are shown in the product selector view:

‘Ristretto’

‘2 ristretti’

‘2 espressi’

‘2 coffees’

‘Special’

‘Cappuccino’

‘Macchiato’

‘Caffè latte’

‘Portion milk foam’

E The product selector view disappears automatically after

10seconds if no preparation is started.

E You have the option of replacing the four products on the start

screen with your personal favourites (see Chapter 4 ‘Permanent settings in programming mode – Replacing products on the start screen’). Please note that the descriptions provided in the following sections always refer to the default settings.

Ristretto, espresso and coffee

Two ristretti, two espressi and two coffees

Example:Proceed as follows to prepare one coffee. Precondition:

T Place a cup under the dual spout. T Press the

There are several ways of preparing two speciality coffees.

Using the product selector view:

When preparing a single product:

‘Please select product’ is displayed.

‘Coffee’ button.

Preparation starts. played. The preset amount of water for coffee flows into the cup. Preparation stops automatically. appears on the display.

Bring one of the double products ‘2 ristretti’, ‘2 espressi’ or

‘2 coffees’ into focus and press the Rotary Switch or the but-

ton

‘Prepare’.

Press the single product button twice within 2 seconds to

start preparing the relevant double product.

‘Coffee’ and the coffee strength are dis-

‘Please select product’

2 Preparation

Example:Proceed as follows to prepare two coffees (using product

selector view). Precondition:The start screen is displayed.

T Place two cups under the dual spout.  g T Turn the Rotary Switch to view the product selector.  g T Turn the Rotary Switch until the

focus.

 k T Press the Rotary Switch to start preparation.

Coffee preparation starts. The preset amount of water for coffee flows into the cups. Preparation stops automatically. Your F9 is once more ready for use.

‘2 coffees’ product is in

Latte macchiato, cappuccino and other speciality coffees with m i l k

Your F9 prepares latte macchiato, cappuccino, flat white and other speciality coffees with milk at the touch of a button. There is no need to move the glass or cup.

Example:Proceed as follows to prepare one latte macchiato. Precondition:

to the dual spout.

T Place a glass under the dual spout.

T Press the

E There is a short interval while the hot milk separates from the

milk foam. This allows the typical layers of a latte macchiato

to form.

To ensure that the milk system in the dual spout always works properly, you must clean it daily (see Chapter 5 ‘Maintenance – Cleaning the milk system’).

‘Please select product’ is displayed. Milk is connected

‘Latte macchiato’ button. ‘Latte macchiato’, the preset amount of milk foam flows into

the glass.

Coffee preparation starts. The preset amount of water for espresso flows into the glass. Preparation stops automatically.

‘Please select product’ appears on the display.

2 Preparation

Ground coffee

You can choose to use a second coffee variety, for example decaffeinated coffee, with the filter funnel for ground coffee.

E Never add more than two level measuring spoons of ground

coffee.

E Use ground coffee which is not ground too finely. Very fine

coffee can block up the system so that the coffee only comes out in drips.

E If you did not fill the machine with a sufficient amount of

ground coffee, the F9 stops the operation.

E The desired speciality coffee must be prepared within approx-

imately one minute after filling with the ground coffee. Otherwise the F9 stops the operation and is once more ready for use.

All speciality coffees with ground coffee are always prepared following the same model.

Example:Proceed as follows to prepare one espresso using ground coffee.

Precondition:

T Place an espresso cup under the coffee spout. T Open the cover of the filler funnel for ground coffee.

‘Please add ground coffee’

T Place one level measuring spoon of ground coffee into the

filler funnel.

T Close the cover of the filler funnel.

‘Please select product’

T Press the ‘Espresso’ button.

Preparation starts. espresso flows into the cup. Preparation stops automatically. appears on the display.

‘Not enough ground coffee’ is displayed and

‘Please select product’ is displayed.

‘Espresso’, the preset amount of water for

‘Please select product’

2 Preparation

Permanently setting the amount of water for the cup size

It is easy to permanently adjust the amount of water for all single products to the cup size. Adjust the amount once as shown in the

following example. Every time you prepare a drink in the future, this amount will be dispensed.

Example:Proceed as follows to permanently set the amount of water for one coffee.

Precondition:

T Place a cup under the dual spout. T Press and hold the

T Release the

T Press any button as soon as there is sufficient coffee in the

E You can alter this setting at any time by repeating the above

procedure.

E The amount can be permanently adjusted to the cup size for

the products shown in the product selector too. To do this, press and hold the Rotary Switch k until

Press button’

E You can also permanently set the amount of water for all spe-

ciality coffees and hot water in programming mode (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’).

‘Please select product’ is displayed.

‘Coffee’ button until ‘Enough coffee?

Press button’

Preparation starts and the coffee flows into the cup.

cup. Preparation stops. set amount of water for one coffee is permanently stored.

‘Please select product’ appears on the display.

appears.

‘Coffee’ button.

‘Saved’ appears briefly on the display. The

‘Enough coffee?

appears.

2 Preparation

Adjusting the grinder

CAUTION

You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee.

If you adjust the consistency of grind when the grinder is not operating, the grinder adjustment switch could be damaged.

T Only adjust the consistency of grind when the grinder is run-

ning.

The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.

Example:Proceed as follows to change the consistency of grind during the preparation of an espresso.

