Page 1
2222748-61
GEBRAUCHSANWEISUNG
OPERATING INSTRUCTION
D
t
JKI 2433
Page 2
15
Contents
t
Instructions for the user
Important Safety Instructions 16
Use 17
Cleaning the interior 17
Starting-up 17
Temperatur control 17
Fresh food refrigeration 17
Inner arrangement 17
Freezing fresh food 18
Storage of frozen food 18
Thawing 19
Ice-cube production 19
Defrosting 19
Maintenance 20
Periodic cleaning 20
Periodic of non-operation 20
Interior light 20
Customer service and
spare parts 20
Instructions for the
installer
Technical specifications 20
Installation 21
Positioning 21
Electrical connection 21
Door reversibility 21
Inner door reversal 21
Instructions for totally built-in appliances 22
Page 3
16
Important Safety Instructions
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is supplied with the appliance in order that the new
owner can be acquainted with the functioning of the appliance and the relevant warnings.
These warnings are provided in the interest of safety. You must read them carefully before installing or
using the appliance.
General Safety
■
This appliance is designed to be operated by
adults. Children should not be allowed to tamper
with the controls or play with the product.
■
It is dangerous to alter the specifications or
modify this product in any way.
■
Before any cleaning or maintenance work is
carried out, be sure to switch off and unplug the
appliance.
■
This appliance is heavy. Care should be taken
when moving it.
■
Ice lollies can cause frost burns if consumed
straight from the appliance.
Service / Repair
■
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
■
This appliance should be serviced by an
authorised Service Centre, and only genuine
spare parts should be used.
■
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
more serious malfunctioning. Refer to your local
Service Centre, and always insist on genuine
spare parts.
Use
■
The domestic refrigerators and freezers are
designed to be used specifically for the storage of
edible foodstuffs only.
■
Frozen food must not be re-frozen once it has
been thawed out.
■
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
■
The inner lining of the appliance consists of
channels through which the refrigerant passes.
If these should be punctured this would damage
the appliance beyond repair and cause food loss.
DO NOT USE SHARP INSTRUMENTS to scrape
off frost or ice. Frost may be removed by using
the scraper provided. Under no circumstances
should solid ice be forced off the liner. Solid ice
should be allowed to thaw when defrosting the
appliance. See defrost instructions.
■
Do not place carbonated or fizzy drinks in the
freezer as it creates pressure on the container,
which may cause it to explode, resulting in
damage to the appliance. Do not use a
mechanical device or any artificial means to
speed up the thawing process other than those
recommended by the manufacturer. Never use
metal objects for cleaning your appliance as it
may get damaged.
Installation
■
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cord is damaged, it must
be raplaced by a special cord or assembly
available from the manufacturer or its service
agent.
■
There are working parts in this product which
heat up. Always ensure that there is adequate
ventilation as a failure to do this will result in
component failure and possible food loss. See
installation instructions.
■
Parts which heat up should not be exposed.
Wherever possible the back of the product should
be against a wall.
■
If the appliance has been transported horizontally,
it is possible that the oil contained in the
compressor flows in the refrigerant circuit. It is
advisable to wait at least two hours before
connecting the appliance to allow the oil to flow
back in the compressor.
Environment Protection
■
This appliance does not contain gasses which
could damage the ozone layer, in either its
refrigerant circuit or insulation materials. The
appliance shall not be discarded together with
the urban refuse and rubbish. Avoid
damaging the cooling unit, especially at the
rear near the heat exchanger. Information on
your local disposal sites may be obtained
from your municipal authorities.
■
The materials used on this appliance marked
with the symbol are recyclable.
Page 4
17
Use
t
Cleaning the interior
Before using the appliance for the first time, wash
the interior and all internal accessories with
lukewarm water and some neutral soap so as to
remove the typical smell of a brand-new product,
then dry thoroughly.
Do not use detergents or abrasive powders, as these
will damage the finish.
Starting-up
Insert the plug into the wall socket.
