Page 1
Kühlschrank
Refrigerator
JKI 4033
JKI 4054
JKI 4064
Gebrauchsanweisung
Operating Instructions
Page 2
Dear customer,
Before placing your new refrigerator into operation
please read these operating instructions carefully.
They contain important information for safe use, for
installation and for care of the appliance.
Please keep these operating instructions for future
reference. Pass them on to possible new owners of
the appliance.
These operating instructions are for use with several
technically comparable models with varying accessories. Please observe the notes which apply to your
model.
1
1. Numbered instructions guide you step by step in
2. ...
3
2
Explanations of the technical terminology used in the
operating instructions can be found at the end in the
section "Technical Terminology".
The operating instructions contain instructions for the
correction of possible malfunctions by the user in the
section "What to do, if ...". If these instructions should
not be sufficient, please contact your local Service
Force Centre.
Notes which are important for your safety or
for the proper functioning of the appliance
are stressed with a warning triangle and/or
with signal words (Warning!, Caution!,
Attention!). Please observe the following
carefully.
the operation of the appliance.
Supplementary information regarding operation and practical applications of the appliance appear after this symbol.
Tips and notes concerning economical and
environmentally sound use of the appliance
are marked with the cloverleaf.
18
Page 3
Contents
Safety .......................................................................20
Disposal .....................................................................21
AppliancePackagingInformation ..................................................21
DisposalofoldAppliances........................................................21
Remove transport safeguard ....................................................21
Installation ...................................................................22
InstallationLocation.............................................................22
Yourrefrigeratorneedsventilation..................................................22
Installation ...................................................................22
Electricalconnection ............................................................23
Appliance Description ..........................................................23
ViewofAppliance ..............................................................23
Prior to Initial Start–Up .........................................................23
Starting up - Setting the temperature .............................................24
Switching off the appliance .....................................................24
Interior Accessories ...........................................................25
StorageShelves ...............................................................25
Bottle/canshelf ................................................................25
VariableInnerDoor .............................................................25
Variabledoorstoragecompartment ................................................26
Correct Storage ...............................................................26
Defrosting ....................................................................26
Thefridgedefrostsautomatically...................................................26
Cleaning and Maintenance ......................................................27
Energy Saving Tips ............................................................27
What to do if ... ................................................................28
CorrectingMalfunctions..........................................................28
Changingthelightbulb ..........................................................29
Noises during Operation ........................................................29
Regulations, Standards, Guidelines ..............................................29
Technical Terminology .........................................................30
Customer Service .............................................................30
Installation Instructions ........................................................31
19
Page 4
1 Safety
The safety aspects of our refrigerators comply with
accepted technical standards and the German Appliance Safety Law. Nevertheless, we consider it our
obligation to m ake you aware of the following safety
information:
Intended use
• The refrigerator is intended for use in the home. It
is suitable for the cooling and storing of food. If the
appliance is used for purposes other than those
intended or used incorrectly, no liability can be
accepted bythe manufacturer for any damage that
may be caused.
• Alterations or changes to the refrigerator are not
permitted for reasons of safety.
• If you use the refrigerator in a commercial application or for purposes other than the cooling of
foods,please observe all valid legal regulations for
your application.
Prior to initial start–up
• Check the refrigerator for transport damage.
Under no circumstance should a damaged appliance be plugged in! In the event of damage,
please contact the vendor.
Refrigerant
The refrigerant isobutane (R600a) is contained within
the refrigerant circuit of the appliance, a natural gas
with a high level of environmental compatibility, which
is nevertheless flammable.
• During transportation and installation of the appliance, be certain that none of the components of
the refrigerant circuit become damaged.
• If the refrigerant circuit should become damaged:
– avoid open flames and sources of ignition;
– thoroughly ventilate the room in which the
appliance is situated.
Safety of children
• Packaging (e.g. wraps, polystyrene) can be dangerous for children. There is a risk of suffocation!
Keep packaging material away from children!
