Johnson Controls LB-FMS1655-F01, LB-FMS1655-F11, LB-FMS1655-F04, LB-FMS1655-F10, LB-FMS1655-F12 Installation Manual
...
FMS-1655 Room Pressure Controller (BACnet
®
/ N2 only products)
Installation Manual
LB-FMS1655-F01
LB-FMS1655-F02
LB-FMS1655-F03
LB-FMS1655-F04
LB-FMS1655-F10
LB-FMS1655-F11
LB-FMS1655-F12
LB-FMS1655-F13
Application
These installation instructions guide the installer through the installation of the FMS-1655 Room Pressure Controller.
Please read these instructions thoroughly before beginning installation.
North American Emissions Compliance
United States
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area may cause harmful interference, in which case users will be required to correct the interference
at their own expense.
LB-FMS1655-S01
LB-FMS1655-S02
LB-FMS1655-S03
LB-FMS1655-S04
LB-FMS1655-T01
LB-FMS1655-T02
LB-FMS1655-T03
LB-FMS1655-T04
Code No. LIT-12013117, Rev. A
Issued August 2018
Canada
This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
Installation
NOTICE
Risk of Property Damage.
Ensure that the power source conforms to the requirements of the equipment. Failure to use a correct power source may
result in permanent damage to the equipment.
NOTICE
Risque de dégâts matériels.
S’assurer que la source d’alimentation électrique est conforme aux spécications de l’équipement. L’utilisation d’une source
d’alimentation électrique inappropriée risque d’endommager irrémédiablement l’équipement.
IMPORTANT: The FMS-1655 Room Pressure Controller must be wired to 24 VAC only. Wiring the unit to 110 VAC will cause
serious damange and void the warranty.
Use of the software that is in (or constitutes) this product or access to the cloud or hosted services applicable to this product,
if any, is subject to applicable terms set forth at www.johnsoncontrols.com/techterms. Your use of this product constitutes an
agreement to such terms. If you do not agree to be bound by such terms, you may return the unused product to your place of
purchase.
Central Monitoring Station
The Next Generation in Critical Airow Controls
Room Pressure Controller
JCI CMS-1655
JCI FMS-1655
JCI FMS-1655
Notes
Warning
Failure to follow the wiring diagrams could result in damage to your equipment and could void your warranty.
Under no circumstances should a single transformer be split between actuator and controller. Doing so
will damage the actuator, the transformer, the controller or all units. A single 120/24V 30Va transformer
is required for the controller and a separate 120/24V 20Va transformer is required for the actuator. This
equipment contains electrostatic sensitive components. To prevent possible damage, take precautions to
prevent electrostatic discharge when handling or servicing this equipment by wearing an approved ESD
grounding wrist strap connected to an earth ground source.
Controller
FAST ACTING
ELECTRONIC ACTUATOR
CORRECT
120/24VAC, 30Va Transformer
Supplied by JCI
Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice.
120/24VAC, 20Va Third Party
Transformer
Actuator
CORRECT
CONTROLLER SETTINGS
FMS-1655 Room Pressure Controller Settings
This form should be completed during the initial configuration for each room pressure controller. Be sure to configure the unit
for either Positive, Negative, or both using the Isolation Mode Configuration setup procedure.
Room Name / Number
Unit Model Number and Serial Number (ESN)
Analog Input
Normal Operating Pressure (reading with door closed)
Sensor Input Mode (normal or inverted)
Sensor Input Range (zero-based or offset)
Sensor Pressure Range
Positive Isolation Setpoint
Negative Isolation Setpoint
Neutral Isolation Setpoint
Pressure Deadband
Analog Output
Operating Mode (Direct or PID)
Analog Output Range (zero-based or offset)
Analog Output Upper Limit (0 – 100%)
Analog Output Lower Limit (0 – 100%)
Analog Output Input Channel (AI-1 thru AI-4, TI-1 or TI-2)
Analog Output Action (Direct or Reverse)
Analog Output Range (zero-based or offset)
Door Switch
Operating Mode (normally-open or normally-closed)
Delay Setting (0 - 240 secs)
Relay Output
Trigger Mode (Setpoints, Isolation Mode or Occupancy)
Input Channel (AI-1 thru AI-4, TI-1 or TI-2)
Positive Isolation High Setpoint
Positive Isolation Low Setpoint
Negative Isolation High Setpoint
Negative Isolation Low Setpoint
Relay Acting Mode (Direct or Reverse)
Delay Setting (0 - 180 secs)
PID Constants
Proportional Constant (0.5 – 100.0 %)
Integral Constant (0.0 – 100.0 %)
Derivative Constant (0.0 – 100.0 %)
Alarm Limits
Positive Isolation High Alarm Setpoint
Positive Isolation High Warning Setpoint
Positive Isolation Low Warning Setpoint
CONTROLLER SETTINGS
FMS-1655 Isolation Room Pressure Controller Settings
Positive Isolation Low Alarm Setpoint
Negative Isolation High Alarm Setpoint
Negative Isolation High Warning Setpoint
Negative Isolation Low Warning Setpoint
Negative Isolation Low Alarm Setpoint
Audible Alert
Enabled Input Channels (AI-1 thru AI-4, TI-1, TI-2)
Operating Mode (audible or silent)
Delay Time Base (secs or mins)
Delay Setting (0 – 60)
Alarm Quiet Period Starting Hour (0 – 23)
Alarm Quiet Period Ending Hour (0 – 23)
Engineering Units
Inches of Water or Pascals
Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice.