T Place a cup under the coffee spout. T Open the storage compartment cover. T Press the T Turn the grinder adjustment switch to the desired position

while the grinder is running. The preset amount of water flows into the cup. Preparation stops automatically.

T Close the storage compartment cover.

‘Espresso’ button to start preparation.

Hot water

CAUTION

There is a danger of scalding from hot water splashes.

T Avoid direct contact with the skin.

Precondition:

T Place a cup under the hot-water spout.

 l T Turn the switch to them position.

 y T Turn the switch to the °position.

‘Please select product’ is displayed.

‘Hot water’, the preset amount of water flows into the cup.

Preparation stops automatically.

‘Switch close’

‘Please select product’ appears on the display.

3 Daily operation

Switching on the machine

Daily maintenance

Daily maintenance of the machine and hygiene when handling milk, coffee and water are key to a perfect coffee result in the cup every time. You should therefore change the water daily.

Precondition:Your F9 is switched on at the power switch.

T Place a receptacle under the dual spout.

 Q T Press the On/Off button to switch the F9 on.

‘Welcome to JURA’ ‘Machine is heating’ ‘Machine is rinsing’

automatically. Your F9 is ready for use.

To ensure that you get many years of reliable service out of your F9 and to guarantee the optimum coffee quality, the machine requires daily maintenance.

T Pull out the drip tray. T Empty the coffee grounds container and the drip tray. Rinse

them both with warm water.

E Always empty the coffee grounds container when the machine

is switched on. This is the only way of resetting the coffee grounds counter.

, the system is rinsed. The rinse stops

‘Please select product’ appears on the display.

T Refit the coffee grounds container and the drip tray. T Rinse the water tank with clean water. T Remove the milk pipe and rinse it thoroughly under running

water.

T Dismantle and rinse the dual spout (see Chapter 5 ‘Mainte-

nance – Dismantling and rinsing the dual spout’).

T Wipe the surface of the machine with a clean, soft, damp

cloth (e.g. microfibre cloth).

3 Daily operation

Regular maintenance

Switching off the machine

Carry out the following maintenance actions regularly or as required:

In the interests of hygiene, we recommend changing the milk

pipe on a regular basis (approximately every 3 months). Replacement pipes are available from specialised dealers (JURA original accessory set for frothers). Clean the inside of the water tank, e.g. with a brush. Further

information about the water tank is provided in these instructions for use (see Chapter 5 ‘Maintenance – Descaling the water tank’). Traces of milk and coffee may stick to the top and bottom of

the cup grille. If this happens, clean the cup grille.

When the F9 is switched off, the system is automatically rinsed if a speciality coffee has been prepared.

Precondition:

system’

T Place a receptacle under the dual spout.

 Q T Press the On/Off button.

‘Please select product’ is displayed (or ‘Rinse the milk

if milk has been prepared).

If milk has been prepared, the milk system is first rinsed (

‘Milk system is being rinsed’). ‘Machine is rinsing’, the system rinses itself. The operation

stops automatically. Your F9 is switched off.

E When the F9 is switched off with the On/Off button, the

machine consumes less than 0.1W of standby energy. The machine can be completely disconnected from the power supply using the power switch.

4 Permanent settings in programming mode

Press the P button to enter programming mode. You can navigate through the programme items and permanently save the required settings simply by turning the Rotary Switch and using the multifunction buttons. The following settings can be made:

Programme item Sub-item Explanation

‘Maintenance status’

(

‘1/7’ and ‘2/7’)

‘Product settings’

(

‘3/7’)

‘Machine settings’

(

‘4/7’)

‘Machine settings’

(

‘5/7’)

‘Maintenance settings’

(

‘6/7’)

‘Information’ (‘7/7’) ‘Product counter’,

‘Clean’, ‘Change the filter’ (only

if filter is activated),

‘Descale’ (only if filter is

not activated),

‘Cappuccino cleaning’, ‘Rinse the coffee system’, ‘Rinse the milk system’ ‘Expert mode’, ‘Factory setting’

‘Choose language’, ‘Switch off after’, ‘Save energy’, ‘Factory setting’

‘Units’, ‘Display’

‘Use filter’, ‘Water hardness’ (only if

filter is not activated),

‘Switch-on rinse’

‘Maintenance counter’, ‘Version’

T Start the required maintenance pro- gramme here.

T Select your settings for speciality coffees and hot water. T Reset the settings for single products to their factory setting.

T Select your language. T Set the time after which the F9 should

switch off automatically.

T Select an energy-saving mode. T Reset the machine to its factory setting.

T Select the unit for the amount of water. T Change the display settings.

T Indicate whether you are operating your F9

with or without a CLARIS Blue filter cartridge.

T Adjust the water hardness. T Change the settings for switch-on rinse.

T Keep track of all products prepared and

view the number of maintenance programmes performed.

4 Permanent settings in programming mode

Product settings

Adjusting the product settings

Product Coffee strength Amount More settings

Ristretto, Espresso, Coffee, Special coffee 2 ristretti, 2 espressi, 2 coffees Cappuccino, Latte macchiato, Espresso macchiato, Caffè latte, Flat white Portion of milk foam Hot water – Water: 25ml–450ml Temperature (low,

8 levels Amount of coffee:

In the programme item ‘Product settings’ (‘3/7’) you can make the following settings:

‘Expert mode’

Set individual settings for all speciality coffees, milk and hot

water (see Chapter 4 ‘Permanent settings in programming mode – Adjusting the product settings’). Replace the products on the start screen with your favour-

ites (see Chapter 4 ‘Permanent settings in programming mode – Replacing products on the start screen’). Change the names of individual products (see Chapter 4

‘Permanent settings in programming mode – Renaming a product’).