• Please make old appliances unusable prior to disposal. Pull out the mains plug, cut off the mains
cable, break or remove spring or bolt catches, if fitted. By doing this you ensure that children cannot
lock themselves in the fridge when playing (there
is risk of suffocation!) or get themselves into other
dangerous situations.
• Often children cannot recognise the hazards
present in household appliances. It is therefore
important that you ensure adequate supervision
and never let children play with the appliance!
Daily Operation
• Containers with flammable gases or liquids can
leak at low temperatures. There is a risk of an
explosion! Do not store any containers with flammable materials such as, for example, spray cans,
fire extinguisher refill cartridges etc in the refrigerator.
• Do not operate any electrical appliances in the
refrigerator (e.g. electri c ice cream makers, mixers
etc.).
• Before cleaning the appliance, always switch off
the appliance and unplug it, or pull the house fuse
or switch off the circuit breaker.
• When unplugging always pull the plug from the
mains socket, do not pull on the cable.
In case of malfunction
• If the a malfunction occurs on the appliance,
please look first in the "What to do if ..." section of
these instructions. I f the information given there
does not help, please do not perform any f urther
repairs yourself.
• Refrigerators may only be repaired by qualified
service engineers. Improper repairs can give rise
to significant hazards. If your appliance needs
repairing, please contact your specialist dealer or
our Customer Service.
20
Page 5
Disposal
Appliance Packaging Information
All materials are environmentally sound! They can be
dumped or burned at an incinerating plant without
danger!
About the materials: The plastics can be recycled and
are identified as follows:
>PE< for polyethylene, e.g. the outer covering and
the bags in the interior.
Disposal of old Appliances
For environmental reasons, refrigeration appliances
must be disposed of properly. This applies to your old
appliance, and - at the end of its service life - for your
new appliance as well.
1
Warning! Before disposing of old appliances make them inoperable. Remove plug
from mains, sever the power cable, remove
or destroy any snap or latch closures. This
eliminates the danger that playing children
lock themselves into the appliance (danger of
suffocation!) or place themselves into other
life-endangering situations.
>PS< for polystyrene foam, e.g. t he pads, which are
all free of chlorofluorocarbon.
The carton parts are made from recycled paper and
should be disposed of at a waste-paper recycling collection location.
Disposal:
• The appliance may not be disposed of with
domestic waste or bulky refuse.
• The refrigerant circuit, especially the heat
exchanger at the back of the appliance, may not
be damaged.
• Information concerning collection schedules or
locations can be obtained from the local disposal
authorities or town hall.
Remove transport safeguard
The appliance and the interior fittings are protected
for transport.
3. Remove all adhesive tape and packing pieces
from the interior of the appliance.
3
You can remove any remnants of adhesive
using white spirit.
21
Page 6
Installation
Installation Location
The appliance should be set up in a well ventilated,
dry room.
Energy use is affected by the ambient temperature.
The appliance should therefore
– not be exposed to direct sunlight;
– not be installed next to radiators, cookers or
other sources of heat;
– only be installed at a location whose ambient
temperature corresponds to the climate classi-
fication, for which the appliance is designed.
The climate classification can be found on the serial
plate, which is located at the left on the inside of the
appliance.
The following tableshows which ambient temperature
is correct for each climate classification:
If installation next to a source of heat is unavoidable,
the following minimum clearances must be maintained at the sides of the appliance:
– for electric cookers 3 cm;
– for oil and coal fired ranges 30 cm.
If these clearances cannot be maintained a heat insulating pad is required between the cooker and the
refrigeration appliance.
If the refrigeration appliance is installed next to
another refrigerator or freezer a clearance of 5 cm at
the sides is required, in order to prevent the formation
of condensation on the outside of the appliance.
Climate
classification
SN +10to+32°C
N+16to+32°C
ST +18to+38°C
T+18to+43°C
for an ambient
temperature of
Your refrigerator needs ventilation
The integrated door of the furniture cabinet largely
seals the installation recess. i-appliances must therefore be provided with ventilation by having an opening
in the f urniture plinth. The warmed air must be able to
be exhausted upwards through the air shaft on the
furniture back. The ventilation cross-sections should
be at least 200 cm
Important note! In order not to impair the function of
the applia nce, never cover or obstruct the ventilation
openings.