INSTALLATION MANUAL
Table of Contents
GENERAL
Specifications………………………………………………………………………………...……………………………………………1 - 2
Part Number Guide…………………………………………………………………………………………………………………………2
Overview……………………………………………………………………..…………………….………………………………………3 - 4
MOUNTING/WIRING
FMS-1655 Flush Mount With Internal Sensor
Introduction…………………………………………………………………………………………………………………………………5
Mounting Procedure………………………………………………………………………………………....……………………………5 - 6
Internal Sensor Illustration………………………………………………………………………….....……………………………………7
FMS-1655 With Remote Sensor
Introduction…………………………………………………………………………………………………………………………………9
Mounting Procedure………………………………………....………………………………………………………………………………9
FMS-1655 With Standard Remote Sensor Illustrations………………………………………………………………………....…10 - 11
Remote Sensor Configuration Illustration……………………………………………………………………………………………..12
Analog Output to Electric and Pneumatic Damper Actuator Illustrations (Internal Sensor Model)………………....………13 - 14
Analog Output to Variable Speed Drive Illustration (Internal Sensor Model)………………………………………………..………15
Analog Output to Modulated Air Controller Illustration (Internal Sensor Model)……………………………………………………16
Analog Output to Pneumatic Damper Actuator Illustration (Internal Sensor Model)………………………………………………17
Analog Output to Variable Speed Drive Illustration……………………………………………………………………………………18
Adding Remote Pressure Sensor with 4-20mA Out to Internal Sensor Model Illustration……………………………………19
Analog Input to 2 Remote Pressure Sensor 4-20mA Out Illustration……………………………………………………………… 21
Analog Input to 3 Remote Pressure Sensor 4-20mA Out Illustration……………………………………………………………… 22
Analog Input to 4 Remote Pressure Sensor 4-20mA Out Illustration……………………………………………………………… 23
Analog Input to Temperature Sensor Illustration……………………………………………………………………………………… 24
Custom Sensor Illustration………………………………………........................................................................……………………25
Digital Input to Door Switch Illustration………………………………………………………………………………………………… 26
Digital Input to Occupancy Sensor……………………………………………………………………………………………………28
Relay Output Alarm Illustration………………………….………………………………………………………………………………29
Relay Output to Warning Illustration……………......…………………………………………………………………………………30
Relay Output 1 Illustration…………………........………………………………………………………………………………………31
Relay Output 2 Illustration………………........……....…………………………………………………………………………………32
Power Illustration……………………………...….…………………………………………………………………………………………33
Isolated Power Supply………………………..……………………………………………………………………………………………34
COMMUNICATIONS - BACnet MS/TP
Wiring Illustration………………………………………………………………………………………………………...…………………36
COMMUNICATIONS - METASYS N2 OPEN
Wiring Illustration…………………………………………………………………………………………………....………………………37
FMS-1655 QUICK START GUIDE
Quick Start Guide………………………………………………………………………………………………………....………………38
Main Display Screen………………………………………………………………….....…………………………………………………38
Automated Clean Cycle ………………………………………………………………...……………………………………………38 - 39
Configuring Room Pressure Monitor…………………………………………......………………………………………………………39
Setting Up Analog Output………………………………………………………..………………………………………………………39
Enabling Door Switch………………………………………………………………………………………………………………39 - 40
Setting Up Alarm Relay Output....……………………………………………….………………………………………………………40
Setting Alarm Limits...…………………………………………..…………………………………………………………………………40
Changing Isolation Mode.……………………………………..........……………………………………………………………………40
INSTALLATION MANUAL
Table of Contents
Invoking Auto Clean Cycle.………………………………..........…………………………………………………………......……….....40
Changing Network Settings..………………………….....…………………………………………………………………………………40
Adding Password Security…………………………...……………………………………………………………………………………40
Changing Display Settings……………….……………………………………………………………………………......…………40 - 41
Built-in Diagnostics………………………...………………………………………………………………………………………………41
MODULE SETTINGS
Configuring Display Module Settings……………………………...……………………………………………………………………43
Configuring Main Controller Module Settings………....………………………………………………………………………………44