‘Factory setting’

Reset the set values for individual products to their factory

setting.

In the programme item can make individual settings for all speciality coffees and hot water. The following permanent settings can be made:

25ml–240ml

– Amount of coffee: The amount

set for the single product is doubled.

25ml–240ml Milk foam: 0sec.–120sec. Interval: 0sec.–120sec. (not for caffè latte and flat white)

– Milk foam: 0sec.–120sec. Product name

‘Product settings’ (‘3/7’) / ‘Expert mode’ you

Temperature (normal, high), Product name

Temperature (as for single product), Product name Temperature (normal, high), Product name

normal, high), Product name

4 Permanent settings in programming mode

Permanent settings in programming mode always follow the same model.

Example:Proceed as follows to change the coffee strength for one coffee.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

E Next select the button of the product for which you would like

to make settings. No product is prepared at this point.

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Product settings’ (‘3/7’) is dis-

played.

‘Expert mode’ button.

‘Expert mode’

Replacing products on the start screen

T Press the

played.

T Press the

‘Coffee’

T Press the ‘Coffee strength’ button.

‘Coffee’ / ‘Coffee strength’

 g T Turn the Rotary Switch to change the coffee strength set-

ting.

T Press the

‘Saved’ appears briefly on the display. ‘Coffee’

 O T Press the P button to exit programming mode.

‘Please select product’

You have the option of replacing the four products on the start screen with your personal favourites.

Example:Proceed as follows to replace start screen with

Precondition:

 O T Press the P button.

‘Maintenance status’ (‘1/7’)

 g T Turn the Rotary Switch until

played.

‘ > ’ button (bottom right) until ‘Coffee’ is dis-

‘Coffee’ button.

‘Save’ button.

‘Latte macchiato’ on the

‘Macchiato’.

‘Please select product’ is displayed.

‘Product settings’ (‘3/7’) is dis-

4 Permanent settings in programming mode

 g T Press the ‘>’ button (bottom right) until ‘Add to favourites’

 O T Press the P button to exit programming mode.

T Press the ‘Expert mode’ button.

‘Expert mode’

T Press the ‘ > ’ button (bottom right) several times until

‘Macchiato’ is displayed.

T Press the

‘Macchiato’

is displayed.

T Press the

‘Select position’

T Press the ‘Latte macchiato’ button.

‘Select position’ / ‘Do you want to replace the current product?’

T Press the ‘Yes’ button.

‘Saved’ appears briefly on the display. ‘Macchiato’

‘Please select product’

‘Macchiato’ button.

‘Add to favourites’ button.

Renaming a product

In the programme item ‘Product settings’ / ‘Expert mode’ you can rename all of the products.

Example: Proceed as follows to change the product name of

‘Espresso’.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

T Press the ‘>’ button (bottom right) until ‘Espresso’ is dis-

T Press the

T Press the ‘>’ button (bottom right) until ‘Product name’ is

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Product settings’ (‘3/7’) is dis-

played.

‘Expert mode’ button.

‘Expert mode’

played.

‘Espresso’ button.

‘Espresso’

displayed.

4 Permanent settings in programming mode

T Press the ‘Product name’ button.

The available letters, numbers and special characters appear on the display.

Automatic switch-off

E By pressing the

lower and upper case letters.

 g T Turn the Rotary Switch until the letter you want is high-

lighted.

 k T Press the Rotary Switch to confirm the letter.

T Continue until the new product name you want is displayed.

E Please note that there is a maximum text length.

T Press the

‘Saved’ appears briefly on the display.

The new product name is displayed.

 O T Press the P button to exit programming mode.

‘Please select product’

By instructing your F9 to automatically switch itself off, you can cut down your energy consumption. If this function is activated, your F9 switches off automatically after the preset time following the last action on the machine.

You can set the automatic switch-off to 15minutes, 30minutes or 1–9hours.

Precondition:

 O T Press the P button.

‘Maintenance status’ (‘1/7’)

 g T Turn the Rotary Switch until

played.

T Press the

‘Switch off after’

 g T Turn the Rotary Switch to change the switch-off time (e.g. to

‘2hrs.’).

T Press the

‘Saved’ appears briefly on the display. ‘Machine settings’

 O T Press the P button to exit programming mode.

‘Please select product’

‘abc/ABC’ button, you can switch between

‘Save’ button.

‘Please select product’ is displayed.

‘Machine settings’ (‘4/7’) is dis-

‘Switch off after’ button.

‘Save’ button.

4 Permanent settings in programming mode

Energy-saving mode

In the programme item ‘Machine settings’ (‘4/7’) / ‘Save energy’ you can permanently set an energy-saving mode (Energy Save Mode,

E.S.M.

‘Ac tiv e’

Soon after the last preparation, the F9 stops heating up.

After about 5 minutes the message played. Before you can prepare a speciality coffee, speciality coffee

with milk, or hot water, the machine must heat up.

‘Inactive’

All speciality coffees, speciality coffees with milk and hot

water can be prepared without having to wait.

