JSW Pacific CCD 602S Users manual

User's Manual

Model No.: 0534

2.4 GHz Wireless Weatherproof

Monitoring System with Dual Mode

(USB & A/V) Receiver

- Wireless Color Weatherproof Camera(CCD-602S)

- Wireless Stylish Dual Mode (USB & A/V)(CCD-680DR)

PLEASE READ CAREFULLY AND SAVE

This manual contains important information about this product's operation.

If you are installing this product for others, you must leave this manual -or a

copy- with the end user.

Important!

Please read this user manual carefully

before installing or using these units.

WARNING- These units should ONLY be disassembled

by an authorized technician if service is required.

Safety Precautions

For correct and safe operation of this system, it is

essential that installers, end-users and service

technicians should follow all safety procedures outlined

in this manual. Specific Warning and Caution statements

(and/or symbols) are marked on the units where needed.

Warning and Caution Statements

"WARNING" indicates a situation where failure to

follow proper procedures can cause personal injury.

"CAUTION" indicates a situation where failure to follow proper procedures can cause damage to the

equipment.

This camera is subject to interference from cordless phones, microwaves, and other wireless devices operating in the 2.4GHz range. Keep the system AT LEAST 10 ft away from the devices during installation and operation.

Model No.: 0534

Contents

Safety and Hazard Notices ---1 FCC/CE WARNING-----------3 Parts Included in This System-----3 Installing the Camera--------4 Installing the Receiver--------5 System Requirements--------5 System Installation--------6 Software installation--------7 Device Setting / Video Device--------10 About Alarm / Alarm Actions--------1 1 Record location / Email--------12 Telephone / alarm Schedule--------13 Motion Detection--------14 Record Schedule--------15 Remote Options--------16 System Options--------17 Technical Data----20 Troubleshooting--------21 Disposal--------21

Safety and Hazard Notices

Damages caused by non-compliance with this operating manual lead to the expiration of the warranty! We will not assume any liability for subsequent damages! We will not assume any liability for damages to items or persons caused by improper handling or non-compliance with the safety notices! Any warranty claim will be null and void in such cases.

- This product has left the factory in perfectly safety condition. In order to maintain

this status and ensure safety operation, the user has to observe the safety notices and warnings ("Attention!" and "Notice!") contained in this operating manual.

The following symbols need to be observed:

= An exclamation mark in a triangle indicates important notices in these

operating instructions that must be observed under all circumstances.

= A lightning symbol warns of electric shock or the impairment of the

appliance's electric safety.

- Make sure that all electric connections and connection cables between the devices of the camera system as well as the devices to be connected meet the pertaining regulations and are in conformity with the operating instructions.

- In commercial institutions, make sure you observe the accidental prevention regulations of the commercial trade organization for electric installations.

- In schools, training facilities, hobby and self-help workshops, qualified personnel needs to supervise the operation of electronic devices.

- Also observe the safety notices and operating instructions of the other appliances connected to the system.

- Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.

- Do not operate the devices unsupervised.

- When opening the covers or removing parts except where possible by hand, you

may expose live parts. Connections may also be live. Prior to aligning, cleaning, service or repair work or exchanging parts or modules, you must separate the appliances from all power sources if you need to open them.

Only an expert familiar with the risks and the pertinent regulations may repair or

maintain an open live appliance.

- Never plug-in or unplug the power jack with wet hands.

- Never tug on the power cords of the power jack, use the plug to unplug it from the socket.

- Make sure that the power cables do not get squashed or damaged by sharp edges

when installing the devices.

- Never replace damaged power cables yourself! In such a case, remove them from the net and take the devices to a workshop.

FCC/CE NOTICE

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacture's instructions, may cause interference to radio and television reception. It has been tested and found to comply with limits for a Class B digital device in accordance with Part 15 of FCC Rules and CE I-ETS 300 440, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television recept i on , whi ch can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient the TV/radio antenna.

2. Relocate the Receiver away from the TV/radio receiver.

3. Plug the Receiver into a different wall outlet so that the Receiver is on a different branch circuit.

4. If necessary, the user should consult the dealer or an experienced radio/television technician

The user may find the following booklet prepared by the Federal Communication Commission helpful: "How to Identify and Resolve TV Interference Problems." This booklet is available from the US Government Printing Office, W ashington, D.C. 20402, Stock No. 004-000-00345-4.

FCC/CE NOTICE

The user is cautioned that changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed. The radios are required to comply with FCC Rules and Regulations as Part 15 devices and CE I-ETS 300 440. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or near their operating frequencies. Changes or modifications to the device may void FCC and CE compliance. Infrequently used radio links should be tested regularly to protect against undetected interference or fault.

Parts Included in This System

1. 2.4 GHz Wireless color camera

2. 2.4 GHz Wireless dual mode receiver

3. Camera Stand

4. 7.5V AC/DC Adaptor for the camera

5. 7.5V AC/DC Adaptor for the dual mode receiver

6. A/V Cable

Installing the Camera

ATTENTION! Prior to drilling and inserting the screws, make sure that

there are no electric cables pipes, etc. in the wall that may become damaged.

1. Rain protection cover

2. In the dark, the integrated infrared lighting is switched on automatically

3. Mounting bracket

4. DC Power

Installing and Connecting the Devices

Select a suitable installation site from which you want to monitor the desired object. A suitable installation site has the following features:

- Dry

- good air circulation

- as dust-free as possible

- with a power outlet in close vicinity

- little vibrations

Select an installation site that is not screened o f by reinforced concrete walls, mirrors, metal shelves, etc. There should not be any appliances with strong electric elds close to the sender or the receiver Any strong electric environment could cause the interference and reduce the performance.

Fastening the wall bracket

- Look for a suitable place for mounting

(possibly with a socket)

- Screw the wall bracket with the supplied

screws to a suitable wall or a suitable platform use dowels if relevant.

- Align the camera and screw the T - bolt tight.

Connecting the camera

Connect the DC plug of the power unit to the voltage supply jack of the camera. Pay attention to the correct input voltage of 7.5V DC!

- Insert the plug-in power unit into a suitable mains socket.

- The camera is now ready for use.

Installing the Receiver

Set up the receiver approx. 1 m above ground (better receiving conditions). There must be a power outlet proximity to the receiving site.

A TTENTION! Only place the receiver on rugged and stable surfaces.

1. Receiver antenna

2. Power plug

3. A/V Output

4. LED (RED for Channel1,2,3,4, BLUE for USB connection)

5. Channel selection switch

6. USB connector

7. Power supply

8. A/V cable

Connecting the receiver to monitor

● Connect the A/V cable as depicted to a suitable monitor or TV system with an A/V cinch input and the receiver (white plug = audio (tone in mono), yellow plug = video).

● Connect the power supply

+ 16 hidden pages