
JRC SAW FILTER
NSVS1114
Application
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
190MHz WCDMA
Table 1. Electrical Specifications
Parameter Spec. Typ.
Input and Output Impedance Nominal Center Frequency (f0) - 190MHz
Pass Bandwidth - 3.84MHz
Insertion Loss 188.08~191.92MHz 16.5dB max. 15.5dB
Response Variation 188.08~191.92MHz 1.0dB max. 0.8dB
Group Delay Variation 188.08~191.92MHz 150ns max. 130ns
Out of Band Rejection 140.0~182.0MHz
182.0~185.0MHz
195.0~198.0MHz
198.0~240.0MHz
(Operating Temperature Range: -10~+75ºC)
40dB min.
35dB min.
35dB min.
40dB min.
48dB
38dB
45dB
46dB
NSVS1114 Jan. 2005
50Ω
Maximum Rating: (Table 2)
Table2. Maximum Ratings
Item Rating
Maximum Input Power +10dBm
Maximum DC Voltage 7.5V
Operating Temperature Range -10~+75ºC
Storage Temperature -20~+85ºC
Mechanical Specifications:
Package is designed as small as 7.0x5.0x1.8[mm
3
] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.jrc.co.jp/jp/product/device/saw/index.html (Japanese)
http://www.jrc.co.jp/eng/product/saw/index .html (English)
Communications and Equipment Division
Communications Equipment Marketing Department
10-1,Nishi-Shinjuku 6-chome Shinjuku-ku,
Tokyo. 160-8328 Japan
Tel. +81 3-3348-3845
Fax. +81 3-3348-3935

NSVS1114 Jan. 2005
IN
50
Ω
*110nH
27pF
876
9
10
123
SAW
*130nH
5
22pF
4
*murata LQW 18A series
OUT
50
Ω
Fig.1 Measuring circuit
(1)
5.0±0.15
1.8 max.
(2)
(a)
J
7.0±0.15
(b)
4Y1
(1.27)
(1.27× 2=2.54)
(c)
(0.9)
(0.8)
(2.54)
(3)
Marking
(1)M a n ufa c ture 's Ma rk
(2)Lot Number
(a) Year
(b) Month
*Oct.--- X
Nov.--- Y
Dec.--- Z
(c) Date
1- 9 --- 0
10 -19--- 1
20 -31--- 2
(3)Part number Mark
No.Connection No. Connection
1 GND(PKG) 6 GND(PKG)
2 GND(PKG) 7 GND(PKG)
3 GND(PKG) 8 GND(PKG)
4
4 GND(signal) 9 GND(signal)
5OUT 10IN
5
(1.27)
(1.27)
10
(1.0)
21
3
(0.6)
[×10]
(1.0)
[×9]
9
(R0.2)
×4]
[
[
(0.3)
×10]
8
7
6
Fig.2 Package dimensions

NSVS1114 Jan. 2005
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -10ºC or more than +75ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact Japan Radio Company before proceeding with
the design of equipment incorporating this product.
3. The products are designed to be used with ordinary electronic equipment (data
and communications equipment, office equipment, audio-video equipment,
measuring instruments, etc). Japan Radio Company does not assume any
liability for the case using the products with the application required high
reliability or safety extremely (such as space equipment, sea-bottom equipment,
medical equipment etc). When intending to use any our product please
contact our sales representatives in advance.

NSVS1114 Jan. 2005
20
40
60
80
Insertion Loss [dB ]
100
1400
FREQUENCY CHARACTERISTICS
0
170 180 190 200 210
Frequency [MHz]
10
12
14
16
18
20
1200
1000
Group Delay [ns]
800
600
S11
186 188 190 192 194
Frequency [MHz]
S22