Example:Proceed as follows to change the energy-saving mode from

‘Ac tiv e’ to ‘Inactive’.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

T Press the ‘Inactive’ button. T Press the

 O T Press the P button to exit programming mode.

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Machine settings’ (‘4/7’) is dis-

played.

‘Save energy’ button.

‘Save energy’

‘Save’ button. ‘Saved’ appears briefly on the display. ‘Machine settings’

‘Please select product’

‘Energy Save’ is dis-

Maintenance settings

In the programme item ‘Maintenance settings’ (‘6/7’) you can make the following settings:

‘Use filter’

Activate the CLARIS Blue filter cartridge (see Chapter 5

‘Maintenance – Inserting and activating the filter’).

‘Water hardness’ (only if filter is not activated)

If you do not have a filter cartridge, you will need to set the

water hardness (see Chapter 4 ‘Permanent settings in programming mode – Setting the water hardness’).

4 Permanent settings in programming mode

‘Switch-on rinse’

‘Manual’: The switch-on rinse must be started manually.

‘Automatic’: The switch-on rinse is started automatically.

Example: Proceed as follows to specify that the switch-on rinse should be started manually.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

T Press the ‘Manual’ button. T Press the

 O T Press the P button to exit programming mode.

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Maintenance settings’ (‘6/7’) is

displayed.

‘Switch-on rinse’ button. ‘Switch-on rinse’

‘Save’ button. ‘Saved’ appears briefly on the display. ‘Maintenance settings’

‘Please select product’

Setting the water hardness

E If you are using the CLARIS Blue filter cartridge and have acti-

vated it, it is not possible to set the water hardness.

The harder the water is, the more frequently the F9 needs to be descaled. It is therefore important to set the water hardness accurately.

The water hardness can be adjusted on a continuous scale between 1 °dH and 30 °dH.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

 g T Turn the Rotary Switch to adjust the water hardness.

T Press the

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Maintenance settings’ (‘6/7’) is

displayed.

‘Water hardness’ button. ‘Water hardness’

‘Save’ button. ‘Saved’ appears briefly on the display. ‘Maintenance settings’

4 Permanent settings in programming mode

 O T Press the P button to exit programming mode.

‘Please select product’

Display settings

Unit for amount of water

In the programme item ‘Machine settings’ (‘5/7’) / ‘Display’ you can set the display brightness and contrast (as a percentage).

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

 g T Turn the Rotary Switch to change the display setting.

T Press the

 O T Press the P button to exit programming mode.

In the programme item ‘Machine settings’ (‘5/7’) / ‘Units’ you can select the unit used for the amount of water.

Example:Proceed as follows to change the unit for the amount of water from

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

T Press the ‘oz’ button. T Press the

 O T Press the P button to exit programming mode.

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Machine settings’ (‘5/7’) is dis-

played.

‘Display’ button. ‘Display’

‘Save’ button. ‘Saved’ appears briefly on the display. ‘Machine settings’

‘Please select product’

‘ml’ to ‘oz’.

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Machine settings’ (‘5/7’) is dis-

played.

‘Units’ button. ‘Units’

‘Save’ button. ‘Saved’ appears briefly on the display. ‘Machine settings’

‘Please select product’

4 Permanent settings in programming mode

Restore factory settings

Language

In the programme item ‘Machine settings’ (‘4/7’) / ‘Factory setting’ the machine can be reset to its factory setting: All user settings (apart from the ‘filter’ and ‘water hardness’) are reset to factory settings. Your F9 then switches off.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

T Press the ‘Yes’ button.

In this programme item you can set the language used by your F9.

Example:Proceed as follows to change the language from to

‘Deutsch’.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Machine settings’ (‘4/7’) is dis-

played.

‘Factory setting’ button. ‘Factory setting’ / ‘Reset the machine to the factory settings?’

‘Saved’ appears briefly on the display.

Your F9 is switched off.

‘English’

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Machine settings’ (‘4/7’) is dis-

played.

‘Choose language’ button. ‘Choose language’

E To display more languages, press the ‘ > ’ button (bottom

right).

T Press the

‘Gespeichert’ appears briefly on the display. ‘Geräteeinstellungen’

 O T Press the P button to exit programming mode.

‘Bitte wählen’

‘Deutsch’ button.

4 Permanent settings in programming mode

Querying information

In the programme item ‘Information’ (‘7/7’) you can view the following information:

‘Product counter’: Number of prepared speciality coffees,

speciality coffees with milk and hot water

‘Maintenance counter’: Number of maintenance programmes

performed (cleaning, descaling etc.)

‘Version’: Software version

Example:Proceed as follows to view the number of speciality coffees prepared.

Precondition:

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

E Press the ‘>’ button (bottom right) to display the number of

additional speciality coffees.

 O T Press the P button to exit programming mode.

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Information’ (‘7/7’) is displayed.

‘Product counter’ button. ‘Product counter’

‘Please select product’

5 Maintenance

Your F9 has the following integrated maintenance programmes:

Rinsing the machine (‘Rinse the coffee system’)

Rinsing the milk system in the dual spout

(

‘Rinse the milk system’)

Cleaning the milk system in the dual spout (‘Cappuccino

cleaning’

Changing the filter (‘Change the filter’) (only if filter is acti-

vated) Cleaning the machine (‘Clean’)

Descaling the machine (‘Descale’) (only if filter is not acti-

vated)

E Clean or descale the machine, rinse the milk system or change

the filter when you are prompted to do so.