Open the door and turn the thermostat control knob,
to be found on the upper right hand side of the inner
compartment, clockwise beyond position «O» (OFF)
to start the appliance.
Temperature control
Temperature adjustment is obtained by turning the
thermostat knob clockwise until its pointer coincides
with the required setting.
A medium setting is generally the most suitable.
The minimum setting (least cold) is represented by
the lowest number and the maximum setting
(coldest) by the highest number. In any case, bear in
mind that the temperature can be either increased
(warmer) by turning the thermostat knob
anticlockwise or decreased (colder) by turning it
clockwise.
The thermostat knob setting should be adjusted
depending on the inner temperature of the
refrigerator, which, in turn, depends on a number of
factors, such as: the ambient temperature, the
number of times the door is opened, the quantity of
food stored and the location of the appliance.
Warning
If the ambient temperature is high, the
thermostat knob is on the coldest setting
(higher numbers) and the appliance is
fully loaded, the compressor may run
continuously, causing frost or ice to form
on the evaporator. If this happens, turn
the knob to a warmer setting
(lowernumbers) to allow automatic
defrosting and so a saving in
electricity consumption.
Fresh food refrigeration
To obtain the best performance:
do not store warm food or evaporating liquids in the
refrigerator;
do cover or wrap the food, particularly if it has a
strong flavour.
Position food so that air can circulate freely round it.
Useful hints:
Meat (all types): wrap in polythene bags and place
on the glass shelf above the vegetable drawer.
For safety, store in this way only one or two days
at the most.
Cooked foods, cold dishes, etc..: these should be
covered and may be placed on any shelf.
Fruit and vegetables: these should be thoroughly
cleaned and placed in the special drawer(s)
provided.
Butter and cheese: these should be placed in
special airtight containers or wrapped in aluminium
foil or polythene bags to exclude as much air as
possible.
Milk bottles: these should have a cap and should
be stored in the bottle rack on the door.
Bananas, potatoes, onions and garlic, if not
packed, must not be kept in the refrigerator.
Inner arrangement
Movable shelves
The walls of the refrigerator are equipped with a
series of runners so that the shelves can be
positioned as desired.
D040
Page 5
18
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
To make these adjustments proceed as follows:
Gradually pull the shelf in the direction of the arrows
until it comes free, then reposition as required.
Freezing fresh food
The 4-star compartment ( ) is suitable for
long term storage of commercially frozen food and for
freezing fresh food.
To freeze fresh foods it is not necessary to change
the setting of the thermostat knob.
However, for a quicker freezing operation, turn the
thermostat knob to the coldest setting; but remember
that, in this condition, the refrigerator compartment
temperature might drop below 0°C. If this occurs
reset thermostat knob to a warmer setting.
To help you make the most of the freezing process,
here are some important hints:
■
the maximum quantity of food which can be
frozen in 24 hrs. is shown on the rating plate;
■
the freezing process takes 24 hours. No further
food to be frozen should be added during this
period;
■
only freeze top quality, fresh and thoroughly
cleaned, foodstuffs;
■
prepare food in small portions to enable it to be
rapidly and completely frozen and to make it
possible subsequently to thaw only the quantity
required;
■
wrap up the food in aluminium foil or polythene
and make sure that the packages are airtight;
■
do not allow fresh, unfrozen food to touch food
which is already frozen, thus avoiding a rise in
temperature of the latter;
■
lean foods store better and longer than fatty ones;
salt reduces the storage life of food;
■
water ices, if consumed immediately after removal
from the freezer compartment, can possibly cause
the skin to be freeze burnt;
■
it is advisable to show the freezing-in date on
each individual pack to enable you to keep tab of
the storage time;
■
do not put carbonated liquids (fizzy drinks,
etc.) in the freezing compartment as they may
burst.
Storage of frozen food
When first starting-up or after a period out of use,
before putting the products in the compartment let
the appliance run for at least two hours on the
coldest setting, then turn the thermostat knob to the
normal operating position.