Configurations and Settings………………………………………………………………………………………………………………45
BACnet® OBJECTS
Analog Input Objects………………………...…….………………………………………………………………………………………46
Analog Output Objects……………………..……...………………………………………………………………………………………46
Binary Input Objects………………………..……..………………………………………………………………………………………46
Binary Output Objects……………………....………..……………………………………………………………………………………46
Analog Value Objects……………………....…………..……………………………………………………………………………46 - 47
Multistate Output Objects……………..………………...…………………………………………………………………………………47
METASYS® N2 OBJECTS
Analog Input Objects…………………………....…………………………………………………………………………………………48
Analog Output Objects……………………….....…………………………………………………………………………………………48
Binary Input Objects……………………………...………………………………………………………………………………………48
Binary Output Objects………………………….....………………………………………………………………………………………48
Internal Float Value Objects………………………..………………………………………………………………………………48 - 49
Multistate Output Objects……………………….....………………………………………………………………………………………49
CLEANING THE DISPLAY
Cleaning the FMS-1655……………………….....………………………………………………………………………………………51
DIAGRAMS
Wiring Illustration……………………………………………………………………......…………………………………………………52
Integrated Flush Mount Wiring Box Dimensions………………....……………………………………………………………………53
Flush Mount Bracket Dimensions………………………………………………………………………………………………………54
Thin Mount Wiring Box Dimensions……………………..………………………………………………………………………………55
FLOW DIAGRAMS
Unit Setup Tree………………………………….....………………………………………………………………………………………57
System Setup Tree……………...……………………………………………………………………………………………………58 - 60
Display Setup Tree…………....……………………………………………………………………………………………………………61
Diagnostics Tree………………..…………………………………………………………………………………………………………62
Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice.Due to continuous improvement, JCI reserves the right to change product specifications without notice. Due to continuous improvement, JCI reserves the right to change product specifications without notice.
GENERAL
Specications
Electrical
Optional External Remote Sensor Distance……………………………………………………………………………………………………Up to 1,000 feet
Optional External Remote Sensor....………………………………………………………………………………Wiring 18-22 AWG, shielded twisted pair
Power Supply..…………………………………………………………………………………………………………………………………24 Vac ±10%, 30Va
Accuracy of Measurement.....……………………………………………………………………………………………………………………………±0.5%FS
Pressure Range (NIST Traceable / Individual certication available as option)…………………………………………………………………±0.2500 “WC
Pressure/Flow……………………………………………………………………………………………………………………………………up to 0.25 ”WC
4 Analog Inputs…………………………………………………………………………………………………………………4-20mAdc, 0-5Vdc or 0-10Vdc
4 Analog Outputs………………………………………………………………………………………………………………4-20mAdc, 0-5Vdc or 0-10Vdc
2 Thermistor Inputs…………………………………………………………………………………………………………NTC Type 2 or 3, 10kΩ @ 25°C
4 Digital Inputs………………………………………………………………………………………………0-5Vdc or 0-24Vdc, Active-High or Active-Low
3 Relay Outputs...………………………………………………………………………………………………………………………………………1A@24Vdc
Control Signal Wire Size............……………………………………………………………………………………………………………………18-22 AWG
Power Supply………………………Class 2, 24Vac ±10%, 30VA universal 120/240 to 24 Vac, 60/50 Hz, step-down isolation transformer provided
Communications
BACnet® MS/TP network....…………………………………………………………………………………………Two-Wire Twisted Pair, RS-485 signaling
Metasys N2 network...………………………………………………………………………………………………Two-Wire Twisted Pair, RS-485 signaling
Recommended Cable Type...……………………………………………………………………………………………………………………… Belden 3107A
Touchscreen User Interface
LCD Size....……………………………………………………………………………………………………………………………………………3.2” diagonal
LCD Type.....……………………………………………………………………………………………………………………………………………Transmissive
Resolution...………………………………………………………………………………………………………………………………………240 x 320 portrait
Viewing Area..……………………………………………………………………………………………………………………………50.60 mm x 66.80 mm
Color Depth.…………………………………………………………………………………………………………………………………18-bit or 262K colors
Backlight Color.....………………………………………………………………………………………………………………………………………………White