E Press the P button to view a list of the maintenance pro-

grammes ( can see which maintenance programme is due. When the bar is completely filled with red, your F9 will prompt you to perform the appropriate maintenance programme.

E In the interests of hygiene, you should clean the milk system

daily when you have been preparing milk.

)

‘Maintenance status’). By referring to the bar you

Rinsing the machine

You can initiate the rinse operation manually at any time.

Precondition:

T Place a receptacle under the dual spout.

 O T Press the P button.

 g T Turn the Rotary Switch until

T Press the

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Maintenance status’ (‘2/7’) is

displayed.

‘Rinse the coffee system’ button to initiate the

rinse operation.

‘Machine is rinsing’, water flows out of the dual spout.

The rinse stops automatically. appears on the display.

‘Please select product’

5 Maintenance

Rinsing the milk system

Cleaning the milk system

CAUTION

After each milk preparation, the F9 prompts you to perform a milk system rinsing.

Precondition:

T Place a receptacle under the dual spout.

 k T Press the Rotary Switch.

To ensure that the milk system in the dual spout always works properly, you must clean it daily when you have been preparing milk.

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

E JURA milk system cleaner is available from specialised dealers.

Precondition:

 O T Press the P button.

T Press the T Press the T Press the

T Remove the milk pipe from the milk container or carton. T Pour 250ml of fresh water into a receptacle and add one

T Immerse the milk pipe in the receptacle. T Place another receptacle under the dual spout. T Press the

T Rinse the receptacle thoroughly, fill it with 250ml of fresh

‘Rinse the milk system’ is displayed.

‘Milk system is being rinsed’, water flows out of the dual

spout. The rinse stops automatically. Your F9 is once more ready for use.

‘Please select product’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Cappuccino cleaning’ button. ‘Start’ button. ‘Start’ button again.

‘Cleaner for Cappuccino’

capful of milk system cleaner.

‘Next’ button. ‘Cleaning Cappuccino’, the dual spout and the pipe are

cleaned.

‘Water for Cappuccino’

water and immerse the milk pipe in the water.

5 Maintenance

T Empty the other receptacle and place it under the dual spout

again.

T Press the

‘Cleaning Cappuccino’, the dual spout and the pipe are

rinsed with fresh water. The operation stops automatically.

complete’

Your F9 is once more ready for use.

‘Next’ button.

‘Milk system cleaning

appears briefly on the display.

Dismantling and rinsing the dual spout

The dual spout must be dismantled and rinsed daily if milk has been prepared to make sure it functions perfectly and also in the interests of hygiene.

T Remove the milk pipe and rinse it thoroughly under running

water.

T Press the releasing devices and pull the dual spout down and

off.

T Press the milk system down and take it out.

5 Maintenance

T Dismantle the milk system into its individual parts. T Rinse all the parts under running water. If there are severely

dried-on milk residues, firstly immerse the individual parts in a solution of 250ml cold water and 1 capful of JURA milk system cleaner. Then rinse the parts thoroughly.

T Fit the air intake pipe.

T Reassemble the milk system. When doing this, note the

numbering of the individual parts.

1 2

T Fit the assembled individual part s back in the dual spout and

press it firmly.

Inserting and activating the filter

T Fit the dual spout on the machine. It will click into place audi-

bly.

Your F9 no longer has to be descaled if you are using the CLARIS Blue filter cartridge. If you did not activate the filter cartridge the first time you used the machine, you can do this now as follows.

E Perform the ‘inserting the filter’ operation without any inter-

ruptions. This will ensure that your F9 always produces its best.

Precondition:

‘Please select product’ is displayed.

 O T Press the P button.

‘Maintenance status’ (‘1/7’)

5 Maintenance

 g T Turn the Rotary Switch until ‘Maintenance settings’ (‘6/7’) is

displayed.

T Press the

‘Use filter’

T Press the ‘Ac tiv e’ button. T Press the

‘Saved’ appears briefly on the display. ‘Insert filter’

T Remove and empty the water tank. T Open the filter holder and insert the filter cartridge into the

water tank, exerting slight pressure.

T Close the filter holder. It will click into place audibly.

E After two months, the filter will cease to work. Set the date on

the date plate on the filter holder in the water tank.

T Fill the water tank with fresh, cold water and reinsert the

tank.

T Press the

‘Switch open’

T Place a receptacle under the hot-water spout.

 l T Turn the switch to them position.

‘Filter is being rinsed’, water flows out of the hot-water

spout.

‘Use filter’ button.

‘Save’ button.

‘Next’ button.

Changing the filter

E You can interrupt rinsing of the filter at any time. To do this,

turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter.

E The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately 300ml.

‘Switch close’ appears on the display.

 y T Turn the switch to the °position.

‘Please select product’ appears on the display. The filter is

now activated.

E After 50 litres of water have flowed through, the filter will

cease to work. Your F9 will automatically prompt you to change the filter.

5 Maintenance

E After two months, the filter will cease to work. Set the date on

the date plate on the filter holder in the water tank.

E If the CLARIS Blue filter cartridge is not activated in program-

ming mode, you will not be prompted to change the filter.

E CLARIS filter cartridges are available from specialised dealers.

Precondition:

‘Change the filter’ is displayed.

 O T Press the P button.

