J-Tech Digital NA-EX01R Operating Instructions Manual

Page 1
Operating Instructions
Website: www.jtechdigital.com Toll Free: 1-888-610-2818[US]
Email: Support@jtechdigital.com
NexAV
TM
HDBaseT 4K@60Hz HDMI
Extender Receiver 70M/40M
NA-6001
Page 2
The HDBaseT HDMI Extender Receiver Control Path has been tested for conformity to safety regulations and requirements, and has been certified for international use. However, like all electronic equipment, the NA-EX01R should be used with care. Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of damage to the unit.
Follow all instructions and warnings marked on this unit.
Do not attempt to service this unit yourself, except where explained in this
manual.
Provide proper ventilation, air circulation, and do not use near water.
Keep objects that might damage the device away and assure that the placement
of this unit is on a stable surface.
Use only the power adapter, power cords, and connection cables designed for
this unit.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power
to the device before cleaning.
SAFETY AND NOTICE
Page 3
INTRODUCTION ....................................................................................................... 1
PACKAGE LIST ......................................................................................................... 1
FEATURES................................................................................................................ 1
PANEL DESCRIPTION ............................................................................................. 2
SYSTEM CONNECTION ........................................................................................... 3
SYSTEM CONNECTION ........................................................................................... 4
SPECIFICATION ....................................................................................................... 5
PANEL DRAWING .................................................................................................... 6
TROUBLESHOOTING & MAINTENANCE ................................................................ 7
TABLE OF CONTENTS
Page 4
The NA-EX01R is a 4K HDBaseT Receiver to receive 1080p/4K HDMI signal over CAT5e/CAT6a cable from HDBaseT Transmitter or Matrix Switcher up to 70m /40m (PoH), and enables IR and RS232 pass-through to control source or display device remotely. It also supports CEC.
1 x NA-EX01R Receiver
2 x Mounting Ears with 4 Screws
4 x Plastic Cushions
1 x RS232 Cable
1 x Power Adaptor (DC 24V, 1.25A)
1 x User Manual
Note: Please contact your distributor immediately if any damage or defect in the components is found.
Support Full HD: Delivers high resolution image (1080p@60Hz@48
b/pixels/3D/4Kx2K).
Maximum transmission distance is 70m for 1080p and 40m for 4Kx2K over single
CAT5e/CAT6a cable.
High Bandwidth: 10.2Gps.
HDTV Compatible, use HDMI 1.4 and HDCP2.2 compliant.
Support CEC/IR/RS232 pass-through.
Support bi-directional PoH function.
Bi-directional RS232/IR control.
Use HDBaseT technology.
LED indicators show work status.
INTRODUCTION
PACKAGE LIST
1
FEATURES
Page 5
No.
Name
Description
LINK LED
HDBT Link status indicator:
OFF: No Link. GREEN: Link successful. Blinking GREEN: Link abnormal.
HDCP LED
HDCP compliant indicator
OFF: No HDMI traffic (no picture). GREEN: Traffic with HDCP. Blinking GREEN: Traffic without HDCP.
Power LED
OFF: No power; RED: DC power present.
RS232
RS232 connector.
IR IN
Connect with 5V IR receiver (with carrier) to collect infrared signal, work with far-end IR OUT port.
IR OUT
Connect with 5V IR emitter to send infrared signal, work with far-end IR IN port.
HDMI OUT
Connect with HDMI display.
HDBT IN
Connect to the HDBT OUT socket on the transmitter via CAT5e/ CAT6a cable.
DC 24V
Connect with power supply (Not necessary if transmitter connects with power adaptor).
1
2
3
4
5
6
7
8
9
PANEL DESCRIPTION
2
Page 6
Usage Precautions
Verify all components and accessories included before installation.
System should be installed in a clean environment with proper temperature and
humidity.
All of the power switches, plugs, sockets and power cords should be insulated
and safe.
All devices should be connected before power on.