Luminous Intensity...………………………………………………………………………………………………………………………………Min 2500 cd/m2
Recommended Cable Type (applicable to surface mount models FMS-1655-s-x only)…………………………………………………… Belden 3125A
Mechanical
FMS-1655 Internal Sensor Flush Mount Housing (Brushed Stainless Steel) Housing..……………………………………………5.6”W x 8.5”H x 1.9”D
FMS-1655 Display Module Housing………………………………………………………………………………………………………3”W x 5”H x 1.13”D
Stainless Steel Cover Plate for Flow Tube……………………………………………………………………………………………2.7”W x 4.5”H x 0.2”D
Stainless Steel Cover Plate for Remote Sensor………………………………………………………………………………………2.7”W x 4.5”H x 0.2”D
FMS-1655 with Flow Tube Cover Plate……………………………………………………………………………………………………………approx. 3.5 lb
FMS-1655 with Optional External Remote Sensor………………………………………………………………………………………………approx. 4.0 lb
FMS-1655 Mounting Options...……………………………………………………………………………………………………………………Surface, Flush
Flow Tube Cover Plate Mounting.. ……………………………………………………………………………………………………………………………Flush
Environmental
Operating Temperature..…………………………………………………………………………………………………………………32° to 125° F Operating
Operating Humidity……………………………………………………………………………………………………………10% - 95% RH, Non-condensing
- 1 -
Due to continuous improvement, JCI reserves the right to change product specifications without notice.
- -
BRAND
LB = Johnson Controls
UNIT
FMS = Flow Monitor Station (FMS)
SERIES
1655 = BACnet / N2 Controller
1655L = LonWorks Controller
1655M = BACnet Monitor
STYLE
S = Surface mount
F = Flush mount
T = Thin mount
INTERNAL SENSOR
0 = No internal sensor
1 = Standard internal sensor
REMOTE SENSOR
0 = No remote sensors
1 = One remote sensor
2 = Two remote sensors
3 = Three remote sensors
4 = Four remote sensors (Not available with LonWorks Controllers)
(BACnet / N2 controllers only)
(Flush mount controller only)
(Not available with LonWorks Controllers)
GENERAL
Specications
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interference that may cause undesired operation.
Please Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a commercial installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee the interference will not occur in a particular installation. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
Caution: To comply with the limits for an FCC Class A computing device, always use the isolated power supply module and recommended interface
cables with this unit.
The Federal Communications Commission warns that changes or modifications to the unit not expressly approved by the part responsible for compliance could
void the user’s authority to operate the equipment.
This Class-A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe-A est conforme à la norme NMB-003 du Canada.
- 2 -
Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice.Due to continuous improvement, JCI reserves the right to change product specifications without notice.
GENERAL
Overview
The JCI FMS-1655 Room Pressure Controller
is an ultra-sensitive instrument used to
monitor and/or control air pressure in hospital
rooms, labs, and clean rooms. This unit
is capable of measuring and displaying
differential air pressures as low as 0.0001
“WC or 0.0249 Pa. The FMS-1655 may be
used to control differential pressures down to
0.0040 ”WC or 1 Pa.
Key features of the FMS-1655 include:
• Full-color touchscreen display with
programmable display options and
adjustable backlight
• Intuitive user interface simplifies setup
and configuration of unit
• Display background changes color to
indicate room status at a glance
• Patented Safety Halo™ with color-coded
180° edge lighting
• Automated clean cycle with fully
programmable duration for quick
turnaround of patient or isolation room
• Audible and visual alarm annunciation
• Internal or remote sensor options
available with up to four sensors total
(one internal, three remotes OR four
remotes)
• Auxiliary universal analog inputs for use
with optional sensors
• Four independent PID control loops for
controlling damper actuators, speed
drives, hot water valves, humidifiers, etc.