To obtain the best performance from this appliance,
you should:
■
make sure that the commercially frozen foodstuffs
were adequately stored by the retailer;
■
be sure that frozen foodstuffs are transferred from
the foodstore to the freezer in the shortest
possible time;
■
not open the door frequently or leave it open
longer than absolutely necessary.
Once defrosted, food deteriorates rapidly and cannot
be refrozen.
Do not exceed the storage period indicated by the
food manufacturer.
Important
If there is a power failure when food is in
the freezer, do not open the door of the
freezer compartment. The frozen food will
not be affected if the power cut is of short
duration (up to 6 8 hours) and the freezer
compartment is full, otherwise, it is
recommended that the food should be
used within a short time (a temperature
increase of the frozen food shortens its
safe storage period).
PR187
PR190
Page 6
19
t
Thawing
Deep-frozen or frozen food, prior to being used, can
be thawed in the refrigerator compartment or at room
temperature, depending on the time available for this
operation.
Small pieces may even be cooked still frozen, directly
from the freezer: in this case, cooking will take longer.
Ice-cube production
This appliance is equipped with one or more trays for
the production of ice-cubes.
Fill these trays with water, then put them in the
freezer compartment.
Do not use metallic instruments to remove the trays
from the freezer.
Defrosting
Frost is automatically eliminated from the evaporator
of the refrigerator compartment every time the motor
compressor stops, during normal use.
The defrost water drains out through a trough into a
special container at the back of the appliance, over
the motor compressor, where it evaporates.
It is important to periodically clean the defrost
water drain hole in the middle of the refrigerator
compartment channel to prevent the water
overflowing and dripping onto the food inside.
Use the special cleaner provided, which you will
find already inserted into the drain hole.
The freezer compartment, however, will become
progressively covered with frost. This should be
removed with the special plastic scraper provided,
whenever the thickness of the frost exceeds 4 mm.
During this operation it is not necessary to switch off
the power supply or to remove the foodstuffs.
Never use sharp metal tools to scrape off frost
from the evaporator as you could damage it.
Do not use a mechanical device or any artificial
means to speed up the thawing process other than
those recommended by the manufacturer.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried out
as follows:
1. pull out the plug from the wall socket or turn the
thermostat knob to the «O» setting;
2. remove any stored food, wrap it in several layers of
newspaper and put it in a cool place;
3. leave the door open, place a basin on the top shelf
of the refrigerator compartment, under the drain
hole, remove the plug as shown in the figure;
4. when defrosting is completed, dry the interior
thoroughly and refit the plug.
D037
PR151
Keep the scraper for future use; turn the thermostat
knob back to the required setting or replace the plug
in the power socket. After two or three hours, reload
the previously removed food into the compartment.
Important
A temperature rise of the frozen food packs,
during defrosting, may shorten their safe
storage life.
Page 7
Technical specifications
20
Unplug the appliance before carrying out any
maintenance operation.
Periodic cleaning
Never use metal objects for clearing your appliance
as it may get damaged. Clean the inside with warm
water and bicarbonate of soda. Rinse and dry
thoroughly.
Periods of non-operation
When the appliance is not in use for long periods,
take the following precautions:
remove the plug from the wall socket;
remove all food:
defrost and clean the interior and all accessories;
leave the door ajar to allow air to circulate to prevent
unpleasant smells.
Interior light
The light inside the refrigerator compartment is easy
to get at through the opening in the light holder.
If the light does not go on when the door is open,
check that it is screwed into place properly.
If it still does not light up, change the bulb.
The rating is shown on the light bulb cover.
Maintenance
D731
Customer service and spare parts
If a fault occurs, check the following before calling
the Servicing Department:
The light does not come on when you open the
door.
Check that the bulb is powered. If the electricity
supply is OK, replace the bulb.
The compressor does not work.
Check that it is powered. Check that the thermostat
is in operative mode.
The compressor runs continuously.
The thermostat is set too high.
Traces of water on the bottom of the refrigeration
compartment.
Check that the defrosting water discharge hole is not
obstructed.
If your appliance is still not working properly after
making the above checks, contact the nearest
service centre.