RXTX RXTX
Transmitter NA-EX01R Receiver
4K 40m 1080P 70m
Laptop
IR Receiver
Projector Remote
Projector
IR Emitter
HDMI:
RS232:
IR:
HDBaseT:
SYSTEM CONNECTION
3
Page 7
Connection Procedure
Step1. Connect HDMI source (such as Blue-ray DVD) to HDMI IN port of
transmitter with HDMI cable.
Step2. Connect HDBT OUT port of transmitter and HDBT IN port of receiver, with
single CAT5e/CAT6a cable.
Step3. Connect HDMI displayer (such as HDTV) to HDMI OUT port of receiver with
HDMI cable.
Step4. Both transmitter and receiver have IR IN and OUT. When one end is used
as an IR receiver, the signal sent from the end can only be transmitted via
the other end.
For example: When “IR IN” of transmitter connects with an IR receiver, the
IR emitter must connect to IR OUT of Receiver.
Step5. Connect the RS232 port of the devices to be controlled and the receiver or
the transmitter.
Step6. Connect with DC24V power adaptor(s) One is enough if Transmitter or
Receiver is connected with adapter as its PoH function).
SYSTEM CONNECTION
4
Page 8
Input & Output
Input
(1) IR; (1) HDBaseT; (1) RS232
Input Connector
(1) 3.5mm mini jack; (1) RJ-45;
(1) 3-pin pluggable terminal block
Audio
Digital audio, transmit through HDMI audio
Output
(1) HDMI; (1) IR; (1) RS232
Output Connector
(1) Female HDMI; (1) 3.5mm mini jack;
(1) 3-pin pluggable terminal block
General
Resolution Range
640x480@60Hz~4K@60Hz 4:2:0
Transmission Mode
HDBaseT
Transmission Distance
1080p ≤ 70m; 4Kx2K ≤ 40m
Bandwidth
10.2Gbps
HDMI Standard
Support HDMI1.4 and HDCP2.2
Operation Temperature
0 ~ +40
Storage Temperature
-10 ~ +55
Relative Humidity
10% ~ 90%
Power Supply
Input: 100VAC~240VAC, 50/60Hz;
Output: DC 24V, 1.25A
Max Power Consumption
14W
Dimension (W*H*D)
115mmx16.2mm x109mm
Net Weight
196g
5
SPECIFICATION
Page 9
HDCPLINK
RX
RS232 IR IN IR OUT HDMI OUT HDBT IN DC 24V
RXTX
115 mm
109 mm
16.2 mm
PANEL DRAWING
6
Page 10
No image on display:
Ensure that the display device has been set to the correct input. Ensure that the HDMI cables used for both the source/transmitter and the
receiver/display are properly connected and are working. Test the HDMI cables
directly from a source to display and ensure their operation.
Ensure that the CAT5e/CAT6a cable has not been damaged and that it has
been terminated correctly with T568B on both ends. A temporary length of
CAT5e/Cat6 can be used for testing to ensure that the devices are all
compatible and working properly.
Ensure proper grounding of the power supply. Known issues with HDMI 1.2 source devices: Older compatibility (HDMI 1.2) may result in HDBaseT transmission issues.
Please contact Technical Support of your director for a solution to these issues.
Color lose or poor picture quality:
Ensure that the HDMI cables used for both the source and transmitter and the
receiver and display are properly connected and are of good quality. Test the
HDMI cables directly from a source to display and ensure their picture quality.
Ensure proper grounding of the power supply. If the static becomes stronger or picture quality becomes worse when
connecting the video connectors, this may be due to improper grounding.
Check the grounding and make sure all the components are properly grounded
to a common ground. Improper grounding may cause damage to the receiver.
If your problem still remaining after following the above troubleshooting steps, please find further assistance.
TROUBLESHOOTING & MAINTENANCE
7
Page 11
Page 12
Product pictures are for reference only. Specifications described herein are subject to change without prior notification. All trademarks are the sole property of their respective companies. Copyright © J-Tech Digital, Inc. All rights reserved.
Loading...