• Digital input used to monitor the door
switch of the monitored room
• Relay outputs used for transmitting alarm
condition to remote location
• Dedicated thermistor inputs for
temperature control applications
• Multi-level password protection of
touchscreen user interface
• Zero calibration feature allows in-field
recalibration of zero pressure reading
• Multi-protocol native (BACnet® or
Metasys® N2) for easy integration with
any BMS
• Manual override of analog and relay
outputs assist with test and balance
procedures
• Comprehensive real-time view
• Built-in diagnostics tool
• Easy-to-install backplane/backplate
assembly facilitates permanent
termination of all wiring
The FMS-1655 features enhanced graphics
the patented Safety Halo.™ This simple yet
elegant feature significantly enhances the
alarm status indication of the FMS-1655 by
providing full 180-degree visibility. The Safety
Halo™ is shipped from the factory enabled at
full brightness, but may be dimmed or even
disabled completely from the display setup
menus.
The FMS-1655 is equipped with a 3.2”
diagonal full-color touchscreen display
in portrait orientation (240 x 320). The
password-protected menu tree is very intuitive
and simplifies the setup and configuration of
the unit. The menus incorporate touch-based
interfaces such as sliders, radio buttons, and
dialog popups to facilitate the ease-of-use of
the FMS-1655.
The display implements bright graphical color
changes to indicate the three different alarm
status indications of the monitored isolation
room. These graphical backgrounds indicate
“Normal” when the differential pressure is
within defined limits, “Warning” when the
differential pressure is approaching an
out-of-limits condition, and “Alarm” when the
differential pressure is outside the defined
acceptable and safe limits.
The differential pressure ranges for these
conditions are easily configured by the user
for the specific installation when necessary,
either directly from the touchscreen display or
over the network from the BMS. The graphical
background changes provide an at-a-glance
overview of the monitored isolation room
differential pressure conditions.
Alarm conditions may be defined by the
user, in terms of desired differential pressure
settings for the room being monitored.
When an alarm condition occurs, it may be
annunciated in four user-definable ways:
1) on the display, 2) with an audible alarm,
and 3) transmitted via contacts to a remote
monitoring station and 4) over the BMS
network. The alarm will automatically reset
when the unit has sensed that the room
differential pressure has returned to proper
limits. The attendant may easily mute the
audible alarm by touching the alarm audible
button on the bottom of the display.
For many applications, it is important to have
other variables such as anteroom differential
pressure or relative humidity displayed along
with the isolation room differential pressure.
The FMS-1655 provides for this by means of
three additional universal analog inputs, which
may be configured for either current loop
operation or voltage input operation. Each
input may be scaled as needed to display
correct values, and may have an engineering
units selection associated. The configuration
of each analog input is field selectable
through the use of miniature dipswitches on
the controller unit.
- 3 -
Due to continuous improvement, JCI reserves the right to change product specifications without notice.
GENERAL
Overview
For those applications requiring monitoring
and/or control based on temperature
variances, the FMS-1655 provide two
dedicated thermistor inputs in addition to the
four universal analog inputs. Therefore, a total
of six analog inputs are available for control
applications. The two thermistor inputs may
be used with negative temperature coefficient
(NTC) Type 2 or Type 3 sensors.
The FMS-1655 provides four universal
analog outputs, which may be configured for
either current loop operation or for voltage
operation.
Each analog output may be configured for
proportional operation to provide a linear
signal to the BMS, or for PID (proportionalintegral-derivative) control operation for
closed-loop feedback control of damper
actuators, variable frequency (speed) drives,
hot water valves, humidifiers, or other analogcontrolled devices.
Each universal analog output may be fieldconfigured for the required application using
onboard configuration dipswitches on the
controller module. Each analog output may
also be temporarily overridden using the builtin diagnostic tools for troubleshooting during
the installation and commissioning phase.
The FMS-1655 provides four digital inputs that
may be used for monitoring door switches,
override switches, or other devices with binary
outputs. The configuration and operation of
each input may be configured by the user to
define the effect of a change in its state. Each
digital input may have a programmable delay
duration associated with it. Each digital input
may be configured for either normally-closed
or normally-open operation, and may also
be configured to be active-high or active-low
triggered. The global configuration of the
digital inputs is field selectable through the use
of miniature dipswitches on the controller unit.
The FMS-1655 provides three relay outputs,
which may be configured for either directacting or reverse-acting operation, and may
have a programmable delay associated
to meet the specific needs of the required
application.
A unique feature of the FMS-1655 is its ability
to trigger a relay output based on the current
mode of isolation, thereby providing support
for transfer grilles, supplemental exhaust
dampers, etc. Each relay output may also
be temporarily overridden using the built-in
diagnostic tools for troubleshooting during the
installation and commissioning phase.
