JRC NSVS981 User Manual

NSVS981 Apr. 2005

Application

Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.

Maximum Rating: (Table 2)

Mechanical Specifications: (Fig.2)
Package is designed as small as 3.2x2.5x1.1[mm

Notice:

This part is electrostatic discharge sensitive and may be damaged by improper handling.

693.483MHz Data Communications

Table 1. Electrical Specifications (at Room Temperature)
Item Spec. Typ.
Nominal Center Frequency (f0) 693.379~693.587MHz 693.483MHz
Insertion Loss at f0 4.0dB max. 2.5dB
Loaded Q - 1150
Attenuation f0±2MHz 20dB 25dB
Insertion Phase 693.483MHz - Reference(*1)
Turnover Temperature 32~52ºC 42ºC
Phase Slope - 0.32deg/kHz
Frequency Temperature Coefficient - -0.045ppm/ºC2
Substrate Material - Quartz

Table 2. Maximum Ratings
Item Rating
Maximum Input Power 10dBm
Operating Temperature Range -30~+85ºC
Storage Temperature -30~+85ºC

http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)

JRC SAW FILTER

NSVS981

*1: Nominal Phase = 0ºType

3

] for SMD (Surface Mount Device) type.

Communications Equipment Division

Communications Equipment Marketing Department

10-1, Nishi-Shinjuku 6-chome, Shinjuku-ku,

Tokyo, 160-8328 Japan

Tel. [phone]

Fax. [phone]

http://www.jrc.co.jp/eng/product/saw/index.html(English)

NSVS981 Apr. 2005

Ω

IN
50Ω

SAW

6

12

45

3

OUT
50

(b)

Fig.1 Measuring circuit

3. 2±0. 1

2. 5±0. 1

33

KM

(2)

(a)

(1)

1. 1±0. 1

(1.35)

[4x]

1

2

(0.6)

(0.8)

[2x]

6

[2x]

3

[4x]

(0.55)

5

Fig.2 Package dimensions (in mm)

1.75

4

4.0

1.75

Marking
(1) Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(2) Part number Mark

Pin no. Connection

1 GND
2 IN/OUT
3 GND
4 GND
5 OUT/IN
6 GND

0.95

1.2

3.3

0.6

0.95

Fig.3 Desirable land area (in mm)

NSVS981 Apr. 2005

Notice

1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than –30ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.

2. When soldering iron is used, solder with the temperature at the tip of
soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power
of soldering iron: 30W max..

3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.

4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature
of this component goes down to room temperature.

5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.

6. As it might be a cause of degradation of destruction to apply static electricity
to this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.

Note

1. This specification specifies the quality of this component as a single unit.
Make sure that this component is evaluated and confirmed against this
specification when it is mounted to your products.

2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with
the design of equipment incorporating this product.

3. The products are designed to be used with ordinary electronic equipment
(data and communications equipment, office equipment, audio-video
equipment, measuring instruments, etc). Japan Radio Company does not
assume any liability for the case using the products with the application
required high reliability or safety extremely (such as space equipment,
sea-bottom equipment, medical equipment etc). When intending to use any
our product please contact our sales representatives in advance.

NSVS981 Apr. 2005

Fig.1 Measuring circuit

(R0.3)

[4

×]

(1.4)

(0.8 )

[12×]

Pin No. Connection

1GND(PKG)
2GND(PKG)
3 GND(PKG)
4GND(PKG)
5OUT/IN
6 GND(signal)
7GND(PKG)
8GND(PKG)

9GND(PKG)
10 GND(PKG )
11 IN/OUT
12 GND(signal)

(b)

(3)

Marking
(1) Manufacture's Mark
(2) Lot Number

(a) Year
(b) Month

*Oct.--- X

Nov.--- Y
Dec.--- Z

(c) Da te

1-9 --- 0
10 -19--- 1
20 -31--- 2

(3) Part Number Mark

(1.26± 0.1 3)

[12× ]

[12× ]

(2.5 4 )

(R0.3)

(2)

4

5

6

7

8

910

(C)

１２３４

10

９８７

11

12

６

５

OUT

50O

SAW

*27nH

*27nH

39pF

33pF

*murata LQW 18Aseries

0

FREQUENCY CHARACTERISTICS

0

Insertion Loss [dB]

Insertion Loss [dB]

20

40

60

80

100

CH1: Center 693.483 Span: 10
CH2: Center 693.483 Span: 10

0

2

4

6

8

10

CH1: Center 693.483 Span: 1
CH1: Center 693.483 Span: 1

S11 S22

2

4

6

8

Insertion Loss [dB]

10

180

90

0

-90

Phase [deg]

-180

Japan Radio Co.,Ltd.