2
.
Installation
See chapter „Installation Instructions“.
Please check whether, after installing your appliance
and especially after rehingeing the door, the door
seal seals right round. An untight door seal may lead
to heavy frosting and thereby to a higher power consumption (see also „What to do if...“).
min. 200 cm
min. 200 cm
2
50
50
2
22
Page 7
Electrical connection
Before initial start-up, refer to the appliance serial
plate to ascertain if supply voltage and current values
correspond with those of the mains at the installation
location.
e.g.: AC 220 ... 240 V 50 Hz or
220 ... 240 V ~50 Hz
(i.e. 220 to 240 volts alternating current, 50 Hertz)
The rating plate is inside the appliance on the left.
A correctly installed, earthed socket is required for
the electrical supply. The supply must have a fuse ratingofatleast10Amps.
Appliance Description
View of Appliance
(various models)
If the socket is not accessible once the appliance is
built i n, the electrical installation must include suitable
means of isolating the appliance from the mains (e.g.
fuse, cut-out, current trip or similar with a minimum
contact separation of 3 mm).
Attention: The mains connection cable may only be
replaced by a skilled electrician. Please contact your
dealer or our customer service department for
repairs.
Temperature regulator and
interior lighting
Butter and cheese compartment with lid
Variable door storage compartment
Door storage compartment
Bottle compartment
Prior to Initial Start–Up
1. Please clean the appliance interior and all acces-
sories prior to initial start-up (see section: “Cleaning and Maintenance”).
Fruit and vegetable trays
Shelves
General purpose box (not on all models)
Bottle / Can holder (not on all models)
Rating plate
23
Page 8
Starting up - Setting the temperature
The temperature regulator is in the refrigerator compartment on the upper right. It is also the ON/OFFswitch.
3
Position "0" = Refrigeration off
Position "1" = Warmest interior temperature
Position "6" = Coldest interior temperature
1. Plug the mains plug into the mains socket.
2. Set the required temperature by t urning the tem-
perature regulator. The interior lighting comes on.
The compressor starts and then runs automatically.
3. If you want a higher or lower temperature, turn the
temperature regulator to a warmer or cooler setting respectively.
Note: When the setting is changed, the compressor
does not start immediately if automatic defrosting is
currently taking place.
3
3
The following effects are of significance in respect of
the interior temperature:
Goods to be refrigerated can be loaded
immediately after switching on, because the
storage temperature in the refrigerator is
quickly reached.
Note: From a food science point of view,
+5 °C should be considered cold enough as
a storage temperature.
– Ambient temperature;
– Quantity and temperature of the food stored;
– Frequency with which the door is opened and
how long it is left open
– A defect in the appliance.
The temperature regulator setting may therefore
need to be adjusted to suit the specific conditions.
Recommendet settings:
Examples:
Ambient
Temperature
Approx. 10 °C1to2
Approx. 16 °C1to2
Approx. 25 °C2to3
Approx. 32 °C1to2
Approx. 38 °C1to2
Note: At the setting given under „recommendet set-
tings“ the fridge has an average temperature of
approx. +5 °C. These figures apply at ambient temperatures from +10 °Cto+38°C.
Important!
High ambient temperatures (e.g. on hot summer
days) and a cold setting on the temperature regulator
(position "5" to "6") can cause the compressor to run
continuously.
Reason: when the ambient temperature is high, the
compressor must run continuously to maintain the
low temperature in the appliance. The fridge will not
be able to defrost since automatic defrosting of the
fridge is only possible when the compressor is not
running (see also "Defrosting" section). The result is
the build up of a thick layer of frost on the fridge rear
wall.
If this happens, turn the temperature regulator back
to a warmer setting (position "4" to "5"). At this setting
the compressor will be switched on and off as usual
and automatic defrosting recommenced.