The user may set up multiple multi-level
passwords to prevent unauthorized or casual
access to the FMS-1655 configuration
settings. Up to 10 passwords of up to eight
digits may be programmed, with each
having one of four associated access levels.
Administrators and facility management
personnel may have unrestricted access,
while general staff may be assigned restricted
access passwords which limit the functionality
of the user menus.
Room pressure selection of positive, negative,
or neutral isolation may be protected using
limited access passwords, thereby eliminating
the need for keylock switches and keys.
An optional keylock switch may be used to
further control access to change in isolation
modes. In some locales, it is prohibitive to
allow an isolation room controller to switch
between positive and negative modes of
isolation. To accommodate this situation, the
FMS-1655 may be configured at the factory
for either positive- and neutral-isolation modes
only or negative- and neutral-isolation modes.
The FMS-1655 provides native support for
multiple networking protocols, including
BACnet® MS/TP and Metasys® N2 Open.
With multi-protocol native support, the FMS1655 is able to communicate room status
information to the building automation system,
regardless of which protocol is used. (For
applications requiring LonWorks® networking
capability, contact the factory about JCI’s
FMS-1655L series) The configuration of the
desired protocol is field selectable through the
use of miniature dipswitches on the controller
unit.
The FMS-1655 provides a unique set of
built-in diagnostics tools that are extremely
valuable for facilitating the troubleshooting
process during the installation and
commissioning phase.
Included in these built-in diagnostics tools
are manual override capabilities for both
analog outputs and relay outputs, and a
comprehensive real-time view capability that
allows the real-time values and states of each
analog and digital input and output to be
displayed conveniently. This is an extremely
useful tool that facilitates the verification
and certification processes conducted by
typical test and balance personnel during the
commissioning of the system.
There are also options for storing configuration
settings and for restoring those settings, as
well as performing a complete restoration of
the factory default configuration settings.
The FMS-1655 incorporates an innovative
backplane/backplate assembly which greatly
facilitates the installation process and permits
all wiring terminations to be permanent.
The FMS-1655 serves as a direct drop-in
functional replacement for all previous models
of the FMS-1600 series of isolation monitors.
- 4 -
MOUNTING/WIRING
FMS-1655 Flush-Mount with Internal Sensor
Introduction
The FMS-1655 flush-mount model has an
integrated internal sensor and should be
installed outside of the isolation room to be
monitored in the corridor wall. Sensor tubing
should be between this corridor and isolation
room in the most direct and shortest path.
The FMS-1655 is calibrated with configuration
settings programmed at the factory according
to the customer specifications, if provided.
Otherwise, each unit is shipped with factorydefault configuration settings. The user
may change these settings by following the
procedures outlined in the configuration/
programming section of this manual.
The electrical connections to the FMS-1655
are made via convenient terminal block
connectors on the backplane/backplate
assembly as shown on page 7. All wiring
should conform to local regulations and to the
National Electrical Code (NEC). Precautions
must be taken to avoid running sensor wiring
in the same conduit as line voltage or other
conductors that supply highly inductive loads
such as generators, motors, solenoids,
contactors, and other sources of induced
noise. Use 22 AWG or larger for all electrical
wiring terminations.
Following the proper installation of the FMS1655, apply power to the unit and confirm
that you hear a brief chirp at the touchscreen
display, which indicates that the display
module is communicating with the controller
module.
There will be a six second power up delay
during which the Safety HaloTM will cycle
through the following colors: red, green, blue,
yellow, magenta, cyan, and white. After this
power up delay, the unit will display a brief five
second animation of the action icons, followed
by the FMS-1655 splash screen. This
splash screen displays the model number,
electronic serial numbers, firmware version
numbers, protocol selection, and current
network address. The splash screen remains
displayed for about 15 seconds, and then
proceeds to the main differential pressure
screen.
Mounting Procedure
1. Choose a location free of airflow
obstructions, and minimal air turbulence.
The installation should also avoid stagnant
air or “short circuiting” of the supply air to the
exhaust. Typically, the FMS-1655 should be
installed at eye level. It should be mounted
in a location that provides convenient access
such that the display may be viewed with
minimal glare and the touchscreen is easily
accessible to facilitate silencing the unit in the
event of an alarm.