To obtain fast service, it is essential that when
you apply for it you specify the model and serial
number of your appliance which can be found on
the guarantee certificate or on the rating plate
located inside the appliance, on the bottom lefthand side.
The technical data is indicated in the rating plate on the left side inside the appliance.
Page 8
Installation
t
21
lf this appliance featuring magnetic door seals is
to replace an older appliance having a spring
lock (latch) on the door or lid, be sure to make
that spring lock unusable before you discard the
old appliance. This will prevent it from becoming
a death-trap for a child.
Positioning
The appliance should be installed well away from
sources of heat such as radiators, boilers, direct
sunlight etc.
Best performance is obtained with ambient
temperature between +18°C and +43°C (class T);
+18°C and +38°C (class ST); +16°C and +32°C
(class N); +10°C and +32°C (class SN).
The class of your appliance is shown on its
rating plate.
For building into kitchen units follow the special
“Building-in” instructions given.
Electrical connection
Before plugging in, ensure that the voltage and
frequency shown on the serial number plate
correspond to your domestic power supply.
Voltage can vary by ±6% of the rated voltage.
For operation with different voltages, a suitably sized
auto-transformer must be used.
Important
The appliance must be earthen.
The power supply cable plug is provided
with a contact for this purpose.
If the domestic power supply socket is not
earthed. connect the appliance to a separate
earth in compliance with current regulations,
consulting a specialist technician.
The Manufacturer declines all responsibility if
the above safety precautions are not observed.
This appliance complies with EEC directive
number, 87/308 of 2/6/87 relative to radio
interference suppression.
This appliance complies with the following
E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and
subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Door reversibility
The appliance’s door have been locked in position
for transport by means of pins on both sides.
According to the door opening direction, remove
relevant pins at the top and at the bottom.
Inner door reversal
1. Using a screwdriver release bracket (1) by
pressing on the internal spring (Fig.) and withdraw
it from its seat together with the door;
2. remove plug (2) and fit it in the hole left open on
the opposite side;
3. turn the door through 180°, remove the bracket (1)
and refit it on the opposite side.
4. Refit the door and insert the top pin and bottom
bracket (1), pushing it into place.
To ensure correct storage of food, the door is fitted
with a simple spring device which holds it in the open
position until it is properly closed.
D163
B
A
1
2
180°
PR140
Page 9
22
Instructions for totally built-in
appliances
Dimensions of the recess
Height 880 mm
Depth 550 mm
Width 560 mm
1. For safety reasons, minimum ventilation must be as
shown in Fig.
Attention: keep ventilation openings clear of
obstruction.
2. Slide the appliance into the recess, pushing it
against the wall on the handle side.
3. If after having carried out the previously described
operation there is still some space between the
appliance and the kitchen unit, fit the trimming
provided together with the appliance on the stop
strip (A).
4. Open the door and push the appliance against the
side of the kitchen unit opposite to that of appliance
hinges.
Fasten the appliance with 4 screws provided in the
kit included with the appliance. Snap vent grille (C)
and hinge cover (D) into position.
Page 10
23
t
5. Press in the joint covers between the appliance and
the kitchen furniture.
6. Apply covers (B) on joint cover lugs and into hinge
holes.
7. Position the runners (A) at the top and bottom of the
inside of the kitchen unit as shown in Fig. and mark
the position of the external holes.
After preparing the holes, screw the runners to the
kitchen unit door using 3.5x16 mm screws.
8. Open both the appliance door and that of the
kitchen unit to approx. 90°. Place the little plates
over the runners. Hold the doors of the appliance
and the unit together and mark the holes.
9. Remove the little plates and make the holes with a
diam. of 2 mm. Replace the little platee over the
runners and screw in the screws provided
(3.5x16 mm).
For the alignment of the kitchen unit door, if
necessary, use the clearance size of the slotted
holes. At the end of the procedure, check that the
doors of the appliance and the kitchen unit open
properly.
D094
20mm
H
8mm
PR34
PR35
Loading...