‘Maintenance status’ (‘1/7’)

T Press the

‘Change the filter’ button. ‘Change the filter’

T Press the ‘Start’ button. T Press the

‘Start’ button again. ‘Change filter’

T Remove and empty the water tank. T Open the filter holder and remove the old CLARIS Blue filter

cartridge.

T Insert a new CLARIS filter cartridge Blue into the water tank,

exerting slight pressure.

T Close the filter holder. It will click into place audibly. T Fill the water tank with fresh, cold water and reinsert the

tank.

T Place a receptacle under the hot-water spout. T Press the

‘Next’ button. ‘Switch open’

 l T Turn the switch to them position.

‘Filter is being rinsed’, water flows out of the hot-water

spout.

E You can interrupt rinsing of the filter at any time. To do this,

turn the switch clockwise. Turn the switch anticlockwise to continue rinsing the filter.

E The water may be slightly discoloured. This is not harmful to

health and does not affect the taste.

Rinsing of the filter stops automatically after approximately 300ml.

‘Switch close’ appears on the display.

 y T Turn the switch to the °position.

‘Please select product’ appears on the display.

5 Maintenance

Cleaning the machine

CAUTION

After 200preparations or 80switch-on rinses, the F9 will prompt you to clean it.

If the wrong cleaning agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

E The cleaning programme lasts approximately 20 minutes. E Do not interrupt the cleaning programme. The quality of

cleaning will be impaired if you do so.

E JURA cleaning tablets are available from specialised dealers.

Precondition:

 O T Press the P button.

T Press the

T Press the ‘Start’ button. T Press the

T Empty the drip tray and coffee grounds container and put

T Place a receptacle under the dual spout.

 k T Press the Rotary Switch.

T Open the cover of the filler funnel for ground coffee.

‘Clean machine’ is displayed.

‘Maintenance status’ (‘1/7’)

‘Clean’ button. ‘Clean’

‘Start’ button again. ‘Empty grounds’

them back into the machine.

‘Press the Rotary Switch’

‘Machine is being cleaned’, water flows out of the dual spout.

The operation is interrupted,

‘Add cleaning tablet’.

T Insert a JURA cleaning tablet into the filler funnel. T Close the cover of the filler funnel.

‘Press the Rotary Switch’

 k T Press the Rotary Switch.

‘Machine is being cleaned’, water flows out of the dual spout

repeatedly. The operation stops automatically.

‘Empty grounds’

5 Maintenance

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Please select product’ appears on the display. Cleaning is

now complete.

Descaling the machine

CAUTION

The F9 builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.

E If you use a CLARIS Blue filter cartridge and this is activated,

you will not be prompted to descale.

If the descaling agent comes into contact with the skin or eyes, this can cause irritation.

T Avoid contact with the skin or eyes. T Rinse off the descaling agent with clean water. Should you get

any descaling agent in your eye, see a doctor.

If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water.

T Use only original JURA maintenance products.

If the descaling operation is interrupted, there may be damage to the machine.

T Allow the descaling programme to run to the end.

If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out.

T Clean up any splashes immediately.

E The descaling programme lasts approximately 40minutes. E JURA descaling tablets are available from specialised dealers.

Precondition:

‘Decalcify machine’ is displayed.

 O T Press the P button.

‘Maintenance status’ (‘1/7’)

T Press the

‘Descale’ button. ‘Descale’

T Press the ‘Start’ button. T Press the

‘Start’ button again. ‘Empty drip tray’

5 Maintenance

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Agent in tank’

T Remove and empty the water tank. T Completely dissolve the contents of one blister (3JURA des-

caling tablets) in a receptacle holding 500ml of lukewarm water. This may take several minutes.

T Pour the solution into the empty water tank and insert it into

the machine.

‘Switch open’

T Place a receptacle under the hot-water spout and dual spout.

 l T Turn the switch to them position.

‘Machine is being descaled’, water flows out of the hot-water

spout repeatedly. The operation is interrupted,

‘Switch close’.

 y T Turn the switch to the °position.

‘Machine is being descaled’, the descaling operation is con-

tinued. Water flows out of the dual spout repeatedly. The operation is interrupted,

‘Empty drip tray’.

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Fill water tank.’

T Empty the receptacle and place it under the hot water and

dual spouts.

T Remove the water tank and rinse it thoroughly. T Fill the water tank with fresh, cold water and reinsert the

tank.

‘Switch open’

 l T Turn the switch to them position.

‘Machine is being descaled’, the descaling operation is con-

tinued. The operation is interrupted,

‘Switch close’.

 y T Turn the switch to the °position.

‘Machine is being descaled’, the descaling operation is con-

tinued. The operation is interrupted,

‘Machine is being descaled’.

Water flows out of the dual spout.

‘Empty drip tray’

5 Maintenance

T Empty the drip tray and coffee grounds container and put

them back into the machine.

‘Please select product’ appears on the display. Descaling is

now complete.

E If the descaling operation stops unexpectedly, rinse the water

tank thoroughly.

Descaling the water tank

Cleaning the bean container

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time.

T Remove the water tank. T If you use a CLARIS Blue filter cartridge, remove this. T Completely fill the water tank and dissolve 3 JURA descaling

tablets in it.

T Leave the water tank with the descaling solution for several

hours (e.g. overnight).

T Empty the water tank and rinse it thoroughly. T If you use a CLARIS Blue filter cartridge, insert this again. T Fill the water tank with fresh, cold water and reinsert the

tank.

Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time.

Precondition:

 Q T Switch the machine off with the On/Off button.  3 T Switch the machine off at the power switch.

T Remove the aroma preservation cover. T Clean the bean container with a soft, dry cloth. T Fill the bean container with coffee beans and close the

‘Fill bean container’ is displayed.

aroma preservation cover.

6 Display messages

Message Cause/Result Action

‘Fill water tank.’ The water tank is empty. You

cannot prepare any products.

‘Empty grounds’ The coffee grounds container is

full. You cannot prepare any products.

‘Drip tray not fitted’

‘Fill bean container’

‘Rinse the milk system’

‘Change the filter’ The filter cartridge no longer

‘Clean machine’ The F9 is prompting you to clean

‘Decalcify machine’

‘Not enough ground coffee’

‘Too hot’ The system is too hot to start a

The drip tray is not inserted correctly or is not inserted at all. You cannot prepare any products. The bean container is empty. You cannot prepare any products.

The F9 requests a milk system rinsing.

works.

it.

The F9 is prompting you to descale it.

There is insufficient ground coffee in the machine; the F9 stops the operation.

maintenance programme.

T Fill the water tank (see Chapter 1 ‘Preparing and using for the first time – Filling the water tank’).

T Empty the coffee grounds container and the drip tray (see Chapter 3 ‘Daily operation – Daily maintenance’).

T Fit the drip tray.

T Fill the bean container (see Chapter 1

‘Preparing and using for the first time – Filling the bean container’).

T Perform milk system rinsing (see Chapter 5 ‘Maintenance – Rinsing the milk system’).

T Replace the CLARIS Blue filter cartridge (see Chapter 5 ‘Maintenance – Changing the filter’).

T Perform cleaning (see Chapter 5 ‘Maintenance – Cleaning the machine’).

T Perform descaling (see Chapter 5 ‘Maintenance – Descaling the machine ’).

T The next time you prepare a beverage, add more ground coffee (see Chapter 2 ‘Preparation – Ground coffee’).

T Wait for several minutes until the system has cooled or prepare a speciality coffee or hot water.

6 Display messages

7 Troubleshooting

Problem Cause/Result Action

Insufficient foam is produced when the milk is frothed, or milk sprays from the dual spout.

Coffee only comes out in drips when it is being prepared.

Water hardness cannot be adjusted.

‘Fill water tank.’ is

displayed although the water tank is full.

Grinder is making a very loud noise.

‘Error2’ or ‘Error5’ is

displayed.

Other

‘Error’ messages

are displayed.

The dual spout is dirty.

Coffee or ground coffee has been ground too finely and is blocking the system. The same filter cartridge may have been used several times or the water hardness set incorrectly in the programming mode. The CLARIS Blue filter cartridge is activated.

The water tank float is trapped.

There are foreign objects in the grinder.

If the machine was exposed to the cold for a long period of time, heating is disabled for safety reasons.

–

T Clean the milk system in the dual spout (see Chapter 5 ‘Maintenance – Cleaning the milk system’). T Dismantle and rinse the dual spout (see Chapter 5 ‘Maintenance – Dismantling and rinsing the dual spout’).

T Put the grinder on a coarser setting or use coarser ground coffee (see Chapter 2 ‘Preparation – Adjusting the grinder’). T Perform descaling (see Chapter 5 ‘Maintenance – Descaling the machine ’).

T Deactivate the filter cartridge in programming mode.

T Descale the water tank (see Chapter 5 ‘Maintenance – Descaling the water tank’).

T Contact customer support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

T Warm the machine at room temperature.

T Switch the F9 off at the power switch. Contact customer support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

E If you were unable to solve the problem, contact customer

support in your country (see Chapter 11 ‘JURA contact details/ Legal information’).

8 Transport and environmentally friendly disposal

Transport/ Emptying the system

Keep the packaging for your F9. It should be used to protect the machine during transport.

In order to protect the F9 from frost during transport, the system must be emptied.

Precondition:

T Remove the milk pipe from the dual spout. T Place a receptacle under the hot-water spout.

 g T Turn the Rotary Switch to view the product selector.  g T Turn the Rotary Switch until the

 k T Press the Rotary Switch.

T Remove and empty the water tank. T Turn the Rotary Switch until

 Q T Press the On/Off button.

‘Please select product’ is displayed.

‘Portion milk foam’ product

is in focus.

‘Portion milk foam’, hot steam is discharged from the dual

spout.

‘Amount of milk’ ‘60 sec.’ is dis-

played. Steam will continue to be discharged from the dual spout until the system is empty.

‘Fill water tank.’

Your F9 is switched off.

Disposal

Please dispose of old machines in an environmentally neutral way.

Old machines contain valuable, recyclable materials which should be recycled. Please therefore dispose of old machines via suitable collection systems.