The FMS-1655 is pre-configured at the factory
with the Safety Halo™ status indicator bezel
connected to the internal circuitry on the
display board, and has been tested for proper
operation. The Safety Halo™ should not be
removed from the flush mount faceplate, as it
may damage the internal circuitry and/or the
bezel itself. Attempting to separate the Safety
Halo™ from the flush mount faceplate will
void the manufacturer’s warranty.
2. Before disassembling the flush-mount
electronics assembly, locate the clear
pressure tubing that extends from the lower
corner of the metal backplate to the nipple at
the inside face of the bottom of the faceplate
and disconnect it. The other end of this tubing
should remain attached to the right-angle
barbed fitting at the lower corner of the metal
backplate.
3. Disassemble the flush-mount electronics
assembly by grasping the metal backplate
and pulling it apart from the faceplate.
The metal backplate is attached to the
backplane subassembly which incorporates
all of the wiring termination points.
4. Run the conduit and all wiring according to
local regulations and National Electrical Code.
IMPORTANT: Use the 24 VAC stepdown
isolation transformer, provided with the
unit, to power the FMS-1655; this will
prevent inadvertent ground loop issues and
other problems that might otherwise be
encountered.
5. Pull slack from the tube on the opposite
side of the wall as the backplane/backplate
assembly is moved toward the wall for
mounting. On the opposite side, the return
air stainless base and louvered plate must be
mounted as shown on page 10. Caulk behind
the stainless mounting plate so that there may
be no air flow through the wall. Mount the
backplane/backplate assembly to the wall with
the appropriate screws (and wall anchors if
using the alternate installation method).
- 5 -
Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice.
6. Terminate all electrical connections at the
backplane taking note of the terminal labels.
Note that the power connector is distinguished
as it is of a different color and separated
from the other connectors. The 45-degree
positioned wire openings on the connectors
should greatly facilitate the wire termination
process.
7. On the opposite side of the wall, a length
of pressure tubing will be protruding from
the wall. Cut the tubing as needed to leave
approximately two inches protruding. Press
the tubing onto the barbed fitting of the flow
tube mounting plate (see page 10). Push
the mounting plate and tube toward the
wall, forcing the excess into the wall space.
Fasten the mounting plate to the wall using
appropriate hardware.
MOUNTING/WIRING
SUBHEAD
FMS-1655 Flush-Mount with Internal Sensor
8. Mount the louvered stainless steel cover
plate to the mounting plate with the screws
supplied.
9. Apply power to the FMS-1655 and confirm
that following a brief initialization sequence,
the unit displays the room differential pressure
and the Safety Halo™ status matches that of
the main display screen. FMS-1655 units are
shipped from the factory in neutral isolation
mode.
- 6 -
MOUNTING/WIRING
Internal Sensor
The FMS-1655 is calibrated with settings programmed in the factory according to the customer specifications. The user can change the settings
by using the instructions provided in the Quick Start section of this manual beginning on page 38.
- 7 -
MOUNTING/WIRING
Notes
- 8 -
Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice.
JCI reserves the right to change product specifications without notice.
MOUNTING/WIRING
FMS-1655 With Remote Sensor
Introduction
The flexibility of the FMS-1655 provides for
several different configurations with respect to
the sensor location.
FMS-1655 models without an internal
sensor include at least one remote sensor
for measuring the differential pressure of the
monitored room. This remote sensor module
must be installed in the wall between the
monitored isolation room and the adjoining
corridor or anteroom.
The remote sensor module should be installed
with the attached stainless steel mounting
plate facing the isolation or patient room and
the reference plate facing the corridor or
anteroom. Please see illustrations on pages
10 and 11 for more details.
With this sensor orientation, a positive
pressure value indicates that the isolation
room is positive with respect to the corridor.
A 3-conductor (22 AWG) cable MUST be
connected between the remote sensor
module and the main controller module for
each sensor included with the unit. The length
of this cable should not exceed 1,000 feet.
The display unit may be installed outside
the room, at the nurses’ station, in the
engineering office, or at any other location as
needed.
Mounting Procedure
1. Cut an opening in the wall of the isolation
room to receive the supplied low voltage
mounting bracket for the remote sensor
electronics. Nominal hole dimensions are
3.65” H x 2.15” W.
2. Drill a 7/16” hole through the opposite wall
for the flow tube as shown.
3. Bring the 3-conductor signal wire through
the cut out.
4. Install the included low-voltage mounting
bracket in the drywall opening, and pull
the 3-conductor signal cable through the
mounting bracket.
5. Push a length of flow tube through the back
hole on through the 7/16” hole in the opposite
wall.