Temperature Controller
Position
Switching off the appliance
1. To switch off the appliance, turn the temperature
regulator to position "0". The inside light goes out.
If the appliance is not going to be used
for an extended period:
1. Switch off the appliance by turning the tempera-
ture regulator to position "0". The inside light goes
out.
24
2. Remove the mains plug or switch off or turn out
the circuit breaker or fuse.
3. Clean thoroughly (see section: “Cleaning and
Maintenance”).
4. Leave the door open to avoid the build up of
odours.
Page 9
Interior Accessories
Storage Shelves
Your appliance is equipped with glass storage
shelves.
1. The glass storage shelf above the fruit and vegetable trays must always remain in this position, so
that fruits and vegetable remain fresh longer.
The remaining storage shelves can be adjusted to
various heights:
1. Pull the storage shelf forward until it can be tipped
up or down and removed.
2. To insert at a different height use the same procedure in reverse.
Adjustment for tall goods:
1. Remove the front half of the two-part vario glass
storage shelf and insert it at a different level.
Space is thus gained for storage of tall goo ds on
the underlying storage shelf.
Bottle/can shelf
(not included with all models)
Some models are fitted with a bottle/can shelf.
1. To insert or move the bottle/can shelf, pull out the
corresponding storage shelf.
Ensure that the bottle or cans do not touch the rear
wall of the appliance or, when the door is closed, the
door shelf.
Always lay bottles in the shelf with the top to the front.
Small bottles and cans can be placed crossways in
the holder.
Attention ! Place only unopened bottles or cans horizontally.
Variable Inner Door
The door compartments can be pulled up and
removed, and inserted at other positions as needed.
25
Page 10
Variable door storage compartment
Your model is equipped with a variable door storage
compartment which is fitted under a door storage
compartment and can be slid sideways.
The variable door storage compar tment can be
inserted under every door storage compartment.
1. To change, lift the door storage compartment with
the variable door storage compa rtment upwards
and out of the holders in the door and remove the
retaining bracket out of the guide under the door
storage compartment.
2. Please do the same in reverse to insert the shelf
at a different height.
Correct Storage
For physical reasons, there are different temperature
regions in the fridge. The coldest region is on the lowest storage shelf.Warmer regions are the top storage
shelf, the vegetable basket and the storage compartments on the do or. The arrangement example shows
at which places in the refrigerator suitable temperatures for various types of foods exist.
Tip: Food in the fridge should always be covered or
packaged, to prevent drying and tainting of other
food.
The following are suited for packaging:
– Polyethylene airtight bags and wraps;
– Plastic containers with lids;
– Special plastic covers with elastic;
– aluminium foil.
Defrosting
The fridge defrosts automatically
The rear wall of the fridge covers with frost when the
compressor is running, and defrosts when the compressor is off.
The water from the thawing frost is collected in the
drain channel on the rear of the fridge, feed through
the drain hole into the collector on the compressor,
and then evaporated.
The condensation water drain hole must be cleaned
regularly (see the section "Cleaning and Maintenance".
26
Page 11
Cleaning and Maintenance
For hygienic reasons the appliance interior, including
interior accessories, should be cleaned regularly.
1
• The appliance may not be connected to the mains
• Never clean the appliance with a steam cleaner.
• Do not use defrosting sprays, they can be hazard-
• The appliance must be dry before it is placed back
Warning!
during cleaning. Danger of electrical shock!
Before cleaning switch the appliance off and
remove the plug from the mains, or switch off or
turn out the circuit breaker or fuse.
Moisture could accumulate in electrical components, danger of electrical shock! Hot vapours can
lead to the damage of plastic parts.
ous to your health and/or contain substances that
damage plastics.
into service.
Attention!
• Ethereal oils and organic solvents can attack plastic parts, e.g.
– lemon juice or the juice from orange peals;
– butyric acid;
– cleansers which contain acetic acid.
Do not allow such substances to come into
contact with appliance parts.
• Do not use any abrasive cleansers.
1. Remove the food from the refrigerator.Store it in a
cool place, well covered.
