Johnson Controls T7000 Series, T7601-TF20-***JS0, T7600-TF20-***JS0, T7603-T000-***JF0, T7600-TF21-***JS0 Installation Instructions Manual

T7000 LCD Digital Thermostat

Installation Instructions

T7600-TF21-...JS0, T7601-TF20-...JS0, T7600-TF20-...JS0, T7603-T000-...JF0,
T7600-TB21-...JA0

Refer to the QuickLIT website for the most up-to-date version of this document

Figure 1

Figure 4

1

Figure 2

Figure 3

℃

/

o

F

AUTO

> 50 cm (19.68 inch)

> 150 cm (59.05 inch)

°C

•• Ambient

• Ambiante

• Umgebung

• Ambiente

• Ambiente

• Atmosfeer

• Omgivnin

• Prostředí

• Otoczenia

• Среда

• Omgivelse

MAX MIN MAX MIN

45 °C
113 °F

-0 °C

-32 °F

60 °C
140 °F

-10 °C

-14 °F

MAX 90% RH

MIN 10% RH

MAX 90% RH

MIN 10% RH

室温

ON / OFF

M

TiO2/ESP

Timer
Symbol

ONONOFF

OFF

T7603-T000-...JF0

T7600-TB21-…JA0

Application VAL

Floor heater Floor heater water valve

Application AO AI

2-pipe FCU, AO valve Valve Actuator feedback

GND B AGND NTC OCC COM

LVAL N

T7601-TF20-...JS0

Application AO1 VAL2 VAL1

2-pipe relay valve

N/A

N/A Valve

4-pipe relay valve Heating Cooling

2-pipe 3-wire relay valve Valve off Valve on

2-pipe relay valve with
TiO2/ESP

TiO2/ESP Valve

2-pipe relay valve with

oor heating

Floor
heating

Valve

Water source heat pump Reversing Compressor

2-pipe AO valve Valve N/A N/A

Notes: F-ON is line voltage relay output, used for enable/
disable ECM fan in some case

FAN AO1

F-ON VAL2 VAL1

GND B AGND NTC OCC COM

L N

T7600-TF21-...JS0

Application AO2 AO1

2-pipe FCU N/A Valve

4-pipe FCU Heating Cooling

AO2GND B AAO1 GND NTC OCC COM

L HI MED LOW N

AIGND B AAO GND NTC OCC COM

L HI MED LOW N

T7600-TF20-...JS0

Application VAL2 VAL1

2-pipe relay valve N/A Valve

4-pipe relay valve Heating Cooling

2-pipe 3-wire relay valve Valve off Valve on

2-pipe relay valve with
TiO2/ESP

TiO2/ESP Valve

2-pipe relay valve with

oor heating

Floor heating Valve

Water source heat pump Reversing Compressor

GND B AGND NTC OCC COM

L HI MEDVAL2VAL1 LOW N

3

T7000

INSTALLATION INSTRUCTIONS FOR THE TECHNICIAN/FITTER

READ THIS INSTRUCTION SHEET AND THE SAFETY WARNING CAREFULLY BEFORE INSTALLING AND
SAVE IT FOR FUTURE USE

REPAIR AND REPLACEMENT

Do not attempt to repair the T7000 thermostat. In case of improperly functioning control, contact the nearest Johnson Controls®
representative, and specify the desired product code number. When con-tacting the supplier for a replacement please state the
type/model number of the control located on the data plate or cover label.

IMPORTANT:

• Use this T7000 thermostat only as an operating control. Where failure of malfunction of the T7000 thermostat could lead to
personal injury or property damage to the controlled equipment or other property, additional precautions must be designed into the
system. Incorporate and maintain other devices such as supervisory or alarm systems or safety or limit controls intended to warn
of, or protect against, failure or malfunction of the T7000 thermostat.

• Do not install this thermostat in condensing, wet, or damp environment. Moisture may cause damage to the thermostat.

• Do not remove PCB from the enclosure cover. Removing the PCB from the enclosure cover voids the product warranty.

• Make all wiring connection in accordance with local, nation, and regional regulations. Do not exceed the T7000 thermostat
electrical ratings.

• Remove LCD plastic cover before use

WARNING:

Disconnect power supply before making electrical connections. Contact with components carrying hazardous voltages can cause
electrical shock and may result in severe personal injury or death.

• Risk of Electrical Shock: Ground the thermostat according to local, national, and regional regulations. Failure to ground the
thermostat may result in electrical shock and severe personal injury and death.

• Risk of Electrical Shock and Property Damage: Insulate and secure each unused wire lead before applying power to the
thermostat. Failure to insulate and secure each unused wire lead may result property damage, electrical shock, and severe
personal injury or death.

Setup and adjustment:

Press and button for 5 seconds at power off mode (only press button for T7603-T000-...JF0), to get in parameter list, press
M button (press

button for T7603-T000-...JF0 ) to switch over setting items and use and button to change parameter

value.

Item

T7600-

TF21-

...JS0

T7601-

TF20­...JS0

T7600-

TF20­...JS0

T7603-

T000­...JF0

T7600-

TB21­...JA0

Parameter Function Default

01 ■ ■ ■ Application

T7601-TF20-...JS0 with EC Motor control

00: 2-pipe relay valve;
01: 4-pipe relay valve;
02: 2-pipe 3-wire relay valve;
03: 2-pipe relay valve with TiO2/ESP;

04: 2-pipe relay valve with oor heating;

05: water source heat pump;
06: 2-pipe AO valve

T7600-TF21-...JS0 Proportional Control

00: 2-pipe AO valve;
01: 4-pipe AO valve

T7600-TF20-...JS0 ON/OFF control

00: 2-pipe relay valve;
01: 4-pipe relay valve;
02: 2-pipe 3-wire relay valve;
03: 2-pipe relay valve with TiO2/ESP;

04: 2-pipe relay valve with oor heating;

05: water source heat pump

00

02 ■ ■ ■ ■ ■ Upper set point limit Setting range 2~40℃ (36~99

o

F) 35

℃

03 ■ ■ ■ ■ ■ Lower set point limit Setting range 0~38℃ (32~95

o

F) 5

℃

04 ■ ■ ■ ■ Cooling set point unoccupied Setting range 22~32℃ (72~90

o

F) 26

℃

05 ■ ■ ■ ■ ■

Heating set point unoccupied Setting range 10~21℃ (50~70

o

F

) 18℃

06 ■ ■ ■ ■ ■

Frost protection 00: on; 01: off 00

07 ■ ■ ■ ■ ■

Frost protection set point Setting range 0~20℃ 5℃

08 ■ ■ ■ ■

Fan mode when set point
reach

00: off 01: low 00

09 ■ ■ ■ ■

Fan mode when unoccupied 00: low speed; 01: set speed 00

10 ■

ECM Min voltage Min voltage below which the fan output is 0%, range 0-10V. (0.5V) 3V