6. Attach the flow tube to the sensor port.
Then, push the tube and sensor module into
place and secure to the mounting enclosure
with two 6-32 x 3/4 screws supplied.
7. Install the louvered cover plate.
8. On the opposite side (corridor) attach the
flow tube to the barbed fitting of the flow tube
mounting plate.
9. Press the mounting plate into place,
allowing the excess tube length to go into
the wall space. Secure with the screws and
anchors.
11. At the FMS-1655 backplane, assuming
the colors of the 3-conductor signal cable
being red, black, and green, connect the
leads to the terminals as follows:
Red: Digital SNS_PWR
Black: AGND
Green: AI_1
If more than one remote sensor is being
used with the FMS-1655, then each must
be connected as above with the green leads
connected to the subsequent analog input
terminals AI_2 through AI_4.
12. Connect the 3-conductor signal cable to
remote sensor as follows:
Red: +Vin
Black: GND
Green: Io
10. Install the louvered cover plate.
- 9 -
NCNCGNDNCNCIoNC
GND
+Vin
~
~
MOUNTING/WIRING
FMS-1655 with Standard Remote Sensor (9-Pin)
CORRIDOR
Gasket
Stainless Steel
Flow Tube
Mounting Plate
Wall Section
(cutaway view)
Flow Tube
When Flow Tube mounting plate
is located directly opposite the
sensor, flow tubing must be cut as
short as possible to prevent kinks.
For connection of
transmitter to FMS-1655.
Terminal
Stainless Steel
Mounting Plate
Gasket
Louvered Cover
Plate
ISOLATION
ROOM
NCNCGNDNCNCIoNC
GND
+Vin
Thin Silicone Caulking
(apply around tube and between
stainless steel plate and wall to seal
unit penetration)
~
~
Orange wall bracket
to be installed first
by using the rotating
clamps for secure
wall attachment.
Standard Remote Sensor Detail
(Side View)
- 10 -
To FMS-1655 Controller
MOUNTING/WIRING
FMS-1655 with Standard Remote Sensor (9-Pin)
Stainless Steel
Flow Tube
Mounting Plate
ISOLATION
ROOM
Gasket
Thin Silicone Caulking
(apply around tube and
between stainless steel
plate and wall to seal unit
penetration)
Sensor installation requires the use of a three
conductor wire between the sensor and the main
controller module.
Flow Tube
When Flow Tube mounting plate is located
directly opposite the sensor, flow tubing must
be cut as short as possible to prevent kinks.
Terminal
For connection of
transmitter to
FMS-1655 .
To FMS-1655
Controller
Wall Section
(cutaway view)
~
~
NCNCGNDNCNCIoNC
Rotating clamps secure
assembly to wall board
GND
Louvered Cover
Plate
+Vin
Gasket
CORRIDOR
Stainless Steel
Mounting Plate
Standard Remote Sensor Detail
(Bottom View)
- 11 -
MOUNTING/WIRING
Remote Sensor Conguration
The electrical connections to the FMS-1655 made via a convenient backplate/backplate assembly is shown below. All wiring should conform
to the local regulations and National Electric Code. Take care not to run sensor wiring in the same conduit as the line voltage or other
conductors that supply highly inductive loads such as generators, motors, solenoids, contactors, etc. Use 22AWG or larger.
{
Recommended 4-conductor
connection: Belden 1325A
Step Down
Isolation Transformer
(provided with FMS Controller)
Controller Configuration Dipswitch Settings
S1 - 1 = ON, S1 - 5 = OFF (AI - 1 set at 4 - 20mA Input)
- 12 -
MOUNTING/WIRING - INTERNAL SENSOR
Analog Output to Electric Damper Actuator
Step Down
Isolation Transformer
(provided with FMS Controller)
Controller Configuration Dipswitch Settings
S1 - 2 = ON, S1 - 6 = OFF (AI - 2 set as 4 - 20mA Input)
S4 - 1 = ON (AO - 1 set as Voltage Output)
- 13 -
MOUNTING/WIRING - INTERNAL SENSOR
Analog Output to Pneumatic Damper Actuator
Optional remote sensor
Step Down
Isolation Transformer
(provided with FMS Controller)
Controller Configuration Dipswitch Settings
S1 - 2 = ON, S1 - 6 = OFF (AI - 2 set as 4 - 20mA Input)
S4 - 1 = ON (AO - 1 set as Voltage Output)
Due to continuous improvement, TRIATEK reserves the right to change product specifications without notice.
- 14 -
Loading...