2. Switch the appliance off and remove the plug from
the mains, or switch off or turn out the circuit
breaker or fuse.
3. Removefrostfromtimetotimewithasoftplastic
scraper, e.g. a pastry scraper. Under no circumstances use hard or pointed objects to remove
frost.
4. Clean the appliance and the interior accessories
with a cloth and lukewarm water. Commercially
available dish washing detergents may also be
used.
5. After cleaning wipe with fresh water and rub dry.
6. Check the water drain hole on the rear wall of the
fridge. Clear a blocked drain hole with the aid of
the green strip inserted into the drain hole.
2 Energy Saving Tips
• Do not install the appliance near cookers, radiators or other sources of warmth. High ambient
temperatures cause longer, more frequent operation of the compressor.
• Ensure sufficient air circulation and exhaust at the
appliance base and at the back wall of the appliance. Never cover air vent openings.
7. After everything is dry place appliance back into
service.
• Do not place warm foods into the appliance. Allow
warm foods to cool first.
• Only leave door open as long as necessary.
• Do not set temperature any colder than neces-
sary.
27
Page 12
What to do if ...
Correcting Malfunctions
A malfunction may be caused by only a minor fault
that you can rectify yourself using the following
instructions. Do not perform any other work on the
appliance if the followinginformation does not provide
assistance in your specific case.
Malfunction Possible Cause Remedy
Appliance is not switched on. Switch on the appliance.
Mains plug is not plugged in or is
Appliance does not work.
Appliance cools too much. Temperature is set too cold.
The food is too warm.
loose.
Fuse has blown or is defective. Check fuse, replace if necessary.
Socket is defective.
Temperature is not properly adjusted.
Door was open for an extended
period.
A large quantity of warm food was
placed in the appliance within the last
24 hours.
1
Warning! Repairs to refrigerators/freezers
may only be performed by qualified service
engineers. Improper repairs can give rise to
significant hazards for the user. If your appliance needs repairing, please contact your
specialist dealer or our Customer Service.
Insert mains plug.
Mains malfunctions are to be corrected by an electrician.
Tur n the temperature regulator to a
warmer setting temporarily.
Please look in the "Starting up - Setting the temperature" section.
Open the door only as long as necessary.
Tur n the temperature regulator to a
colder setting temporarily.
The appliance is near a heat source.
Interior lighting does not work. Light bulb is defective.
Heavy build up of frost, possibly also on the door seal.
The compressor does not start
immediately after changing the
temperature setting.
Water on the floor or on storage shelves.
Door seal is not air tight(possibly after
changing over the hinges).
This is normal, no error has occurred.
Water drain hole is blocked.
Please look in the "Installation Location" section.
Please look in the "Changing the Light
Bulb" section.
Carefully warm the leaking sectionsof
the door seal with a hair dryer (not
hotter than approx. 50 °C).Atthe
same time shape the warmed door
seal by hand such that it sits correctly.
The compressor starts after a period
of time.
See the "Cleaning and Maintenance"
section.
28
Page 13
Changing the light bulb
1
Light bulb data: 220-240 V, max. 15 W, fitting: E 14
1. To switch off the appliance, turn the temperature
2. Unplug the mains plug.
3. To change the light bulb, undo the cross head
4. Change the defective light bulb.
5. Refit the light bulb cover and the cross head
Warning! There is a risk of electric shocks!
Before changing the light bulb, switch off the
appliance and unplug it, or pull the fuse or
the circuit breaker.
regulator to position "0".
screw and remove the light bulb cover.
screw.
Noises during Operation
The following noises are characteristic of refrigeration
appliances:
• Clicks
Whenever the compressor switches on or off, a
click can be heard.
• Humming
As soon as the compressor is in operation, you
can hear it humming.
• Bubbling/Splashing
3
When refrigerant flows into thin tubes, you can
hear bubbling or splashing noises. Even after the
compressor has been switched off, this noise can
be heard for a short time.
Regulations, Standards, Guidelines
This appliance was designed for household use and
was manufactured in accordance with the appropriate
standards. The necessary measures in accordance
with appliance safety legislation regulations (GSG),
accident prevention regulations for refrigeration appliances (VBG 20) and the regulations of the German
Society of Electrical Engineers (VDE) were observed
in the manufacture of this appliance.
The refrigerant circuit has been checked for leaks.
;
This appliance is in accordance with the following EU guidelines:
– 73/23/EWG dated 19 February 1973 - low
voltage guidelines.
– 89/336/EWG dated 3 May 1989
(including guideline change notice 92/31/
EWG) - EMV guideline
– 94/2/EG dated 21. 01. 1994 - Directive on
Energy Labelling
– 96/57 EG dated 3. 9. 1996 - Energy Effi-
ciency Requirements of Household Electric Refrigerators, Freezers and
Combinations Thereof.
29
Page 14
Technical Terminology
• Refrigerant
Liquids that can be used to a generate a cooling
effect are known as refrigerants. They have a relatively low boiling-point, indeed so low, that the
warmth from the food stored in the fridge or
freezer can cause the refrigerant to boil and
vaporise.
• Refrigerant Circuit
Closed circulation system that contains the refrigerant. T he refrigerant circuit comprises primarily
of an evaporator, a compressor, a condenser and
pipe work.
• Evaporator
The refrigerant is evaporated in the evaporator.
Similar to all other liquids, refrigerant requires
heat to evaporate. This heat is removed from the
interior of the appliance, as a result the interior is
cooled. The evaporator is therefore located inside
the appliance or placed in foam immediately
behind the inner wall and thus not visible.
• Compressor
The compressor looks like a small drum. It is
driven by a built-in electric motor and is mounted
on the base of the appliance at the rear. The task
of the compressor is to draw in vaporised refrigerant from the evaporator, to compress it, and to
pass it on to the condenser.
• Condenser
The condenser normally has the form of a grid.
The refrigerant compressed in the compressor is
liquefied in the condenser. During this process,
heat is released to the surrounding air at the surface of the condenser. The condenser is mounted
on the base of the appliance.
Customer Service
If you cannot find the remedy for a malfunction in
these operating instructions, please contact your
dealer or our customer service department.
Addresses and telephone numbers are listed in the
accompanying booklet "Guarantee Conditions/Customer Service Locations".
Selective ordering of replacement parts can save
unnecessary travel and costs. For this reason always
provide the following appliance information:
•Model Name
•Model Number (PNC)
•Serial Number (S-No.)
This information can be found on the rating plate in
the interior at the left of the appliance. We recommend that you enter this information here, so that it is
handy if needed.
Note: The customer bears the costs of unjustified
customer service calls even during the guarantee
period.
30
Page 15
Contents
Installation Instructions
Installationpartssupplied...............31
Dimensioneddrawings.................31
Aligning the furniture housing . . . . . . . . . . . . 31
Rehingeing the door (where necessary). . . . 32
Push appliance into place and align. . . . . . . .33
Screwapplianceintoplace...............33
Installcaps...........................33
Appliance door / furniture door connection . .33
Applyjointcoverfillet...................32
Attachtheventilationgrille ..............32
Installation parts supplied Dimensioned drawings
2
200 cm
874-880
50
550 min.
50
560 min.
200 cm
873
2
540
549
Aligning the furniture housing
90°
90°
100
200 cm
1221-1227
2
550 min.
50
560 min.
200 cm
50
2
540
1220
549
31
Page 16
Rehingeing the door (where necessary) models with freezer compartment only
The following installation steps are illustrated
only when the door is hinged on the r ight.
If you want the door hinged on the left, please
carry out the following installation steps on the
opposite side as appropriate.
Apply joint cover fillet Attach the ventilation grille
32
Page 17
Push appliance into place and align Screw appliance into place
2mm
Install caps Appliance door / furniture door connection
b: Furniture doors with frame and filling
a: Smooth furniture doors
33
Page 18
822 941 101 - 1299
Änderungen vorbehalten
Loading...