9 Technical data

Voltage 220–240V~, 50Hz Power 1450W Conformity mark

Energy consumption

‘Save energy’ / ‘Ac tive’

Energy consumption

‘Save energy’ / ‘Inactive’

Pump pressure static, max. 15bar Holding capacity of water tank 1.9l Holding capacity of bean container 310g Holding capacity of coffee grounds container Cable length approx. 1.1m Weight approx. 9.8kg Dimensions (W×H×D) 28.5 × 35.5 × 44.5cm

Information for testers (repeat test in accordance with DIN VDE 0701-0702): The central grounding point (CGP) is located on the underside of the machine, right next to the mains cable's connection point.

approx. 5Wh

approx. 16Wh

max. 15 portions

10 Index

Addresses 52 Adjusting the product settings 24 Aroma preservation cover

Bean container with aroma preservation cover 4

Automatic switch-off 27

Bean container

Bean container with aroma preservation cover 4 Cleaning 42 Filling 10

Bus bar

Technical data 46

Button

On/Off button 5 P button (programming) 5

Caffè latte 17 Cappuccino 17 Cappuccino frother cleaning

Cleaning the milk system 34

Cappuccino frother rinsing

Rinsing the milk system 34 Central grounding point 46 Changing a name 26 CLARIS Blue filter cartridge

Changing 37

Inserting and activating the filter 36 Classics 24 Cleaning

Bean container 42

Machine 39 Coffee 16

2 coffees 16 Coffee grounds container 4 Consistency of grind

Adjusting the grinder 20

Grinder adjustment switch 4 Contact details 52

Cover

Filler funnel for ground coffee 4 Storage compartment 4

Water tank 4 Cup grille 4 Customer support 52

Descaling

Machine 40

Water tank 42 Display 5 Display messages 43 Display settings 30 Disposal 45 Double product 16 Drip tray 4 Dual spout

Dismantling and cleaning 35

Height-adjustable dual spout 4

Emptying the system 45 Energy-saving mode 28 Errors

Troubleshooting 44 Espresso

2 espressi 16 Espresso 16 Espresso macchiato 17 Expert mode 24

Factory settings

Restore factory settings 31 Filler funnel

Filler funnel for ground coffee 4 Filling

Bean container 10

Water tank 14 Filter

Changing 37

Inserting and activating the filter 36 First-time use 10

With filter cartridge activation 11

Without filter cartridge activation 12 Flat white 17

10 Index

Grinder adjustment switch 4 Ground coffee 18

Measuring spoon for ground coffee 4

Grounding point 46

Hotline 52 Hot water 20 Hot water preparation

Switch for hot water preparation 5

Hot-water spout 4

Instant coffee

Ground coffee 18

Internet 10

JURA

Contact details 52 Internet 10

Language 31 latte macchiato 17

Machine

Cleaning 39 Descaling 40 Regular maintenance 22 Rinsing 33 Setting up 10 Switching off 22

Switching on 21 Mains cable 4 Maintenance 33

Daily maintenance 21

Regular maintenance 22 Maintenance settings 28 Measuring spoon for ground coffee 4 Messages, display 43 Milk

Connecting milk 14 Milk system

Cleaning 34

Rinsing 34

Permanently setting the water for the cup

size 19

Permanent settings in programming mode

23 Power switch 4 Preparation 15, 17

2 coffees 16 2 espressi 16 2 ristretti 16 At the touch of a button 15 Caffè latte 17 Cappuccino 17 Coffee 16 Espresso 16 Espresso macchiato 17 Flat white 17 Ground coffee 18 Hot water 20 Latte macchiato 17 Ristretto 16 Two speciality coffees 16

Using the product selector 15 Preparation options 15 Problems

Troubleshooting 44 Product selector view 15 Product settings 24

Adjusting 24 Programming mode 23

Automatic switch-off 27

Display settings 30

Energy-saving mode 28

Language 31

Maintenance settings 28

Product settings 24

Querying information 32

Renaming a product 26

Replacing products on the start screen

Restore factory settings 31

Setting the water hardness 29

Unit for amount of water 30 Proper use 6

Querying information 32

Regular maintenance 22 Renaming a product 26 Rinsing

Machine 33

Ristretto 16

2 ristretti 16 Rotary Selection 15 Rotary Switch 5

Safety 6 Safety information 6 Settings

Maintenance settings 28

Permanent settings in programming

mode 23 Setting up

Setting up the machine 10 Short operating instructions 10 Spout

Height-adjustable dual spout 4

Hot-water spout 4 Switch for hot water preparation 5 Switching off 22 Switching on 21 Switch-off

Automatic switch-off 27 Symbol description 3

Technical data 46 Tel 52 Transport 45 Troubleshooting 44 Two products 16

Unit for amount of water 30 Use, First-time 10

Water hardness

Determining the water hardness 13

Setting the water hardness 29 Water tank 4

Descaling 42

Filling 14 Website 10

10 Index

505152

J71806/F9/en/201703

11 JURA contact details/ Legal information

JURA Elektroapparate AG Kaffeeweltstrasse 10 CH-4626 Niederbuchsiten Tel. +41 (0)62 38 98 233

@ You will find additional contact details for your country at

www.jura.com.

Directives

Technical changes

Feedback

The machine complies with the following directives:

2014/35/EU– Low Voltage Directive

2014/30/EU– Electromagnetic Compatibility

2009/125/EC– Ecodesign Directive

2011/65/EU– RoHS Directive

We reserve the right to make technical changes. The diagrams used in these instructions for use are for illustration purposes only and do not represent the original colours of the machine. Some details of your F9 may vary.

Your opinion is important to us! Use the contact details at www.jura.com.

The instructions for use contain information which is protected by copyright. It is not permitted to photocopy these instructions for use or translate them into another language without the prior written consent of JURA Elektroapparate AG.

JURA 15044 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual